MIMXRT1052
ADC: 12-bit Analog to Digital Converter Driver
-
void ADC_Init(ADC_Type *base, const adc_config_t *config)
Initialize the ADC module.
- Parameters:
base – ADC peripheral base address.
config – Pointer to “adc_config_t” structure.
-
void ADC_Deinit(ADC_Type *base)
De-initializes the ADC module.
- Parameters:
base – ADC peripheral base address.
-
void ADC_GetDefaultConfig(adc_config_t *config)
Gets an available pre-defined settings for the converter’s configuration.
This function initializes the converter configuration structure with available settings. The default values are:
config->enableAsynchronousClockOutput = true; config->enableOverWrite = false; config->enableContinuousConversion = false; config->enableHighSpeed = false; config->enableLowPower = false; config->enableLongSample = false; config->referenceVoltageSource = kADC_ReferenceVoltageSourceAlt0; config->samplePeriodMode = kADC_SamplePeriod2or12Clocks; config->clockSource = kADC_ClockSourceAD; config->clockDriver = kADC_ClockDriver1; config->resolution = kADC_Resolution12Bit;
- Parameters:
config – Pointer to the configuration structure.
-
void ADC_SetChannelConfig(ADC_Type *base, uint32_t channelGroup, const adc_channel_config_t *config)
Configures the conversion channel.
This operation triggers the conversion when in software trigger mode. When in hardware trigger mode, this API configures the channel while the external trigger source helps to trigger the conversion.
Note that the “Channel Group” has a detailed description. To allow sequential conversions of the ADC to be triggered by internal peripherals, the ADC has more than one group of status and control registers, one for each conversion. The channel group parameter indicates which group of registers are used, for example channel group 0 is for Group A registers and channel group 1 is for Group B registers. The channel groups are used in a “ping-pong” approach to control the ADC operation. At any point, only one of the channel groups is actively controlling ADC conversions. The channel group 0 is used for both software and hardware trigger modes. Channel groups 1 and greater indicate potentially multiple channel group registers for use only in hardware trigger mode. See the chip configuration information in the appropriate MCU reference manual about the number of SC1n registers (channel groups) specific to this device. None of the channel groups 1 or greater are used for software trigger operation. Therefore, writing to these channel groups does not initiate a new conversion. Updating the channel group 0 while a different channel group is actively controlling a conversion is allowed and vice versa. Writing any of the channel group registers while that specific channel group is actively controlling a conversion aborts the current conversion.
- Parameters:
base – ADC peripheral base address.
channelGroup – Channel group index.
config – Pointer to the “adc_channel_config_t” structure for the conversion channel.
-
static inline uint32_t ADC_GetChannelConversionValue(ADC_Type *base, uint32_t channelGroup)
Gets the conversion value.
- Parameters:
base – ADC peripheral base address.
channelGroup – Channel group index.
- Returns:
Conversion value.
-
static inline uint32_t ADC_GetChannelStatusFlags(ADC_Type *base, uint32_t channelGroup)
Gets the status flags of channel.
A conversion is completed when the result of the conversion is transferred into the data result registers. (provided the compare function & hardware averaging is disabled), this is indicated by the setting of COCOn. If hardware averaging is enabled, COCOn sets only, if the last of the selected number of conversions is complete. If the compare function is enabled, COCOn sets and conversion result data is transferred only if the compare condition is true. If both hardware averaging and compare functions are enabled, then COCOn sets only if the last of the selected number of conversions is complete and the compare condition is true.
- Parameters:
base – ADC peripheral base address.
channelGroup – Channel group index.
- Returns:
Status flags of channel.return 0 means COCO flag is 0,return 1 means COCOflag is 1.
-
status_t ADC_DoAutoCalibration(ADC_Type *base)
Automates the hardware calibration.
This auto calibration helps to adjust the plus/minus side gain automatically. Execute the calibration before using the converter. Note that the software trigger should be used during calibration.
- Parameters:
base – ADC peripheral base address.
- Return values:
kStatus_Success – Calibration is done successfully.
kStatus_Fail – Calibration has failed.
- Returns:
Execution status.
-
void ADC_SetOffsetConfig(ADC_Type *base, const adc_offest_config_t *config)
Set user defined offset.
- Parameters:
base – ADC peripheral base address.
config – Pointer to “adc_offest_config_t” structure.
-
static inline void ADC_EnableDMA(ADC_Type *base, bool enable)
Enables generating the DMA trigger when the conversion is complete.
- Parameters:
base – ADC peripheral base address.
enable – Switcher of the DMA feature. “true” means enabled, “false” means not enabled.
-
void ADC_SetHardwareCompareConfig(ADC_Type *base, const adc_hardware_compare_config_t *config)
Enables the hardware trigger mode.
Configures the hardware compare mode.
The hardware compare mode provides a way to process the conversion result automatically by using hardware. Only the result in the compare range is available. To compare the range, see “adc_hardware_compare_mode_t” or the appopriate reference manual for more information.
- Parameters:
base – ADC peripheral base address.
enable – Switcher of the trigger mode. “true” means hardware tirgger mode,”false” means software mode.
base – ADC peripheral base address.
config – Pointer to “adc_hardware_compare_config_t” structure.
-
void ADC_SetHardwareAverageConfig(ADC_Type *base, adc_hardware_average_mode_t mode)
Configures the hardware average mode.
The hardware average mode provides a way to process the conversion result automatically by using hardware. The multiple conversion results are accumulated and averaged internally making them easier to read.
- Parameters:
base – ADC peripheral base address.
mode – Setting the hardware average mode. See “adc_hardware_average_mode_t”.
-
static inline uint32_t ADC_GetStatusFlags(ADC_Type *base)
Gets the converter’s status flags.
- Parameters:
base – ADC peripheral base address.
- Returns:
Flags’ mask if indicated flags are asserted. See “adc_status_flags_t”.
-
void ADC_ClearStatusFlags(ADC_Type *base, uint32_t mask)
Clears the converter’s status falgs.
- Parameters:
base – ADC peripheral base address.
mask – Mask value for the cleared flags. See “adc_status_flags_t”.
-
enum _adc_status_flags
Converter’s status flags.
Values:
-
enumerator kADC_ConversionActiveFlag
Conversion is active,not support w1c.
-
enumerator kADC_CalibrationFailedFlag
Calibration is failed,support w1c.
-
enumerator kADC_AsynchronousWakeupInterruptFlag
Asynchronous wakeup interrupt occurred, support w1c.
-
enumerator kADC_ConversionActiveFlag
-
enum _adc_reference_voltage_source
Reference voltage source.
Values:
-
enumerator kADC_ReferenceVoltageSourceAlt0
For external pins pair of VrefH and VrefL.
-
enumerator kADC_ReferenceVoltageSourceAlt0
-
enum _adc_sample_period_mode
Sample time duration.
Values:
-
enumerator kADC_SamplePeriod2or12Clocks
Long sample 12 clocks or short sample 2 clocks.
-
enumerator kADC_SamplePeriod4or16Clocks
Long sample 16 clocks or short sample 4 clocks.
-
enumerator kADC_SamplePeriod6or20Clocks
Long sample 20 clocks or short sample 6 clocks.
-
enumerator kADC_SamplePeriod8or24Clocks
Long sample 24 clocks or short sample 8 clocks.
-
enumerator kADC_SamplePeriodLong12Clcoks
Long sample 12 clocks.
-
enumerator kADC_SamplePeriodLong16Clcoks
Long sample 16 clocks.
-
enumerator kADC_SamplePeriodLong20Clcoks
Long sample 20 clocks.
-
enumerator kADC_SamplePeriodLong24Clcoks
Long sample 24 clocks.
-
enumerator kADC_SamplePeriodShort2Clocks
Short sample 2 clocks.
-
enumerator kADC_SamplePeriodShort4Clocks
Short sample 4 clocks.
-
enumerator kADC_SamplePeriodShort6Clocks
Short sample 6 clocks.
-
enumerator kADC_SamplePeriodShort8Clocks
Short sample 8 clocks.
-
enumerator kADC_SamplePeriod2or12Clocks
-
enum _adc_clock_source
Clock source.
Values:
-
enumerator kADC_ClockSourceIPG
Select IPG clock to generate ADCK.
-
enumerator kADC_ClockSourceIPGDiv2
Select IPG clock divided by 2 to generate ADCK.
-
enumerator kADC_ClockSourceAD
Select Asynchronous clock to generate ADCK.
-
enumerator kADC_ClockSourceIPG
-
enum _adc_clock_drvier
Clock divider for the converter.
Values:
-
enumerator kADC_ClockDriver1
For divider 1 from the input clock to the module.
-
enumerator kADC_ClockDriver2
For divider 2 from the input clock to the module.
-
enumerator kADC_ClockDriver4
For divider 4 from the input clock to the module.
-
enumerator kADC_ClockDriver8
For divider 8 from the input clock to the module.
-
enumerator kADC_ClockDriver1
-
enum _adc_resolution
Converter’s resolution.
Values:
-
enumerator kADC_Resolution8Bit
Single End 8-bit resolution.
-
enumerator kADC_Resolution10Bit
Single End 10-bit resolution.
-
enumerator kADC_Resolution12Bit
Single End 12-bit resolution.
-
enumerator kADC_Resolution8Bit
-
enum _adc_hardware_compare_mode
Converter hardware compare mode.
Values:
-
enumerator kADC_HardwareCompareMode0
Compare true if the result is less than the value1.
-
enumerator kADC_HardwareCompareMode1
Compare true if the result is greater than or equal to value1.
-
enumerator kADC_HardwareCompareMode2
Value1 <= Value2, compare true if the result is less than value1 Or the result is Greater than value2. Value1 > Value2, compare true if the result is less than value1 And the result is greater than value2
-
enumerator kADC_HardwareCompareMode3
Value1 <= Value2, compare true if the result is greater than or equal to value1 And the result is less than or equal to value2. Value1 > Value2, compare true if the result is greater than or equal to value1 Or the result is less than or equal to value2.
-
enumerator kADC_HardwareCompareMode0
-
enum _adc_hardware_average_mode
Converter hardware average mode.
Values:
-
enumerator kADC_HardwareAverageCount4
For hardware average with 4 samples.
-
enumerator kADC_HardwareAverageCount8
For hardware average with 8 samples.
-
enumerator kADC_HardwareAverageCount16
For hardware average with 16 samples.
-
enumerator kADC_HardwareAverageCount32
For hardware average with 32 samples.
-
enumerator kADC_HardwareAverageDiasable
Disable the hardware average function.
-
enumerator kADC_HardwareAverageCount4
-
typedef enum _adc_status_flags adc_status_flags_t
Converter’s status flags.
-
typedef enum _adc_reference_voltage_source adc_reference_voltage_source_t
Reference voltage source.
-
typedef enum _adc_sample_period_mode adc_sample_period_mode_t
Sample time duration.
-
typedef enum _adc_clock_source adc_clock_source_t
Clock source.
-
typedef enum _adc_clock_drvier adc_clock_driver_t
Clock divider for the converter.
-
typedef enum _adc_resolution adc_resolution_t
Converter’s resolution.
-
typedef enum _adc_hardware_compare_mode adc_hardware_compare_mode_t
Converter hardware compare mode.
-
typedef enum _adc_hardware_average_mode adc_hardware_average_mode_t
Converter hardware average mode.
-
typedef struct _adc_config adc_config_t
Converter configuration.
-
typedef struct _adc_offest_config adc_offest_config_t
Converter Offset configuration.
-
typedef struct _adc_hardware_compare_config adc_hardware_compare_config_t
ADC hardware compare configuration.
In kADC_HardwareCompareMode0, compare true if the result is less than the value1. In kADC_HardwareCompareMode1, compare true if the result is greater than or equal to value1. In kADC_HardwareCompareMode2, Value1 <= Value2, compare true if the result is less than value1 Or the result is Greater than value2. Value1 > Value2, compare true if the result is less than value1 And the result is Greater than value2. In kADC_HardwareCompareMode3, Value1 <= Value2, compare true if the result is greater than or equal to value1 And the result is less than or equal to value2. Value1 > Value2, compare true if the result is greater than or equal to value1 Or the result is less than or equal to value2.
-
typedef struct _adc_channel_config adc_channel_config_t
ADC channel conversion configuration.
-
FSL_ADC_DRIVER_VERSION
ADC driver version.
Version 2.0.4.
-
struct _adc_config
- #include <fsl_adc.h>
Converter configuration.
Public Members
-
bool enableOverWrite
Enable the overwriting.
-
bool enableContinuousConversion
Enable the continuous conversion mode.
-
bool enableHighSpeed
Enable the high-speed mode.
-
bool enableLowPower
Enable the low power mode.
-
bool enableLongSample
Enable the long sample mode.
-
bool enableAsynchronousClockOutput
Enable the asynchronous clock output.
-
adc_reference_voltage_source_t referenceVoltageSource
Select the reference voltage source.
-
adc_sample_period_mode_t samplePeriodMode
Select the sample period in long sample mode or short mode.
-
adc_clock_source_t clockSource
Select the input clock source to generate the internal clock ADCK.
-
adc_clock_driver_t clockDriver
Select the divide ratio used by the ADC to generate the internal clock ADCK.
-
adc_resolution_t resolution
Select the ADC resolution mode.
-
bool enableOverWrite
-
struct _adc_offest_config
- #include <fsl_adc.h>
Converter Offset configuration.
Public Members
-
bool enableSigned
if false,The offset value is added with the raw result. if true,The offset value is subtracted from the raw converted value.
-
uint32_t offsetValue
User configurable offset value(0-4095).
-
bool enableSigned
-
struct _adc_hardware_compare_config
- #include <fsl_adc.h>
ADC hardware compare configuration.
In kADC_HardwareCompareMode0, compare true if the result is less than the value1. In kADC_HardwareCompareMode1, compare true if the result is greater than or equal to value1. In kADC_HardwareCompareMode2, Value1 <= Value2, compare true if the result is less than value1 Or the result is Greater than value2. Value1 > Value2, compare true if the result is less than value1 And the result is Greater than value2. In kADC_HardwareCompareMode3, Value1 <= Value2, compare true if the result is greater than or equal to value1 And the result is less than or equal to value2. Value1 > Value2, compare true if the result is greater than or equal to value1 Or the result is less than or equal to value2.
Public Members
-
adc_hardware_compare_mode_t hardwareCompareMode
Select the hardware compare mode. See “adc_hardware_compare_mode_t”.
-
uint16_t value1
Setting value1(0-4095) for hardware compare mode.
-
uint16_t value2
Setting value2(0-4095) for hardware compare mode.
-
adc_hardware_compare_mode_t hardwareCompareMode
-
struct _adc_channel_config
- #include <fsl_adc.h>
ADC channel conversion configuration.
Public Members
-
uint32_t channelNumber
Setting the conversion channel number. The available range is 0-31. See channel connection information for each chip in Reference Manual document.
-
bool enableInterruptOnConversionCompleted
Generate an interrupt request once the conversion is completed.
-
uint32_t channelNumber
ADC_ETC: ADC External Trigger Control
-
void ADC_ETC_Init(ADC_ETC_Type *base, const adc_etc_config_t *config)
Initialize the ADC_ETC module.
- Parameters:
base – ADC_ETC peripheral base address.
config – Pointer to “adc_etc_config_t” structure.
-
void ADC_ETC_Deinit(ADC_ETC_Type *base)
De-Initialize the ADC_ETC module.
- Parameters:
base – ADC_ETC peripheral base address.
-
void ADC_ETC_GetDefaultConfig(adc_etc_config_t *config)
Gets an available pre-defined settings for the ADC_ETC’s configuration. This function initializes the ADC_ETC’s configuration structure with available settings. The default values are:
config->enableTSCBypass = true; config->enableTSC0Trigger = false; config->enableTSC1Trigger = false; config->TSC0triggerPriority = 0U; config->TSC1triggerPriority = 0U; config->clockPreDivider = 0U; config->XBARtriggerMask = 0U;
- Parameters:
config – Pointer to “adc_etc_config_t” structure.
-
void ADC_ETC_SetTriggerConfig(ADC_ETC_Type *base, uint32_t triggerGroup, const adc_etc_trigger_config_t *config)
Set the external XBAR trigger configuration.
- Parameters:
base – ADC_ETC peripheral base address.
triggerGroup – Trigger group index.
config – Pointer to “adc_etc_trigger_config_t” structure.
-
void ADC_ETC_SetTriggerChainConfig(ADC_ETC_Type *base, uint32_t triggerGroup, uint32_t chainGroup, const adc_etc_trigger_chain_config_t *config)
Set the external XBAR trigger chain configuration. For example, if triggerGroup is set to 0U and chainGroup is set to 1U, which means Trigger0 source’s chain1 would be configurated.
- Parameters:
base – ADC_ETC peripheral base address.
triggerGroup – Trigger group index. Available number is 0~7.
chainGroup – Trigger chain group index. Available number is 0~7.
config – Pointer to “adc_etc_trigger_chain_config_t” structure.
-
uint32_t ADC_ETC_GetInterruptStatusFlags(ADC_ETC_Type *base, adc_etc_external_trigger_source_t sourceIndex)
Gets the interrupt status flags of external XBAR and TSC triggers.
- Parameters:
base – ADC_ETC peripheral base address.
sourceIndex – trigger source index.
- Returns:
Status flags mask of trigger. Refer to “_adc_etc_status_flag_mask”.
-
void ADC_ETC_ClearInterruptStatusFlags(ADC_ETC_Type *base, adc_etc_external_trigger_source_t sourceIndex, uint32_t mask)
Clears the ADC_ETC’s interrupt status falgs.
- Parameters:
base – ADC_ETC peripheral base address.
sourceIndex – trigger source index.
mask – Status flags mask of trigger. Refer to “_adc_etc_status_flag_mask”.
-
static inline void ADC_ETC_EnableDMA(ADC_ETC_Type *base, uint32_t triggerGroup)
Enable the DMA corresponding to each trigger source.
- Parameters:
base – ADC_ETC peripheral base address.
triggerGroup – Trigger group index. Available number is 0~7.
-
static inline void ADC_ETC_DisableDMA(ADC_ETC_Type *base, uint32_t triggerGroup)
Disable the DMA corresponding to each trigger sources.
- Parameters:
base – ADC_ETC peripheral base address.
triggerGroup – Trigger group index. Available number is 0~7.
-
static inline uint32_t ADC_ETC_GetDMAStatusFlags(ADC_ETC_Type *base)
Get the DMA request status falgs. Only external XBAR sources support DMA request.
- Parameters:
base – ADC_ETC peripheral base address.
- Returns:
Mask of external XBAR tirgger’s DMA request asserted flags. Available range is trigger0:0x01 to trigger7:0x80.
-
static inline void ADC_ETC_ClearDMAStatusFlags(ADC_ETC_Type *base, uint32_t mask)
Clear the DMA request status falgs. Only external XBAR sources support DMA request.
- Parameters:
base – ADC_ETC peripheral base address.
mask – Mask of external XBAR tirgger’s DMA request asserted flags. Available range is trigger0:0x01 to trigger7:0x80.
-
static inline void ADC_ETC_DoSoftwareReset(ADC_ETC_Type *base, bool enable)
When enable, all logical will be reset.
- Parameters:
base – ADC_ETC peripheral base address.
enable – Enable/Disable the software reset.
-
static inline void ADC_ETC_DoSoftwareTrigger(ADC_ETC_Type *base, uint32_t triggerGroup)
Do software trigger corresponding to each XBAR trigger sources. Each XBAR trigger sources can be configured as HW or SW trigger mode. In hardware trigger mode, trigger source is from XBAR. In software mode, trigger source is from software tigger. TSC trigger sources can only work in hardware trigger mode.
- Parameters:
base – ADC_ETC peripheral base address.
triggerGroup – Trigger group index. Available number is 0~7.
-
static inline void ADC_ETC_DoSoftwareTriggerBlocking(ADC_ETC_Type *base, uint32_t triggerGroup)
Do software trigger corresponding to each XBAR trigger sources.
Note
This function provides a workaround implementation for ERR052412 by using blocking way to implement SW trigger.
- Parameters:
base – ADC_ETC peripheral base address.
triggerGroup – Trigger group index. Available number is 0~7.
-
uint32_t ADC_ETC_GetADCConversionValue(ADC_ETC_Type *base, uint32_t triggerGroup, uint32_t chainGroup)
Get ADC conversion result from external XBAR sources. For example, if triggerGroup is set to 0U and chainGroup is set to 1U, which means the API would return Trigger0 source’s chain1 conversion result.
- Parameters:
base – ADC_ETC peripheral base address.
triggerGroup – Trigger group index. Available number is 0~7.
chainGroup – Trigger chain group index. Available number is 0~7.
- Returns:
ADC conversion result value.
-
enum _adc_etc_status_flag_mask
ADC_ETC customized status flags mask.
Values:
-
enumerator kADC_ETC_Done0StatusFlagMask
-
enumerator kADC_ETC_Done1StatusFlagMask
-
enumerator kADC_ETC_Done2StatusFlagMask
-
enumerator kADC_ETC_Done3StatusFlagMask
-
enumerator kADC_ETC_ErrorStatusFlagMask
-
enumerator kADC_ETC_Done0StatusFlagMask
-
enum _adc_etc_external_trigger_source
External triggers sources.
Values:
-
enumerator kADC_ETC_Trg0TriggerSource
-
enumerator kADC_ETC_Trg1TriggerSource
-
enumerator kADC_ETC_Trg2TriggerSource
-
enumerator kADC_ETC_Trg3TriggerSource
-
enumerator kADC_ETC_Trg4TriggerSource
-
enumerator kADC_ETC_Trg5TriggerSource
-
enumerator kADC_ETC_Trg6TriggerSource
-
enumerator kADC_ETC_Trg7TriggerSource
-
enumerator kADC_ETC_TSC0TriggerSource
-
enumerator kADC_ETC_TSC1TriggerSource
-
enumerator kADC_ETC_Trg0TriggerSource
-
enum _adc_etc_interrupt_enable
Interrupt enable/disable mask.
Values:
-
enumerator kADC_ETC_Done0InterruptEnable
-
enumerator kADC_ETC_Done1InterruptEnable
-
enumerator kADC_ETC_Done2InterruptEnable
-
enumerator kADC_ETC_Done3InterruptEnable
-
enumerator kADC_ETC_Done0InterruptEnable
-
enum _adc_etc_dma_mode_selection
DMA mode selection.
Values:
-
enumerator kADC_ETC_TrigDMAWithLatchedSignal
-
enumerator kADC_ETC_TrigDMAWithPulsedSignal
-
enumerator kADC_ETC_TrigDMAWithLatchedSignal
-
typedef enum _adc_etc_external_trigger_source adc_etc_external_trigger_source_t
External triggers sources.
-
typedef enum _adc_etc_interrupt_enable adc_etc_interrupt_enable_t
Interrupt enable/disable mask.
-
typedef enum _adc_etc_dma_mode_selection adc_etc_dma_mode_selection_t
DMA mode selection.
-
typedef struct _adc_etc_config adc_etc_config_t
ADC_ETC configuration.
-
typedef struct _adc_etc_trigger_chain_config adc_etc_trigger_chain_config_t
ADC_ETC trigger chain configuration.
-
typedef struct _adc_etc_trigger_config adc_etc_trigger_config_t
ADC_ETC trigger configuration.
-
FSL_ADC_ETC_DRIVER_VERSION
ADC_ETC driver version.
Version 2.3.0.
-
ADC_ETC_DMA_CTRL_TRGn_REQ_MASK
The mask of status flags cleared by writing 1.
-
struct _adc_etc_config
- #include <fsl_adc_etc.h>
ADC_ETC configuration.
-
struct _adc_etc_trigger_chain_config
- #include <fsl_adc_etc.h>
ADC_ETC trigger chain configuration.
-
struct _adc_etc_trigger_config
- #include <fsl_adc_etc.h>
ADC_ETC trigger configuration.
AIPSTZ: AHB to IP Bridge
-
void AIPSTZ_SetMasterPriviledgeLevel(AIPSTZ_Type *base, aipstz_master_t master, uint32_t privilegeConfig)
Configure the privilege level for master.
- Parameters:
base – AIPSTZ peripheral base pointer
master – Masters for AIPSTZ.
privilegeConfig – Configuration is ORed from aipstz_master_privilege_level_t.
-
void AIPSTZ_SetPeripheralAccessControl(AIPSTZ_Type *base, aipstz_peripheral_t peripheral, uint32_t accessControl)
Configure the access for peripheral.
- Parameters:
base – AIPSTZ peripheral base pointer
peripheral – Peripheral for AIPSTZ.
accessControl – Configuration is ORed from aipstz_peripheral_access_control_t.
-
FSL_AIPSTZ_DRIVER_VERSION
Version 2.0.1
-
enum _aipstz_master_privilege_level
List of AIPSTZ privilege configuration.
Values:
-
enumerator kAIPSTZ_MasterBufferedWriteEnable
Write accesses from this master are allowed to be buffered.
-
enumerator kAIPSTZ_MasterTrustedForReadEnable
This master is trusted for read accesses.
-
enumerator kAIPSTZ_MasterTrustedForWriteEnable
This master is trusted for write accesses.
-
enumerator kAIPSTZ_MasterForceUserModeEnable
Accesses from this master are forced to user-mode.
-
enumerator kAIPSTZ_MasterBufferedWriteEnable
-
enum _aipstz_master
List of AIPSTZ masters. Organized by width for the 8-15 bits and shift for lower 8 bits.
Values:
-
enumerator kAIPSTZ_Master0
-
enumerator kAIPSTZ_Master1
-
enumerator kAIPSTZ_Master2
-
enumerator kAIPSTZ_Master3
-
enumerator kAIPSTZ_Master5
-
enumerator kAIPSTZ_Master0
-
enum _aipstz_peripheral_access_control
List of AIPSTZ peripheral access control configuration.
Values:
-
enumerator kAIPSTZ_PeripheralAllowUntrustedMaster
-
enumerator kAIPSTZ_PeripheralWriteProtected
-
enumerator kAIPSTZ_PeripheralRequireSupervisor
-
enumerator kAIPSTZ_PeripheralAllowBufferedWrite
-
enumerator kAIPSTZ_PeripheralAllowUntrustedMaster
-
enum _aipstz_peripheral
List of AIPSTZ peripherals. Organized by register offset for higher 32 bits, width for the 8-15 bits and shift for lower 8 bits.
Values:
-
enumerator kAIPSTZ_Peripheral0
-
enumerator kAIPSTZ_Peripheral1
-
enumerator kAIPSTZ_Peripheral2
-
enumerator kAIPSTZ_Peripheral3
-
enumerator kAIPSTZ_Peripheral4
-
enumerator kAIPSTZ_Peripheral5
-
enumerator kAIPSTZ_Peripheral6
-
enumerator kAIPSTZ_Peripheral7
-
enumerator kAIPSTZ_Peripheral8
-
enumerator kAIPSTZ_Peripheral9
-
enumerator kAIPSTZ_Peripheral10
-
enumerator kAIPSTZ_Peripheral11
-
enumerator kAIPSTZ_Peripheral12
-
enumerator kAIPSTZ_Peripheral13
-
enumerator kAIPSTZ_Peripheral14
-
enumerator kAIPSTZ_Peripheral15
-
enumerator kAIPSTZ_Peripheral16
-
enumerator kAIPSTZ_Peripheral17
-
enumerator kAIPSTZ_Peripheral18
-
enumerator kAIPSTZ_Peripheral19
-
enumerator kAIPSTZ_Peripheral20
-
enumerator kAIPSTZ_Peripheral21
-
enumerator kAIPSTZ_Peripheral22
-
enumerator kAIPSTZ_Peripheral23
-
enumerator kAIPSTZ_Peripheral24
-
enumerator kAIPSTZ_Peripheral25
-
enumerator kAIPSTZ_Peripheral26
-
enumerator kAIPSTZ_Peripheral27
-
enumerator kAIPSTZ_Peripheral28
-
enumerator kAIPSTZ_Peripheral29
-
enumerator kAIPSTZ_Peripheral30
-
enumerator kAIPSTZ_Peripheral31
-
enumerator kAIPSTZ_Peripheral32
-
enumerator kAIPSTZ_Peripheral33
-
enumerator kAIPSTZ_Peripheral0
-
typedef enum _aipstz_master_privilege_level aipstz_master_privilege_level_t
List of AIPSTZ privilege configuration.
-
typedef enum _aipstz_master aipstz_master_t
List of AIPSTZ masters. Organized by width for the 8-15 bits and shift for lower 8 bits.
-
typedef enum _aipstz_peripheral_access_control aipstz_peripheral_access_control_t
List of AIPSTZ peripheral access control configuration.
-
typedef enum _aipstz_peripheral aipstz_peripheral_t
List of AIPSTZ peripherals. Organized by register offset for higher 32 bits, width for the 8-15 bits and shift for lower 8 bits.
AOI: Crossbar AND/OR/INVERT Driver
-
void AOI_Init(AOI_Type *base)
Initializes an AOI instance for operation.
This function un-gates the AOI clock.
- Parameters:
base – AOI peripheral address.
-
void AOI_Deinit(AOI_Type *base)
Deinitializes an AOI instance for operation.
This function shutdowns AOI module.
- Parameters:
base – AOI peripheral address.
-
void AOI_GetEventLogicConfig(AOI_Type *base, aoi_event_t event, aoi_event_config_t *config)
Gets the Boolean evaluation associated.
This function returns the Boolean evaluation associated.
Example:
aoi_event_config_t demoEventLogicStruct; AOI_GetEventLogicConfig(AOI, kAOI_Event0, &demoEventLogicStruct);
- Parameters:
base – AOI peripheral address.
event – Index of the event which will be set of type aoi_event_t.
config – Selected input configuration .
-
void AOI_SetEventLogicConfig(AOI_Type *base, aoi_event_t event, const aoi_event_config_t *eventConfig)
Configures an AOI event.
This function configures an AOI event according to the aoiEventConfig structure. This function configures all inputs (A, B, C, and D) of all product terms (0, 1, 2, and 3) of a desired event.
Example:
aoi_event_config_t demoEventLogicStruct; demoEventLogicStruct.PT0AC = kAOI_InvInputSignal; demoEventLogicStruct.PT0BC = kAOI_InputSignal; demoEventLogicStruct.PT0CC = kAOI_LogicOne; demoEventLogicStruct.PT0DC = kAOI_LogicOne; demoEventLogicStruct.PT1AC = kAOI_LogicZero; demoEventLogicStruct.PT1BC = kAOI_LogicOne; demoEventLogicStruct.PT1CC = kAOI_LogicOne; demoEventLogicStruct.PT1DC = kAOI_LogicOne; demoEventLogicStruct.PT2AC = kAOI_LogicZero; demoEventLogicStruct.PT2BC = kAOI_LogicOne; demoEventLogicStruct.PT2CC = kAOI_LogicOne; demoEventLogicStruct.PT2DC = kAOI_LogicOne; demoEventLogicStruct.PT3AC = kAOI_LogicZero; demoEventLogicStruct.PT3BC = kAOI_LogicOne; demoEventLogicStruct.PT3CC = kAOI_LogicOne; demoEventLogicStruct.PT3DC = kAOI_LogicOne; AOI_SetEventLogicConfig(AOI, kAOI_Event0, demoEventLogicStruct);
- Parameters:
base – AOI peripheral address.
event – Event which will be configured of type aoi_event_t.
eventConfig – Pointer to type aoi_event_config_t structure. The user is responsible for filling out the members of this structure and passing the pointer to this function.
-
FSL_AOI_DRIVER_VERSION
Version 2.0.2.
-
enum _aoi_input_config
AOI input configurations.
The selection item represents the Boolean evaluations.
Values:
-
enumerator kAOI_LogicZero
Forces the input to logical zero.
-
enumerator kAOI_InputSignal
Passes the input signal.
-
enumerator kAOI_InvInputSignal
Inverts the input signal.
-
enumerator kAOI_LogicOne
Forces the input to logical one.
-
enumerator kAOI_LogicZero
-
enum _aoi_event
AOI event indexes, where an event is the collection of the four product terms (0, 1, 2, and 3) and the four signal inputs (A, B, C, and D).
Values:
-
enumerator kAOI_Event0
Event 0 index
-
enumerator kAOI_Event1
Event 1 index
-
enumerator kAOI_Event2
Event 2 index
-
enumerator kAOI_Event3
Event 3 index
-
enumerator kAOI_Event0
-
typedef enum _aoi_input_config aoi_input_config_t
AOI input configurations.
The selection item represents the Boolean evaluations.
-
typedef enum _aoi_event aoi_event_t
AOI event indexes, where an event is the collection of the four product terms (0, 1, 2, and 3) and the four signal inputs (A, B, C, and D).
-
typedef struct _aoi_event_config aoi_event_config_t
AOI event configuration structure.
Defines structure _aoi_event_config and use the AOI_SetEventLogicConfig() function to make whole event configuration.
-
AOI
AOI peripheral address
-
struct _aoi_event_config
- #include <fsl_aoi.h>
AOI event configuration structure.
Defines structure _aoi_event_config and use the AOI_SetEventLogicConfig() function to make whole event configuration.
Public Members
-
aoi_input_config_t PT0AC
Product term 0 input A
-
aoi_input_config_t PT0BC
Product term 0 input B
-
aoi_input_config_t PT0CC
Product term 0 input C
-
aoi_input_config_t PT0DC
Product term 0 input D
-
aoi_input_config_t PT1AC
Product term 1 input A
-
aoi_input_config_t PT1BC
Product term 1 input B
-
aoi_input_config_t PT1CC
Product term 1 input C
-
aoi_input_config_t PT1DC
Product term 1 input D
-
aoi_input_config_t PT2AC
Product term 2 input A
-
aoi_input_config_t PT2BC
Product term 2 input B
-
aoi_input_config_t PT2CC
Product term 2 input C
-
aoi_input_config_t PT2DC
Product term 2 input D
-
aoi_input_config_t PT3AC
Product term 3 input A
-
aoi_input_config_t PT3BC
Product term 3 input B
-
aoi_input_config_t PT3CC
Product term 3 input C
-
aoi_input_config_t PT3DC
Product term 3 input D
-
aoi_input_config_t PT0AC
BEE: Bus Encryption Engine
-
FSL_BEE_DRIVER_VERSION
BEE driver version. Version 2.0.2.
Current version: 2.0.2
Change log:
2.0.2
Bug Fixes
Fixed MISRA issue.
2.0.1
Bug Fixes
Fixed bug in key user key loading sequence. BEE must be enabled during loading of user key.
Fixed typos in comments.
New Features
Added configuration setting for endian swap, access permission and region security level.
Improvements
Setting of AES nonce was moved from BEE_SetRegionKey() into separate BEE_SetRegionNonce() function.
Changed handling of region settings. Both regions are configured simultaneously by BEE_SetConfig() function. Configuration of FAC start and end address using IOMUXC_GPRs was moved to application.
Default value for region address offset was changed to 0.
2.0.0
Initial version
-
enum _bee_aes_mode
BEE aes mode.
Values:
-
enumerator kBEE_AesEcbMode
AES ECB Mode
-
enumerator kBEE_AesCtrMode
AES CTR Mode
-
enumerator kBEE_AesEcbMode
-
enum _bee_region
BEE region.
Values:
-
enumerator kBEE_Region0
BEE region 0
-
enumerator kBEE_Region1
BEE region 1
-
enumerator kBEE_Region0
-
enum _bee_ac_prot_enable
BEE ac prot enable.
Values:
-
enumerator kBEE_AccessProtDisabled
BEE access permission control disabled
-
enumerator kBEE_AccessProtEnabled
BEE access permission control enabled
-
enumerator kBEE_AccessProtDisabled
-
enum _bee_endian_swap_enable
BEE endian swap enable.
Values:
-
enumerator kBEE_EndianSwapDisabled
BEE endian swap disabled
-
enumerator kBEE_EndianSwapEnabled
BEE endian swap enabled
-
enumerator kBEE_EndianSwapDisabled
-
enum _bee_security_level
BEE security level.
Values:
-
enumerator kBEE_SecurityLevel0
BEE security level 0
-
enumerator kBEE_SecurityLevel1
BEE security level 1
-
enumerator kBEE_SecurityLevel2
BEE security level 2
-
enumerator kBEE_SecurityLevel3
BEE security level 3
-
enumerator kBEE_SecurityLevel0
-
enum _bee_status_flags
BEE status flags.
Values:
-
enumerator kBEE_DisableAbortFlag
Disable abort flag.
-
enumerator kBEE_Reg0ReadSecViolation
Region-0 read channel security violation
-
enumerator kBEE_ReadIllegalAccess
Read channel illegal access detected
-
enumerator kBEE_Reg1ReadSecViolation
Region-1 read channel security violation
-
enumerator kBEE_Reg0AccessViolation
Protected region-0 access violation
-
enumerator kBEE_Reg1AccessViolation
Protected region-1 access violation
-
enumerator kBEE_IdleFlag
Idle flag
-
enumerator kBEE_DisableAbortFlag
-
typedef enum _bee_aes_mode bee_aes_mode_t
BEE aes mode.
-
typedef enum _bee_region bee_region_t
BEE region.
-
typedef enum _bee_ac_prot_enable bee_ac_prot_enable
BEE ac prot enable.
-
typedef enum _bee_endian_swap_enable bee_endian_swap_enable
BEE endian swap enable.
-
typedef enum _bee_security_level bee_security_level
BEE security level.
-
typedef enum _bee_status_flags bee_status_flags_t
BEE status flags.
-
typedef struct _bee_region_config bee_region_config_t
BEE region configuration structure.
-
void BEE_Init(BEE_Type *base)
Resets BEE module to factory default values.
This function performs hardware reset of BEE module. Attributes and keys from software for both regions are cleared.
- Parameters:
base – BEE peripheral address.
-
void BEE_Deinit(BEE_Type *base)
Resets BEE module, clears keys for both regions and disables clock to the BEE.
This function performs hardware reset of BEE module and disables clocks. Attributes and keys from software for both regions are cleared.
- Parameters:
base – BEE peripheral address.
-
static inline void BEE_Enable(BEE_Type *base)
Enables BEE decryption.
This function enables decryption using BEE.
- Parameters:
base – BEE peripheral address.
-
static inline void BEE_Disable(BEE_Type *base)
Disables BEE decryption.
This function disables decryption using BEE.
- Parameters:
base – BEE peripheral address.
-
void BEE_GetDefaultConfig(bee_region_config_t *config)
Loads default values to the BEE region configuration structure.
Loads default values to the BEE region configuration structure. The default values are as follows:
config->region0Mode = kBEE_AesCtrMode; config->region1Mode = kBEE_AesCtrMode; config->region0AddrOffset = 0U; config->region1AddrOffset = 0U; config->region0SecLevel = kBEE_SecurityLevel3; config->region1SecLevel = kBEE_SecurityLevel3; config->region1Bot = 0U; config->region1Top = 0U; config->accessPermission = kBEE_AccessProtDisabled; config->endianSwapEn = kBEE_EndianSwapEnabled;
- Parameters:
config – Configuration structure for BEE peripheral.
-
void BEE_SetConfig(BEE_Type *base, const bee_region_config_t *config)
Sets BEE configuration.
This function sets BEE peripheral and BEE region settings accorging to given configuration structure.
- Parameters:
base – BEE peripheral address.
config – Configuration structure for BEE.
-
status_t BEE_SetRegionKey(BEE_Type *base, bee_region_t region, const uint8_t *key, size_t keySize)
Loads the AES key for selected region into BEE key registers.
This function loads given AES key to BEE register for the given region. The key must be 32-bit aligned and stored in little-endian format.
Please note, that eFuse BEE_KEYx_SEL must be set accordingly to be able to load and use key loaded in BEE registers. Otherwise, key cannot loaded and BEE will use key from OTPMK or SW_GP2.
- Parameters:
base – BEE peripheral address.
region – Selection of the BEE region to be configured.
key – AES key (in little-endian format).
keySize – Size of AES key.
-
status_t BEE_SetRegionNonce(BEE_Type *base, bee_region_t region, const uint8_t *nonce, size_t nonceSize)
Loads the nonce for selected region into BEE nonce registers.
This function loads given nonce(only AES CTR mode) to BEE register for the given region. The nonce must be 32-bit aligned and stored in little-endian format.
- Parameters:
base – BEE peripheral address.
region – Selection of the BEE region to be configured.
nonce – AES nonce (in little-endian format).
nonceSize – Size of AES nonce.
-
uint32_t BEE_GetStatusFlags(BEE_Type *base)
Gets the BEE status flags.
This function returns status of BEE peripheral.
- Parameters:
base – BEE peripheral address.
- Returns:
The status flags. This is the logical OR of members of the enumeration bee_status_flags_t
-
void BEE_ClearStatusFlags(BEE_Type *base, uint32_t mask)
Clears the BEE status flags.
- Parameters:
base – BEE peripheral base address.
mask – The status flags to clear. This is a logical OR of members of the enumeration bee_status_flags_t
-
struct _bee_region_config
- #include <fsl_bee.h>
BEE region configuration structure.
Public Members
-
bee_aes_mode_t region0Mode
AES mode used for encryption/decryption for region 0
-
bee_aes_mode_t region1Mode
AES mode used for encryption/decryption for region 1
-
uint32_t region0AddrOffset
Region 0 address offset
-
uint32_t region1AddrOffset
Region 1 address offset
-
bee_security_level region0SecLevel
Region 0 security level
-
bee_security_level region1SecLevel
Region 1 security level
-
uint32_t region1Bot
Region 1 bottom address
-
uint32_t region1Top
Region 1 top address
-
bee_ac_prot_enable accessPermission
Access permission control enable/disable
-
bee_endian_swap_enable endianSwapEn
Endian swap enable/disable
-
bee_aes_mode_t region0Mode
CACHE: ARMV7-M7 CACHE Memory Controller
-
static inline void L1CACHE_EnableICache(void)
Enables cortex-m7 L1 instruction cache.
-
static inline void L1CACHE_DisableICache(void)
Disables cortex-m7 L1 instruction cache.
-
static inline void L1CACHE_InvalidateICache(void)
Invalidate cortex-m7 L1 instruction cache.
-
void L1CACHE_InvalidateICacheByRange(uint32_t address, uint32_t size_byte)
Invalidate cortex-m7 L1 instruction cache by range.
Note
The start address and size_byte should be 32-byte(FSL_FEATURE_L1ICACHE_LINESIZE_BYTE) aligned. The startAddr here will be forced to align to L1 I-cache line size if startAddr is not aligned. For the size_byte, application should make sure the alignment or make sure the right operation order if the size_byte is not aligned.
- Parameters:
address – The start address of the memory to be invalidated.
size_byte – The memory size.
-
static inline void L1CACHE_EnableDCache(void)
Enables cortex-m7 L1 data cache.
-
static inline void L1CACHE_DisableDCache(void)
Disables cortex-m7 L1 data cache.
-
static inline void L1CACHE_InvalidateDCache(void)
Invalidates cortex-m7 L1 data cache.
-
static inline void L1CACHE_CleanDCache(void)
Cleans cortex-m7 L1 data cache.
-
static inline void L1CACHE_CleanInvalidateDCache(void)
Cleans and Invalidates cortex-m7 L1 data cache.
-
static inline void L1CACHE_InvalidateDCacheByRange(uint32_t address, uint32_t size_byte)
Invalidates cortex-m7 L1 data cache by range.
Note
The start address and size_byte should be 32-byte(FSL_FEATURE_L1DCACHE_LINESIZE_BYTE) aligned. The startAddr here will be forced to align to L1 D-cache line size if startAddr is not aligned. For the size_byte, application should make sure the alignment or make sure the right operation order if the size_byte is not aligned.
- Parameters:
address – The start address of the memory to be invalidated.
size_byte – The memory size.
-
static inline void L1CACHE_CleanDCacheByRange(uint32_t address, uint32_t size_byte)
Cleans cortex-m7 L1 data cache by range.
Note
The start address and size_byte should be 32-byte(FSL_FEATURE_L1DCACHE_LINESIZE_BYTE) aligned. The startAddr here will be forced to align to L1 D-cache line size if startAddr is not aligned. For the size_byte, application should make sure the alignment or make sure the right operation order if the size_byte is not aligned.
- Parameters:
address – The start address of the memory to be cleaned.
size_byte – The memory size.
-
static inline void L1CACHE_CleanInvalidateDCacheByRange(uint32_t address, uint32_t size_byte)
Cleans and Invalidates cortex-m7 L1 data cache by range.
Note
The start address and size_byte should be 32-byte(FSL_FEATURE_L1DCACHE_LINESIZE_BYTE) aligned. The startAddr here will be forced to align to L1 D-cache line size if startAddr is not aligned. For the size_byte, application should make sure the alignment or make sure the right operation order if the size_byte is not aligned.
- Parameters:
address – The start address of the memory to be clean and invalidated.
size_byte – The memory size.
-
void ICACHE_InvalidateByRange(uint32_t address, uint32_t size_byte)
Invalidates all instruction caches by range.
Both cortex-m7 L1 cache line and L2 PL310 cache line length is 32-byte.
Note
address and size should be aligned to cache line size 32-Byte due to the cache operation unit is one cache line. The startAddr here will be forced to align to the cache line size if startAddr is not aligned. For the size_byte, application should make sure the alignment or make sure the right operation order if the size_byte is not aligned.
- Parameters:
address – The physical address.
size_byte – size of the memory to be invalidated.
-
void DCACHE_InvalidateByRange(uint32_t address, uint32_t size_byte)
Invalidates all data caches by range.
Both cortex-m7 L1 cache line and L2 PL310 cache line length is 32-byte.
Note
address and size should be aligned to cache line size 32-Byte due to the cache operation unit is one cache line. The startAddr here will be forced to align to the cache line size if startAddr is not aligned. For the size_byte, application should make sure the alignment or make sure the right operation order if the size_byte is not aligned.
- Parameters:
address – The physical address.
size_byte – size of the memory to be invalidated.
-
void DCACHE_CleanByRange(uint32_t address, uint32_t size_byte)
Cleans all data caches by range.
Both cortex-m7 L1 cache line and L2 PL310 cache line length is 32-byte.
Note
address and size should be aligned to cache line size 32-Byte due to the cache operation unit is one cache line. The startAddr here will be forced to align to the cache line size if startAddr is not aligned. For the size_byte, application should make sure the alignment or make sure the right operation order if the size_byte is not aligned.
- Parameters:
address – The physical address.
size_byte – size of the memory to be cleaned.
-
void DCACHE_CleanInvalidateByRange(uint32_t address, uint32_t size_byte)
Cleans and Invalidates all data caches by range.
Both cortex-m7 L1 cache line and L2 PL310 cache line length is 32-byte.
Note
address and size should be aligned to cache line size 32-Byte due to the cache operation unit is one cache line. The startAddr here will be forced to align to the cache line size if startAddr is not aligned. For the size_byte, application should make sure the alignment or make sure the right operation order if the size_byte is not aligned.
- Parameters:
address – The physical address.
size_byte – size of the memory to be cleaned and invalidated.
-
FSL_CACHE_DRIVER_VERSION
cache driver version 2.0.4.
Clock Driver
-
enum _clock_name
Clock name used to get clock frequency.
Values:
-
enumerator kCLOCK_CpuClk
CPU clock
-
enumerator kCLOCK_AhbClk
AHB clock
-
enumerator kCLOCK_SemcClk
SEMC clock
-
enumerator kCLOCK_IpgClk
IPG clock
-
enumerator kCLOCK_PerClk
PER clock
-
enumerator kCLOCK_OscClk
OSC clock selected by PMU_LOWPWR_CTRL[OSC_SEL].
-
enumerator kCLOCK_RtcClk
RTC clock. (RTCCLK)
-
enumerator kCLOCK_ArmPllClk
ARMPLLCLK.
-
enumerator kCLOCK_Usb1PllClk
USB1PLLCLK.
-
enumerator kCLOCK_Usb1PllPfd0Clk
USB1PLLPDF0CLK.
-
enumerator kCLOCK_Usb1PllPfd1Clk
USB1PLLPFD1CLK.
-
enumerator kCLOCK_Usb1PllPfd2Clk
USB1PLLPFD2CLK.
-
enumerator kCLOCK_Usb1PllPfd3Clk
USB1PLLPFD3CLK.
-
enumerator kCLOCK_Usb1SwClk
USB1PLLSWCLK
-
enumerator kCLOCK_Usb1Sw120MClk
USB1PLLSw120MCLK
-
enumerator kCLOCK_Usb1Sw60MClk
USB1PLLSw60MCLK
-
enumerator kCLOCK_Usb1Sw80MClk
USB1PLLSw80MCLK
-
enumerator kCLOCK_Usb2PllClk
USB2PLLCLK.
-
enumerator kCLOCK_SysPllClk
SYSPLLCLK.
-
enumerator kCLOCK_SysPllPfd0Clk
SYSPLLPDF0CLK.
-
enumerator kCLOCK_SysPllPfd1Clk
SYSPLLPFD1CLK.
-
enumerator kCLOCK_SysPllPfd2Clk
SYSPLLPFD2CLK.
-
enumerator kCLOCK_SysPllPfd3Clk
SYSPLLPFD3CLK.
-
enumerator kCLOCK_EnetPll0Clk
Enet PLLCLK ref_enetpll0.
-
enumerator kCLOCK_EnetPll1Clk
Enet PLLCLK ref_enetpll1.
-
enumerator kCLOCK_AudioPllClk
Audio PLLCLK.
-
enumerator kCLOCK_VideoPllClk
Video PLLCLK.
-
enumerator kCLOCK_NoneName
None Clock Name.
-
enumerator kCLOCK_CpuClk
-
enum _clock_ip_name
CCM CCGR gate control for each module independently.
Values:
-
enumerator kCLOCK_IpInvalid
-
enumerator kCLOCK_Aips_tz1
CCGR0, CG0
-
enumerator kCLOCK_Aips_tz2
CCGR0, CG1
-
enumerator kCLOCK_Mqs
CCGR0, CG2
-
enumerator kCLOCK_FlexSpiExsc
CCGR0, CG3
-
enumerator kCLOCK_Sim_M_Main
CCGR0, CG4
-
enumerator kCLOCK_Dcp
CCGR0, CG5
-
enumerator kCLOCK_Lpuart3
CCGR0, CG6
-
enumerator kCLOCK_Can1
CCGR0, CG7
-
enumerator kCLOCK_Can1S
CCGR0, CG8
-
enumerator kCLOCK_Can2
CCGR0, CG9
-
enumerator kCLOCK_Can2S
CCGR0, CG10
-
enumerator kCLOCK_Trace
CCGR0, CG11
-
enumerator kCLOCK_Gpt2
CCGR0, CG12
-
enumerator kCLOCK_Gpt2S
CCGR0, CG13
-
enumerator kCLOCK_Lpuart2
CCGR0, CG14
-
enumerator kCLOCK_Gpio2
CCGR0, CG15
-
enumerator kCLOCK_Lpspi1
CCGR1, CG0
-
enumerator kCLOCK_Lpspi2
CCGR1, CG1
-
enumerator kCLOCK_Lpspi3
CCGR1, CG2
-
enumerator kCLOCK_Lpspi4
CCGR1, CG3
-
enumerator kCLOCK_Adc2
CCGR1, CG4
-
enumerator kCLOCK_Enet
CCGR1, CG5
-
enumerator kCLOCK_Pit
CCGR1, CG6
-
enumerator kCLOCK_Aoi2
CCGR1, CG7
-
enumerator kCLOCK_Adc1
CCGR1, CG8
-
enumerator kCLOCK_SemcExsc
CCGR1, CG9
-
enumerator kCLOCK_Gpt1
CCGR1, CG10
-
enumerator kCLOCK_Gpt1S
CCGR1, CG11
-
enumerator kCLOCK_Lpuart4
CCGR1, CG12
-
enumerator kCLOCK_Gpio1
CCGR1, CG13
-
enumerator kCLOCK_Csu
CCGR1, CG14
-
enumerator kCLOCK_Gpio5
CCGR1, CG15
-
enumerator kCLOCK_OcramExsc
CCGR2, CG0
-
enumerator kCLOCK_Csi
CCGR2, CG1
-
enumerator kCLOCK_IomuxcSnvs
CCGR2, CG2
-
enumerator kCLOCK_Lpi2c1
CCGR2, CG3
-
enumerator kCLOCK_Lpi2c2
CCGR2, CG4
-
enumerator kCLOCK_Lpi2c3
CCGR2, CG5
-
enumerator kCLOCK_Ocotp
CCGR2, CG6
-
enumerator kCLOCK_Xbar3
CCGR2, CG7
-
enumerator kCLOCK_Ipmux1
CCGR2, CG8
-
enumerator kCLOCK_Ipmux2
CCGR2, CG9
-
enumerator kCLOCK_Ipmux3
CCGR2, CG10
-
enumerator kCLOCK_Xbar1
CCGR2, CG11
-
enumerator kCLOCK_Xbar2
CCGR2, CG12
-
enumerator kCLOCK_Gpio3
CCGR2, CG13
-
enumerator kCLOCK_Lcd
CCGR2, CG14
-
enumerator kCLOCK_Pxp
CCGR2, CG15
-
enumerator kCLOCK_Flexio2
CCGR3, CG0
-
enumerator kCLOCK_Lpuart5
CCGR3, CG1
-
enumerator kCLOCK_Semc
CCGR3, CG2
-
enumerator kCLOCK_Lpuart6
CCGR3, CG3
-
enumerator kCLOCK_Aoi1
CCGR3, CG4
-
enumerator kCLOCK_LcdPixel
CCGR3, CG5
-
enumerator kCLOCK_Gpio4
CCGR3, CG6
-
enumerator kCLOCK_Ewm0
CCGR3, CG7
-
enumerator kCLOCK_Wdog1
CCGR3, CG8
-
enumerator kCLOCK_FlexRam
CCGR3, CG9
-
enumerator kCLOCK_Acmp1
CCGR3, CG10
-
enumerator kCLOCK_Acmp2
CCGR3, CG11
-
enumerator kCLOCK_Acmp3
CCGR3, CG12
-
enumerator kCLOCK_Acmp4
CCGR3, CG13
-
enumerator kCLOCK_Ocram
CCGR3, CG14
-
enumerator kCLOCK_IomuxcSnvsGpr
CCGR3, CG15
-
enumerator kCLOCK_Sim_m7_clk_r
CCGR4, CG0
-
enumerator kCLOCK_Iomuxc
CCGR4, CG1
-
enumerator kCLOCK_IomuxcGpr
CCGR4, CG2
-
enumerator kCLOCK_Bee
CCGR4, CG3
-
enumerator kCLOCK_SimM7
CCGR4, CG4
-
enumerator kCLOCK_Tsc
CCGR4, CG5
-
enumerator kCLOCK_SimM
CCGR4, CG6
-
enumerator kCLOCK_SimEms
CCGR4, CG7
-
enumerator kCLOCK_Pwm1
CCGR4, CG8
-
enumerator kCLOCK_Pwm2
CCGR4, CG9
-
enumerator kCLOCK_Pwm3
CCGR4, CG10
-
enumerator kCLOCK_Pwm4
CCGR4, CG11
-
enumerator kCLOCK_Enc1
CCGR4, CG12
-
enumerator kCLOCK_Enc2
CCGR4, CG13
-
enumerator kCLOCK_Enc3
CCGR4, CG14
-
enumerator kCLOCK_Enc4
CCGR4, CG15
-
enumerator kCLOCK_Rom
CCGR5, CG0
-
enumerator kCLOCK_Flexio1
CCGR5, CG1
-
enumerator kCLOCK_Wdog3
CCGR5, CG2
-
enumerator kCLOCK_Dma
CCGR5, CG3
-
enumerator kCLOCK_Kpp
CCGR5, CG4
-
enumerator kCLOCK_Wdog2
CCGR5, CG5
-
enumerator kCLOCK_Aips_tz4
CCGR5, CG6
-
enumerator kCLOCK_Spdif
CCGR5, CG7
-
enumerator kCLOCK_SimMain
CCGR5, CG8
-
enumerator kCLOCK_Sai1
CCGR5, CG9
-
enumerator kCLOCK_Sai2
CCGR5, CG10
-
enumerator kCLOCK_Sai3
CCGR5, CG11
-
enumerator kCLOCK_Lpuart1
CCGR5, CG12
-
enumerator kCLOCK_Lpuart7
CCGR5, CG13
-
enumerator kCLOCK_SnvsHp
CCGR5, CG14
-
enumerator kCLOCK_SnvsLp
CCGR5, CG15
-
enumerator kCLOCK_UsbOh3
CCGR6, CG0
-
enumerator kCLOCK_Usdhc1
CCGR6, CG1
-
enumerator kCLOCK_Usdhc2
CCGR6, CG2
-
enumerator kCLOCK_Dcdc
CCGR6, CG3
-
enumerator kCLOCK_Ipmux4
CCGR6, CG4
-
enumerator kCLOCK_FlexSpi
CCGR6, CG5
-
enumerator kCLOCK_Trng
CCGR6, CG6
-
enumerator kCLOCK_Lpuart8
CCGR6, CG7
-
enumerator kCLOCK_Timer4
CCGR6, CG8
-
enumerator kCLOCK_Aips_tz3
CCGR6, CG9
-
enumerator kCLOCK_SimPer
CCGR6, CG10
-
enumerator kCLOCK_Anadig
CCGR6, CG11
-
enumerator kCLOCK_Lpi2c4
CCGR6, CG12
-
enumerator kCLOCK_Timer1
CCGR6, CG13
-
enumerator kCLOCK_Timer2
CCGR6, CG14
-
enumerator kCLOCK_Timer3
CCGR6, CG15
-
enumerator kCLOCK_IpInvalid
-
enum _clock_osc
OSC 24M sorce select.
Values:
-
enumerator kCLOCK_RcOsc
On chip OSC.
-
enumerator kCLOCK_XtalOsc
24M Xtal OSC
-
enumerator kCLOCK_RcOsc
-
enum _clock_gate_value
Clock gate value.
Values:
-
enumerator kCLOCK_ClockNotNeeded
Clock is off during all modes.
-
enumerator kCLOCK_ClockNeededRun
Clock is on in run mode, but off in WAIT and STOP modes
-
enumerator kCLOCK_ClockNeededRunWait
Clock is on during all modes, except STOP mode
-
enumerator kCLOCK_ClockNotNeeded
-
enum _clock_mode_t
System clock mode.
Values:
-
enumerator kCLOCK_ModeRun
Remain in run mode.
-
enumerator kCLOCK_ModeWait
Transfer to wait mode.
-
enumerator kCLOCK_ModeStop
Transfer to stop mode.
-
enumerator kCLOCK_ModeRun
-
enum _clock_mux
MUX control names for clock mux setting.
These constants define the mux control names for clock mux setting.
0:7: REG offset to CCM_BASE in bytes.
8:15: Root clock setting bit field shift.
16:31: Root clock setting bit field width.
Values:
-
enumerator kCLOCK_Pll3SwMux
pll3_sw_clk mux name
-
enumerator kCLOCK_PeriphMux
periph mux name
-
enumerator kCLOCK_SemcAltMux
semc mux name
-
enumerator kCLOCK_SemcMux
semc mux name
-
enumerator kCLOCK_PrePeriphMux
pre-periph mux name
-
enumerator kCLOCK_TraceMux
trace mux name
-
enumerator kCLOCK_PeriphClk2Mux
periph clock2 mux name
-
enumerator kCLOCK_LpspiMux
lpspi mux name
-
enumerator kCLOCK_FlexspiMux
flexspi mux name
-
enumerator kCLOCK_Usdhc2Mux
usdhc2 mux name
-
enumerator kCLOCK_Usdhc1Mux
usdhc1 mux name
-
enumerator kCLOCK_Sai3Mux
sai3 mux name
-
enumerator kCLOCK_Sai2Mux
sai2 mux name
-
enumerator kCLOCK_Sai1Mux
sai1 mux name
-
enumerator kCLOCK_PerclkMux
perclk mux name
-
enumerator kCLOCK_Flexio2Mux
flexio2 mux name
-
enumerator kCLOCK_CanMux
can mux name
-
enumerator kCLOCK_UartMux
uart mux name
-
enumerator kCLOCK_SpdifMux
spdif mux name
-
enumerator kCLOCK_Flexio1Mux
flexio1 mux name
-
enumerator kCLOCK_Lpi2cMux
lpi2c mux name
-
enumerator kCLOCK_LcdifPreMux
lcdif pre mux name
-
enumerator kCLOCK_CsiMux
csi mux name
-
enum _clock_div
DIV control names for clock div setting.
These constants define div control names for clock div setting.
0:7: REG offset to CCM_BASE in bytes.
8:15: Root clock setting bit field shift.
16:31: Root clock setting bit field width.
Values:
-
enumerator kCLOCK_ArmDiv
core div name
-
enumerator kCLOCK_PeriphClk2Div
periph clock2 div name
-
enumerator kCLOCK_SemcDiv
semc div name
-
enumerator kCLOCK_AhbDiv
ahb div name
-
enumerator kCLOCK_IpgDiv
ipg div name
-
enumerator kCLOCK_LpspiDiv
lpspi div name
-
enumerator kCLOCK_LcdifDiv
lcdif div name
-
enumerator kCLOCK_FlexspiDiv
flexspi div name
-
enumerator kCLOCK_PerclkDiv
perclk div name
-
enumerator kCLOCK_CanDiv
can div name
-
enumerator kCLOCK_TraceDiv
trace div name
-
enumerator kCLOCK_Usdhc2Div
usdhc2 div name
-
enumerator kCLOCK_Usdhc1Div
usdhc1 div name
-
enumerator kCLOCK_UartDiv
uart div name
-
enumerator kCLOCK_Flexio2Div
flexio2 pre div name
-
enumerator kCLOCK_Sai3PreDiv
sai3 pre div name
-
enumerator kCLOCK_Sai3Div
sai3 div name
-
enumerator kCLOCK_Flexio2PreDiv
sai3 pre div name
-
enumerator kCLOCK_Sai1PreDiv
sai1 pre div name
-
enumerator kCLOCK_Sai1Div
sai1 div name
-
enumerator kCLOCK_Sai2PreDiv
sai2 pre div name
-
enumerator kCLOCK_Sai2Div
sai2 div name
-
enumerator kCLOCK_Spdif0PreDiv
spdif pre div name
-
enumerator kCLOCK_Spdif0Div
spdif div name
-
enumerator kCLOCK_Flexio1PreDiv
flexio1 pre div name
-
enumerator kCLOCK_Flexio1Div
flexio1 div name
-
enumerator kCLOCK_Lpi2cDiv
lpi2c div name
-
enumerator kCLOCK_LcdifPreDiv
lcdif pre div name
-
enumerator kCLOCK_CsiDiv
csi div name
-
enumerator kCLOCK_NonePreDiv
None Pre div.
-
enum _clock_div_value
Clock divider value.
Values:
-
enumerator kCLOCK_ArmDivBy1
ARM clock divider set to divided by 1.
-
enumerator kCLOCK_ArmDivBy2
ARM clock divider set to divided by 2.
-
enumerator kCLOCK_ArmDivBy3
ARM clock divider set to divided by 3.
-
enumerator kCLOCK_ArmDivBy4
ARM clock divider set to divided by 4.
-
enumerator kCLOCK_ArmDivBy5
ARM clock divider set to divided by 5.
-
enumerator kCLOCK_ArmDivBy6
ARM clock divider set to divided by 6.
-
enumerator kCLOCK_ArmDivBy7
ARM clock divider set to divided by 7.
-
enumerator kCLOCK_ArmDivBy8
ARM clock divider set to divided by 8.
-
enumerator kCLOCK_PeriphClk2DivBy1
PeriphClk2 divider set to divided by 1.
-
enumerator kCLOCK_PeriphClk2DivBy2
PeriphClk2 divider set to divided by 2.
-
enumerator kCLOCK_PeriphClk2DivBy3
PeriphClk2 divider set to divided by 3.
-
enumerator kCLOCK_PeriphClk2DivBy4
PeriphClk2 divider set to divided by 4.
-
enumerator kCLOCK_PeriphClk2DivBy5
PeriphClk2 divider set to divided by 5.
-
enumerator kCLOCK_PeriphClk2DivBy6
PeriphClk2 divider set to divided by 6.
-
enumerator kCLOCK_PeriphClk2DivBy7
PeriphClk2 divider set to divided by 7.
-
enumerator kCLOCK_PeriphClk2DivBy8
PeriphClk2 divider set to divided by 8.
-
enumerator kCLOCK_SemcDivBy1
SEMC divider set to divided by 1.
-
enumerator kCLOCK_SemcDivBy2
SEMC divider set to divided by 2.
-
enumerator kCLOCK_SemcDivBy3
SEMC divider set to divided by 3.
-
enumerator kCLOCK_SemcDivBy4
SEMC divider set to divided by 4.
-
enumerator kCLOCK_SemcDivBy5
SEMC divider set to divided by 5.
-
enumerator kCLOCK_SemcDivBy6
SEMC divider set to divided by 6.
-
enumerator kCLOCK_SemcDivBy7
SEMC divider set to divided by 7.
-
enumerator kCLOCK_SemcDivBy8
SEMC divider set to divided by 8.
-
enumerator kCLOCK_AhbDivBy1
AHB divider set to divided by 1.
-
enumerator kCLOCK_AhbDivBy2
AHB divider set to divided by 2.
-
enumerator kCLOCK_AhbDivBy3
AHB divider set to divided by 3.
-
enumerator kCLOCK_AhbDivBy4
AHB divider set to divided by 4.
-
enumerator kCLOCK_AhbDivBy5
AHB divider set to divided by 5.
-
enumerator kCLOCK_AhbDivBy6
AHB divider set to divided by 6.
-
enumerator kCLOCK_AhbDivBy7
AHB divider set to divided by 7.
-
enumerator kCLOCK_AhbDivBy8
AHB divider set to divided by 8.
-
enumerator kCLOCK_IpgDivBy1
Ipg divider set to divided by 1.
-
enumerator kCLOCK_IpgDivBy2
Ipg divider set to divided by 2.
-
enumerator kCLOCK_IpgDivBy3
Ipg divider set to divided by 3.
-
enumerator kCLOCK_IpgDivBy4
Ipg divider set to divided by 4.
-
enumerator kCLOCK_LpspiDivBy1
LPSPI divider set to divided by 1.
-
enumerator kCLOCK_LpspiDivBy2
LPSPI divider set to divided by 2.
-
enumerator kCLOCK_LpspiDivBy3
LPSPI divider set to divided by 3.
-
enumerator kCLOCK_LpspiDivBy4
LPSPI divider set to divided by 4.
-
enumerator kCLOCK_LpspiDivBy5
LPSPI divider set to divided by 5.
-
enumerator kCLOCK_LpspiDivBy6
LPSPI divider set to divided by 6.
-
enumerator kCLOCK_LpspiDivBy7
LPSPI divider set to divided by 7.
-
enumerator kCLOCK_LpspiDivBy8
LPSPI divider set to divided by 8.
-
enumerator kCLOCK_LcdifDivBy1
LPDIF divider set to divided by 1.
-
enumerator kCLOCK_LcdifDivBy2
LPDIF divider set to divided by 2.
-
enumerator kCLOCK_LcdifDivBy3
LPDIF divider set to divided by 3.
-
enumerator kCLOCK_LcdifDivBy4
LPDIF divider set to divided by 4.
-
enumerator kCLOCK_LcdifDivBy5
LPDIF divider set to divided by 5.
-
enumerator kCLOCK_LcdifDivBy6
LPDIF divider set to divided by 6.
-
enumerator kCLOCK_LcdifDivBy7
LPDIF divider set to divided by 7.
-
enumerator kCLOCK_LcdifDivBy8
LPDIF divider set to divided by 8.
-
enumerator kCLOCK_FlexspiDivBy1
FLEXSPI divider set to divided by 1.
-
enumerator kCLOCK_FlexspiDivBy2
FLEXSPI divider set to divided by 2.
-
enumerator kCLOCK_FlexspiDivBy3
FLEXSPI divider set to divided by 3.
-
enumerator kCLOCK_FlexspiDivBy4
FLEXSPI divider set to divided by 4.
-
enumerator kCLOCK_FlexspiDivBy5
FLEXSPI divider set to divided by 5.
-
enumerator kCLOCK_FlexspiDivBy6
FLEXSPI divider set to divided by 6.
-
enumerator kCLOCK_FlexspiDivBy7
FLEXSPI divider set to divided by 7.
-
enumerator kCLOCK_FlexspiDivBy8
FLEXSPI divider set to divided by 8.
-
enumerator kCLOCK_TraceDivBy1
TRACE divider set to divided by 1.
-
enumerator kCLOCK_TraceDivBy2
TRACE divider set to divided by 2.
-
enumerator kCLOCK_TraceDivBy3
TRACE divider set to divided by 3.
-
enumerator kCLOCK_TraceDivBy4
TRACE divider set to divided by 4.
-
enumerator kCLOCK_Usdhc2DivBy1
USDHC2 divider set to divided by 1.
-
enumerator kCLOCK_Usdhc2DivBy2
USDHC2 divider set to divided by 2.
-
enumerator kCLOCK_Usdhc2DivBy3
USDHC2 divider set to divided by 3.
-
enumerator kCLOCK_Usdhc2DivBy4
USDHC2 divider set to divided by 4.
-
enumerator kCLOCK_Usdhc2DivBy5
USDHC2 divider set to divided by 5.
-
enumerator kCLOCK_Usdhc2DivBy6
USDHC2 divider set to divided by 6.
-
enumerator kCLOCK_Usdhc2DivBy7
USDHC2 divider set to divided by 7.
-
enumerator kCLOCK_Usdhc2DivBy8
USDHC2 divider set to divided by 8.
-
enumerator kCLOCK_Usdhc1DivBy1
USDHC1 divider set to divided by 1.
-
enumerator kCLOCK_Usdhc1DivBy2
USDHC1 divider set to divided by 2.
-
enumerator kCLOCK_Usdhc1DivBy3
USDHC1 divider set to divided by 3.
-
enumerator kCLOCK_Usdhc1DivBy4
USDHC1 divider set to divided by 4.
-
enumerator kCLOCK_Usdhc1DivBy5
USDHC1 divider set to divided by 5.
-
enumerator kCLOCK_Usdhc1DivBy6
USDHC1 divider set to divided by 6.
-
enumerator kCLOCK_Usdhc1DivBy7
USDHC1 divider set to divided by 7.
-
enumerator kCLOCK_Usdhc1DivBy8
USDHC1 divider set to divided by 8.
-
enumerator kCLOCK_Flexio2DivBy1
Flexio2 divider set to divided by 1.
-
enumerator kCLOCK_Flexio2DivBy2
Flexio2 divider set to divided by 2.
-
enumerator kCLOCK_Flexio2DivBy3
Flexio2 divider set to divided by 3.
-
enumerator kCLOCK_Flexio2DivBy4
Flexio2 divider set to divided by 4.
-
enumerator kCLOCK_Flexio2DivBy5
Flexio2 divider set to divided by 5.
-
enumerator kCLOCK_Flexio2DivBy6
Flexio2 divider set to divided by 6.
-
enumerator kCLOCK_Flexio2DivBy7
Flexio2 divider set to divided by 7.
-
enumerator kCLOCK_Flexio2DivBy8
Flexio2 divider set to divided by 8.
-
enumerator kCLOCK_Sai3PreDivBy1
SAI3ClkPred divider set to divided by 1.
-
enumerator kCLOCK_Sai3PreDivBy2
SAI3ClkPred divider set to divided by 2.
-
enumerator kCLOCK_Sai3PreDivBy3
SAI3ClkPred divider set to divided by 3.
-
enumerator kCLOCK_Sai3PreDivBy4
SAI3ClkPred divider set to divided by 4.
-
enumerator kCLOCK_Sai3PreDivBy5
SAI3ClkPred divider set to divided by 5.
-
enumerator kCLOCK_Sai3PreDivBy6
SAI3ClkPred divider set to divided by 6.
-
enumerator kCLOCK_Sai3PreDivBy7
SAI3ClkPred divider set to divided by 7.
-
enumerator kCLOCK_Sai3PreDivBy8
SAI3ClkPred divider set to divided by 8.
-
enumerator kCLOCK_Flexio2PreDivBy1
Flexio2 pre divider set to divided by 1.
-
enumerator kCLOCK_Flexio2PreDivBy2
Flexio2 pre divider set to divided by 2.
-
enumerator kCLOCK_Flexio2PreDivBy3
Flexio2 pre divider set to divided by 3.
-
enumerator kCLOCK_Flexio2PreDivBy4
Flexio2 pre divider set to divided by 4.
-
enumerator kCLOCK_Flexio2PreDivBy5
Flexio2 pre divider set to divided by 5.
-
enumerator kCLOCK_Flexio2PreDivBy6
Flexio2 pre divider set to divided by 6.
-
enumerator kCLOCK_Flexio2PreDivBy7
Flexio2 pre divider set to divided by 7.
-
enumerator kCLOCK_Flexio2PreDivBy8
Flexio2 pre divider set to divided by 8.
-
enumerator kCLOCK_Sai1PreDivBy1
SAI1 pred divider set to divided by 1.
-
enumerator kCLOCK_Sai1PreDivBy2
SAI1 pred divider set to divided by 2.
-
enumerator kCLOCK_Sai1PreDivBy3
SAI1 pred divider set to divided by 3.
-
enumerator kCLOCK_Sai1PreDivBy4
SAI1 pred divider set to divided by 4.
-
enumerator kCLOCK_Sai1PreDivBy5
SAI1 pred divider set to divided by 5.
-
enumerator kCLOCK_Sai1PreDivBy6
SAI1 pred divider set to divided by 6.
-
enumerator kCLOCK_Sai1PreDivBy7
SAI1 pred divider set to divided by 7.
-
enumerator kCLOCK_Sai1PreDivBy8
SAI1 pred divider set to divided by 8.
-
enumerator kCLOCK_Sai2PreDivBy1
SAI2ClkPred divider set to divided by 1.
-
enumerator kCLOCK_Sai2PreDivBy2
SAI2ClkPred divider set to divided by 2.
-
enumerator kCLOCK_Sai2PreDivBy3
SAI2ClkPred divider set to divided by 3.
-
enumerator kCLOCK_Sai2PreDivBy4
SAI2ClkPred divider set to divided by 4.
-
enumerator kCLOCK_Sai2PreDivBy5
SAI2ClkPred divider set to divided by 5.
-
enumerator kCLOCK_Sai2PreDivBy6
SAI2ClkPred divider set to divided by 6.
-
enumerator kCLOCK_Sai2PreDivBy7
SAI2ClkPred divider set to divided by 7.
-
enumerator kCLOCK_Sai2PreDivBy8
SAI2ClkPred divider set to divided by 8.
-
enumerator kCLOCK_Spdif0PreDivBy1
SPDIF0 pred divider set to divided by 1.
-
enumerator kCLOCK_Spdif0PreDivBy2
SPDIF0 pred divider set to divided by 2.
-
enumerator kCLOCK_Spdif0PreDivBy3
SPDIF0 pred divider set to divided by 3.
-
enumerator kCLOCK_Spdif0PreDivBy4
SPDIF0 pred divider set to divided by 4.
-
enumerator kCLOCK_Spdif0PreDivBy5
SPDIF0 pred divider set to divided by 5.
-
enumerator kCLOCK_Spdif0PreDivBy6
SPDIF0 pred divider set to divided by 6.
-
enumerator kCLOCK_Spdif0PreDivBy7
SPDIF0 pred divider set to divided by 7.
-
enumerator kCLOCK_Spdif0PreDivBy8
SPDIF0 pred divider set to divided by 8.
-
enumerator kCLOCK_Spdif0DivBy1
SPDIF divider set to divided by 1.
-
enumerator kCLOCK_Spdif0DivBy2
SPDIF divider set to divided by 2.
-
enumerator kCLOCK_Spdif0DivBy3
SPDIF divider set to divided by 3.
-
enumerator kCLOCK_Spdif0DivBy4
SPDIF divider set to divided by 4.
-
enumerator kCLOCK_Spdif0DivBy5
SPDIF divider set to divided by 5.
-
enumerator kCLOCK_Spdif0DivBy6
SPDIF divider set to divided by 6.
-
enumerator kCLOCK_Spdif0DivBy7
SPDIF divider set to divided by 7.
-
enumerator kCLOCK_Spdif0DivBy8
SPDIF divider set to divided by 8.
-
enumerator kCLOCK_Flexio1PreDivBy1
Flexio1 pre divider set to divided by 1.
-
enumerator kCLOCK_Flexio1PreDivBy2
Flexio1 pre divider set to divided by 2.
-
enumerator kCLOCK_Flexio1PreDivBy3
Flexio1 pre divider set to divided by 3.
-
enumerator kCLOCK_Flexio1PreDivBy4
Flexio1 pre divider set to divided by 4.
-
enumerator kCLOCK_Flexio1PreDivBy5
Flexio1 pre divider set to divided by 5.
-
enumerator kCLOCK_Flexio1PreDivBy6
Flexio1 pre divider set to divided by 6.
-
enumerator kCLOCK_Flexio1PreDivBy7
Flexio1 pre divider set to divided by 7.
-
enumerator kCLOCK_Flexio1PreDivBy8
Flexio1 pre divider set to divided by 8.
-
enumerator kCLOCK_Flexio1DivBy1
Flexio1 divider set to divided by 1.
-
enumerator kCLOCK_Flexio1DivBy2
Flexio1 divider set to divided by 2.
-
enumerator kCLOCK_Flexio1DivBy3
Flexio1 divider set to divided by 3.
-
enumerator kCLOCK_Flexio1DivBy4
Flexio1 divider set to divided by 4.
-
enumerator kCLOCK_Flexio1DivBy5
Flexio1 divider set to divided by 5.
-
enumerator kCLOCK_Flexio1DivBy6
Flexio1 divider set to divided by 6.
-
enumerator kCLOCK_Flexio1DivBy7
Flexio1 divider set to divided by 7.
-
enumerator kCLOCK_Flexio1DivBy8
Flexio1 divider set to divided by 8.
-
enumerator kCLOCK_LcdifPreDivBy1
Lcdif pre divider set to divided by 1.
-
enumerator kCLOCK_LcdifPreDivBy2
Lcdif pre divider set to divided by 2.
-
enumerator kCLOCK_LcdifPreDivBy3
Lcdif pre divider set to divided by 3.
-
enumerator kCLOCK_LcdifPreDivBy4
Lcdif pre divider set to divided by 4.
-
enumerator kCLOCK_LcdifPreDivBy5
Lcdif pre divider set to divided by 5.
-
enumerator kCLOCK_LcdifPreDivBy6
Lcdif pre divider set to divided by 6.
-
enumerator kCLOCK_LcdifPreDivBy7
Lcdif pre divider set to divided by 7.
-
enumerator kCLOCK_LcdifPreDivBy8
Lcdif pre divider set to divided by 8.
-
enumerator kCLOCK_CsiDivBy1
Csi pre divider set to divided by 1.
-
enumerator kCLOCK_CsiDivBy2
Csi pre divider set to divided by 2.
-
enumerator kCLOCK_CsiDivBy3
Csi pre divider set to divided by 3.
-
enumerator kCLOCK_CsiDivBy4
Csi pre divider set to divided by 4.
-
enumerator kCLOCK_CsiDivBy5
Csi pre divider set to divided by 5.
-
enumerator kCLOCK_CsiDivBy6
Csi pre divider set to divided by 6.
-
enumerator kCLOCK_CsiDivBy7
Csi pre divider set to divided by 7.
-
enumerator kCLOCK_CsiDivBy8
Csi pre divider set to divided by 8.
-
enumerator kCLOCK_MiscDivBy1
Misc divider like LPI2C set to divided by1.
-
enumerator kCLOCK_MiscDivBy2
Misc divider like LPI2C set to divided by2.
-
enumerator kCLOCK_MiscDivBy3
Misc divider like LPI2C set to divided by3.
-
enumerator kCLOCK_MiscDivBy4
Misc divider like LPI2C set to divided by4.
-
enumerator kCLOCK_MiscDivBy5
Misc divider like LPI2C set to divided by5.
-
enumerator kCLOCK_MiscDivBy6
Misc divider like LPI2C set to divided by6.
-
enumerator kCLOCK_MiscDivBy7
Misc divider like LPI2C set to divided by7.
-
enumerator kCLOCK_MiscDivBy8
Misc divider like LPI2C set to divided by8.
-
enumerator kCLOCK_MiscDivBy9
Misc divider like LPI2C set to divided by9.
-
enumerator kCLOCK_MiscDivBy10
Misc divider like LPI2C set to divided by10.
-
enumerator kCLOCK_MiscDivBy11
Misc divider like LPI2C set to divided by11.
-
enumerator kCLOCK_MiscDivBy12
Misc divider like LPI2C set to divided by12.
-
enumerator kCLOCK_MiscDivBy13
Misc divider like LPI2C set to divided by13.
-
enumerator kCLOCK_MiscDivBy14
Misc divider like LPI2C set to divided by14.
-
enumerator kCLOCK_MiscDivBy15
Misc divider like LPI2C set to divided by15.
-
enumerator kCLOCK_MiscDivBy16
Misc divider like LPI2C set to divided by16.
-
enumerator kCLOCK_MiscDivBy17
Misc divider like LPI2C set to divided by17.
-
enumerator kCLOCK_MiscDivBy18
Misc divider like LPI2C set to divided by18.
-
enumerator kCLOCK_MiscDivBy19
Misc divider like LPI2C set to divided by19.
-
enumerator kCLOCK_MiscDivBy20
Misc divider like LPI2C set to divided by20.
-
enumerator kCLOCK_MiscDivBy21
Misc divider like LPI2C set to divided by21.
-
enumerator kCLOCK_MiscDivBy22
Misc divider like LPI2C set to divided by22.
-
enumerator kCLOCK_MiscDivBy23
Misc divider like LPI2C set to divided by23.
-
enumerator kCLOCK_MiscDivBy24
Misc divider like LPI2C set to divided by24.
-
enumerator kCLOCK_MiscDivBy25
Misc divider like LPI2C set to divided by25.
-
enumerator kCLOCK_MiscDivBy26
Misc divider like LPI2C set to divided by26.
-
enumerator kCLOCK_MiscDivBy27
Misc divider like LPI2C set to divided by27.
-
enumerator kCLOCK_MiscDivBy28
Misc divider like LPI2C set to divided by28.
-
enumerator kCLOCK_MiscDivBy29
Misc divider like LPI2C set to divided by29.
-
enumerator kCLOCK_MiscDivBy30
Misc divider like LPI2C set to divided by30.
-
enumerator kCLOCK_MiscDivBy31
Misc divider like LPI2C set to divided by31.
-
enumerator kCLOCK_MiscDivBy32
Misc divider like LPI2C set to divided by32.
-
enumerator kCLOCK_MiscDivBy33
Misc divider like LPI2C set to divided by33.
-
enumerator kCLOCK_MiscDivBy34
Misc divider like LPI2C set to divided by34.
-
enumerator kCLOCK_MiscDivBy35
Misc divider like LPI2C set to divided by35.
-
enumerator kCLOCK_MiscDivBy36
Misc divider like LPI2C set to divided by36.
-
enumerator kCLOCK_MiscDivBy37
Misc divider like LPI2C set to divided by37.
-
enumerator kCLOCK_MiscDivBy38
Misc divider like LPI2C set to divided by38.
-
enumerator kCLOCK_MiscDivBy39
Misc divider like LPI2C set to divided by39.
-
enumerator kCLOCK_MiscDivBy40
Misc divider like LPI2C set to divided by40.
-
enumerator kCLOCK_MiscDivBy41
Misc divider like LPI2C set to divided by41.
-
enumerator kCLOCK_MiscDivBy42
Misc divider like LPI2C set to divided by42.
-
enumerator kCLOCK_MiscDivBy43
Misc divider like LPI2C set to divided by43.
-
enumerator kCLOCK_MiscDivBy44
Misc divider like LPI2C set to divided by44.
-
enumerator kCLOCK_MiscDivBy45
Misc divider like LPI2C set to divided by45.
-
enumerator kCLOCK_MiscDivBy46
Misc divider like LPI2C set to divided by46.
-
enumerator kCLOCK_MiscDivBy47
Misc divider like LPI2C set to divided by47.
-
enumerator kCLOCK_MiscDivBy48
Misc divider like LPI2C set to divided by48.
-
enumerator kCLOCK_MiscDivBy49
Misc divider like LPI2C set to divided by49.
-
enumerator kCLOCK_MiscDivBy50
Misc divider like LPI2C set to divided by50.
-
enumerator kCLOCK_MiscDivBy51
Misc divider like LPI2C set to divided by51.
-
enumerator kCLOCK_MiscDivBy52
Misc divider like LPI2C set to divided by52.
-
enumerator kCLOCK_MiscDivBy53
Misc divider like LPI2C set to divided by53.
-
enumerator kCLOCK_MiscDivBy54
Misc divider like LPI2C set to divided by54.
-
enumerator kCLOCK_MiscDivBy55
Misc divider like LPI2C set to divided by55.
-
enumerator kCLOCK_MiscDivBy56
Misc divider like LPI2C set to divided by56.
-
enumerator kCLOCK_MiscDivBy57
Misc divider like LPI2C set to divided by57.
-
enumerator kCLOCK_MiscDivBy58
Misc divider like LPI2C set to divided by58.
-
enumerator kCLOCK_MiscDivBy59
Misc divider like LPI2C set to divided by59.
-
enumerator kCLOCK_MiscDivBy60
Misc divider like LPI2C set to divided by60.
-
enumerator kCLOCK_MiscDivBy61
Misc divider like LPI2C set to divided by61.
-
enumerator kCLOCK_MiscDivBy62
Misc divider like LPI2C set to divided by62.
-
enumerator kCLOCK_MiscDivBy63
Misc divider like LPI2C set to divided by63.
-
enumerator kCLOCK_MiscDivBy64
Misc divider like LPI2C set to divided by64.
-
enumerator kCLOCK_ArmDivBy1
-
enum _clock_usb_src
USB clock source definition.
Values:
-
enumerator kCLOCK_Usb480M
Use 480M.
-
enumerator kCLOCK_UsbSrcUnused
Used when the function does not care the clock source.
-
enumerator kCLOCK_Usb480M
-
enum _clock_usb_phy_src
Source of the USB HS PHY.
Values:
-
enumerator kCLOCK_Usbphy480M
Use 480M.
-
enumerator kCLOCK_Usbphy480M
-
enum _clock_pll_clk_src
PLL clock source, bypass cloco source also.
Values:
-
enumerator kCLOCK_PllClkSrc24M
Pll clock source 24M
-
enumerator kCLOCK_PllSrcClkPN
Pll clock source CLK1_P and CLK1_N
-
enumerator kCLOCK_PllClkSrc24M
-
enum _clock_pll
PLL name.
Values:
-
enumerator kCLOCK_PllArm
PLL ARM
-
enumerator kCLOCK_PllSys
PLL SYS
-
enumerator kCLOCK_PllUsb1
PLL USB1
-
enumerator kCLOCK_PllAudio
PLL Audio
-
enumerator kCLOCK_PllVideo
PLL Video
-
enumerator kCLOCK_PllEnet
PLL Enet0
-
enumerator kCLOCK_PllEnet25M
PLL Enet1
-
enumerator kCLOCK_PllUsb2
PLL USB2
-
enumerator kCLOCK_PllArm
-
enum _clock_pfd
PLL PFD name.
Values:
-
enumerator kCLOCK_Pfd0
PLL PFD0
-
enumerator kCLOCK_Pfd1
PLL PFD1
-
enumerator kCLOCK_Pfd2
PLL PFD2
-
enumerator kCLOCK_Pfd3
PLL PFD3
-
enumerator kCLOCK_Pfd0
-
enum _clock_output1_selection
The enumerater of clock output1’s clock source, such as USB1 PLL, SYS PLL and so on.
Values:
-
enumerator kCLOCK_OutputPllUsb1
Selects USB1 PLL clock(Divided by 2) output.
-
enumerator kCLOCK_OutputPllSys
Selects SYS PLL clock(Divided by 2) output.
-
enumerator kCLOCK_OutputPllVideo
Selects Video PLL clock(Divided by 2) output.
-
enumerator kCLOCK_OutputSemcClk
Selects semc clock root output.
-
enumerator kCLOCK_OutputLcdifPixClk
Selects Lcdif pix clock root output.
-
enumerator kCLOCK_OutputAhbClk
Selects AHB clock root output.
-
enumerator kCLOCK_OutputIpgClk
Selects IPG clock root output.
-
enumerator kCLOCK_OutputPerClk
Selects PERCLK clock root output.
-
enumerator kCLOCK_OutputCkilSyncClk
Selects Ckil clock root output.
-
enumerator kCLOCK_OutputPll4MainClk
Selects PLL4 main clock output.
-
enumerator kCLOCK_DisableClockOutput1
Disables CLKO1.
-
enumerator kCLOCK_OutputPllUsb1
-
enum _clock_output2_selection
The enumerater of clock output2’s clock source, such as USDHC1 clock root, LPI2C clock root and so on.
Values:
-
enumerator kCLOCK_OutputUsdhc1Clk
Selects USDHC1 clock root output.
-
enumerator kCLOCK_OutputLpi2cClk
Selects LPI2C clock root output.
-
enumerator kCLOCK_OutputCsiClk
Selects CSI clock root output.
-
enumerator kCLOCK_OutputOscClk
Selects OSC output.
-
enumerator kCLOCK_OutputUsdhc2Clk
Selects USDHC2 clock root output.
-
enumerator kCLOCK_OutputSai1Clk
Selects SAI1 clock root output.
-
enumerator kCLOCK_OutputSai2Clk
Selects SAI2 clock root output.
-
enumerator kCLOCK_OutputSai3Clk
Selects SAI3 clock root output.
-
enumerator kCLOCK_OutputCanClk
Selects CAN clock root output.
-
enumerator kCLOCK_OutputFlexspiClk
Selects FLEXSPI clock root output.
-
enumerator kCLOCK_OutputUartClk
Selects UART clock root output.
-
enumerator kCLOCK_OutputSpdif0Clk
Selects SPDIF0 clock root output.
-
enumerator kCLOCK_DisableClockOutput2
Disables CLKO2.
-
enumerator kCLOCK_OutputUsdhc1Clk
-
enum _clock_output_divider
The enumerator of clock output’s divider.
Values:
-
enumerator kCLOCK_DivideBy1
Output clock divided by 1.
-
enumerator kCLOCK_DivideBy2
Output clock divided by 2.
-
enumerator kCLOCK_DivideBy3
Output clock divided by 3.
-
enumerator kCLOCK_DivideBy4
Output clock divided by 4.
-
enumerator kCLOCK_DivideBy5
Output clock divided by 5.
-
enumerator kCLOCK_DivideBy6
Output clock divided by 6.
-
enumerator kCLOCK_DivideBy7
Output clock divided by 7.
-
enumerator kCLOCK_DivideBy8
Output clock divided by 8.
-
enumerator kCLOCK_DivideBy1
-
enum _clock_root
The enumerator of clock root.
Values:
-
enumerator kCLOCK_Usdhc1ClkRoot
USDHC1 clock root.
-
enumerator kCLOCK_Usdhc2ClkRoot
USDHC2 clock root.
-
enumerator kCLOCK_FlexspiClkRoot
FLEXSPI clock root.
-
enumerator kCLOCK_CsiClkRoot
CSI clock root.
-
enumerator kCLOCK_LpspiClkRoot
LPSPI clock root.
-
enumerator kCLOCK_TraceClkRoot
Trace clock root.
-
enumerator kCLOCK_Sai1ClkRoot
SAI1 clock root.
-
enumerator kCLOCK_Sai2ClkRoot
SAI2 clock root.
-
enumerator kCLOCK_Sai3ClkRoot
SAI3 clock root.
-
enumerator kCLOCK_Lpi2cClkRoot
LPI2C clock root.
-
enumerator kCLOCK_CanClkRoot
CAN clock root.
-
enumerator kCLOCK_UartClkRoot
UART clock root.
-
enumerator kCLOCK_LcdifClkRoot
LCD clock root.
-
enumerator kCLOCK_SpdifClkRoot
SPDIF clock root.
-
enumerator kCLOCK_Flexio1ClkRoot
FLEXIO1 clock root.
-
enumerator kCLOCK_Flexio2ClkRoot
FLEXIO2 clock root.
-
enumerator kCLOCK_Usdhc1ClkRoot
-
typedef enum _clock_name clock_name_t
Clock name used to get clock frequency.
-
typedef enum _clock_ip_name clock_ip_name_t
CCM CCGR gate control for each module independently.
-
typedef enum _clock_osc clock_osc_t
OSC 24M sorce select.
-
typedef enum _clock_gate_value clock_gate_value_t
Clock gate value.
-
typedef enum _clock_mode_t clock_mode_t
System clock mode.
-
typedef enum _clock_mux clock_mux_t
MUX control names for clock mux setting.
These constants define the mux control names for clock mux setting.
0:7: REG offset to CCM_BASE in bytes.
8:15: Root clock setting bit field shift.
16:31: Root clock setting bit field width.
-
typedef enum _clock_div clock_div_t
DIV control names for clock div setting.
These constants define div control names for clock div setting.
0:7: REG offset to CCM_BASE in bytes.
8:15: Root clock setting bit field shift.
16:31: Root clock setting bit field width.
-
typedef enum _clock_div_value clock_div_value_t
Clock divider value.
-
typedef enum _clock_usb_src clock_usb_src_t
USB clock source definition.
-
typedef enum _clock_usb_phy_src clock_usb_phy_src_t
Source of the USB HS PHY.
-
typedef struct _clock_arm_pll_config clock_arm_pll_config_t
PLL configuration for ARM.
-
typedef struct _clock_usb_pll_config clock_usb_pll_config_t
PLL configuration for USB.
-
typedef struct _clock_sys_pll_config clock_sys_pll_config_t
PLL configuration for System.
-
typedef struct _clock_audio_pll_config clock_audio_pll_config_t
PLL configuration for AUDIO and VIDEO.
-
typedef struct _clock_video_pll_config clock_video_pll_config_t
PLL configuration for AUDIO and VIDEO.
-
typedef struct _clock_enet_pll_config clock_enet_pll_config_t
PLL configuration for ENET.
-
typedef enum _clock_pll clock_pll_t
PLL name.
-
typedef enum _clock_pfd clock_pfd_t
PLL PFD name.
-
typedef enum _clock_output1_selection clock_output1_selection_t
The enumerater of clock output1’s clock source, such as USB1 PLL, SYS PLL and so on.
-
typedef enum _clock_output2_selection clock_output2_selection_t
The enumerater of clock output2’s clock source, such as USDHC1 clock root, LPI2C clock root and so on.
-
typedef enum _clock_output_divider clock_output_divider_t
The enumerator of clock output’s divider.
-
typedef enum _clock_root clock_root_t
The enumerator of clock root.
-
volatile uint32_t g_xtalFreq
External XTAL (24M OSC/SYSOSC) clock frequency.
The XTAL (24M OSC/SYSOSC) clock frequency in Hz, when the clock is setup, use the function CLOCK_SetXtalFreq to set the value in to clock driver. For example, if XTAL is 24MHz,
CLOCK_InitExternalClk(false); CLOCK_SetXtalFreq(240000000);
-
volatile uint32_t g_rtcXtalFreq
External RTC XTAL (32K OSC) clock frequency.
The RTC XTAL (32K OSC) clock frequency in Hz, when the clock is setup, use the function CLOCK_SetRtcXtalFreq to set the value in to clock driver.
-
static inline void CLOCK_SetMux(clock_mux_t mux, uint32_t value)
Set CCM MUX node to certain value.
- Parameters:
mux – Which mux node to set, see clock_mux_t.
value – Clock mux value to set, different mux has different value range.
-
static inline uint32_t CLOCK_GetMux(clock_mux_t mux)
Get CCM MUX value.
- Parameters:
mux – Which mux node to get, see clock_mux_t.
- Returns:
Clock mux value.
-
static inline void CLOCK_SetDiv(clock_div_t divider, uint32_t value)
Set clock divider value.
Example, set the ARM clock divider to divide by 2:
CLOCK_SetDiv(kCLOCK_ArmDiv, kCLOCK_ArmDivBy2);
Example, set the LPI2C clock divider to divide by 5.
CLOCK_SetDiv(kCLOCK_Lpi2cDiv, kCLOCK_MiscDivBy5);
Only kCLOCK_Lpi2cDiv, kCLOCK_CanDiv, kCLOCK_UartDiv, kCLOCK_Sai1Div, kCLOCK_Sai2Div, kCLOCK_Sai3Div , kCLOCK_PerclkDiv can use the divider kCLOCK_MiscDivByxxx.
- Parameters:
divider – Which divider node to set.
value – Clock div value to set, different divider has different value range. See clock_div_value_t for details. Divided clock frequency = Undivided clock frequency / (value + 1)
-
static inline uint32_t CLOCK_GetDiv(clock_div_t divider)
Get CCM DIV node value.
- Parameters:
divider – Which div node to get, see clock_div_t.
-
static inline void CLOCK_ControlGate(clock_ip_name_t name, clock_gate_value_t value)
Control the clock gate for specific IP.
- Parameters:
name – Which clock to enable, see clock_ip_name_t.
value – Clock gate value to set, see clock_gate_value_t.
-
static inline void CLOCK_EnableClock(clock_ip_name_t name)
Enable the clock for specific IP.
- Parameters:
name – Which clock to enable, see clock_ip_name_t.
-
static inline void CLOCK_DisableClock(clock_ip_name_t name)
Disable the clock for specific IP.
- Parameters:
name – Which clock to disable, see clock_ip_name_t.
-
static inline void CLOCK_SetMode(clock_mode_t mode)
Setting the low power mode that system will enter on next assertion of dsm_request signal.
- Parameters:
mode – Which mode to enter, see clock_mode_t.
-
static inline uint32_t CLOCK_GetOscFreq(void)
Gets the OSC clock frequency.
This function will return the external XTAL OSC frequency if it is selected as the source of OSC, otherwise internal 24MHz RC OSC frequency will be returned.
- Returns:
Clock frequency; If the clock is invalid, returns 0.
-
uint32_t CLOCK_GetAhbFreq(void)
Gets the AHB clock frequency.
- Returns:
The AHB clock frequency value in hertz.
-
uint32_t CLOCK_GetSemcFreq(void)
Gets the SEMC clock frequency.
- Returns:
The SEMC clock frequency value in hertz.
-
uint32_t CLOCK_GetIpgFreq(void)
Gets the IPG clock frequency.
- Returns:
The IPG clock frequency value in hertz.
-
uint32_t CLOCK_GetPerClkFreq(void)
Gets the PER clock frequency.
- Returns:
The PER clock frequency value in hertz.
-
uint32_t CLOCK_GetFreq(clock_name_t name)
Gets the clock frequency for a specific clock name.
This function checks the current clock configurations and then calculates the clock frequency for a specific clock name defined in clock_name_t.
- Parameters:
name – Clock names defined in clock_name_t
- Returns:
Clock frequency value in hertz
-
static inline uint32_t CLOCK_GetCpuClkFreq(void)
Get the CCM CPU/core/system frequency.
- Returns:
Clock frequency; If the clock is invalid, returns 0.
-
uint32_t CLOCK_GetClockRootFreq(clock_root_t clockRoot)
Gets the frequency of selected clock root.
- Parameters:
clockRoot – The clock root used to get the frequency, please refer to clock_root_t.
- Returns:
The frequency of selected clock root.
-
FSL_CLOCK_DRIVER_VERSION
CLOCK driver version 2.5.3.
-
SDK_DEVICE_MAXIMUM_CPU_CLOCK_FREQUENCY
-
CCM_ANALOG_PLL_BYPASS_SHIFT
-
CCM_ANALOG_PLL_BYPASS_CLK_SRC_MASK
-
CCM_ANALOG_PLL_BYPASS_CLK_SRC_SHIFT
-
CCSR_OFFSET
CCM registers offset.
-
CBCDR_OFFSET
-
CBCMR_OFFSET
-
CSCMR1_OFFSET
-
CSCMR2_OFFSET
-
CSCDR1_OFFSET
-
CDCDR_OFFSET
-
CSCDR2_OFFSET
-
CSCDR3_OFFSET
-
CACRR_OFFSET
-
CS1CDR_OFFSET
-
CS2CDR_OFFSET
-
PLL_ARM_OFFSET
CCM Analog registers offset.
-
PLL_SYS_OFFSET
-
PLL_USB1_OFFSET
-
PLL_AUDIO_OFFSET
-
PLL_VIDEO_OFFSET
-
PLL_ENET_OFFSET
-
PLL_USB2_OFFSET
-
CCM_TUPLE(reg, shift, mask, busyShift)
-
CCM_TUPLE_REG(base, tuple)
-
CCM_TUPLE_SHIFT(tuple)
-
CCM_TUPLE_MASK(tuple)
-
CCM_TUPLE_BUSY_SHIFT(tuple)
-
CCM_NO_BUSY_WAIT
-
CCM_ANALOG_TUPLE(reg, shift)
CCM ANALOG tuple macros to map corresponding registers and bit fields.
-
CCM_ANALOG_TUPLE_SHIFT(tuple)
-
CCM_ANALOG_TUPLE_REG_OFF(base, tuple, off)
-
CCM_ANALOG_TUPLE_REG(base, tuple)
-
CAN_CLOCK_CHECK_NO_AFFECTS
-
CLKPN_FREQ
clock1PN frequency.
-
CLOCK_SetXtal0Freq
-
CLOCK_SetXtal32Freq
-
ADC_CLOCKS
Clock ip name array for ADC.
-
AOI_CLOCKS
Clock ip name array for AOI.
-
BEE_CLOCKS
Clock ip name array for BEE.
-
CMP_CLOCKS
Clock ip name array for CMP.
-
CSI_CLOCKS
Clock ip name array for CSI.
-
DCDC_CLOCKS
Clock ip name array for DCDC.
-
DCP_CLOCKS
Clock ip name array for DCP.
-
DMAMUX_CLOCKS
Clock ip name array for DMAMUX_CLOCKS.
-
EDMA_CLOCKS
Clock ip name array for DMA.
-
ENC_CLOCKS
Clock ip name array for ENC.
-
ENET_CLOCKS
Clock ip name array for ENET.
-
EWM_CLOCKS
Clock ip name array for EWM.
-
FLEXCAN_CLOCKS
Clock ip name array for FLEXCAN.
-
FLEXCAN_PERIPH_CLOCKS
Clock ip name array for FLEXCAN Peripheral clock.
-
FLEXIO_CLOCKS
Clock ip name array for FLEXIO.
-
FLEXRAM_CLOCKS
Clock ip name array for FLEXRAM.
-
FLEXSPI_CLOCKS
Clock ip name array for FLEXSPI.
-
FLEXSPI_EXSC_CLOCKS
Clock ip name array for FLEXSPI EXSC.
-
GPIO_CLOCKS
Clock ip name array for GPIO.
-
GPT_CLOCKS
Clock ip name array for GPT.
-
KPP_CLOCKS
Clock ip name array for KPP.
-
LCDIF_CLOCKS
Clock ip name array for LCDIF.
-
LCDIF_PERIPH_CLOCKS
Clock ip name array for LCDIF PIXEL.
-
LPI2C_CLOCKS
Clock ip name array for LPI2C.
-
LPSPI_CLOCKS
Clock ip name array for LPSPI.
-
LPUART_CLOCKS
Clock ip name array for LPUART.
-
MQS_CLOCKS
Clock ip name array for MQS.
-
OCRAM_EXSC_CLOCKS
Clock ip name array for OCRAM EXSC.
-
PIT_CLOCKS
Clock ip name array for PIT.
-
PWM_CLOCKS
Clock ip name array for PWM.
-
PXP_CLOCKS
Clock ip name array for PXP.
-
RTWDOG_CLOCKS
Clock ip name array for RTWDOG.
-
SAI_CLOCKS
Clock ip name array for SAI.
-
SEMC_CLOCKS
Clock ip name array for SEMC.
-
SEMC_EXSC_CLOCKS
Clock ip name array for SEMC EXSC.
-
TMR_CLOCKS
Clock ip name array for QTIMER.
-
TRNG_CLOCKS
Clock ip name array for TRNG.
-
TSC_CLOCKS
Clock ip name array for TSC.
-
WDOG_CLOCKS
Clock ip name array for WDOG.
-
USDHC_CLOCKS
Clock ip name array for USDHC.
-
SPDIF_CLOCKS
Clock ip name array for SPDIF.
-
XBARA_CLOCKS
Clock ip name array for XBARA.
-
XBARB_CLOCKS
Clock ip name array for XBARB.
-
CLOCK_SOURCE_NONE
-
CLOCK_ROOT_SOUCE
-
CLOCK_ROOT_MUX_TUPLE
-
CLOCK_ROOT_NONE_PRE_DIV
-
CLOCK_ROOT_DIV_TUPLE
-
kCLOCK_CoreSysClk
For compatible with other platforms without CCM.
-
CLOCK_GetCoreSysClkFreq
For compatible with other platforms without CCM.
-
void CLOCK_InitExternalClk(bool bypassXtalOsc)
Initialize the external 24MHz clock.
This function supports two modes:
Use external crystal oscillator.
Bypass the external crystal oscillator, using input source clock directly.
After this function, please call CLOCK_SetXtal0Freq to inform clock driver the external clock frequency.
Note
This device does not support bypass external crystal oscillator, so the input parameter should always be false.
- Parameters:
bypassXtalOsc – Pass in true to bypass the external crystal oscillator.
-
void CLOCK_DeinitExternalClk(void)
Deinitialize the external 24MHz clock.
This function disables the external 24MHz clock.
After this function, please call CLOCK_SetXtal0Freq to set external clock frequency to 0.
-
void CLOCK_SwitchOsc(clock_osc_t osc)
Switch the OSC.
This function switches the OSC source for SoC.
- Parameters:
osc – OSC source to switch to.
-
static inline uint32_t CLOCK_GetRtcFreq(void)
Gets the RTC clock frequency.
- Returns:
Clock frequency; If the clock is invalid, returns 0.
-
static inline void CLOCK_SetXtalFreq(uint32_t freq)
Set the XTAL (24M OSC) frequency based on board setting.
- Parameters:
freq – The XTAL input clock frequency in Hz.
-
static inline void CLOCK_SetRtcXtalFreq(uint32_t freq)
Set the RTC XTAL (32K OSC) frequency based on board setting.
- Parameters:
freq – The RTC XTAL input clock frequency in Hz.
-
void CLOCK_InitRcOsc24M(void)
Initialize the RC oscillator 24MHz clock.
-
void CLOCK_DeinitRcOsc24M(void)
Power down the RCOSC 24M clock.
-
bool CLOCK_EnableUsbhs0Clock(clock_usb_src_t src, uint32_t freq)
Enable USB HS clock.
This function only enables the access to USB HS prepheral, upper layer should first call the CLOCK_EnableUsbhs0PhyPllClock to enable the PHY clock to use USB HS.
- Parameters:
src – USB HS does not care about the clock source, here must be kCLOCK_UsbSrcUnused.
freq – USB HS does not care about the clock source, so this parameter is ignored.
- Return values:
true – The clock is set successfully.
false – The clock source is invalid to get proper USB HS clock.
-
bool CLOCK_EnableUsbhs1Clock(clock_usb_src_t src, uint32_t freq)
Enable USB HS clock.
This function only enables the access to USB HS prepheral, upper layer should first call the CLOCK_EnableUsbhs0PhyPllClock to enable the PHY clock to use USB HS.
- Parameters:
src – USB HS does not care about the clock source, here must be kCLOCK_UsbSrcUnused.
freq – USB HS does not care about the clock source, so this parameter is ignored.
- Return values:
true – The clock is set successfully.
false – The clock source is invalid to get proper USB HS clock.
-
static inline void CLOCK_SetPllBypass(CCM_ANALOG_Type *base, clock_pll_t pll, bool bypass)
PLL bypass setting.
- Parameters:
base – CCM_ANALOG base pointer.
pll – PLL control name (see ccm_analog_pll_control_t enumeration)
bypass – Bypass the PLL.
true: Bypass the PLL.
false:Not bypass the PLL.
-
static inline bool CLOCK_IsPllBypassed(CCM_ANALOG_Type *base, clock_pll_t pll)
Check if PLL is bypassed.
- Parameters:
base – CCM_ANALOG base pointer.
pll – PLL control name (see ccm_analog_pll_control_t enumeration)
- Returns:
PLL bypass status.
true: The PLL is bypassed.
false: The PLL is not bypassed.
-
static inline bool CLOCK_IsPllEnabled(CCM_ANALOG_Type *base, clock_pll_t pll)
Check if PLL is enabled.
- Parameters:
base – CCM_ANALOG base pointer.
pll – PLL control name (see ccm_analog_pll_control_t enumeration)
- Returns:
PLL bypass status.
true: The PLL is enabled.
false: The PLL is not enabled.
-
static inline void CLOCK_SetPllBypassRefClkSrc(CCM_ANALOG_Type *base, clock_pll_t pll, uint32_t src)
PLL bypass clock source setting. Note: change the bypass clock source also change the pll reference clock source.
- Parameters:
base – CCM_ANALOG base pointer.
pll – PLL control name (see ccm_analog_pll_control_t enumeration)
src – Bypass clock source, reference _clock_pll_bypass_clk_src.
-
static inline uint32_t CLOCK_GetPllBypassRefClk(CCM_ANALOG_Type *base, clock_pll_t pll)
Get PLL bypass clock value, it is PLL reference clock actually. If CLOCK1_P,CLOCK1_N is choose as the pll bypass clock source, please implement the CLKPN_FREQ define, otherwise 0 will be returned.
- Parameters:
base – CCM_ANALOG base pointer.
pll – PLL control name (see ccm_analog_pll_control_t enumeration)
- Return values:
bypass – reference clock frequency value.
-
void CLOCK_InitArmPll(const clock_arm_pll_config_t *config)
Initialize the ARM PLL.
This function initialize the ARM PLL with specific settings
- Parameters:
config – configuration to set to PLL.
-
void CLOCK_DeinitArmPll(void)
De-initialize the ARM PLL.
-
void CLOCK_InitSysPll(const clock_sys_pll_config_t *config)
Initialize the System PLL.
This function initializes the System PLL with specific settings
- Parameters:
config – Configuration to set to PLL.
-
void CLOCK_DeinitSysPll(void)
De-initialize the System PLL.
-
void CLOCK_InitUsb1Pll(const clock_usb_pll_config_t *config)
Initialize the USB1 PLL.
This function initializes the USB1 PLL with specific settings
- Parameters:
config – Configuration to set to PLL.
-
void CLOCK_DeinitUsb1Pll(void)
Deinitialize the USB1 PLL.
-
void CLOCK_InitUsb2Pll(const clock_usb_pll_config_t *config)
Initialize the USB2 PLL.
This function initializes the USB2 PLL with specific settings
- Parameters:
config – Configuration to set to PLL.
-
void CLOCK_DeinitUsb2Pll(void)
Deinitialize the USB2 PLL.
-
void CLOCK_InitAudioPll(const clock_audio_pll_config_t *config)
Initializes the Audio PLL.
This function initializes the Audio PLL with specific settings
- Parameters:
config – Configuration to set to PLL.
-
void CLOCK_DeinitAudioPll(void)
De-initialize the Audio PLL.
-
void CLOCK_InitVideoPll(const clock_video_pll_config_t *config)
Initialize the video PLL.
This function configures the Video PLL with specific settings
- Parameters:
config – configuration to set to PLL.
-
void CLOCK_DeinitVideoPll(void)
De-initialize the Video PLL.
-
void CLOCK_InitEnetPll(const clock_enet_pll_config_t *config)
Initialize the ENET PLL.
This function initializes the ENET PLL with specific settings.
- Parameters:
config – Configuration to set to PLL.
-
void CLOCK_DeinitEnetPll(void)
Deinitialize the ENET PLL.
This function disables the ENET PLL.
-
uint32_t CLOCK_GetPllFreq(clock_pll_t pll)
Get current PLL output frequency.
This function get current output frequency of specific PLL
- Parameters:
pll – pll name to get frequency.
- Returns:
The PLL output frequency in hertz.
-
void CLOCK_InitSysPfd(clock_pfd_t pfd, uint8_t pfdFrac)
Initialize the System PLL PFD.
This function initializes the System PLL PFD. During new value setting, the clock output is disabled to prevent glitch.
Note
It is recommended that PFD settings are kept between 12-35.
- Parameters:
pfd – Which PFD clock to enable.
pfdFrac – The PFD FRAC value.
-
void CLOCK_DeinitSysPfd(clock_pfd_t pfd)
De-initialize the System PLL PFD.
This function disables the System PLL PFD.
- Parameters:
pfd – Which PFD clock to disable.
-
bool CLOCK_IsSysPfdEnabled(clock_pfd_t pfd)
Check if Sys PFD is enabled.
- Parameters:
pfd – PFD control name
- Returns:
PFD bypass status.
true: power on.
false: power off.
-
void CLOCK_InitUsb1Pfd(clock_pfd_t pfd, uint8_t pfdFrac)
Initialize the USB1 PLL PFD.
This function initializes the USB1 PLL PFD. During new value setting, the clock output is disabled to prevent glitch.
Note
It is recommended that PFD settings are kept between 12-35.
- Parameters:
pfd – Which PFD clock to enable.
pfdFrac – The PFD FRAC value.
-
void CLOCK_DeinitUsb1Pfd(clock_pfd_t pfd)
De-initialize the USB1 PLL PFD.
This function disables the USB1 PLL PFD.
- Parameters:
pfd – Which PFD clock to disable.
-
bool CLOCK_IsUsb1PfdEnabled(clock_pfd_t pfd)
Check if Usb1 PFD is enabled.
- Parameters:
pfd – PFD control name.
- Returns:
PFD bypass status.
true: power on.
false: power off.
-
uint32_t CLOCK_GetSysPfdFreq(clock_pfd_t pfd)
Get current System PLL PFD output frequency.
This function get current output frequency of specific System PLL PFD
- Parameters:
pfd – pfd name to get frequency.
- Returns:
The PFD output frequency in hertz.
-
uint32_t CLOCK_GetUsb1PfdFreq(clock_pfd_t pfd)
Get current USB1 PLL PFD output frequency.
This function get current output frequency of specific USB1 PLL PFD
- Parameters:
pfd – pfd name to get frequency.
- Returns:
The PFD output frequency in hertz.
-
bool CLOCK_EnableUsbhs0PhyPllClock(clock_usb_phy_src_t src, uint32_t freq)
Enable USB HS PHY PLL clock.
This function enables the internal 480MHz USB PHY PLL clock.
- Parameters:
src – USB HS PHY PLL clock source.
freq – The frequency specified by src.
- Return values:
true – The clock is set successfully.
false – The clock source is invalid to get proper USB HS clock.
-
void CLOCK_DisableUsbhs0PhyPllClock(void)
Disable USB HS PHY PLL clock.
This function disables USB HS PHY PLL clock.
-
bool CLOCK_EnableUsbhs1PhyPllClock(clock_usb_phy_src_t src, uint32_t freq)
Enable USB HS PHY PLL clock.
This function enables the internal 480MHz USB PHY PLL clock.
- Parameters:
src – USB HS PHY PLL clock source.
freq – The frequency specified by src.
- Return values:
true – The clock is set successfully.
false – The clock source is invalid to get proper USB HS clock.
-
void CLOCK_DisableUsbhs1PhyPllClock(void)
Disable USB HS PHY PLL clock.
This function disables USB HS PHY PLL clock.
-
void CLOCK_SetClockOutput1(clock_output1_selection_t selection, clock_output_divider_t divider)
Set the clock source and the divider of the clock output1.
- Parameters:
selection – The clock source to be output, please refer to clock_output1_selection_t.
divider – The divider of the output clock signal, please refer to clock_output_divider_t.
-
void CLOCK_SetClockOutput2(clock_output2_selection_t selection, clock_output_divider_t divider)
Set the clock source and the divider of the clock output2.
- Parameters:
selection – The clock source to be output, please refer to clock_output2_selection_t.
divider – The divider of the output clock signal, please refer to clock_output_divider_t.
-
uint32_t CLOCK_GetClockOutCLKO1Freq(void)
Get the frequency of clock output1 clock signal.
- Returns:
The frequency of clock output1 clock signal.
-
uint32_t CLOCK_GetClockOutClkO2Freq(void)
Get the frequency of clock output2 clock signal.
- Returns:
The frequency of clock output2 clock signal.
-
FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL
Configure whether driver controls clock.
When set to 0, peripheral drivers will enable clock in initialize function and disable clock in de-initialize function. When set to 1, peripheral driver will not control the clock, application could control the clock out of the driver.
Note
All drivers share this feature switcher. If it is set to 1, application should handle clock enable and disable for all drivers.
-
struct _clock_arm_pll_config
- #include <fsl_clock.h>
PLL configuration for ARM.
Public Members
-
uint32_t loopDivider
PLL loop divider. Valid range for divider value: 54-108. Fout=Fin*loopDivider/2.
-
uint8_t src
Pll clock source, reference _clock_pll_clk_src
-
uint32_t loopDivider
-
struct _clock_usb_pll_config
- #include <fsl_clock.h>
PLL configuration for USB.
Public Members
-
uint8_t loopDivider
PLL loop divider. 0 - Fout=Fref*20; 1 - Fout=Fref*22
-
uint8_t src
Pll clock source, reference _clock_pll_clk_src
-
uint8_t loopDivider
-
struct _clock_sys_pll_config
- #include <fsl_clock.h>
PLL configuration for System.
Public Members
-
uint8_t loopDivider
PLL loop divider. Intended to be 1 (528M). 0 - Fout=Fref*20; 1 - Fout=Fref*22
-
uint32_t numerator
30 bit numerator of fractional loop divider.
-
uint32_t denominator
30 bit denominator of fractional loop divider
-
uint8_t src
Pll clock source, reference _clock_pll_clk_src
-
uint16_t ss_stop
Stop value to get frequency change.
-
uint8_t ss_enable
Enable spread spectrum modulation
-
uint16_t ss_step
Step value to get frequency change step.
-
uint8_t loopDivider
-
struct _clock_audio_pll_config
- #include <fsl_clock.h>
PLL configuration for AUDIO and VIDEO.
Public Members
-
uint8_t loopDivider
PLL loop divider. Valid range for DIV_SELECT divider value: 27~54.
-
uint8_t postDivider
Divider after the PLL, should only be 1, 2, 4, 8, 16.
-
uint32_t numerator
30 bit numerator of fractional loop divider.
-
uint32_t denominator
30 bit denominator of fractional loop divider
-
uint8_t src
Pll clock source, reference _clock_pll_clk_src
-
uint8_t loopDivider
-
struct _clock_video_pll_config
- #include <fsl_clock.h>
PLL configuration for AUDIO and VIDEO.
Public Members
-
uint8_t loopDivider
PLL loop divider. Valid range for DIV_SELECT divider value: 27~54.
-
uint8_t postDivider
Divider after the PLL, should only be 1, 2, 4, 8, 16.
-
uint32_t numerator
30 bit numerator of fractional loop divider.
-
uint32_t denominator
30 bit denominator of fractional loop divider
-
uint8_t src
Pll clock source, reference _clock_pll_clk_src
-
uint8_t loopDivider
-
struct _clock_enet_pll_config
- #include <fsl_clock.h>
PLL configuration for ENET.
Public Members
-
bool enableClkOutput
Power on and enable PLL clock output for ENET0 (ref_enetpll0).
-
bool enableClkOutput25M
Power on and enable PLL clock output for ENET1 (ref_enetpll1).
-
uint8_t loopDivider
Controls the frequency of the ENET0 reference clock. b00 25MHz b01 50MHz b10 100MHz (not 50% duty cycle) b11 125MHz
-
uint8_t src
Pll clock source, reference _clock_pll_clk_src
-
bool enableClkOutput
CMP: Analog Comparator Driver
-
void CMP_Init(CMP_Type *base, const cmp_config_t *config)
Initializes the CMP.
This function initializes the CMP module. The operations included are as follows.
Enabling the clock for CMP module.
Configuring the comparator.
Enabling the CMP module. Note that for some devices, multiple CMP instances share the same clock gate. In this case, to enable the clock for any instance enables all CMPs. See the appropriate MCU reference manual for the clock assignment of the CMP.
- Parameters:
base – CMP peripheral base address.
config – Pointer to the configuration structure.
-
void CMP_Deinit(CMP_Type *base)
De-initializes the CMP module.
This function de-initializes the CMP module. The operations included are as follows.
Disabling the CMP module.
Disabling the clock for CMP module.
This function disables the clock for the CMP. Note that for some devices, multiple CMP instances share the same clock gate. In this case, before disabling the clock for the CMP, ensure that all the CMP instances are not used.
- Parameters:
base – CMP peripheral base address.
-
static inline void CMP_Enable(CMP_Type *base, bool enable)
Enables/disables the CMP module.
- Parameters:
base – CMP peripheral base address.
enable – Enables or disables the module.
-
void CMP_GetDefaultConfig(cmp_config_t *config)
Initializes the CMP user configuration structure.
This function initializes the user configuration structure to these default values.
config->enableCmp = true; config->hysteresisMode = kCMP_HysteresisLevel0; config->enableHighSpeed = false; config->enableInvertOutput = false; config->useUnfilteredOutput = false; config->enablePinOut = false; config->enableTriggerMode = false;
- Parameters:
config – Pointer to the configuration structure.
-
void CMP_SetInputChannels(CMP_Type *base, uint8_t positiveChannel, uint8_t negativeChannel)
Sets the input channels for the comparator.
This function sets the input channels for the comparator. Note that two input channels cannot be set the same way in the application. When the user selects the same input from the analog mux to the positive and negative port, the comparator is disabled automatically.
- Parameters:
base – CMP peripheral base address.
positiveChannel – Positive side input channel number. Available range is 0-7.
negativeChannel – Negative side input channel number. Available range is 0-7.
-
void CMP_EnableDMA(CMP_Type *base, bool enable)
Enables/disables the DMA request for rising/falling events.
This function enables/disables the DMA request for rising/falling events. Either event triggers the generation of the DMA request from CMP if the DMA feature is enabled. Both events are ignored for generating the DMA request from the CMP if the DMA is disabled.
- Parameters:
base – CMP peripheral base address.
enable – Enables or disables the feature.
-
static inline void CMP_EnableWindowMode(CMP_Type *base, bool enable)
Enables/disables the window mode.
- Parameters:
base – CMP peripheral base address.
enable – Enables or disables the feature.
-
static inline void CMP_EnablePassThroughMode(CMP_Type *base, bool enable)
Enables/disables the pass through mode.
- Parameters:
base – CMP peripheral base address.
enable – Enables or disables the feature.
-
void CMP_SetFilterConfig(CMP_Type *base, const cmp_filter_config_t *config)
Configures the filter.
- Parameters:
base – CMP peripheral base address.
config – Pointer to the configuration structure.
-
void CMP_SetDACConfig(CMP_Type *base, const cmp_dac_config_t *config)
Configures the internal DAC.
- Parameters:
base – CMP peripheral base address.
config – Pointer to the configuration structure. “NULL” disables the feature.
-
void CMP_EnableInterrupts(CMP_Type *base, uint32_t mask)
Enables the interrupts.
- Parameters:
base – CMP peripheral base address.
mask – Mask value for interrupts. See “_cmp_interrupt_enable”.
-
void CMP_DisableInterrupts(CMP_Type *base, uint32_t mask)
Disables the interrupts.
- Parameters:
base – CMP peripheral base address.
mask – Mask value for interrupts. See “_cmp_interrupt_enable”.
-
uint32_t CMP_GetStatusFlags(CMP_Type *base)
Gets the status flags.
- Parameters:
base – CMP peripheral base address.
- Returns:
Mask value for the asserted flags. See “_cmp_status_flags”.
-
void CMP_ClearStatusFlags(CMP_Type *base, uint32_t mask)
Clears the status flags.
- Parameters:
base – CMP peripheral base address.
mask – Mask value for the flags. See “_cmp_status_flags”.
-
FSL_CMP_DRIVER_VERSION
CMP driver version 2.0.3.
-
enum _cmp_interrupt_enable
Interrupt enable/disable mask.
Values:
-
enumerator kCMP_OutputRisingInterruptEnable
Comparator interrupt enable rising.
-
enumerator kCMP_OutputFallingInterruptEnable
Comparator interrupt enable falling.
-
enumerator kCMP_OutputRisingInterruptEnable
-
enum _cmp_status_flags
Status flags’ mask.
Values:
-
enumerator kCMP_OutputRisingEventFlag
Rising-edge on the comparison output has occurred.
-
enumerator kCMP_OutputFallingEventFlag
Falling-edge on the comparison output has occurred.
-
enumerator kCMP_OutputAssertEventFlag
Return the current value of the analog comparator output.
-
enumerator kCMP_OutputRisingEventFlag
-
enum _cmp_hysteresis_mode
CMP Hysteresis mode.
Values:
-
enumerator kCMP_HysteresisLevel0
Hysteresis level 0.
-
enumerator kCMP_HysteresisLevel1
Hysteresis level 1.
-
enumerator kCMP_HysteresisLevel2
Hysteresis level 2.
-
enumerator kCMP_HysteresisLevel3
Hysteresis level 3.
-
enumerator kCMP_HysteresisLevel0
-
enum _cmp_reference_voltage_source
CMP Voltage Reference source.
Values:
-
enumerator kCMP_VrefSourceVin1
Vin1 is selected as a resistor ladder network supply reference Vin.
-
enumerator kCMP_VrefSourceVin2
Vin2 is selected as a resistor ladder network supply reference Vin.
-
enumerator kCMP_VrefSourceVin1
-
typedef enum _cmp_hysteresis_mode cmp_hysteresis_mode_t
CMP Hysteresis mode.
-
typedef enum _cmp_reference_voltage_source cmp_reference_voltage_source_t
CMP Voltage Reference source.
-
typedef struct _cmp_config cmp_config_t
Configures the comparator.
-
typedef struct _cmp_filter_config cmp_filter_config_t
Configures the filter.
-
typedef struct _cmp_dac_config cmp_dac_config_t
Configures the internal DAC.
-
struct _cmp_config
- #include <fsl_cmp.h>
Configures the comparator.
Public Members
-
bool enableCmp
Enable the CMP module.
-
cmp_hysteresis_mode_t hysteresisMode
CMP Hysteresis mode.
-
bool enableHighSpeed
Enable High-speed (HS) comparison mode.
-
bool enableInvertOutput
Enable the inverted comparator output.
-
bool useUnfilteredOutput
Set the compare output(COUT) to equal COUTA(true) or COUT(false).
-
bool enablePinOut
The comparator output is available on the associated pin.
-
bool enableTriggerMode
Enable the trigger mode.
-
bool enableCmp
-
struct _cmp_filter_config
- #include <fsl_cmp.h>
Configures the filter.
Public Members
-
bool enableSample
Using the external SAMPLE as a sampling clock input or using a divided bus clock.
-
uint8_t filterCount
Filter Sample Count. Available range is 1-7; 0 disables the filter.
-
uint8_t filterPeriod
Filter Sample Period. The divider to the bus clock. Available range is 0-255.
-
bool enableSample
-
struct _cmp_dac_config
- #include <fsl_cmp.h>
Configures the internal DAC.
Public Members
-
cmp_reference_voltage_source_t referenceVoltageSource
Supply voltage reference source.
-
uint8_t DACValue
Value for the DAC Output Voltage. Available range is 0-63.
-
cmp_reference_voltage_source_t referenceVoltageSource
CSI: CMOS Sensor Interface
-
status_t CSI_Init(CSI_Type *base, const csi_config_t *config)
Initialize the CSI.
This function enables the CSI peripheral clock, and resets the CSI registers.
- Parameters:
base – CSI peripheral base address.
config – Pointer to the configuration structure.
- Return values:
kStatus_Success – Initialize successfully.
kStatus_InvalidArgument – Initialize failed because of invalid argument.
-
void CSI_Deinit(CSI_Type *base)
De-initialize the CSI.
This function disables the CSI peripheral clock.
- Parameters:
base – CSI peripheral base address.
-
void CSI_Reset(CSI_Type *base)
Reset the CSI.
This function resets the CSI peripheral registers to default status.
- Parameters:
base – CSI peripheral base address.
-
void CSI_GetDefaultConfig(csi_config_t *config)
Get the default configuration for to initialize the CSI.
The default configuration value is:
config->width = 320U; config->height = 240U; config->polarityFlags = kCSI_HsyncActiveHigh | kCSI_DataLatchOnRisingEdge; config->bytesPerPixel = 2U; config->linePitch_Bytes = 320U * 2U; config->workMode = kCSI_GatedClockMode; config->dataBus = kCSI_DataBus8Bit; config->useExtVsync = true;
- Parameters:
config – Pointer to the CSI configuration.
-
void CSI_ClearFifo(CSI_Type *base, csi_fifo_t fifo)
Clear the CSI FIFO.
This function clears the CSI FIFO.
- Parameters:
base – CSI peripheral base address.
fifo – The FIFO to clear.
-
void CSI_ReflashFifoDma(CSI_Type *base, csi_fifo_t fifo)
Reflash the CSI FIFO DMA.
This function reflashes the CSI FIFO DMA.
For RXFIFO, there are two frame buffers. When the CSI module started, it saves the frames to frame buffer 0 then frame buffer 1, the two buffers will be written by turns. After reflash DMA using this function, the CSI is reset to save frame to buffer 0.
- Parameters:
base – CSI peripheral base address.
fifo – The FIFO DMA to reflash.
-
void CSI_EnableFifoDmaRequest(CSI_Type *base, csi_fifo_t fifo, bool enable)
Enable or disable the CSI FIFO DMA request.
- Parameters:
base – CSI peripheral base address.
fifo – The FIFO DMA reques to enable or disable.
enable – True to enable, false to disable.
-
static inline void CSI_Start(CSI_Type *base)
Start to receive data.
- Parameters:
base – CSI peripheral base address.
-
static inline void CSI_Stop(CSI_Type *base)
Stop to receiving data.
- Parameters:
base – CSI peripheral base address.
-
void CSI_SetRxBufferAddr(CSI_Type *base, uint8_t index, uint32_t addr)
Set the RX frame buffer address.
- Parameters:
base – CSI peripheral base address.
index – Buffer index.
addr – Frame buffer address to set.
-
void CSI_EnableInterrupts(CSI_Type *base, uint32_t mask)
Enables CSI interrupt requests.
- Parameters:
base – CSI peripheral base address.
mask – The interrupts to enable, pass in as OR’ed value of _csi_interrupt_enable.
-
void CSI_DisableInterrupts(CSI_Type *base, uint32_t mask)
Disable CSI interrupt requests.
- Parameters:
base – CSI peripheral base address.
mask – The interrupts to disable, pass in as OR’ed value of _csi_interrupt_enable.
-
static inline uint32_t CSI_GetStatusFlags(CSI_Type *base)
Gets the CSI status flags.
- Parameters:
base – CSI peripheral base address.
- Returns:
status flag, it is OR’ed value of _csi_flags.
-
static inline void CSI_ClearStatusFlags(CSI_Type *base, uint32_t statusMask)
Clears the CSI status flag.
The flags to clear are passed in as OR’ed value of _csi_flags. The following flags are cleared automatically by hardware:
kCSI_RxFifoFullFlag,
kCSI_StatFifoFullFlag,
kCSI_Field0PresentFlag,
kCSI_Field1PresentFlag,
kCSI_RxFifoDataReadyFlag,
- Parameters:
base – CSI peripheral base address.
statusMask – The status flags mask, OR’ed value of _csi_flags.
-
status_t CSI_TransferCreateHandle(CSI_Type *base, csi_handle_t *handle, csi_transfer_callback_t callback, void *userData)
Initializes the CSI handle.
This function initializes CSI handle, it should be called before any other CSI transactional functions.
- Parameters:
base – CSI peripheral base address.
handle – Pointer to the handle structure.
callback – Callback function for CSI transfer.
userData – Callback function parameter.
- Return values:
kStatus_Success – Handle created successfully.
-
status_t CSI_TransferStart(CSI_Type *base, csi_handle_t *handle)
Start the transfer using transactional functions.
When the empty frame buffers have been submit to CSI driver using function CSI_TransferSubmitEmptyBuffer, user could call this function to start the transfer. The incoming frame will be saved to the empty frame buffer, and user could be optionally notified through callback function.
- Parameters:
base – CSI peripheral base address.
handle – Pointer to the handle structure.
- Return values:
kStatus_Success – Started successfully.
kStatus_CSI_NoEmptyBuffer – Could not start because no empty frame buffer in queue.
-
status_t CSI_TransferStop(CSI_Type *base, csi_handle_t *handle)
Stop the transfer using transactional functions.
The driver does not clean the full frame buffers in queue. In other words, after calling this function, user still could get the full frame buffers in queue using function CSI_TransferGetFullBuffer.
- Parameters:
base – CSI peripheral base address.
handle – Pointer to the handle structure.
- Return values:
kStatus_Success – Stoped successfully.
-
status_t CSI_TransferSubmitEmptyBuffer(CSI_Type *base, csi_handle_t *handle, uint32_t frameBuffer)
Submit empty frame buffer to queue.
This function could be called before CSI_TransferStart or after CSI_TransferStart. If there is no room in queue to store the empty frame buffer, this function returns error.
- Parameters:
base – CSI peripheral base address.
handle – Pointer to the handle structure.
frameBuffer – Empty frame buffer to submit.
- Return values:
kStatus_Success – Started successfully.
kStatus_CSI_QueueFull – Could not submit because there is no room in queue.
-
status_t CSI_TransferGetFullBuffer(CSI_Type *base, csi_handle_t *handle, uint32_t *frameBuffer)
Get one full frame buffer from queue.
After the transfer started using function CSI_TransferStart, the incoming frames will be saved to the empty frame buffers in queue. This function gets the full-filled frame buffer from the queue. If there is no full frame buffer in queue, this function returns error.
- Parameters:
base – CSI peripheral base address.
handle – Pointer to the handle structure.
frameBuffer – Full frame buffer.
- Return values:
kStatus_Success – Started successfully.
kStatus_CSI_NoFullBuffer – There is no full frame buffer in queue.
-
void CSI_TransferHandleIRQ(CSI_Type *base, csi_handle_t *handle)
CSI IRQ handle function.
This function handles the CSI IRQ request to work with CSI driver transactional APIs.
- Parameters:
base – CSI peripheral base address.
handle – CSI handle pointer.
-
FSL_CSI_DRIVER_VERSION
Error codes for the CSI driver.
Values:
-
enumerator kStatus_CSI_NoEmptyBuffer
No empty frame buffer in queue to load to CSI.
-
enumerator kStatus_CSI_NoFullBuffer
No full frame buffer in queue to read out.
-
enumerator kStatus_CSI_QueueFull
Queue is full, no room to save new empty buffer.
-
enumerator kStatus_CSI_FrameDone
New frame received and saved to queue.
-
enumerator kStatus_CSI_NoEmptyBuffer
-
enum _csi_work_mode
CSI work mode.
The CCIR656 interlace mode is not supported currently.
Values:
-
enumerator kCSI_GatedClockMode
HSYNC, VSYNC, and PIXCLK signals are used.
-
enumerator kCSI_NonGatedClockMode
VSYNC, and PIXCLK signals are used.
-
enumerator kCSI_CCIR656ProgressiveMode
CCIR656 progressive mode.
-
enumerator kCSI_GatedClockMode
-
enum _csi_data_bus
CSI data bus witdh.
Values:
-
enumerator kCSI_DataBus8Bit
8-bit data bus.
-
enumerator kCSI_DataBus16Bit
16-bit data bus.
-
enumerator kCSI_DataBus24Bit
24-bit data bus.
-
enumerator kCSI_DataBus8Bit
-
enum _csi_polarity_flags
CSI signal polarity.
Values:
-
enumerator kCSI_HsyncActiveLow
HSYNC is active low.
-
enumerator kCSI_HsyncActiveHigh
HSYNC is active high.
-
enumerator kCSI_DataLatchOnRisingEdge
Pixel data latched at rising edge of pixel clock.
-
enumerator kCSI_DataLatchOnFallingEdge
Pixel data latched at falling edge of pixel clock.
-
enumerator kCSI_VsyncActiveHigh
VSYNC is active high.
-
enumerator kCSI_VsyncActiveLow
VSYNC is active low.
-
enumerator kCSI_HsyncActiveLow
-
enum _csi_fifo
The CSI FIFO, used for FIFO operation.
Values:
-
enumerator kCSI_RxFifo
RXFIFO.
-
enumerator kCSI_StatFifo
STAT FIFO.
-
enumerator kCSI_AllFifo
Both RXFIFO and STAT FIFO.
-
enumerator kCSI_RxFifo
-
enum _csi_interrupt_enable
CSI feature interrupt source.
Values:
-
enumerator kCSI_EndOfFrameInterruptEnable
End of frame interrupt enable.
-
enumerator kCSI_ChangeOfFieldInterruptEnable
Change of field interrupt enable.
-
enumerator kCSI_StatFifoOverrunInterruptEnable
STAT FIFO overrun interrupt enable.
-
enumerator kCSI_RxFifoOverrunInterruptEnable
RXFIFO overrun interrupt enable.
-
enumerator kCSI_StatFifoDmaDoneInterruptEnable
STAT FIFO DMA done interrupt enable.
-
enumerator kCSI_StatFifoFullInterruptEnable
STAT FIFO full interrupt enable.
-
enumerator kCSI_RxBuffer1DmaDoneInterruptEnable
RX frame buffer 1 DMA transfer done.
-
enumerator kCSI_RxBuffer0DmaDoneInterruptEnable
RX frame buffer 0 DMA transfer done.
-
enumerator kCSI_RxFifoFullInterruptEnable
RXFIFO full interrupt enable.
-
enumerator kCSI_StartOfFrameInterruptEnable
Start of frame (SOF) interrupt enable.
-
enumerator kCSI_EccErrorInterruptEnable
ECC error detection interrupt enable.
-
enumerator kCSI_AhbResErrorInterruptEnable
AHB response Error interrupt enable.
-
enumerator kCSI_BaseAddrChangeErrorInterruptEnable
The DMA output buffer base address changes before DMA completed.
-
enumerator kCSI_Field0DoneInterruptEnable
Field 0 done interrupt enable.
-
enumerator kCSI_Field1DoneInterruptEnable
Field 1 done interrupt enable.
-
enumerator kCSI_EndOfFrameInterruptEnable
-
enum _csi_flags
CSI status flags.
The following status register flags can be cleared:
kCSI_EccErrorFlag
kCSI_AhbResErrorFlag
kCSI_ChangeOfFieldFlag
kCSI_StartOfFrameFlag
kCSI_EndOfFrameFlag
kCSI_RxBuffer1DmaDoneFlag
kCSI_RxBuffer0DmaDoneFlag
kCSI_StatFifoDmaDoneFlag
kCSI_StatFifoOverrunFlag
kCSI_RxFifoOverrunFlag
kCSI_Field0DoneFlag
kCSI_Field1DoneFlag
kCSI_BaseAddrChangeErrorFlag
Values:
-
enumerator kCSI_RxFifoDataReadyFlag
RXFIFO data ready.
-
enumerator kCSI_EccErrorFlag
ECC error detected.
-
enumerator kCSI_AhbResErrorFlag
Hresponse (AHB bus response) Error.
-
enumerator kCSI_ChangeOfFieldFlag
Change of field.
-
enumerator kCSI_Field0PresentFlag
Field 0 present in CCIR mode.
-
enumerator kCSI_Field1PresentFlag
Field 1 present in CCIR mode.
-
enumerator kCSI_StartOfFrameFlag
Start of frame (SOF) detected.
-
enumerator kCSI_EndOfFrameFlag
End of frame (EOF) detected.
-
enumerator kCSI_RxFifoFullFlag
RXFIFO full (Number of data reaches trigger level).
-
enumerator kCSI_RxBuffer1DmaDoneFlag
RX frame buffer 1 DMA transfer done.
-
enumerator kCSI_RxBuffer0DmaDoneFlag
RX frame buffer 0 DMA transfer done.
-
enumerator kCSI_StatFifoFullFlag
STAT FIFO full (Reach trigger level).
-
enumerator kCSI_StatFifoDmaDoneFlag
STAT FIFO DMA transfer done.
-
enumerator kCSI_StatFifoOverrunFlag
STAT FIFO overrun.
-
enumerator kCSI_RxFifoOverrunFlag
RXFIFO overrun.
-
enumerator kCSI_Field0DoneFlag
Field 0 transfer done.
-
enumerator kCSI_Field1DoneFlag
Field 1 transfer done.
-
enumerator kCSI_BaseAddrChangeErrorFlag
The DMA output buffer base address changes before DMA completed.
-
typedef enum _csi_work_mode csi_work_mode_t
CSI work mode.
The CCIR656 interlace mode is not supported currently.
-
typedef enum _csi_data_bus csi_data_bus_t
CSI data bus witdh.
-
typedef struct _csi_config csi_config_t
Configuration to initialize the CSI module.
-
typedef enum _csi_fifo csi_fifo_t
The CSI FIFO, used for FIFO operation.
-
typedef struct _csi_handle csi_handle_t
-
typedef void (*csi_transfer_callback_t)(CSI_Type *base, csi_handle_t *handle, status_t status, void *userData)
CSI transfer callback function.
When a new frame is received and saved to the frame buffer queue, the callback is called and the pass the status kStatus_CSI_FrameDone to upper layer.
-
CSI_REG_CR1(base)
-
CSI_REG_CR2(base)
-
CSI_REG_CR3(base)
-
CSI_REG_CR18(base)
-
CSI_REG_SR(base)
-
CSI_REG_DMASA_FB1(base)
-
CSI_REG_DMASA_FB2(base)
-
CSI_REG_IMAG_PARA(base)
-
CSI_REG_FBUF_PARA(base)
-
CSI_DRIVER_QUEUE_SIZE
Size of the frame buffer queue used in CSI transactional function.
-
CSI_DRIVER_FRAG_MODE
Enable fragment capture function or not.
-
CSI_CR1_INT_EN_MASK
-
CSI_CR3_INT_EN_MASK
-
CSI_CR18_INT_EN_MASK
-
struct _csi_config
- #include <fsl_csi.h>
Configuration to initialize the CSI module.
Public Members
-
uint16_t width
Pixels of the input frame.
-
uint16_t height
Lines of the input frame.
-
uint32_t polarityFlags
Timing signal polarity flags, OR’ed value of _csi_polarity_flags.
-
uint8_t bytesPerPixel
Bytes per pixel, valid values are:
2: Used for RGB565, YUV422, and so on.
4: Used for XRGB8888, XYUV444, and so on.
-
uint16_t linePitch_Bytes
Frame buffer line pitch, must be 8-byte aligned.
-
csi_work_mode_t workMode
CSI work mode.
-
csi_data_bus_t dataBus
Data bus width.
-
bool useExtVsync
In CCIR656 progressive mode, set true to use external VSYNC signal, set false to use internal VSYNC signal decoded from SOF.
-
uint16_t width
-
struct buf_queue_t
- #include <fsl_csi.h>
-
struct _csi_handle
- #include <fsl_csi.h>
CSI handle structure.
Please see the user guide for the details of the CSI driver queue mechanism.
Public Members
-
volatile uint8_t activeBufferNum
How many frame buffers are in progress currently.
-
volatile uint8_t dmaDoneBufferIdx
Index of the current full-filled framebuffer.
-
volatile bool transferStarted
User has called CSI_TransferStart to start frame receiving.
-
csi_transfer_callback_t callback
Callback function.
-
void *userData
CSI callback function parameter.
-
volatile uint8_t activeBufferNum
DCDC: DCDC Converter
-
void DCDC_Init(DCDC_Type *base, dcdc_config_t *config)
Enable the access to DCDC registers.
- Parameters:
base – DCDC peripheral base address.
config – Pointer to the configuration structure.
-
void DCDC_Deinit(DCDC_Type *base)
Disable the access to DCDC registers.
- Parameters:
base – DCDC peripheral base address.
-
void DCDC_GetDefaultConfig(DCDC_Type *base, dcdc_config_t *config)
brief Get the default setting for DCDC user configuration structure.
This function initializes the user configuration structure to a default value. The default values are: code config->controlMode = kDCDC_StaticControl; config->trimInputMode = kDCDC_SampleTrimInput; config->enableDcdcTimeout = false; config->enableSwitchingConverterOutput = false; endcode
param config Pointer to configuration structure. See to “dcdc_config_t”
-
uint32_t DCDC_GetstatusFlags(DCDC_Type *base)
Get DCDC status flags.
- Parameters:
base – peripheral base address.
- Returns:
Mask of asserted status flags. See to “_dcdc_status_flags_t”.
-
void DCDC_EnterLowPowerMode(DCDC_Type *base, dcdc_low_power_mode_t mode)
Make DCDC enter into low power modes.
- Parameters:
base – DCDC peripheral base address.
mode – DCDC low power mode selection. See to “_dcdc_low_power_mode”
-
static inline void DCDC_EnableOutputRangeComparator(DCDC_Type *base, bool enable)
Enable the output range comparator.
The output range comparator is disabled by default.
- Parameters:
base – DCDC peripheral base address.
enable – Enable the feature or not.
-
void DCDC_SetClockSource(DCDC_Type *base, dcdc_clock_source_t clockSource)
Configure the DCDC clock source.
- Parameters:
base – DCDC peripheral base address.
clockSource – Clock source for DCDC. See to “dcdc_clock_source_t”.
-
void DCDC_GetDefaultDetectionConfig(dcdc_detection_config_t *config)
Get the default setting for detection configuration.
The default configuration are set according to responding registers’ setting when powered on. They are:
config->enableXtalokDetection = false; config->powerDownOverVoltageDetection = true; config->powerDownLowVlotageDetection = false; config->powerDownOverCurrentDetection = true; config->powerDownPeakCurrentDetection = true; config->powerDownZeroCrossDetection = true; config->OverCurrentThreshold = kDCDC_OverCurrentThresholdAlt0; config->PeakCurrentThreshold = kDCDC_PeakCurrentThresholdAlt0;
- Parameters:
config – Pointer to configuration structure. See to “dcdc_detection_config_t”
-
void DCDC_SetDetectionConfig(DCDC_Type *base, const dcdc_detection_config_t *config)
Configure the DCDC detection.
- Parameters:
base – DCDC peripheral base address.
config – Pointer to configuration structure. See to “dcdc_detection_config_t”
-
void DCDC_GetDefaultLowPowerConfig(dcdc_low_power_config_t *config)
Get the default setting for low power configuration.
The default configuration are set according to responding registers’ setting when powered on. They are:
config->enableOverloadDetection = true; config->enableAdjustHystereticValue = false; config->countChargingTimePeriod = kDCDC_CountChargingTimePeriod8Cycle; config->countChargingTimeThreshold = kDCDC_CountChargingTimeThreshold32;
- Parameters:
config – Pointer to configuration structure. See to “dcdc_low_power_config_t”
-
void DCDC_SetLowPowerConfig(DCDC_Type *base, const dcdc_low_power_config_t *config)
Configure the DCDC low power.
- Parameters:
base – DCDC peripheral base address.
config – Pointer to configuration structure. See to “dcdc_low_power_config_t”.
-
void DCDC_ResetCurrentAlertSignal(DCDC_Type *base, bool enable)
Reset current alert signal. Alert signal is generate by peak current detection.
- Parameters:
base – DCDC peripheral base address.
enable – Switcher to reset signal. True means reset signal. False means don’t reset signal.
-
static inline void DCDC_SetBandgapVoltageTrimValue(DCDC_Type *base, uint32_t trimValue)
Set the bangap trim value to trim bandgap voltage.
- Parameters:
base – DCDC peripheral base address.
trimValue – The bangap trim value. Available range is 0U-31U.
-
void DCDC_GetDefaultLoopControlConfig(dcdc_loop_control_config_t *config)
Get the default setting for loop control configuration.
The default configuration are set according to responding registers’ setting when powered on. They are:
config->enableCommonHysteresis = false; config->enableCommonThresholdDetection = false; config->enableInvertHysteresisSign = false; config->enableRCThresholdDetection = false; config->enableRCScaleCircuit = 0U; config->complementFeedForwardStep = 0U;
- Parameters:
config – Pointer to configuration structure. See to “dcdc_loop_control_config_t”
-
void DCDC_SetLoopControlConfig(DCDC_Type *base, const dcdc_loop_control_config_t *config)
Configure the DCDC loop control.
- Parameters:
base – DCDC peripheral base address.
config – Pointer to configuration structure. See to “dcdc_loop_control_config_t”.
-
void DCDC_SetMinPowerConfig(DCDC_Type *base, const dcdc_min_power_config_t *config)
Configure for the min power.
- Parameters:
base – DCDC peripheral base address.
config – Pointer to configuration structure. See to “dcdc_min_power_config_t”.
-
static inline void DCDC_SetLPComparatorBiasValue(DCDC_Type *base, dcdc_comparator_current_bias_t biasVaule)
Set the current bias of low power comparator.
- Parameters:
base – DCDC peripheral base address.
biasVaule – The current bias of low power comparator. Refer to “dcdc_comparator_current_bias_t”.
-
static inline void DCDC_LockTargetVoltage(DCDC_Type *base)
Lock target voltage.
- Parameters:
base – DCDC peripheral base address.
-
void DCDC_AdjustTargetVoltage(DCDC_Type *base, uint32_t VDDRun, uint32_t VDDStandby)
Adjust the target voltage of VDD_SOC in run mode and low power mode.
- Deprecated:
Do not use this function. It has been superceded by DCDC_AdjustRunTargetVoltage and DCDC_AdjustLowPowerTargetVoltage
This function is to adjust the target voltage of DCDC output. Change them and finally wait until the output is stabled. Set the target value of run mode the same as low power mode before entering power save mode, because DCDC will switch back to run mode if it detects the current loading is larger than about 50 mA(typical value).
- Parameters:
base – DCDC peripheral base address.
VDDRun – Target value in run mode. 25 mV each step from 0x00 to 0x1F. 00 is for 0.8V, 0x1F is for 1.575V.
VDDStandby – Target value in low power mode. 25 mV each step from 0x00 to 0x4. 00 is for 0.9V, 0x4 is for 1.0V.
-
void DCDC_AdjustRunTargetVoltage(DCDC_Type *base, uint32_t VDDRun)
Adjust the target voltage of VDD_SOC in run mode.
This function is to adjust the target voltage of DCDC output. Change them and finally wait until the output is stabled. Set the target value of run mode the same as low power mode before entering power save mode, because DCDC will switch back to run mode if it detects the current loading is larger than about 50 mA(typical value).
- Parameters:
base – DCDC peripheral base address.
VDDRun – Target value in run mode. 25 mV each step from 0x00 to 0x1F. 00 is for 0.8V, 0x1F is for 1.575V.
-
void DCDC_AdjustLowPowerTargetVoltage(DCDC_Type *base, uint32_t VDDStandby)
Adjust the target voltage of VDD_SOC in low power mode.
This function is to adjust the target voltage of DCDC output. Change them and finally wait until the output is stabled. Set the target value of run mode the same as low power mode before entering power save mode, because DCDC will switch back to run mode if it detects the current loading is larger than about 50 mA(typical value).
- Parameters:
base – DCDC peripheral base address.
VDDStandby – Target value in low power mode. 25 mV each step from 0x00 to 0x4. 00 is for 0.9V, 0x4 is for 1.0V.
-
void DCDC_SetInternalRegulatorConfig(DCDC_Type *base, const dcdc_internal_regulator_config_t *config)
Configure the DCDC internal regulator.
- Parameters:
base – DCDC peripheral base address.
config – Pointer to configuration structure. See to “dcdc_internal_regulator_config_t”.
-
static inline void DCDC_EnableImproveTransition(DCDC_Type *base, bool enable)
Enable/Disable to improve the transition from heavy load to light load. It is valid while zero cross detection is enabled. If ouput exceeds the threshold, DCDC would return CCM from DCM.
- Parameters:
base – DCDC peripheral base address.
enable – Enable the feature or not.
-
void DCDC_BootIntoDCM(DCDC_Type *base)
Boot DCDC into DCM(discontinous conduction mode).
pwd_zcd=0x0; pwd_cmp_offset=0x0; dcdc_loopctrl_en_rcscale= 0x5; DCM_set_ctrl=1’b1;
- Parameters:
base – DCDC peripheral base address.
-
void DCDC_BootIntoCCM(DCDC_Type *base)
Boot DCDC into CCM(continous conduction mode).
pwd_zcd=0x1; pwd_cmp_offset=0x0; dcdc_loopctrl_en_rcscale=0x3;
- Parameters:
base – DCDC peripheral base address.
-
enum _dcdc_status_flags_t
DCDC status flags.
Values:
-
enumerator kDCDC_LockedOKStatus
Indicate DCDC status. 1’b1: DCDC already settled 1’b0: DCDC is settling.
-
enumerator kDCDC_LockedOKStatus
-
enum _dcdc_comparator_current_bias
The current bias of low power comparator.
Values:
-
enumerator kDCDC_ComparatorCurrentBias50nA
The current bias of low power comparator is 50nA.
-
enumerator kDCDC_ComparatorCurrentBias100nA
The current bias of low power comparator is 100nA.
-
enumerator kDCDC_ComparatorCurrentBias200nA
The current bias of low power comparator is 200nA.
-
enumerator kDCDC_ComparatorCurrentBias400nA
The current bias of low power comparator is 400nA.
-
enumerator kDCDC_ComparatorCurrentBias50nA
-
enum _dcdc_over_current_threshold
The threshold of over current detection.
Values:
-
enumerator kDCDC_OverCurrentThresholdAlt0
1A in the run mode, 0.25A in the power save mode.
-
enumerator kDCDC_OverCurrentThresholdAlt1
2A in the run mode, 0.25A in the power save mode.
-
enumerator kDCDC_OverCurrentThresholdAlt2
1A in the run mode, 0.2A in the power save mode.
-
enumerator kDCDC_OverCurrentThresholdAlt3
2A in the run mode, 0.2A in the power save mode.
-
enumerator kDCDC_OverCurrentThresholdAlt0
-
enum _dcdc_peak_current_threshold
The threshold if peak current detection.
Values:
-
enumerator kDCDC_PeakCurrentThresholdAlt0
150mA peak current threshold.
-
enumerator kDCDC_PeakCurrentThresholdAlt1
250mA peak current threshold.
-
enumerator kDCDC_PeakCurrentThresholdAlt2
350mA peak current threshold.
-
enumerator kDCDC_PeakCurrentThresholdAlt3
450mA peak current threshold.
-
enumerator kDCDC_PeakCurrentThresholdAlt4
550mA peak current threshold.
-
enumerator kDCDC_PeakCurrentThresholdAlt5
650mA peak current threshold.
-
enumerator kDCDC_PeakCurrentThresholdAlt0
-
enum _dcdc_count_charging_time_period
The period of counting the charging times in power save mode.
Values:
-
enumerator kDCDC_CountChargingTimePeriod8Cycle
Eight 32k cycle.
-
enumerator kDCDC_CountChargingTimePeriod16Cycle
Sixteen 32k cycle.
-
enumerator kDCDC_CountChargingTimePeriod8Cycle
-
enum _dcdc_count_charging_time_threshold
The threshold of the counting number of charging times.
Values:
-
enumerator kDCDC_CountChargingTimeThreshold32
0x0: 32.
-
enumerator kDCDC_CountChargingTimeThreshold64
0x1: 64.
-
enumerator kDCDC_CountChargingTimeThreshold16
0x2: 16.
-
enumerator kDCDC_CountChargingTimeThreshold8
0x3: 8.
-
enumerator kDCDC_CountChargingTimeThreshold32
-
enum _dcdc_clock_source
Oscillator clock option.
Values:
-
enumerator kDCDC_ClockAutoSwitch
Automatic clock switch from internal oscillator to external clock.
-
enumerator kDCDC_ClockInternalOsc
Use internal oscillator.
-
enumerator kDCDC_ClockExternalOsc
Use external 24M crystal oscillator.
-
enumerator kDCDC_ClockAutoSwitch
-
enum _dcdc_low_power_mode
DCDC low power modes.
Values:
-
enumerator kDCDC_StandbyMode
Standby mode.
-
enumerator kDCDC_LowPowerMode
Low power mode.
-
enumerator kDCDC_GpcStandbyLowPowerMode
low power mode for GPC standby request.
-
enumerator kDCDC_StandbyMode
-
enum _dcdc_control_mode
DCDC control mode.
Values:
-
enumerator kDCDC_StaticControl
Static control.
-
enumerator kDCDC_SetPointControl
Controlled by GPC set points.
-
enumerator kDCDC_StaticControl
-
enum _dcdc_trim_input_mode
DCDC trim input mode.
Values:
-
enumerator kDCDC_SampleTrimInput
Sample trim input.
-
enumerator kDCDC_HoldTrimInput
Hold trim input.
-
enumerator kDCDC_SampleTrimInput
-
typedef enum _dcdc_comparator_current_bias dcdc_comparator_current_bias_t
The current bias of low power comparator.
-
typedef enum _dcdc_over_current_threshold dcdc_over_current_threshold_t
The threshold of over current detection.
-
typedef enum _dcdc_peak_current_threshold dcdc_peak_current_threshold_t
The threshold if peak current detection.
-
typedef enum _dcdc_count_charging_time_period dcdc_count_charging_time_period_t
The period of counting the charging times in power save mode.
-
typedef enum _dcdc_count_charging_time_threshold dcdc_count_charging_time_threshold_t
The threshold of the counting number of charging times.
-
typedef enum _dcdc_clock_source dcdc_clock_source_t
Oscillator clock option.
-
typedef enum _dcdc_low_power_mode dcdc_low_power_mode_t
DCDC low power modes.
-
typedef enum _dcdc_control_mode dcdc_control_mode_t
DCDC control mode.
-
typedef enum _dcdc_trim_input_mode dcdc_trim_input_mode_t
DCDC trim input mode.
-
typedef struct _dcdc_config dcdc_config_t
Configuration for DCDC.
-
typedef struct _dcdc_detection_config dcdc_detection_config_t
Configuration for DCDC detection.
-
typedef struct _dcdc_loop_control_config dcdc_loop_control_config_t
Configuration for the loop control.
-
typedef struct _dcdc_low_power_config dcdc_low_power_config_t
Configuration for DCDC low power.
-
typedef struct _dcdc_internal_regulator_config dcdc_internal_regulator_config_t
Configuration for DCDC internal regulator.
-
typedef struct _dcdc_min_power_config dcdc_min_power_config_t
Configuration for min power setting.
-
FSL_DCDC_DRIVER_VERSION
DCDC driver version.
Version 2.3.0.
-
struct _dcdc_config
- #include <fsl_dcdc.h>
Configuration for DCDC.
Public Members
-
dcdc_control_mode_t controlMode
DCDC control mode.
-
dcdc_trim_input_mode_t trimInputMode
Hold trim input.
-
bool enableDcdcTimeout
Enable internal count for DCDC_OK timeout.
-
bool enableSwitchingConverterOutput
Enable the VDDIO switching converter output.
-
dcdc_control_mode_t controlMode
-
struct _dcdc_detection_config
- #include <fsl_dcdc.h>
Configuration for DCDC detection.
Public Members
-
bool enableXtalokDetection
Enable xtalok detection circuit.
-
bool powerDownOverVoltageDetection
Power down over-voltage detection comparator.
-
bool powerDownLowVlotageDetection
Power down low-voltage detection comparator.
-
bool powerDownOverCurrentDetection
Power down over-current detection.
-
bool powerDownPeakCurrentDetection
Power down peak-current detection.
-
bool powerDownZeroCrossDetection
Power down the zero cross detection function for discontinuous conductor mode.
-
dcdc_over_current_threshold_t OverCurrentThreshold
The threshold of over current detection.
-
dcdc_peak_current_threshold_t PeakCurrentThreshold
The threshold of peak current detection.
-
bool enableXtalokDetection
-
struct _dcdc_loop_control_config
- #include <fsl_dcdc.h>
Configuration for the loop control.
Public Members
-
bool enableCommonHysteresis
Enable hysteresis in switching converter common mode analog comparators. This feature will improve transient supply ripple and efficiency.
-
bool enableCommonThresholdDetection
Increase the threshold detection for common mode analog comparator.
-
bool enableDifferentialHysteresis
Enable hysteresis in switching converter differential mode analog comparators. This feature will improve transient supply ripple and efficiency.
-
bool enableDifferentialThresholdDetection
Increase the threshold detection for differential mode analog comparators.
-
bool enableInvertHysteresisSign
Invert the sign of the hysteresis in DC-DC analog comparators.
-
bool enableRCThresholdDetection
Increase the threshold detection for RC scale circuit.
-
uint32_t enableRCScaleCircuit
Available range is 0~7. Enable analog circuit of DC-DC converter to respond faster under transient load conditions.
-
uint32_t complementFeedForwardStep
Available range is 0~7. Two’s complement feed forward step in duty cycle in the switching DC-DC converter. Each time this field makes a transition from 0x0, the loop filter of the DC-DC converter is stepped once by a value proportional to the change. This can be used to force a certain control loop behavior, such as improving response under known heavy load transients.
-
bool enableCommonHysteresis
-
struct _dcdc_low_power_config
- #include <fsl_dcdc.h>
Configuration for DCDC low power.
Public Members
-
bool enableAdjustHystereticValue
Adjust hysteretic value in low power from 12.5mV to 25mV.
-
dcdc_count_charging_time_period_t countChargingTimePeriod
The period of counting the charging times in power save mode.
-
dcdc_count_charging_time_threshold_t countChargingTimeThreshold
the threshold of the counting number of charging times during the period that lp_overload_freq_sel sets in power save mode.
-
bool enableAdjustHystereticValue
-
struct _dcdc_internal_regulator_config
- #include <fsl_dcdc.h>
Configuration for DCDC internal regulator.
Public Members
-
bool enableLoadResistor
control the load resistor of the internal regulator of DCDC, the load resistor is connected as default “true”, and need set to “false” to disconnect the load resistor.
-
uint32_t feedbackPoint
Available range is 0~3. Select the feedback point of the internal regulator.
-
bool enableLoadResistor
-
struct _dcdc_min_power_config
- #include <fsl_dcdc.h>
Configuration for min power setting.
Public Members
-
bool enableUseHalfFreqForContinuous
Set DCDC clock to half frequency for the continuous mode.
-
bool enableUseHalfFreqForContinuous
DCP: Data Co-Processor
-
FSL_DCP_DRIVER_VERSION
DCP driver version. Version 2.1.7.
Current version: 2.1.7
Change log:
Version 2.1.7
Bug Fix
Reduce optimization level for critical functions working with SRF.
Version 2.1.6
Bug Fix
MISRA C-2012 issue fix.
Version 2.1.5
Improvements
Add support for DCACHE.
Version 2.1.4
Bug Fix
Fix CRC-32 computation issue on the code’s block boundary size.
Version 2.1.3
Bug Fix
MISRA C-2012 issue fixed: rule 10.1, 10.3, 10.4, 11.9, 14.4, 16.4 and 17.7.
Version 2.1.2
Fix sign-compare warning in dcp_reverse_and_copy.
Version 2.1.1
Add DCP status clearing when channel operation is complete
2.1.0
Add byte/word swap feature for key, input and output data
Version 2.0.0
Initial version
-
enum _dcp_status
DCP status return codes.
Values:
-
enumerator kStatus_DCP_Again
Non-blocking function shall be called again.
-
enumerator kStatus_DCP_Again
-
enum _dcp_ch_enable
DCP channel enable.
Values:
-
enumerator kDCP_chDisable
DCP channel disable
-
enumerator kDCP_ch0Enable
DCP channel 0 enable
-
enumerator kDCP_ch1Enable
DCP channel 1 enable
-
enumerator kDCP_ch2Enable
DCP channel 2 enable
-
enumerator kDCP_ch3Enable
DCP channel 3 enable
-
enumerator kDCP_chEnableAll
DCP channel enable all
-
enumerator kDCP_chDisable
-
enum _dcp_ch_int_enable
DCP interrupt enable.
Values:
-
enumerator kDCP_chIntDisable
DCP interrupts disable
-
enumerator kDCP_ch0IntEnable
DCP channel 0 interrupt enable
-
enumerator kDCP_ch1IntEnable
DCP channel 1 interrupt enable
-
enumerator kDCP_ch2IntEnable
DCP channel 2 interrupt enable
-
enumerator kDCP_ch3IntEnable
DCP channel 3 interrupt enable
-
enumerator kDCP_chIntDisable
-
enum _dcp_channel
DCP channel selection.
Values:
-
enumerator kDCP_Channel0
DCP channel 0.
-
enumerator kDCP_Channel1
DCP channel 1.
-
enumerator kDCP_Channel2
DCP channel 2.
-
enumerator kDCP_Channel3
DCP channel 3.
-
enumerator kDCP_Channel0
-
enum _dcp_key_slot
DCP key slot selection.
Values:
-
enumerator kDCP_KeySlot0
DCP key slot 0.
-
enumerator kDCP_KeySlot1
DCP key slot 1.
-
enumerator kDCP_KeySlot2
DCP key slot 2.
-
enumerator kDCP_KeySlot3
DCP key slot 3.
-
enumerator kDCP_OtpKey
DCP OTP key.
-
enumerator kDCP_OtpUniqueKey
DCP unique OTP key.
-
enumerator kDCP_PayloadKey
DCP payload key.
-
enumerator kDCP_KeySlot0
-
enum _dcp_swap
DCP key, input & output swap options.
Values:
-
enumerator kDCP_NoSwap
-
enumerator kDCP_KeyByteSwap
-
enumerator kDCP_KeyWordSwap
-
enumerator kDCP_InputByteSwap
-
enumerator kDCP_InputWordSwap
-
enumerator kDCP_OutputByteSwap
-
enumerator kDCP_OutputWordSwap
-
enumerator kDCP_NoSwap
-
typedef enum _dcp_ch_enable _dcp_ch_enable_t
DCP channel enable.
-
typedef enum _dcp_ch_int_enable _dcp_ch_int_enable_t
DCP interrupt enable.
-
typedef enum _dcp_channel dcp_channel_t
DCP channel selection.
-
typedef enum _dcp_key_slot dcp_key_slot_t
DCP key slot selection.
-
typedef enum _dcp_swap dcp_swap_t
DCP key, input & output swap options.
-
typedef struct _dcp_work_packet dcp_work_packet_t
DCP’s work packet.
-
typedef struct _dcp_handle dcp_handle_t
Specify DCP’s key resource and DCP channel.
-
typedef struct _dcp_context dcp_context_t
DCP’s context buffer, used by DCP for context switching between channels.
-
typedef struct _dcp_config dcp_config_t
DCP’s configuration structure.
-
void DCP_Init(DCP_Type *base, const dcp_config_t *config)
Enables clock to and enables DCP.
Enable DCP clock and configure DCP.
- Parameters:
base – DCP base address
config – Pointer to configuration structure.
-
void DCP_Deinit(DCP_Type *base)
Disable DCP clock.
Reset DCP and Disable DCP clock.
- Parameters:
base – DCP base address
-
void DCP_GetDefaultConfig(dcp_config_t *config)
Gets the default configuration structure.
This function initializes the DCP configuration structure to a default value. The default values are as follows. dcpConfig->gatherResidualWrites = true; dcpConfig->enableContextCaching = true; dcpConfig->enableContextSwitching = true; dcpConfig->enableChannnel = kDCP_chEnableAll; dcpConfig->enableChannelInterrupt = kDCP_chIntDisable;
- Parameters:
config – [out] Pointer to configuration structure.
-
status_t DCP_WaitForChannelComplete(DCP_Type *base, dcp_handle_t *handle)
Poll and wait on DCP channel.
Polls the specified DCP channel until current it completes activity.
- Parameters:
base – DCP peripheral base address.
handle – Specifies DCP channel.
- Returns:
kStatus_Success When data processing completes without error.
- Returns:
kStatus_Fail When error occurs.
-
struct _dcp_work_packet
- #include <fsl_dcp.h>
DCP’s work packet.
-
struct _dcp_handle
- #include <fsl_dcp.h>
Specify DCP’s key resource and DCP channel.
Public Members
-
dcp_channel_t channel
Specify DCP channel.
-
dcp_key_slot_t keySlot
For operations with key (such as AES encryption/decryption), specify DCP key slot.
-
uint32_t swapConfig
For configuration of key, input, output byte/word swap options
-
dcp_channel_t channel
-
struct _dcp_context
- #include <fsl_dcp.h>
DCP’s context buffer, used by DCP for context switching between channels.
-
struct _dcp_config
- #include <fsl_dcp.h>
DCP’s configuration structure.
Public Members
-
bool gatherResidualWrites
Enable the ragged writes to the unaligned buffers.
-
bool enableContextCaching
Enable the caching of contexts between the operations.
-
bool enableContextSwitching
Enable automatic context switching for the channels.
-
uint8_t enableChannel
DCP channel enable.
-
uint8_t enableChannelInterrupt
Per-channel interrupt enable.
-
bool gatherResidualWrites
DCP AES blocking driver
-
status_t DCP_AES_SetKey(DCP_Type *base, dcp_handle_t *handle, const uint8_t *key, size_t keySize)
Set AES key to dcp_handle_t struct and optionally to DCP.
Sets the AES key for encryption/decryption with the dcp_handle_t structure. The dcp_handle_t input argument specifies keySlot. If the keySlot is kDCP_OtpKey, the function will check the OTP_KEY_READY bit and will return it’s ready to use status. For other keySlot selections, the function will copy and hold the key in dcp_handle_t struct. If the keySlot is one of the four DCP SRAM-based keys (one of kDCP_KeySlot0, kDCP_KeySlot1, kDCP_KeySlot2, kDCP_KeySlot3), this function will also load the supplied key to the specified keySlot in DCP.
- Parameters:
base – DCP peripheral base address.
handle – Handle used for the request.
key – 0-mod-4 aligned pointer to AES key.
keySize – AES key size in bytes. Shall equal 16.
- Returns:
status from set key operation
-
status_t DCP_AES_EncryptEcb(DCP_Type *base, dcp_handle_t *handle, const uint8_t *plaintext, uint8_t *ciphertext, size_t size)
Encrypts AES on one or multiple 128-bit block(s).
Encrypts AES. The source plaintext and destination ciphertext can overlap in system memory.
- Parameters:
base – DCP peripheral base address
handle – Handle used for this request.
plaintext – Input plain text to encrypt
ciphertext – [out] Output cipher text
size – Size of input and output data in bytes. Must be multiple of 16 bytes.
- Returns:
Status from encrypt operation
-
status_t DCP_AES_DecryptEcb(DCP_Type *base, dcp_handle_t *handle, const uint8_t *ciphertext, uint8_t *plaintext, size_t size)
Decrypts AES on one or multiple 128-bit block(s).
Decrypts AES. The source ciphertext and destination plaintext can overlap in system memory.
- Parameters:
base – DCP peripheral base address
handle – Handle used for this request.
ciphertext – Input plain text to encrypt
plaintext – [out] Output cipher text
size – Size of input and output data in bytes. Must be multiple of 16 bytes.
- Returns:
Status from decrypt operation
-
status_t DCP_AES_EncryptCbc(DCP_Type *base, dcp_handle_t *handle, const uint8_t *plaintext, uint8_t *ciphertext, size_t size, const uint8_t iv[16])
Encrypts AES using CBC block mode.
Encrypts AES using CBC block mode. The source plaintext and destination ciphertext can overlap in system memory.
- Parameters:
base – DCP peripheral base address
handle – Handle used for this request.
plaintext – Input plain text to encrypt
ciphertext – [out] Output cipher text
size – Size of input and output data in bytes. Must be multiple of 16 bytes.
iv – Input initial vector to combine with the first input block.
- Returns:
Status from encrypt operation
-
status_t DCP_AES_DecryptCbc(DCP_Type *base, dcp_handle_t *handle, const uint8_t *ciphertext, uint8_t *plaintext, size_t size, const uint8_t iv[16])
Decrypts AES using CBC block mode.
Decrypts AES using CBC block mode. The source ciphertext and destination plaintext can overlap in system memory.
- Parameters:
base – DCP peripheral base address
handle – Handle used for this request.
ciphertext – Input cipher text to decrypt
plaintext – [out] Output plain text
size – Size of input and output data in bytes. Must be multiple of 16 bytes.
iv – Input initial vector to combine with the first input block.
- Returns:
Status from decrypt operation
-
DCP_AES_BLOCK_SIZE
AES block size in bytes
DCP HASH driver
-
enum _dcp_hash_algo_t
Supported cryptographic block cipher functions for HASH creation.
Values:
-
enumerator kDCP_Sha1
SHA_1
-
enumerator kDCP_Sha256
SHA_256
-
enumerator kDCP_Crc32
CRC_32
-
enumerator kDCP_Sha1
-
typedef enum _dcp_hash_algo_t dcp_hash_algo_t
Supported cryptographic block cipher functions for HASH creation.
-
typedef struct _dcp_hash_ctx_t dcp_hash_ctx_t
Storage type used to save hash context.
-
status_t DCP_HASH_Init(DCP_Type *base, dcp_handle_t *handle, dcp_hash_ctx_t *ctx, dcp_hash_algo_t algo)
Initialize HASH context.
This function initializes the HASH.
- Parameters:
base – DCP peripheral base address
handle – Specifies the DCP channel used for hashing.
ctx – [out] Output hash context
algo – Underlaying algorithm to use for hash computation.
- Returns:
Status of initialization
-
status_t DCP_HASH_Update(DCP_Type *base, dcp_hash_ctx_t *ctx, const uint8_t *input, size_t inputSize)
Add data to current HASH.
Add data to current HASH. This can be called repeatedly with an arbitrary amount of data to be hashed. The functions blocks. If it returns kStatus_Success, the running hash has been updated (DCP has processed the input data), so the memory at the input pointer can be released back to system. The DCP context buffer is updated with the running hash and with all necessary information to support possible context switch.
- Parameters:
base – DCP peripheral base address
ctx – [inout] HASH context
input – Input data
inputSize – Size of input data in bytes
- Returns:
Status of the hash update operation
-
status_t DCP_HASH_Finish(DCP_Type *base, dcp_hash_ctx_t *ctx, uint8_t *output, size_t *outputSize)
Finalize hashing.
Outputs the final hash (computed by DCP_HASH_Update()) and erases the context.
- Parameters:
base – DCP peripheral base address
ctx – [inout] Input hash context
output – [out] Output hash data
outputSize – [inout] Optional parameter (can be passed as NULL). On function entry, it specifies the size of output[] buffer. On function return, it stores the number of updated output bytes.
- Returns:
Status of the hash finish operation
-
status_t DCP_HASH(DCP_Type *base, dcp_handle_t *handle, dcp_hash_algo_t algo, const uint8_t *input, size_t inputSize, uint8_t *output, size_t *outputSize)
Create HASH on given data.
Perform the full SHA or CRC32 in one function call. The function is blocking.
- Parameters:
base – DCP peripheral base address
handle – Handle used for the request.
algo – Underlaying algorithm to use for hash computation.
input – Input data
inputSize – Size of input data in bytes
output – [out] Output hash data
outputSize – [out] Output parameter storing the size of the output hash in bytes
- Returns:
Status of the one call hash operation.
-
DCP_HASH_CAVP_COMPATIBLE
-
DCP_SHA_BLOCK_SIZE
DCP HASH Context size.
internal buffer block size
-
DCP_HASH_BLOCK_SIZE
DCP hash block size
-
DCP_HASH_CTX_SIZE
DCP HASH Context size.
-
struct _dcp_hash_ctx_t
- #include <fsl_dcp.h>
Storage type used to save hash context.
DCP AES non-blocking driver
-
status_t DCP_AES_EncryptEcbNonBlocking(DCP_Type *base, dcp_handle_t *handle, dcp_work_packet_t *dcpPacket, const uint8_t *plaintext, uint8_t *ciphertext, size_t size)
Encrypts AES using the ECB block mode.
Puts AES ECB encrypt work packet to DCP channel.
- Parameters:
base – DCP peripheral base address
handle – Handle used for this request.
dcpPacket – [out] Memory for the DCP work packet.
plaintext – Input plain text to encrypt.
ciphertext – [out] Output cipher text
size – Size of input and output data in bytes. Must be multiple of 16 bytes.
- Returns:
kStatus_Success The work packet has been scheduled at DCP channel.
- Returns:
kStatus_DCP_Again The DCP channel is busy processing previous request.
-
status_t DCP_AES_DecryptEcbNonBlocking(DCP_Type *base, dcp_handle_t *handle, dcp_work_packet_t *dcpPacket, const uint8_t *ciphertext, uint8_t *plaintext, size_t size)
Decrypts AES using ECB block mode.
Puts AES ECB decrypt dcpPacket to DCP input job ring.
- Parameters:
base – DCP peripheral base address
handle – Handle used for this request.
dcpPacket – [out] Memory for the DCP work packet.
ciphertext – Input cipher text to decrypt
plaintext – [out] Output plain text
size – Size of input and output data in bytes. Must be multiple of 16 bytes.
- Returns:
kStatus_Success The work packet has been scheduled at DCP channel.
- Returns:
kStatus_DCP_Again The DCP channel is busy processing previous request.
-
status_t DCP_AES_EncryptCbcNonBlocking(DCP_Type *base, dcp_handle_t *handle, dcp_work_packet_t *dcpPacket, const uint8_t *plaintext, uint8_t *ciphertext, size_t size, const uint8_t *iv)
Encrypts AES using CBC block mode.
Puts AES CBC encrypt dcpPacket to DCP input job ring.
- Parameters:
base – DCP peripheral base address
handle – Handle used for this request. Specifies jobRing.
dcpPacket – [out] Memory for the DCP work packet.
plaintext – Input plain text to encrypt
ciphertext – [out] Output cipher text
size – Size of input and output data in bytes. Must be multiple of 16 bytes.
iv – Input initial vector to combine with the first input block.
- Returns:
kStatus_Success The work packet has been scheduled at DCP channel.
- Returns:
kStatus_DCP_Again The DCP channel is busy processing previous request.
-
status_t DCP_AES_DecryptCbcNonBlocking(DCP_Type *base, dcp_handle_t *handle, dcp_work_packet_t *dcpPacket, const uint8_t *ciphertext, uint8_t *plaintext, size_t size, const uint8_t *iv)
Decrypts AES using CBC block mode.
Puts AES CBC decrypt dcpPacket to DCP input job ring.
- Parameters:
base – DCP peripheral base address
handle – Handle used for this request. Specifies jobRing.
dcpPacket – [out] Memory for the DCP work packet.
ciphertext – Input cipher text to decrypt
plaintext – [out] Output plain text
size – Size of input and output data in bytes. Must be multiple of 16 bytes.
iv – Input initial vector to combine with the first input block.
- Returns:
kStatus_Success The work packet has been scheduled at DCP channel.
- Returns:
kStatus_DCP_Again The DCP channel is busy processing previous request.
DMAMUX: Direct Memory Access Multiplexer Driver
-
void DMAMUX_Init(DMAMUX_Type *base)
Initializes the DMAMUX peripheral.
This function ungates the DMAMUX clock.
- Parameters:
base – DMAMUX peripheral base address.
-
void DMAMUX_Deinit(DMAMUX_Type *base)
Deinitializes the DMAMUX peripheral.
This function gates the DMAMUX clock.
- Parameters:
base – DMAMUX peripheral base address.
-
static inline void DMAMUX_EnableChannel(DMAMUX_Type *base, uint32_t channel)
Enables the DMAMUX channel.
This function enables the DMAMUX channel.
- Parameters:
base – DMAMUX peripheral base address.
channel – DMAMUX channel number.
-
static inline void DMAMUX_DisableChannel(DMAMUX_Type *base, uint32_t channel)
Disables the DMAMUX channel.
This function disables the DMAMUX channel.
Note
The user must disable the DMAMUX channel before configuring it.
- Parameters:
base – DMAMUX peripheral base address.
channel – DMAMUX channel number.
-
static inline void DMAMUX_SetSource(DMAMUX_Type *base, uint32_t channel, int32_t source)
Configures the DMAMUX channel source.
- Parameters:
base – DMAMUX peripheral base address.
channel – DMAMUX channel number.
source – Channel source, which is used to trigger the DMA transfer.User need to use the dma_request_source_t type as the input parameter.
-
static inline void DMAMUX_EnablePeriodTrigger(DMAMUX_Type *base, uint32_t channel)
Enables the DMAMUX period trigger.
This function enables the DMAMUX period trigger feature.
- Parameters:
base – DMAMUX peripheral base address.
channel – DMAMUX channel number.
-
static inline void DMAMUX_DisablePeriodTrigger(DMAMUX_Type *base, uint32_t channel)
Disables the DMAMUX period trigger.
This function disables the DMAMUX period trigger.
- Parameters:
base – DMAMUX peripheral base address.
channel – DMAMUX channel number.
-
static inline void DMAMUX_EnableAlwaysOn(DMAMUX_Type *base, uint32_t channel, bool enable)
Enables the DMA channel to be always ON.
This function enables the DMAMUX channel always ON feature.
- Parameters:
base – DMAMUX peripheral base address.
channel – DMAMUX channel number.
enable – Switcher of the always ON feature. “true” means enabled, “false” means disabled.
-
FSL_DMAMUX_DRIVER_VERSION
DMAMUX driver version 2.1.0.
eDMA: Enhanced Direct Memory Access (eDMA) Controller Driver
-
void EDMA_Init(DMA_Type *base, const edma_config_t *config)
Initializes the eDMA peripheral.
This function ungates the eDMA clock and configures the eDMA peripheral according to the configuration structure. All emda enabled request will be cleared in this function.
Note
This function enables the minor loop map feature.
- Parameters:
base – eDMA peripheral base address.
config – A pointer to the configuration structure, see “edma_config_t”.
-
void EDMA_Deinit(DMA_Type *base)
Deinitializes the eDMA peripheral.
This function gates the eDMA clock.
- Parameters:
base – eDMA peripheral base address.
-
void EDMA_InstallTCD(DMA_Type *base, uint32_t channel, edma_tcd_t *tcd)
Push content of TCD structure into hardware TCD register.
- Parameters:
base – EDMA peripheral base address.
channel – EDMA channel number.
tcd – Point to TCD structure.
-
void EDMA_GetDefaultConfig(edma_config_t *config)
Gets the eDMA default configuration structure.
This function sets the configuration structure to default values. The default configuration is set to the following values.
config.enableContinuousLinkMode = false; config.enableHaltOnError = true; config.enableRoundRobinArbitration = false; config.enableDebugMode = false;
- Parameters:
config – A pointer to the eDMA configuration structure.
-
static inline void EDMA_EnableContinuousChannelLinkMode(DMA_Type *base, bool enable)
Enable/Disable continuous channel link mode.
Note
Do not use continuous link mode with a channel linking to itself if there is only one minor loop iteration per service request, for example, if the channel’s NBYTES value is the same as either the source or destination size. The same data transfer profile can be achieved by simply increasing the NBYTES value, which provides more efficient, faster processing.
- Parameters:
base – EDMA peripheral base address.
enable – true is enable, false is disable.
-
static inline void EDMA_EnableMinorLoopMapping(DMA_Type *base, bool enable)
Enable/Disable minor loop mapping.
The TCDn.word2 is redefined to include individual enable fields, an offset field, and the NBYTES field.
- Parameters:
base – EDMA peripheral base address.
enable – true is enable, false is disable.
-
void EDMA_ResetChannel(DMA_Type *base, uint32_t channel)
Sets all TCD registers to default values.
This function sets TCD registers for this channel to default values.
Note
This function must not be called while the channel transfer is ongoing or it causes unpredictable results.
Note
This function enables the auto stop request feature.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
-
void EDMA_SetTransferConfig(DMA_Type *base, uint32_t channel, const edma_transfer_config_t *config, edma_tcd_t *nextTcd)
Configures the eDMA transfer attribute.
This function configures the transfer attribute, including source address, destination address, transfer size, address offset, and so on. It also configures the scatter gather feature if the user supplies the TCD address. Example:
edma_transfer_t config; edma_tcd_t tcd; config.srcAddr = ..; config.destAddr = ..; ... EDMA_SetTransferConfig(DMA0, channel, &config, &stcd);
Note
If nextTcd is not NULL, it means scatter gather feature is enabled and DREQ bit is cleared in the previous transfer configuration, which is set in the eDMA_ResetChannel.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
config – Pointer to eDMA transfer configuration structure.
nextTcd – Point to TCD structure. It can be NULL if users do not want to enable scatter/gather feature.
-
void EDMA_SetMinorOffsetConfig(DMA_Type *base, uint32_t channel, const edma_minor_offset_config_t *config)
Configures the eDMA minor offset feature.
The minor offset means that the signed-extended value is added to the source address or destination address after each minor loop.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
config – A pointer to the minor offset configuration structure.
-
void EDMA_SetChannelPreemptionConfig(DMA_Type *base, uint32_t channel, const edma_channel_Preemption_config_t *config)
Configures the eDMA channel preemption feature.
This function configures the channel preemption attribute and the priority of the channel.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number
config – A pointer to the channel preemption configuration structure.
-
void EDMA_SetChannelLink(DMA_Type *base, uint32_t channel, edma_channel_link_type_t linkType, uint32_t linkedChannel)
Sets the channel link for the eDMA transfer.
This function configures either the minor link or the major link mode. The minor link means that the channel link is triggered every time CITER decreases by 1. The major link means that the channel link is triggered when the CITER is exhausted.
Note
Users should ensure that DONE flag is cleared before calling this interface, or the configuration is invalid.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
linkType – A channel link type, which can be one of the following:
kEDMA_LinkNone
kEDMA_MinorLink
kEDMA_MajorLink
linkedChannel – The linked channel number.
-
void EDMA_SetBandWidth(DMA_Type *base, uint32_t channel, edma_bandwidth_t bandWidth)
Sets the bandwidth for the eDMA transfer.
Because the eDMA processes the minor loop, it continuously generates read/write sequences until the minor count is exhausted. The bandwidth forces the eDMA to stall after the completion of each read/write access to control the bus request bandwidth seen by the crossbar switch.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
bandWidth – A bandwidth setting, which can be one of the following:
kEDMABandwidthStallNone
kEDMABandwidthStall4Cycle
kEDMABandwidthStall8Cycle
-
void EDMA_SetModulo(DMA_Type *base, uint32_t channel, edma_modulo_t srcModulo, edma_modulo_t destModulo)
Sets the source modulo and the destination modulo for the eDMA transfer.
This function defines a specific address range specified to be the value after (SADDR + SOFF)/(DADDR + DOFF) calculation is performed or the original register value. It provides the ability to implement a circular data queue easily.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
srcModulo – A source modulo value.
destModulo – A destination modulo value.
-
static inline void EDMA_EnableAsyncRequest(DMA_Type *base, uint32_t channel, bool enable)
Enables an async request for the eDMA transfer.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
enable – The command to enable (true) or disable (false).
-
static inline void EDMA_EnableAutoStopRequest(DMA_Type *base, uint32_t channel, bool enable)
Enables an auto stop request for the eDMA transfer.
If enabling the auto stop request, the eDMA hardware automatically disables the hardware channel request.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
enable – The command to enable (true) or disable (false).
-
void EDMA_EnableChannelInterrupts(DMA_Type *base, uint32_t channel, uint32_t mask)
Enables the interrupt source for the eDMA transfer.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
mask – The mask of interrupt source to be set. Users need to use the defined edma_interrupt_enable_t type.
-
void EDMA_DisableChannelInterrupts(DMA_Type *base, uint32_t channel, uint32_t mask)
Disables the interrupt source for the eDMA transfer.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
mask – The mask of the interrupt source to be set. Use the defined edma_interrupt_enable_t type.
-
void EDMA_SetMajorOffsetConfig(DMA_Type *base, uint32_t channel, int32_t sourceOffset, int32_t destOffset)
Configures the eDMA channel TCD major offset feature.
Adjustment value added to the source address at the completion of the major iteration count
- Parameters:
base – eDMA peripheral base address.
channel – edma channel number.
sourceOffset – source address offset will be applied to source address after major loop done.
destOffset – destination address offset will be applied to source address after major loop done.
-
void EDMA_TcdReset(edma_tcd_t *tcd)
Sets all fields to default values for the TCD structure.
This function sets all fields for this TCD structure to default value.
Note
This function enables the auto stop request feature.
- Parameters:
tcd – Pointer to the TCD structure.
-
void EDMA_TcdSetTransferConfig(edma_tcd_t *tcd, const edma_transfer_config_t *config, edma_tcd_t *nextTcd)
Configures the eDMA TCD transfer attribute.
The TCD is a transfer control descriptor. The content of the TCD is the same as the hardware TCD registers. The TCD is used in the scatter-gather mode. This function configures the TCD transfer attribute, including source address, destination address, transfer size, address offset, and so on. It also configures the scatter gather feature if the user supplies the next TCD address. Example:
edma_transfer_t config = { ... } edma_tcd_t tcd __aligned(32); edma_tcd_t nextTcd __aligned(32); EDMA_TcdSetTransferConfig(&tcd, &config, &nextTcd);
Note
TCD address should be 32 bytes aligned or it causes an eDMA error.
Note
If the nextTcd is not NULL, the scatter gather feature is enabled and DREQ bit is cleared in the previous transfer configuration, which is set in the EDMA_TcdReset.
- Parameters:
tcd – Pointer to the TCD structure.
config – Pointer to eDMA transfer configuration structure.
nextTcd – Pointer to the next TCD structure. It can be NULL if users do not want to enable scatter/gather feature.
-
void EDMA_TcdSetMinorOffsetConfig(edma_tcd_t *tcd, const edma_minor_offset_config_t *config)
Configures the eDMA TCD minor offset feature.
A minor offset is a signed-extended value added to the source address or a destination address after each minor loop.
- Parameters:
tcd – A point to the TCD structure.
config – A pointer to the minor offset configuration structure.
-
void EDMA_TcdSetChannelLink(edma_tcd_t *tcd, edma_channel_link_type_t linkType, uint32_t linkedChannel)
Sets the channel link for the eDMA TCD.
This function configures either a minor link or a major link. The minor link means the channel link is triggered every time CITER decreases by 1. The major link means that the channel link is triggered when the CITER is exhausted.
Note
Users should ensure that DONE flag is cleared before calling this interface, or the configuration is invalid.
- Parameters:
tcd – Point to the TCD structure.
linkType – Channel link type, it can be one of:
kEDMA_LinkNone
kEDMA_MinorLink
kEDMA_MajorLink
linkedChannel – The linked channel number.
-
static inline void EDMA_TcdSetBandWidth(edma_tcd_t *tcd, edma_bandwidth_t bandWidth)
Sets the bandwidth for the eDMA TCD.
Because the eDMA processes the minor loop, it continuously generates read/write sequences until the minor count is exhausted. The bandwidth forces the eDMA to stall after the completion of each read/write access to control the bus request bandwidth seen by the crossbar switch.
- Parameters:
tcd – A pointer to the TCD structure.
bandWidth – A bandwidth setting, which can be one of the following:
kEDMABandwidthStallNone
kEDMABandwidthStall4Cycle
kEDMABandwidthStall8Cycle
-
void EDMA_TcdSetModulo(edma_tcd_t *tcd, edma_modulo_t srcModulo, edma_modulo_t destModulo)
Sets the source modulo and the destination modulo for the eDMA TCD.
This function defines a specific address range specified to be the value after (SADDR + SOFF)/(DADDR + DOFF) calculation is performed or the original register value. It provides the ability to implement a circular data queue easily.
- Parameters:
tcd – A pointer to the TCD structure.
srcModulo – A source modulo value.
destModulo – A destination modulo value.
-
static inline void EDMA_TcdEnableAutoStopRequest(edma_tcd_t *tcd, bool enable)
Sets the auto stop request for the eDMA TCD.
If enabling the auto stop request, the eDMA hardware automatically disables the hardware channel request.
- Parameters:
tcd – A pointer to the TCD structure.
enable – The command to enable (true) or disable (false).
-
void EDMA_TcdEnableInterrupts(edma_tcd_t *tcd, uint32_t mask)
Enables the interrupt source for the eDMA TCD.
- Parameters:
tcd – Point to the TCD structure.
mask – The mask of interrupt source to be set. Users need to use the defined edma_interrupt_enable_t type.
-
void EDMA_TcdDisableInterrupts(edma_tcd_t *tcd, uint32_t mask)
Disables the interrupt source for the eDMA TCD.
- Parameters:
tcd – Point to the TCD structure.
mask – The mask of interrupt source to be set. Users need to use the defined edma_interrupt_enable_t type.
-
void EDMA_TcdSetMajorOffsetConfig(edma_tcd_t *tcd, int32_t sourceOffset, int32_t destOffset)
Configures the eDMA TCD major offset feature.
Adjustment value added to the source address at the completion of the major iteration count
- Parameters:
tcd – A point to the TCD structure.
sourceOffset – source address offset wiil be applied to source address after major loop done.
destOffset – destination address offset will be applied to source address after major loop done.
-
static inline void EDMA_EnableChannelRequest(DMA_Type *base, uint32_t channel)
Enables the eDMA hardware channel request.
This function enables the hardware channel request.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
-
static inline void EDMA_DisableChannelRequest(DMA_Type *base, uint32_t channel)
Disables the eDMA hardware channel request.
This function disables the hardware channel request.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
-
static inline void EDMA_TriggerChannelStart(DMA_Type *base, uint32_t channel)
Starts the eDMA transfer by using the software trigger.
This function starts a minor loop transfer.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
-
uint32_t EDMA_GetRemainingMajorLoopCount(DMA_Type *base, uint32_t channel)
Gets the remaining major loop count from the eDMA current channel TCD.
This function checks the TCD (Task Control Descriptor) status for a specified eDMA channel and returns the number of major loop count that has not finished.
Note
1. This function can only be used to get unfinished major loop count of transfer without the next TCD, or it might be inaccuracy.
The unfinished/remaining transfer bytes cannot be obtained directly from registers while the channel is running. Because to calculate the remaining bytes, the initial NBYTES configured in DMA_TCDn_NBYTES_MLNO register is needed while the eDMA IP does not support getting it while a channel is active. In another word, the NBYTES value reading is always the actual (decrementing) NBYTES value the dma_engine is working with while a channel is running. Consequently, to get the remaining transfer bytes, a software-saved initial value of NBYTES (for example copied before enabling the channel) is needed. The formula to calculate it is shown below: RemainingBytes = RemainingMajorLoopCount * NBYTES(initially configured)
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
- Returns:
Major loop count which has not been transferred yet for the current TCD.
-
static inline uint32_t EDMA_GetErrorStatusFlags(DMA_Type *base)
Gets the eDMA channel error status flags.
- Parameters:
base – eDMA peripheral base address.
- Returns:
The mask of error status flags. Users need to use the _edma_error_status_flags type to decode the return variables.
-
uint32_t EDMA_GetChannelStatusFlags(DMA_Type *base, uint32_t channel)
Gets the eDMA channel status flags.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
- Returns:
The mask of channel status flags. Users need to use the _edma_channel_status_flags type to decode the return variables.
-
void EDMA_ClearChannelStatusFlags(DMA_Type *base, uint32_t channel, uint32_t mask)
Clears the eDMA channel status flags.
- Parameters:
base – eDMA peripheral base address.
channel – eDMA channel number.
mask – The mask of channel status to be cleared. Users need to use the defined _edma_channel_status_flags type.
-
void EDMA_CreateHandle(edma_handle_t *handle, DMA_Type *base, uint32_t channel)
Creates the eDMA handle.
This function is called if using the transactional API for eDMA. This function initializes the internal state of the eDMA handle.
- Parameters:
handle – eDMA handle pointer. The eDMA handle stores callback function and parameters.
base – eDMA peripheral base address.
channel – eDMA channel number.
-
void EDMA_InstallTCDMemory(edma_handle_t *handle, edma_tcd_t *tcdPool, uint32_t tcdSize)
Installs the TCDs memory pool into the eDMA handle.
This function is called after the EDMA_CreateHandle to use scatter/gather feature. This function shall only be used while users need to use scatter gather mode. Scatter gather mode enables EDMA to load a new transfer control block (tcd) in hardware, and automatically reconfigure that DMA channel for a new transfer. Users need to prepare tcd memory and also configure tcds using interface EDMA_SubmitTransfer.
- Parameters:
handle – eDMA handle pointer.
tcdPool – A memory pool to store TCDs. It must be 32 bytes aligned.
tcdSize – The number of TCD slots.
-
void EDMA_SetCallback(edma_handle_t *handle, edma_callback callback, void *userData)
Installs a callback function for the eDMA transfer.
This callback is called in the eDMA IRQ handler. Use the callback to do something after the current major loop transfer completes. This function will be called every time one tcd finished transfer.
- Parameters:
handle – eDMA handle pointer.
callback – eDMA callback function pointer.
userData – A parameter for the callback function.
-
void EDMA_PrepareTransferConfig(edma_transfer_config_t *config, void *srcAddr, uint32_t srcWidth, int16_t srcOffset, void *destAddr, uint32_t destWidth, int16_t destOffset, uint32_t bytesEachRequest, uint32_t transferBytes)
Prepares the eDMA transfer structure configurations.
This function prepares the transfer configuration structure according to the user input.
Note
The data address and the data width must be consistent. For example, if the SRC is 4 bytes, the source address must be 4 bytes aligned, or it results in source address error (SAE).
- Parameters:
config – The user configuration structure of type edma_transfer_t.
srcAddr – eDMA transfer source address.
srcWidth – eDMA transfer source address width(bytes).
srcOffset – source address offset.
destAddr – eDMA transfer destination address.
destWidth – eDMA transfer destination address width(bytes).
destOffset – destination address offset.
bytesEachRequest – eDMA transfer bytes per channel request.
transferBytes – eDMA transfer bytes to be transferred.
-
void EDMA_PrepareTransfer(edma_transfer_config_t *config, void *srcAddr, uint32_t srcWidth, void *destAddr, uint32_t destWidth, uint32_t bytesEachRequest, uint32_t transferBytes, edma_transfer_type_t transferType)
Prepares the eDMA transfer structure.
This function prepares the transfer configuration structure according to the user input.
Note
The data address and the data width must be consistent. For example, if the SRC is 4 bytes, the source address must be 4 bytes aligned, or it results in source address error (SAE).
- Parameters:
config – The user configuration structure of type edma_transfer_t.
srcAddr – eDMA transfer source address.
srcWidth – eDMA transfer source address width(bytes).
destAddr – eDMA transfer destination address.
destWidth – eDMA transfer destination address width(bytes).
bytesEachRequest – eDMA transfer bytes per channel request.
transferBytes – eDMA transfer bytes to be transferred.
transferType – eDMA transfer type.
-
status_t EDMA_SubmitTransfer(edma_handle_t *handle, const edma_transfer_config_t *config)
Submits the eDMA transfer request.
This function submits the eDMA transfer request according to the transfer configuration structure. In scatter gather mode, call this function will add a configured tcd to the circular list of tcd pool. The tcd pools is setup by call function EDMA_InstallTCDMemory before.
- Parameters:
handle – eDMA handle pointer.
config – Pointer to eDMA transfer configuration structure.
- Return values:
kStatus_EDMA_Success – It means submit transfer request succeed.
kStatus_EDMA_QueueFull – It means TCD queue is full. Submit transfer request is not allowed.
kStatus_EDMA_Busy – It means the given channel is busy, need to submit request later.
-
void EDMA_StartTransfer(edma_handle_t *handle)
eDMA starts transfer.
This function enables the channel request. Users can call this function after submitting the transfer request or before submitting the transfer request.
- Parameters:
handle – eDMA handle pointer.
-
void EDMA_StopTransfer(edma_handle_t *handle)
eDMA stops transfer.
This function disables the channel request to pause the transfer. Users can call EDMA_StartTransfer() again to resume the transfer.
- Parameters:
handle – eDMA handle pointer.
-
void EDMA_AbortTransfer(edma_handle_t *handle)
eDMA aborts transfer.
This function disables the channel request and clear transfer status bits. Users can submit another transfer after calling this API.
- Parameters:
handle – DMA handle pointer.
-
static inline uint32_t EDMA_GetUnusedTCDNumber(edma_handle_t *handle)
Get unused TCD slot number.
This function gets current tcd index which is run. If the TCD pool pointer is NULL, it will return 0.
- Parameters:
handle – DMA handle pointer.
- Returns:
The unused tcd slot number.
-
static inline uint32_t EDMA_GetNextTCDAddress(edma_handle_t *handle)
Get the next tcd address.
This function gets the next tcd address. If this is last TCD, return 0.
- Parameters:
handle – DMA handle pointer.
- Returns:
The next TCD address.
-
void EDMA_HandleIRQ(edma_handle_t *handle)
eDMA IRQ handler for the current major loop transfer completion.
This function clears the channel major interrupt flag and calls the callback function if it is not NULL.
Note: For the case using TCD queue, when the major iteration count is exhausted, additional operations are performed. These include the final address adjustments and reloading of the BITER field into the CITER. Assertion of an optional interrupt request also occurs at this time, as does a possible fetch of a new TCD from memory using the scatter/gather address pointer included in the descriptor (if scatter/gather is enabled).
For instance, when the time interrupt of TCD[0] happens, the TCD[1] has already been loaded into the eDMA engine. As sga and sga_index are calculated based on the DLAST_SGA bitfield lies in the TCD_CSR register, the sga_index in this case should be 2 (DLAST_SGA of TCD[1] stores the address of TCD[2]). Thus, the “tcdUsed” updated should be (tcdUsed - 2U) which indicates the number of TCDs can be loaded in the memory pool (because TCD[0] and TCD[1] have been loaded into the eDMA engine at this point already.).
For the last two continuous ISRs in a scatter/gather process, they both load the last TCD (The last ISR does not load a new TCD) from the memory pool to the eDMA engine when major loop completes. Therefore, ensure that the header and tcdUsed updated are identical for them. tcdUsed are both 0 in this case as no TCD to be loaded.
See the “eDMA basic data flow” in the eDMA Functional description section of the Reference Manual for further details.
- Parameters:
handle – eDMA handle pointer.
-
FSL_EDMA_DRIVER_VERSION
eDMA driver version
Version 2.4.4.
-
enum _edma_transfer_size
eDMA transfer configuration
Values:
-
enumerator kEDMA_TransferSize1Bytes
Source/Destination data transfer size is 1 byte every time
-
enumerator kEDMA_TransferSize2Bytes
Source/Destination data transfer size is 2 bytes every time
-
enumerator kEDMA_TransferSize4Bytes
Source/Destination data transfer size is 4 bytes every time
-
enumerator kEDMA_TransferSize8Bytes
Source/Destination data transfer size is 8 bytes every time
-
enumerator kEDMA_TransferSize16Bytes
Source/Destination data transfer size is 16 bytes every time
-
enumerator kEDMA_TransferSize32Bytes
Source/Destination data transfer size is 32 bytes every time
-
enumerator kEDMA_TransferSize1Bytes
-
enum _edma_modulo
eDMA modulo configuration
Values:
-
enumerator kEDMA_ModuloDisable
Disable modulo
-
enumerator kEDMA_Modulo2bytes
Circular buffer size is 2 bytes.
-
enumerator kEDMA_Modulo4bytes
Circular buffer size is 4 bytes.
-
enumerator kEDMA_Modulo8bytes
Circular buffer size is 8 bytes.
-
enumerator kEDMA_Modulo16bytes
Circular buffer size is 16 bytes.
-
enumerator kEDMA_Modulo32bytes
Circular buffer size is 32 bytes.
-
enumerator kEDMA_Modulo64bytes
Circular buffer size is 64 bytes.
-
enumerator kEDMA_Modulo128bytes
Circular buffer size is 128 bytes.
-
enumerator kEDMA_Modulo256bytes
Circular buffer size is 256 bytes.
-
enumerator kEDMA_Modulo512bytes
Circular buffer size is 512 bytes.
-
enumerator kEDMA_Modulo1Kbytes
Circular buffer size is 1 K bytes.
-
enumerator kEDMA_Modulo2Kbytes
Circular buffer size is 2 K bytes.
-
enumerator kEDMA_Modulo4Kbytes
Circular buffer size is 4 K bytes.
-
enumerator kEDMA_Modulo8Kbytes
Circular buffer size is 8 K bytes.
-
enumerator kEDMA_Modulo16Kbytes
Circular buffer size is 16 K bytes.
-
enumerator kEDMA_Modulo32Kbytes
Circular buffer size is 32 K bytes.
-
enumerator kEDMA_Modulo64Kbytes
Circular buffer size is 64 K bytes.
-
enumerator kEDMA_Modulo128Kbytes
Circular buffer size is 128 K bytes.
-
enumerator kEDMA_Modulo256Kbytes
Circular buffer size is 256 K bytes.
-
enumerator kEDMA_Modulo512Kbytes
Circular buffer size is 512 K bytes.
-
enumerator kEDMA_Modulo1Mbytes
Circular buffer size is 1 M bytes.
-
enumerator kEDMA_Modulo2Mbytes
Circular buffer size is 2 M bytes.
-
enumerator kEDMA_Modulo4Mbytes
Circular buffer size is 4 M bytes.
-
enumerator kEDMA_Modulo8Mbytes
Circular buffer size is 8 M bytes.
-
enumerator kEDMA_Modulo16Mbytes
Circular buffer size is 16 M bytes.
-
enumerator kEDMA_Modulo32Mbytes
Circular buffer size is 32 M bytes.
-
enumerator kEDMA_Modulo64Mbytes
Circular buffer size is 64 M bytes.
-
enumerator kEDMA_Modulo128Mbytes
Circular buffer size is 128 M bytes.
-
enumerator kEDMA_Modulo256Mbytes
Circular buffer size is 256 M bytes.
-
enumerator kEDMA_Modulo512Mbytes
Circular buffer size is 512 M bytes.
-
enumerator kEDMA_Modulo1Gbytes
Circular buffer size is 1 G bytes.
-
enumerator kEDMA_Modulo2Gbytes
Circular buffer size is 2 G bytes.
-
enumerator kEDMA_ModuloDisable
-
enum _edma_bandwidth
Bandwidth control.
Values:
-
enumerator kEDMA_BandwidthStallNone
No eDMA engine stalls.
-
enumerator kEDMA_BandwidthStall4Cycle
eDMA engine stalls for 4 cycles after each read/write.
-
enumerator kEDMA_BandwidthStall8Cycle
eDMA engine stalls for 8 cycles after each read/write.
-
enumerator kEDMA_BandwidthStallNone
-
enum _edma_channel_link_type
Channel link type.
Values:
-
enumerator kEDMA_LinkNone
No channel link
-
enumerator kEDMA_MinorLink
Channel link after each minor loop
-
enumerator kEDMA_MajorLink
Channel link while major loop count exhausted
-
enumerator kEDMA_LinkNone
_edma_channel_status_flags eDMA channel status flags.
Values:
-
enumerator kEDMA_DoneFlag
DONE flag, set while transfer finished, CITER value exhausted
-
enumerator kEDMA_ErrorFlag
eDMA error flag, an error occurred in a transfer
-
enumerator kEDMA_InterruptFlag
eDMA interrupt flag, set while an interrupt occurred of this channel
-
enumerator kEDMA_DoneFlag
_edma_error_status_flags eDMA channel error status flags.
Values:
-
enumerator kEDMA_DestinationBusErrorFlag
Bus error on destination address
-
enumerator kEDMA_SourceBusErrorFlag
Bus error on the source address
-
enumerator kEDMA_ScatterGatherErrorFlag
Error on the Scatter/Gather address, not 32byte aligned.
-
enumerator kEDMA_NbytesErrorFlag
NBYTES/CITER configuration error
-
enumerator kEDMA_DestinationOffsetErrorFlag
Destination offset not aligned with destination size
-
enumerator kEDMA_DestinationAddressErrorFlag
Destination address not aligned with destination size
-
enumerator kEDMA_SourceOffsetErrorFlag
Source offset not aligned with source size
-
enumerator kEDMA_SourceAddressErrorFlag
Source address not aligned with source size
-
enumerator kEDMA_ErrorChannelFlag
Error channel number of the cancelled channel number
-
enumerator kEDMA_ChannelPriorityErrorFlag
Channel priority is not unique.
-
enumerator kEDMA_TransferCanceledFlag
Transfer cancelled
-
enumerator kEDMA_ValidFlag
No error occurred, this bit is 0. Otherwise, it is 1.
-
enumerator kEDMA_DestinationBusErrorFlag
-
enum _edma_interrupt_enable
eDMA interrupt source
Values:
-
enumerator kEDMA_ErrorInterruptEnable
Enable interrupt while channel error occurs.
-
enumerator kEDMA_MajorInterruptEnable
Enable interrupt while major count exhausted.
-
enumerator kEDMA_HalfInterruptEnable
Enable interrupt while major count to half value.
-
enumerator kEDMA_ErrorInterruptEnable
-
enum _edma_transfer_type
eDMA transfer type
Values:
-
enumerator kEDMA_MemoryToMemory
Transfer from memory to memory
-
enumerator kEDMA_PeripheralToMemory
Transfer from peripheral to memory
-
enumerator kEDMA_MemoryToPeripheral
Transfer from memory to peripheral
-
enumerator kEDMA_PeripheralToPeripheral
Transfer from Peripheral to peripheral
-
enumerator kEDMA_MemoryToMemory
_edma_transfer_status eDMA transfer status
Values:
-
enumerator kStatus_EDMA_QueueFull
TCD queue is full.
-
enumerator kStatus_EDMA_Busy
Channel is busy and can’t handle the transfer request.
-
enumerator kStatus_EDMA_QueueFull
-
typedef enum _edma_transfer_size edma_transfer_size_t
eDMA transfer configuration
-
typedef enum _edma_modulo edma_modulo_t
eDMA modulo configuration
-
typedef enum _edma_bandwidth edma_bandwidth_t
Bandwidth control.
-
typedef enum _edma_channel_link_type edma_channel_link_type_t
Channel link type.
-
typedef enum _edma_interrupt_enable edma_interrupt_enable_t
eDMA interrupt source
-
typedef enum _edma_transfer_type edma_transfer_type_t
eDMA transfer type
-
typedef struct _edma_config edma_config_t
eDMA global configuration structure.
-
typedef struct _edma_transfer_config edma_transfer_config_t
eDMA transfer configuration
This structure configures the source/destination transfer attribute.
-
typedef struct _edma_channel_Preemption_config edma_channel_Preemption_config_t
eDMA channel priority configuration
-
typedef struct _edma_minor_offset_config edma_minor_offset_config_t
eDMA minor offset configuration
-
typedef struct _edma_tcd edma_tcd_t
eDMA TCD.
This structure is same as TCD register which is described in reference manual, and is used to configure the scatter/gather feature as a next hardware TCD.
-
typedef void (*edma_callback)(struct _edma_handle *handle, void *userData, bool transferDone, uint32_t tcds)
Define callback function for eDMA.
This callback function is called in the EDMA interrupt handle. In normal mode, run into callback function means the transfer users need is done. In scatter gather mode, run into callback function means a transfer control block (tcd) is finished. Not all transfer finished, users can get the finished tcd numbers using interface EDMA_GetUnusedTCDNumber.
- Param handle:
EDMA handle pointer, users shall not touch the values inside.
- Param userData:
The callback user parameter pointer. Users can use this parameter to involve things users need to change in EDMA callback function.
- Param transferDone:
If the current loaded transfer done. In normal mode it means if all transfer done. In scatter gather mode, this parameter shows is the current transfer block in EDMA register is done. As the load of core is different, it will be different if the new tcd loaded into EDMA registers while this callback called. If true, it always means new tcd still not loaded into registers, while false means new tcd already loaded into registers.
- Param tcds:
How many tcds are done from the last callback. This parameter only used in scatter gather mode. It tells user how many tcds are finished between the last callback and this.
-
typedef struct _edma_handle edma_handle_t
eDMA transfer handle structure
-
DMA_DCHPRI_INDEX(channel)
Compute the offset unit from DCHPRI3.
-
struct _edma_config
- #include <fsl_edma.h>
eDMA global configuration structure.
Public Members
-
bool enableContinuousLinkMode
Enable (true) continuous link mode. Upon minor loop completion, the channel activates again if that channel has a minor loop channel link enabled and the link channel is itself.
-
bool enableHaltOnError
Enable (true) transfer halt on error. Any error causes the HALT bit to set. Subsequently, all service requests are ignored until the HALT bit is cleared.
-
bool enableRoundRobinArbitration
Enable (true) round robin channel arbitration method or fixed priority arbitration is used for channel selection
-
bool enableDebugMode
Enable(true) eDMA debug mode. When in debug mode, the eDMA stalls the start of a new channel. Executing channels are allowed to complete.
-
bool enableContinuousLinkMode
-
struct _edma_transfer_config
- #include <fsl_edma.h>
eDMA transfer configuration
This structure configures the source/destination transfer attribute.
Public Members
-
uint32_t srcAddr
Source data address.
-
uint32_t destAddr
Destination data address.
-
edma_transfer_size_t srcTransferSize
Source data transfer size.
-
edma_transfer_size_t destTransferSize
Destination data transfer size.
-
int16_t srcOffset
Sign-extended offset applied to the current source address to form the next-state value as each source read is completed.
-
int16_t destOffset
Sign-extended offset applied to the current destination address to form the next-state value as each destination write is completed.
-
uint32_t minorLoopBytes
Bytes to transfer in a minor loop
-
uint32_t majorLoopCounts
Major loop iteration count.
-
uint32_t srcAddr
-
struct _edma_channel_Preemption_config
- #include <fsl_edma.h>
eDMA channel priority configuration
Public Members
-
bool enableChannelPreemption
If true: a channel can be suspended by other channel with higher priority
-
bool enablePreemptAbility
If true: a channel can suspend other channel with low priority
-
uint8_t channelPriority
Channel priority
-
bool enableChannelPreemption
-
struct _edma_minor_offset_config
- #include <fsl_edma.h>
eDMA minor offset configuration
Public Members
-
bool enableSrcMinorOffset
Enable(true) or Disable(false) source minor loop offset.
-
bool enableDestMinorOffset
Enable(true) or Disable(false) destination minor loop offset.
-
uint32_t minorOffset
Offset for a minor loop mapping.
-
bool enableSrcMinorOffset
-
struct _edma_tcd
- #include <fsl_edma.h>
eDMA TCD.
This structure is same as TCD register which is described in reference manual, and is used to configure the scatter/gather feature as a next hardware TCD.
Public Members
- __IO uint32_t SADDR
SADDR register, used to save source address
- __IO uint16_t SOFF
SOFF register, save offset bytes every transfer
- __IO uint16_t ATTR
ATTR register, source/destination transfer size and modulo
- __IO uint32_t NBYTES
Nbytes register, minor loop length in bytes
- __IO uint32_t SLAST
SLAST register
- __IO uint32_t DADDR
DADDR register, used for destination address
- __IO uint16_t DOFF
DOFF register, used for destination offset
- __IO uint16_t CITER
CITER register, current minor loop numbers, for unfinished minor loop.
- __IO uint32_t DLAST_SGA
DLASTSGA register, next tcd address used in scatter-gather mode
- __IO uint16_t CSR
CSR register, for TCD control status
- __IO uint16_t BITER
BITER register, begin minor loop count.
-
struct _edma_handle
- #include <fsl_edma.h>
eDMA transfer handle structure
Public Members
-
edma_callback callback
Callback function for major count exhausted.
-
void *userData
Callback function parameter.
-
DMA_Type *base
eDMA peripheral base address.
-
edma_tcd_t *tcdPool
Pointer to memory stored TCDs.
-
uint8_t channel
eDMA channel number.
-
volatile int8_t header
The first TCD index. Should point to the next TCD to be loaded into the eDMA engine.
-
volatile int8_t tail
The last TCD index. Should point to the next TCD to be stored into the memory pool.
-
volatile int8_t tcdUsed
The number of used TCD slots. Should reflect the number of TCDs can be used/loaded in the memory.
-
volatile int8_t tcdSize
The total number of TCD slots in the queue.
-
uint8_t flags
The status of the current channel.
-
edma_callback callback
eLCDIF: Enhanced LCD Interface
-
void ELCDIF_RgbModeInit(LCDIF_Type *base, const elcdif_rgb_mode_config_t *config)
Initializes the eLCDIF to work in RGB mode (DOTCLK mode).
This function ungates the eLCDIF clock and configures the eLCDIF peripheral according to the configuration structure.
- Parameters:
base – eLCDIF peripheral base address.
config – Pointer to the configuration structure.
-
void ELCDIF_RgbModeGetDefaultConfig(elcdif_rgb_mode_config_t *config)
Gets the eLCDIF default configuration structure for RGB (DOTCLK) mode.
This function sets the configuration structure to default values. The default configuration is set to the following values.
config->panelWidth = 480U; config->panelHeight = 272U; config->hsw = 41; config->hfp = 4; config->hbp = 8; config->vsw = 10; config->vfp = 4; config->vbp = 2; config->polarityFlags = kELCDIF_VsyncActiveLow | kELCDIF_HsyncActiveLow | kELCDIF_DataEnableActiveLow | kELCDIF_DriveDataOnFallingClkEdge; config->bufferAddr = 0U; config->pixelFormat = kELCDIF_PixelFormatRGB888; config->dataBus = kELCDIF_DataBus24Bit;
- Parameters:
config – Pointer to the eLCDIF configuration structure.
-
void ELCDIF_Deinit(LCDIF_Type *base)
Deinitializes the eLCDIF peripheral.
- Parameters:
base – eLCDIF peripheral base address.
-
void ELCDIF_RgbModeSetPixelFormat(LCDIF_Type *base, elcdif_pixel_format_t pixelFormat)
Set the pixel format in RGB (DOTCLK) mode.
- Parameters:
base – eLCDIF peripheral base address.
pixelFormat – The pixel format.
-
static inline void ELCDIF_RgbModeStart(LCDIF_Type *base)
Start to display in RGB (DOTCLK) mode.
- Parameters:
base – eLCDIF peripheral base address.
-
void ELCDIF_RgbModeStop(LCDIF_Type *base)
Stop display in RGB (DOTCLK) mode and wait until finished.
- Parameters:
base – eLCDIF peripheral base address.
-
static inline void ELCDIF_SetNextBufferAddr(LCDIF_Type *base, uint32_t bufferAddr)
Set the next frame buffer address to display.
- Parameters:
base – eLCDIF peripheral base address.
bufferAddr – The frame buffer address to set.
-
void ELCDIF_Reset(LCDIF_Type *base)
Reset the eLCDIF peripheral.
- Parameters:
base – eLCDIF peripheral base address.
-
void ELCDIF_SetPixelComponentOrder(LCDIF_Type *base, elcdif_pixel_component_order_t order)
Set the order of the RGB components of each pixel in lines.
- Parameters:
base – eLCDIF peripheral base address.
order – The pixel component order
-
static inline uint32_t ELCDIF_GetCrcValue(const LCDIF_Type *base)
Get the CRC value of the frame sent out.
When a frame is sent complete (the interrupt kELCDIF_CurFrameDone assert), this function can be used to get the CRC value of the frame sent.
Note
The CRC value is dependent on the LCD_DATABUS_WIDTH.
- Parameters:
base – eLCDIF peripheral base address.
- Returns:
The CRC value.
-
static inline uint32_t ELCDIF_GetBusMasterErrorAddr(const LCDIF_Type *base)
Get the bus master error virtual address.
When bus master error occurs (the interrupt kELCDIF_BusMasterError assert), this function can get the virtual address at which the AXI master received an error response from the slave.
- Parameters:
base – eLCDIF peripheral base address.
- Returns:
The error virtual address.
-
static inline uint32_t ELCDIF_GetStatus(const LCDIF_Type *base)
Get the eLCDIF status.
The status flags are returned as a mask value, application could check the corresponding bit. Example:
uint32_t statusFlags; statusFlags = ELCDIF_GetStatus(LCDIF); if (kELCDIF_LFifoFull & statusFlags) { } if (kELCDIF_TxFifoEmpty & statusFlags) { }
- Parameters:
base – eLCDIF peripheral base address.
- Returns:
The mask value of status flags, it is OR’ed value of _elcdif_status_flags.
-
static inline uint32_t ELCDIF_GetLFifoCount(const LCDIF_Type *base)
Get current count in Latency buffer (LFIFO).
- Parameters:
base – eLCDIF peripheral base address.
- Returns:
The LFIFO current count
-
static inline void ELCDIF_EnableInterrupts(LCDIF_Type *base, uint32_t mask)
Enables eLCDIF interrupt requests.
- Parameters:
base – eLCDIF peripheral base address.
mask – interrupt source, OR’ed value of _elcdif_interrupt_enable.
-
static inline void ELCDIF_DisableInterrupts(LCDIF_Type *base, uint32_t mask)
Disables eLCDIF interrupt requests.
- Parameters:
base – eLCDIF peripheral base address.
mask – interrupt source, OR’ed value of _elcdif_interrupt_enable.
-
static inline uint32_t ELCDIF_GetInterruptStatus(const LCDIF_Type *base)
Get eLCDIF interrupt peding status.
- Parameters:
base – eLCDIF peripheral base address.
- Returns:
Interrupt pending status, OR’ed value of _elcdif_interrupt_flags.
-
static inline void ELCDIF_ClearInterruptStatus(LCDIF_Type *base, uint32_t mask)
Clear eLCDIF interrupt peding status.
- Parameters:
base – eLCDIF peripheral base address.
mask – of the flags to clear, OR’ed value of _elcdif_interrupt_flags.
-
static inline void ELCDIF_EnableLut(LCDIF_Type *base, bool enable)
Enable or disable the LUT.
- Parameters:
base – eLCDIF peripheral base address.
enable – True to enable, false to disable.
-
status_t ELCDIF_UpdateLut(LCDIF_Type *base, elcdif_lut_t lut, uint16_t startIndex, const uint32_t *lutData, uint16_t count)
Load the LUT value.
This function loads the LUT value to the specific LUT memory, user can specify the start entry index.
- Parameters:
base – eLCDIF peripheral base address.
lut – Which LUT to load.
startIndex – The start index of the LUT entry to update.
lutData – The LUT data to load.
count – Count of
lutData
.
- Return values:
kStatus_Success – Initialization success.
kStatus_InvalidArgument – Wrong argument.
-
FSL_ELCDIF_DRIVER_VERSION
eLCDIF driver version
-
enum _elcdif_polarity_flags
eLCDIF signal polarity flags
Values:
-
enumerator kELCDIF_VsyncActiveLow
VSYNC active low.
-
enumerator kELCDIF_HsyncActiveLow
HSYNC active low.
-
enumerator kELCDIF_DataEnableActiveLow
Data enable line active low.
-
enumerator kELCDIF_DriveDataOnFallingClkEdge
Drive data on falling clock edge, capture data on rising clock edge.
-
enumerator kELCDIF_VsyncActiveHigh
VSYNC active high.
-
enumerator kELCDIF_HsyncActiveHigh
HSYNC active high.
-
enumerator kELCDIF_DataEnableActiveHigh
Data enable line active high.
-
enumerator kELCDIF_DriveDataOnRisingClkEdge
Drive data on falling clock edge, capture data on rising clock edge.
-
enumerator kELCDIF_VsyncActiveLow
-
enum _elcdif_interrupt_enable
The eLCDIF interrupts to enable.
Values:
-
enumerator kELCDIF_BusMasterErrorInterruptEnable
Bus master error interrupt.
-
enumerator kELCDIF_TxFifoOverflowInterruptEnable
TXFIFO overflow interrupt.
-
enumerator kELCDIF_TxFifoUnderflowInterruptEnable
TXFIFO underflow interrupt.
-
enumerator kELCDIF_CurFrameDoneInterruptEnable
Interrupt when hardware enters vertical blanking state.
-
enumerator kELCDIF_VsyncEdgeInterruptEnable
Interrupt when hardware encounters VSYNC edge.
-
enumerator kELCDIF_BusMasterErrorInterruptEnable
-
enum _elcdif_interrupt_flags
The eLCDIF interrupt status flags.
Values:
-
enumerator kELCDIF_BusMasterError
Bus master error interrupt.
-
enumerator kELCDIF_TxFifoOverflow
TXFIFO overflow interrupt.
-
enumerator kELCDIF_TxFifoUnderflow
TXFIFO underflow interrupt.
-
enumerator kELCDIF_CurFrameDone
Interrupt when hardware enters vertical blanking state.
-
enumerator kELCDIF_VsyncEdge
Interrupt when hardware encounters VSYNC edge.
-
enumerator kELCDIF_BusMasterError
-
enum _elcdif_status_flags
eLCDIF status flags
Values:
-
enumerator kELCDIF_LFifoFull
LFIFO full.
-
enumerator kELCDIF_LFifoEmpty
LFIFO empty.
-
enumerator kELCDIF_TxFifoFull
TXFIFO full.
-
enumerator kELCDIF_TxFifoEmpty
TXFIFO empty.
-
enumerator kELCDIF_LFifoFull
-
enum _elcdif_pixel_format
The pixel format.
This enumerator should be defined together with the array s_pixelFormatReg. To support new pixel format, enhance this enumerator and s_pixelFormatReg.
Values:
-
enumerator kELCDIF_PixelFormatRAW8
RAW 8 bit, four data use 32 bits.
-
enumerator kELCDIF_PixelFormatRGB565
RGB565, two pixel use 32 bits.
-
enumerator kELCDIF_PixelFormatRGB666
RGB666 unpacked, one pixel uses 32 bits, high byte unused, upper 2 bits of other bytes unused.
-
enumerator kELCDIF_PixelFormatXRGB8888
XRGB8888 unpacked, one pixel uses 32 bits, high byte unused.
-
enumerator kELCDIF_PixelFormatRGB888
RGB888 packed, one pixel uses 24 bits.
-
enumerator kELCDIF_PixelFormatRAW8
-
enum _elcdif_lcd_data_bus
The LCD data bus type.
Values:
-
enumerator kELCDIF_DataBus8Bit
8-bit data bus.
-
enumerator kELCDIF_DataBus16Bit
16-bit data bus, support RGB565.
-
enumerator kELCDIF_DataBus18Bit
18-bit data bus, support RGB666.
-
enumerator kELCDIF_DataBus24Bit
24-bit data bus, support RGB888.
-
enumerator kELCDIF_DataBus8Bit
-
enum _elcdif_as_pixel_format
eLCDIF alpha surface pixel format.
Values:
-
enumerator kELCDIF_AsPixelFormatARGB8888
32-bit pixels with alpha.
-
enumerator kELCDIF_AsPixelFormatRGB888
32-bit pixels without alpha (unpacked 24-bit format)
-
enumerator kELCDIF_AsPixelFormatARGB1555
16-bit pixels with alpha.
-
enumerator kELCDIF_AsPixelFormatARGB4444
16-bit pixels with alpha.
-
enumerator kELCDIF_AsPixelFormatRGB555
16-bit pixels without alpha.
-
enumerator kELCDIF_AsPixelFormatRGB444
16-bit pixels without alpha.
-
enumerator kELCDIF_AsPixelFormatRGB565
16-bit pixels without alpha.
-
enumerator kELCDIF_AsPixelFormatARGB8888
-
enum _elcdif_alpha_mode
eLCDIF alpha mode during blending.
Values:
-
enumerator kELCDIF_AlphaEmbedded
The alpha surface pixel alpha value will be used for blend.
-
enumerator kELCDIF_AlphaOverride
The user defined alpha value will be used for blend directly.
-
enumerator kELCDIF_AlphaMultiply
The alpha surface pixel alpha value scaled the user defined alpha value will be used for blend, for example, pixel alpha set set to 200, user defined alpha set to 100, then the reault alpha is 200 * 100 / 255.
-
enumerator kELCDIF_AlphaRop
Raster operation.
-
enumerator kELCDIF_AlphaEmbedded
-
enum _elcdif_rop_mode
eLCDIF ROP mode during blending.
Explanation:
AS: Alpha surface
PS: Process surface
nAS: Alpha surface NOT value
nPS: Process surface NOT value
Values:
-
enumerator kELCDIF_RopMaskAs
AS AND PS.
-
enumerator kELCDIF_RopMaskNotAs
nAS AND PS.
-
enumerator kELCDIF_RopMaskAsNot
AS AND nPS.
-
enumerator kELCDIF_RopMergeAs
AS OR PS.
-
enumerator kELCDIF_RopMergeNotAs
nAS OR PS.
-
enumerator kELCDIF_RopMergeAsNot
AS OR nPS.
-
enumerator kELCDIF_RopNotCopyAs
nAS.
-
enumerator kELCDIF_RopNot
nPS.
-
enumerator kELCDIF_RopNotMaskAs
AS NAND PS.
-
enumerator kELCDIF_RopNotMergeAs
AS NOR PS.
-
enumerator kELCDIF_RopXorAs
AS XOR PS.
-
enumerator kELCDIF_RopNotXorAs
AS XNOR PS.
-
enum _elcdif_lut
eLCDIF LUT
The Lookup Table (LUT) is used to expand the 8 bits pixel to 24 bits pixel before output to external displayer.
There are two 256x24 bits LUT memory in LCDIF, the LSB of frame buffer address determins which memory to use.
Values:
-
enumerator kELCDIF_Lut0
LUT 0.
-
enumerator kELCDIF_Lut1
LUT 1.
-
enumerator kELCDIF_Lut0
-
enum _elcdif_pixel_component_order
eLCDIF pixel component order.
Values:
-
enumerator kELCDIF_PixelComponentOrderRGB
Input order RGB.
-
enumerator kELCDIF_PixelComponentOrderRBG
Input order RBG.
-
enumerator kELCDIF_PixelComponentOrderGBR
Input order GBR.
-
enumerator kELCDIF_PixelComponentOrderGRB
Input order GRB.
-
enumerator kELCDIF_PixelComponentOrderBRG
Input order BRG.
-
enumerator kELCDIF_PixelComponentOrderBGR
Input order BGR.
-
enumerator kELCDIF_PixelComponentOrderRGB
-
typedef enum _elcdif_pixel_format elcdif_pixel_format_t
The pixel format.
This enumerator should be defined together with the array s_pixelFormatReg. To support new pixel format, enhance this enumerator and s_pixelFormatReg.
-
typedef enum _elcdif_lcd_data_bus elcdif_lcd_data_bus_t
The LCD data bus type.
-
typedef struct _elcdif_pixel_format_reg elcdif_pixel_format_reg_t
The register value when using different pixel format.
These register bits control the pixel format:
CTRL[DATA_FORMAT_24_BIT]
CTRL[DATA_FORMAT_18_BIT]
CTRL[DATA_FORMAT_16_BIT]
CTRL[WORD_LENGTH]
CTRL1[BYTE_PACKING_FORMAT]
-
typedef struct _elcdif_rgb_mode_config elcdif_rgb_mode_config_t
eLCDIF configure structure for RGB mode (DOTCLK mode).
-
typedef enum _elcdif_as_pixel_format elcdif_as_pixel_format_t
eLCDIF alpha surface pixel format.
-
typedef struct _elcdif_as_buffer_config elcdif_as_buffer_config_t
eLCDIF alpha surface buffer configuration.
-
typedef enum _elcdif_alpha_mode elcdif_alpha_mode_t
eLCDIF alpha mode during blending.
-
typedef enum _elcdif_rop_mode elcdif_rop_mode_t
eLCDIF ROP mode during blending.
Explanation:
AS: Alpha surface
PS: Process surface
nAS: Alpha surface NOT value
nPS: Process surface NOT value
-
typedef struct _elcdif_as_blend_config elcdif_as_blend_config_t
eLCDIF alpha surface blending configuration.
-
typedef enum _elcdif_lut elcdif_lut_t
eLCDIF LUT
The Lookup Table (LUT) is used to expand the 8 bits pixel to 24 bits pixel before output to external displayer.
There are two 256x24 bits LUT memory in LCDIF, the LSB of frame buffer address determins which memory to use.
-
typedef enum _elcdif_pixel_component_order elcdif_pixel_component_order_t
eLCDIF pixel component order.
-
ELCDIF_CTRL1_IRQ_MASK
-
ELCDIF_CTRL1_IRQ_EN_MASK
-
ELCDIF_AS_CTRL_IRQ_MASK
-
ELCDIF_AS_CTRL_IRQ_EN_MASK
-
FSL_FEATURE_LCDIF_HAS_PXP_HANDSHAKE
-
ELCDIF_ADDR_CPU_2_IP(addr)
-
ELCDIF_LUT_ENTRY_NUM
-
struct _elcdif_pixel_format_reg
- #include <fsl_elcdif.h>
The register value when using different pixel format.
These register bits control the pixel format:
CTRL[DATA_FORMAT_24_BIT]
CTRL[DATA_FORMAT_18_BIT]
CTRL[DATA_FORMAT_16_BIT]
CTRL[WORD_LENGTH]
CTRL1[BYTE_PACKING_FORMAT]
Public Members
-
uint32_t regCtrl
Value of register CTRL.
-
uint32_t regCtrl1
Value of register CTRL1.
-
struct _elcdif_rgb_mode_config
- #include <fsl_elcdif.h>
eLCDIF configure structure for RGB mode (DOTCLK mode).
Public Members
-
uint16_t panelWidth
Display panel width, pixels per line.
-
uint16_t panelHeight
Display panel height, how many lines per panel.
-
uint8_t hsw
HSYNC pulse width.
-
uint8_t hfp
Horizontal front porch.
-
uint8_t hbp
Horizontal back porch.
-
uint8_t vsw
VSYNC pulse width.
-
uint8_t vfp
Vrtical front porch.
-
uint8_t vbp
Vertical back porch.
-
uint32_t polarityFlags
OR’ed value of _elcdif_polarity_flags, used to contol the signal polarity.
-
uint32_t bufferAddr
Frame buffer address.
-
elcdif_pixel_format_t pixelFormat
Pixel format.
-
elcdif_lcd_data_bus_t dataBus
LCD data bus.
-
uint16_t panelWidth
-
struct _elcdif_as_buffer_config
- #include <fsl_elcdif.h>
eLCDIF alpha surface buffer configuration.
Public Members
-
uint32_t bufferAddr
Buffer address.
-
elcdif_as_pixel_format_t pixelFormat
Pixel format.
-
uint32_t bufferAddr
-
struct _elcdif_as_blend_config
- #include <fsl_elcdif.h>
eLCDIF alpha surface blending configuration.
Public Members
-
uint8_t alpha
User defined alpha value, only used when alphaMode is kELCDIF_AlphaOverride or kELCDIF_AlphaRop.
-
bool invertAlpha
Set true to invert the alpha.
-
elcdif_alpha_mode_t alphaMode
Alpha mode.
-
elcdif_rop_mode_t ropMode
ROP mode, only valid when alphaMode is kELCDIF_AlphaRop.
-
uint8_t alpha
ENC: Quadrature Encoder/Decoder
-
void ENC_Init(ENC_Type *base, const enc_config_t *config)
Initialization for the ENC module.
This function is to make the initialization for the ENC module. It should be called firstly before any operation to the ENC with the operations like:
Enable the clock for ENC module.
Configure the ENC’s working attributes.
- Parameters:
base – ENC peripheral base address.
config – Pointer to configuration structure. See to “enc_config_t”.
-
void ENC_Deinit(ENC_Type *base)
De-initialization for the ENC module.
This function is to make the de-initialization for the ENC module. It could be called when ENC is no longer used with the operations like:
Disable the clock for ENC module.
- Parameters:
base – ENC peripheral base address.
-
void ENC_GetDefaultConfig(enc_config_t *config)
Get an available pre-defined settings for ENC’s configuration.
This function initializes the ENC configuration structure with an available settings, the default value are:
config->enableReverseDirection = false; config->decoderWorkMode = kENC_DecoderWorkAsNormalMode; config->HOMETriggerMode = kENC_HOMETriggerDisabled; config->INDEXTriggerMode = kENC_INDEXTriggerDisabled; config->enableTRIGGERClearPositionCounter = false; config->enableTRIGGERClearHoldPositionCounter = false; config->enableWatchdog = false; config->watchdogTimeoutValue = 0U; config->filterCount = 0U; config->filterSamplePeriod = 0U; config->positionMatchMode = kENC_POSMATCHOnPositionCounterEqualToComapreValue; config->positionCompareValue = 0xFFFFFFFFU; config->revolutionCountCondition = kENC_RevolutionCountOnINDEXPulse; config->enableModuloCountMode = false; config->positionModulusValue = 0U; config->positionInitialValue = 0U; config->prescalerValue = kENC_ClockDiv1; config->enablePeriodMeasurementFunction = true;
- Parameters:
config – Pointer to a variable of configuration structure. See to “enc_config_t”.
-
void ENC_DoSoftwareLoadInitialPositionValue(ENC_Type *base)
Load the initial position value to position counter.
This function is to transfer the initial position value (UINIT and LINIT) contents to position counter (UPOS and LPOS), so that to provide the consistent operation the position counter registers.
- Parameters:
base – ENC peripheral base address.
-
void ENC_SetSelfTestConfig(ENC_Type *base, const enc_self_test_config_t *config)
Enable and configure the self test function.
This function is to enable and configuration the self test function. It controls and sets the frequency of a quadrature signal generator. It provides a quadrature test signal to the inputs of the quadrature decoder module. It is a factory test feature; however, it may be useful to customers’ software development and testing.
- Parameters:
base – ENC peripheral base address.
config – Pointer to configuration structure. See to “enc_self_test_config_t”. Pass “NULL” to disable.
-
void ENC_EnableWatchdog(ENC_Type *base, bool enable)
Enable watchdog for ENC module.
- Parameters:
base – ENC peripheral base address
enable – Enables or disables the watchdog
-
void ENC_SetInitialPositionValue(ENC_Type *base, uint32_t value)
Set initial position value for ENC module.
- Parameters:
base – ENC peripheral base address
value – Positive initial value
-
uint32_t ENC_GetStatusFlags(ENC_Type *base)
Get the status flags.
- Parameters:
base – ENC peripheral base address.
- Returns:
Mask value of status flags. For available mask, see to “_enc_status_flags”.
-
void ENC_ClearStatusFlags(ENC_Type *base, uint32_t mask)
Clear the status flags.
- Parameters:
base – ENC peripheral base address.
mask – Mask value of status flags to be cleared. For available mask, see to “_enc_status_flags”.
-
static inline uint16_t ENC_GetSignalStatusFlags(ENC_Type *base)
Get the signals’ real-time status.
- Parameters:
base – ENC peripheral base address.
- Returns:
Mask value of signals’ real-time status. For available mask, see to “_enc_signal_status_flags”
-
void ENC_EnableInterrupts(ENC_Type *base, uint32_t mask)
Enable the interrupts.
- Parameters:
base – ENC peripheral base address.
mask – Mask value of interrupts to be enabled. For available mask, see to “_enc_interrupt_enable”.
-
void ENC_DisableInterrupts(ENC_Type *base, uint32_t mask)
Disable the interrupts.
- Parameters:
base – ENC peripheral base address.
mask – Mask value of interrupts to be disabled. For available mask, see to “_enc_interrupt_enable”.
-
uint32_t ENC_GetEnabledInterrupts(ENC_Type *base)
Get the enabled interrupts’ flags.
- Parameters:
base – ENC peripheral base address.
- Returns:
Mask value of enabled interrupts.
-
uint32_t ENC_GetPositionValue(ENC_Type *base)
Get the current position counter’s value.
- Parameters:
base – ENC peripheral base address.
- Returns:
Current position counter’s value.
-
uint32_t ENC_GetHoldPositionValue(ENC_Type *base)
Get the hold position counter’s value.
When any of the counter registers is read, the contents of each counter register is written to the corresponding hold register. Taking a snapshot of the counters’ values provides a consistent view of a system position and a velocity to be attained.
- Parameters:
base – ENC peripheral base address.
- Returns:
Hold position counter’s value.
-
static inline uint16_t ENC_GetPositionDifferenceValue(ENC_Type *base)
Get the position difference counter’s value.
- Parameters:
base – ENC peripheral base address.
- Returns:
The position difference counter’s value.
-
static inline uint16_t ENC_GetHoldPositionDifferenceValue(ENC_Type *base)
Get the hold position difference counter’s value.
When any of the counter registers is read, the contents of each counter register is written to the corresponding hold register. Taking a snapshot of the counters’ values provides a consistent view of a system position and a velocity to be attained.
- Parameters:
base – ENC peripheral base address.
- Returns:
Hold position difference counter’s value.
-
static inline uint16_t ENC_GetRevolutionValue(ENC_Type *base)
Get the position revolution counter’s value.
- Parameters:
base – ENC peripheral base address.
- Returns:
The position revolution counter’s value.
-
static inline uint16_t ENC_GetHoldRevolutionValue(ENC_Type *base)
Get the hold position revolution counter’s value.
When any of the counter registers is read, the contents of each counter register is written to the corresponding hold register. Taking a snapshot of the counters’ values provides a consistent view of a system position and a velocity to be attained.
- Parameters:
base – ENC peripheral base address.
- Returns:
Hold position revolution counter’s value.
-
static inline uint16_t ENC_GetLastEdgeTimeValue(ENC_Type *base)
Get the last edge time value.
- Parameters:
base – ENC peripheral base address.
- Returns:
The last edge time hold value.
-
static inline uint16_t ENC_GetHoldLastEdgeTimeValue(ENC_Type *base)
Get the last edge time hold value.
- Parameters:
base – ENC peripheral base address.
- Returns:
The last edge time hold value.
-
static inline uint16_t ENC_GetPositionDifferencePeriodValue(ENC_Type *base)
Get the position difference period value.
- Parameters:
base – ENC peripheral base address.
- Returns:
The position difference period hold value.
-
static inline uint16_t ENC_GetPositionDifferencePeriodBufferValue(ENC_Type *base)
Get the position difference period buffer value.
- Parameters:
base – ENC peripheral base address.
- Returns:
The position difference period hold value.
-
static inline uint16_t ENC_GetHoldPositionDifferencePeriodValue(ENC_Type *base)
Get the position difference period hold value.
- Parameters:
base – ENC peripheral base address.
- Returns:
The position difference period hold value.
-
enum _enc_interrupt_enable
Interrupt enable/disable mask.
Values:
-
enumerator kENC_HOMETransitionInterruptEnable
HOME interrupt enable.
-
enumerator kENC_INDEXPulseInterruptEnable
INDEX pulse interrupt enable.
-
enumerator kENC_WatchdogTimeoutInterruptEnable
Watchdog timeout interrupt enable.
-
enumerator kENC_PositionCompareInerruptEnable
Position compare interrupt enable.
-
enumerator kENC_PositionRollOverInterruptEnable
Roll-over interrupt enable.
-
enumerator kENC_PositionRollUnderInterruptEnable
Roll-under interrupt enable.
-
enumerator kENC_HOMETransitionInterruptEnable
-
enum _enc_status_flags
Status flag mask.
These flags indicate the counter’s events.
Values:
-
enumerator kENC_HOMETransitionFlag
HOME signal transition interrupt request.
-
enumerator kENC_INDEXPulseFlag
INDEX Pulse Interrupt Request.
-
enumerator kENC_WatchdogTimeoutFlag
Watchdog timeout interrupt request.
-
enumerator kENC_PositionCompareFlag
Position compare interrupt request.
-
enumerator kENC_PositionRollOverFlag
Roll-over interrupt request.
-
enumerator kENC_PositionRollUnderFlag
Roll-under interrupt request.
-
enumerator kENC_LastCountDirectionFlag
Last count was in the up direction, or the down direction.
-
enumerator kENC_HOMETransitionFlag
-
enum _enc_signal_status_flags
Signal status flag mask.
These flags indicate the counter’s signal.
Values:
-
enumerator kENC_RawHOMEStatusFlag
Raw HOME input.
-
enumerator kENC_RawINDEXStatusFlag
Raw INDEX input.
-
enumerator kENC_RawPHBStatusFlag
Raw PHASEB input.
-
enumerator kENC_RawPHAEXStatusFlag
Raw PHASEA input.
-
enumerator kENC_FilteredHOMEStatusFlag
The filtered version of HOME input.
-
enumerator kENC_FilteredINDEXStatusFlag
The filtered version of INDEX input.
-
enumerator kENC_FilteredPHBStatusFlag
The filtered version of PHASEB input.
-
enumerator kENC_FilteredPHAStatusFlag
The filtered version of PHASEA input.
-
enumerator kENC_RawHOMEStatusFlag
-
enum _enc_home_trigger_mode
Define HOME signal’s trigger mode.
The ENC would count the trigger from HOME signal line.
Values:
-
enumerator kENC_HOMETriggerDisabled
HOME signal’s trigger is disabled.
-
enumerator kENC_HOMETriggerOnRisingEdge
Use positive going edge-to-trigger initialization of position counters.
-
enumerator kENC_HOMETriggerOnFallingEdge
Use negative going edge-to-trigger initialization of position counters.
-
enumerator kENC_HOMETriggerDisabled
-
enum _enc_index_trigger_mode
Define INDEX signal’s trigger mode.
The ENC would count the trigger from INDEX signal line.
Values:
-
enumerator kENC_INDEXTriggerDisabled
INDEX signal’s trigger is disabled.
-
enumerator kENC_INDEXTriggerOnRisingEdge
Use positive going edge-to-trigger initialization of position counters.
-
enumerator kENC_INDEXTriggerOnFallingEdge
Use negative going edge-to-trigger initialization of position counters.
-
enumerator kENC_INDEXTriggerDisabled
-
enum _enc_decoder_work_mode
Define type for decoder work mode.
The normal work mode uses the standard quadrature decoder with PHASEA and PHASEB. When in signal phase count mode, a positive transition of the PHASEA input generates a count signal while the PHASEB input and the reverse direction control the counter direction. If the reverse direction is not enabled, PHASEB = 0 means counting up and PHASEB = 1 means counting down. Otherwise, the direction is reversed.
Values:
-
enumerator kENC_DecoderWorkAsNormalMode
Use standard quadrature decoder with PHASEA and PHASEB.
-
enumerator kENC_DecoderWorkAsSignalPhaseCountMode
PHASEA input generates a count signal while PHASEB input control the direction.
-
enumerator kENC_DecoderWorkAsNormalMode
-
enum _enc_position_match_mode
Define type for the condition of POSMATCH pulses.
Values:
-
enumerator kENC_POSMATCHOnPositionCounterEqualToComapreValue
POSMATCH pulses when a match occurs between the position counters (POS) and the compare value (COMP).
-
enumerator kENC_POSMATCHOnReadingAnyPositionCounter
POSMATCH pulses when any position counter register is read.
-
enumerator kENC_POSMATCHOnPositionCounterEqualToComapreValue
-
enum _enc_revolution_count_condition
Define type for determining how the revolution counter (REV) is incremented/decremented.
Values:
-
enumerator kENC_RevolutionCountOnINDEXPulse
Use INDEX pulse to increment/decrement revolution counter.
-
enumerator kENC_RevolutionCountOnRollOverModulus
Use modulus counting roll-over/under to increment/decrement revolution counter.
-
enumerator kENC_RevolutionCountOnINDEXPulse
-
enum _enc_self_test_direction
Define type for direction of self test generated signal.
Values:
-
enumerator kENC_SelfTestDirectionPositive
Self test generates the signal in positive direction.
-
enumerator kENC_SelfTestDirectionNegative
Self test generates the signal in negative direction.
-
enumerator kENC_SelfTestDirectionPositive
-
enum _enc_prescaler
Define prescaler value for clock in CTRL3.
The clock is prescaled by a value of 2^PRSC which means that the prescaler logic can divide the clock by a minimum of 1 and a maximum of 32,768.
Values:
-
enumerator kENC_ClockDiv1
-
enumerator kENC_ClockDiv2
-
enumerator kENC_ClockDiv4
-
enumerator kENC_ClockDiv8
-
enumerator kENC_ClockDiv16
-
enumerator kENC_ClockDiv32
-
enumerator kENC_ClockDiv64
-
enumerator kENC_ClockDiv128
-
enumerator kENC_ClockDiv256
-
enumerator kENC_ClockDiv512
-
enumerator kENC_ClockDiv1024
-
enumerator kENC_ClockDiv2048
-
enumerator kENC_ClockDiv4096
-
enumerator kENC_ClockDiv8192
-
enumerator kENC_ClockDiv16384
-
enumerator kENC_ClockDiv32768
-
enumerator kENC_ClockDiv1
-
enum _enc_filter_prescaler
Define input filter prescaler value.
The input filter prescaler value is to prescale the IPBus clock. (Frequency of FILT clock) = (Frequency of IPBus clock) / 2^FILT_PRSC.
Values:
-
enumerator kENC_FilterPrescalerDiv1
Input filter prescaler is 1.
-
enumerator kENC_FilterPrescalerDiv2
Input filter prescaler is 2.
-
enumerator kENC_FilterPrescalerDiv4
Input filter prescaler is 4.
-
enumerator kENC_FilterPrescalerDiv8
Input filter prescaler is 8.
-
enumerator kENC_FilterPrescalerDiv16
Input filter prescaler is 16.
-
enumerator kENC_FilterPrescalerDiv32
Input filter prescaler is 32.
-
enumerator kENC_FilterPrescalerDiv64
Input filter prescaler is 64.
-
enumerator kENC_FilterPrescalerDiv128
Input filter prescaler is 128.
-
enumerator kENC_FilterPrescalerDiv1
-
typedef enum _enc_home_trigger_mode enc_home_trigger_mode_t
Define HOME signal’s trigger mode.
The ENC would count the trigger from HOME signal line.
-
typedef enum _enc_index_trigger_mode enc_index_trigger_mode_t
Define INDEX signal’s trigger mode.
The ENC would count the trigger from INDEX signal line.
-
typedef enum _enc_decoder_work_mode enc_decoder_work_mode_t
Define type for decoder work mode.
The normal work mode uses the standard quadrature decoder with PHASEA and PHASEB. When in signal phase count mode, a positive transition of the PHASEA input generates a count signal while the PHASEB input and the reverse direction control the counter direction. If the reverse direction is not enabled, PHASEB = 0 means counting up and PHASEB = 1 means counting down. Otherwise, the direction is reversed.
-
typedef enum _enc_position_match_mode enc_position_match_mode_t
Define type for the condition of POSMATCH pulses.
-
typedef enum _enc_revolution_count_condition enc_revolution_count_condition_t
Define type for determining how the revolution counter (REV) is incremented/decremented.
-
typedef enum _enc_self_test_direction enc_self_test_direction_t
Define type for direction of self test generated signal.
-
typedef enum _enc_prescaler enc_prescaler_t
Define prescaler value for clock in CTRL3.
The clock is prescaled by a value of 2^PRSC which means that the prescaler logic can divide the clock by a minimum of 1 and a maximum of 32,768.
-
typedef enum _enc_filter_prescaler enc_filter_prescaler_t
Define input filter prescaler value.
The input filter prescaler value is to prescale the IPBus clock. (Frequency of FILT clock) = (Frequency of IPBus clock) / 2^FILT_PRSC.
-
typedef struct _enc_config enc_config_t
Define user configuration structure for ENC module.
-
typedef struct _enc_self_test_config enc_self_test_config_t
Define configuration structure for self test module.
The self test module provides a quadrature test signal to the inputs of the quadrature decoder module. This is a factory test feature. It is also useful to customers’ software development and testing.
-
FSL_ENC_DRIVER_VERSION
-
struct _enc_config
- #include <fsl_enc.h>
Define user configuration structure for ENC module.
Public Members
-
bool enableReverseDirection
Enable reverse direction counting.
-
enc_decoder_work_mode_t decoderWorkMode
Enable signal phase count mode.
-
enc_home_trigger_mode_t HOMETriggerMode
Enable HOME to initialize position counters.
-
enc_index_trigger_mode_t INDEXTriggerMode
Enable INDEX to initialize position counters.
-
bool enableTRIGGERClearPositionCounter
Clear POSD, REV, UPOS and LPOS on rising edge of TRIGGER, or not.
-
bool enableTRIGGERClearHoldPositionCounter
Enable update of hold registers on rising edge of TRIGGER, or not.
-
bool enableWatchdog
Enable the watchdog to detect if the target is moving or not.
-
uint16_t watchdogTimeoutValue
Watchdog timeout count value. It stores the timeout count for the quadrature decoder module watchdog timer. This field is only available when “enableWatchdog” = true. The available value is a 16-bit unsigned number.
-
enc_filter_prescaler_t filterPrescaler
Input filter prescaler.
-
uint16_t filterCount
Input Filter Sample Count. This value should be chosen to reduce the probability of noisy samples causing an incorrect transition to be recognized. The value represent the number of consecutive samples that must agree prior to the input filter accepting an input transition. A value of 0x0 represents 3 samples. A value of 0x7 represents 10 samples. The Available range is 0 - 7.
-
uint16_t filterSamplePeriod
Input Filter Sample Period. This value should be set such that the sampling period is larger than the period of the expected noise. This value represents the sampling period (in IPBus clock cycles) of the decoder input signals. The available range is 0 - 255.
-
enc_position_match_mode_t positionMatchMode
The condition of POSMATCH pulses.
-
uint32_t positionCompareValue
Position compare value. The available value is a 32-bit number.
-
enc_revolution_count_condition_t revolutionCountCondition
Revolution Counter Modulus Enable.
-
bool enableModuloCountMode
Enable Modulo Counting.
-
uint32_t positionModulusValue
Position modulus value. This value would be available only when “enableModuloCountMode” = true. The available value is a 32-bit number.
-
uint32_t positionInitialValue
Position initial value. The available value is a 32-bit number.
-
bool enablePeriodMeasurementFunction
Enable period measurement function.
-
enc_prescaler_t prescalerValue
The value of prescaler.
-
bool enableReverseDirection
-
struct _enc_self_test_config
- #include <fsl_enc.h>
Define configuration structure for self test module.
The self test module provides a quadrature test signal to the inputs of the quadrature decoder module. This is a factory test feature. It is also useful to customers’ software development and testing.
Public Members
-
enc_self_test_direction_t signalDirection
Direction of self test generated signal.
-
uint16_t signalCount
Hold the number of quadrature advances to generate. The available range is 0 - 255.
-
uint16_t signalPeriod
Hold the period of quadrature phase in IPBus clock cycles. The available range is 0 - 31.
-
enc_self_test_direction_t signalDirection
ENET: Ethernet MAC Driver
-
void ENET_GetDefaultConfig(enet_config_t *config)
Gets the ENET default configuration structure.
The purpose of this API is to get the default ENET MAC controller configure structure for ENET_Init(). User may use the initialized structure unchanged in ENET_Init(), or modify some fields of the structure before calling ENET_Init(). Example:
enet_config_t config; ENET_GetDefaultConfig(&config);
- Parameters:
config – The ENET mac controller configuration structure pointer.
-
status_t ENET_Up(ENET_Type *base, enet_handle_t *handle, const enet_config_t *config, const enet_buffer_config_t *bufferConfig, uint8_t *macAddr, uint32_t srcClock_Hz)
Initializes the ENET module.
This function initializes the module with the ENET configuration.
Note
ENET has two buffer descriptors legacy buffer descriptors and enhanced IEEE 1588 buffer descriptors. The legacy descriptor is used by default. To use the IEEE 1588 feature, use the enhanced IEEE 1588 buffer descriptor by defining “ENET_ENHANCEDBUFFERDESCRIPTOR_MODE” and calling ENET_Ptp1588Configure() to configure the 1588 feature and related buffers after calling ENET_Up().
- Parameters:
base – ENET peripheral base address.
handle – ENET handler pointer.
config – ENET mac configuration structure pointer. The “enet_config_t” type mac configuration return from ENET_GetDefaultConfig can be used directly. It is also possible to verify the Mac configuration using other methods.
bufferConfig – ENET buffer configuration structure pointer. The buffer configuration should be prepared for ENET Initialization. It is the start address of “ringNum” enet_buffer_config structures. To support added multi-ring features in some soc and compatible with the previous enet driver version. For single ring supported, this bufferConfig is a buffer configure structure pointer, for multi-ring supported and used case, this bufferConfig pointer should be a buffer configure structure array pointer.
macAddr – ENET mac address of Ethernet device. This MAC address should be provided.
srcClock_Hz – The internal module clock source for MII clock.
- Return values:
kStatus_Success – Succeed to initialize the ethernet driver.
kStatus_ENET_InitMemoryFail – Init fails since buffer memory is not enough.
-
status_t ENET_Init(ENET_Type *base, enet_handle_t *handle, const enet_config_t *config, const enet_buffer_config_t *bufferConfig, uint8_t *macAddr, uint32_t srcClock_Hz)
Initializes the ENET module.
This function ungates the module clock and initializes it with the ENET configuration.
Note
ENET has two buffer descriptors legacy buffer descriptors and enhanced IEEE 1588 buffer descriptors. The legacy descriptor is used by default. To use the IEEE 1588 feature, use the enhanced IEEE 1588 buffer descriptor by defining “ENET_ENHANCEDBUFFERDESCRIPTOR_MODE” and calling ENET_Ptp1588Configure() to configure the 1588 feature and related buffers after calling ENET_Init().
- Parameters:
base – ENET peripheral base address.
handle – ENET handler pointer.
config – ENET mac configuration structure pointer. The “enet_config_t” type mac configuration return from ENET_GetDefaultConfig can be used directly. It is also possible to verify the Mac configuration using other methods.
bufferConfig – ENET buffer configuration structure pointer. The buffer configuration should be prepared for ENET Initialization. It is the start address of “ringNum” enet_buffer_config structures. To support added multi-ring features in some soc and compatible with the previous enet driver version. For single ring supported, this bufferConfig is a buffer configure structure pointer, for multi-ring supported and used case, this bufferConfig pointer should be a buffer configure structure array pointer.
macAddr – ENET mac address of Ethernet device. This MAC address should be provided.
srcClock_Hz – The internal module clock source for MII clock.
- Return values:
kStatus_Success – Succeed to initialize the ethernet driver.
kStatus_ENET_InitMemoryFail – Init fails since buffer memory is not enough.
-
void ENET_Down(ENET_Type *base)
Stops the ENET module.
This function disables the ENET module.
- Parameters:
base – ENET peripheral base address.
-
void ENET_Deinit(ENET_Type *base)
Deinitializes the ENET module.
This function gates the module clock, clears ENET interrupts, and disables the ENET module.
- Parameters:
base – ENET peripheral base address.
-
static inline void ENET_Reset(ENET_Type *base)
Resets the ENET module.
This function restores the ENET module to reset state. Note that this function sets all registers to reset state. As a result, the ENET module can’t work after calling this function.
- Parameters:
base – ENET peripheral base address.
-
void ENET_SetMII(ENET_Type *base, enet_mii_speed_t speed, enet_mii_duplex_t duplex)
Sets the ENET MII speed and duplex.
This API is provided to dynamically change the speed and dulpex for MAC.
- Parameters:
base – ENET peripheral base address.
speed – The speed of the RMII mode.
duplex – The duplex of the RMII mode.
-
void ENET_SetSMI(ENET_Type *base, uint32_t srcClock_Hz, bool isPreambleDisabled)
Sets the ENET SMI(serial management interface)- MII management interface.
- Parameters:
base – ENET peripheral base address.
srcClock_Hz – This is the ENET module clock frequency. See clock distribution.
isPreambleDisabled – The preamble disable flag.
true Enables the preamble.
false Disables the preamble.
-
static inline bool ENET_GetSMI(ENET_Type *base)
Gets the ENET SMI- MII management interface configuration.
This API is used to get the SMI configuration to check whether the MII management interface has been set.
- Parameters:
base – ENET peripheral base address.
- Returns:
The SMI setup status true or false.
-
static inline uint32_t ENET_ReadSMIData(ENET_Type *base)
Reads data from the PHY register through an SMI interface.
- Parameters:
base – ENET peripheral base address.
- Returns:
The data read from PHY
-
static inline void ENET_StartSMIWrite(ENET_Type *base, uint8_t phyAddr, uint8_t regAddr, enet_mii_write_t operation, uint16_t data)
Sends the MDIO IEEE802.3 Clause 22 format write command.
After calling this function, need to check whether the transmission is over then do next MDIO operation. For ease of use, encapsulated ENET_MDIOWrite() can be called. For customized requirements, implement with combining separated APIs.
- Parameters:
base – ENET peripheral base address.
phyAddr – The PHY address. Range from 0 ~ 31.
regAddr – The PHY register address. Range from 0 ~ 31.
operation – The write operation.
data – The data written to PHY.
-
static inline void ENET_StartSMIRead(ENET_Type *base, uint8_t phyAddr, uint8_t regAddr, enet_mii_read_t operation)
Sends the MDIO IEEE802.3 Clause 22 format read command.
After calling this function, need to check whether the transmission is over then do next MDIO operation. For ease of use, encapsulated ENET_MDIORead() can be called. For customized requirements, implement with combining separated APIs.
- Parameters:
base – ENET peripheral base address.
phyAddr – The PHY address. Range from 0 ~ 31.
regAddr – The PHY register address. Range from 0 ~ 31.
operation – The read operation.
-
status_t ENET_MDIOWrite(ENET_Type *base, uint8_t phyAddr, uint8_t regAddr, uint16_t data)
MDIO write with IEEE802.3 Clause 22 format.
- Parameters:
base – ENET peripheral base address.
phyAddr – The PHY address. Range from 0 ~ 31.
regAddr – The PHY register. Range from 0 ~ 31.
data – The data written to PHY.
- Returns:
kStatus_Success MDIO access succeeds.
- Returns:
kStatus_Timeout MDIO access timeout.
-
status_t ENET_MDIORead(ENET_Type *base, uint8_t phyAddr, uint8_t regAddr, uint16_t *pData)
MDIO read with IEEE802.3 Clause 22 format.
- Parameters:
base – ENET peripheral base address.
phyAddr – The PHY address. Range from 0 ~ 31.
regAddr – The PHY register. Range from 0 ~ 31.
pData – The data read from PHY.
- Returns:
kStatus_Success MDIO access succeeds.
- Returns:
kStatus_Timeout MDIO access timeout.
-
static inline void ENET_StartExtC45SMIWriteReg(ENET_Type *base, uint8_t portAddr, uint8_t devAddr, uint16_t regAddr)
Sends the MDIO IEEE802.3 Clause 45 format write register command.
After calling this function, need to check whether the transmission is over then do next MDIO operation. For ease of use, encapsulated ENET_MDIOC45Write()/ENET_MDIOC45Read() can be called. For customized requirements, implement with combining separated APIs.
- Parameters:
base – ENET peripheral base address.
portAddr – The MDIO port address(PHY address).
devAddr – The device address.
regAddr – The PHY register address.
-
static inline void ENET_StartExtC45SMIWriteData(ENET_Type *base, uint8_t portAddr, uint8_t devAddr, uint16_t data)
Sends the MDIO IEEE802.3 Clause 45 format write data command.
After calling this function, need to check whether the transmission is over then do next MDIO operation. For ease of use, encapsulated ENET_MDIOC45Write() can be called. For customized requirements, implement with combining separated APIs.
- Parameters:
base – ENET peripheral base address.
portAddr – The MDIO port address(PHY address).
devAddr – The device address.
data – The data written to PHY.
-
static inline void ENET_StartExtC45SMIReadData(ENET_Type *base, uint8_t portAddr, uint8_t devAddr)
Sends the MDIO IEEE802.3 Clause 45 format read data command.
After calling this function, need to check whether the transmission is over then do next MDIO operation. For ease of use, encapsulated ENET_MDIOC45Read() can be called. For customized requirements, implement with combining separated APIs.
- Parameters:
base – ENET peripheral base address.
portAddr – The MDIO port address(PHY address).
devAddr – The device address.
-
status_t ENET_MDIOC45Write(ENET_Type *base, uint8_t portAddr, uint8_t devAddr, uint16_t regAddr, uint16_t data)
MDIO write with IEEE802.3 Clause 45 format.
- Parameters:
base – ENET peripheral base address.
portAddr – The MDIO port address(PHY address).
devAddr – The device address.
regAddr – The PHY register address.
data – The data written to PHY.
- Returns:
kStatus_Success MDIO access succeeds.
- Returns:
kStatus_Timeout MDIO access timeout.
-
status_t ENET_MDIOC45Read(ENET_Type *base, uint8_t portAddr, uint8_t devAddr, uint16_t regAddr, uint16_t *pData)
MDIO read with IEEE802.3 Clause 45 format.
- Parameters:
base – ENET peripheral base address.
portAddr – The MDIO port address(PHY address).
devAddr – The device address.
regAddr – The PHY register address.
pData – The data read from PHY.
- Returns:
kStatus_Success MDIO access succeeds.
- Returns:
kStatus_Timeout MDIO access timeout.
-
static inline void ENET_SetRGMIIClockDelay(ENET_Type *base, bool txEnabled, bool rxEnabled)
Control the usage of the delayed tx/rx RGMII clock.
- Parameters:
base – ENET peripheral base address.
txEnabled – Enable or disable to generate the delayed version of RGMII_TXC.
rxEnabled – Enable or disable to use the delayed version of RGMII_RXC.
-
void ENET_SetMacAddr(ENET_Type *base, uint8_t *macAddr)
Sets the ENET module Mac address.
- Parameters:
base – ENET peripheral base address.
macAddr – The six-byte Mac address pointer. The pointer is allocated by application and input into the API.
-
void ENET_GetMacAddr(ENET_Type *base, uint8_t *macAddr)
Gets the ENET module Mac address.
- Parameters:
base – ENET peripheral base address.
macAddr – The six-byte Mac address pointer. The pointer is allocated by application and input into the API.
-
void ENET_AddMulticastGroup(ENET_Type *base, uint8_t *address)
Adds the ENET device to a multicast group.
- Parameters:
base – ENET peripheral base address.
address – The six-byte multicast group address which is provided by application.
-
void ENET_LeaveMulticastGroup(ENET_Type *base, uint8_t *address)
Moves the ENET device from a multicast group.
- Parameters:
base – ENET peripheral base address.
address – The six-byte multicast group address which is provided by application.
-
static inline void ENET_ActiveRead(ENET_Type *base)
Activates frame reception for multiple rings.
This function is to active the enet read process.
Note
This must be called after the MAC configuration and state are ready. It must be called after the ENET_Init(). This should be called when the frame reception is required.
- Parameters:
base – ENET peripheral base address.
-
static inline void ENET_EnableSleepMode(ENET_Type *base, bool enable)
Enables/disables the MAC to enter sleep mode. This function is used to set the MAC enter sleep mode. When entering sleep mode, the magic frame wakeup interrupt should be enabled to wake up MAC from the sleep mode and reset it to normal mode.
- Parameters:
base – ENET peripheral base address.
enable – True enable sleep mode, false disable sleep mode.
-
static inline void ENET_GetAccelFunction(ENET_Type *base, uint32_t *txAccelOption, uint32_t *rxAccelOption)
Gets ENET transmit and receive accelerator functions from MAC controller.
- Parameters:
base – ENET peripheral base address.
txAccelOption – The transmit accelerator option. The “enet_tx_accelerator_t” is recommended to be used to as the mask to get the exact the accelerator option.
rxAccelOption – The receive accelerator option. The “enet_rx_accelerator_t” is recommended to be used to as the mask to get the exact the accelerator option.
-
static inline void ENET_EnableInterrupts(ENET_Type *base, uint32_t mask)
Enables the ENET interrupt.
This function enables the ENET interrupt according to the provided mask. The mask is a logical OR of enumeration members. See enet_interrupt_enable_t. For example, to enable the TX frame interrupt and RX frame interrupt, do the following.
ENET_EnableInterrupts(ENET, kENET_TxFrameInterrupt | kENET_RxFrameInterrupt);
- Parameters:
base – ENET peripheral base address.
mask – ENET interrupts to enable. This is a logical OR of the enumeration enet_interrupt_enable_t.
-
static inline void ENET_DisableInterrupts(ENET_Type *base, uint32_t mask)
Disables the ENET interrupt.
This function disables the ENET interrupts according to the provided mask. The mask is a logical OR of enumeration members. See enet_interrupt_enable_t. For example, to disable the TX frame interrupt and RX frame interrupt, do the following.
ENET_DisableInterrupts(ENET, kENET_TxFrameInterrupt | kENET_RxFrameInterrupt);
- Parameters:
base – ENET peripheral base address.
mask – ENET interrupts to disable. This is a logical OR of the enumeration enet_interrupt_enable_t.
-
static inline uint32_t ENET_GetInterruptStatus(ENET_Type *base)
Gets the ENET interrupt status flag.
- Parameters:
base – ENET peripheral base address.
- Returns:
The event status of the interrupt source. This is the logical OR of members of the enumeration enet_interrupt_enable_t.
-
static inline void ENET_ClearInterruptStatus(ENET_Type *base, uint32_t mask)
Clears the ENET interrupt events status flag.
This function clears enabled ENET interrupts according to the provided mask. The mask is a logical OR of enumeration members. See the enet_interrupt_enable_t. For example, to clear the TX frame interrupt and RX frame interrupt, do the following.
ENET_ClearInterruptStatus(ENET, kENET_TxFrameInterrupt | kENET_RxFrameInterrupt);
- Parameters:
base – ENET peripheral base address.
mask – ENET interrupt source to be cleared. This is the logical OR of members of the enumeration enet_interrupt_enable_t.
-
void ENET_SetRxISRHandler(ENET_Type *base, enet_isr_t ISRHandler)
Set the second level Rx IRQ handler.
- Parameters:
base – ENET peripheral base address.
ISRHandler – The handler to install.
-
void ENET_SetTxISRHandler(ENET_Type *base, enet_isr_t ISRHandler)
Set the second level Tx IRQ handler.
- Parameters:
base – ENET peripheral base address.
ISRHandler – The handler to install.
-
void ENET_SetErrISRHandler(ENET_Type *base, enet_isr_t ISRHandler)
Set the second level Err IRQ handler.
- Parameters:
base – ENET peripheral base address.
ISRHandler – The handler to install.
-
void ENET_GetRxErrBeforeReadFrame(enet_handle_t *handle, enet_data_error_stats_t *eErrorStatic, uint8_t ringId)
Gets the error statistics of a received frame for ENET specified ring.
This API must be called after the ENET_GetRxFrameSize and before the ENET_ReadFrame(). If the ENET_GetRxFrameSize returns kStatus_ENET_RxFrameError, the ENET_GetRxErrBeforeReadFrame can be used to get the exact error statistics. This is an example.
status = ENET_GetRxFrameSize(&g_handle, &length, 0); if (status == kStatus_ENET_RxFrameError) { Comments: Get the error information of the received frame. ENET_GetRxErrBeforeReadFrame(&g_handle, &eErrStatic, 0); Comments: update the receive buffer. ENET_ReadFrame(EXAMPLE_ENET, &g_handle, NULL, 0); }
- Parameters:
handle – The ENET handler structure pointer. This is the same handler pointer used in the ENET_Init.
eErrorStatic – The error statistics structure pointer.
ringId – The ring index, range from 0 ~ (FSL_FEATURE_ENET_INSTANCE_QUEUEn(x) - 1).
-
void ENET_EnableStatistics(ENET_Type *base, bool enable)
Enables/disables collection of transfer statistics.
Note that this function does not reset any of the already collected data, use the function ENET_ResetStatistics to clear the transfer statistics if needed.
- Parameters:
base – ENET peripheral base address.
enable – True enable statistics collection, false disable statistics collection.
-
void ENET_GetStatistics(ENET_Type *base, enet_transfer_stats_t *statistics)
Gets transfer statistics.
Copies the actual value of hardware counters into the provided structure. Calling this function does not reset the counters in hardware.
- Parameters:
base – ENET peripheral base address.
statistics – The statistics structure pointer.
-
void ENET_ResetStatistics(ENET_Type *base)
Resets transfer statistics.
Sets the value of hardware transfer counters to zero.
- Parameters:
base – ENET peripheral base address.
-
status_t ENET_GetRxFrameSize(enet_handle_t *handle, uint32_t *length, uint8_t ringId)
Gets the size of the read frame for specified ring.
This function gets a received frame size from the ENET buffer descriptors.
Note
The FCS of the frame is automatically removed by MAC and the size is the length without the FCS. After calling ENET_GetRxFrameSize, ENET_ReadFrame() should be called to receive frame and update the BD if the result is not “kStatus_ENET_RxFrameEmpty”.
- Parameters:
handle – The ENET handler structure. This is the same handler pointer used in the ENET_Init.
length – The length of the valid frame received.
ringId – The ring index or ring number.
- Return values:
kStatus_ENET_RxFrameEmpty – No frame received. Should not call ENET_ReadFrame to read frame.
kStatus_ENET_RxFrameError – Data error happens. ENET_ReadFrame should be called with NULL data and NULL length to update the receive buffers.
kStatus_Success – Receive a frame Successfully then the ENET_ReadFrame should be called with the right data buffer and the captured data length input.
-
status_t ENET_ReadFrame(ENET_Type *base, enet_handle_t *handle, uint8_t *data, uint32_t length, uint8_t ringId, uint32_t *ts)
Reads a frame from the ENET device. This function reads a frame (both the data and the length) from the ENET buffer descriptors. User can get timestamp through ts pointer if the ts is not NULL.
Note
It doesn’t store the timestamp in the receive timestamp queue. The ENET_GetRxFrameSize should be used to get the size of the prepared data buffer. This API uses memcpy to copy data from DMA buffer to application buffer, 4 bytes aligned data buffer in 32 bits platforms provided by user may let compiler use optimization instruction to reduce time consumption. This is an example:
uint32_t length; enet_handle_t g_handle; Comments: Get the received frame size firstly. status = ENET_GetRxFrameSize(&g_handle, &length, 0); if (length != 0) { Comments: Allocate memory here with the size of "length" uint8_t *data = memory allocate interface; if (!data) { ENET_ReadFrame(ENET, &g_handle, NULL, 0, 0, NULL); Comments: Add the console warning log. } else { status = ENET_ReadFrame(ENET, &g_handle, data, length, 0, NULL); Comments: Call stack input API to deliver the data to stack } } else if (status == kStatus_ENET_RxFrameError) { Comments: Update the received buffer when a error frame is received. ENET_ReadFrame(ENET, &g_handle, NULL, 0, 0, NULL); }
- Parameters:
base – ENET peripheral base address.
handle – The ENET handler structure. This is the same handler pointer used in the ENET_Init.
data – The data buffer provided by user to store the frame which memory size should be at least “length”.
length – The size of the data buffer which is still the length of the received frame.
ringId – The ring index or ring number.
ts – The timestamp address to store received timestamp.
- Returns:
The execute status, successful or failure.
-
status_t ENET_SendFrame(ENET_Type *base, enet_handle_t *handle, const uint8_t *data, uint32_t length, uint8_t ringId, bool tsFlag, void *context)
Transmits an ENET frame for specified ring.
Note
The CRC is automatically appended to the data. Input the data to send without the CRC. This API uses memcpy to copy data from DMA buffer to application buffer, 4 bytes aligned data buffer in 32 bits platforms provided by user may let compiler use optimization instruction to reduce time consumption.
- Parameters:
base – ENET peripheral base address.
handle – The ENET handler pointer. This is the same handler pointer used in the ENET_Init.
data – The data buffer provided by user to send.
length – The length of the data to send.
ringId – The ring index or ring number.
tsFlag – Timestamp enable flag.
context – Used by user to handle some events after transmit over.
- Return values:
kStatus_Success – Send frame succeed.
kStatus_ENET_TxFrameBusy – Transmit buffer descriptor is busy under transmission. The transmit busy happens when the data send rate is over the MAC capacity. The waiting mechanism is recommended to be added after each call return with kStatus_ENET_TxFrameBusy.
-
status_t ENET_SetTxReclaim(enet_handle_t *handle, bool isEnable, uint8_t ringId)
Enable or disable tx descriptors reclaim mechanism.
Note
This function must be called when no pending send frame action. Set enable if you want to reclaim context or timestamp in interrupt.
- Parameters:
handle – The ENET handler pointer. This is the same handler pointer used in the ENET_Init.
isEnable – Enable or disable flag.
ringId – The ring index or ring number.
- Return values:
kStatus_Success – Succeed to enable/disable Tx reclaim.
kStatus_Fail – Fail to enable/disable Tx reclaim.
-
void ENET_ReclaimTxDescriptor(ENET_Type *base, enet_handle_t *handle, uint8_t ringId)
Reclaim tx descriptors. This function is used to update the tx descriptor status and store the tx timestamp when the 1588 feature is enabled. This is called by the transmit interupt IRQ handler after the complete of a frame transmission.
- Parameters:
base – ENET peripheral base address.
handle – The ENET handler pointer. This is the same handler pointer used in the ENET_Init.
ringId – The ring index or ring number.
-
status_t ENET_GetRxFrame(ENET_Type *base, enet_handle_t *handle, enet_rx_frame_struct_t *rxFrame, uint8_t ringId)
Receives one frame in specified BD ring with zero copy.
This function uses the user-defined allocation and free callbacks. Every time application gets one frame through this function, driver stores the buffer address(es) in enet_buffer_struct_t and allocate new buffer(s) for the BD(s). If there’s no memory buffer in the pool, this function drops current one frame to keep the Rx frame in BD ring is as fresh as possible.
Note
Application must provide a memory pool including at least BD number + n buffers in order for this function to work properly, because each BD must always take one buffer while driver is running, then other extra n buffer(s) can be taken by application. Here n is the ceil(max_frame_length(set by RCR) / bd_rx_size(set by MRBR)). Application must also provide an array structure in rxFrame->rxBuffArray with n index to receive one complete frame in any case.
- Parameters:
base – ENET peripheral base address.
handle – The ENET handler pointer. This is the same handler pointer used in the ENET_Init.
rxFrame – The received frame information structure provided by user.
ringId – The ring index or ring number.
- Return values:
kStatus_Success – Succeed to get one frame and allocate new memory for Rx buffer.
kStatus_ENET_RxFrameEmpty – There’s no Rx frame in the BD.
kStatus_ENET_RxFrameError – There’s issue in this receiving.
kStatus_ENET_RxFrameDrop – There’s no new buffer memory for BD, drop this frame.
-
status_t ENET_StartTxFrame(ENET_Type *base, enet_handle_t *handle, enet_tx_frame_struct_t *txFrame, uint8_t ringId)
Sends one frame in specified BD ring with zero copy.
This function supports scattered buffer transmit, user needs to provide the buffer array.
Note
Tx reclaim should be enabled to ensure the Tx buffer ownership can be given back to application after Tx is over.
- Parameters:
base – ENET peripheral base address.
handle – The ENET handler pointer. This is the same handler pointer used in the ENET_Init.
txFrame – The Tx frame structure.
ringId – The ring index or ring number.
- Return values:
kStatus_Success – Succeed to send one frame.
kStatus_ENET_TxFrameBusy – The BD is not ready for Tx or the reclaim operation still not finishs.
kStatus_ENET_TxFrameOverLen – The Tx frame length is over max ethernet frame length.
-
void ENET_TransmitIRQHandler(ENET_Type *base, enet_handle_t *handle)
The transmit IRQ handler.
- Parameters:
base – ENET peripheral base address.
handle – The ENET handler pointer.
-
void ENET_ReceiveIRQHandler(ENET_Type *base, enet_handle_t *handle)
The receive IRQ handler.
- Parameters:
base – ENET peripheral base address.
handle – The ENET handler pointer.
-
void ENET_ErrorIRQHandler(ENET_Type *base, enet_handle_t *handle)
Some special IRQ handler including the error, mii, wakeup irq handler.
- Parameters:
base – ENET peripheral base address.
handle – The ENET handler pointer.
-
void ENET_Ptp1588IRQHandler(ENET_Type *base)
the common IRQ handler for the 1588 irq handler.
This is used for the 1588 timer interrupt.
- Parameters:
base – ENET peripheral base address.
-
void ENET_CommonFrame0IRQHandler(ENET_Type *base)
the common IRQ handler for the tx/rx/error etc irq handler.
This is used for the combined tx/rx/error interrupt for single/mutli-ring (frame 0).
- Parameters:
base – ENET peripheral base address.
-
FSL_ENET_DRIVER_VERSION
Defines the driver version.
-
ENET_BUFFDESCRIPTOR_RX_EMPTY_MASK
Empty bit mask.
-
ENET_BUFFDESCRIPTOR_RX_SOFTOWNER1_MASK
Software owner one mask.
-
ENET_BUFFDESCRIPTOR_RX_WRAP_MASK
Next buffer descriptor is the start address.
-
ENET_BUFFDESCRIPTOR_RX_SOFTOWNER2_Mask
Software owner two mask.
-
ENET_BUFFDESCRIPTOR_RX_LAST_MASK
Last BD of the frame mask.
-
ENET_BUFFDESCRIPTOR_RX_MISS_MASK
Received because of the promiscuous mode.
-
ENET_BUFFDESCRIPTOR_RX_BROADCAST_MASK
Broadcast packet mask.
-
ENET_BUFFDESCRIPTOR_RX_MULTICAST_MASK
Multicast packet mask.
-
ENET_BUFFDESCRIPTOR_RX_LENVLIOLATE_MASK
Length violation mask.
-
ENET_BUFFDESCRIPTOR_RX_NOOCTET_MASK
Non-octet aligned frame mask.
-
ENET_BUFFDESCRIPTOR_RX_CRC_MASK
CRC error mask.
-
ENET_BUFFDESCRIPTOR_RX_OVERRUN_MASK
FIFO overrun mask.
-
ENET_BUFFDESCRIPTOR_RX_TRUNC_MASK
Frame is truncated mask.
-
ENET_BUFFDESCRIPTOR_TX_READY_MASK
Ready bit mask.
-
ENET_BUFFDESCRIPTOR_TX_SOFTOWENER1_MASK
Software owner one mask.
-
ENET_BUFFDESCRIPTOR_TX_WRAP_MASK
Wrap buffer descriptor mask.
-
ENET_BUFFDESCRIPTOR_TX_SOFTOWENER2_MASK
Software owner two mask.
-
ENET_BUFFDESCRIPTOR_TX_LAST_MASK
Last BD of the frame mask.
-
ENET_BUFFDESCRIPTOR_TX_TRANMITCRC_MASK
Transmit CRC mask.
-
ENET_FRAME_MAX_FRAMELEN
Default maximum Ethernet frame size without VLAN tag.
-
ENET_FRAME_VLAN_TAGLEN
Ethernet single VLAN tag size.
-
ENET_FRAME_CRC_LEN
CRC size in a frame.
-
ENET_FRAME_TX_LEN_LIMITATION(x)
-
ENET_FIFO_MIN_RX_FULL
ENET minimum receive FIFO full.
-
ENET_RX_MIN_BUFFERSIZE
ENET minimum buffer size.
-
ENET_PHY_MAXADDRESS
Maximum PHY address.
-
ENET_TX_INTERRUPT
Enet Tx interrupt flag.
-
ENET_RX_INTERRUPT
Enet Rx interrupt flag.
-
ENET_TS_INTERRUPT
Enet timestamp interrupt flag.
-
ENET_ERR_INTERRUPT
Enet error interrupt flag.
Defines the status return codes for transaction.
Values:
-
enumerator kStatus_ENET_InitMemoryFail
Init fails since buffer memory is not enough.
-
enumerator kStatus_ENET_RxFrameError
A frame received but data error happen.
-
enumerator kStatus_ENET_RxFrameFail
Failed to receive a frame.
-
enumerator kStatus_ENET_RxFrameEmpty
No frame arrive.
-
enumerator kStatus_ENET_RxFrameDrop
Rx frame is dropped since no buffer memory.
-
enumerator kStatus_ENET_TxFrameOverLen
Tx frame over length.
-
enumerator kStatus_ENET_TxFrameBusy
Tx buffer descriptors are under process.
-
enumerator kStatus_ENET_TxFrameFail
Transmit frame fail.
-
enumerator kStatus_ENET_InitMemoryFail
-
enum _enet_mii_mode
Defines the MII/RMII/RGMII mode for data interface between the MAC and the PHY.
Values:
-
enumerator kENET_MiiMode
MII mode for data interface.
-
enumerator kENET_RmiiMode
RMII mode for data interface.
-
enumerator kENET_RgmiiMode
RGMII mode for data interface.
-
enumerator kENET_MiiMode
-
enum _enet_mii_speed
Defines the 10/100/1000 Mbps speed for the MII data interface.
Notice: “kENET_MiiSpeed1000M” only supported when mii mode is “kENET_RgmiiMode”.
Values:
-
enumerator kENET_MiiSpeed10M
Speed 10 Mbps.
-
enumerator kENET_MiiSpeed100M
Speed 100 Mbps.
-
enumerator kENET_MiiSpeed1000M
Speed 1000M bps.
-
enumerator kENET_MiiSpeed10M
-
enum _enet_mii_duplex
Defines the half or full duplex for the MII data interface.
Values:
-
enumerator kENET_MiiHalfDuplex
Half duplex mode.
-
enumerator kENET_MiiFullDuplex
Full duplex mode.
-
enumerator kENET_MiiHalfDuplex
-
enum _enet_mii_write
Define the MII opcode for normal MDIO_CLAUSES_22 Frame.
Values:
-
enumerator kENET_MiiWriteNoCompliant
Write frame operation, but not MII-compliant.
-
enumerator kENET_MiiWriteValidFrame
Write frame operation for a valid MII management frame.
-
enumerator kENET_MiiWriteNoCompliant
-
enum _enet_mii_read
Defines the read operation for the MII management frame.
Values:
-
enumerator kENET_MiiReadValidFrame
Read frame operation for a valid MII management frame.
-
enumerator kENET_MiiReadNoCompliant
Read frame operation, but not MII-compliant.
-
enumerator kENET_MiiReadValidFrame
-
enum _enet_mii_extend_opcode
Define the MII opcode for extended MDIO_CLAUSES_45 Frame.
Values:
-
enumerator kENET_MiiAddrWrite_C45
Address Write operation.
-
enumerator kENET_MiiWriteFrame_C45
Write frame operation for a valid MII management frame.
-
enumerator kENET_MiiReadFrame_C45
Read frame operation for a valid MII management frame.
-
enumerator kENET_MiiAddrWrite_C45
-
enum _enet_special_control_flag
Defines a special configuration for ENET MAC controller.
These control flags are provided for special user requirements. Normally, these control flags are unused for ENET initialization. For special requirements, set the flags to macSpecialConfig in the enet_config_t. The kENET_ControlStoreAndFwdDisable is used to disable the FIFO store and forward. FIFO store and forward means that the FIFO read/send is started when a complete frame is stored in TX/RX FIFO. If this flag is set, configure rxFifoFullThreshold and txFifoWatermark in the enet_config_t.
Values:
-
enumerator kENET_ControlFlowControlEnable
Enable ENET flow control: pause frame.
-
enumerator kENET_ControlRxPayloadCheckEnable
Enable ENET receive payload length check.
-
enumerator kENET_ControlRxPadRemoveEnable
Padding is removed from received frames.
-
enumerator kENET_ControlRxBroadCastRejectEnable
Enable broadcast frame reject.
-
enumerator kENET_ControlMacAddrInsert
Enable MAC address insert.
-
enumerator kENET_ControlStoreAndFwdDisable
Enable FIFO store and forward.
-
enumerator kENET_ControlSMIPreambleDisable
Enable SMI preamble.
-
enumerator kENET_ControlPromiscuousEnable
Enable promiscuous mode.
-
enumerator kENET_ControlMIILoopEnable
Enable ENET MII loop back.
-
enumerator kENET_ControlVLANTagEnable
Enable normal VLAN (single vlan tag).
-
enumerator kENET_ControlSVLANEnable
Enable S-VLAN.
-
enumerator kENET_ControlVLANUseSecondTag
Enable extracting the second vlan tag for further processing.
-
enumerator kENET_ControlFlowControlEnable
-
enum _enet_interrupt_enable
List of interrupts supported by the peripheral. This enumeration uses one-bit encoding to allow a logical OR of multiple members. Members usually map to interrupt enable bits in one or more peripheral registers.
Values:
-
enumerator kENET_BabrInterrupt
Babbling receive error interrupt source
-
enumerator kENET_BabtInterrupt
Babbling transmit error interrupt source
-
enumerator kENET_GraceStopInterrupt
Graceful stop complete interrupt source
-
enumerator kENET_TxFrameInterrupt
TX FRAME interrupt source
-
enumerator kENET_TxBufferInterrupt
TX BUFFER interrupt source
-
enumerator kENET_RxFrameInterrupt
RX FRAME interrupt source
-
enumerator kENET_RxBufferInterrupt
RX BUFFER interrupt source
-
enumerator kENET_MiiInterrupt
MII interrupt source
-
enumerator kENET_EBusERInterrupt
Ethernet bus error interrupt source
-
enumerator kENET_LateCollisionInterrupt
Late collision interrupt source
-
enumerator kENET_RetryLimitInterrupt
Collision Retry Limit interrupt source
-
enumerator kENET_UnderrunInterrupt
Transmit FIFO underrun interrupt source
-
enumerator kENET_PayloadRxInterrupt
Payload Receive error interrupt source
-
enumerator kENET_WakeupInterrupt
WAKEUP interrupt source
-
enumerator kENET_TsAvailInterrupt
TS AVAIL interrupt source for PTP
-
enumerator kENET_TsTimerInterrupt
TS WRAP interrupt source for PTP
-
enumerator kENET_BabrInterrupt
-
enum _enet_event
Defines the common interrupt event for callback use.
Values:
-
enumerator kENET_RxEvent
Receive event.
-
enumerator kENET_TxEvent
Transmit event.
-
enumerator kENET_ErrEvent
Error event: BABR/BABT/EBERR/LC/RL/UN/PLR .
-
enumerator kENET_WakeUpEvent
Wake up from sleep mode event.
-
enumerator kENET_TimeStampEvent
Time stamp event.
-
enumerator kENET_TimeStampAvailEvent
Time stamp available event.
-
enumerator kENET_RxEvent
-
enum _enet_idle_slope
Defines certain idle slope for bandwidth fraction.
Values:
-
enumerator kENET_IdleSlope1
The bandwidth fraction is about 0.002.
-
enumerator kENET_IdleSlope2
The bandwidth fraction is about 0.003.
-
enumerator kENET_IdleSlope4
The bandwidth fraction is about 0.008.
-
enumerator kENET_IdleSlope8
The bandwidth fraction is about 0.02.
-
enumerator kENET_IdleSlope16
The bandwidth fraction is about 0.03.
-
enumerator kENET_IdleSlope32
The bandwidth fraction is about 0.06.
-
enumerator kENET_IdleSlope64
The bandwidth fraction is about 0.11.
-
enumerator kENET_IdleSlope128
The bandwidth fraction is about 0.20.
-
enumerator kENET_IdleSlope256
The bandwidth fraction is about 0.33.
-
enumerator kENET_IdleSlope384
The bandwidth fraction is about 0.43.
-
enumerator kENET_IdleSlope512
The bandwidth fraction is about 0.50.
-
enumerator kENET_IdleSlope640
The bandwidth fraction is about 0.56.
-
enumerator kENET_IdleSlope768
The bandwidth fraction is about 0.60.
-
enumerator kENET_IdleSlope896
The bandwidth fraction is about 0.64.
-
enumerator kENET_IdleSlope1024
The bandwidth fraction is about 0.67.
-
enumerator kENET_IdleSlope1152
The bandwidth fraction is about 0.69.
-
enumerator kENET_IdleSlope1280
The bandwidth fraction is about 0.71.
-
enumerator kENET_IdleSlope1408
The bandwidth fraction is about 0.73.
-
enumerator kENET_IdleSlope1536
The bandwidth fraction is about 0.75.
-
enumerator kENET_IdleSlope1
-
enum _enet_tx_accelerator
Defines the transmit accelerator configuration.
Note that the hardware does not insert ICMPv6 protocol checksums as mentioned in errata ERR052152.
Values:
-
enumerator kENET_TxAccelIsShift16Enabled
Transmit FIFO shift-16.
-
enumerator kENET_TxAccelIpCheckEnabled
Insert IP header checksum.
-
enumerator kENET_TxAccelProtoCheckEnabled
Insert protocol checksum (TCP, UDP, ICMPv4).
-
enumerator kENET_TxAccelIsShift16Enabled
-
enum _enet_rx_accelerator
Defines the receive accelerator configuration.
Note that the hardware does not validate ICMPv6 protocol checksums as mentioned in errata ERR052152.
Values:
-
enumerator kENET_RxAccelPadRemoveEnabled
Padding removal for short IP frames.
-
enumerator kENET_RxAccelIpCheckEnabled
Discard with wrong IP header checksum.
-
enumerator kENET_RxAccelProtoCheckEnabled
Discard with wrong protocol checksum (TCP, UDP, ICMPv4).
-
enumerator kENET_RxAccelMacCheckEnabled
Discard with Mac layer errors.
-
enumerator kENET_RxAccelisShift16Enabled
Receive FIFO shift-16.
-
enumerator kENET_RxAccelPadRemoveEnabled
-
typedef enum _enet_mii_mode enet_mii_mode_t
Defines the MII/RMII/RGMII mode for data interface between the MAC and the PHY.
-
typedef enum _enet_mii_speed enet_mii_speed_t
Defines the 10/100/1000 Mbps speed for the MII data interface.
Notice: “kENET_MiiSpeed1000M” only supported when mii mode is “kENET_RgmiiMode”.
-
typedef enum _enet_mii_duplex enet_mii_duplex_t
Defines the half or full duplex for the MII data interface.
-
typedef enum _enet_mii_write enet_mii_write_t
Define the MII opcode for normal MDIO_CLAUSES_22 Frame.
-
typedef enum _enet_mii_read enet_mii_read_t
Defines the read operation for the MII management frame.
-
typedef enum _enet_mii_extend_opcode enet_mii_extend_opcode
Define the MII opcode for extended MDIO_CLAUSES_45 Frame.
-
typedef enum _enet_special_control_flag enet_special_control_flag_t
Defines a special configuration for ENET MAC controller.
These control flags are provided for special user requirements. Normally, these control flags are unused for ENET initialization. For special requirements, set the flags to macSpecialConfig in the enet_config_t. The kENET_ControlStoreAndFwdDisable is used to disable the FIFO store and forward. FIFO store and forward means that the FIFO read/send is started when a complete frame is stored in TX/RX FIFO. If this flag is set, configure rxFifoFullThreshold and txFifoWatermark in the enet_config_t.
-
typedef enum _enet_interrupt_enable enet_interrupt_enable_t
List of interrupts supported by the peripheral. This enumeration uses one-bit encoding to allow a logical OR of multiple members. Members usually map to interrupt enable bits in one or more peripheral registers.
-
typedef enum _enet_event enet_event_t
Defines the common interrupt event for callback use.
-
typedef enum _enet_idle_slope enet_idle_slope_t
Defines certain idle slope for bandwidth fraction.
-
typedef enum _enet_tx_accelerator enet_tx_accelerator_t
Defines the transmit accelerator configuration.
Note that the hardware does not insert ICMPv6 protocol checksums as mentioned in errata ERR052152.
-
typedef enum _enet_rx_accelerator enet_rx_accelerator_t
Defines the receive accelerator configuration.
Note that the hardware does not validate ICMPv6 protocol checksums as mentioned in errata ERR052152.
-
typedef struct _enet_rx_bd_struct enet_rx_bd_struct_t
Defines the receive buffer descriptor structure for the little endian system.
-
typedef struct _enet_tx_bd_struct enet_tx_bd_struct_t
Defines the enhanced transmit buffer descriptor structure for the little endian system.
-
typedef struct _enet_data_error_stats enet_data_error_stats_t
Defines the ENET data error statistics structure.
-
typedef struct _enet_rx_frame_error enet_rx_frame_error_t
Defines the Rx frame error structure.
-
typedef struct _enet_transfer_stats enet_transfer_stats_t
Defines the ENET transfer statistics structure.
-
typedef struct enet_frame_info enet_frame_info_t
Defines the frame info structure.
-
typedef struct _enet_tx_dirty_ring enet_tx_dirty_ring_t
Defines the ENET transmit dirty addresses ring/queue structure.
-
typedef void *(*enet_rx_alloc_callback_t)(ENET_Type *base, void *userData, uint8_t ringId)
Defines the ENET Rx memory buffer alloc function pointer.
-
typedef void (*enet_rx_free_callback_t)(ENET_Type *base, void *buffer, void *userData, uint8_t ringId)
Defines the ENET Rx memory buffer free function pointer.
-
typedef struct _enet_buffer_config enet_buffer_config_t
Defines the receive buffer descriptor configuration structure.
Note that for the internal DMA requirements, the buffers have a corresponding alignment requirements.
The aligned receive and transmit buffer size must be evenly divisible by ENET_BUFF_ALIGNMENT. when the data buffers are in cacheable region when cache is enabled, all those size should be aligned to the maximum value of “ENET_BUFF_ALIGNMENT” and the cache line size.
The aligned transmit and receive buffer descriptor start address must be at least 64 bit aligned. However, it’s recommended to be evenly divisible by ENET_BUFF_ALIGNMENT. buffer descriptors should be put in non-cacheable region when cache is enabled.
The aligned transmit and receive data buffer start address must be evenly divisible by ENET_BUFF_ALIGNMENT. Receive buffers should be continuous with the total size equal to “rxBdNumber * rxBuffSizeAlign”. Transmit buffers should be continuous with the total size equal to “txBdNumber * txBuffSizeAlign”. when the data buffers are in cacheable region when cache is enabled, all those size should be aligned to the maximum value of “ENET_BUFF_ALIGNMENT” and the cache line size.
-
typedef struct _enet_intcoalesce_config enet_intcoalesce_config_t
Defines the interrupt coalescing configure structure.
-
typedef struct _enet_avb_config enet_avb_config_t
Defines the ENET AVB Configure structure.
This is used for to configure the extended ring 1 and ring 2.
The classification match format is (CMP3 << 12) | (CMP2 << 8) | (CMP1 << 4) | CMP0. composed of four 3-bit compared VLAN priority field cmp0~cmp3, cm0 ~ cmp3 are used in parallel.
If CMP1,2,3 are not unused, please set them to the same value as CMP0.
The idleSlope is used to calculate the Band Width fraction, BW fraction = 1 / (1 + 512/idleSlope). For avb configuration, the BW fraction of Class 1 and Class 2 combined must not exceed 0.75.
-
typedef struct _enet_handle enet_handle_t
-
typedef void (*enet_callback_t)(ENET_Type *base, enet_handle_t *handle, enet_event_t event, enet_frame_info_t *frameInfo, void *userData)
ENET callback function.
-
typedef struct _enet_config enet_config_t
Defines the basic configuration structure for the ENET device.
Note:
macSpecialConfig is used for a special control configuration, A logical OR of “enet_special_control_flag_t”. For a special configuration for MAC, set this parameter to 0.
txWatermark is used for a cut-through operation. It is in steps of 64 bytes: 0/1 - 64 bytes written to TX FIFO before transmission of a frame begins. 2 - 128 bytes written to TX FIFO …. 3 - 192 bytes written to TX FIFO …. The maximum of txWatermark is 0x2F - 4032 bytes written to TX FIFO …. txWatermark allows minimizing the transmit latency to set the txWatermark to 0 or 1 or for larger bus access latency 3 or larger due to contention for the system bus.
rxFifoFullThreshold is similar to the txWatermark for cut-through operation in RX. It is in 64-bit words. The minimum is ENET_FIFO_MIN_RX_FULL and the maximum is 0xFF. If the end of the frame is stored in FIFO and the frame size if smaller than the txWatermark, the frame is still transmitted. The rule is the same for rxFifoFullThreshold in the receive direction.
When “kENET_ControlFlowControlEnable” is set in the macSpecialConfig, ensure that the pauseDuration, rxFifoEmptyThreshold, and rxFifoStatEmptyThreshold are set for flow control enabled case.
When “kENET_ControlStoreAndFwdDisabled” is set in the macSpecialConfig, ensure that the rxFifoFullThreshold and txFifoWatermark are set for store and forward disable.
The rxAccelerConfig and txAccelerConfig default setting with 0 - accelerator are disabled. The “enet_tx_accelerator_t” and “enet_rx_accelerator_t” are recommended to be used to enable the transmit and receive accelerator. After the accelerators are enabled, the store and forward feature should be enabled. As a result, kENET_ControlStoreAndFwdDisabled should not be set.
The intCoalesceCfg can be used in the rx or tx enabled cases to decrese the CPU loading.
-
typedef struct _enet_tx_bd_ring enet_tx_bd_ring_t
Defines the ENET transmit buffer descriptor ring/queue structure.
-
typedef struct _enet_rx_bd_ring enet_rx_bd_ring_t
Defines the ENET receive buffer descriptor ring/queue structure.
-
typedef struct _enet_buffer_struct enet_buffer_struct_t
-
typedef struct _enet_rx_frame_attribute_struct enet_rx_frame_attribute_t
-
typedef struct _enet_rx_frame_struct enet_rx_frame_struct_t
-
typedef struct _enet_tx_frame_struct enet_tx_frame_struct_t
-
typedef void (*enet_isr_t)(ENET_Type *base, enet_handle_t *handle)
Define interrupt IRQ handler.
-
const clock_ip_name_t s_enetClock[]
Pointers to enet clocks for each instance.
-
const clock_ip_name_t s_enetExtraClock[]
-
uint32_t ENET_GetInstance(ENET_Type *base)
Get the ENET instance from peripheral base address.
- Parameters:
base – ENET peripheral base address.
- Returns:
ENET instance.
-
ENET_BUFFDESCRIPTOR_RX_ERR_MASK
Defines the receive error status flag mask.
-
struct _enet_rx_bd_struct
- #include <fsl_enet.h>
Defines the receive buffer descriptor structure for the little endian system.
Public Members
-
uint16_t length
Buffer descriptor data length.
-
uint16_t control
Buffer descriptor control and status.
-
uint32_t buffer
Data buffer pointer.
-
uint16_t length
-
struct _enet_tx_bd_struct
- #include <fsl_enet.h>
Defines the enhanced transmit buffer descriptor structure for the little endian system.
Public Members
-
uint16_t length
Buffer descriptor data length.
-
uint16_t control
Buffer descriptor control and status.
-
uint32_t buffer
Data buffer pointer.
-
uint16_t length
-
struct _enet_data_error_stats
- #include <fsl_enet.h>
Defines the ENET data error statistics structure.
Public Members
-
uint32_t statsRxLenGreaterErr
Receive length greater than RCR[MAX_FL].
-
uint32_t statsRxAlignErr
Receive non-octet alignment/
-
uint32_t statsRxFcsErr
Receive CRC error.
-
uint32_t statsRxOverRunErr
Receive over run.
-
uint32_t statsRxTruncateErr
Receive truncate.
-
uint32_t statsRxLenGreaterErr
-
struct _enet_rx_frame_error
- #include <fsl_enet.h>
Defines the Rx frame error structure.
Public Members
-
bool statsRxTruncateErr
Receive truncate.
-
bool statsRxOverRunErr
Receive over run.
-
bool statsRxFcsErr
Receive CRC error.
-
bool statsRxAlignErr
Receive non-octet alignment.
-
bool statsRxLenGreaterErr
Receive length greater than RCR[MAX_FL].
-
bool statsRxTruncateErr
-
struct _enet_transfer_stats
- #include <fsl_enet.h>
Defines the ENET transfer statistics structure.
Public Members
-
uint32_t statsRxFrameCount
Rx frame number.
-
uint32_t statsRxFrameOk
Good Rx frame number.
-
uint32_t statsRxCrcErr
Rx frame number with CRC error.
-
uint32_t statsRxAlignErr
Rx frame number with alignment error.
-
uint32_t statsRxDropInvalidSFD
Dropped frame number due to invalid SFD.
-
uint32_t statsRxFifoOverflowErr
Rx FIFO overflow count.
-
uint32_t statsTxFrameCount
Tx frame number.
-
uint32_t statsTxFrameOk
Good Tx frame number.
-
uint32_t statsTxCrcAlignErr
The transmit frame is error.
-
uint32_t statsTxFifoUnderRunErr
Tx FIFO underrun count.
-
uint32_t statsRxFrameCount
-
struct enet_frame_info
- #include <fsl_enet.h>
Defines the frame info structure.
Public Members
-
void *context
User specified data
-
void *context
-
struct _enet_tx_dirty_ring
- #include <fsl_enet.h>
Defines the ENET transmit dirty addresses ring/queue structure.
Public Members
-
enet_frame_info_t *txDirtyBase
Dirty buffer descriptor base address pointer.
-
uint16_t txGenIdx
tx generate index.
-
uint16_t txConsumIdx
tx consume index.
-
uint16_t txRingLen
tx ring length.
-
bool isFull
tx ring is full flag.
-
enet_frame_info_t *txDirtyBase
-
struct _enet_buffer_config
- #include <fsl_enet.h>
Defines the receive buffer descriptor configuration structure.
Note that for the internal DMA requirements, the buffers have a corresponding alignment requirements.
The aligned receive and transmit buffer size must be evenly divisible by ENET_BUFF_ALIGNMENT. when the data buffers are in cacheable region when cache is enabled, all those size should be aligned to the maximum value of “ENET_BUFF_ALIGNMENT” and the cache line size.
The aligned transmit and receive buffer descriptor start address must be at least 64 bit aligned. However, it’s recommended to be evenly divisible by ENET_BUFF_ALIGNMENT. buffer descriptors should be put in non-cacheable region when cache is enabled.
The aligned transmit and receive data buffer start address must be evenly divisible by ENET_BUFF_ALIGNMENT. Receive buffers should be continuous with the total size equal to “rxBdNumber * rxBuffSizeAlign”. Transmit buffers should be continuous with the total size equal to “txBdNumber * txBuffSizeAlign”. when the data buffers are in cacheable region when cache is enabled, all those size should be aligned to the maximum value of “ENET_BUFF_ALIGNMENT” and the cache line size.
Public Members
-
uint16_t rxBdNumber
Receive buffer descriptor number.
-
uint16_t txBdNumber
Transmit buffer descriptor number.
-
uint16_t rxBuffSizeAlign
Aligned receive data buffer size.
-
uint16_t txBuffSizeAlign
Aligned transmit data buffer size.
-
volatile enet_rx_bd_struct_t *rxBdStartAddrAlign
Aligned receive buffer descriptor start address: should be non-cacheable.
-
volatile enet_tx_bd_struct_t *txBdStartAddrAlign
Aligned transmit buffer descriptor start address: should be non-cacheable.
-
uint8_t *rxBufferAlign
Receive data buffer start address.
-
uint8_t *txBufferAlign
Transmit data buffer start address.
-
bool rxMaintainEnable
Receive buffer cache maintain.
-
bool txMaintainEnable
Transmit buffer cache maintain.
-
enet_frame_info_t *txFrameInfo
Transmit frame information start address.
-
struct _enet_intcoalesce_config
- #include <fsl_enet.h>
Defines the interrupt coalescing configure structure.
Public Members
-
uint8_t txCoalesceFrameCount[1]
Transmit interrupt coalescing frame count threshold.
-
uint16_t txCoalesceTimeCount[1]
Transmit interrupt coalescing timer count threshold.
-
uint8_t rxCoalesceFrameCount[1]
Receive interrupt coalescing frame count threshold.
-
uint16_t rxCoalesceTimeCount[1]
Receive interrupt coalescing timer count threshold.
-
uint8_t txCoalesceFrameCount[1]
-
struct _enet_avb_config
- #include <fsl_enet.h>
Defines the ENET AVB Configure structure.
This is used for to configure the extended ring 1 and ring 2.
The classification match format is (CMP3 << 12) | (CMP2 << 8) | (CMP1 << 4) | CMP0. composed of four 3-bit compared VLAN priority field cmp0~cmp3, cm0 ~ cmp3 are used in parallel.
If CMP1,2,3 are not unused, please set them to the same value as CMP0.
The idleSlope is used to calculate the Band Width fraction, BW fraction = 1 / (1 + 512/idleSlope). For avb configuration, the BW fraction of Class 1 and Class 2 combined must not exceed 0.75.
Public Members
-
uint16_t rxClassifyMatch[1 - 1]
The classification match value for the ring.
-
enet_idle_slope_t idleSlope[1 - 1]
The idle slope for certian bandwidth fraction.
-
struct _enet_config
- #include <fsl_enet.h>
Defines the basic configuration structure for the ENET device.
Note:
macSpecialConfig is used for a special control configuration, A logical OR of “enet_special_control_flag_t”. For a special configuration for MAC, set this parameter to 0.
txWatermark is used for a cut-through operation. It is in steps of 64 bytes: 0/1 - 64 bytes written to TX FIFO before transmission of a frame begins. 2 - 128 bytes written to TX FIFO …. 3 - 192 bytes written to TX FIFO …. The maximum of txWatermark is 0x2F - 4032 bytes written to TX FIFO …. txWatermark allows minimizing the transmit latency to set the txWatermark to 0 or 1 or for larger bus access latency 3 or larger due to contention for the system bus.
rxFifoFullThreshold is similar to the txWatermark for cut-through operation in RX. It is in 64-bit words. The minimum is ENET_FIFO_MIN_RX_FULL and the maximum is 0xFF. If the end of the frame is stored in FIFO and the frame size if smaller than the txWatermark, the frame is still transmitted. The rule is the same for rxFifoFullThreshold in the receive direction.
When “kENET_ControlFlowControlEnable” is set in the macSpecialConfig, ensure that the pauseDuration, rxFifoEmptyThreshold, and rxFifoStatEmptyThreshold are set for flow control enabled case.
When “kENET_ControlStoreAndFwdDisabled” is set in the macSpecialConfig, ensure that the rxFifoFullThreshold and txFifoWatermark are set for store and forward disable.
The rxAccelerConfig and txAccelerConfig default setting with 0 - accelerator are disabled. The “enet_tx_accelerator_t” and “enet_rx_accelerator_t” are recommended to be used to enable the transmit and receive accelerator. After the accelerators are enabled, the store and forward feature should be enabled. As a result, kENET_ControlStoreAndFwdDisabled should not be set.
The intCoalesceCfg can be used in the rx or tx enabled cases to decrese the CPU loading.
Public Members
-
uint32_t macSpecialConfig
Mac special configuration. A logical OR of “enet_special_control_flag_t”.
-
uint32_t interrupt
Mac interrupt source. A logical OR of “enet_interrupt_enable_t”.
-
uint16_t rxMaxFrameLen
Receive maximum frame length.
-
enet_mii_mode_t miiMode
MII mode.
-
enet_mii_speed_t miiSpeed
MII Speed.
-
enet_mii_duplex_t miiDuplex
MII duplex.
-
uint8_t rxAccelerConfig
Receive accelerator, A logical OR of “enet_rx_accelerator_t”.
-
uint8_t txAccelerConfig
Transmit accelerator, A logical OR of “enet_rx_accelerator_t”.
-
uint16_t pauseDuration
For flow control enabled case: Pause duration.
-
uint8_t rxFifoEmptyThreshold
For flow control enabled case: when RX FIFO level reaches this value, it makes MAC generate XOFF pause frame.
-
uint8_t rxFifoStatEmptyThreshold
For flow control enabled case: number of frames in the receive FIFO, independent of size, that can be accept. If the limit is reached, reception continues and a pause frame is triggered.
-
uint8_t rxFifoFullThreshold
For store and forward disable case, the data required in RX FIFO to notify the MAC receive ready status.
-
uint8_t txFifoWatermark
For store and forward disable case, the data required in TX FIFO before a frame transmit start.
-
enet_intcoalesce_config_t *intCoalesceCfg
If the interrupt coalsecence is not required in the ring n(0,1,2), please set to NULL.
-
uint8_t ringNum
Number of used rings. default with 1 — single ring.
-
enet_rx_alloc_callback_t rxBuffAlloc
Callback function to alloc memory, must be provided for zero-copy Rx.
-
enet_rx_free_callback_t rxBuffFree
Callback function to free memory, must be provided for zero-copy Rx.
-
enet_callback_t callback
General callback function.
-
void *userData
Callback function parameter.
-
struct _enet_tx_bd_ring
- #include <fsl_enet.h>
Defines the ENET transmit buffer descriptor ring/queue structure.
Public Members
-
volatile enet_tx_bd_struct_t *txBdBase
Buffer descriptor base address pointer.
-
uint16_t txGenIdx
The current available transmit buffer descriptor pointer.
-
uint16_t txConsumIdx
Transmit consume index.
-
volatile uint16_t txDescUsed
Transmit descriptor used number.
-
uint16_t txRingLen
Transmit ring length.
-
volatile enet_tx_bd_struct_t *txBdBase
-
struct _enet_rx_bd_ring
- #include <fsl_enet.h>
Defines the ENET receive buffer descriptor ring/queue structure.
Public Members
-
volatile enet_rx_bd_struct_t *rxBdBase
Buffer descriptor base address pointer.
-
uint16_t rxGenIdx
The current available receive buffer descriptor pointer.
-
uint16_t rxRingLen
Receive ring length.
-
volatile enet_rx_bd_struct_t *rxBdBase
-
struct _enet_handle
- #include <fsl_enet.h>
Defines the ENET handler structure.
Public Members
-
enet_rx_bd_ring_t rxBdRing[1]
Receive buffer descriptor.
-
enet_tx_bd_ring_t txBdRing[1]
Transmit buffer descriptor.
-
uint16_t rxBuffSizeAlign[1]
Receive buffer size alignment.
-
uint16_t txBuffSizeAlign[1]
Transmit buffer size alignment.
-
bool rxMaintainEnable[1]
Receive buffer cache maintain.
-
bool txMaintainEnable[1]
Transmit buffer cache maintain.
-
uint8_t ringNum
Number of used rings.
-
enet_callback_t callback
Callback function.
-
void *userData
Callback function parameter.
-
enet_tx_dirty_ring_t txDirtyRing[1]
Ring to store tx frame information.
-
bool txReclaimEnable[1]
Tx reclaim enable flag.
-
enet_rx_alloc_callback_t rxBuffAlloc
Callback function to alloc memory for zero copy Rx.
-
enet_rx_free_callback_t rxBuffFree
Callback function to free memory for zero copy Rx.
-
uint8_t multicastCount[64]
Multicast collisions counter
-
uint32_t enetClock
The clock of enet peripheral, to caculate core cycles for PTP timestamp.
-
uint32_t tsDelayCount
The count of core cycles for PTP timestamp capture delay.
-
enet_rx_bd_ring_t rxBdRing[1]
-
struct _enet_buffer_struct
- #include <fsl_enet.h>
Public Members
-
void *buffer
The buffer store the whole or partial frame.
-
uint16_t length
The byte length of this buffer.
-
void *buffer
-
struct _enet_rx_frame_attribute_struct
- #include <fsl_enet.h>
Public Members
-
bool promiscuous
This frame is received because of promiscuous mode.
-
bool promiscuous
-
struct _enet_rx_frame_struct
- #include <fsl_enet.h>
Public Members
-
enet_buffer_struct_t *rxBuffArray
Rx frame buffer structure.
-
uint16_t totLen
Rx frame total length.
-
enet_rx_frame_attribute_t rxAttribute
Rx frame attribute structure.
-
enet_rx_frame_error_t rxFrameError
Rx frame error.
-
enet_buffer_struct_t *rxBuffArray
-
struct _enet_tx_frame_struct
- #include <fsl_enet.h>
Public Members
-
enet_buffer_struct_t *txBuffArray
Tx frame buffer structure.
-
uint32_t txBuffNum
Buffer number of this Tx frame.
-
void *context
Driver reclaims and gives it in Tx over callback, usually store network packet header.
-
enet_buffer_struct_t *txBuffArray
EWM: External Watchdog Monitor Driver
-
void EWM_Init(EWM_Type *base, const ewm_config_t *config)
Initializes the EWM peripheral.
This function is used to initialize the EWM. After calling, the EWM runs immediately according to the configuration. Note that, except for the interrupt enable control bit, other control bits and registers are write once after a CPU reset. Modifying them more than once generates a bus transfer error.
This is an example.
ewm_config_t config; EWM_GetDefaultConfig(&config); config.compareHighValue = 0xAAU; EWM_Init(ewm_base,&config);
- Parameters:
base – EWM peripheral base address
config – The configuration of the EWM
-
void EWM_Deinit(EWM_Type *base)
Deinitializes the EWM peripheral.
This function is used to shut down the EWM.
- Parameters:
base – EWM peripheral base address
-
void EWM_GetDefaultConfig(ewm_config_t *config)
Initializes the EWM configuration structure.
This function initializes the EWM configuration structure to default values. The default values are as follows.
ewmConfig->enableEwm = true; ewmConfig->enableEwmInput = false; ewmConfig->setInputAssertLogic = false; ewmConfig->enableInterrupt = false; ewmConfig->ewm_lpo_clock_source_t = kEWM_LpoClockSource0; ewmConfig->prescaler = 0; ewmConfig->compareLowValue = 0; ewmConfig->compareHighValue = 0xFEU;
See also
ewm_config_t
- Parameters:
config – Pointer to the EWM configuration structure.
-
static inline void EWM_EnableInterrupts(EWM_Type *base, uint32_t mask)
Enables the EWM interrupt.
This function enables the EWM interrupt.
- Parameters:
base – EWM peripheral base address
mask – The interrupts to enable The parameter can be combination of the following source if defined
kEWM_InterruptEnable
-
static inline void EWM_DisableInterrupts(EWM_Type *base, uint32_t mask)
Disables the EWM interrupt.
This function enables the EWM interrupt.
- Parameters:
base – EWM peripheral base address
mask – The interrupts to disable The parameter can be combination of the following source if defined
kEWM_InterruptEnable
-
static inline uint32_t EWM_GetStatusFlags(EWM_Type *base)
Gets all status flags.
This function gets all status flags.
This is an example for getting the running flag.
uint32_t status; status = EWM_GetStatusFlags(ewm_base) & kEWM_RunningFlag;
See also
_ewm_status_flags_t
True: a related status flag has been set.
False: a related status flag is not set.
- Parameters:
base – EWM peripheral base address
- Returns:
State of the status flag: asserted (true) or not-asserted (false).
-
void EWM_Refresh(EWM_Type *base)
Services the EWM.
This function resets the EWM counter to zero.
- Parameters:
base – EWM peripheral base address
-
FSL_EWM_DRIVER_VERSION
EWM driver version 2.0.3.
-
enum _ewm_lpo_clock_source
Describes EWM clock source.
Values:
-
enumerator kEWM_LpoClockSource0
EWM clock sourced from lpo_clk[0]
-
enumerator kEWM_LpoClockSource1
EWM clock sourced from lpo_clk[1]
-
enumerator kEWM_LpoClockSource2
EWM clock sourced from lpo_clk[2]
-
enumerator kEWM_LpoClockSource3
EWM clock sourced from lpo_clk[3]
-
enumerator kEWM_LpoClockSource0
-
enum _ewm_interrupt_enable_t
EWM interrupt configuration structure with default settings all disabled.
This structure contains the settings for all of EWM interrupt configurations.
Values:
-
enumerator kEWM_InterruptEnable
Enable the EWM to generate an interrupt
-
enumerator kEWM_InterruptEnable
-
enum _ewm_status_flags_t
EWM status flags.
This structure contains the constants for the EWM status flags for use in the EWM functions.
Values:
-
enumerator kEWM_RunningFlag
Running flag, set when EWM is enabled
-
enumerator kEWM_RunningFlag
-
typedef enum _ewm_lpo_clock_source ewm_lpo_clock_source_t
Describes EWM clock source.
-
typedef struct _ewm_config ewm_config_t
Data structure for EWM configuration.
This structure is used to configure the EWM.
-
struct _ewm_config
- #include <fsl_ewm.h>
Data structure for EWM configuration.
This structure is used to configure the EWM.
Public Members
-
bool enableEwm
Enable EWM module
-
bool enableEwmInput
Enable EWM_in input
-
bool setInputAssertLogic
EWM_in signal assertion state
-
bool enableInterrupt
Enable EWM interrupt
-
ewm_lpo_clock_source_t clockSource
Clock source select
-
uint8_t prescaler
Clock prescaler value
-
uint8_t compareLowValue
Compare low-register value
-
uint8_t compareHighValue
Compare high-register value
-
bool enableEwm
FlexCAN: Flex Controller Area Network Driver
FlexCAN Driver
-
bool FLEXCAN_IsInstanceHasFDMode(CAN_Type *base)
Determine whether the FlexCAN instance support CAN FD mode at run time.
Note
Use this API only if different soc parts share the SOC part name macro define. Otherwise, a different SOC part name can be used to determine at compile time whether the FlexCAN instance supports CAN FD mode or not. If need use this API to determine if CAN FD mode is supported, the FLEXCAN_Init function needs to be executed first, and then call this API and use the return to value determines whether to supports CAN FD mode, if return true, continue calling FLEXCAN_FDInit to enable CAN FD mode.
- Parameters:
base – FlexCAN peripheral base address.
- Returns:
return TRUE if instance support CAN FD mode, FALSE if instance only support classic CAN (2.0) mode.
-
void FLEXCAN_EnterFreezeMode(CAN_Type *base)
Enter FlexCAN Freeze Mode.
This function makes the FlexCAN work under Freeze Mode.
- Parameters:
base – FlexCAN peripheral base address.
-
void FLEXCAN_ExitFreezeMode(CAN_Type *base)
Exit FlexCAN Freeze Mode.
This function makes the FlexCAN leave Freeze Mode.
- Parameters:
base – FlexCAN peripheral base address.
-
uint32_t FLEXCAN_GetInstance(CAN_Type *base)
Get the FlexCAN instance from peripheral base address.
- Parameters:
base – FlexCAN peripheral base address.
- Returns:
FlexCAN instance.
-
bool FLEXCAN_CalculateImprovedTimingValues(CAN_Type *base, uint32_t bitRate, uint32_t sourceClock_Hz, flexcan_timing_config_t *pTimingConfig)
Calculates the improved timing values by specific bit Rates for classical CAN.
This function use to calculates the Classical CAN timing values according to the given bit rate. The Calculated timing values will be set in CTRL1/CBT/ENCBT register. The calculation is based on the recommendation of the CiA 301 v4.2.0 and previous version document.
- Parameters:
base – FlexCAN peripheral base address.
bitRate – The classical CAN speed in bps defined by user, should be less than or equal to 1Mbps.
sourceClock_Hz – The Source clock frequency in Hz.
pTimingConfig – Pointer to the FlexCAN timing configuration structure.
- Returns:
TRUE if timing configuration found, FALSE if failed to find configuration.
-
void FLEXCAN_Init(CAN_Type *base, const flexcan_config_t *pConfig, uint32_t sourceClock_Hz)
Initializes a FlexCAN instance.
This function initializes the FlexCAN module with user-defined settings. This example shows how to set up the flexcan_config_t parameters and how to call the FLEXCAN_Init function by passing in these parameters.
flexcan_config_t flexcanConfig; flexcanConfig.clkSrc = kFLEXCAN_ClkSrc0; flexcanConfig.bitRate = 1000000U; flexcanConfig.maxMbNum = 16; flexcanConfig.enableLoopBack = false; flexcanConfig.enableSelfWakeup = false; flexcanConfig.enableIndividMask = false; flexcanConfig.enableDoze = false; flexcanConfig.disableSelfReception = false; flexcanConfig.enableListenOnlyMode = false; flexcanConfig.timingConfig = timingConfig; FLEXCAN_Init(CAN0, &flexcanConfig, 40000000UL);
- Parameters:
base – FlexCAN peripheral base address.
pConfig – Pointer to the user-defined configuration structure.
sourceClock_Hz – FlexCAN Protocol Engine clock source frequency in Hz.
-
bool FLEXCAN_FDCalculateImprovedTimingValues(CAN_Type *base, uint32_t bitRate, uint32_t bitRateFD, uint32_t sourceClock_Hz, flexcan_timing_config_t *pTimingConfig)
Calculates the improved timing values by specific bit rates for CANFD.
This function use to calculates the CANFD timing values according to the given nominal phase bit rate and data phase bit rate. The Calculated timing values will be set in CBT/ENCBT and FDCBT/EDCBT registers. The calculation is based on the recommendation of the CiA 1301 v1.0.0 document.
- Parameters:
base – FlexCAN peripheral base address.
bitRate – The CANFD bus control speed in bps defined by user.
bitRateFD – The CAN FD data phase speed in bps defined by user. Equal to bitRate means disable bit rate switching.
sourceClock_Hz – The Source clock frequency in Hz.
pTimingConfig – Pointer to the FlexCAN timing configuration structure.
- Returns:
TRUE if timing configuration found, FALSE if failed to find configuration
-
void FLEXCAN_FDInit(CAN_Type *base, const flexcan_config_t *pConfig, uint32_t sourceClock_Hz, flexcan_mb_size_t dataSize, bool brs)
Initializes a FlexCAN instance.
This function initializes the FlexCAN module with user-defined settings. This example shows how to set up the flexcan_config_t parameters and how to call the FLEXCAN_FDInit function by passing in these parameters.
flexcan_config_t flexcanConfig; flexcanConfig.clkSrc = kFLEXCAN_ClkSrc0; flexcanConfig.bitRate = 1000000U; flexcanConfig.bitRateFD = 2000000U; flexcanConfig.maxMbNum = 16; flexcanConfig.enableLoopBack = false; flexcanConfig.enableSelfWakeup = false; flexcanConfig.enableIndividMask = false; flexcanConfig.disableSelfReception = false; flexcanConfig.enableListenOnlyMode = false; flexcanConfig.enableDoze = false; flexcanConfig.timingConfig = timingConfig; FLEXCAN_FDInit(CAN0, &flexcanConfig, 80000000UL, kFLEXCAN_16BperMB, true);
- Parameters:
base – FlexCAN peripheral base address.
pConfig – Pointer to the user-defined configuration structure.
sourceClock_Hz – FlexCAN Protocol Engine clock source frequency in Hz.
dataSize – FlexCAN Message Buffer payload size. The actual transmitted or received CAN FD frame data size needs to be less than or equal to this value.
brs – True if bit rate switch is enabled in FD mode.
-
void FLEXCAN_Deinit(CAN_Type *base)
De-initializes a FlexCAN instance.
This function disables the FlexCAN module clock and sets all register values to the reset value.
- Parameters:
base – FlexCAN peripheral base address.
-
void FLEXCAN_GetDefaultConfig(flexcan_config_t *pConfig)
Gets the default configuration structure.
This function initializes the FlexCAN configuration structure to default values. The default values are as follows. flexcanConfig->clkSrc = kFLEXCAN_ClkSrc0; flexcanConfig->bitRate = 1000000U; flexcanConfig->bitRateFD = 2000000U; flexcanConfig->maxMbNum = 16; flexcanConfig->enableLoopBack = false; flexcanConfig->enableSelfWakeup = false; flexcanConfig->enableIndividMask = false; flexcanConfig->disableSelfReception = false; flexcanConfig->enableListenOnlyMode = false; flexcanConfig->enableDoze = false; flexcanConfig->enablePretendedeNetworking = false; flexcanConfig->enableMemoryErrorControl = true; flexcanConfig->enableNonCorrectableErrorEnterFreeze = true; flexcanConfig->enableTransceiverDelayMeasure = true; flexcanConfig->enableRemoteRequestFrameStored = true; flexcanConfig->payloadEndianness = kFLEXCAN_bigEndian; flexcanConfig.timingConfig = timingConfig;
- Parameters:
pConfig – Pointer to the FlexCAN configuration structure.
-
void FLEXCAN_SetTimingConfig(CAN_Type *base, const flexcan_timing_config_t *pConfig)
Sets the FlexCAN classical CAN protocol timing characteristic.
This function gives user settings to classical CAN or CAN FD nominal phase timing characteristic. The function is for an experienced user. For less experienced users, call the FLEXCAN_SetBitRate() instead.
Note
Calling FLEXCAN_SetTimingConfig() overrides the bit rate set in FLEXCAN_Init() or FLEXCAN_SetBitRate().
- Parameters:
base – FlexCAN peripheral base address.
pConfig – Pointer to the timing configuration structure.
-
status_t FLEXCAN_SetBitRate(CAN_Type *base, uint32_t sourceClock_Hz, uint32_t bitRate_Bps)
Set bit rate of FlexCAN classical CAN frame or CAN FD frame nominal phase.
This function set the bit rate of classical CAN frame or CAN FD frame nominal phase base on FLEXCAN_CalculateImprovedTimingValues() API calculated timing values.
Note
Calling FLEXCAN_SetBitRate() overrides the bit rate set in FLEXCAN_Init().
- Parameters:
base – FlexCAN peripheral base address.
sourceClock_Hz – Source Clock in Hz.
bitRate_Bps – Bit rate in Bps.
- Returns:
kStatus_Success - Set CAN baud rate (only Nominal phase) successfully.
-
void FLEXCAN_SetFDTimingConfig(CAN_Type *base, const flexcan_timing_config_t *pConfig)
Sets the FlexCAN CANFD data phase timing characteristic.
This function gives user settings to CANFD data phase timing characteristic. The function is for an experienced user. For less experienced users, call the FLEXCAN_SetFDBitRate() to set both Nominal/Data bit Rate instead.
Note
Calling FLEXCAN_SetFDTimingConfig() overrides the data phase bit rate set in FLEXCAN_FDInit()/FLEXCAN_SetFDBitRate().
- Parameters:
base – FlexCAN peripheral base address.
pConfig – Pointer to the timing configuration structure.
-
status_t FLEXCAN_SetFDBitRate(CAN_Type *base, uint32_t sourceClock_Hz, uint32_t bitRateN_Bps, uint32_t bitRateD_Bps)
Set bit rate of FlexCAN FD frame.
This function set the baud rate of FLEXCAN FD base on FLEXCAN_FDCalculateImprovedTimingValues() API calculated timing values.
- Parameters:
base – FlexCAN peripheral base address.
sourceClock_Hz – Source Clock in Hz.
bitRateN_Bps – Nominal bit Rate in Bps.
bitRateD_Bps – Data bit Rate in Bps.
- Returns:
kStatus_Success - Set CAN FD bit rate (include Nominal and Data phase) successfully.
-
void FLEXCAN_SetRxMbGlobalMask(CAN_Type *base, uint32_t mask)
Sets the FlexCAN receive message buffer global mask.
This function sets the global mask for the FlexCAN message buffer in a matching process. The configuration is only effective when the Rx individual mask is disabled in the FLEXCAN_Init().
- Parameters:
base – FlexCAN peripheral base address.
mask – Rx Message Buffer Global Mask value.
-
void FLEXCAN_SetRxFifoGlobalMask(CAN_Type *base, uint32_t mask)
Sets the FlexCAN receive FIFO global mask.
This function sets the global mask for FlexCAN FIFO in a matching process.
- Parameters:
base – FlexCAN peripheral base address.
mask – Rx Fifo Global Mask value.
-
void FLEXCAN_SetRxIndividualMask(CAN_Type *base, uint8_t maskIdx, uint32_t mask)
Sets the FlexCAN receive individual mask.
This function sets the individual mask for the FlexCAN matching process. The configuration is only effective when the Rx individual mask is enabled in the FLEXCAN_Init(). If the Rx FIFO is disabled, the individual mask is applied to the corresponding Message Buffer. If the Rx FIFO is enabled, the individual mask for Rx FIFO occupied Message Buffer is applied to the Rx Filter with the same index. Note that only the first 32 individual masks can be used as the Rx FIFO filter mask.
- Parameters:
base – FlexCAN peripheral base address.
maskIdx – The Index of individual Mask.
mask – Rx Individual Mask value.
-
void FLEXCAN_SetTxMbConfig(CAN_Type *base, uint8_t mbIdx, bool enable)
Configures a FlexCAN transmit message buffer.
This function aborts the previous transmission, cleans the Message Buffer, and configures it as a Transmit Message Buffer.
- Parameters:
base – FlexCAN peripheral base address.
mbIdx – The Message Buffer index.
enable – Enable/disable Tx Message Buffer.
true: Enable Tx Message Buffer.
false: Disable Tx Message Buffer.
-
void FLEXCAN_SetRxMbConfig(CAN_Type *base, uint8_t mbIdx, const flexcan_rx_mb_config_t *pRxMbConfig, bool enable)
Configures a FlexCAN Receive Message Buffer.
This function cleans a FlexCAN build-in Message Buffer and configures it as a Receive Message Buffer. User should invoke this API when CTRL2[RRS]=1. When CTRL2[RRS]=1, frame’s ID is compared to the IDs of the receive mailboxes with the CODE field configured as kFLEXCAN_RxMbEmpty, kFLEXCAN_RxMbFull or kFLEXCAN_RxMbOverrun. Message buffer will store the remote frame in the same fashion of a data frame. No automatic remote response frame will be generated. User need to setup another message buffer to respond remote request.
- Parameters:
base – FlexCAN peripheral base address.
mbIdx – The Message Buffer index.
pRxMbConfig – Pointer to the FlexCAN Message Buffer configuration structure.
enable – Enable/disable Rx Message Buffer.
true: Enable Rx Message Buffer.
false: Disable Rx Message Buffer.
-
void FLEXCAN_SetFDTxMbConfig(CAN_Type *base, uint8_t mbIdx, bool enable)
Configures a FlexCAN transmit message buffer.
This function aborts the previous transmission, cleans the Message Buffer, and configures it as a Transmit Message Buffer.
- Parameters:
base – FlexCAN peripheral base address.
mbIdx – The Message Buffer index.
enable – Enable/disable Tx Message Buffer.
true: Enable Tx Message Buffer.
false: Disable Tx Message Buffer.
-
void FLEXCAN_SetFDRxMbConfig(CAN_Type *base, uint8_t mbIdx, const flexcan_rx_mb_config_t *pRxMbConfig, bool enable)
Configures a FlexCAN Receive Message Buffer.
This function cleans a FlexCAN build-in Message Buffer and configures it as a Receive Message Buffer.
- Parameters:
base – FlexCAN peripheral base address.
mbIdx – The Message Buffer index.
pRxMbConfig – Pointer to the FlexCAN Message Buffer configuration structure.
enable – Enable/disable Rx Message Buffer.
true: Enable Rx Message Buffer.
false: Disable Rx Message Buffer.
-
void FLEXCAN_SetRemoteResponseMbConfig(CAN_Type *base, uint8_t mbIdx, const flexcan_frame_t *pFrame)
Configures a FlexCAN Remote Response Message Buffer.
User should invoke this API when CTRL2[RRS]=0. When CTRL2[RRS]=0, frame’s ID is compared to the IDs of the receive mailboxes with the CODE field configured as kFLEXCAN_RxMbRanswer. If there is a matching ID, then this mailbox content will be transmitted as response. The received remote request frame is not stored in receive buffer. It is only used to trigger a transmission of a frame in response.
- Parameters:
base – FlexCAN peripheral base address.
mbIdx – The Message Buffer index.
pFrame – Pointer to CAN message frame structure for response.
-
void FLEXCAN_SetRxFifoConfig(CAN_Type *base, const flexcan_rx_fifo_config_t *pRxFifoConfig, bool enable)
Configures the FlexCAN Legacy Rx FIFO.
This function configures the FlexCAN Rx FIFO with given configuration.
Note
Legacy Rx FIFO only can receive classic CAN message.
- Parameters:
base – FlexCAN peripheral base address.
pRxFifoConfig – Pointer to the FlexCAN Legacy Rx FIFO configuration structure. Can be NULL when enable parameter is false.
enable – Enable/disable Legacy Rx FIFO.
true: Enable Legacy Rx FIFO.
false: Disable Legacy Rx FIFO.
-
void FLEXCAN_SetPNConfig(CAN_Type *base, const flexcan_pn_config_t *pConfig)
Configures the FlexCAN Pretended Networking mode.
This function configures the FlexCAN Pretended Networking mode with given configuration.
- Parameters:
base – FlexCAN peripheral base address.
pConfig – Pointer to the FlexCAN Rx FIFO configuration structure.
-
static inline uint64_t FLEXCAN_GetStatusFlags(CAN_Type *base)
Gets the FlexCAN module interrupt flags.
This function gets all FlexCAN status flags. The flags are returned as the logical OR value of the enumerators _flexcan_flags. To check the specific status, compare the return value with enumerators in _flexcan_flags.
- Parameters:
base – FlexCAN peripheral base address.
- Returns:
FlexCAN status flags which are ORed by the enumerators in the _flexcan_flags.
-
static inline void FLEXCAN_ClearStatusFlags(CAN_Type *base, uint64_t mask)
Clears status flags with the provided mask.
This function clears the FlexCAN status flags with a provided mask. An automatically cleared flag can’t be cleared by this function.
- Parameters:
base – FlexCAN peripheral base address.
mask – The status flags to be cleared, it is logical OR value of _flexcan_flags.
-
static inline void FLEXCAN_GetBusErrCount(CAN_Type *base, uint8_t *txErrBuf, uint8_t *rxErrBuf)
Gets the FlexCAN Bus Error Counter value.
This function gets the FlexCAN Bus Error Counter value for both Tx and Rx direction. These values may be needed in the upper layer error handling.
- Parameters:
base – FlexCAN peripheral base address.
txErrBuf – Buffer to store Tx Error Counter value.
rxErrBuf – Buffer to store Rx Error Counter value.
-
static inline uint64_t FLEXCAN_GetMbStatusFlags(CAN_Type *base, uint64_t mask)
Gets the FlexCAN Message Buffer interrupt flags.
This function gets the interrupt flags of a given Message Buffers.
- Parameters:
base – FlexCAN peripheral base address.
mask – The ORed FlexCAN Message Buffer mask.
- Returns:
The status of given Message Buffers.
-
static inline uint64_t FLEXCAN_GetHigh64MbStatusFlags(CAN_Type *base, uint64_t mask)
Gets the FlexCAN High 64 Message Buffer interrupt flags.
Valid only if the number of available MBs exceeds 64.
- Parameters:
base – FlexCAN peripheral base address.
mask – The ORed FlexCAN Message Buffer mask.
- Returns:
The status of given Message Buffers.
-
static inline void FLEXCAN_ClearMbStatusFlags(CAN_Type *base, uint64_t mask)
Clears the FlexCAN Message Buffer interrupt flags.
This function clears the interrupt flags of a given Message Buffers.
- Parameters:
base – FlexCAN peripheral base address.
mask – The ORed FlexCAN Message Buffer mask.
-
static inline void FLEXCAN_ClearHigh64MbStatusFlags(CAN_Type *base, uint64_t mask)
Clears the FlexCAN High 64 Message Buffer interrupt flags.
Valid only if the number of available MBs exceeds 64.
- Parameters:
base – FlexCAN peripheral base address.
mask – The ORed FlexCAN Message Buffer mask.
-
void FLEXCAN_GetMemoryErrorReportStatus(CAN_Type *base, flexcan_memory_error_report_status_t *errorStatus)
Gets the FlexCAN Memory Error Report registers status.
This function gets the FlexCAN Memory Error Report registers status.
- Parameters:
base – FlexCAN peripheral base address.
errorStatus – Pointer to FlexCAN Memory Error Report registers status structure.
-
static inline uint8_t FLEXCAN_GetPNMatchCount(CAN_Type *base)
Gets the FlexCAN Number of Matches when in Pretended Networking.
This function gets the number of times a given message has matched the predefined filtering criteria for ID and/or PL before a wakeup event.
- Parameters:
base – FlexCAN peripheral base address.
- Returns:
The number of received wake up msessages.
-
static inline void FLEXCAN_EnableInterrupts(CAN_Type *base, uint64_t mask)
Enables FlexCAN interrupts according to the provided mask.
This function enables the FlexCAN interrupts according to the provided mask. The mask is a logical OR of enumeration members, see _flexcan_interrupt_enable.
- Parameters:
base – FlexCAN peripheral base address.
mask – The interrupts to enable. Logical OR of _flexcan_interrupt_enable.
-
static inline void FLEXCAN_DisableInterrupts(CAN_Type *base, uint64_t mask)
Disables FlexCAN interrupts according to the provided mask.
This function disables the FlexCAN interrupts according to the provided mask. The mask is a logical OR of enumeration members, see _flexcan_interrupt_enable.
- Parameters:
base – FlexCAN peripheral base address.
mask – The interrupts to disable. Logical OR of _flexcan_interrupt_enable.
-
static inline void FLEXCAN_EnableMbInterrupts(CAN_Type *base, uint64_t mask)
Enables FlexCAN Message Buffer interrupts.
This function enables the interrupts of given Message Buffers.
- Parameters:
base – FlexCAN peripheral base address.
mask – The ORed FlexCAN Message Buffer mask.
-
static inline void FLEXCAN_EnableHigh64MbInterrupts(CAN_Type *base, uint64_t mask)
Enables FlexCAN high 64 Message Buffer interrupts.
Valid only if the number of available MBs exceeds 64.
- Parameters:
base – FlexCAN peripheral base address.
mask – The ORed FlexCAN Message Buffer mask.
-
static inline void FLEXCAN_DisableMbInterrupts(CAN_Type *base, uint64_t mask)
Disables FlexCAN Message Buffer interrupts.
This function disables the interrupts of given Message Buffers.
- Parameters:
base – FlexCAN peripheral base address.
mask – The ORed FlexCAN Message Buffer mask.
-
static inline void FLEXCAN_DisableHigh64MbInterrupts(CAN_Type *base, uint64_t mask)
Disables FlexCAN high 64 Message Buffer interrupts.
Valid only if the number of available MBs exceeds 64.
- Parameters:
base – FlexCAN peripheral base address.
mask – The ORed FlexCAN Message Buffer mask.
-
void FLEXCAN_EnableRxFifoDMA(CAN_Type *base, bool enable)
Enables or disables the FlexCAN Rx FIFO DMA request.
This function enables or disables the DMA feature of FlexCAN build-in Rx FIFO.
- Parameters:
base – FlexCAN peripheral base address.
enable – true to enable, false to disable.
-
static inline uintptr_t FLEXCAN_GetRxFifoHeadAddr(CAN_Type *base)
Gets the Rx FIFO Head address.
This function returns the FlexCAN Rx FIFO Head address, which is mainly used for the DMA/eDMA use case.
- Parameters:
base – FlexCAN peripheral base address.
- Returns:
FlexCAN Rx FIFO Head address.
-
static inline void FLEXCAN_Enable(CAN_Type *base, bool enable)
Enables or disables the FlexCAN module operation.
This function enables or disables the FlexCAN module.
- Parameters:
base – FlexCAN base pointer.
enable – true to enable, false to disable.
-
status_t FLEXCAN_WriteTxMb(CAN_Type *base, uint8_t mbIdx, const flexcan_frame_t *pTxFrame)
Writes a FlexCAN Message to the Transmit Message Buffer.
This function writes a CAN Message to the specified Transmit Message Buffer and changes the Message Buffer state to start CAN Message transmit. After that the function returns immediately.
- Parameters:
base – FlexCAN peripheral base address.
mbIdx – The FlexCAN Message Buffer index.
pTxFrame – Pointer to CAN message frame to be sent.
- Return values:
kStatus_Success – - Write Tx Message Buffer Successfully.
kStatus_Fail – - Tx Message Buffer is currently in use.
-
status_t FLEXCAN_ReadRxMb(CAN_Type *base, uint8_t mbIdx, flexcan_frame_t *pRxFrame)
Reads a FlexCAN Message from Receive Message Buffer.
This function reads a CAN message from a specified Receive Message Buffer. The function fills a receive CAN message frame structure with just received data and activates the Message Buffer again. The function returns immediately.
- Parameters:
base – FlexCAN peripheral base address.
mbIdx – The FlexCAN Message Buffer index.
pRxFrame – Pointer to CAN message frame structure for reception.
- Return values:
kStatus_Success – - Rx Message Buffer is full and has been read successfully.
kStatus_FLEXCAN_RxOverflow – - Rx Message Buffer is already overflowed and has been read successfully.
kStatus_Fail – - Rx Message Buffer is empty.
-
status_t FLEXCAN_WriteFDTxMb(CAN_Type *base, uint8_t mbIdx, const flexcan_fd_frame_t *pTxFrame)
Writes a FlexCAN FD Message to the Transmit Message Buffer.
This function writes a CAN FD Message to the specified Transmit Message Buffer and changes the Message Buffer state to start CAN FD Message transmit. After that the function returns immediately.
- Parameters:
base – FlexCAN peripheral base address.
mbIdx – The FlexCAN FD Message Buffer index.
pTxFrame – Pointer to CAN FD message frame to be sent.
- Return values:
kStatus_Success – - Write Tx Message Buffer Successfully.
kStatus_Fail – - Tx Message Buffer is currently in use.
-
status_t FLEXCAN_ReadFDRxMb(CAN_Type *base, uint8_t mbIdx, flexcan_fd_frame_t *pRxFrame)
Reads a FlexCAN FD Message from Receive Message Buffer.
This function reads a CAN FD message from a specified Receive Message Buffer. The function fills a receive CAN FD message frame structure with just received data and activates the Message Buffer again. The function returns immediately.
- Parameters:
base – FlexCAN peripheral base address.
mbIdx – The FlexCAN FD Message Buffer index.
pRxFrame – Pointer to CAN FD message frame structure for reception.
- Return values:
kStatus_Success – - Rx Message Buffer is full and has been read successfully.
kStatus_FLEXCAN_RxOverflow – - Rx Message Buffer is already overflowed and has been read successfully.
kStatus_Fail – - Rx Message Buffer is empty.
-
status_t FLEXCAN_ReadRxFifo(CAN_Type *base, flexcan_frame_t *pRxFrame)
Reads a FlexCAN Message from Legacy Rx FIFO.
This function reads a CAN message from the FlexCAN Legacy Rx FIFO.
- Parameters:
base – FlexCAN peripheral base address.
pRxFrame – Pointer to CAN message frame structure for reception.
- Return values:
kStatus_Success – - Read Message from Rx FIFO successfully.
kStatus_Fail – - Rx FIFO is not enabled.
-
status_t FLEXCAN_ReadPNWakeUpMB(CAN_Type *base, uint8_t mbIdx, flexcan_frame_t *pRxFrame)
Reads a FlexCAN Message from Wake Up MB.
This function reads a CAN message from the FlexCAN Wake up Message Buffers. There are four Wake up Message Buffers (WMBs) used to store incoming messages in Pretended Networking mode. The WMB index indicates the arrival order. The last message is stored in WMB3.
- Parameters:
base – FlexCAN peripheral base address.
pRxFrame – Pointer to CAN message frame structure for reception.
mbIdx – The FlexCAN Wake up Message Buffer index. Range in 0x0 ~ 0x3.
- Return values:
kStatus_Success – - Read Message from Wake up Message Buffer successfully.
kStatus_Fail – - Wake up Message Buffer has no valid content.
-
status_t FLEXCAN_TransferFDSendBlocking(CAN_Type *base, uint8_t mbIdx, flexcan_fd_frame_t *pTxFrame)
Performs a polling send transaction on the CAN bus.
Note
A transfer handle does not need to be created before calling this API.
- Parameters:
base – FlexCAN peripheral base pointer.
mbIdx – The FlexCAN FD Message Buffer index.
pTxFrame – Pointer to CAN FD message frame to be sent.
- Return values:
kStatus_Success – - Write Tx Message Buffer Successfully.
kStatus_Fail – - Tx Message Buffer is currently in use.
-
status_t FLEXCAN_TransferFDReceiveBlocking(CAN_Type *base, uint8_t mbIdx, flexcan_fd_frame_t *pRxFrame)
Performs a polling receive transaction on the CAN bus.
Note
A transfer handle does not need to be created before calling this API.
- Parameters:
base – FlexCAN peripheral base pointer.
mbIdx – The FlexCAN FD Message Buffer index.
pRxFrame – Pointer to CAN FD message frame structure for reception.
- Return values:
kStatus_Success – - Rx Message Buffer is full and has been read successfully.
kStatus_FLEXCAN_RxOverflow – - Rx Message Buffer is already overflowed and has been read successfully.
kStatus_Fail – - Rx Message Buffer is empty.
-
status_t FLEXCAN_TransferFDSendNonBlocking(CAN_Type *base, flexcan_handle_t *handle, flexcan_mb_transfer_t *pMbXfer)
Sends a message using IRQ.
This function sends a message using IRQ. This is a non-blocking function, which returns right away. When messages have been sent out, the send callback function is called.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
pMbXfer – FlexCAN FD Message Buffer transfer structure. See the flexcan_mb_transfer_t.
- Return values:
kStatus_Success – Start Tx Message Buffer sending process successfully.
kStatus_Fail – Write Tx Message Buffer failed.
kStatus_FLEXCAN_TxBusy – Tx Message Buffer is in use.
-
status_t FLEXCAN_TransferFDReceiveNonBlocking(CAN_Type *base, flexcan_handle_t *handle, flexcan_mb_transfer_t *pMbXfer)
Receives a message using IRQ.
This function receives a message using IRQ. This is non-blocking function, which returns right away. When the message has been received, the receive callback function is called.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
pMbXfer – FlexCAN FD Message Buffer transfer structure. See the flexcan_mb_transfer_t.
- Return values:
kStatus_Success – - Start Rx Message Buffer receiving process successfully.
kStatus_FLEXCAN_RxBusy – - Rx Message Buffer is in use.
-
void FLEXCAN_TransferFDAbortSend(CAN_Type *base, flexcan_handle_t *handle, uint8_t mbIdx)
Aborts the interrupt driven message send process.
This function aborts the interrupt driven message send process.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
mbIdx – The FlexCAN FD Message Buffer index.
-
void FLEXCAN_TransferFDAbortReceive(CAN_Type *base, flexcan_handle_t *handle, uint8_t mbIdx)
Aborts the interrupt driven message receive process.
This function aborts the interrupt driven message receive process.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
mbIdx – The FlexCAN FD Message Buffer index.
-
status_t FLEXCAN_TransferSendBlocking(CAN_Type *base, uint8_t mbIdx, flexcan_frame_t *pTxFrame)
Performs a polling send transaction on the CAN bus.
Note
A transfer handle does not need to be created before calling this API.
- Parameters:
base – FlexCAN peripheral base pointer.
mbIdx – The FlexCAN Message Buffer index.
pTxFrame – Pointer to CAN message frame to be sent.
- Return values:
kStatus_Success – - Write Tx Message Buffer Successfully.
kStatus_Fail – - Tx Message Buffer is currently in use.
-
status_t FLEXCAN_TransferReceiveBlocking(CAN_Type *base, uint8_t mbIdx, flexcan_frame_t *pRxFrame)
Performs a polling receive transaction on the CAN bus.
Note
A transfer handle does not need to be created before calling this API.
- Parameters:
base – FlexCAN peripheral base pointer.
mbIdx – The FlexCAN Message Buffer index.
pRxFrame – Pointer to CAN message frame structure for reception.
- Return values:
kStatus_Success – - Rx Message Buffer is full and has been read successfully.
kStatus_FLEXCAN_RxOverflow – - Rx Message Buffer is already overflowed and has been read successfully.
kStatus_Fail – - Rx Message Buffer is empty.
-
status_t FLEXCAN_TransferReceiveFifoBlocking(CAN_Type *base, flexcan_frame_t *pRxFrame)
Performs a polling receive transaction from Legacy Rx FIFO on the CAN bus.
Note
A transfer handle does not need to be created before calling this API.
- Parameters:
base – FlexCAN peripheral base pointer.
pRxFrame – Pointer to CAN message frame structure for reception.
- Return values:
kStatus_Success – - Read Message from Rx FIFO successfully.
kStatus_Fail – - Rx FIFO is not enabled.
-
void FLEXCAN_TransferCreateHandle(CAN_Type *base, flexcan_handle_t *handle, flexcan_transfer_callback_t callback, void *userData)
Initializes the FlexCAN handle.
This function initializes the FlexCAN handle, which can be used for other FlexCAN transactional APIs. Usually, for a specified FlexCAN instance, call this API once to get the initialized handle.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
callback – The callback function.
userData – The parameter of the callback function.
-
status_t FLEXCAN_TransferSendNonBlocking(CAN_Type *base, flexcan_handle_t *handle, flexcan_mb_transfer_t *pMbXfer)
Sends a message using IRQ.
This function sends a message using IRQ. This is a non-blocking function, which returns right away. When messages have been sent out, the send callback function is called.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
pMbXfer – FlexCAN Message Buffer transfer structure. See the flexcan_mb_transfer_t.
- Return values:
kStatus_Success – Start Tx Message Buffer sending process successfully.
kStatus_Fail – Write Tx Message Buffer failed.
kStatus_FLEXCAN_TxBusy – Tx Message Buffer is in use.
-
status_t FLEXCAN_TransferReceiveNonBlocking(CAN_Type *base, flexcan_handle_t *handle, flexcan_mb_transfer_t *pMbXfer)
Receives a message using IRQ.
This function receives a message using IRQ. This is non-blocking function, which returns right away. When the message has been received, the receive callback function is called.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
pMbXfer – FlexCAN Message Buffer transfer structure. See the flexcan_mb_transfer_t.
- Return values:
kStatus_Success – - Start Rx Message Buffer receiving process successfully.
kStatus_FLEXCAN_RxBusy – - Rx Message Buffer is in use.
-
status_t FLEXCAN_TransferReceiveFifoNonBlocking(CAN_Type *base, flexcan_handle_t *handle, flexcan_fifo_transfer_t *pFifoXfer)
Receives a message from Rx FIFO using IRQ.
This function receives a message using IRQ. This is a non-blocking function, which returns right away. When all messages have been received, the receive callback function is called.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
pFifoXfer – FlexCAN Rx FIFO transfer structure. See the flexcan_fifo_transfer_t.
- Return values:
kStatus_Success – - Start Rx FIFO receiving process successfully.
kStatus_FLEXCAN_RxFifoBusy – - Rx FIFO is currently in use.
-
status_t FLEXCAN_TransferGetReceiveFifoCount(CAN_Type *base, flexcan_handle_t *handle, size_t *count)
Gets the Legacy Rx Fifo transfer status during a interrupt non-blocking receive.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
count – Number of CAN messages receive so far by the non-blocking transaction.
- Return values:
kStatus_InvalidArgument – count is Invalid.
kStatus_Success – Successfully return the count.
-
uint32_t FLEXCAN_GetTimeStamp(flexcan_handle_t *handle, uint8_t mbIdx)
Gets the detail index of Mailbox’s Timestamp by handle.
Then function can only be used when calling non-blocking Data transfer (TX/RX) API, After TX/RX data transfer done (User can get the status by handler’s callback function), we can get the detail index of Mailbox’s timestamp by handle, Detail non-blocking data transfer API (TX/RX) contain. -FLEXCAN_TransferSendNonBlocking -FLEXCAN_TransferFDSendNonBlocking -FLEXCAN_TransferReceiveNonBlocking -FLEXCAN_TransferFDReceiveNonBlocking -FLEXCAN_TransferReceiveFifoNonBlocking
- Parameters:
handle – FlexCAN handle pointer.
mbIdx – The FlexCAN Message Buffer index.
- Return values:
the – index of mailbox ‘s timestamp stored in the handle.
-
void FLEXCAN_TransferAbortSend(CAN_Type *base, flexcan_handle_t *handle, uint8_t mbIdx)
Aborts the interrupt driven message send process.
This function aborts the interrupt driven message send process.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
mbIdx – The FlexCAN Message Buffer index.
-
void FLEXCAN_TransferAbortReceive(CAN_Type *base, flexcan_handle_t *handle, uint8_t mbIdx)
Aborts the interrupt driven message receive process.
This function aborts the interrupt driven message receive process.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
mbIdx – The FlexCAN Message Buffer index.
-
void FLEXCAN_TransferAbortReceiveFifo(CAN_Type *base, flexcan_handle_t *handle)
Aborts the interrupt driven message receive from Rx FIFO process.
This function aborts the interrupt driven message receive from Rx FIFO process.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
-
void FLEXCAN_TransferHandleIRQ(CAN_Type *base, flexcan_handle_t *handle)
FlexCAN IRQ handle function.
This function handles the FlexCAN Error, the Message Buffer, and the Rx FIFO IRQ request.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
-
FSL_FLEXCAN_DRIVER_VERSION
FlexCAN driver version.
FlexCAN transfer status.
Values:
-
enumerator kStatus_FLEXCAN_TxBusy
Tx Message Buffer is Busy.
-
enumerator kStatus_FLEXCAN_TxIdle
Tx Message Buffer is Idle.
-
enumerator kStatus_FLEXCAN_TxSwitchToRx
Remote Message is send out and Message buffer changed to Receive one.
-
enumerator kStatus_FLEXCAN_RxBusy
Rx Message Buffer is Busy.
-
enumerator kStatus_FLEXCAN_RxIdle
Rx Message Buffer is Idle.
-
enumerator kStatus_FLEXCAN_RxOverflow
Rx Message Buffer is Overflowed.
-
enumerator kStatus_FLEXCAN_RxFifoBusy
Rx Message FIFO is Busy.
-
enumerator kStatus_FLEXCAN_RxFifoIdle
Rx Message FIFO is Idle.
-
enumerator kStatus_FLEXCAN_RxFifoOverflow
Rx Message FIFO is overflowed.
-
enumerator kStatus_FLEXCAN_RxFifoWarning
Rx Message FIFO is almost overflowed.
-
enumerator kStatus_FLEXCAN_RxFifoDisabled
Rx Message FIFO is disabled during reading.
-
enumerator kStatus_FLEXCAN_ErrorStatus
FlexCAN Module Error and Status.
-
enumerator kStatus_FLEXCAN_WakeUp
FlexCAN is waken up from STOP mode.
-
enumerator kStatus_FLEXCAN_UnHandled
UnHadled Interrupt asserted.
-
enumerator kStatus_FLEXCAN_RxRemote
Rx Remote Message Received in Mail box.
-
enumerator kStatus_FLEXCAN_TxBusy
-
enum _flexcan_frame_format
FlexCAN frame format.
Values:
-
enumerator kFLEXCAN_FrameFormatStandard
Standard frame format attribute.
-
enumerator kFLEXCAN_FrameFormatExtend
Extend frame format attribute.
-
enumerator kFLEXCAN_FrameFormatStandard
-
enum _flexcan_frame_type
FlexCAN frame type.
Values:
-
enumerator kFLEXCAN_FrameTypeData
Data frame type attribute.
-
enumerator kFLEXCAN_FrameTypeRemote
Remote frame type attribute.
-
enumerator kFLEXCAN_FrameTypeData
-
enum _flexcan_clock_source
FlexCAN clock source.
- Deprecated:
Do not use the kFLEXCAN_ClkSrcOs. It has been superceded kFLEXCAN_ClkSrc0
Do not use the kFLEXCAN_ClkSrcPeri. It has been superceded kFLEXCAN_ClkSrc1
Values:
-
enumerator kFLEXCAN_ClkSrcOsc
FlexCAN Protocol Engine clock from Oscillator.
-
enumerator kFLEXCAN_ClkSrcPeri
FlexCAN Protocol Engine clock from Peripheral Clock.
-
enumerator kFLEXCAN_ClkSrc0
FlexCAN Protocol Engine clock selected by user as SRC == 0.
-
enumerator kFLEXCAN_ClkSrc1
FlexCAN Protocol Engine clock selected by user as SRC == 1.
-
enum _flexcan_wake_up_source
FlexCAN wake up source.
Values:
-
enumerator kFLEXCAN_WakeupSrcUnfiltered
FlexCAN uses unfiltered Rx input to detect edge.
-
enumerator kFLEXCAN_WakeupSrcFiltered
FlexCAN uses filtered Rx input to detect edge.
-
enumerator kFLEXCAN_WakeupSrcUnfiltered
-
enum _flexcan_rx_fifo_filter_type
FlexCAN Rx Fifo Filter type.
Values:
-
enumerator kFLEXCAN_RxFifoFilterTypeA
One full ID (standard and extended) per ID Filter element.
-
enumerator kFLEXCAN_RxFifoFilterTypeB
Two full standard IDs or two partial 14-bit ID slices per ID Filter Table element.
-
enumerator kFLEXCAN_RxFifoFilterTypeC
Four partial 8-bit Standard or extended ID slices per ID Filter Table element.
-
enumerator kFLEXCAN_RxFifoFilterTypeD
All frames rejected.
-
enumerator kFLEXCAN_RxFifoFilterTypeA
-
enum _flexcan_mb_size
FlexCAN Message Buffer Payload size.
Values:
-
enumerator kFLEXCAN_8BperMB
Selects 8 bytes per Message Buffer.
-
enumerator kFLEXCAN_16BperMB
Selects 16 bytes per Message Buffer.
-
enumerator kFLEXCAN_32BperMB
Selects 32 bytes per Message Buffer.
-
enumerator kFLEXCAN_64BperMB
Selects 64 bytes per Message Buffer.
-
enumerator kFLEXCAN_8BperMB
-
enum _flexcan_fd_frame_length
FlexCAN CAN FD frame supporting data length (available DLC values).
For Tx, when the Data size corresponding to DLC value stored in the MB selected for transmission is larger than the MB Payload size, FlexCAN adds the necessary number of bytes with constant 0xCC pattern to complete the expected DLC. For Rx, when the Data size corresponding to DLC value received from the CAN bus is larger than the MB Payload size, the high order bytes that do not fit the Payload size will lose.
Values:
-
enumerator kFLEXCAN_0BperFrame
Frame contains 0 valid data bytes.
-
enumerator kFLEXCAN_1BperFrame
Frame contains 1 valid data bytes.
-
enumerator kFLEXCAN_2BperFrame
Frame contains 2 valid data bytes.
-
enumerator kFLEXCAN_3BperFrame
Frame contains 3 valid data bytes.
-
enumerator kFLEXCAN_4BperFrame
Frame contains 4 valid data bytes.
-
enumerator kFLEXCAN_5BperFrame
Frame contains 5 valid data bytes.
-
enumerator kFLEXCAN_6BperFrame
Frame contains 6 valid data bytes.
-
enumerator kFLEXCAN_7BperFrame
Frame contains 7 valid data bytes.
-
enumerator kFLEXCAN_8BperFrame
Frame contains 8 valid data bytes.
-
enumerator kFLEXCAN_12BperFrame
Frame contains 12 valid data bytes.
-
enumerator kFLEXCAN_16BperFrame
Frame contains 16 valid data bytes.
-
enumerator kFLEXCAN_20BperFrame
Frame contains 20 valid data bytes.
-
enumerator kFLEXCAN_24BperFrame
Frame contains 24 valid data bytes.
-
enumerator kFLEXCAN_32BperFrame
Frame contains 32 valid data bytes.
-
enumerator kFLEXCAN_48BperFrame
Frame contains 48 valid data bytes.
-
enumerator kFLEXCAN_64BperFrame
Frame contains 64 valid data bytes.
-
enumerator kFLEXCAN_0BperFrame
-
enum _flexcan_rx_fifo_priority
FlexCAN Enhanced/Legacy Rx FIFO priority.
The matching process starts from the Rx MB(or Enhanced/Legacy Rx FIFO) with higher priority. If no MB(or Enhanced/Legacy Rx FIFO filter) is satisfied, the matching process goes on with the Enhanced/Legacy Rx FIFO(or Rx MB) with lower priority.
Values:
-
enumerator kFLEXCAN_RxFifoPrioLow
Matching process start from Rx Message Buffer first.
-
enumerator kFLEXCAN_RxFifoPrioHigh
Matching process start from Enhanced/Legacy Rx FIFO first.
-
enumerator kFLEXCAN_RxFifoPrioLow
-
enum _flexcan_interrupt_enable
FlexCAN interrupt enable enumerations.
This provides constants for the FlexCAN interrupt enable enumerations for use in the FlexCAN functions.
Note
FlexCAN Message Buffers and Legacy Rx FIFO interrupts not included in.
Values:
-
enumerator kFLEXCAN_BusOffInterruptEnable
Bus Off interrupt, use bit 15.
-
enumerator kFLEXCAN_ErrorInterruptEnable
CAN Error interrupt, use bit 14.
-
enumerator kFLEXCAN_TxWarningInterruptEnable
Tx Warning interrupt, use bit 11.
-
enumerator kFLEXCAN_RxWarningInterruptEnable
Rx Warning interrupt, use bit 10.
-
enumerator kFLEXCAN_WakeUpInterruptEnable
Self Wake Up interrupt, use bit 26.
-
enumerator kFLEXCAN_FDErrorInterruptEnable
CAN FD Error interrupt, use bit 31.
-
enumerator kFLEXCAN_PNMatchWakeUpInterruptEnable
PN Match Wake Up interrupt, use high word bit 17.
-
enumerator kFLEXCAN_PNTimeoutWakeUpInterruptEnable
PN Timeout Wake Up interrupt, use high word bit 16.
-
enumerator kFLEXCAN_HostAccessNCErrorInterruptEnable
Host Access With Non-Correctable Errors interrupt, use high word bit 0.
-
enumerator kFLEXCAN_FlexCanAccessNCErrorInterruptEnable
FlexCAN Access With Non-Correctable Errors interrupt, use high word bit 2.
-
enumerator kFLEXCAN_HostOrFlexCanCErrorInterruptEnable
Host or FlexCAN Access With Correctable Errors interrupt, use high word bit 3.
-
enumerator kFLEXCAN_BusOffInterruptEnable
-
enum _flexcan_flags
FlexCAN status flags.
This provides constants for the FlexCAN status flags for use in the FlexCAN functions.
Note
The CPU read action clears the bits corresponding to the FlEXCAN_ErrorFlag macro, therefore user need to read status flags and distinguish which error is occur using _flexcan_error_flags enumerations.
Values:
-
enumerator kFLEXCAN_ErrorOverrunFlag
Error Overrun Status.
-
enumerator kFLEXCAN_FDErrorIntFlag
CAN FD Error Interrupt Flag.
-
enumerator kFLEXCAN_BusoffDoneIntFlag
Bus Off process completed Interrupt Flag.
-
enumerator kFLEXCAN_SynchFlag
CAN Synchronization Status.
-
enumerator kFLEXCAN_TxWarningIntFlag
Tx Warning Interrupt Flag.
-
enumerator kFLEXCAN_RxWarningIntFlag
Rx Warning Interrupt Flag.
-
enumerator kFLEXCAN_IdleFlag
FlexCAN In IDLE Status.
-
enumerator kFLEXCAN_FaultConfinementFlag
FlexCAN Fault Confinement State.
-
enumerator kFLEXCAN_TransmittingFlag
FlexCAN In Transmission Status.
-
enumerator kFLEXCAN_ReceivingFlag
FlexCAN In Reception Status.
-
enumerator kFLEXCAN_BusOffIntFlag
Bus Off Interrupt Flag.
-
enumerator kFLEXCAN_ErrorIntFlag
CAN Error Interrupt Flag.
-
enumerator kFLEXCAN_WakeUpIntFlag
Self Wake-Up Interrupt Flag.
-
enumerator kFLEXCAN_ErrorFlag
-
enumerator kFLEXCAN_PNMatchIntFlag
PN Matching Event Interrupt Flag.
-
enumerator kFLEXCAN_PNTimeoutIntFlag
PN Timeout Event Interrupt Flag.
-
enumerator kFLEXCAN_HostAccessNonCorrectableErrorIntFlag
Host Access With Non-Correctable Error Interrupt Flag.
-
enumerator kFLEXCAN_FlexCanAccessNonCorrectableErrorIntFlag
FlexCAN Access With Non-Correctable Error Interrupt Flag.
-
enumerator kFLEXCAN_CorrectableErrorIntFlag
Correctable Error Interrupt Flag.
-
enumerator kFLEXCAN_HostAccessNonCorrectableErrorOverrunFlag
Host Access With Non-Correctable Error Interrupt Overrun Flag.
-
enumerator kFLEXCAN_FlexCanAccessNonCorrectableErrorOverrunFlag
FlexCAN Access With Non-Correctable Error Interrupt Overrun Flag.
-
enumerator kFLEXCAN_CorrectableErrorOverrunFlag
Correctable Error Interrupt Overrun Flag.
-
enumerator kFLEXCAN_AllMemoryErrorFlag
All Memory Error Flags.
-
enumerator kFLEXCAN_ErrorOverrunFlag
-
enum _flexcan_error_flags
FlexCAN error status flags.
The FlexCAN Error Status enumerations is used to report current error of the FlexCAN bus. This enumerations should be used with KFLEXCAN_ErrorFlag in _flexcan_flags enumerations to ditermine which error is generated.
Values:
-
enumerator kFLEXCAN_FDStuffingError
Stuffing Error.
-
enumerator kFLEXCAN_FDFormError
Form Error.
-
enumerator kFLEXCAN_FDCrcError
Cyclic Redundancy Check Error.
-
enumerator kFLEXCAN_FDBit0Error
Unable to send dominant bit.
-
enumerator kFLEXCAN_FDBit1Error
Unable to send recessive bit.
-
enumerator kFLEXCAN_TxErrorWarningFlag
Tx Error Warning Status.
-
enumerator kFLEXCAN_RxErrorWarningFlag
Rx Error Warning Status.
-
enumerator kFLEXCAN_StuffingError
Stuffing Error.
-
enumerator kFLEXCAN_FormError
Form Error.
-
enumerator kFLEXCAN_CrcError
Cyclic Redundancy Check Error.
-
enumerator kFLEXCAN_AckError
Received no ACK on transmission.
-
enumerator kFLEXCAN_Bit0Error
Unable to send dominant bit.
-
enumerator kFLEXCAN_Bit1Error
Unable to send recessive bit.
-
enumerator kFLEXCAN_FDStuffingError
FlexCAN Legacy Rx FIFO status flags.
The FlexCAN Legacy Rx FIFO Status enumerations are used to determine the status of the Rx FIFO. Because Rx FIFO occupy the MB0 ~ MB7 (Rx Fifo filter also occupies more Message Buffer space), Rx FIFO status flags are mapped to the corresponding Message Buffer status flags.
Values:
-
enumerator kFLEXCAN_RxFifoOverflowFlag
Rx FIFO overflow flag.
-
enumerator kFLEXCAN_RxFifoWarningFlag
Rx FIFO almost full flag.
-
enumerator kFLEXCAN_RxFifoFrameAvlFlag
Frames available in Rx FIFO flag.
-
enumerator kFLEXCAN_RxFifoOverflowFlag
-
enum _flexcan_memory_error_type
FlexCAN Memory Error Type.
Values:
-
enumerator kFLEXCAN_CorrectableError
The memory error is correctable which means on bit error.
-
enumerator kFLEXCAN_NonCorrectableError
The memory error is non-correctable which means two bit errors.
-
enumerator kFLEXCAN_CorrectableError
-
enum _flexcan_memory_access_type
FlexCAN Memory Access Type.
Values:
-
enumerator kFLEXCAN_MoveOutFlexCanAccess
The memory error was detected during move-out FlexCAN access.
-
enumerator kFLEXCAN_MoveInAccess
The memory error was detected during move-in FlexCAN access.
-
enumerator kFLEXCAN_TxArbitrationAccess
The memory error was detected during Tx Arbitration FlexCAN access.
-
enumerator kFLEXCAN_RxMatchingAccess
The memory error was detected during Rx Matching FlexCAN access.
-
enumerator kFLEXCAN_MoveOutHostAccess
The memory error was detected during Rx Matching Host (CPU) access.
-
enumerator kFLEXCAN_MoveOutFlexCanAccess
-
enum _flexcan_byte_error_syndrome
FlexCAN Memory Error Byte Syndrome.
Values:
-
enumerator kFLEXCAN_NoError
No bit error in this byte.
-
enumerator kFLEXCAN_ParityBits0Error
Parity bit 0 error in this byte.
-
enumerator kFLEXCAN_ParityBits1Error
Parity bit 1 error in this byte.
-
enumerator kFLEXCAN_ParityBits2Error
Parity bit 2 error in this byte.
-
enumerator kFLEXCAN_ParityBits3Error
Parity bit 3 error in this byte.
-
enumerator kFLEXCAN_ParityBits4Error
Parity bit 4 error in this byte.
-
enumerator kFLEXCAN_DataBits0Error
Data bit 0 error in this byte.
-
enumerator kFLEXCAN_DataBits1Error
Data bit 1 error in this byte.
-
enumerator kFLEXCAN_DataBits2Error
Data bit 2 error in this byte.
-
enumerator kFLEXCAN_DataBits3Error
Data bit 3 error in this byte.
-
enumerator kFLEXCAN_DataBits4Error
Data bit 4 error in this byte.
-
enumerator kFLEXCAN_DataBits5Error
Data bit 5 error in this byte.
-
enumerator kFLEXCAN_DataBits6Error
Data bit 6 error in this byte.
-
enumerator kFLEXCAN_DataBits7Error
Data bit 7 error in this byte.
-
enumerator kFLEXCAN_AllZeroError
All-zeros non-correctable error in this byte.
-
enumerator kFLEXCAN_AllOneError
All-ones non-correctable error in this byte.
-
enumerator kFLEXCAN_NonCorrectableErrors
Non-correctable error in this byte.
-
enumerator kFLEXCAN_NoError
-
enum _flexcan_pn_match_source
FlexCAN Pretended Networking match source selection.
Values:
-
enumerator kFLEXCAN_PNMatSrcID
Message match with ID filtering.
-
enumerator kFLEXCAN_PNMatSrcIDAndData
Message match with ID filtering and payload filtering.
-
enumerator kFLEXCAN_PNMatSrcID
-
enum _flexcan_pn_match_mode
FlexCAN Pretended Networking mode match type.
Values:
-
enumerator kFLEXCAN_PNMatModeEqual
Match upon ID/Payload contents against an exact target value.
-
enumerator kFLEXCAN_PNMatModeGreater
Match upon an ID/Payload value greater than or equal to a specified target value.
-
enumerator kFLEXCAN_PNMatModeSmaller
Match upon an ID/Payload value smaller than or equal to a specified target value.
-
enumerator kFLEXCAN_PNMatModeRange
Match upon an ID/Payload value inside a range, greater than or equal to a specified lower limit, and smaller than or equal to a specified upper limit
-
enumerator kFLEXCAN_PNMatModeEqual
-
typedef enum _flexcan_frame_format flexcan_frame_format_t
FlexCAN frame format.
-
typedef enum _flexcan_frame_type flexcan_frame_type_t
FlexCAN frame type.
-
typedef enum _flexcan_clock_source flexcan_clock_source_t
FlexCAN clock source.
- Deprecated:
Do not use the kFLEXCAN_ClkSrcOs. It has been superceded kFLEXCAN_ClkSrc0
Do not use the kFLEXCAN_ClkSrcPeri. It has been superceded kFLEXCAN_ClkSrc1
-
typedef enum _flexcan_wake_up_source flexcan_wake_up_source_t
FlexCAN wake up source.
-
typedef enum _flexcan_rx_fifo_filter_type flexcan_rx_fifo_filter_type_t
FlexCAN Rx Fifo Filter type.
-
typedef enum _flexcan_mb_size flexcan_mb_size_t
FlexCAN Message Buffer Payload size.
-
typedef enum _flexcan_rx_fifo_priority flexcan_rx_fifo_priority_t
FlexCAN Enhanced/Legacy Rx FIFO priority.
The matching process starts from the Rx MB(or Enhanced/Legacy Rx FIFO) with higher priority. If no MB(or Enhanced/Legacy Rx FIFO filter) is satisfied, the matching process goes on with the Enhanced/Legacy Rx FIFO(or Rx MB) with lower priority.
-
typedef enum _flexcan_memory_error_type flexcan_memory_error_type_t
FlexCAN Memory Error Type.
-
typedef enum _flexcan_memory_access_type flexcan_memory_access_type_t
FlexCAN Memory Access Type.
-
typedef enum _flexcan_byte_error_syndrome flexcan_byte_error_syndrome_t
FlexCAN Memory Error Byte Syndrome.
-
typedef struct _flexcan_memory_error_report_status flexcan_memory_error_report_status_t
FlexCAN memory error register status structure.
This structure contains the memory access properties that caused a memory error access. It is used as the parameter of FLEXCAN_GetMemoryErrorReportStatus() function. And user can use FLEXCAN_GetMemoryErrorReportStatus to get the status of the last memory error access.
-
typedef struct _flexcan_frame flexcan_frame_t
FlexCAN message frame structure.
-
typedef struct _flexcan_fd_frame flexcan_fd_frame_t
CAN FD message frame structure.
The CAN FD message supporting up to sixty four bytes can be used for a data frame, depending on the length selected for the message buffers. The length should be a enumeration member, see _flexcan_fd_frame_length.
-
typedef struct _flexcan_timing_config flexcan_timing_config_t
FlexCAN protocol timing characteristic configuration structure.
-
typedef struct _flexcan_config flexcan_config_t
FlexCAN module configuration structure.
- Deprecated:
Do not use the baudRate. It has been superceded bitRate
Do not use the baudRateFD. It has been superceded bitRateFD
-
typedef struct _flexcan_rx_mb_config flexcan_rx_mb_config_t
FlexCAN Receive Message Buffer configuration structure.
This structure is used as the parameter of FLEXCAN_SetRxMbConfig() function. The FLEXCAN_SetRxMbConfig() function is used to configure FlexCAN Receive Message Buffer. The function abort previous receiving process, clean the Message Buffer and activate the Rx Message Buffer using given Message Buffer setting.
-
typedef enum _flexcan_pn_match_source flexcan_pn_match_source_t
FlexCAN Pretended Networking match source selection.
-
typedef enum _flexcan_pn_match_mode flexcan_pn_match_mode_t
FlexCAN Pretended Networking mode match type.
-
typedef struct _flexcan_pn_config flexcan_pn_config_t
FlexCAN Pretended Networking configuration structure.
This structure is used as the parameter of FLEXCAN_SetPNConfig() function. The FLEXCAN_SetPNConfig() function is used to configure FlexCAN Networking work mode.
-
typedef struct _flexcan_rx_fifo_config flexcan_rx_fifo_config_t
FlexCAN Legacy Rx FIFO configuration structure.
-
typedef struct _flexcan_mb_transfer flexcan_mb_transfer_t
FlexCAN Message Buffer transfer.
-
typedef struct _flexcan_fifo_transfer flexcan_fifo_transfer_t
FlexCAN Rx FIFO transfer.
-
typedef struct _flexcan_handle flexcan_handle_t
FlexCAN handle structure definition.
-
typedef void (*flexcan_transfer_callback_t)(CAN_Type *base, flexcan_handle_t *handle, status_t status, uint64_t result, void *userData)
-
FLEXCAN_WAIT_TIMEOUT
-
DLC_LENGTH_DECODE(dlc)
FlexCAN frame length helper macro.
-
FLEXCAN_ID_STD(id)
FlexCAN Frame ID helper macro.
Standard Frame ID helper macro.
-
FLEXCAN_ID_EXT(id)
Extend Frame ID helper macro.
-
FLEXCAN_RX_MB_STD_MASK(id, rtr, ide)
FlexCAN Rx Message Buffer Mask helper macro.
Standard Rx Message Buffer Mask helper macro.
-
FLEXCAN_RX_MB_EXT_MASK(id, rtr, ide)
Extend Rx Message Buffer Mask helper macro.
-
FLEXCAN_RX_FIFO_STD_MASK_TYPE_A(id, rtr, ide)
FlexCAN Legacy Rx FIFO Mask helper macro.
Standard Rx FIFO Mask helper macro Type A helper macro.
-
FLEXCAN_RX_FIFO_STD_MASK_TYPE_B_HIGH(id, rtr, ide)
Standard Rx FIFO Mask helper macro Type B upper part helper macro.
-
FLEXCAN_RX_FIFO_STD_MASK_TYPE_B_LOW(id, rtr, ide)
Standard Rx FIFO Mask helper macro Type B lower part helper macro.
-
FLEXCAN_RX_FIFO_STD_MASK_TYPE_C_HIGH(id)
Standard Rx FIFO Mask helper macro Type C upper part helper macro.
-
FLEXCAN_RX_FIFO_STD_MASK_TYPE_C_MID_HIGH(id)
Standard Rx FIFO Mask helper macro Type C mid-upper part helper macro.
-
FLEXCAN_RX_FIFO_STD_MASK_TYPE_C_MID_LOW(id)
Standard Rx FIFO Mask helper macro Type C mid-lower part helper macro.
-
FLEXCAN_RX_FIFO_STD_MASK_TYPE_C_LOW(id)
Standard Rx FIFO Mask helper macro Type C lower part helper macro.
-
FLEXCAN_RX_FIFO_EXT_MASK_TYPE_A(id, rtr, ide)
Extend Rx FIFO Mask helper macro Type A helper macro.
-
FLEXCAN_RX_FIFO_EXT_MASK_TYPE_B_HIGH(id, rtr, ide)
Extend Rx FIFO Mask helper macro Type B upper part helper macro.
-
FLEXCAN_RX_FIFO_EXT_MASK_TYPE_B_LOW(id, rtr, ide)
Extend Rx FIFO Mask helper macro Type B lower part helper macro.
-
FLEXCAN_RX_FIFO_EXT_MASK_TYPE_C_HIGH(id)
Extend Rx FIFO Mask helper macro Type C upper part helper macro.
-
FLEXCAN_RX_FIFO_EXT_MASK_TYPE_C_MID_HIGH(id)
Extend Rx FIFO Mask helper macro Type C mid-upper part helper macro.
-
FLEXCAN_RX_FIFO_EXT_MASK_TYPE_C_MID_LOW(id)
Extend Rx FIFO Mask helper macro Type C mid-lower part helper macro.
-
FLEXCAN_RX_FIFO_EXT_MASK_TYPE_C_LOW(id)
Extend Rx FIFO Mask helper macro Type C lower part helper macro.
-
FLEXCAN_RX_FIFO_STD_FILTER_TYPE_A(id, rtr, ide)
FlexCAN Rx FIFO Filter helper macro.
Standard Rx FIFO Filter helper macro Type A helper macro.
-
FLEXCAN_RX_FIFO_STD_FILTER_TYPE_B_HIGH(id, rtr, ide)
Standard Rx FIFO Filter helper macro Type B upper part helper macro.
-
FLEXCAN_RX_FIFO_STD_FILTER_TYPE_B_LOW(id, rtr, ide)
Standard Rx FIFO Filter helper macro Type B lower part helper macro.
-
FLEXCAN_RX_FIFO_STD_FILTER_TYPE_C_HIGH(id)
Standard Rx FIFO Filter helper macro Type C upper part helper macro.
-
FLEXCAN_RX_FIFO_STD_FILTER_TYPE_C_MID_HIGH(id)
Standard Rx FIFO Filter helper macro Type C mid-upper part helper macro.
-
FLEXCAN_RX_FIFO_STD_FILTER_TYPE_C_MID_LOW(id)
Standard Rx FIFO Filter helper macro Type C mid-lower part helper macro.
-
FLEXCAN_RX_FIFO_STD_FILTER_TYPE_C_LOW(id)
Standard Rx FIFO Filter helper macro Type C lower part helper macro.
-
FLEXCAN_RX_FIFO_EXT_FILTER_TYPE_A(id, rtr, ide)
Extend Rx FIFO Filter helper macro Type A helper macro.
-
FLEXCAN_RX_FIFO_EXT_FILTER_TYPE_B_HIGH(id, rtr, ide)
Extend Rx FIFO Filter helper macro Type B upper part helper macro.
-
FLEXCAN_RX_FIFO_EXT_FILTER_TYPE_B_LOW(id, rtr, ide)
Extend Rx FIFO Filter helper macro Type B lower part helper macro.
-
FLEXCAN_RX_FIFO_EXT_FILTER_TYPE_C_HIGH(id)
Extend Rx FIFO Filter helper macro Type C upper part helper macro.
-
FLEXCAN_RX_FIFO_EXT_FILTER_TYPE_C_MID_HIGH(id)
Extend Rx FIFO Filter helper macro Type C mid-upper part helper macro.
-
FLEXCAN_RX_FIFO_EXT_FILTER_TYPE_C_MID_LOW(id)
Extend Rx FIFO Filter helper macro Type C mid-lower part helper macro.
-
FLEXCAN_RX_FIFO_EXT_FILTER_TYPE_C_LOW(id)
Extend Rx FIFO Filter helper macro Type C lower part helper macro.
-
FLEXCAN_PN_STD_MASK(id, rtr)
FlexCAN Pretended Networking ID Mask helper macro.
Standard Rx Message Buffer Mask helper macro.
-
FLEXCAN_PN_EXT_MASK(id, rtr)
Extend Rx Message Buffer Mask helper macro.
-
FLEXCAN_PN_INT_MASK(x)
FlexCAN interrupt/status flag helper macro.
-
FLEXCAN_PN_INT_UNMASK(x)
-
FLEXCAN_PN_STATUS_MASK(x)
-
FLEXCAN_PN_STATUS_UNMASK(x)
-
FLEXCAN_MECR_INT_MASK(x)
-
FLEXCAN_MECR_INT_UNMASK(x)
-
FLEXCAN_MECR_STATUS_MASK(x)
-
FLEXCAN_MECR_STATUS_UNMASK(x)
-
FLEXCAN_ERROR_AND_STATUS_INIT_FLAG
-
FLEXCAN_WAKE_UP_FLAG
-
FLEXCAN_MEMORY_ERROR_INIT_FLAG
-
FLEXCAN_MEMORY_ENHANCED_RX_FIFO_INIT_FLAG
FlexCAN Enhanced Rx FIFO base address helper macro.
-
FLEXCAN_CALLBACK(x)
FlexCAN transfer callback function.
The FlexCAN transfer callback returns a value from the underlying layer. If the status equals to kStatus_FLEXCAN_ErrorStatus, the result parameter is the Content of FlexCAN status register which can be used to get the working status(or error status) of FlexCAN module. If the status equals to other FlexCAN Message Buffer transfer status, the result is the index of Message Buffer that generate transfer event. If the status equals to other FlexCAN Message Buffer transfer status, the result is meaningless and should be Ignored.
-
struct _flexcan_memory_error_report_status
- #include <fsl_flexcan.h>
FlexCAN memory error register status structure.
This structure contains the memory access properties that caused a memory error access. It is used as the parameter of FLEXCAN_GetMemoryErrorReportStatus() function. And user can use FLEXCAN_GetMemoryErrorReportStatus to get the status of the last memory error access.
Public Members
-
flexcan_memory_error_type_t errorType
The type of memory error that giving rise to the report.
-
flexcan_memory_access_type_t accessType
The type of memory access that giving rise to the memory error.
-
uint16_t accessAddress
The address where memory error detected.
-
uint32_t errorData
The raw data word read from memory with error.
-
flexcan_memory_error_type_t errorType
-
struct _flexcan_frame
- #include <fsl_flexcan.h>
FlexCAN message frame structure.
-
struct _flexcan_fd_frame
- #include <fsl_flexcan.h>
CAN FD message frame structure.
The CAN FD message supporting up to sixty four bytes can be used for a data frame, depending on the length selected for the message buffers. The length should be a enumeration member, see _flexcan_fd_frame_length.
-
struct _flexcan_timing_config
- #include <fsl_flexcan.h>
FlexCAN protocol timing characteristic configuration structure.
Public Members
-
uint16_t preDivider
Classic CAN or CAN FD nominal phase bit rate prescaler.
-
uint8_t rJumpwidth
Classic CAN or CAN FD nominal phase Re-sync Jump Width.
-
uint8_t phaseSeg1
Classic CAN or CAN FD nominal phase Segment 1.
-
uint8_t phaseSeg2
Classic CAN or CAN FD nominal phase Segment 2.
-
uint8_t propSeg
Classic CAN or CAN FD nominal phase Propagation Segment.
-
uint16_t fpreDivider
CAN FD data phase bit rate prescaler.
-
uint8_t frJumpwidth
CAN FD data phase Re-sync Jump Width.
-
uint8_t fphaseSeg1
CAN FD data phase Phase Segment 1.
-
uint8_t fphaseSeg2
CAN FD data phase Phase Segment 2.
-
uint8_t fpropSeg
CAN FD data phase Propagation Segment.
-
uint16_t preDivider
-
struct _flexcan_config
- #include <fsl_flexcan.h>
FlexCAN module configuration structure.
- Deprecated:
Do not use the baudRate. It has been superceded bitRate
Do not use the baudRateFD. It has been superceded bitRateFD
Public Members
-
flexcan_clock_source_t clkSrc
Clock source for FlexCAN Protocol Engine.
-
flexcan_wake_up_source_t wakeupSrc
Wake up source selection.
-
uint8_t maxMbNum
The maximum number of Message Buffers used by user.
-
bool enableLoopBack
Enable or Disable Loop Back Self Test Mode.
-
bool enableTimerSync
Enable or Disable Timer Synchronization.
-
bool enableSelfWakeup
Enable or Disable Self Wakeup Mode.
-
bool enableIndividMask
Enable or Disable Rx Individual Mask and Queue feature.
-
bool disableSelfReception
Enable or Disable Self Reflection.
-
bool enableListenOnlyMode
Enable or Disable Listen Only Mode.
-
bool enableDoze
Enable or Disable Doze Mode.
-
bool enablePretendedeNetworking
Enable or Disable the Pretended Networking mode.
-
bool enableMemoryErrorControl
Enable or Disable the memory errors detection and correction mechanism.
-
bool enableNonCorrectableErrorEnterFreeze
Enable or Disable Non-Correctable Errors In FlexCAN Access Put Device In Freeze Mode.
-
bool enableTransceiverDelayMeasure
Enable or Disable the transceiver delay measurement, when it is enabled, then the secondary sample point position is determined by the sum of the transceiver delay measurement plus the enhanced TDC offset.
-
bool enableRemoteRequestFrameStored
true: Store Remote Request Frame in the same fashion of data frame. false: Generate an automatic Remote Response Frame.
-
struct _flexcan_rx_mb_config
- #include <fsl_flexcan.h>
FlexCAN Receive Message Buffer configuration structure.
This structure is used as the parameter of FLEXCAN_SetRxMbConfig() function. The FLEXCAN_SetRxMbConfig() function is used to configure FlexCAN Receive Message Buffer. The function abort previous receiving process, clean the Message Buffer and activate the Rx Message Buffer using given Message Buffer setting.
Public Members
-
uint32_t id
CAN Message Buffer Frame Identifier, should be set using FLEXCAN_ID_EXT() or FLEXCAN_ID_STD() macro.
-
flexcan_frame_format_t format
CAN Frame Identifier format(Standard of Extend).
-
flexcan_frame_type_t type
CAN Frame Type(Data or Remote).
-
uint32_t id
-
struct _flexcan_pn_config
- #include <fsl_flexcan.h>
FlexCAN Pretended Networking configuration structure.
This structure is used as the parameter of FLEXCAN_SetPNConfig() function. The FLEXCAN_SetPNConfig() function is used to configure FlexCAN Networking work mode.
Public Members
-
bool enableTimeout
Enable or Disable timeout event trigger wakeup.
-
uint16_t timeoutValue
The timeout value that generates a wakeup event, the counter timer is incremented based on 64 times the CAN Bit Time unit.
-
bool enableMatch
Enable or Disable match event trigger wakeup.
-
flexcan_pn_match_source_t matchSrc
Selects the match source (ID and/or data match) to trigger wakeup.
-
uint8_t matchNum
The number of times a given message must match the predefined ID and/or data before generating a wakeup event, range in 0x1 ~ 0xFF.
-
flexcan_pn_match_mode_t idMatchMode
The ID match type.
-
flexcan_pn_match_mode_t dataMatchMode
The data match type.
-
uint32_t idLower
The ID target values 1 which used either for ID match “equal to”, “smaller than”, “greater than” comparisons, or as the lower limit value in ID match “range detection”.
-
uint32_t idUpper
The ID target values 2 which used only as the upper limit value in ID match “range
detection” or used to store the ID mask in “equal to”.
-
uint8_t lengthLower
The lower limit for length of data bytes which used only in data match “range
detection”. Range in 0x0 ~ 0x8.
-
uint8_t lengthUpper
The upper limit for length of data bytes which used only in data match “range
detection”. Range in 0x0 ~ 0x8.
-
bool enableTimeout
-
struct _flexcan_rx_fifo_config
- #include <fsl_flexcan.h>
FlexCAN Legacy Rx FIFO configuration structure.
Public Members
-
uint32_t *idFilterTable
Pointer to the FlexCAN Legacy Rx FIFO identifier filter table.
-
uint8_t idFilterNum
The FlexCAN Legacy Rx FIFO Filter elements quantity.
-
flexcan_rx_fifo_filter_type_t idFilterType
The FlexCAN Legacy Rx FIFO Filter type.
-
flexcan_rx_fifo_priority_t priority
The FlexCAN Legacy Rx FIFO receive priority.
-
uint32_t *idFilterTable
-
struct _flexcan_mb_transfer
- #include <fsl_flexcan.h>
FlexCAN Message Buffer transfer.
Public Members
-
flexcan_frame_t *frame
The buffer of CAN Message to be transfer.
-
uint8_t mbIdx
The index of Message buffer used to transfer Message.
-
flexcan_frame_t *frame
-
struct _flexcan_fifo_transfer
- #include <fsl_flexcan.h>
FlexCAN Rx FIFO transfer.
Public Members
-
flexcan_frame_t *frame
The buffer of CAN Message to be received from Legacy Rx FIFO.
-
size_t frameNum
Number of CAN Message need to be received from Legacy or Ehanced Rx FIFO.
-
flexcan_frame_t *frame
-
struct _flexcan_handle
- #include <fsl_flexcan.h>
FlexCAN handle structure.
Public Members
-
flexcan_transfer_callback_t callback
Callback function.
-
void *userData
FlexCAN callback function parameter.
-
flexcan_frame_t *volatile mbFrameBuf[CAN_WORD1_COUNT]
The buffer for received CAN data from Message Buffers.
-
flexcan_fd_frame_t *volatile mbFDFrameBuf[CAN_WORD1_COUNT]
The buffer for received CAN FD data from Message Buffers.
-
flexcan_frame_t *volatile rxFifoFrameBuf
The buffer for received CAN data from Legacy Rx FIFO.
-
size_t rxFifoFrameNum
The number of CAN messages remaining to be received from Legacy or Ehanced Rx FIFO.
-
size_t rxFifoTransferTotalNum
Total CAN Message number need to be received from Legacy or Ehanced Rx FIFO.
-
volatile uint8_t mbState[CAN_WORD1_COUNT]
Message Buffer transfer state.
-
volatile uint8_t rxFifoState
Rx FIFO transfer state.
-
volatile uint32_t timestamp[CAN_WORD1_COUNT]
Mailbox transfer timestamp.
-
flexcan_transfer_callback_t callback
-
struct byteStatus
Public Members
-
bool byteIsRead
The byte n (0~3) was read or not. The type of error and which bit in byte (n) is affected by the error.
-
bool byteIsRead
-
struct __unnamed18__
Public Members
-
uint32_t timestamp
FlexCAN internal Free-Running Counter Time Stamp.
-
uint32_t length
CAN frame data length in bytes (Range: 0~8).
-
uint32_t type
CAN Frame Type(DATA or REMOTE).
-
uint32_t format
CAN Frame Identifier(STD or EXT format).
-
uint32_t __pad0__
Reserved.
-
uint32_t idhit
CAN Rx FIFO filter hit id(This value is only used in Rx FIFO receive mode).
-
uint32_t timestamp
-
struct __unnamed20__
Public Members
-
uint32_t id
CAN Frame Identifier, should be set using FLEXCAN_ID_EXT() or FLEXCAN_ID_STD() macro.
-
uint32_t __pad0__
Reserved.
-
uint32_t id
-
union __unnamed22__
Public Members
- struct _flexcan_frame
- struct _flexcan_frame
-
struct __unnamed24__
Public Members
-
uint32_t dataWord0
CAN Frame payload word0.
-
uint32_t dataWord1
CAN Frame payload word1.
-
uint32_t dataWord0
-
struct __unnamed26__
Public Members
-
uint8_t dataByte3
CAN Frame payload byte3.
-
uint8_t dataByte2
CAN Frame payload byte2.
-
uint8_t dataByte1
CAN Frame payload byte1.
-
uint8_t dataByte0
CAN Frame payload byte0.
-
uint8_t dataByte7
CAN Frame payload byte7.
-
uint8_t dataByte6
CAN Frame payload byte6.
-
uint8_t dataByte5
CAN Frame payload byte5.
-
uint8_t dataByte4
CAN Frame payload byte4.
-
uint8_t dataByte3
-
struct __unnamed28__
Public Members
-
uint32_t timestamp
FlexCAN internal Free-Running Counter Time Stamp.
-
uint32_t length
CAN FD frame data length code (DLC), range see _flexcan_fd_frame_length, When the length <= 8, it equal to the data length, otherwise the number of valid frame data is not equal to the length value. user can use DLC_LENGTH_DECODE(length) macro to get the number of valid data bytes.
-
uint32_t type
CAN Frame Type(DATA or REMOTE).
-
uint32_t format
CAN Frame Identifier(STD or EXT format).
-
uint32_t srr
Substitute Remote request.
-
uint32_t esi
Error State Indicator.
-
uint32_t brs
Bit Rate Switch.
-
uint32_t edl
Extended Data Length.
-
uint32_t timestamp
-
struct __unnamed30__
Public Members
-
uint32_t id
CAN Frame Identifier, should be set using FLEXCAN_ID_EXT() or FLEXCAN_ID_STD() macro.
-
uint32_t __pad0__
Reserved.
-
uint32_t id
-
union __unnamed32__
Public Members
- struct _flexcan_fd_frame
- struct _flexcan_fd_frame
-
struct __unnamed34__
Public Members
-
uint32_t dataWord[16]
CAN FD Frame payload, 16 double word maximum.
-
uint32_t dataWord[16]
-
struct __unnamed36__
Public Members
-
uint8_t dataByte3
CAN Frame payload byte3.
-
uint8_t dataByte2
CAN Frame payload byte2.
-
uint8_t dataByte1
CAN Frame payload byte1.
-
uint8_t dataByte0
CAN Frame payload byte0.
-
uint8_t dataByte7
CAN Frame payload byte7.
-
uint8_t dataByte6
CAN Frame payload byte6.
-
uint8_t dataByte5
CAN Frame payload byte5.
-
uint8_t dataByte4
CAN Frame payload byte4.
-
uint8_t dataByte3
-
union __unnamed38__
Public Members
- struct _flexcan_config
- struct _flexcan_config
-
struct __unnamed40__
Public Members
-
uint32_t baudRate
FlexCAN bit rate in bps, for classical CAN or CANFD nominal phase.
-
uint32_t baudRateFD
FlexCAN FD bit rate in bps, for CANFD data phase.
-
uint32_t baudRate
-
struct __unnamed42__
Public Members
-
uint32_t bitRate
FlexCAN bit rate in bps, for classical CAN or CANFD nominal phase.
-
uint32_t bitRateFD
FlexCAN FD bit rate in bps, for CANFD data phase.
-
uint32_t bitRate
-
union __unnamed44__
Public Members
- struct _flexcan_pn_config
< The data target values 1 which used either for data match “equal to”, “smaller than”, “greater than” comparisons, or as the lower limit value in data match “range
detection”.
- struct _flexcan_pn_config
-
struct __unnamed48__
< The data target values 1 which used either for data match “equal to”, “smaller than”, “greater than” comparisons, or as the lower limit value in data match “range
detection”.
Public Members
-
uint32_t lowerWord0
CAN Frame payload word0.
-
uint32_t lowerWord1
CAN Frame payload word1.
-
uint32_t lowerWord0
-
struct __unnamed50__
Public Members
-
uint8_t lowerByte3
CAN Frame payload byte3.
-
uint8_t lowerByte2
CAN Frame payload byte2.
-
uint8_t lowerByte1
CAN Frame payload byte1.
-
uint8_t lowerByte0
CAN Frame payload byte0.
-
uint8_t lowerByte7
CAN Frame payload byte7.
-
uint8_t lowerByte6
CAN Frame payload byte6.
-
uint8_t lowerByte5
CAN Frame payload byte5.
-
uint8_t lowerByte4
CAN Frame payload byte4.
-
uint8_t lowerByte3
-
union __unnamed46__
Public Members
- struct _flexcan_pn_config
< The data target values 2 which used only as the upper limit value in data match “range
detection” or used to store the data mask in “equal to”.
- struct _flexcan_pn_config
-
struct __unnamed52__
< The data target values 2 which used only as the upper limit value in data match “range
detection” or used to store the data mask in “equal to”.
Public Members
-
uint32_t upperWord0
CAN Frame payload word0.
-
uint32_t upperWord1
CAN Frame payload word1.
-
uint32_t upperWord0
-
struct __unnamed54__
Public Members
-
uint8_t upperByte3
CAN Frame payload byte3.
-
uint8_t upperByte2
CAN Frame payload byte2.
-
uint8_t upperByte1
CAN Frame payload byte1.
-
uint8_t upperByte0
CAN Frame payload byte0.
-
uint8_t upperByte7
CAN Frame payload byte7.
-
uint8_t upperByte6
CAN Frame payload byte6.
-
uint8_t upperByte5
CAN Frame payload byte5.
-
uint8_t upperByte4
CAN Frame payload byte4.
-
uint8_t upperByte3
FlexCAN eDMA Driver
-
void FLEXCAN_TransferCreateHandleEDMA(CAN_Type *base, flexcan_edma_handle_t *handle, flexcan_edma_transfer_callback_t callback, void *userData, edma_handle_t *rxFifoEdmaHandle)
Initializes the FlexCAN handle, which is used in transactional functions.
- Parameters:
base – FlexCAN peripheral base address.
handle – Pointer to flexcan_edma_handle_t structure.
callback – The callback function.
userData – The parameter of the callback function.
rxFifoEdmaHandle – User-requested DMA handle for Rx FIFO DMA transfer.
-
void FLEXCAN_PrepareTransfConfiguration(CAN_Type *base, flexcan_fifo_transfer_t *pFifoXfer, edma_transfer_config_t *pEdmaConfig)
Prepares the eDMA transfer configuration for FLEXCAN Legacy RX FIFO.
This function prepares the eDMA transfer configuration structure according to FLEXCAN Legacy RX FIFO.
- Parameters:
base – FlexCAN peripheral base address.
pFifoXfer – FlexCAN Rx FIFO EDMA transfer structure, see flexcan_fifo_transfer_t.
pEdmaConfig – The user configuration structure of type edma_transfer_t.
-
status_t FLEXCAN_StartTransferDatafromRxFIFO(CAN_Type *base, flexcan_edma_handle_t *handle, edma_transfer_config_t *pEdmaConfig)
Start Transfer Data from the FLEXCAN Legacy Rx FIFO using eDMA.
This function to Update edma transfer confiugration and Start eDMA transfer
- Parameters:
base – FlexCAN peripheral base address.
handle – Pointer to flexcan_edma_handle_t structure.
pEdmaConfig – The user configuration structure of type edma_transfer_t.
- Return values:
kStatus_Success – if succeed, others failed.
kStatus_FLEXCAN_RxFifoBusy – Previous transfer ongoing.
-
status_t FLEXCAN_TransferReceiveFifoEDMA(CAN_Type *base, flexcan_edma_handle_t *handle, flexcan_fifo_transfer_t *pFifoXfer)
Receives the CAN Message from the Legacy Rx FIFO using eDMA.
This function receives the CAN Message using eDMA. This is a non-blocking function, which returns right away. After the CAN Message is received, the receive callback function is called.
- Parameters:
base – FlexCAN peripheral base address.
handle – Pointer to flexcan_edma_handle_t structure.
pFifoXfer – FlexCAN Rx FIFO EDMA transfer structure, see flexcan_fifo_transfer_t.
- Return values:
kStatus_Success – if succeed, others failed.
kStatus_FLEXCAN_RxFifoBusy – Previous transfer ongoing.
-
status_t FLEXCAN_TransferGetReceiveFifoCountEMDA(CAN_Type *base, flexcan_edma_handle_t *handle, size_t *count)
Gets the Legacy Rx Fifo transfer status during a interrupt non-blocking receive.
- Parameters:
base – FlexCAN peripheral base address.
handle – FlexCAN handle pointer.
count – Number of CAN messages receive so far by the non-blocking transaction.
- Return values:
kStatus_InvalidArgument – count is Invalid.
kStatus_Success – Successfully return the count.
-
void FLEXCAN_TransferAbortReceiveFifoEDMA(CAN_Type *base, flexcan_edma_handle_t *handle)
Aborts the receive Legacy/Enhanced Rx FIFO process which used eDMA.
This function aborts the receive Legacy/Enhanced Rx FIFO process which used eDMA.
- Parameters:
base – FlexCAN peripheral base address.
handle – Pointer to flexcan_edma_handle_t structure.
-
FSL_FLEXCAN_EDMA_DRIVER_VERSION
FlexCAN EDMA driver version.
-
typedef struct _flexcan_edma_handle flexcan_edma_handle_t
-
typedef void (*flexcan_edma_transfer_callback_t)(CAN_Type *base, flexcan_edma_handle_t *handle, status_t status, void *userData)
FlexCAN transfer callback function.
-
struct _flexcan_edma_handle
- #include <fsl_flexcan_edma.h>
FlexCAN eDMA handle.
Public Members
-
flexcan_edma_transfer_callback_t callback
Callback function.
-
void *userData
FlexCAN callback function parameter.
-
edma_handle_t *rxFifoEdmaHandle
The EDMA handler for Rx FIFO.
-
volatile uint8_t rxFifoState
Rx FIFO transfer state.
-
size_t frameNum
The number of messages that need to be received.
-
flexcan_edma_transfer_callback_t callback
FlexIO: FlexIO Driver
FlexIO Driver
-
void FLEXIO_GetDefaultConfig(flexio_config_t *userConfig)
Gets the default configuration to configure the FlexIO module. The configuration can used directly to call the FLEXIO_Configure().
Example:
flexio_config_t config; FLEXIO_GetDefaultConfig(&config);
- Parameters:
userConfig – pointer to flexio_config_t structure
-
void FLEXIO_Init(FLEXIO_Type *base, const flexio_config_t *userConfig)
Configures the FlexIO with a FlexIO configuration. The configuration structure can be filled by the user or be set with default values by FLEXIO_GetDefaultConfig().
Example
flexio_config_t config = { .enableFlexio = true, .enableInDoze = false, .enableInDebug = true, .enableFastAccess = false }; FLEXIO_Configure(base, &config);
- Parameters:
base – FlexIO peripheral base address
userConfig – pointer to flexio_config_t structure
-
void FLEXIO_Deinit(FLEXIO_Type *base)
Gates the FlexIO clock. Call this API to stop the FlexIO clock.
Note
After calling this API, call the FLEXO_Init to use the FlexIO module.
- Parameters:
base – FlexIO peripheral base address
-
uint32_t FLEXIO_GetInstance(FLEXIO_Type *base)
Get instance number for FLEXIO module.
- Parameters:
base – FLEXIO peripheral base address.
-
void FLEXIO_Reset(FLEXIO_Type *base)
Resets the FlexIO module.
- Parameters:
base – FlexIO peripheral base address
-
static inline void FLEXIO_Enable(FLEXIO_Type *base, bool enable)
Enables the FlexIO module operation.
- Parameters:
base – FlexIO peripheral base address
enable – true to enable, false to disable.
-
static inline uint32_t FLEXIO_ReadPinInput(FLEXIO_Type *base)
Reads the input data on each of the FlexIO pins.
- Parameters:
base – FlexIO peripheral base address
- Returns:
FlexIO pin input data
-
static inline uint8_t FLEXIO_GetShifterState(FLEXIO_Type *base)
Gets the current state pointer for state mode use.
- Parameters:
base – FlexIO peripheral base address
- Returns:
current State pointer
-
void FLEXIO_SetShifterConfig(FLEXIO_Type *base, uint8_t index, const flexio_shifter_config_t *shifterConfig)
Configures the shifter with the shifter configuration. The configuration structure covers both the SHIFTCTL and SHIFTCFG registers. To configure the shifter to the proper mode, select which timer controls the shifter to shift, whether to generate start bit/stop bit, and the polarity of start bit and stop bit.
Example
flexio_shifter_config_t config = { .timerSelect = 0, .timerPolarity = kFLEXIO_ShifterTimerPolarityOnPositive, .pinConfig = kFLEXIO_PinConfigOpenDrainOrBidirection, .pinPolarity = kFLEXIO_PinActiveLow, .shifterMode = kFLEXIO_ShifterModeTransmit, .inputSource = kFLEXIO_ShifterInputFromPin, .shifterStop = kFLEXIO_ShifterStopBitHigh, .shifterStart = kFLEXIO_ShifterStartBitLow }; FLEXIO_SetShifterConfig(base, &config);
- Parameters:
base – FlexIO peripheral base address
index – Shifter index
shifterConfig – Pointer to flexio_shifter_config_t structure
-
void FLEXIO_SetTimerConfig(FLEXIO_Type *base, uint8_t index, const flexio_timer_config_t *timerConfig)
Configures the timer with the timer configuration. The configuration structure covers both the TIMCTL and TIMCFG registers. To configure the timer to the proper mode, select trigger source for timer and the timer pin output and the timing for timer.
Example
flexio_timer_config_t config = { .triggerSelect = FLEXIO_TIMER_TRIGGER_SEL_SHIFTnSTAT(0), .triggerPolarity = kFLEXIO_TimerTriggerPolarityActiveLow, .triggerSource = kFLEXIO_TimerTriggerSourceInternal, .pinConfig = kFLEXIO_PinConfigOpenDrainOrBidirection, .pinSelect = 0, .pinPolarity = kFLEXIO_PinActiveHigh, .timerMode = kFLEXIO_TimerModeDual8BitBaudBit, .timerOutput = kFLEXIO_TimerOutputZeroNotAffectedByReset, .timerDecrement = kFLEXIO_TimerDecSrcOnFlexIOClockShiftTimerOutput, .timerReset = kFLEXIO_TimerResetOnTimerPinEqualToTimerOutput, .timerDisable = kFLEXIO_TimerDisableOnTimerCompare, .timerEnable = kFLEXIO_TimerEnableOnTriggerHigh, .timerStop = kFLEXIO_TimerStopBitEnableOnTimerDisable, .timerStart = kFLEXIO_TimerStartBitEnabled }; FLEXIO_SetTimerConfig(base, &config);
- Parameters:
base – FlexIO peripheral base address
index – Timer index
timerConfig – Pointer to the flexio_timer_config_t structure
-
static inline void FLEXIO_SetClockMode(FLEXIO_Type *base, uint8_t index, flexio_timer_decrement_source_t clocksource)
This function set the value of the prescaler on flexio channels.
- Parameters:
base – Pointer to the FlexIO simulated peripheral type.
index – Timer index
clocksource – Set clock value
-
static inline void FLEXIO_EnableShifterStatusInterrupts(FLEXIO_Type *base, uint32_t mask)
Enables the shifter status interrupt. The interrupt generates when the corresponding SSF is set.
Note
For multiple shifter status interrupt enable, for example, two shifter status enable, can calculate the mask by using ((1 << shifter index0) | (1 << shifter index1))
- Parameters:
base – FlexIO peripheral base address
mask – The shifter status mask which can be calculated by (1 << shifter index)
-
static inline void FLEXIO_DisableShifterStatusInterrupts(FLEXIO_Type *base, uint32_t mask)
Disables the shifter status interrupt. The interrupt won’t generate when the corresponding SSF is set.
Note
For multiple shifter status interrupt enable, for example, two shifter status enable, can calculate the mask by using ((1 << shifter index0) | (1 << shifter index1))
- Parameters:
base – FlexIO peripheral base address
mask – The shifter status mask which can be calculated by (1 << shifter index)
-
static inline void FLEXIO_EnableShifterErrorInterrupts(FLEXIO_Type *base, uint32_t mask)
Enables the shifter error interrupt. The interrupt generates when the corresponding SEF is set.
Note
For multiple shifter error interrupt enable, for example, two shifter error enable, can calculate the mask by using ((1 << shifter index0) | (1 << shifter index1))
- Parameters:
base – FlexIO peripheral base address
mask – The shifter error mask which can be calculated by (1 << shifter index)
-
static inline void FLEXIO_DisableShifterErrorInterrupts(FLEXIO_Type *base, uint32_t mask)
Disables the shifter error interrupt. The interrupt won’t generate when the corresponding SEF is set.
Note
For multiple shifter error interrupt enable, for example, two shifter error enable, can calculate the mask by using ((1 << shifter index0) | (1 << shifter index1))
- Parameters:
base – FlexIO peripheral base address
mask – The shifter error mask which can be calculated by (1 << shifter index)
-
static inline void FLEXIO_EnableTimerStatusInterrupts(FLEXIO_Type *base, uint32_t mask)
Enables the timer status interrupt. The interrupt generates when the corresponding SSF is set.
Note
For multiple timer status interrupt enable, for example, two timer status enable, can calculate the mask by using ((1 << timer index0) | (1 << timer index1))
- Parameters:
base – FlexIO peripheral base address
mask – The timer status mask which can be calculated by (1 << timer index)
-
static inline void FLEXIO_DisableTimerStatusInterrupts(FLEXIO_Type *base, uint32_t mask)
Disables the timer status interrupt. The interrupt won’t generate when the corresponding SSF is set.
Note
For multiple timer status interrupt enable, for example, two timer status enable, can calculate the mask by using ((1 << timer index0) | (1 << timer index1))
- Parameters:
base – FlexIO peripheral base address
mask – The timer status mask which can be calculated by (1 << timer index)
-
static inline uint32_t FLEXIO_GetShifterStatusFlags(FLEXIO_Type *base)
Gets the shifter status flags.
- Parameters:
base – FlexIO peripheral base address
- Returns:
Shifter status flags
-
static inline void FLEXIO_ClearShifterStatusFlags(FLEXIO_Type *base, uint32_t mask)
Clears the shifter status flags.
Note
For clearing multiple shifter status flags, for example, two shifter status flags, can calculate the mask by using ((1 << shifter index0) | (1 << shifter index1))
- Parameters:
base – FlexIO peripheral base address
mask – The shifter status mask which can be calculated by (1 << shifter index)
-
static inline uint32_t FLEXIO_GetShifterErrorFlags(FLEXIO_Type *base)
Gets the shifter error flags.
- Parameters:
base – FlexIO peripheral base address
- Returns:
Shifter error flags
-
static inline void FLEXIO_ClearShifterErrorFlags(FLEXIO_Type *base, uint32_t mask)
Clears the shifter error flags.
Note
For clearing multiple shifter error flags, for example, two shifter error flags, can calculate the mask by using ((1 << shifter index0) | (1 << shifter index1))
- Parameters:
base – FlexIO peripheral base address
mask – The shifter error mask which can be calculated by (1 << shifter index)
-
static inline uint32_t FLEXIO_GetTimerStatusFlags(FLEXIO_Type *base)
Gets the timer status flags.
- Parameters:
base – FlexIO peripheral base address
- Returns:
Timer status flags
-
static inline void FLEXIO_ClearTimerStatusFlags(FLEXIO_Type *base, uint32_t mask)
Clears the timer status flags.
Note
For clearing multiple timer status flags, for example, two timer status flags, can calculate the mask by using ((1 << timer index0) | (1 << timer index1))
- Parameters:
base – FlexIO peripheral base address
mask – The timer status mask which can be calculated by (1 << timer index)
-
static inline void FLEXIO_EnableShifterStatusDMA(FLEXIO_Type *base, uint32_t mask, bool enable)
Enables/disables the shifter status DMA. The DMA request generates when the corresponding SSF is set.
Note
For multiple shifter status DMA enables, for example, calculate the mask by using ((1 << shifter index0) | (1 << shifter index1))
- Parameters:
base – FlexIO peripheral base address
mask – The shifter status mask which can be calculated by (1 << shifter index)
enable – True to enable, false to disable.
-
uint32_t FLEXIO_GetShifterBufferAddress(FLEXIO_Type *base, flexio_shifter_buffer_type_t type, uint8_t index)
Gets the shifter buffer address for the DMA transfer usage.
- Parameters:
base – FlexIO peripheral base address
type – Shifter type of flexio_shifter_buffer_type_t
index – Shifter index
- Returns:
Corresponding shifter buffer index
-
status_t FLEXIO_RegisterHandleIRQ(void *base, void *handle, flexio_isr_t isr)
Registers the handle and the interrupt handler for the FlexIO-simulated peripheral.
- Parameters:
base – Pointer to the FlexIO simulated peripheral type.
handle – Pointer to the handler for FlexIO simulated peripheral.
isr – FlexIO simulated peripheral interrupt handler.
- Return values:
kStatus_Success – Successfully create the handle.
kStatus_OutOfRange – The FlexIO type/handle/ISR table out of range.
-
status_t FLEXIO_UnregisterHandleIRQ(void *base)
Unregisters the handle and the interrupt handler for the FlexIO-simulated peripheral.
- Parameters:
base – Pointer to the FlexIO simulated peripheral type.
- Return values:
kStatus_Success – Successfully create the handle.
kStatus_OutOfRange – The FlexIO type/handle/ISR table out of range.
-
static inline void FLEXIO_ClearPortOutput(FLEXIO_Type *base, uint32_t mask)
Sets the output level of the multiple FLEXIO pins to the logic 0.
- Parameters:
base – FlexIO peripheral base address
mask – FLEXIO pin number mask
-
static inline void FLEXIO_SetPortOutput(FLEXIO_Type *base, uint32_t mask)
Sets the output level of the multiple FLEXIO pins to the logic 1.
- Parameters:
base – FlexIO peripheral base address
mask – FLEXIO pin number mask
-
static inline void FLEXIO_TogglePortOutput(FLEXIO_Type *base, uint32_t mask)
Reverses the current output logic of the multiple FLEXIO pins.
- Parameters:
base – FlexIO peripheral base address
mask – FLEXIO pin number mask
-
static inline void FLEXIO_PinWrite(FLEXIO_Type *base, uint32_t pin, uint8_t output)
Sets the output level of the FLEXIO pins to the logic 1 or 0.
- Parameters:
base – FlexIO peripheral base address
pin – FLEXIO pin number.
output – FLEXIO pin output logic level.
0: corresponding pin output low-logic level.
1: corresponding pin output high-logic level.
-
static inline void FLEXIO_EnablePinOutput(FLEXIO_Type *base, uint32_t pin)
Enables the FLEXIO output pin function.
- Parameters:
base – FlexIO peripheral base address
pin – FLEXIO pin number.
-
static inline uint32_t FLEXIO_PinRead(FLEXIO_Type *base, uint32_t pin)
Reads the current input value of the FLEXIO pin.
- Parameters:
base – FlexIO peripheral base address
pin – FLEXIO pin number.
- Return values:
FLEXIO – port input value
0: corresponding pin input low-logic level.
1: corresponding pin input high-logic level.
-
static inline uint32_t FLEXIO_GetPinStatus(FLEXIO_Type *base, uint32_t pin)
Gets the FLEXIO input pin status.
- Parameters:
base – FlexIO peripheral base address
pin – FLEXIO pin number.
- Return values:
FLEXIO – port input status
0: corresponding pin input capture no status.
1: corresponding pin input capture rising or falling edge.
-
static inline void FLEXIO_ClearPortStatus(FLEXIO_Type *base, uint32_t mask)
Clears the multiple FLEXIO input pins status.
- Parameters:
base – FlexIO peripheral base address
mask – FLEXIO pin number mask
-
FSL_FLEXIO_DRIVER_VERSION
FlexIO driver version.
-
enum _flexio_timer_trigger_polarity
Define time of timer trigger polarity.
Values:
-
enumerator kFLEXIO_TimerTriggerPolarityActiveHigh
Active high.
-
enumerator kFLEXIO_TimerTriggerPolarityActiveLow
Active low.
-
enumerator kFLEXIO_TimerTriggerPolarityActiveHigh
-
enum _flexio_timer_trigger_source
Define type of timer trigger source.
Values:
-
enumerator kFLEXIO_TimerTriggerSourceExternal
External trigger selected.
-
enumerator kFLEXIO_TimerTriggerSourceInternal
Internal trigger selected.
-
enumerator kFLEXIO_TimerTriggerSourceExternal
-
enum _flexio_pin_config
Define type of timer/shifter pin configuration.
Values:
-
enumerator kFLEXIO_PinConfigOutputDisabled
Pin output disabled.
-
enumerator kFLEXIO_PinConfigOpenDrainOrBidirection
Pin open drain or bidirectional output enable.
-
enumerator kFLEXIO_PinConfigBidirectionOutputData
Pin bidirectional output data.
-
enumerator kFLEXIO_PinConfigOutput
Pin output.
-
enumerator kFLEXIO_PinConfigOutputDisabled
-
enum _flexio_pin_polarity
Definition of pin polarity.
Values:
-
enumerator kFLEXIO_PinActiveHigh
Active high.
-
enumerator kFLEXIO_PinActiveLow
Active low.
-
enumerator kFLEXIO_PinActiveHigh
-
enum _flexio_timer_mode
Define type of timer work mode.
Values:
-
enumerator kFLEXIO_TimerModeDisabled
Timer Disabled.
-
enumerator kFLEXIO_TimerModeDual8BitBaudBit
Dual 8-bit counters baud/bit mode.
-
enumerator kFLEXIO_TimerModeDual8BitPWM
Dual 8-bit counters PWM mode.
-
enumerator kFLEXIO_TimerModeSingle16Bit
Single 16-bit counter mode.
-
enumerator kFLEXIO_TimerModeDisabled
-
enum _flexio_timer_output
Define type of timer initial output or timer reset condition.
Values:
-
enumerator kFLEXIO_TimerOutputOneNotAffectedByReset
Logic one when enabled and is not affected by timer reset.
-
enumerator kFLEXIO_TimerOutputZeroNotAffectedByReset
Logic zero when enabled and is not affected by timer reset.
-
enumerator kFLEXIO_TimerOutputOneAffectedByReset
Logic one when enabled and on timer reset.
-
enumerator kFLEXIO_TimerOutputZeroAffectedByReset
Logic zero when enabled and on timer reset.
-
enumerator kFLEXIO_TimerOutputOneNotAffectedByReset
-
enum _flexio_timer_decrement_source
Define type of timer decrement.
Values:
-
enumerator kFLEXIO_TimerDecSrcOnFlexIOClockShiftTimerOutput
Decrement counter on FlexIO clock, Shift clock equals Timer output.
-
enumerator kFLEXIO_TimerDecSrcOnTriggerInputShiftTimerOutput
Decrement counter on Trigger input (both edges), Shift clock equals Timer output.
-
enumerator kFLEXIO_TimerDecSrcOnPinInputShiftPinInput
Decrement counter on Pin input (both edges), Shift clock equals Pin input.
-
enumerator kFLEXIO_TimerDecSrcOnTriggerInputShiftTriggerInput
Decrement counter on Trigger input (both edges), Shift clock equals Trigger input.
-
enumerator kFLEXIO_TimerDecSrcOnFlexIOClockShiftTimerOutput
-
enum _flexio_timer_reset_condition
Define type of timer reset condition.
Values:
-
enumerator kFLEXIO_TimerResetNever
Timer never reset.
-
enumerator kFLEXIO_TimerResetOnTimerPinEqualToTimerOutput
Timer reset on Timer Pin equal to Timer Output.
-
enumerator kFLEXIO_TimerResetOnTimerTriggerEqualToTimerOutput
Timer reset on Timer Trigger equal to Timer Output.
-
enumerator kFLEXIO_TimerResetOnTimerPinRisingEdge
Timer reset on Timer Pin rising edge.
-
enumerator kFLEXIO_TimerResetOnTimerTriggerRisingEdge
Timer reset on Trigger rising edge.
-
enumerator kFLEXIO_TimerResetOnTimerTriggerBothEdge
Timer reset on Trigger rising or falling edge.
-
enumerator kFLEXIO_TimerResetNever
-
enum _flexio_timer_disable_condition
Define type of timer disable condition.
Values:
-
enumerator kFLEXIO_TimerDisableNever
Timer never disabled.
-
enumerator kFLEXIO_TimerDisableOnPreTimerDisable
Timer disabled on Timer N-1 disable.
-
enumerator kFLEXIO_TimerDisableOnTimerCompare
Timer disabled on Timer compare.
-
enumerator kFLEXIO_TimerDisableOnTimerCompareTriggerLow
Timer disabled on Timer compare and Trigger Low.
-
enumerator kFLEXIO_TimerDisableOnPinBothEdge
Timer disabled on Pin rising or falling edge.
-
enumerator kFLEXIO_TimerDisableOnPinBothEdgeTriggerHigh
Timer disabled on Pin rising or falling edge provided Trigger is high.
-
enumerator kFLEXIO_TimerDisableOnTriggerFallingEdge
Timer disabled on Trigger falling edge.
-
enumerator kFLEXIO_TimerDisableNever
-
enum _flexio_timer_enable_condition
Define type of timer enable condition.
Values:
-
enumerator kFLEXIO_TimerEnabledAlways
Timer always enabled.
-
enumerator kFLEXIO_TimerEnableOnPrevTimerEnable
Timer enabled on Timer N-1 enable.
-
enumerator kFLEXIO_TimerEnableOnTriggerHigh
Timer enabled on Trigger high.
-
enumerator kFLEXIO_TimerEnableOnTriggerHighPinHigh
Timer enabled on Trigger high and Pin high.
-
enumerator kFLEXIO_TimerEnableOnPinRisingEdge
Timer enabled on Pin rising edge.
-
enumerator kFLEXIO_TimerEnableOnPinRisingEdgeTriggerHigh
Timer enabled on Pin rising edge and Trigger high.
-
enumerator kFLEXIO_TimerEnableOnTriggerRisingEdge
Timer enabled on Trigger rising edge.
-
enumerator kFLEXIO_TimerEnableOnTriggerBothEdge
Timer enabled on Trigger rising or falling edge.
-
enumerator kFLEXIO_TimerEnabledAlways
-
enum _flexio_timer_stop_bit_condition
Define type of timer stop bit generate condition.
Values:
-
enumerator kFLEXIO_TimerStopBitDisabled
Stop bit disabled.
-
enumerator kFLEXIO_TimerStopBitEnableOnTimerCompare
Stop bit is enabled on timer compare.
-
enumerator kFLEXIO_TimerStopBitEnableOnTimerDisable
Stop bit is enabled on timer disable.
-
enumerator kFLEXIO_TimerStopBitEnableOnTimerCompareDisable
Stop bit is enabled on timer compare and timer disable.
-
enumerator kFLEXIO_TimerStopBitDisabled
-
enum _flexio_timer_start_bit_condition
Define type of timer start bit generate condition.
Values:
-
enumerator kFLEXIO_TimerStartBitDisabled
Start bit disabled.
-
enumerator kFLEXIO_TimerStartBitEnabled
Start bit enabled.
-
enumerator kFLEXIO_TimerStartBitDisabled
-
enum _flexio_timer_output_state
FlexIO as PWM channel output state.
Values:
-
enumerator kFLEXIO_PwmLow
The output state of PWM channel is low
-
enumerator kFLEXIO_PwmHigh
The output state of PWM channel is high
-
enumerator kFLEXIO_PwmLow
-
enum _flexio_shifter_timer_polarity
Define type of timer polarity for shifter control.
Values:
-
enumerator kFLEXIO_ShifterTimerPolarityOnPositive
Shift on positive edge of shift clock.
-
enumerator kFLEXIO_ShifterTimerPolarityOnNegitive
Shift on negative edge of shift clock.
-
enumerator kFLEXIO_ShifterTimerPolarityOnPositive
-
enum _flexio_shifter_mode
Define type of shifter working mode.
Values:
-
enumerator kFLEXIO_ShifterDisabled
Shifter is disabled.
-
enumerator kFLEXIO_ShifterModeReceive
Receive mode.
-
enumerator kFLEXIO_ShifterModeTransmit
Transmit mode.
-
enumerator kFLEXIO_ShifterModeMatchStore
Match store mode.
-
enumerator kFLEXIO_ShifterModeMatchContinuous
Match continuous mode.
-
enumerator kFLEXIO_ShifterModeState
SHIFTBUF contents are used for storing programmable state attributes.
-
enumerator kFLEXIO_ShifterModeLogic
SHIFTBUF contents are used for implementing programmable logic look up table.
-
enumerator kFLEXIO_ShifterDisabled
-
enum _flexio_shifter_input_source
Define type of shifter input source.
Values:
-
enumerator kFLEXIO_ShifterInputFromPin
Shifter input from pin.
-
enumerator kFLEXIO_ShifterInputFromNextShifterOutput
Shifter input from Shifter N+1.
-
enumerator kFLEXIO_ShifterInputFromPin
-
enum _flexio_shifter_stop_bit
Define of STOP bit configuration.
Values:
-
enumerator kFLEXIO_ShifterStopBitDisable
Disable shifter stop bit.
-
enumerator kFLEXIO_ShifterStopBitLow
Set shifter stop bit to logic low level.
-
enumerator kFLEXIO_ShifterStopBitHigh
Set shifter stop bit to logic high level.
-
enumerator kFLEXIO_ShifterStopBitDisable
-
enum _flexio_shifter_start_bit
Define type of START bit configuration.
Values:
-
enumerator kFLEXIO_ShifterStartBitDisabledLoadDataOnEnable
Disable shifter start bit, transmitter loads data on enable.
-
enumerator kFLEXIO_ShifterStartBitDisabledLoadDataOnShift
Disable shifter start bit, transmitter loads data on first shift.
-
enumerator kFLEXIO_ShifterStartBitLow
Set shifter start bit to logic low level.
-
enumerator kFLEXIO_ShifterStartBitHigh
Set shifter start bit to logic high level.
-
enumerator kFLEXIO_ShifterStartBitDisabledLoadDataOnEnable
-
enum _flexio_shifter_buffer_type
Define FlexIO shifter buffer type.
Values:
-
enumerator kFLEXIO_ShifterBuffer
Shifter Buffer N Register.
-
enumerator kFLEXIO_ShifterBufferBitSwapped
Shifter Buffer N Bit Byte Swapped Register.
-
enumerator kFLEXIO_ShifterBufferByteSwapped
Shifter Buffer N Byte Swapped Register.
-
enumerator kFLEXIO_ShifterBufferBitByteSwapped
Shifter Buffer N Bit Swapped Register.
-
enumerator kFLEXIO_ShifterBufferNibbleByteSwapped
Shifter Buffer N Nibble Byte Swapped Register.
-
enumerator kFLEXIO_ShifterBufferHalfWordSwapped
Shifter Buffer N Half Word Swapped Register.
-
enumerator kFLEXIO_ShifterBufferNibbleSwapped
Shifter Buffer N Nibble Swapped Register.
-
enumerator kFLEXIO_ShifterBuffer
-
enum _flexio_gpio_direction
FLEXIO gpio direction definition.
Values:
-
enumerator kFLEXIO_DigitalInput
Set current pin as digital input
-
enumerator kFLEXIO_DigitalOutput
Set current pin as digital output
-
enumerator kFLEXIO_DigitalInput
-
enum _flexio_pin_input_config
FLEXIO gpio input config.
Values:
-
enumerator kFLEXIO_InputInterruptDisabled
Interrupt request is disabled.
-
enumerator kFLEXIO_InputInterruptEnable
Interrupt request is enable.
-
enumerator kFLEXIO_FlagRisingEdgeEnable
Input pin flag on rising edge.
-
enumerator kFLEXIO_FlagFallingEdgeEnable
Input pin flag on falling edge.
-
enumerator kFLEXIO_InputInterruptDisabled
-
typedef enum _flexio_timer_trigger_polarity flexio_timer_trigger_polarity_t
Define time of timer trigger polarity.
-
typedef enum _flexio_timer_trigger_source flexio_timer_trigger_source_t
Define type of timer trigger source.
-
typedef enum _flexio_pin_config flexio_pin_config_t
Define type of timer/shifter pin configuration.
-
typedef enum _flexio_pin_polarity flexio_pin_polarity_t
Definition of pin polarity.
-
typedef enum _flexio_timer_mode flexio_timer_mode_t
Define type of timer work mode.
-
typedef enum _flexio_timer_output flexio_timer_output_t
Define type of timer initial output or timer reset condition.
-
typedef enum _flexio_timer_decrement_source flexio_timer_decrement_source_t
Define type of timer decrement.
-
typedef enum _flexio_timer_reset_condition flexio_timer_reset_condition_t
Define type of timer reset condition.
-
typedef enum _flexio_timer_disable_condition flexio_timer_disable_condition_t
Define type of timer disable condition.
-
typedef enum _flexio_timer_enable_condition flexio_timer_enable_condition_t
Define type of timer enable condition.
-
typedef enum _flexio_timer_stop_bit_condition flexio_timer_stop_bit_condition_t
Define type of timer stop bit generate condition.
-
typedef enum _flexio_timer_start_bit_condition flexio_timer_start_bit_condition_t
Define type of timer start bit generate condition.
-
typedef enum _flexio_timer_output_state flexio_timer_output_state_t
FlexIO as PWM channel output state.
-
typedef enum _flexio_shifter_timer_polarity flexio_shifter_timer_polarity_t
Define type of timer polarity for shifter control.
-
typedef enum _flexio_shifter_mode flexio_shifter_mode_t
Define type of shifter working mode.
-
typedef enum _flexio_shifter_input_source flexio_shifter_input_source_t
Define type of shifter input source.
-
typedef enum _flexio_shifter_stop_bit flexio_shifter_stop_bit_t
Define of STOP bit configuration.
-
typedef enum _flexio_shifter_start_bit flexio_shifter_start_bit_t
Define type of START bit configuration.
-
typedef enum _flexio_shifter_buffer_type flexio_shifter_buffer_type_t
Define FlexIO shifter buffer type.
-
typedef struct _flexio_config_ flexio_config_t
Define FlexIO user configuration structure.
-
typedef struct _flexio_timer_config flexio_timer_config_t
Define FlexIO timer configuration structure.
-
typedef struct _flexio_shifter_config flexio_shifter_config_t
Define FlexIO shifter configuration structure.
-
typedef enum _flexio_gpio_direction flexio_gpio_direction_t
FLEXIO gpio direction definition.
-
typedef enum _flexio_pin_input_config flexio_pin_input_config_t
FLEXIO gpio input config.
-
typedef struct _flexio_gpio_config flexio_gpio_config_t
The FLEXIO pin configuration structure.
Each pin can only be configured as either an output pin or an input pin at a time. If configured as an input pin, use inputConfig param. If configured as an output pin, use outputLogic.
-
typedef void (*flexio_isr_t)(void *base, void *handle)
typedef for FlexIO simulated driver interrupt handler.
-
FLEXIO_Type *const s_flexioBases[]
Pointers to flexio bases for each instance.
-
const clock_ip_name_t s_flexioClocks[]
Pointers to flexio clocks for each instance.
-
void FLEXIO_SetPinConfig(FLEXIO_Type *base, uint32_t pin, flexio_gpio_config_t *config)
Configure a FLEXIO pin used by the board.
To Config the FLEXIO PIN, define a pin configuration, as either input or output, in the user file. Then, call the FLEXIO_SetPinConfig() function.
This is an example to define an input pin or an output pin configuration.
Define a digital input pin configuration, flexio_gpio_config_t config = { kFLEXIO_DigitalInput, 0U, kFLEXIO_FlagRisingEdgeEnable | kFLEXIO_InputInterruptEnable, } Define a digital output pin configuration, flexio_gpio_config_t config = { kFLEXIO_DigitalOutput, 0U, 0U }
- Parameters:
base – FlexIO peripheral base address
pin – FLEXIO pin number.
config – FLEXIO pin configuration pointer.
-
FLEXIO_TIMER_TRIGGER_SEL_PININPUT(x)
Calculate FlexIO timer trigger.
-
FLEXIO_TIMER_TRIGGER_SEL_SHIFTnSTAT(x)
-
FLEXIO_TIMER_TRIGGER_SEL_TIMn(x)
-
struct _flexio_config_
- #include <fsl_flexio.h>
Define FlexIO user configuration structure.
Public Members
-
bool enableFlexio
Enable/disable FlexIO module
-
bool enableInDoze
Enable/disable FlexIO operation in doze mode
-
bool enableInDebug
Enable/disable FlexIO operation in debug mode
-
bool enableFastAccess
Enable/disable fast access to FlexIO registers, fast access requires the FlexIO clock to be at least twice the frequency of the bus clock.
-
bool enableFlexio
-
struct _flexio_timer_config
- #include <fsl_flexio.h>
Define FlexIO timer configuration structure.
Public Members
-
uint32_t triggerSelect
The internal trigger selection number using MACROs.
-
flexio_timer_trigger_polarity_t triggerPolarity
Trigger Polarity.
-
flexio_timer_trigger_source_t triggerSource
Trigger Source, internal (see ‘trgsel’) or external.
-
flexio_pin_config_t pinConfig
Timer Pin Configuration.
-
uint32_t pinSelect
Timer Pin number Select.
-
flexio_pin_polarity_t pinPolarity
Timer Pin Polarity.
-
flexio_timer_mode_t timerMode
Timer work Mode.
-
flexio_timer_output_t timerOutput
Configures the initial state of the Timer Output and whether it is affected by the Timer reset.
-
flexio_timer_decrement_source_t timerDecrement
Configures the source of the Timer decrement and the source of the Shift clock.
-
flexio_timer_reset_condition_t timerReset
Configures the condition that causes the timer counter (and optionally the timer output) to be reset.
-
flexio_timer_disable_condition_t timerDisable
Configures the condition that causes the Timer to be disabled and stop decrementing.
-
flexio_timer_enable_condition_t timerEnable
Configures the condition that causes the Timer to be enabled and start decrementing.
-
flexio_timer_stop_bit_condition_t timerStop
Timer STOP Bit generation.
-
flexio_timer_start_bit_condition_t timerStart
Timer STRAT Bit generation.
-
uint32_t timerCompare
Value for Timer Compare N Register.
-
uint32_t triggerSelect
-
struct _flexio_shifter_config
- #include <fsl_flexio.h>
Define FlexIO shifter configuration structure.
Public Members
-
uint32_t timerSelect
Selects which Timer is used for controlling the logic/shift register and generating the Shift clock.
-
flexio_shifter_timer_polarity_t timerPolarity
Timer Polarity.
-
flexio_pin_config_t pinConfig
Shifter Pin Configuration.
-
uint32_t pinSelect
Shifter Pin number Select.
-
flexio_pin_polarity_t pinPolarity
Shifter Pin Polarity.
-
flexio_shifter_mode_t shifterMode
Configures the mode of the Shifter.
-
uint32_t parallelWidth
Configures the parallel width when using parallel mode.
-
flexio_shifter_input_source_t inputSource
Selects the input source for the shifter.
-
flexio_shifter_stop_bit_t shifterStop
Shifter STOP bit.
-
flexio_shifter_start_bit_t shifterStart
Shifter START bit.
-
uint32_t timerSelect
-
struct _flexio_gpio_config
- #include <fsl_flexio.h>
The FLEXIO pin configuration structure.
Each pin can only be configured as either an output pin or an input pin at a time. If configured as an input pin, use inputConfig param. If configured as an output pin, use outputLogic.
Public Members
-
flexio_gpio_direction_t pinDirection
FLEXIO pin direction, input or output
-
uint8_t outputLogic
Set a default output logic, which has no use in input
-
uint8_t inputConfig
Set an input config
-
flexio_gpio_direction_t pinDirection
FlexIO eDMA I2S Driver
-
void FLEXIO_I2S_TransferTxCreateHandleEDMA(FLEXIO_I2S_Type *base, flexio_i2s_edma_handle_t *handle, flexio_i2s_edma_callback_t callback, void *userData, edma_handle_t *dmaHandle)
Initializes the FlexIO I2S eDMA handle.
This function initializes the FlexIO I2S master DMA handle which can be used for other FlexIO I2S master transactional APIs. Usually, for a specified FlexIO I2S instance, call this API once to get the initialized handle.
- Parameters:
base – FlexIO I2S peripheral base address.
handle – FlexIO I2S eDMA handle pointer.
callback – FlexIO I2S eDMA callback function called while finished a block.
userData – User parameter for callback.
dmaHandle – eDMA handle for FlexIO I2S. This handle is a static value allocated by users.
-
void FLEXIO_I2S_TransferRxCreateHandleEDMA(FLEXIO_I2S_Type *base, flexio_i2s_edma_handle_t *handle, flexio_i2s_edma_callback_t callback, void *userData, edma_handle_t *dmaHandle)
Initializes the FlexIO I2S Rx eDMA handle.
This function initializes the FlexIO I2S slave DMA handle which can be used for other FlexIO I2S master transactional APIs. Usually, for a specified FlexIO I2S instance, call this API once to get the initialized handle.
- Parameters:
base – FlexIO I2S peripheral base address.
handle – FlexIO I2S eDMA handle pointer.
callback – FlexIO I2S eDMA callback function called while finished a block.
userData – User parameter for callback.
dmaHandle – eDMA handle for FlexIO I2S. This handle is a static value allocated by users.
-
void FLEXIO_I2S_TransferSetFormatEDMA(FLEXIO_I2S_Type *base, flexio_i2s_edma_handle_t *handle, flexio_i2s_format_t *format, uint32_t srcClock_Hz)
Configures the FlexIO I2S Tx audio format.
Audio format can be changed in run-time of FlexIO I2S. This function configures the sample rate and audio data format to be transferred. This function also sets the eDMA parameter according to format.
- Parameters:
base – FlexIO I2S peripheral base address.
handle – FlexIO I2S eDMA handle pointer
format – Pointer to FlexIO I2S audio data format structure.
srcClock_Hz – FlexIO I2S clock source frequency in Hz, it should be 0 while in slave mode.
-
status_t FLEXIO_I2S_TransferSendEDMA(FLEXIO_I2S_Type *base, flexio_i2s_edma_handle_t *handle, flexio_i2s_transfer_t *xfer)
Performs a non-blocking FlexIO I2S transfer using DMA.
Note
This interface returned immediately after transfer initiates. Users should call FLEXIO_I2S_GetTransferStatus to poll the transfer status and check whether the FlexIO I2S transfer is finished.
- Parameters:
base – FlexIO I2S peripheral base address.
handle – FlexIO I2S DMA handle pointer.
xfer – Pointer to DMA transfer structure.
- Return values:
kStatus_Success – Start a FlexIO I2S eDMA send successfully.
kStatus_InvalidArgument – The input arguments is invalid.
kStatus_TxBusy – FlexIO I2S is busy sending data.
-
status_t FLEXIO_I2S_TransferReceiveEDMA(FLEXIO_I2S_Type *base, flexio_i2s_edma_handle_t *handle, flexio_i2s_transfer_t *xfer)
Performs a non-blocking FlexIO I2S receive using eDMA.
Note
This interface returned immediately after transfer initiates. Users should call FLEXIO_I2S_GetReceiveRemainingBytes to poll the transfer status and check whether the FlexIO I2S transfer is finished.
- Parameters:
base – FlexIO I2S peripheral base address.
handle – FlexIO I2S DMA handle pointer.
xfer – Pointer to DMA transfer structure.
- Return values:
kStatus_Success – Start a FlexIO I2S eDMA receive successfully.
kStatus_InvalidArgument – The input arguments is invalid.
kStatus_RxBusy – FlexIO I2S is busy receiving data.
-
void FLEXIO_I2S_TransferAbortSendEDMA(FLEXIO_I2S_Type *base, flexio_i2s_edma_handle_t *handle)
Aborts a FlexIO I2S transfer using eDMA.
- Parameters:
base – FlexIO I2S peripheral base address.
handle – FlexIO I2S DMA handle pointer.
-
void FLEXIO_I2S_TransferAbortReceiveEDMA(FLEXIO_I2S_Type *base, flexio_i2s_edma_handle_t *handle)
Aborts a FlexIO I2S receive using eDMA.
- Parameters:
base – FlexIO I2S peripheral base address.
handle – FlexIO I2S DMA handle pointer.
-
status_t FLEXIO_I2S_TransferGetSendCountEDMA(FLEXIO_I2S_Type *base, flexio_i2s_edma_handle_t *handle, size_t *count)
Gets the remaining bytes to be sent.
- Parameters:
base – FlexIO I2S peripheral base address.
handle – FlexIO I2S DMA handle pointer.
count – Bytes sent.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is not a non-blocking transaction currently in progress.
-
status_t FLEXIO_I2S_TransferGetReceiveCountEDMA(FLEXIO_I2S_Type *base, flexio_i2s_edma_handle_t *handle, size_t *count)
Get the remaining bytes to be received.
- Parameters:
base – FlexIO I2S peripheral base address.
handle – FlexIO I2S DMA handle pointer.
count – Bytes received.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is not a non-blocking transaction currently in progress.
-
FSL_FLEXIO_I2S_EDMA_DRIVER_VERSION
FlexIO I2S EDMA driver version 2.1.8.
-
typedef struct _flexio_i2s_edma_handle flexio_i2s_edma_handle_t
-
typedef void (*flexio_i2s_edma_callback_t)(FLEXIO_I2S_Type *base, flexio_i2s_edma_handle_t *handle, status_t status, void *userData)
FlexIO I2S eDMA transfer callback function for finish and error.
-
struct _flexio_i2s_edma_handle
- #include <fsl_flexio_i2s_edma.h>
FlexIO I2S DMA transfer handle, users should not touch the content of the handle.
Public Members
-
edma_handle_t *dmaHandle
DMA handler for FlexIO I2S send
-
uint8_t bytesPerFrame
Bytes in a frame
-
uint8_t nbytes
eDMA minor byte transfer count initially configured.
-
uint32_t state
Internal state for FlexIO I2S eDMA transfer
-
flexio_i2s_edma_callback_t callback
Callback for users while transfer finish or error occurred
-
void *userData
User callback parameter
-
edma_tcd_t tcd[(4U) + 1U]
TCD pool for eDMA transfer.
-
flexio_i2s_transfer_t queue[(4U)]
Transfer queue storing queued transfer.
-
size_t transferSize[(4U)]
Data bytes need to transfer
-
volatile uint8_t queueUser
Index for user to queue transfer.
-
volatile uint8_t queueDriver
Index for driver to get the transfer data and size
-
edma_handle_t *dmaHandle
FlexIO eDMA SPI Driver
-
status_t FLEXIO_SPI_MasterTransferCreateHandleEDMA(FLEXIO_SPI_Type *base, flexio_spi_master_edma_handle_t *handle, flexio_spi_master_edma_transfer_callback_t callback, void *userData, edma_handle_t *txHandle, edma_handle_t *rxHandle)
Initializes the FlexIO SPI master eDMA handle.
This function initializes the FlexIO SPI master eDMA handle which can be used for other FlexIO SPI master transactional APIs. For a specified FlexIO SPI instance, call this API once to get the initialized handle.
- Parameters:
base – Pointer to FLEXIO_SPI_Type structure.
handle – Pointer to flexio_spi_master_edma_handle_t structure to store the transfer state.
callback – SPI callback, NULL means no callback.
userData – callback function parameter.
txHandle – User requested eDMA handle for FlexIO SPI RX eDMA transfer.
rxHandle – User requested eDMA handle for FlexIO SPI TX eDMA transfer.
- Return values:
kStatus_Success – Successfully create the handle.
kStatus_OutOfRange – The FlexIO SPI eDMA type/handle table out of range.
-
status_t FLEXIO_SPI_MasterTransferEDMA(FLEXIO_SPI_Type *base, flexio_spi_master_edma_handle_t *handle, flexio_spi_transfer_t *xfer)
Performs a non-blocking FlexIO SPI transfer using eDMA.
Note
This interface returns immediately after transfer initiates. Call FLEXIO_SPI_MasterGetTransferCountEDMA to poll the transfer status and check whether the FlexIO SPI transfer is finished.
- Parameters:
base – Pointer to FLEXIO_SPI_Type structure.
handle – Pointer to flexio_spi_master_edma_handle_t structure to store the transfer state.
xfer – Pointer to FlexIO SPI transfer structure.
- Return values:
kStatus_Success – Successfully start a transfer.
kStatus_InvalidArgument – Input argument is invalid.
kStatus_FLEXIO_SPI_Busy – FlexIO SPI is not idle, is running another transfer.
-
void FLEXIO_SPI_MasterTransferAbortEDMA(FLEXIO_SPI_Type *base, flexio_spi_master_edma_handle_t *handle)
Aborts a FlexIO SPI transfer using eDMA.
- Parameters:
base – Pointer to FLEXIO_SPI_Type structure.
handle – FlexIO SPI eDMA handle pointer.
-
status_t FLEXIO_SPI_MasterTransferGetCountEDMA(FLEXIO_SPI_Type *base, flexio_spi_master_edma_handle_t *handle, size_t *count)
Gets the number of bytes transferred so far using FlexIO SPI master eDMA.
- Parameters:
base – Pointer to FLEXIO_SPI_Type structure.
handle – FlexIO SPI eDMA handle pointer.
count – Number of bytes transferred so far by the non-blocking transaction.
-
static inline void FLEXIO_SPI_SlaveTransferCreateHandleEDMA(FLEXIO_SPI_Type *base, flexio_spi_slave_edma_handle_t *handle, flexio_spi_slave_edma_transfer_callback_t callback, void *userData, edma_handle_t *txHandle, edma_handle_t *rxHandle)
Initializes the FlexIO SPI slave eDMA handle.
This function initializes the FlexIO SPI slave eDMA handle.
- Parameters:
base – Pointer to FLEXIO_SPI_Type structure.
handle – Pointer to flexio_spi_slave_edma_handle_t structure to store the transfer state.
callback – SPI callback, NULL means no callback.
userData – callback function parameter.
txHandle – User requested eDMA handle for FlexIO SPI TX eDMA transfer.
rxHandle – User requested eDMA handle for FlexIO SPI RX eDMA transfer.
-
status_t FLEXIO_SPI_SlaveTransferEDMA(FLEXIO_SPI_Type *base, flexio_spi_slave_edma_handle_t *handle, flexio_spi_transfer_t *xfer)
Performs a non-blocking FlexIO SPI transfer using eDMA.
Note
This interface returns immediately after transfer initiates. Call FLEXIO_SPI_SlaveGetTransferCountEDMA to poll the transfer status and check whether the FlexIO SPI transfer is finished.
- Parameters:
base – Pointer to FLEXIO_SPI_Type structure.
handle – Pointer to flexio_spi_slave_edma_handle_t structure to store the transfer state.
xfer – Pointer to FlexIO SPI transfer structure.
- Return values:
kStatus_Success – Successfully start a transfer.
kStatus_InvalidArgument – Input argument is invalid.
kStatus_FLEXIO_SPI_Busy – FlexIO SPI is not idle, is running another transfer.
-
static inline void FLEXIO_SPI_SlaveTransferAbortEDMA(FLEXIO_SPI_Type *base, flexio_spi_slave_edma_handle_t *handle)
Aborts a FlexIO SPI transfer using eDMA.
- Parameters:
base – Pointer to FLEXIO_SPI_Type structure.
handle – Pointer to flexio_spi_slave_edma_handle_t structure to store the transfer state.
-
static inline status_t FLEXIO_SPI_SlaveTransferGetCountEDMA(FLEXIO_SPI_Type *base, flexio_spi_slave_edma_handle_t *handle, size_t *count)
Gets the number of bytes transferred so far using FlexIO SPI slave eDMA.
- Parameters:
base – Pointer to FLEXIO_SPI_Type structure.
handle – FlexIO SPI eDMA handle pointer.
count – Number of bytes transferred so far by the non-blocking transaction.
-
FSL_FLEXIO_SPI_EDMA_DRIVER_VERSION
FlexIO SPI EDMA driver version.
-
typedef struct _flexio_spi_master_edma_handle flexio_spi_master_edma_handle_t
typedef for flexio_spi_master_edma_handle_t in advance.
-
typedef flexio_spi_master_edma_handle_t flexio_spi_slave_edma_handle_t
Slave handle is the same with master handle.
-
typedef void (*flexio_spi_master_edma_transfer_callback_t)(FLEXIO_SPI_Type *base, flexio_spi_master_edma_handle_t *handle, status_t status, void *userData)
FlexIO SPI master callback for finished transmit.
-
typedef void (*flexio_spi_slave_edma_transfer_callback_t)(FLEXIO_SPI_Type *base, flexio_spi_slave_edma_handle_t *handle, status_t status, void *userData)
FlexIO SPI slave callback for finished transmit.
-
struct _flexio_spi_master_edma_handle
- #include <fsl_flexio_spi_edma.h>
FlexIO SPI eDMA transfer handle, users should not touch the content of the handle.
Public Members
-
size_t transferSize
Total bytes to be transferred.
-
uint8_t nbytes
eDMA minor byte transfer count initially configured.
-
bool txInProgress
Send transfer in progress
-
bool rxInProgress
Receive transfer in progress
-
edma_handle_t *txHandle
DMA handler for SPI send
-
edma_handle_t *rxHandle
DMA handler for SPI receive
-
flexio_spi_master_edma_transfer_callback_t callback
Callback for SPI DMA transfer
-
void *userData
User Data for SPI DMA callback
-
size_t transferSize
FlexIO eDMA UART Driver
-
status_t FLEXIO_UART_TransferCreateHandleEDMA(FLEXIO_UART_Type *base, flexio_uart_edma_handle_t *handle, flexio_uart_edma_transfer_callback_t callback, void *userData, edma_handle_t *txEdmaHandle, edma_handle_t *rxEdmaHandle)
Initializes the UART handle which is used in transactional functions.
- Parameters:
base – Pointer to FLEXIO_UART_Type.
handle – Pointer to flexio_uart_edma_handle_t structure.
callback – The callback function.
userData – The parameter of the callback function.
rxEdmaHandle – User requested DMA handle for RX DMA transfer.
txEdmaHandle – User requested DMA handle for TX DMA transfer.
- Return values:
kStatus_Success – Successfully create the handle.
kStatus_OutOfRange – The FlexIO SPI eDMA type/handle table out of range.
-
status_t FLEXIO_UART_TransferSendEDMA(FLEXIO_UART_Type *base, flexio_uart_edma_handle_t *handle, flexio_uart_transfer_t *xfer)
Sends data using eDMA.
This function sends data using eDMA. This is a non-blocking function, which returns right away. When all data is sent out, the send callback function is called.
- Parameters:
base – Pointer to FLEXIO_UART_Type
handle – UART handle pointer.
xfer – UART eDMA transfer structure, see flexio_uart_transfer_t.
- Return values:
kStatus_Success – if succeed, others failed.
kStatus_FLEXIO_UART_TxBusy – Previous transfer on going.
-
status_t FLEXIO_UART_TransferReceiveEDMA(FLEXIO_UART_Type *base, flexio_uart_edma_handle_t *handle, flexio_uart_transfer_t *xfer)
Receives data using eDMA.
This function receives data using eDMA. This is a non-blocking function, which returns right away. When all data is received, the receive callback function is called.
- Parameters:
base – Pointer to FLEXIO_UART_Type
handle – Pointer to flexio_uart_edma_handle_t structure
xfer – UART eDMA transfer structure, see flexio_uart_transfer_t.
- Return values:
kStatus_Success – if succeed, others failed.
kStatus_UART_RxBusy – Previous transfer on going.
-
void FLEXIO_UART_TransferAbortSendEDMA(FLEXIO_UART_Type *base, flexio_uart_edma_handle_t *handle)
Aborts the sent data which using eDMA.
This function aborts sent data which using eDMA.
- Parameters:
base – Pointer to FLEXIO_UART_Type
handle – Pointer to flexio_uart_edma_handle_t structure
-
void FLEXIO_UART_TransferAbortReceiveEDMA(FLEXIO_UART_Type *base, flexio_uart_edma_handle_t *handle)
Aborts the receive data which using eDMA.
This function aborts the receive data which using eDMA.
- Parameters:
base – Pointer to FLEXIO_UART_Type
handle – Pointer to flexio_uart_edma_handle_t structure
-
status_t FLEXIO_UART_TransferGetSendCountEDMA(FLEXIO_UART_Type *base, flexio_uart_edma_handle_t *handle, size_t *count)
Gets the number of bytes sent out.
This function gets the number of bytes sent out.
- Parameters:
base – Pointer to FLEXIO_UART_Type
handle – Pointer to flexio_uart_edma_handle_t structure
count – Number of bytes sent so far by the non-blocking transaction.
- Return values:
kStatus_NoTransferInProgress – transfer has finished or no transfer in progress.
kStatus_Success – Successfully return the count.
-
status_t FLEXIO_UART_TransferGetReceiveCountEDMA(FLEXIO_UART_Type *base, flexio_uart_edma_handle_t *handle, size_t *count)
Gets the number of bytes received.
This function gets the number of bytes received.
- Parameters:
base – Pointer to FLEXIO_UART_Type
handle – Pointer to flexio_uart_edma_handle_t structure
count – Number of bytes received so far by the non-blocking transaction.
- Return values:
kStatus_NoTransferInProgress – transfer has finished or no transfer in progress.
kStatus_Success – Successfully return the count.
-
FSL_FLEXIO_UART_EDMA_DRIVER_VERSION
FlexIO UART EDMA driver version.
-
typedef struct _flexio_uart_edma_handle flexio_uart_edma_handle_t
-
typedef void (*flexio_uart_edma_transfer_callback_t)(FLEXIO_UART_Type *base, flexio_uart_edma_handle_t *handle, status_t status, void *userData)
UART transfer callback function.
-
struct _flexio_uart_edma_handle
- #include <fsl_flexio_uart_edma.h>
UART eDMA handle.
Public Members
-
flexio_uart_edma_transfer_callback_t callback
Callback function.
-
void *userData
UART callback function parameter.
-
size_t txDataSizeAll
Total bytes to be sent.
-
size_t rxDataSizeAll
Total bytes to be received.
-
edma_handle_t *txEdmaHandle
The eDMA TX channel used.
-
edma_handle_t *rxEdmaHandle
The eDMA RX channel used.
-
uint8_t nbytes
eDMA minor byte transfer count initially configured.
-
volatile uint8_t txState
TX transfer state.
-
volatile uint8_t rxState
RX transfer state
-
flexio_uart_edma_transfer_callback_t callback
FlexIO I2C Master Driver
-
status_t FLEXIO_I2C_CheckForBusyBus(FLEXIO_I2C_Type *base)
Make sure the bus isn’t already pulled down.
Check the FLEXIO pin status to see whether either of SDA and SCL pin is pulled down.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure..
- Return values:
kStatus_Success –
kStatus_FLEXIO_I2C_Busy –
-
status_t FLEXIO_I2C_MasterInit(FLEXIO_I2C_Type *base, flexio_i2c_master_config_t *masterConfig, uint32_t srcClock_Hz)
Ungates the FlexIO clock, resets the FlexIO module, and configures the FlexIO I2C hardware configuration.
Example
FLEXIO_I2C_Type base = { .flexioBase = FLEXIO, .SDAPinIndex = 0, .SCLPinIndex = 1, .shifterIndex = {0,1}, .timerIndex = {0,1} }; flexio_i2c_master_config_t config = { .enableInDoze = false, .enableInDebug = true, .enableFastAccess = false, .baudRate_Bps = 100000 }; FLEXIO_I2C_MasterInit(base, &config, srcClock_Hz);
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
masterConfig – Pointer to flexio_i2c_master_config_t structure.
srcClock_Hz – FlexIO source clock in Hz.
- Return values:
kStatus_Success – Initialization successful
kStatus_InvalidArgument – The source clock exceed upper range limitation
-
void FLEXIO_I2C_MasterDeinit(FLEXIO_I2C_Type *base)
De-initializes the FlexIO I2C master peripheral. Calling this API Resets the FlexIO I2C master shifer and timer config, module can’t work unless the FLEXIO_I2C_MasterInit is called.
- Parameters:
base – pointer to FLEXIO_I2C_Type structure.
-
void FLEXIO_I2C_MasterGetDefaultConfig(flexio_i2c_master_config_t *masterConfig)
Gets the default configuration to configure the FlexIO module. The configuration can be used directly for calling the FLEXIO_I2C_MasterInit().
Example:
flexio_i2c_master_config_t config; FLEXIO_I2C_MasterGetDefaultConfig(&config);
- Parameters:
masterConfig – Pointer to flexio_i2c_master_config_t structure.
-
static inline void FLEXIO_I2C_MasterEnable(FLEXIO_I2C_Type *base, bool enable)
Enables/disables the FlexIO module operation.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
enable – Pass true to enable module, false does not have any effect.
-
uint32_t FLEXIO_I2C_MasterGetStatusFlags(FLEXIO_I2C_Type *base)
Gets the FlexIO I2C master status flags.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure
- Returns:
Status flag, use status flag to AND _flexio_i2c_master_status_flags can get the related status.
-
void FLEXIO_I2C_MasterClearStatusFlags(FLEXIO_I2C_Type *base, uint32_t mask)
Clears the FlexIO I2C master status flags.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
mask – Status flag. The parameter can be any combination of the following values:
kFLEXIO_I2C_RxFullFlag
kFLEXIO_I2C_ReceiveNakFlag
-
void FLEXIO_I2C_MasterEnableInterrupts(FLEXIO_I2C_Type *base, uint32_t mask)
Enables the FlexIO i2c master interrupt requests.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
mask – Interrupt source. Currently only one interrupt request source:
kFLEXIO_I2C_TransferCompleteInterruptEnable
-
void FLEXIO_I2C_MasterDisableInterrupts(FLEXIO_I2C_Type *base, uint32_t mask)
Disables the FlexIO I2C master interrupt requests.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
mask – Interrupt source.
-
void FLEXIO_I2C_MasterSetBaudRate(FLEXIO_I2C_Type *base, uint32_t baudRate_Bps, uint32_t srcClock_Hz)
Sets the FlexIO I2C master transfer baudrate.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure
baudRate_Bps – the baud rate value in HZ
srcClock_Hz – source clock in HZ
-
void FLEXIO_I2C_MasterStart(FLEXIO_I2C_Type *base, uint8_t address, flexio_i2c_direction_t direction)
Sends START + 7-bit address to the bus.
Note
This API should be called when the transfer configuration is ready to send a START signal and 7-bit address to the bus. This is a non-blocking API, which returns directly after the address is put into the data register but the address transfer is not finished on the bus. Ensure that the kFLEXIO_I2C_RxFullFlag status is asserted before calling this API.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
address – 7-bit address.
direction – transfer direction. This parameter is one of the values in flexio_i2c_direction_t:
kFLEXIO_I2C_Write: Transmit
kFLEXIO_I2C_Read: Receive
-
void FLEXIO_I2C_MasterStop(FLEXIO_I2C_Type *base)
Sends the stop signal on the bus.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
-
void FLEXIO_I2C_MasterRepeatedStart(FLEXIO_I2C_Type *base)
Sends the repeated start signal on the bus.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
-
void FLEXIO_I2C_MasterAbortStop(FLEXIO_I2C_Type *base)
Sends the stop signal when transfer is still on-going.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
-
void FLEXIO_I2C_MasterEnableAck(FLEXIO_I2C_Type *base, bool enable)
Configures the sent ACK/NAK for the following byte.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
enable – True to configure send ACK, false configure to send NAK.
-
status_t FLEXIO_I2C_MasterSetTransferCount(FLEXIO_I2C_Type *base, uint16_t count)
Sets the number of bytes to be transferred from a start signal to a stop signal.
Note
Call this API before a transfer begins because the timer generates a number of clocks according to the number of bytes that need to be transferred.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
count – Number of bytes need to be transferred from a start signal to a re-start/stop signal
- Return values:
kStatus_Success – Successfully configured the count.
kStatus_InvalidArgument – Input argument is invalid.
-
static inline void FLEXIO_I2C_MasterWriteByte(FLEXIO_I2C_Type *base, uint32_t data)
Writes one byte of data to the I2C bus.
Note
This is a non-blocking API, which returns directly after the data is put into the data register but the data transfer is not finished on the bus. Ensure that the TxEmptyFlag is asserted before calling this API.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
data – a byte of data.
-
static inline uint8_t FLEXIO_I2C_MasterReadByte(FLEXIO_I2C_Type *base)
Reads one byte of data from the I2C bus.
Note
This is a non-blocking API, which returns directly after the data is read from the data register. Ensure that the data is ready in the register.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
- Returns:
data byte read.
-
status_t FLEXIO_I2C_MasterWriteBlocking(FLEXIO_I2C_Type *base, const uint8_t *txBuff, uint8_t txSize)
Sends a buffer of data in bytes.
Note
This function blocks via polling until all bytes have been sent.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
txBuff – The data bytes to send.
txSize – The number of data bytes to send.
- Return values:
kStatus_Success – Successfully write data.
kStatus_FLEXIO_I2C_Nak – Receive NAK during writing data.
kStatus_FLEXIO_I2C_Timeout – Timeout polling status flags.
-
status_t FLEXIO_I2C_MasterReadBlocking(FLEXIO_I2C_Type *base, uint8_t *rxBuff, uint8_t rxSize)
Receives a buffer of bytes.
Note
This function blocks via polling until all bytes have been received.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
rxBuff – The buffer to store the received bytes.
rxSize – The number of data bytes to be received.
- Return values:
kStatus_Success – Successfully read data.
kStatus_FLEXIO_I2C_Timeout – Timeout polling status flags.
-
status_t FLEXIO_I2C_MasterTransferBlocking(FLEXIO_I2C_Type *base, flexio_i2c_master_transfer_t *xfer)
Performs a master polling transfer on the I2C bus.
Note
The API does not return until the transfer succeeds or fails due to receiving NAK.
- Parameters:
base – pointer to FLEXIO_I2C_Type structure.
xfer – pointer to flexio_i2c_master_transfer_t structure.
- Returns:
status of status_t.
-
status_t FLEXIO_I2C_MasterTransferCreateHandle(FLEXIO_I2C_Type *base, flexio_i2c_master_handle_t *handle, flexio_i2c_master_transfer_callback_t callback, void *userData)
Initializes the I2C handle which is used in transactional functions.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
handle – Pointer to flexio_i2c_master_handle_t structure to store the transfer state.
callback – Pointer to user callback function.
userData – User param passed to the callback function.
- Return values:
kStatus_Success – Successfully create the handle.
kStatus_OutOfRange – The FlexIO type/handle/isr table out of range.
-
status_t FLEXIO_I2C_MasterTransferNonBlocking(FLEXIO_I2C_Type *base, flexio_i2c_master_handle_t *handle, flexio_i2c_master_transfer_t *xfer)
Performs a master interrupt non-blocking transfer on the I2C bus.
Note
The API returns immediately after the transfer initiates. Call FLEXIO_I2C_MasterTransferGetCount to poll the transfer status to check whether the transfer is finished. If the return status is not kStatus_FLEXIO_I2C_Busy, the transfer is finished.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure
handle – Pointer to flexio_i2c_master_handle_t structure which stores the transfer state
xfer – pointer to flexio_i2c_master_transfer_t structure
- Return values:
kStatus_Success – Successfully start a transfer.
kStatus_FLEXIO_I2C_Busy – FlexIO I2C is not idle, is running another transfer.
-
status_t FLEXIO_I2C_MasterTransferGetCount(FLEXIO_I2C_Type *base, flexio_i2c_master_handle_t *handle, size_t *count)
Gets the master transfer status during a interrupt non-blocking transfer.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure.
handle – Pointer to flexio_i2c_master_handle_t structure which stores the transfer state.
count – Number of bytes transferred so far by the non-blocking transaction.
- Return values:
kStatus_InvalidArgument – count is Invalid.
kStatus_NoTransferInProgress – There is not a non-blocking transaction currently in progress.
kStatus_Success – Successfully return the count.
-
void FLEXIO_I2C_MasterTransferAbort(FLEXIO_I2C_Type *base, flexio_i2c_master_handle_t *handle)
Aborts an interrupt non-blocking transfer early.
Note
This API can be called at any time when an interrupt non-blocking transfer initiates to abort the transfer early.
- Parameters:
base – Pointer to FLEXIO_I2C_Type structure
handle – Pointer to flexio_i2c_master_handle_t structure which stores the transfer state
-
void FLEXIO_I2C_MasterTransferHandleIRQ(void *i2cType, void *i2cHandle)
Master interrupt handler.
- Parameters:
i2cType – Pointer to FLEXIO_I2C_Type structure
i2cHandle – Pointer to flexio_i2c_master_transfer_t structure
-
FSL_FLEXIO_I2C_MASTER_DRIVER_VERSION
FlexIO I2C transfer status.
Values:
-
enumerator kStatus_FLEXIO_I2C_Busy
I2C is busy doing transfer.
-
enumerator kStatus_FLEXIO_I2C_Idle
I2C is busy doing transfer.
-
enumerator kStatus_FLEXIO_I2C_Nak
NAK received during transfer.
-
enumerator kStatus_FLEXIO_I2C_Timeout
Timeout polling status flags.
-
enumerator kStatus_FLEXIO_I2C_Busy
-
enum _flexio_i2c_master_interrupt
Define FlexIO I2C master interrupt mask.
Values:
-
enumerator kFLEXIO_I2C_TxEmptyInterruptEnable
Tx buffer empty interrupt enable.
-
enumerator kFLEXIO_I2C_RxFullInterruptEnable
Rx buffer full interrupt enable.
-
enumerator kFLEXIO_I2C_TxEmptyInterruptEnable
-
enum _flexio_i2c_master_status_flags
Define FlexIO I2C master status mask.
Values:
-
enumerator kFLEXIO_I2C_TxEmptyFlag
Tx shifter empty flag.
-
enumerator kFLEXIO_I2C_RxFullFlag
Rx shifter full/Transfer complete flag.
-
enumerator kFLEXIO_I2C_ReceiveNakFlag
Receive NAK flag.
-
enumerator kFLEXIO_I2C_TxEmptyFlag
-
enum _flexio_i2c_direction
Direction of master transfer.
Values:
-
enumerator kFLEXIO_I2C_Write
Master send to slave.
-
enumerator kFLEXIO_I2C_Read
Master receive from slave.
-
enumerator kFLEXIO_I2C_Write
-
typedef enum _flexio_i2c_direction flexio_i2c_direction_t
Direction of master transfer.
-
typedef struct _flexio_i2c_type FLEXIO_I2C_Type
Define FlexIO I2C master access structure typedef.
-
typedef struct _flexio_i2c_master_config flexio_i2c_master_config_t
Define FlexIO I2C master user configuration structure.
-
typedef struct _flexio_i2c_master_transfer flexio_i2c_master_transfer_t
Define FlexIO I2C master transfer structure.
-
typedef struct _flexio_i2c_master_handle flexio_i2c_master_handle_t
FlexIO I2C master handle typedef.
-
typedef void (*flexio_i2c_master_transfer_callback_t)(FLEXIO_I2C_Type *base, flexio_i2c_master_handle_t *handle, status_t status, void *userData)
FlexIO I2C master transfer callback typedef.
-
I2C_RETRY_TIMES
Retry times for waiting flag.
-
struct _flexio_i2c_type
- #include <fsl_flexio_i2c_master.h>
Define FlexIO I2C master access structure typedef.
Public Members
-
FLEXIO_Type *flexioBase
FlexIO base pointer.
-
uint8_t SDAPinIndex
Pin select for I2C SDA.
-
uint8_t SCLPinIndex
Pin select for I2C SCL.
-
uint8_t shifterIndex[2]
Shifter index used in FlexIO I2C.
-
uint8_t timerIndex[3]
Timer index used in FlexIO I2C.
-
uint32_t baudrate
Master transfer baudrate, used to calculate delay time.
-
FLEXIO_Type *flexioBase
-
struct _flexio_i2c_master_config
- #include <fsl_flexio_i2c_master.h>
Define FlexIO I2C master user configuration structure.
Public Members
-
bool enableMaster
Enables the FlexIO I2C peripheral at initialization time.
-
bool enableInDoze
Enable/disable FlexIO operation in doze mode.
-
bool enableInDebug
Enable/disable FlexIO operation in debug mode.
-
bool enableFastAccess
Enable/disable fast access to FlexIO registers, fast access requires the FlexIO clock to be at least twice the frequency of the bus clock.
-
uint32_t baudRate_Bps
Baud rate in Bps.
-
bool enableMaster
-
struct _flexio_i2c_master_transfer
- #include <fsl_flexio_i2c_master.h>
Define FlexIO I2C master transfer structure.
Public Members
-
uint32_t flags
Transfer flag which controls the transfer, reserved for FlexIO I2C.
-
uint8_t slaveAddress
7-bit slave address.
-
flexio_i2c_direction_t direction
Transfer direction, read or write.
-
uint32_t subaddress
Sub address. Transferred MSB first.
-
uint8_t subaddressSize
Size of command buffer.
-
uint8_t volatile *data
Transfer buffer.
-
volatile size_t dataSize
Transfer size.
-
uint32_t flags
-
struct _flexio_i2c_master_handle
- #include <fsl_flexio_i2c_master.h>
Define FlexIO I2C master handle structure.
Public Members
-
flexio_i2c_master_transfer_t transfer
FlexIO I2C master transfer copy.
-
size_t transferSize
Total bytes to be transferred.
-
uint8_t state
Transfer state maintained during transfer.
-
flexio_i2c_master_transfer_callback_t completionCallback
Callback function called at transfer event. Callback function called at transfer event.
-
void *userData
Callback parameter passed to callback function.
-
bool needRestart
Whether master needs to send re-start signal.
-
flexio_i2c_master_transfer_t transfer
FlexIO I2S Driver
-
void FLEXIO_I2S_Init(FLEXIO_I2S_Type *base, const flexio_i2s_config_t *config)
Initializes the FlexIO I2S.
This API configures FlexIO pins and shifter to I2S and configures the FlexIO I2S with a configuration structure. The configuration structure can be filled by the user, or be set with default values by FLEXIO_I2S_GetDefaultConfig().
Note
This API should be called at the beginning of the application to use the FlexIO I2S driver. Otherwise, any access to the FlexIO I2S module can cause hard fault because the clock is not enabled.
- Parameters:
base – FlexIO I2S base pointer
config – FlexIO I2S configure structure.
-
void FLEXIO_I2S_GetDefaultConfig(flexio_i2s_config_t *config)
Sets the FlexIO I2S configuration structure to default values.
The purpose of this API is to get the configuration structure initialized for use in FLEXIO_I2S_Init(). Users may use the initialized structure unchanged in FLEXIO_I2S_Init() or modify some fields of the structure before calling FLEXIO_I2S_Init().
- Parameters:
config – pointer to master configuration structure
-
void FLEXIO_I2S_Deinit(FLEXIO_I2S_Type *base)
De-initializes the FlexIO I2S.
Calling this API resets the FlexIO I2S shifter and timer config. After calling this API, call the FLEXO_I2S_Init to use the FlexIO I2S module.
- Parameters:
base – FlexIO I2S base pointer
-
static inline void FLEXIO_I2S_Enable(FLEXIO_I2S_Type *base, bool enable)
Enables/disables the FlexIO I2S module operation.
- Parameters:
base – Pointer to FLEXIO_I2S_Type
enable – True to enable, false dose not have any effect.
-
uint32_t FLEXIO_I2S_GetStatusFlags(FLEXIO_I2S_Type *base)
Gets the FlexIO I2S status flags.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure
- Returns:
Status flag, which are ORed by the enumerators in the _flexio_i2s_status_flags.
-
void FLEXIO_I2S_EnableInterrupts(FLEXIO_I2S_Type *base, uint32_t mask)
Enables the FlexIO I2S interrupt.
This function enables the FlexIO UART interrupt.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure
mask – interrupt source
-
void FLEXIO_I2S_DisableInterrupts(FLEXIO_I2S_Type *base, uint32_t mask)
Disables the FlexIO I2S interrupt.
This function enables the FlexIO UART interrupt.
- Parameters:
base – pointer to FLEXIO_I2S_Type structure
mask – interrupt source
-
static inline void FLEXIO_I2S_TxEnableDMA(FLEXIO_I2S_Type *base, bool enable)
Enables/disables the FlexIO I2S Tx DMA requests.
- Parameters:
base – FlexIO I2S base pointer
enable – True means enable DMA, false means disable DMA.
-
static inline void FLEXIO_I2S_RxEnableDMA(FLEXIO_I2S_Type *base, bool enable)
Enables/disables the FlexIO I2S Rx DMA requests.
- Parameters:
base – FlexIO I2S base pointer
enable – True means enable DMA, false means disable DMA.
-
static inline uint32_t FLEXIO_I2S_TxGetDataRegisterAddress(FLEXIO_I2S_Type *base)
Gets the FlexIO I2S send data register address.
This function returns the I2S data register address, mainly used by DMA/eDMA.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure
- Returns:
FlexIO i2s send data register address.
-
static inline uint32_t FLEXIO_I2S_RxGetDataRegisterAddress(FLEXIO_I2S_Type *base)
Gets the FlexIO I2S receive data register address.
This function returns the I2S data register address, mainly used by DMA/eDMA.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure
- Returns:
FlexIO i2s receive data register address.
-
void FLEXIO_I2S_MasterSetFormat(FLEXIO_I2S_Type *base, flexio_i2s_format_t *format, uint32_t srcClock_Hz)
Configures the FlexIO I2S audio format in master mode.
Audio format can be changed in run-time of FlexIO I2S. This function configures the sample rate and audio data format to be transferred.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure
format – Pointer to FlexIO I2S audio data format structure.
srcClock_Hz – I2S master clock source frequency in Hz.
-
void FLEXIO_I2S_SlaveSetFormat(FLEXIO_I2S_Type *base, flexio_i2s_format_t *format)
Configures the FlexIO I2S audio format in slave mode.
Audio format can be changed in run-time of FlexIO I2S. This function configures the sample rate and audio data format to be transferred.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure
format – Pointer to FlexIO I2S audio data format structure.
-
status_t FLEXIO_I2S_WriteBlocking(FLEXIO_I2S_Type *base, uint8_t bitWidth, uint8_t *txData, size_t size)
Sends data using a blocking method.
Note
This function blocks via polling until data is ready to be sent.
- Parameters:
base – FlexIO I2S base pointer.
bitWidth – How many bits in a audio word, usually 8/16/24/32 bits.
txData – Pointer to the data to be written.
size – Bytes to be written.
- Return values:
kStatus_Success – Successfully write data.
kStatus_FLEXIO_I2C_Timeout – Timeout polling status flags.
-
static inline void FLEXIO_I2S_WriteData(FLEXIO_I2S_Type *base, uint8_t bitWidth, uint32_t data)
Writes data into a data register.
- Parameters:
base – FlexIO I2S base pointer.
bitWidth – How many bits in a audio word, usually 8/16/24/32 bits.
data – Data to be written.
-
status_t FLEXIO_I2S_ReadBlocking(FLEXIO_I2S_Type *base, uint8_t bitWidth, uint8_t *rxData, size_t size)
Receives a piece of data using a blocking method.
Note
This function blocks via polling until data is ready to be sent.
- Parameters:
base – FlexIO I2S base pointer
bitWidth – How many bits in a audio word, usually 8/16/24/32 bits.
rxData – Pointer to the data to be read.
size – Bytes to be read.
- Return values:
kStatus_Success – Successfully read data.
kStatus_FLEXIO_I2C_Timeout – Timeout polling status flags.
-
static inline uint32_t FLEXIO_I2S_ReadData(FLEXIO_I2S_Type *base)
Reads a data from the data register.
- Parameters:
base – FlexIO I2S base pointer
- Returns:
Data read from data register.
-
void FLEXIO_I2S_TransferTxCreateHandle(FLEXIO_I2S_Type *base, flexio_i2s_handle_t *handle, flexio_i2s_callback_t callback, void *userData)
Initializes the FlexIO I2S handle.
This function initializes the FlexIO I2S handle which can be used for other FlexIO I2S transactional APIs. Call this API once to get the initialized handle.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure
handle – Pointer to flexio_i2s_handle_t structure to store the transfer state.
callback – FlexIO I2S callback function, which is called while finished a block.
userData – User parameter for the FlexIO I2S callback.
-
void FLEXIO_I2S_TransferSetFormat(FLEXIO_I2S_Type *base, flexio_i2s_handle_t *handle, flexio_i2s_format_t *format, uint32_t srcClock_Hz)
Configures the FlexIO I2S audio format.
Audio format can be changed at run-time of FlexIO I2S. This function configures the sample rate and audio data format to be transferred.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure.
handle – FlexIO I2S handle pointer.
format – Pointer to audio data format structure.
srcClock_Hz – FlexIO I2S bit clock source frequency in Hz. This parameter should be 0 while in slave mode.
-
void FLEXIO_I2S_TransferRxCreateHandle(FLEXIO_I2S_Type *base, flexio_i2s_handle_t *handle, flexio_i2s_callback_t callback, void *userData)
Initializes the FlexIO I2S receive handle.
This function initializes the FlexIO I2S handle which can be used for other FlexIO I2S transactional APIs. Call this API once to get the initialized handle.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure.
handle – Pointer to flexio_i2s_handle_t structure to store the transfer state.
callback – FlexIO I2S callback function, which is called while finished a block.
userData – User parameter for the FlexIO I2S callback.
-
status_t FLEXIO_I2S_TransferSendNonBlocking(FLEXIO_I2S_Type *base, flexio_i2s_handle_t *handle, flexio_i2s_transfer_t *xfer)
Performs an interrupt non-blocking send transfer on FlexIO I2S.
Note
The API returns immediately after transfer initiates. Call FLEXIO_I2S_GetRemainingBytes to poll the transfer status and check whether the transfer is finished. If the return status is 0, the transfer is finished.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure.
handle – Pointer to flexio_i2s_handle_t structure which stores the transfer state
xfer – Pointer to flexio_i2s_transfer_t structure
- Return values:
kStatus_Success – Successfully start the data transmission.
kStatus_FLEXIO_I2S_TxBusy – Previous transmission still not finished, data not all written to TX register yet.
kStatus_InvalidArgument – The input parameter is invalid.
-
status_t FLEXIO_I2S_TransferReceiveNonBlocking(FLEXIO_I2S_Type *base, flexio_i2s_handle_t *handle, flexio_i2s_transfer_t *xfer)
Performs an interrupt non-blocking receive transfer on FlexIO I2S.
Note
The API returns immediately after transfer initiates. Call FLEXIO_I2S_GetRemainingBytes to poll the transfer status to check whether the transfer is finished. If the return status is 0, the transfer is finished.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure.
handle – Pointer to flexio_i2s_handle_t structure which stores the transfer state
xfer – Pointer to flexio_i2s_transfer_t structure
- Return values:
kStatus_Success – Successfully start the data receive.
kStatus_FLEXIO_I2S_RxBusy – Previous receive still not finished.
kStatus_InvalidArgument – The input parameter is invalid.
-
void FLEXIO_I2S_TransferAbortSend(FLEXIO_I2S_Type *base, flexio_i2s_handle_t *handle)
Aborts the current send.
Note
This API can be called at any time when interrupt non-blocking transfer initiates to abort the transfer in a early time.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure.
handle – Pointer to flexio_i2s_handle_t structure which stores the transfer state
-
void FLEXIO_I2S_TransferAbortReceive(FLEXIO_I2S_Type *base, flexio_i2s_handle_t *handle)
Aborts the current receive.
Note
This API can be called at any time when interrupt non-blocking transfer initiates to abort the transfer in a early time.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure.
handle – Pointer to flexio_i2s_handle_t structure which stores the transfer state
-
status_t FLEXIO_I2S_TransferGetSendCount(FLEXIO_I2S_Type *base, flexio_i2s_handle_t *handle, size_t *count)
Gets the remaining bytes to be sent.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure.
handle – Pointer to flexio_i2s_handle_t structure which stores the transfer state
count – Bytes sent.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is not a non-blocking transaction currently in progress.
-
status_t FLEXIO_I2S_TransferGetReceiveCount(FLEXIO_I2S_Type *base, flexio_i2s_handle_t *handle, size_t *count)
Gets the remaining bytes to be received.
- Parameters:
base – Pointer to FLEXIO_I2S_Type structure.
handle – Pointer to flexio_i2s_handle_t structure which stores the transfer state
count – Bytes recieved.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is not a non-blocking transaction currently in progress.
- Returns:
count Bytes received.
-
void FLEXIO_I2S_TransferTxHandleIRQ(void *i2sBase, void *i2sHandle)
Tx interrupt handler.
- Parameters:
i2sBase – Pointer to FLEXIO_I2S_Type structure.
i2sHandle – Pointer to flexio_i2s_handle_t structure
-
void FLEXIO_I2S_TransferRxHandleIRQ(void *i2sBase, void *i2sHandle)
Rx interrupt handler.
- Parameters:
i2sBase – Pointer to FLEXIO_I2S_Type structure.
i2sHandle – Pointer to flexio_i2s_handle_t structure.
-
FSL_FLEXIO_I2S_DRIVER_VERSION
FlexIO I2S driver version 2.2.0.
FlexIO I2S transfer status.
Values:
-
enumerator kStatus_FLEXIO_I2S_Idle
FlexIO I2S is in idle state
-
enumerator kStatus_FLEXIO_I2S_TxBusy
FlexIO I2S Tx is busy
-
enumerator kStatus_FLEXIO_I2S_RxBusy
FlexIO I2S Tx is busy
-
enumerator kStatus_FLEXIO_I2S_Error
FlexIO I2S error occurred
-
enumerator kStatus_FLEXIO_I2S_QueueFull
FlexIO I2S transfer queue is full.
-
enumerator kStatus_FLEXIO_I2S_Timeout
FlexIO I2S timeout polling status flags.
-
enumerator kStatus_FLEXIO_I2S_Idle
-
enum _flexio_i2s_master_slave
Master or slave mode.
Values:
-
enumerator kFLEXIO_I2S_Master
Master mode
-
enumerator kFLEXIO_I2S_Slave
Slave mode
-
enumerator kFLEXIO_I2S_Master
_flexio_i2s_interrupt_enable Define FlexIO FlexIO I2S interrupt mask.
Values:
-
enumerator kFLEXIO_I2S_TxDataRegEmptyInterruptEnable
Transmit buffer empty interrupt enable.
-
enumerator kFLEXIO_I2S_RxDataRegFullInterruptEnable
Receive buffer full interrupt enable.
-
enumerator kFLEXIO_I2S_TxDataRegEmptyInterruptEnable
_flexio_i2s_status_flags Define FlexIO FlexIO I2S status mask.
Values:
-
enumerator kFLEXIO_I2S_TxDataRegEmptyFlag
Transmit buffer empty flag.
-
enumerator kFLEXIO_I2S_RxDataRegFullFlag
Receive buffer full flag.
-
enumerator kFLEXIO_I2S_TxDataRegEmptyFlag
-
enum _flexio_i2s_sample_rate
Audio sample rate.
Values:
-
enumerator kFLEXIO_I2S_SampleRate8KHz
Sample rate 8000Hz
-
enumerator kFLEXIO_I2S_SampleRate11025Hz
Sample rate 11025Hz
-
enumerator kFLEXIO_I2S_SampleRate12KHz
Sample rate 12000Hz
-
enumerator kFLEXIO_I2S_SampleRate16KHz
Sample rate 16000Hz
-
enumerator kFLEXIO_I2S_SampleRate22050Hz
Sample rate 22050Hz
-
enumerator kFLEXIO_I2S_SampleRate24KHz
Sample rate 24000Hz
-
enumerator kFLEXIO_I2S_SampleRate32KHz
Sample rate 32000Hz
-
enumerator kFLEXIO_I2S_SampleRate44100Hz
Sample rate 44100Hz
-
enumerator kFLEXIO_I2S_SampleRate48KHz
Sample rate 48000Hz
-
enumerator kFLEXIO_I2S_SampleRate96KHz
Sample rate 96000Hz
-
enumerator kFLEXIO_I2S_SampleRate8KHz
-
enum _flexio_i2s_word_width
Audio word width.
Values:
-
enumerator kFLEXIO_I2S_WordWidth8bits
Audio data width 8 bits
-
enumerator kFLEXIO_I2S_WordWidth16bits
Audio data width 16 bits
-
enumerator kFLEXIO_I2S_WordWidth24bits
Audio data width 24 bits
-
enumerator kFLEXIO_I2S_WordWidth32bits
Audio data width 32 bits
-
enumerator kFLEXIO_I2S_WordWidth8bits
-
typedef struct _flexio_i2s_type FLEXIO_I2S_Type
Define FlexIO I2S access structure typedef.
-
typedef enum _flexio_i2s_master_slave flexio_i2s_master_slave_t
Master or slave mode.
-
typedef struct _flexio_i2s_config flexio_i2s_config_t
FlexIO I2S configure structure.
-
typedef struct _flexio_i2s_format flexio_i2s_format_t
FlexIO I2S audio format, FlexIO I2S only support the same format in Tx and Rx.
-
typedef enum _flexio_i2s_sample_rate flexio_i2s_sample_rate_t
Audio sample rate.
-
typedef enum _flexio_i2s_word_width flexio_i2s_word_width_t
Audio word width.
-
typedef struct _flexio_i2s_transfer flexio_i2s_transfer_t
Define FlexIO I2S transfer structure.
-
typedef struct _flexio_i2s_handle flexio_i2s_handle_t
-
typedef void (*flexio_i2s_callback_t)(FLEXIO_I2S_Type *base, flexio_i2s_handle_t *handle, status_t status, void *userData)
FlexIO I2S xfer callback prototype.
-
I2S_RETRY_TIMES
Retry times for waiting flag.
-
FLEXIO_I2S_XFER_QUEUE_SIZE
FlexIO I2S transfer queue size, user can refine it according to use case.
-
struct _flexio_i2s_type
- #include <fsl_flexio_i2s.h>
Define FlexIO I2S access structure typedef.
Public Members
-
FLEXIO_Type *flexioBase
FlexIO base pointer
-
uint8_t txPinIndex
Tx data pin index in FlexIO pins
-
uint8_t rxPinIndex
Rx data pin index
-
uint8_t bclkPinIndex
Bit clock pin index
-
uint8_t fsPinIndex
Frame sync pin index
-
uint8_t txShifterIndex
Tx data shifter index
-
uint8_t rxShifterIndex
Rx data shifter index
-
uint8_t bclkTimerIndex
Bit clock timer index
-
uint8_t fsTimerIndex
Frame sync timer index
-
FLEXIO_Type *flexioBase
-
struct _flexio_i2s_config
- #include <fsl_flexio_i2s.h>
FlexIO I2S configure structure.
Public Members
-
bool enableI2S
Enable FlexIO I2S
-
flexio_i2s_master_slave_t masterSlave
Master or slave
-
flexio_pin_polarity_t txPinPolarity
Tx data pin polarity, active high or low
-
flexio_pin_polarity_t rxPinPolarity
Rx data pin polarity
-
flexio_pin_polarity_t bclkPinPolarity
Bit clock pin polarity
-
flexio_pin_polarity_t fsPinPolarity
Frame sync pin polarity
-
flexio_shifter_timer_polarity_t txTimerPolarity
Tx data valid on bclk rising or falling edge
-
flexio_shifter_timer_polarity_t rxTimerPolarity
Rx data valid on bclk rising or falling edge
-
bool enableI2S
-
struct _flexio_i2s_format
- #include <fsl_flexio_i2s.h>
FlexIO I2S audio format, FlexIO I2S only support the same format in Tx and Rx.
Public Members
-
uint8_t bitWidth
Bit width of audio data, always 8/16/24/32 bits
-
uint32_t sampleRate_Hz
Sample rate of the audio data
-
uint8_t bitWidth
-
struct _flexio_i2s_transfer
- #include <fsl_flexio_i2s.h>
Define FlexIO I2S transfer structure.
Public Members
-
uint8_t *data
Data buffer start pointer
-
size_t dataSize
Bytes to be transferred.
-
uint8_t *data
-
struct _flexio_i2s_handle
- #include <fsl_flexio_i2s.h>
Define FlexIO I2S handle structure.
Public Members
-
uint32_t state
Internal state
-
flexio_i2s_callback_t callback
Callback function called at transfer event
-
void *userData
Callback parameter passed to callback function
-
uint8_t bitWidth
Bit width for transfer, 8/16/24/32bits
-
flexio_i2s_transfer_t queue[(4U)]
Transfer queue storing queued transfer
-
size_t transferSize[(4U)]
Data bytes need to transfer
-
volatile uint8_t queueUser
Index for user to queue transfer
-
volatile uint8_t queueDriver
Index for driver to get the transfer data and size
-
uint32_t state
FlexIO SPI Driver
-
void FLEXIO_SPI_MasterInit(FLEXIO_SPI_Type *base, flexio_spi_master_config_t *masterConfig, uint32_t srcClock_Hz)
Ungates the FlexIO clock, resets the FlexIO module, configures the FlexIO SPI master hardware, and configures the FlexIO SPI with FlexIO SPI master configuration. The configuration structure can be filled by the user, or be set with default values by the FLEXIO_SPI_MasterGetDefaultConfig().
Example
FLEXIO_SPI_Type spiDev = { .flexioBase = FLEXIO, .SDOPinIndex = 0, .SDIPinIndex = 1, .SCKPinIndex = 2, .CSnPinIndex = 3, .shifterIndex = {0,1}, .timerIndex = {0,1} }; flexio_spi_master_config_t config = { .enableMaster = true, .enableInDoze = false, .enableInDebug = true, .enableFastAccess = false, .baudRate_Bps = 500000, .phase = kFLEXIO_SPI_ClockPhaseFirstEdge, .direction = kFLEXIO_SPI_MsbFirst, .dataMode = kFLEXIO_SPI_8BitMode }; FLEXIO_SPI_MasterInit(&spiDev, &config, srcClock_Hz);
Note
1.FlexIO SPI master only support CPOL = 0, which means clock inactive low. 2.For FlexIO SPI master, the input valid time is 1.5 clock cycles, for slave the output valid time is 2.5 clock cycles. So if FlexIO SPI master communicates with other spi IPs, the maximum baud rate is FlexIO clock frequency divided by 2*2=4. If FlexIO SPI master communicates with FlexIO SPI slave, the maximum baud rate is FlexIO clock frequency divided by (1.5+2.5)*2=8.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
masterConfig – Pointer to the flexio_spi_master_config_t structure.
srcClock_Hz – FlexIO source clock in Hz.
-
void FLEXIO_SPI_MasterDeinit(FLEXIO_SPI_Type *base)
Resets the FlexIO SPI timer and shifter config.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type.
-
void FLEXIO_SPI_MasterGetDefaultConfig(flexio_spi_master_config_t *masterConfig)
Gets the default configuration to configure the FlexIO SPI master. The configuration can be used directly by calling the FLEXIO_SPI_MasterConfigure(). Example:
flexio_spi_master_config_t masterConfig; FLEXIO_SPI_MasterGetDefaultConfig(&masterConfig);
- Parameters:
masterConfig – Pointer to the flexio_spi_master_config_t structure.
-
void FLEXIO_SPI_SlaveInit(FLEXIO_SPI_Type *base, flexio_spi_slave_config_t *slaveConfig)
Ungates the FlexIO clock, resets the FlexIO module, configures the FlexIO SPI slave hardware configuration, and configures the FlexIO SPI with FlexIO SPI slave configuration. The configuration structure can be filled by the user, or be set with default values by the FLEXIO_SPI_SlaveGetDefaultConfig().
Note
1.Only one timer is needed in the FlexIO SPI slave. As a result, the second timer index is ignored. 2.FlexIO SPI slave only support CPOL = 0, which means clock inactive low. 3.For FlexIO SPI master, the input valid time is 1.5 clock cycles, for slave the output valid time is 2.5 clock cycles. So if FlexIO SPI slave communicates with other spi IPs, the maximum baud rate is FlexIO clock frequency divided by 3*2=6. If FlexIO SPI slave communicates with FlexIO SPI master, the maximum baud rate is FlexIO clock frequency divided by (1.5+2.5)*2=8. Example
FLEXIO_SPI_Type spiDev = { .flexioBase = FLEXIO, .SDOPinIndex = 0, .SDIPinIndex = 1, .SCKPinIndex = 2, .CSnPinIndex = 3, .shifterIndex = {0,1}, .timerIndex = {0} }; flexio_spi_slave_config_t config = { .enableSlave = true, .enableInDoze = false, .enableInDebug = true, .enableFastAccess = false, .phase = kFLEXIO_SPI_ClockPhaseFirstEdge, .direction = kFLEXIO_SPI_MsbFirst, .dataMode = kFLEXIO_SPI_8BitMode }; FLEXIO_SPI_SlaveInit(&spiDev, &config);
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
slaveConfig – Pointer to the flexio_spi_slave_config_t structure.
-
void FLEXIO_SPI_SlaveDeinit(FLEXIO_SPI_Type *base)
Gates the FlexIO clock.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type.
-
void FLEXIO_SPI_SlaveGetDefaultConfig(flexio_spi_slave_config_t *slaveConfig)
Gets the default configuration to configure the FlexIO SPI slave. The configuration can be used directly for calling the FLEXIO_SPI_SlaveConfigure(). Example:
flexio_spi_slave_config_t slaveConfig; FLEXIO_SPI_SlaveGetDefaultConfig(&slaveConfig);
- Parameters:
slaveConfig – Pointer to the flexio_spi_slave_config_t structure.
-
uint32_t FLEXIO_SPI_GetStatusFlags(FLEXIO_SPI_Type *base)
Gets FlexIO SPI status flags.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
- Returns:
status flag; Use the status flag to AND the following flag mask and get the status.
kFLEXIO_SPI_TxEmptyFlag
kFLEXIO_SPI_RxEmptyFlag
-
void FLEXIO_SPI_ClearStatusFlags(FLEXIO_SPI_Type *base, uint32_t mask)
Clears FlexIO SPI status flags.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
mask – status flag The parameter can be any combination of the following values:
kFLEXIO_SPI_TxEmptyFlag
kFLEXIO_SPI_RxEmptyFlag
-
void FLEXIO_SPI_EnableInterrupts(FLEXIO_SPI_Type *base, uint32_t mask)
Enables the FlexIO SPI interrupt.
This function enables the FlexIO SPI interrupt.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
mask – interrupt source. The parameter can be any combination of the following values:
kFLEXIO_SPI_RxFullInterruptEnable
kFLEXIO_SPI_TxEmptyInterruptEnable
-
void FLEXIO_SPI_DisableInterrupts(FLEXIO_SPI_Type *base, uint32_t mask)
Disables the FlexIO SPI interrupt.
This function disables the FlexIO SPI interrupt.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
mask – interrupt source The parameter can be any combination of the following values:
kFLEXIO_SPI_RxFullInterruptEnable
kFLEXIO_SPI_TxEmptyInterruptEnable
-
void FLEXIO_SPI_EnableDMA(FLEXIO_SPI_Type *base, uint32_t mask, bool enable)
Enables/disables the FlexIO SPI transmit DMA. This function enables/disables the FlexIO SPI Tx DMA, which means that asserting the kFLEXIO_SPI_TxEmptyFlag does/doesn’t trigger the DMA request.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
mask – SPI DMA source.
enable – True means enable DMA, false means disable DMA.
-
static inline uint32_t FLEXIO_SPI_GetTxDataRegisterAddress(FLEXIO_SPI_Type *base, flexio_spi_shift_direction_t direction)
Gets the FlexIO SPI transmit data register address for MSB first transfer.
This function returns the SPI data register address, which is mainly used by DMA/eDMA.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
direction – Shift direction of MSB first or LSB first.
- Returns:
FlexIO SPI transmit data register address.
-
static inline uint32_t FLEXIO_SPI_GetRxDataRegisterAddress(FLEXIO_SPI_Type *base, flexio_spi_shift_direction_t direction)
Gets the FlexIO SPI receive data register address for the MSB first transfer.
This function returns the SPI data register address, which is mainly used by DMA/eDMA.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
direction – Shift direction of MSB first or LSB first.
- Returns:
FlexIO SPI receive data register address.
-
static inline void FLEXIO_SPI_Enable(FLEXIO_SPI_Type *base, bool enable)
Enables/disables the FlexIO SPI module operation.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type.
enable – True to enable, false does not have any effect.
-
void FLEXIO_SPI_MasterSetBaudRate(FLEXIO_SPI_Type *base, uint32_t baudRate_Bps, uint32_t srcClockHz)
Sets baud rate for the FlexIO SPI transfer, which is only used for the master.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
baudRate_Bps – Baud Rate needed in Hz.
srcClockHz – SPI source clock frequency in Hz.
-
static inline void FLEXIO_SPI_WriteData(FLEXIO_SPI_Type *base, flexio_spi_shift_direction_t direction, uint32_t data)
Writes one byte of data, which is sent using the MSB method.
Note
This is a non-blocking API, which returns directly after the data is put into the data register but the data transfer is not finished on the bus. Ensure that the TxEmptyFlag is asserted before calling this API.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
direction – Shift direction of MSB first or LSB first.
data – 8/16/32 bit data.
-
static inline uint32_t FLEXIO_SPI_ReadData(FLEXIO_SPI_Type *base, flexio_spi_shift_direction_t direction)
Reads 8 bit/16 bit data.
Note
This is a non-blocking API, which returns directly after the data is read from the data register. Ensure that the RxFullFlag is asserted before calling this API.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
direction – Shift direction of MSB first or LSB first.
- Returns:
8 bit/16 bit data received.
-
status_t FLEXIO_SPI_WriteBlocking(FLEXIO_SPI_Type *base, flexio_spi_shift_direction_t direction, const uint8_t *buffer, size_t size)
Sends a buffer of data bytes.
Note
This function blocks using the polling method until all bytes have been sent.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
direction – Shift direction of MSB first or LSB first.
buffer – The data bytes to send.
size – The number of data bytes to send.
- Return values:
kStatus_Success – Successfully create the handle.
kStatus_FLEXIO_SPI_Timeout – The transfer timed out and was aborted.
-
status_t FLEXIO_SPI_ReadBlocking(FLEXIO_SPI_Type *base, flexio_spi_shift_direction_t direction, uint8_t *buffer, size_t size)
Receives a buffer of bytes.
Note
This function blocks using the polling method until all bytes have been received.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
direction – Shift direction of MSB first or LSB first.
buffer – The buffer to store the received bytes.
size – The number of data bytes to be received.
- Return values:
kStatus_Success – Successfully create the handle.
kStatus_FLEXIO_SPI_Timeout – The transfer timed out and was aborted.
-
status_t FLEXIO_SPI_MasterTransferBlocking(FLEXIO_SPI_Type *base, flexio_spi_transfer_t *xfer)
Receives a buffer of bytes.
Note
This function blocks via polling until all bytes have been received.
- Parameters:
base – pointer to FLEXIO_SPI_Type structure
xfer – FlexIO SPI transfer structure, see flexio_spi_transfer_t.
- Return values:
kStatus_Success – Successfully create the handle.
kStatus_FLEXIO_SPI_Timeout – The transfer timed out and was aborted.
-
void FLEXIO_SPI_FlushShifters(FLEXIO_SPI_Type *base)
Flush tx/rx shifters.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
-
status_t FLEXIO_SPI_MasterTransferCreateHandle(FLEXIO_SPI_Type *base, flexio_spi_master_handle_t *handle, flexio_spi_master_transfer_callback_t callback, void *userData)
Initializes the FlexIO SPI Master handle, which is used in transactional functions.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
handle – Pointer to the flexio_spi_master_handle_t structure to store the transfer state.
callback – The callback function.
userData – The parameter of the callback function.
- Return values:
kStatus_Success – Successfully create the handle.
kStatus_OutOfRange – The FlexIO type/handle/ISR table out of range.
-
status_t FLEXIO_SPI_MasterTransferNonBlocking(FLEXIO_SPI_Type *base, flexio_spi_master_handle_t *handle, flexio_spi_transfer_t *xfer)
Master transfer data using IRQ.
This function sends data using IRQ. This is a non-blocking function, which returns right away. When all data is sent out/received, the callback function is called.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
handle – Pointer to the flexio_spi_master_handle_t structure to store the transfer state.
xfer – FlexIO SPI transfer structure. See flexio_spi_transfer_t.
- Return values:
kStatus_Success – Successfully start a transfer.
kStatus_InvalidArgument – Input argument is invalid.
kStatus_FLEXIO_SPI_Busy – SPI is not idle, is running another transfer.
-
void FLEXIO_SPI_MasterTransferAbort(FLEXIO_SPI_Type *base, flexio_spi_master_handle_t *handle)
Aborts the master data transfer, which used IRQ.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
handle – Pointer to the flexio_spi_master_handle_t structure to store the transfer state.
-
status_t FLEXIO_SPI_MasterTransferGetCount(FLEXIO_SPI_Type *base, flexio_spi_master_handle_t *handle, size_t *count)
Gets the data transfer status which used IRQ.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
handle – Pointer to the flexio_spi_master_handle_t structure to store the transfer state.
count – Number of bytes transferred so far by the non-blocking transaction.
- Return values:
kStatus_InvalidArgument – count is Invalid.
kStatus_Success – Successfully return the count.
-
void FLEXIO_SPI_MasterTransferHandleIRQ(void *spiType, void *spiHandle)
FlexIO SPI master IRQ handler function.
- Parameters:
spiType – Pointer to the FLEXIO_SPI_Type structure.
spiHandle – Pointer to the flexio_spi_master_handle_t structure to store the transfer state.
-
status_t FLEXIO_SPI_SlaveTransferCreateHandle(FLEXIO_SPI_Type *base, flexio_spi_slave_handle_t *handle, flexio_spi_slave_transfer_callback_t callback, void *userData)
Initializes the FlexIO SPI Slave handle, which is used in transactional functions.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
handle – Pointer to the flexio_spi_slave_handle_t structure to store the transfer state.
callback – The callback function.
userData – The parameter of the callback function.
- Return values:
kStatus_Success – Successfully create the handle.
kStatus_OutOfRange – The FlexIO type/handle/ISR table out of range.
-
status_t FLEXIO_SPI_SlaveTransferNonBlocking(FLEXIO_SPI_Type *base, flexio_spi_slave_handle_t *handle, flexio_spi_transfer_t *xfer)
Slave transfer data using IRQ.
This function sends data using IRQ. This is a non-blocking function, which returns right away. When all data is sent out/received, the callback function is called.
- Parameters:
handle – Pointer to the flexio_spi_slave_handle_t structure to store the transfer state.
base – Pointer to the FLEXIO_SPI_Type structure.
xfer – FlexIO SPI transfer structure. See flexio_spi_transfer_t.
- Return values:
kStatus_Success – Successfully start a transfer.
kStatus_InvalidArgument – Input argument is invalid.
kStatus_FLEXIO_SPI_Busy – SPI is not idle; it is running another transfer.
-
static inline void FLEXIO_SPI_SlaveTransferAbort(FLEXIO_SPI_Type *base, flexio_spi_slave_handle_t *handle)
Aborts the slave data transfer which used IRQ, share same API with master.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
handle – Pointer to the flexio_spi_slave_handle_t structure to store the transfer state.
-
static inline status_t FLEXIO_SPI_SlaveTransferGetCount(FLEXIO_SPI_Type *base, flexio_spi_slave_handle_t *handle, size_t *count)
Gets the data transfer status which used IRQ, share same API with master.
- Parameters:
base – Pointer to the FLEXIO_SPI_Type structure.
handle – Pointer to the flexio_spi_slave_handle_t structure to store the transfer state.
count – Number of bytes transferred so far by the non-blocking transaction.
- Return values:
kStatus_InvalidArgument – count is Invalid.
kStatus_Success – Successfully return the count.
-
void FLEXIO_SPI_SlaveTransferHandleIRQ(void *spiType, void *spiHandle)
FlexIO SPI slave IRQ handler function.
- Parameters:
spiType – Pointer to the FLEXIO_SPI_Type structure.
spiHandle – Pointer to the flexio_spi_slave_handle_t structure to store the transfer state.
-
FSL_FLEXIO_SPI_DRIVER_VERSION
FlexIO SPI driver version.
Error codes for the FlexIO SPI driver.
Values:
-
enumerator kStatus_FLEXIO_SPI_Busy
FlexIO SPI is busy.
-
enumerator kStatus_FLEXIO_SPI_Idle
SPI is idle
-
enumerator kStatus_FLEXIO_SPI_Error
FlexIO SPI error.
-
enumerator kStatus_FLEXIO_SPI_Timeout
FlexIO SPI timeout polling status flags.
-
enumerator kStatus_FLEXIO_SPI_Busy
-
enum _flexio_spi_clock_phase
FlexIO SPI clock phase configuration.
Values:
-
enumerator kFLEXIO_SPI_ClockPhaseFirstEdge
First edge on SPSCK occurs at the middle of the first cycle of a data transfer.
-
enumerator kFLEXIO_SPI_ClockPhaseSecondEdge
First edge on SPSCK occurs at the start of the first cycle of a data transfer.
-
enumerator kFLEXIO_SPI_ClockPhaseFirstEdge
-
enum _flexio_spi_shift_direction
FlexIO SPI data shifter direction options.
Values:
-
enumerator kFLEXIO_SPI_MsbFirst
Data transfers start with most significant bit.
-
enumerator kFLEXIO_SPI_LsbFirst
Data transfers start with least significant bit.
-
enumerator kFLEXIO_SPI_MsbFirst
-
enum _flexio_spi_data_bitcount_mode
FlexIO SPI data length mode options.
Values:
-
enumerator kFLEXIO_SPI_8BitMode
8-bit data transmission mode.
-
enumerator kFLEXIO_SPI_16BitMode
16-bit data transmission mode.
-
enumerator kFLEXIO_SPI_32BitMode
32-bit data transmission mode.
-
enumerator kFLEXIO_SPI_8BitMode
-
enum _flexio_spi_interrupt_enable
Define FlexIO SPI interrupt mask.
Values:
-
enumerator kFLEXIO_SPI_TxEmptyInterruptEnable
Transmit buffer empty interrupt enable.
-
enumerator kFLEXIO_SPI_RxFullInterruptEnable
Receive buffer full interrupt enable.
-
enumerator kFLEXIO_SPI_TxEmptyInterruptEnable
-
enum _flexio_spi_status_flags
Define FlexIO SPI status mask.
Values:
-
enumerator kFLEXIO_SPI_TxBufferEmptyFlag
Transmit buffer empty flag.
-
enumerator kFLEXIO_SPI_RxBufferFullFlag
Receive buffer full flag.
-
enumerator kFLEXIO_SPI_TxBufferEmptyFlag
-
enum _flexio_spi_dma_enable
Define FlexIO SPI DMA mask.
Values:
-
enumerator kFLEXIO_SPI_TxDmaEnable
Tx DMA request source
-
enumerator kFLEXIO_SPI_RxDmaEnable
Rx DMA request source
-
enumerator kFLEXIO_SPI_DmaAllEnable
All DMA request source
-
enumerator kFLEXIO_SPI_TxDmaEnable
-
enum _flexio_spi_transfer_flags
Define FlexIO SPI transfer flags.
Note
Use kFLEXIO_SPI_csContinuous and one of the other flags to OR together to form the transfer flag.
Values:
-
enumerator kFLEXIO_SPI_8bitMsb
FlexIO SPI 8-bit MSB first
-
enumerator kFLEXIO_SPI_8bitLsb
FlexIO SPI 8-bit LSB first
-
enumerator kFLEXIO_SPI_16bitMsb
FlexIO SPI 16-bit MSB first
-
enumerator kFLEXIO_SPI_16bitLsb
FlexIO SPI 16-bit LSB first
-
enumerator kFLEXIO_SPI_32bitMsb
FlexIO SPI 32-bit MSB first
-
enumerator kFLEXIO_SPI_32bitLsb
FlexIO SPI 32-bit LSB first
-
enumerator kFLEXIO_SPI_csContinuous
Enable the CS signal continuous mode
-
enumerator kFLEXIO_SPI_8bitMsb
-
typedef enum _flexio_spi_clock_phase flexio_spi_clock_phase_t
FlexIO SPI clock phase configuration.
-
typedef enum _flexio_spi_shift_direction flexio_spi_shift_direction_t
FlexIO SPI data shifter direction options.
-
typedef enum _flexio_spi_data_bitcount_mode flexio_spi_data_bitcount_mode_t
FlexIO SPI data length mode options.
-
typedef struct _flexio_spi_type FLEXIO_SPI_Type
Define FlexIO SPI access structure typedef.
-
typedef struct _flexio_spi_master_config flexio_spi_master_config_t
Define FlexIO SPI master configuration structure.
-
typedef struct _flexio_spi_slave_config flexio_spi_slave_config_t
Define FlexIO SPI slave configuration structure.
-
typedef struct _flexio_spi_transfer flexio_spi_transfer_t
Define FlexIO SPI transfer structure.
-
typedef struct _flexio_spi_master_handle flexio_spi_master_handle_t
typedef for flexio_spi_master_handle_t in advance.
-
typedef flexio_spi_master_handle_t flexio_spi_slave_handle_t
Slave handle is the same with master handle.
-
typedef void (*flexio_spi_master_transfer_callback_t)(FLEXIO_SPI_Type *base, flexio_spi_master_handle_t *handle, status_t status, void *userData)
FlexIO SPI master callback for finished transmit.
-
typedef void (*flexio_spi_slave_transfer_callback_t)(FLEXIO_SPI_Type *base, flexio_spi_slave_handle_t *handle, status_t status, void *userData)
FlexIO SPI slave callback for finished transmit.
-
FLEXIO_SPI_DUMMYDATA
FlexIO SPI dummy transfer data, the data is sent while txData is NULL.
-
SPI_RETRY_TIMES
Retry times for waiting flag.
-
FLEXIO_SPI_XFER_DATA_FORMAT(flag)
Get the transfer data format of width and bit order.
-
struct _flexio_spi_type
- #include <fsl_flexio_spi.h>
Define FlexIO SPI access structure typedef.
Public Members
-
FLEXIO_Type *flexioBase
FlexIO base pointer.
-
uint8_t SDOPinIndex
Pin select for data output. To set SDO pin in Hi-Z state, user needs to mux the pin as GPIO input and disable all pull up/down in application.
-
uint8_t SDIPinIndex
Pin select for data input.
-
uint8_t SCKPinIndex
Pin select for clock.
-
uint8_t CSnPinIndex
Pin select for enable.
-
uint8_t shifterIndex[2]
Shifter index used in FlexIO SPI.
-
uint8_t timerIndex[2]
Timer index used in FlexIO SPI.
-
FLEXIO_Type *flexioBase
-
struct _flexio_spi_master_config
- #include <fsl_flexio_spi.h>
Define FlexIO SPI master configuration structure.
Public Members
-
bool enableMaster
Enable/disable FlexIO SPI master after configuration.
-
bool enableInDoze
Enable/disable FlexIO operation in doze mode.
-
bool enableInDebug
Enable/disable FlexIO operation in debug mode.
-
bool enableFastAccess
Enable/disable fast access to FlexIO registers, fast access requires the FlexIO clock to be at least twice the frequency of the bus clock.
-
uint32_t baudRate_Bps
Baud rate in Bps.
-
flexio_spi_clock_phase_t phase
Clock phase.
-
flexio_spi_data_bitcount_mode_t dataMode
8bit or 16bit mode.
-
bool enableMaster
-
struct _flexio_spi_slave_config
- #include <fsl_flexio_spi.h>
Define FlexIO SPI slave configuration structure.
Public Members
-
bool enableSlave
Enable/disable FlexIO SPI slave after configuration.
-
bool enableInDoze
Enable/disable FlexIO operation in doze mode.
-
bool enableInDebug
Enable/disable FlexIO operation in debug mode.
-
bool enableFastAccess
Enable/disable fast access to FlexIO registers, fast access requires the FlexIO clock to be at least twice the frequency of the bus clock.
-
flexio_spi_clock_phase_t phase
Clock phase.
-
flexio_spi_data_bitcount_mode_t dataMode
8bit or 16bit mode.
-
bool enableSlave
-
struct _flexio_spi_transfer
- #include <fsl_flexio_spi.h>
Define FlexIO SPI transfer structure.
Public Members
-
const uint8_t *txData
Send buffer.
-
uint8_t *rxData
Receive buffer.
-
size_t dataSize
Transfer bytes.
-
uint8_t flags
FlexIO SPI control flag, MSB first or LSB first.
-
const uint8_t *txData
-
struct _flexio_spi_master_handle
- #include <fsl_flexio_spi.h>
Define FlexIO SPI handle structure.
Public Members
-
const uint8_t *txData
Transfer buffer.
-
uint8_t *rxData
Receive buffer.
-
size_t transferSize
Total bytes to be transferred.
-
volatile size_t txRemainingBytes
Send data remaining in bytes.
-
volatile size_t rxRemainingBytes
Receive data remaining in bytes.
-
volatile uint32_t state
FlexIO SPI internal state.
-
uint8_t bytePerFrame
SPI mode, 2bytes or 1byte in a frame
-
flexio_spi_shift_direction_t direction
Shift direction.
-
flexio_spi_master_transfer_callback_t callback
FlexIO SPI callback.
-
void *userData
Callback parameter.
-
const uint8_t *txData
FlexIO UART Driver
-
status_t FLEXIO_UART_Init(FLEXIO_UART_Type *base, const flexio_uart_config_t *userConfig, uint32_t srcClock_Hz)
Ungates the FlexIO clock, resets the FlexIO module, configures FlexIO UART hardware, and configures the FlexIO UART with FlexIO UART configuration. The configuration structure can be filled by the user or be set with default values by FLEXIO_UART_GetDefaultConfig().
Example
FLEXIO_UART_Type base = { .flexioBase = FLEXIO, .TxPinIndex = 0, .RxPinIndex = 1, .shifterIndex = {0,1}, .timerIndex = {0,1} }; flexio_uart_config_t config = { .enableInDoze = false, .enableInDebug = true, .enableFastAccess = false, .baudRate_Bps = 115200U, .bitCountPerChar = 8 }; FLEXIO_UART_Init(base, &config, srcClock_Hz);
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
userConfig – Pointer to the flexio_uart_config_t structure.
srcClock_Hz – FlexIO source clock in Hz.
- Return values:
kStatus_Success – Configuration success.
kStatus_FLEXIO_UART_BaudrateNotSupport – Baudrate is not supported for current clock source frequency.
-
void FLEXIO_UART_Deinit(FLEXIO_UART_Type *base)
Resets the FlexIO UART shifter and timer config.
Note
After calling this API, call the FLEXO_UART_Init to use the FlexIO UART module.
- Parameters:
base – Pointer to FLEXIO_UART_Type structure
-
void FLEXIO_UART_GetDefaultConfig(flexio_uart_config_t *userConfig)
Gets the default configuration to configure the FlexIO UART. The configuration can be used directly for calling the FLEXIO_UART_Init(). Example:
flexio_uart_config_t config; FLEXIO_UART_GetDefaultConfig(&userConfig);
- Parameters:
userConfig – Pointer to the flexio_uart_config_t structure.
-
uint32_t FLEXIO_UART_GetStatusFlags(FLEXIO_UART_Type *base)
Gets the FlexIO UART status flags.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
- Returns:
FlexIO UART status flags.
-
void FLEXIO_UART_ClearStatusFlags(FLEXIO_UART_Type *base, uint32_t mask)
Gets the FlexIO UART status flags.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
mask – Status flag. The parameter can be any combination of the following values:
kFLEXIO_UART_TxDataRegEmptyFlag
kFLEXIO_UART_RxEmptyFlag
kFLEXIO_UART_RxOverRunFlag
-
void FLEXIO_UART_EnableInterrupts(FLEXIO_UART_Type *base, uint32_t mask)
Enables the FlexIO UART interrupt.
This function enables the FlexIO UART interrupt.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
mask – Interrupt source.
-
void FLEXIO_UART_DisableInterrupts(FLEXIO_UART_Type *base, uint32_t mask)
Disables the FlexIO UART interrupt.
This function disables the FlexIO UART interrupt.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
mask – Interrupt source.
-
static inline uint32_t FLEXIO_UART_GetTxDataRegisterAddress(FLEXIO_UART_Type *base)
Gets the FlexIO UARt transmit data register address.
This function returns the UART data register address, which is mainly used by DMA/eDMA.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
- Returns:
FlexIO UART transmit data register address.
-
static inline uint32_t FLEXIO_UART_GetRxDataRegisterAddress(FLEXIO_UART_Type *base)
Gets the FlexIO UART receive data register address.
This function returns the UART data register address, which is mainly used by DMA/eDMA.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
- Returns:
FlexIO UART receive data register address.
-
static inline void FLEXIO_UART_EnableTxDMA(FLEXIO_UART_Type *base, bool enable)
Enables/disables the FlexIO UART transmit DMA. This function enables/disables the FlexIO UART Tx DMA, which means asserting the kFLEXIO_UART_TxDataRegEmptyFlag does/doesn’t trigger the DMA request.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
enable – True to enable, false to disable.
-
static inline void FLEXIO_UART_EnableRxDMA(FLEXIO_UART_Type *base, bool enable)
Enables/disables the FlexIO UART receive DMA. This function enables/disables the FlexIO UART Rx DMA, which means asserting kFLEXIO_UART_RxDataRegFullFlag does/doesn’t trigger the DMA request.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
enable – True to enable, false to disable.
-
static inline void FLEXIO_UART_Enable(FLEXIO_UART_Type *base, bool enable)
Enables/disables the FlexIO UART module operation.
- Parameters:
base – Pointer to the FLEXIO_UART_Type.
enable – True to enable, false does not have any effect.
-
static inline void FLEXIO_UART_WriteByte(FLEXIO_UART_Type *base, const uint8_t *buffer)
Writes one byte of data.
Note
This is a non-blocking API, which returns directly after the data is put into the data register. Ensure that the TxEmptyFlag is asserted before calling this API.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
buffer – The data bytes to send.
-
static inline void FLEXIO_UART_ReadByte(FLEXIO_UART_Type *base, uint8_t *buffer)
Reads one byte of data.
Note
This is a non-blocking API, which returns directly after the data is read from the data register. Ensure that the RxFullFlag is asserted before calling this API.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
buffer – The buffer to store the received bytes.
-
status_t FLEXIO_UART_WriteBlocking(FLEXIO_UART_Type *base, const uint8_t *txData, size_t txSize)
Sends a buffer of data bytes.
Note
This function blocks using the polling method until all bytes have been sent.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
txData – The data bytes to send.
txSize – The number of data bytes to send.
- Return values:
kStatus_FLEXIO_UART_Timeout – Transmission timed out and was aborted.
kStatus_Success – Successfully wrote all data.
-
status_t FLEXIO_UART_ReadBlocking(FLEXIO_UART_Type *base, uint8_t *rxData, size_t rxSize)
Receives a buffer of bytes.
Note
This function blocks using the polling method until all bytes have been received.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
rxData – The buffer to store the received bytes.
rxSize – The number of data bytes to be received.
- Return values:
kStatus_FLEXIO_UART_Timeout – Transmission timed out and was aborted.
kStatus_Success – Successfully received all data.
-
status_t FLEXIO_UART_TransferCreateHandle(FLEXIO_UART_Type *base, flexio_uart_handle_t *handle, flexio_uart_transfer_callback_t callback, void *userData)
Initializes the UART handle.
This function initializes the FlexIO UART handle, which can be used for other FlexIO UART transactional APIs. Call this API once to get the initialized handle.
The UART driver supports the “background” receiving, which means that users can set up a RX ring buffer optionally. Data received is stored into the ring buffer even when the user doesn’t call the FLEXIO_UART_TransferReceiveNonBlocking() API. If there is already data received in the ring buffer, users can get the received data from the ring buffer directly. The ring buffer is disabled if passing NULL as
ringBuffer
.- Parameters:
base – to FLEXIO_UART_Type structure.
handle – Pointer to the flexio_uart_handle_t structure to store the transfer state.
callback – The callback function.
userData – The parameter of the callback function.
- Return values:
kStatus_Success – Successfully create the handle.
kStatus_OutOfRange – The FlexIO type/handle/ISR table out of range.
-
void FLEXIO_UART_TransferStartRingBuffer(FLEXIO_UART_Type *base, flexio_uart_handle_t *handle, uint8_t *ringBuffer, size_t ringBufferSize)
Sets up the RX ring buffer.
This function sets up the RX ring buffer to a specific UART handle.
When the RX ring buffer is used, data received is stored into the ring buffer even when the user doesn’t call the UART_ReceiveNonBlocking() API. If there is already data received in the ring buffer, users can get the received data from the ring buffer directly.
Note
When using the RX ring buffer, one byte is reserved for internal use. In other words, if
ringBufferSize
is 32, only 31 bytes are used for saving data.- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
handle – Pointer to the flexio_uart_handle_t structure to store the transfer state.
ringBuffer – Start address of ring buffer for background receiving. Pass NULL to disable the ring buffer.
ringBufferSize – Size of the ring buffer.
-
void FLEXIO_UART_TransferStopRingBuffer(FLEXIO_UART_Type *base, flexio_uart_handle_t *handle)
Aborts the background transfer and uninstalls the ring buffer.
This function aborts the background transfer and uninstalls the ring buffer.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
handle – Pointer to the flexio_uart_handle_t structure to store the transfer state.
-
status_t FLEXIO_UART_TransferSendNonBlocking(FLEXIO_UART_Type *base, flexio_uart_handle_t *handle, flexio_uart_transfer_t *xfer)
Transmits a buffer of data using the interrupt method.
This function sends data using an interrupt method. This is a non-blocking function, which returns directly without waiting for all data to be written to the TX register. When all data is written to the TX register in ISR, the FlexIO UART driver calls the callback function and passes the kStatus_FLEXIO_UART_TxIdle as status parameter.
Note
The kStatus_FLEXIO_UART_TxIdle is passed to the upper layer when all data is written to the TX register. However, it does not ensure that all data is sent out.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
handle – Pointer to the flexio_uart_handle_t structure to store the transfer state.
xfer – FlexIO UART transfer structure. See flexio_uart_transfer_t.
- Return values:
kStatus_Success – Successfully starts the data transmission.
kStatus_UART_TxBusy – Previous transmission still not finished, data not written to the TX register.
-
void FLEXIO_UART_TransferAbortSend(FLEXIO_UART_Type *base, flexio_uart_handle_t *handle)
Aborts the interrupt-driven data transmit.
This function aborts the interrupt-driven data sending. Get the remainBytes to find out how many bytes are still not sent out.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
handle – Pointer to the flexio_uart_handle_t structure to store the transfer state.
-
status_t FLEXIO_UART_TransferGetSendCount(FLEXIO_UART_Type *base, flexio_uart_handle_t *handle, size_t *count)
Gets the number of bytes sent.
This function gets the number of bytes sent driven by interrupt.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
handle – Pointer to the flexio_uart_handle_t structure to store the transfer state.
count – Number of bytes sent so far by the non-blocking transaction.
- Return values:
kStatus_NoTransferInProgress – transfer has finished or no transfer in progress.
kStatus_Success – Successfully return the count.
-
status_t FLEXIO_UART_TransferReceiveNonBlocking(FLEXIO_UART_Type *base, flexio_uart_handle_t *handle, flexio_uart_transfer_t *xfer, size_t *receivedBytes)
Receives a buffer of data using the interrupt method.
This function receives data using the interrupt method. This is a non-blocking function, which returns without waiting for all data to be received. If the RX ring buffer is used and not empty, the data in ring buffer is copied and the parameter
receivedBytes
shows how many bytes are copied from the ring buffer. After copying, if the data in ring buffer is not enough to read, the receive request is saved by the UART driver. When new data arrives, the receive request is serviced first. When all data is received, the UART driver notifies the upper layer through a callback function and passes the status parameter kStatus_UART_RxIdle. For example, if the upper layer needs 10 bytes but there are only 5 bytes in the ring buffer, the 5 bytes are copied to xfer->data. This function returns with the parameterreceivedBytes
set to 5. For the last 5 bytes, newly arrived data is saved from the xfer->data[5]. When 5 bytes are received, the UART driver notifies upper layer. If the RX ring buffer is not enabled, this function enables the RX and RX interrupt to receive data to xfer->data. When all data is received, the upper layer is notified.- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
handle – Pointer to the flexio_uart_handle_t structure to store the transfer state.
xfer – UART transfer structure. See flexio_uart_transfer_t.
receivedBytes – Bytes received from the ring buffer directly.
- Return values:
kStatus_Success – Successfully queue the transfer into the transmit queue.
kStatus_FLEXIO_UART_RxBusy – Previous receive request is not finished.
-
void FLEXIO_UART_TransferAbortReceive(FLEXIO_UART_Type *base, flexio_uart_handle_t *handle)
Aborts the receive data which was using IRQ.
This function aborts the receive data which was using IRQ.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
handle – Pointer to the flexio_uart_handle_t structure to store the transfer state.
-
status_t FLEXIO_UART_TransferGetReceiveCount(FLEXIO_UART_Type *base, flexio_uart_handle_t *handle, size_t *count)
Gets the number of bytes received.
This function gets the number of bytes received driven by interrupt.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
handle – Pointer to the flexio_uart_handle_t structure to store the transfer state.
count – Number of bytes received so far by the non-blocking transaction.
- Return values:
kStatus_NoTransferInProgress – transfer has finished or no transfer in progress.
kStatus_Success – Successfully return the count.
-
void FLEXIO_UART_TransferHandleIRQ(void *uartType, void *uartHandle)
FlexIO UART IRQ handler function.
This function processes the FlexIO UART transmit and receives the IRQ request.
- Parameters:
uartType – Pointer to the FLEXIO_UART_Type structure.
uartHandle – Pointer to the flexio_uart_handle_t structure to store the transfer state.
-
void FLEXIO_UART_FlushShifters(FLEXIO_UART_Type *base)
Flush tx/rx shifters.
- Parameters:
base – Pointer to the FLEXIO_UART_Type structure.
-
FSL_FLEXIO_UART_DRIVER_VERSION
FlexIO UART driver version.
Error codes for the UART driver.
Values:
-
enumerator kStatus_FLEXIO_UART_TxBusy
Transmitter is busy.
-
enumerator kStatus_FLEXIO_UART_RxBusy
Receiver is busy.
-
enumerator kStatus_FLEXIO_UART_TxIdle
UART transmitter is idle.
-
enumerator kStatus_FLEXIO_UART_RxIdle
UART receiver is idle.
-
enumerator kStatus_FLEXIO_UART_ERROR
ERROR happens on UART.
-
enumerator kStatus_FLEXIO_UART_RxRingBufferOverrun
UART RX software ring buffer overrun.
-
enumerator kStatus_FLEXIO_UART_RxHardwareOverrun
UART RX receiver overrun.
-
enumerator kStatus_FLEXIO_UART_Timeout
UART times out.
-
enumerator kStatus_FLEXIO_UART_BaudrateNotSupport
Baudrate is not supported in current clock source
-
enumerator kStatus_FLEXIO_UART_TxBusy
-
enum _flexio_uart_bit_count_per_char
FlexIO UART bit count per char.
Values:
-
enumerator kFLEXIO_UART_7BitsPerChar
7-bit data characters
-
enumerator kFLEXIO_UART_8BitsPerChar
8-bit data characters
-
enumerator kFLEXIO_UART_9BitsPerChar
9-bit data characters
-
enumerator kFLEXIO_UART_7BitsPerChar
-
enum _flexio_uart_interrupt_enable
Define FlexIO UART interrupt mask.
Values:
-
enumerator kFLEXIO_UART_TxDataRegEmptyInterruptEnable
Transmit buffer empty interrupt enable.
-
enumerator kFLEXIO_UART_RxDataRegFullInterruptEnable
Receive buffer full interrupt enable.
-
enumerator kFLEXIO_UART_TxDataRegEmptyInterruptEnable
-
enum _flexio_uart_status_flags
Define FlexIO UART status mask.
Values:
-
enumerator kFLEXIO_UART_TxDataRegEmptyFlag
Transmit buffer empty flag.
-
enumerator kFLEXIO_UART_RxDataRegFullFlag
Receive buffer full flag.
-
enumerator kFLEXIO_UART_RxOverRunFlag
Receive buffer over run flag.
-
enumerator kFLEXIO_UART_TxDataRegEmptyFlag
-
typedef enum _flexio_uart_bit_count_per_char flexio_uart_bit_count_per_char_t
FlexIO UART bit count per char.
-
typedef struct _flexio_uart_type FLEXIO_UART_Type
Define FlexIO UART access structure typedef.
-
typedef struct _flexio_uart_config flexio_uart_config_t
Define FlexIO UART user configuration structure.
-
typedef struct _flexio_uart_transfer flexio_uart_transfer_t
Define FlexIO UART transfer structure.
-
typedef struct _flexio_uart_handle flexio_uart_handle_t
-
typedef void (*flexio_uart_transfer_callback_t)(FLEXIO_UART_Type *base, flexio_uart_handle_t *handle, status_t status, void *userData)
FlexIO UART transfer callback function.
-
UART_RETRY_TIMES
Retry times for waiting flag.
-
struct _flexio_uart_type
- #include <fsl_flexio_uart.h>
Define FlexIO UART access structure typedef.
Public Members
-
FLEXIO_Type *flexioBase
FlexIO base pointer.
-
uint8_t TxPinIndex
Pin select for UART_Tx.
-
uint8_t RxPinIndex
Pin select for UART_Rx.
-
uint8_t shifterIndex[2]
Shifter index used in FlexIO UART.
-
uint8_t timerIndex[2]
Timer index used in FlexIO UART.
-
FLEXIO_Type *flexioBase
-
struct _flexio_uart_config
- #include <fsl_flexio_uart.h>
Define FlexIO UART user configuration structure.
Public Members
-
bool enableUart
Enable/disable FlexIO UART TX & RX.
-
bool enableInDoze
Enable/disable FlexIO operation in doze mode
-
bool enableInDebug
Enable/disable FlexIO operation in debug mode
-
bool enableFastAccess
Enable/disable fast access to FlexIO registers, fast access requires the FlexIO clock to be at least twice the frequency of the bus clock.
-
uint32_t baudRate_Bps
Baud rate in Bps.
-
flexio_uart_bit_count_per_char_t bitCountPerChar
number of bits, 7/8/9 -bit
-
bool enableUart
-
struct _flexio_uart_transfer
- #include <fsl_flexio_uart.h>
Define FlexIO UART transfer structure.
Public Members
-
size_t dataSize
Transfer size
-
size_t dataSize
-
struct _flexio_uart_handle
- #include <fsl_flexio_uart.h>
Define FLEXIO UART handle structure.
Public Members
-
const uint8_t *volatile txData
Address of remaining data to send.
-
volatile size_t txDataSize
Size of the remaining data to send.
-
uint8_t *volatile rxData
Address of remaining data to receive.
-
volatile size_t rxDataSize
Size of the remaining data to receive.
-
size_t txDataSizeAll
Total bytes to be sent.
-
size_t rxDataSizeAll
Total bytes to be received.
-
uint8_t *rxRingBuffer
Start address of the receiver ring buffer.
-
size_t rxRingBufferSize
Size of the ring buffer.
-
volatile uint16_t rxRingBufferHead
Index for the driver to store received data into ring buffer.
-
volatile uint16_t rxRingBufferTail
Index for the user to get data from the ring buffer.
-
flexio_uart_transfer_callback_t callback
Callback function.
-
void *userData
UART callback function parameter.
-
volatile uint8_t txState
TX transfer state.
-
volatile uint8_t rxState
RX transfer state
-
const uint8_t *volatile txData
-
union __unnamed113__
Public Members
-
uint8_t *data
The buffer of data to be transfer.
-
uint8_t *rxData
The buffer to receive data.
-
const uint8_t *txData
The buffer of data to be sent.
-
uint8_t *data
FLEXRAM: on-chip RAM manager
FLEXRAM bank type.
Values:
-
enumerator kFLEXRAM_BankNotUsed
bank is not used
-
enumerator kFLEXRAM_BankOCRAM
bank is OCRAM
-
enumerator kFLEXRAM_BankDTCM
bank is DTCM
-
enumerator kFLEXRAM_BankITCM
bank is ITCM
-
enumerator kFLEXRAM_BankNotUsed
-
enum _flexram_bank_allocate_src
FLEXRAM bank allocate source.
Values:
-
enumerator kFLEXRAM_BankAllocateThroughHardwareFuse
allocate ram through hardware fuse value
-
enumerator kFLEXRAM_BankAllocateThroughBankCfg
allocate ram through FLEXRAM_BANK_CFG
-
enumerator kFLEXRAM_BankAllocateThroughHardwareFuse
-
typedef enum _flexram_bank_allocate_src flexram_bank_allocate_src_t
FLEXRAM bank allocate source.
-
typedef struct _flexram_allocate_ram flexram_allocate_ram_t
FLEXRAM allocate ocram, itcm, dtcm size.
-
status_t FLEXRAM_AllocateRam(flexram_allocate_ram_t *config)
FLEXRAM allocate on-chip ram for OCRAM,ITCM,DTCM This function is independent of FLEXRAM_Init, it can be called directly if ram re-allocate is needed.
- Parameters:
config – allocate configuration.
- Return values:
kStatus_InvalidArgument – the argument is invalid kStatus_Success allocate success
-
static inline void FLEXRAM_SetAllocateRamSrc(flexram_bank_allocate_src_t src)
FLEXRAM set allocate on-chip ram source.
- Parameters:
src – bank config source select value.
-
FSL_SOC_FLEXRAM_ALLOCATE_DRIVER_VERSION
SOC_FLEXRAM_ALLOCATE driver version 2.0.2.
-
void FLEXRAM_Init(FLEXRAM_Type *base)
FLEXRAM module initialization function.
- Parameters:
base – FLEXRAM base address.
-
void FLEXRAM_Deinit(FLEXRAM_Type *base)
De-initializes the FLEXRAM.
-
static inline uint32_t FLEXRAM_GetInterruptStatus(FLEXRAM_Type *base)
FLEXRAM module gets interrupt status.
- Parameters:
base – FLEXRAM base address.
-
static inline void FLEXRAM_ClearInterruptStatus(FLEXRAM_Type *base, uint32_t status)
FLEXRAM module clears interrupt status.
- Parameters:
base – FLEXRAM base address.
status – Status to be cleared.
-
static inline void FLEXRAM_EnableInterruptStatus(FLEXRAM_Type *base, uint32_t status)
FLEXRAM module enables interrupt status.
- Parameters:
base – FLEXRAM base address.
status – Status to be enabled.
-
static inline void FLEXRAM_DisableInterruptStatus(FLEXRAM_Type *base, uint32_t status)
FLEXRAM module disable interrupt status.
- Parameters:
base – FLEXRAM base address.
status – Status to be disabled.
-
static inline void FLEXRAM_EnableInterruptSignal(FLEXRAM_Type *base, uint32_t status)
FLEXRAM module enables interrupt.
- Parameters:
base – FLEXRAM base address.
status – Status interrupt to be enabled.
-
static inline void FLEXRAM_DisableInterruptSignal(FLEXRAM_Type *base, uint32_t status)
FLEXRAM module disables interrupt.
- Parameters:
base – FLEXRAM base address.
status – Status interrupt to be disabled.
-
FSL_FLEXRAM_DRIVER_VERSION
Driver version.
Flexram write/read selection.
Values:
-
enumerator kFLEXRAM_Read
read
-
enumerator kFLEXRAM_Write
write
-
enumerator kFLEXRAM_Read
Interrupt status flag mask.
Values:
-
enumerator kFLEXRAM_OCRAMAccessError
OCRAM accesses unallocated address
-
enumerator kFLEXRAM_DTCMAccessError
DTCM accesses unallocated address
-
enumerator kFLEXRAM_ITCMAccessError
ITCM accesses unallocated address
-
enumerator kFLEXRAM_OCRAMMagicAddrMatch
OCRAM magic address match
-
enumerator kFLEXRAM_DTCMMagicAddrMatch
DTCM magic address match
-
enumerator kFLEXRAM_ITCMMagicAddrMatch
ITCM magic address match
-
enumerator kFLEXRAM_OCRAMECCMultiError
-
enumerator kFLEXRAM_OCRAMECCSingleError
-
enumerator kFLEXRAM_ITCMECCMultiError
-
enumerator kFLEXRAM_ITCMECCSingleError
-
enumerator kFLEXRAM_D0TCMECCMultiError
-
enumerator kFLEXRAM_D0TCMECCSingleError
-
enumerator kFLEXRAM_D1TCMECCMultiError
-
enumerator kFLEXRAM_D1TCMECCSingleError
-
enumerator kFLEXRAM_InterruptStatusAll
-
enumerator kFLEXRAM_OCRAMAccessError
-
enum _flexram_tcm_access_mode
FLEXRAM TCM access mode. Fast access mode expected to be finished in 1-cycle; Wait access mode expected to be finished in 2-cycle. Wait access mode is a feature of the flexram and it should be used when the CPU clock is too fast to finish TCM access in 1-cycle. Normally, fast mode is the default mode, the efficiency of the TCM access will better.
Values:
-
enumerator kFLEXRAM_TCMAccessFastMode
fast access mode
-
enumerator kFLEXRAM_TCMAccessWaitMode
wait access mode
-
enumerator kFLEXRAM_TCMAccessFastMode
FLEXRAM TCM support size.
Values:
-
enumerator kFLEXRAM_TCMSize32KB
TCM total size be 32KB
-
enumerator kFLEXRAM_TCMSize64KB
TCM total size be 64KB
-
enumerator kFLEXRAM_TCMSize128KB
TCM total size be 128KB
-
enumerator kFLEXRAM_TCMSize256KB
TCM total size be 256KB
-
enumerator kFLEXRAM_TCMSize512KB
TCM total size be 512KB
-
enumerator kFLEXRAM_TCMSize32KB
-
enum _flexram_memory_type
FLEXRAM memory type, such as OCRAM/ITCM/D0TCM/D1TCM.
Values:
-
enumerator kFLEXRAM_OCRAM
Memory type OCRAM
-
enumerator kFLEXRAM_ITCM
Memory type ITCM
-
enumerator kFLEXRAM_D0TCM
Memory type D0TCM
-
enumerator kFLEXRAM_D1TCM
Memory type D1TCM
-
enumerator kFLEXRAM_OCRAM
-
typedef enum _flexram_tcm_access_mode flexram_tcm_access_mode_t
FLEXRAM TCM access mode. Fast access mode expected to be finished in 1-cycle; Wait access mode expected to be finished in 2-cycle. Wait access mode is a feature of the flexram and it should be used when the CPU clock is too fast to finish TCM access in 1-cycle. Normally, fast mode is the default mode, the efficiency of the TCM access will better.
-
typedef enum _flexram_memory_type flexram_memory_type_t
FLEXRAM memory type, such as OCRAM/ITCM/D0TCM/D1TCM.
-
typedef struct _flexram_ecc_error_type flexram_ecc_error_type_t
FLEXRAM error type, such as single bit error position, multi-bit error position.
-
typedef struct _flexram_ocram_ecc_single_error_info flexram_ocram_ecc_single_error_info_t
FLEXRAM ocram ecc single error information, including single error information, error address, error data.
-
typedef struct _flexram_ocram_ecc_multi_error_info flexram_ocram_ecc_multi_error_info_t
FLEXRAM ocram ecc multiple error information, including multiple error information, error address, error data.
-
typedef struct _flexram_itcm_ecc_single_error_info flexram_itcm_ecc_single_error_info_t
FLEXRAM itcm ecc single error information, including single error information, error address, error data.
-
typedef struct _flexram_itcm_ecc_multi_error_info flexram_itcm_ecc_multi_error_info_t
FLEXRAM itcm ecc multiple error information, including multiple error information, error address, error data.
-
typedef struct _flexram_dtcm_ecc_single_error_info flexram_dtcm_ecc_single_error_info_t
FLEXRAM dtcm ecc single error information, including single error information, error address, error data.
-
typedef struct _flexram_dtcm_ecc_multi_error_info flexram_dtcm_ecc_multi_error_info_t
FLEXRAM dtcm ecc multiple error information, including multiple error information, error address, error data.
-
const uint8_t ocramBankNum
ocram banknumber which the SOC support
-
const uint8_t dtcmBankNum
dtcm bank number to allocate, the number should be power of 2
-
const uint8_t itcmBankNum
itcm bank number to allocate, the number should be power of 2
-
static inline void FLEXRAM_SetTCMReadAccessMode(FLEXRAM_Type *base, flexram_tcm_access_mode_t mode)
FLEXRAM module sets TCM read access mode.
- Parameters:
base – FLEXRAM base address.
mode – Access mode.
-
static inline void FLEXRAM_SetTCMWriteAccessMode(FLEXRAM_Type *base, flexram_tcm_access_mode_t mode)
FLEXRAM module set TCM write access mode.
- Parameters:
base – FLEXRAM base address.
mode – Access mode.
-
static inline void FLEXRAM_EnableForceRamClockOn(FLEXRAM_Type *base, bool enable)
FLEXRAM module force ram clock on.
- Parameters:
base – FLEXRAM base address.
enable – Enable or disable clock force on.
-
static inline void FLEXRAM_SetOCRAMMagicAddr(FLEXRAM_Type *base, uint16_t magicAddr, uint32_t rwSel)
FLEXRAM OCRAM magic addr configuration. When read/write access hit magic address, it will generate interrupt.
- Parameters:
base – FLEXRAM base address.
magicAddr – Magic address, the actual address bits [18:3] is corresponding to the register field [16:1].
rwSel – Read/write selection. 0 for read access while 1 for write access.
-
static inline void FLEXRAM_SetDTCMMagicAddr(FLEXRAM_Type *base, uint16_t magicAddr, uint32_t rwSel)
FLEXRAM DTCM magic addr configuration. When read/write access hits magic address, it will generate interrupt.
- Parameters:
base – FLEXRAM base address.
magicAddr – Magic address, the actual address bits [18:3] is corresponding to the register field [16:1].
rwSel – Read/write selection. 0 for read access while 1 write access.
-
static inline void FLEXRAM_SetITCMMagicAddr(FLEXRAM_Type *base, uint16_t magicAddr, uint32_t rwSel)
FLEXRAM ITCM magic addr configuration. When read/write access hits magic address, it will generate interrupt.
- Parameters:
base – FLEXRAM base address.
magicAddr – Magic address, the actual address bits [18:3] is corresponding to the register field [16:1].
rwSel – Read/write selection. 0 for read access while 1 for write access.
-
void FLEXRAM_EnableECC(FLEXRAM_Type *base, bool OcramECCEnable, bool TcmECCEnable)
FLEXRAM get ocram ecc single error information.
- Parameters:
base – FLEXRAM base address.
OcramECCEnable – ocram ecc enablement.
TcmECCEnable – tcm(itcm/d0tcm/d1tcm) ecc enablement.
-
void FLEXRAM_ErrorInjection(FLEXRAM_Type *base, flexram_memory_type_t memory, flexram_ecc_error_type_t *error)
FLEXRAM ECC error injection.
- Parameters:
base – FLEXRAM base address.
memory – memory type, such as OCRAM/ITCM/DTCM.
error – ECC error type.
-
void FLEXRAM_GetOcramSingleErroInfo(FLEXRAM_Type *base, flexram_ocram_ecc_single_error_info_t *info)
FLEXRAM get ocram ecc single error information.
- Parameters:
base – FLEXRAM base address.
info – ecc error information.
-
void FLEXRAM_GetOcramMultiErroInfo(FLEXRAM_Type *base, flexram_ocram_ecc_multi_error_info_t *info)
FLEXRAM get ocram ecc multiple error information.
- Parameters:
base – FLEXRAM base address.
info – ecc error information.
-
void FLEXRAM_GetItcmSingleErroInfo(FLEXRAM_Type *base, flexram_itcm_ecc_single_error_info_t *info)
FLEXRAM get itcm ecc single error information.
- Parameters:
base – FLEXRAM base address.
info – ecc error information.
-
void FLEXRAM_GetItcmMultiErroInfo(FLEXRAM_Type *base, flexram_itcm_ecc_multi_error_info_t *info)
FLEXRAM get itcm ecc multiple error information.
- Parameters:
base – FLEXRAM base address.
info – ecc error information.
-
void FLEXRAM_GetDtcmSingleErroInfo(FLEXRAM_Type *base, flexram_dtcm_ecc_single_error_info_t *info, uint8_t bank)
FLEXRAM get d0tcm ecc single error information.
- Parameters:
base – FLEXRAM base address.
info – ecc error information.
bank – DTCM bank, 0 is D0TCM, 1 is D1TCM.
-
void FLEXRAM_GetDtcmMultiErroInfo(FLEXRAM_Type *base, flexram_dtcm_ecc_multi_error_info_t *info, uint8_t bank)
FLEXRAM get d0tcm ecc multiple error information.
- Parameters:
base – FLEXRAM base address.
info – ecc error information.
bank – DTCM bank, 0 is D0TCM, 1 is D1TCM.
-
FLEXRAM_ECC_ERROR_DETAILED_INFO
Get ECC error detailed information.
-
struct _flexram_allocate_ram
- #include <fsl_flexram_allocate.h>
FLEXRAM allocate ocram, itcm, dtcm size.
-
struct _flexram_ecc_error_type
- #include <fsl_flexram.h>
FLEXRAM error type, such as single bit error position, multi-bit error position.
Public Members
-
uint8_t SingleBitPos
Bit position of the bit to inject ECC Error.
-
uint8_t SecondBitPos
Bit position of the second bit to inject multi-bit ECC Error
-
bool Fource1BitDataInversion
Force One 1-Bit Data Inversion (single-bit ECC error) on memory write access
-
bool FourceOneNCDataInversion
Force One Non-correctable Data Inversion(multi-bit ECC error) on memory write access
-
bool FourceConti1BitDataInversion
Force Continuous 1-Bit Data Inversions (single-bit ECC error) on memory write access
-
bool FourceContiNCDataInversion
Force Continuous Non-correctable Data Inversions (multi-bit ECC error) on memory write access
-
uint8_t SingleBitPos
-
struct _flexram_ocram_ecc_single_error_info
- #include <fsl_flexram.h>
FLEXRAM ocram ecc single error information, including single error information, error address, error data.
Public Members
-
uint32_t OcramSingleErrorInfo
Ocram single error information, user should parse it by themself.
-
uint32_t OcramSingleErrorAddr
Ocram single error address
-
uint32_t OcramSingleErrorDataLSB
Ocram single error data LSB
-
uint32_t OcramSingleErrorDataMSB
Ocram single error data MSB
-
uint32_t OcramSingleErrorInfo
-
struct _flexram_ocram_ecc_multi_error_info
- #include <fsl_flexram.h>
FLEXRAM ocram ecc multiple error information, including multiple error information, error address, error data.
Public Members
-
uint32_t OcramMultiErrorInfo
Ocram single error information, user should parse it by themself.
-
uint32_t OcramMultiErrorAddr
Ocram multiple error address
-
uint32_t OcramMultiErrorDataLSB
Ocram multiple error data LSB
-
uint32_t OcramMultiErrorDataMSB
Ocram multiple error data MSB
-
uint32_t OcramMultiErrorInfo
-
struct _flexram_itcm_ecc_single_error_info
- #include <fsl_flexram.h>
FLEXRAM itcm ecc single error information, including single error information, error address, error data.
Public Members
-
uint32_t ItcmSingleErrorInfo
itcm single error information, user should parse it by themself.
-
uint32_t ItcmSingleErrorAddr
itcm single error address
-
uint32_t ItcmSingleErrorDataLSB
itcm single error data LSB
-
uint32_t ItcmSingleErrorDataMSB
itcm single error data MSB
-
uint32_t ItcmSingleErrorInfo
-
struct _flexram_itcm_ecc_multi_error_info
- #include <fsl_flexram.h>
FLEXRAM itcm ecc multiple error information, including multiple error information, error address, error data.
Public Members
-
uint32_t ItcmMultiErrorInfo
itcm multiple error information, user should parse it by themself.
-
uint32_t ItcmMultiErrorAddr
itcm multiple error address
-
uint32_t ItcmMultiErrorDataLSB
itcm multiple error data LSB
-
uint32_t ItcmMultiErrorDataMSB
itcm multiple error data MSB
-
uint32_t ItcmMultiErrorInfo
-
struct _flexram_dtcm_ecc_single_error_info
- #include <fsl_flexram.h>
FLEXRAM dtcm ecc single error information, including single error information, error address, error data.
Public Members
-
uint32_t DtcmSingleErrorInfo
dtcm single error information, user should parse it by themself.
-
uint32_t DtcmSingleErrorAddr
dtcm single error address
-
uint32_t DtcmSingleErrorData
dtcm single error data
-
uint32_t DtcmSingleErrorInfo
-
struct _flexram_dtcm_ecc_multi_error_info
- #include <fsl_flexram.h>
FLEXRAM dtcm ecc multiple error information, including multiple error information, error address, error data.
Public Members
-
uint32_t DtcmMultiErrorInfo
dtcm multiple error information, user should parse it by themself.
-
uint32_t DtcmMultiErrorAddr
dtcm multiple error address
-
uint32_t DtcmMultiErrorData
dtcm multiple error data
-
uint32_t DtcmMultiErrorInfo
FLEXSPI: Flexible Serial Peripheral Interface Driver
-
uint32_t FLEXSPI_GetInstance(FLEXSPI_Type *base)
Get the instance number for FLEXSPI.
- Parameters:
base – FLEXSPI base pointer.
-
status_t FLEXSPI_CheckAndClearError(FLEXSPI_Type *base, uint32_t status)
Check and clear IP command execution errors.
- Parameters:
base – FLEXSPI base pointer.
status – interrupt status.
-
void FLEXSPI_Init(FLEXSPI_Type *base, const flexspi_config_t *config)
Initializes the FLEXSPI module and internal state.
This function enables the clock for FLEXSPI and also configures the FLEXSPI with the input configure parameters. Users should call this function before any FLEXSPI operations.
- Parameters:
base – FLEXSPI peripheral base address.
config – FLEXSPI configure structure.
-
void FLEXSPI_GetDefaultConfig(flexspi_config_t *config)
Gets default settings for FLEXSPI.
- Parameters:
config – FLEXSPI configuration structure.
-
void FLEXSPI_Deinit(FLEXSPI_Type *base)
Deinitializes the FLEXSPI module.
Clears the FLEXSPI state and FLEXSPI module registers.
- Parameters:
base – FLEXSPI peripheral base address.
-
void FLEXSPI_UpdateDllValue(FLEXSPI_Type *base, flexspi_device_config_t *config, flexspi_port_t port)
Update FLEXSPI DLL value depending on currently flexspi root clock.
- Parameters:
base – FLEXSPI peripheral base address.
config – Flash configuration parameters.
port – FLEXSPI Operation port.
-
void FLEXSPI_SetFlashConfig(FLEXSPI_Type *base, flexspi_device_config_t *config, flexspi_port_t port)
Configures the connected device parameter.
This function configures the connected device relevant parameters, such as the size, command, and so on. The flash configuration value cannot have a default value. The user needs to configure it according to the connected device.
- Parameters:
base – FLEXSPI peripheral base address.
config – Flash configuration parameters.
port – FLEXSPI Operation port.
-
void FLEXSPI_SoftwareReset(FLEXSPI_Type *base)
Software reset for the FLEXSPI logic.
This function sets the software reset flags for both AHB and buffer domain and resets both AHB buffer and also IP FIFOs.
- Parameters:
base – FLEXSPI peripheral base address.
-
static inline void FLEXSPI_Enable(FLEXSPI_Type *base, bool enable)
Enables or disables the FLEXSPI module.
- Parameters:
base – FLEXSPI peripheral base address.
enable – True means enable FLEXSPI, false means disable.
-
static inline void FLEXSPI_EnableInterrupts(FLEXSPI_Type *base, uint32_t mask)
Enables the FLEXSPI interrupts.
- Parameters:
base – FLEXSPI peripheral base address.
mask – FLEXSPI interrupt source.
-
static inline void FLEXSPI_DisableInterrupts(FLEXSPI_Type *base, uint32_t mask)
Disable the FLEXSPI interrupts.
- Parameters:
base – FLEXSPI peripheral base address.
mask – FLEXSPI interrupt source.
-
static inline void FLEXSPI_EnableTxDMA(FLEXSPI_Type *base, bool enable)
Enables or disables FLEXSPI IP Tx FIFO DMA requests.
- Parameters:
base – FLEXSPI peripheral base address.
enable – Enable flag for transmit DMA request. Pass true for enable, false for disable.
-
static inline void FLEXSPI_EnableRxDMA(FLEXSPI_Type *base, bool enable)
Enables or disables FLEXSPI IP Rx FIFO DMA requests.
- Parameters:
base – FLEXSPI peripheral base address.
enable – Enable flag for receive DMA request. Pass true for enable, false for disable.
-
static inline uint32_t FLEXSPI_GetTxFifoAddress(FLEXSPI_Type *base)
Gets FLEXSPI IP tx fifo address for DMA transfer.
- Parameters:
base – FLEXSPI peripheral base address.
- Return values:
The – tx fifo address.
-
static inline uint32_t FLEXSPI_GetRxFifoAddress(FLEXSPI_Type *base)
Gets FLEXSPI IP rx fifo address for DMA transfer.
- Parameters:
base – FLEXSPI peripheral base address.
- Return values:
The – rx fifo address.
-
static inline void FLEXSPI_ResetFifos(FLEXSPI_Type *base, bool txFifo, bool rxFifo)
Clears the FLEXSPI IP FIFO logic.
- Parameters:
base – FLEXSPI peripheral base address.
txFifo – Pass true to reset TX FIFO.
rxFifo – Pass true to reset RX FIFO.
-
static inline void FLEXSPI_GetFifoCounts(FLEXSPI_Type *base, size_t *txCount, size_t *rxCount)
Gets the valid data entries in the FLEXSPI FIFOs.
- Parameters:
base – FLEXSPI peripheral base address.
txCount – [out] Pointer through which the current number of bytes in the transmit FIFO is returned. Pass NULL if this value is not required.
rxCount – [out] Pointer through which the current number of bytes in the receive FIFO is returned. Pass NULL if this value is not required.
-
static inline uint32_t FLEXSPI_GetInterruptStatusFlags(FLEXSPI_Type *base)
Get the FLEXSPI interrupt status flags.
- Parameters:
base – FLEXSPI peripheral base address.
- Return values:
interrupt – status flag, use status flag to AND flexspi_flags_t could get the related status.
-
static inline void FLEXSPI_ClearInterruptStatusFlags(FLEXSPI_Type *base, uint32_t mask)
Get the FLEXSPI interrupt status flags.
- Parameters:
base – FLEXSPI peripheral base address.
mask – FLEXSPI interrupt source.
-
static inline flexspi_arb_command_source_t FLEXSPI_GetArbitratorCommandSource(FLEXSPI_Type *base)
Gets the trigger source of current command sequence granted by arbitrator.
- Parameters:
base – FLEXSPI peripheral base address.
- Return values:
trigger – source of current command sequence.
-
static inline flexspi_ip_error_code_t FLEXSPI_GetIPCommandErrorCode(FLEXSPI_Type *base, uint8_t *index)
Gets the error code when IP command error detected.
- Parameters:
base – FLEXSPI peripheral base address.
index – Pointer to a uint8_t type variable to receive the sequence index when error detected.
- Return values:
error – code when IP command error detected.
-
static inline flexspi_ahb_error_code_t FLEXSPI_GetAHBCommandErrorCode(FLEXSPI_Type *base, uint8_t *index)
Gets the error code when AHB command error detected.
- Parameters:
base – FLEXSPI peripheral base address.
index – Pointer to a uint8_t type variable to receive the sequence index when error detected.
- Return values:
error – code when AHB command error detected.
-
static inline bool FLEXSPI_GetBusIdleStatus(FLEXSPI_Type *base)
Returns whether the bus is idle.
- Parameters:
base – FLEXSPI peripheral base address.
- Return values:
true – Bus is idle.
false – Bus is busy.
-
void FLEXSPI_UpdateRxSampleClock(FLEXSPI_Type *base, flexspi_read_sample_clock_t clockSource)
Update read sample clock source.
- Parameters:
base – FLEXSPI peripheral base address.
clockSource – clockSource of type flexspi_read_sample_clock_t
-
void FLEXSPI_UpdateLUT(FLEXSPI_Type *base, uint32_t index, const uint32_t *cmd, uint32_t count)
Updates the LUT table.
- Parameters:
base – FLEXSPI peripheral base address.
index – From which index start to update. It could be any index of the LUT table, which also allows user to update command content inside a command. Each command consists of up to 8 instructions and occupy 4*32-bit memory.
cmd – Command sequence array.
count – Number of sequences.
-
static inline void FLEXSPI_WriteData(FLEXSPI_Type *base, uint32_t data, uint8_t fifoIndex)
Writes data into FIFO.
- Parameters:
base – FLEXSPI peripheral base address
data – The data bytes to send
fifoIndex – Destination fifo index.
-
static inline uint32_t FLEXSPI_ReadData(FLEXSPI_Type *base, uint8_t fifoIndex)
Receives data from data FIFO.
- Parameters:
base – FLEXSPI peripheral base address
fifoIndex – Source fifo index.
- Returns:
The data in the FIFO.
-
status_t FLEXSPI_WriteBlocking(FLEXSPI_Type *base, uint8_t *buffer, size_t size)
Sends a buffer of data bytes using blocking method.
Note
This function blocks via polling until all bytes have been sent.
- Parameters:
base – FLEXSPI peripheral base address
buffer – The data bytes to send
size – The number of data bytes to send
- Return values:
kStatus_Success – write success without error
kStatus_FLEXSPI_SequenceExecutionTimeout – sequence execution timeout
kStatus_FLEXSPI_IpCommandSequenceError – IP command sequence error detected
kStatus_FLEXSPI_IpCommandGrantTimeout – IP command grant timeout detected
-
status_t FLEXSPI_ReadBlocking(FLEXSPI_Type *base, uint8_t *buffer, size_t size)
Receives a buffer of data bytes using a blocking method.
Note
This function blocks via polling until all bytes have been sent.
- Parameters:
base – FLEXSPI peripheral base address
buffer – The data bytes to send
size – The number of data bytes to receive
- Return values:
kStatus_Success – read success without error
kStatus_FLEXSPI_SequenceExecutionTimeout – sequence execution timeout
kStatus_FLEXSPI_IpCommandSequenceError – IP command sequencen error detected
kStatus_FLEXSPI_IpCommandGrantTimeout – IP command grant timeout detected
-
status_t FLEXSPI_TransferBlocking(FLEXSPI_Type *base, flexspi_transfer_t *xfer)
Execute command to transfer a buffer data bytes using a blocking method.
- Parameters:
base – FLEXSPI peripheral base address
xfer – pointer to the transfer structure.
- Return values:
kStatus_Success – command transfer success without error
kStatus_FLEXSPI_SequenceExecutionTimeout – sequence execution timeout
kStatus_FLEXSPI_IpCommandSequenceError – IP command sequence error detected
kStatus_FLEXSPI_IpCommandGrantTimeout – IP command grant timeout detected
-
void FLEXSPI_TransferCreateHandle(FLEXSPI_Type *base, flexspi_handle_t *handle, flexspi_transfer_callback_t callback, void *userData)
Initializes the FLEXSPI handle which is used in transactional functions.
- Parameters:
base – FLEXSPI peripheral base address.
handle – pointer to flexspi_handle_t structure to store the transfer state.
callback – pointer to user callback function.
userData – user parameter passed to the callback function.
-
status_t FLEXSPI_TransferNonBlocking(FLEXSPI_Type *base, flexspi_handle_t *handle, flexspi_transfer_t *xfer)
Performs a interrupt non-blocking transfer on the FLEXSPI bus.
Note
Calling the API returns immediately after transfer initiates. The user needs to call FLEXSPI_GetTransferCount to poll the transfer status to check whether the transfer is finished. If the return status is not kStatus_FLEXSPI_Busy, the transfer is finished. For FLEXSPI_Read, the dataSize should be multiple of rx watermark level, or FLEXSPI could not read data properly.
- Parameters:
base – FLEXSPI peripheral base address.
handle – pointer to flexspi_handle_t structure which stores the transfer state.
xfer – pointer to flexspi_transfer_t structure.
- Return values:
kStatus_Success – Successfully start the data transmission.
kStatus_FLEXSPI_Busy – Previous transmission still not finished.
-
status_t FLEXSPI_TransferGetCount(FLEXSPI_Type *base, flexspi_handle_t *handle, size_t *count)
Gets the master transfer status during a interrupt non-blocking transfer.
- Parameters:
base – FLEXSPI peripheral base address.
handle – pointer to flexspi_handle_t structure which stores the transfer state.
count – Number of bytes transferred so far by the non-blocking transaction.
- Return values:
kStatus_InvalidArgument – count is Invalid.
kStatus_Success – Successfully return the count.
-
void FLEXSPI_TransferAbort(FLEXSPI_Type *base, flexspi_handle_t *handle)
Aborts an interrupt non-blocking transfer early.
Note
This API can be called at any time when an interrupt non-blocking transfer initiates to abort the transfer early.
- Parameters:
base – FLEXSPI peripheral base address.
handle – pointer to flexspi_handle_t structure which stores the transfer state
-
void FLEXSPI_TransferHandleIRQ(FLEXSPI_Type *base, flexspi_handle_t *handle)
Master interrupt handler.
- Parameters:
base – FLEXSPI peripheral base address.
handle – pointer to flexspi_handle_t structure.
-
FSL_FLEXSPI_DRIVER_VERSION
FLEXSPI driver version.
Status structure of FLEXSPI.
Values:
-
enumerator kStatus_FLEXSPI_Busy
FLEXSPI is busy
-
enumerator kStatus_FLEXSPI_SequenceExecutionTimeout
Sequence execution timeout error occurred during FLEXSPI transfer.
-
enumerator kStatus_FLEXSPI_IpCommandSequenceError
IP command Sequence execution timeout error occurred during FLEXSPI transfer.
-
enumerator kStatus_FLEXSPI_IpCommandGrantTimeout
IP command grant timeout error occurred during FLEXSPI transfer.
-
enumerator kStatus_FLEXSPI_Busy
CMD definition of FLEXSPI, use to form LUT instruction, _flexspi_command.
Values:
-
enumerator kFLEXSPI_Command_STOP
Stop execution, deassert CS.
-
enumerator kFLEXSPI_Command_SDR
Transmit Command code to Flash, using SDR mode.
-
enumerator kFLEXSPI_Command_RADDR_SDR
Transmit Row Address to Flash, using SDR mode.
-
enumerator kFLEXSPI_Command_CADDR_SDR
Transmit Column Address to Flash, using SDR mode.
-
enumerator kFLEXSPI_Command_MODE1_SDR
Transmit 1-bit Mode bits to Flash, using SDR mode.
-
enumerator kFLEXSPI_Command_MODE2_SDR
Transmit 2-bit Mode bits to Flash, using SDR mode.
-
enumerator kFLEXSPI_Command_MODE4_SDR
Transmit 4-bit Mode bits to Flash, using SDR mode.
-
enumerator kFLEXSPI_Command_MODE8_SDR
Transmit 8-bit Mode bits to Flash, using SDR mode.
-
enumerator kFLEXSPI_Command_WRITE_SDR
Transmit Programming Data to Flash, using SDR mode.
-
enumerator kFLEXSPI_Command_READ_SDR
Receive Read Data from Flash, using SDR mode.
-
enumerator kFLEXSPI_Command_LEARN_SDR
Receive Read Data or Preamble bit from Flash, SDR mode.
-
enumerator kFLEXSPI_Command_DATSZ_SDR
Transmit Read/Program Data size (byte) to Flash, SDR mode.
-
enumerator kFLEXSPI_Command_DUMMY_SDR
Leave data lines undriven by FlexSPI controller.
-
enumerator kFLEXSPI_Command_DUMMY_RWDS_SDR
Leave data lines undriven by FlexSPI controller, dummy cycles decided by RWDS.
-
enumerator kFLEXSPI_Command_DDR
Transmit Command code to Flash, using DDR mode.
-
enumerator kFLEXSPI_Command_RADDR_DDR
Transmit Row Address to Flash, using DDR mode.
-
enumerator kFLEXSPI_Command_CADDR_DDR
Transmit Column Address to Flash, using DDR mode.
-
enumerator kFLEXSPI_Command_MODE1_DDR
Transmit 1-bit Mode bits to Flash, using DDR mode.
-
enumerator kFLEXSPI_Command_MODE2_DDR
Transmit 2-bit Mode bits to Flash, using DDR mode.
-
enumerator kFLEXSPI_Command_MODE4_DDR
Transmit 4-bit Mode bits to Flash, using DDR mode.
-
enumerator kFLEXSPI_Command_MODE8_DDR
Transmit 8-bit Mode bits to Flash, using DDR mode.
-
enumerator kFLEXSPI_Command_WRITE_DDR
Transmit Programming Data to Flash, using DDR mode.
-
enumerator kFLEXSPI_Command_READ_DDR
Receive Read Data from Flash, using DDR mode.
-
enumerator kFLEXSPI_Command_LEARN_DDR
Receive Read Data or Preamble bit from Flash, DDR mode.
-
enumerator kFLEXSPI_Command_DATSZ_DDR
Transmit Read/Program Data size (byte) to Flash, DDR mode.
-
enumerator kFLEXSPI_Command_DUMMY_DDR
Leave data lines undriven by FlexSPI controller.
-
enumerator kFLEXSPI_Command_DUMMY_RWDS_DDR
Leave data lines undriven by FlexSPI controller, dummy cycles decided by RWDS.
-
enumerator kFLEXSPI_Command_JUMP_ON_CS
Stop execution, deassert CS and save operand[7:0] as the instruction start pointer for next sequence
-
enumerator kFLEXSPI_Command_STOP
-
enum _flexspi_pad
pad definition of FLEXSPI, use to form LUT instruction.
Values:
-
enumerator kFLEXSPI_1PAD
Transmit command/address and transmit/receive data only through DATA0/DATA1.
-
enumerator kFLEXSPI_2PAD
Transmit command/address and transmit/receive data only through DATA[1:0].
-
enumerator kFLEXSPI_4PAD
Transmit command/address and transmit/receive data only through DATA[3:0].
-
enumerator kFLEXSPI_8PAD
Transmit command/address and transmit/receive data only through DATA[7:0].
-
enumerator kFLEXSPI_1PAD
-
enum _flexspi_flags
FLEXSPI interrupt status flags.
Values:
-
enumerator kFLEXSPI_SequenceExecutionTimeoutFlag
Sequence execution timeout.
-
enumerator kFLEXSPI_AhbBusErrorFlag
AHB Bus error flag.
-
enumerator kFLEXSPI_SckStoppedBecauseTxEmptyFlag
SCK is stopped during command sequence because Async TX FIFO empty.
-
enumerator kFLEXSPI_SckStoppedBecauseRxFullFlag
SCK is stopped during command sequence because Async RX FIFO full.
-
enumerator kFLEXSPI_IpTxFifoWatermarkEmptyFlag
IP TX FIFO WaterMark empty.
-
enumerator kFLEXSPI_IpRxFifoWatermarkAvailableFlag
IP RX FIFO WaterMark available.
-
enumerator kFLEXSPI_AhbCommandSequenceErrorFlag
AHB triggered Command Sequences Error.
-
enumerator kFLEXSPI_IpCommandSequenceErrorFlag
IP triggered Command Sequences Error.
-
enumerator kFLEXSPI_AhbCommandGrantTimeoutFlag
AHB triggered Command Sequences Grant Timeout.
-
enumerator kFLEXSPI_IpCommandGrantTimeoutFlag
IP triggered Command Sequences Grant Timeout.
-
enumerator kFLEXSPI_IpCommandExecutionDoneFlag
IP triggered Command Sequences Execution finished.
-
enumerator kFLEXSPI_AllInterruptFlags
All flags.
-
enumerator kFLEXSPI_SequenceExecutionTimeoutFlag
-
enum _flexspi_read_sample_clock
FLEXSPI sample clock source selection for Flash Reading.
Values:
-
enumerator kFLEXSPI_ReadSampleClkLoopbackInternally
Dummy Read strobe generated by FlexSPI Controller and loopback internally.
-
enumerator kFLEXSPI_ReadSampleClkLoopbackFromDqsPad
Dummy Read strobe generated by FlexSPI Controller and loopback from DQS pad.
-
enumerator kFLEXSPI_ReadSampleClkLoopbackFromSckPad
SCK output clock and loopback from SCK pad.
-
enumerator kFLEXSPI_ReadSampleClkExternalInputFromDqsPad
Flash provided Read strobe and input from DQS pad.
-
enumerator kFLEXSPI_ReadSampleClkLoopbackInternally
-
enum _flexspi_cs_interval_cycle_unit
FLEXSPI interval unit for flash device select.
Values:
-
enumerator kFLEXSPI_CsIntervalUnit1SckCycle
Chip selection interval: CSINTERVAL * 1 serial clock cycle.
-
enumerator kFLEXSPI_CsIntervalUnit256SckCycle
Chip selection interval: CSINTERVAL * 256 serial clock cycle.
-
enumerator kFLEXSPI_CsIntervalUnit1SckCycle
-
enum _flexspi_ahb_write_wait_unit
FLEXSPI AHB wait interval unit for writing.
Values:
-
enumerator kFLEXSPI_AhbWriteWaitUnit2AhbCycle
AWRWAIT unit is 2 ahb clock cycle.
-
enumerator kFLEXSPI_AhbWriteWaitUnit8AhbCycle
AWRWAIT unit is 8 ahb clock cycle.
-
enumerator kFLEXSPI_AhbWriteWaitUnit32AhbCycle
AWRWAIT unit is 32 ahb clock cycle.
-
enumerator kFLEXSPI_AhbWriteWaitUnit128AhbCycle
AWRWAIT unit is 128 ahb clock cycle.
-
enumerator kFLEXSPI_AhbWriteWaitUnit512AhbCycle
AWRWAIT unit is 512 ahb clock cycle.
-
enumerator kFLEXSPI_AhbWriteWaitUnit2048AhbCycle
AWRWAIT unit is 2048 ahb clock cycle.
-
enumerator kFLEXSPI_AhbWriteWaitUnit8192AhbCycle
AWRWAIT unit is 8192 ahb clock cycle.
-
enumerator kFLEXSPI_AhbWriteWaitUnit32768AhbCycle
AWRWAIT unit is 32768 ahb clock cycle.
-
enumerator kFLEXSPI_AhbWriteWaitUnit2AhbCycle
-
enum _flexspi_ip_error_code
Error Code when IP command Error detected.
Values:
-
enumerator kFLEXSPI_IpCmdErrorNoError
No error.
-
enumerator kFLEXSPI_IpCmdErrorJumpOnCsInIpCmd
IP command with JMP_ON_CS instruction used.
-
enumerator kFLEXSPI_IpCmdErrorUnknownOpCode
Unknown instruction opcode in the sequence.
-
enumerator kFLEXSPI_IpCmdErrorSdrDummyInDdrSequence
Instruction DUMMY_SDR/DUMMY_RWDS_SDR used in DDR sequence.
-
enumerator kFLEXSPI_IpCmdErrorDdrDummyInSdrSequence
Instruction DUMMY_DDR/DUMMY_RWDS_DDR used in SDR sequence.
-
enumerator kFLEXSPI_IpCmdErrorInvalidAddress
Flash access start address exceed the whole flash address range (A1/A2/B1/B2).
-
enumerator kFLEXSPI_IpCmdErrorSequenceExecutionTimeout
Sequence execution timeout.
-
enumerator kFLEXSPI_IpCmdErrorFlashBoundaryAcrosss
Flash boundary crossed.
-
enumerator kFLEXSPI_IpCmdErrorNoError
-
enum _flexspi_ahb_error_code
Error Code when AHB command Error detected.
Values:
-
enumerator kFLEXSPI_AhbCmdErrorNoError
No error.
-
enumerator kFLEXSPI_AhbCmdErrorJumpOnCsInWriteCmd
AHB Write command with JMP_ON_CS instruction used in the sequence.
-
enumerator kFLEXSPI_AhbCmdErrorUnknownOpCode
Unknown instruction opcode in the sequence.
-
enumerator kFLEXSPI_AhbCmdErrorSdrDummyInDdrSequence
Instruction DUMMY_SDR/DUMMY_RWDS_SDR used in DDR sequence.
-
enumerator kFLEXSPI_AhbCmdErrorDdrDummyInSdrSequence
Instruction DUMMY_DDR/DUMMY_RWDS_DDR used in SDR sequence.
-
enumerator kFLEXSPI_AhbCmdSequenceExecutionTimeout
Sequence execution timeout.
-
enumerator kFLEXSPI_AhbCmdErrorNoError
-
enum _flexspi_port
FLEXSPI operation port select.
Values:
-
enumerator kFLEXSPI_PortA1
Access flash on A1 port.
-
enumerator kFLEXSPI_PortA2
Access flash on A2 port.
-
enumerator kFLEXSPI_PortB1
Access flash on B1 port.
-
enumerator kFLEXSPI_PortB2
Access flash on B2 port.
-
enumerator kFLEXSPI_PortCount
-
enumerator kFLEXSPI_PortA1
-
enum _flexspi_arb_command_source
Trigger source of current command sequence granted by arbitrator.
Values:
-
enumerator kFLEXSPI_AhbReadCommand
-
enumerator kFLEXSPI_AhbWriteCommand
-
enumerator kFLEXSPI_IpCommand
-
enumerator kFLEXSPI_SuspendedCommand
-
enumerator kFLEXSPI_AhbReadCommand
-
enum _flexspi_command_type
Command type.
Values:
-
enumerator kFLEXSPI_Command
FlexSPI operation: Only command, both TX and Rx buffer are ignored.
-
enumerator kFLEXSPI_Config
FlexSPI operation: Configure device mode, the TX fifo size is fixed in LUT.
-
enumerator kFLEXSPI_Read
-
enumerator kFLEXSPI_Write
-
enumerator kFLEXSPI_Command
-
typedef enum _flexspi_pad flexspi_pad_t
pad definition of FLEXSPI, use to form LUT instruction.
-
typedef enum _flexspi_flags flexspi_flags_t
FLEXSPI interrupt status flags.
-
typedef enum _flexspi_read_sample_clock flexspi_read_sample_clock_t
FLEXSPI sample clock source selection for Flash Reading.
-
typedef enum _flexspi_cs_interval_cycle_unit flexspi_cs_interval_cycle_unit_t
FLEXSPI interval unit for flash device select.
-
typedef enum _flexspi_ahb_write_wait_unit flexspi_ahb_write_wait_unit_t
FLEXSPI AHB wait interval unit for writing.
-
typedef enum _flexspi_ip_error_code flexspi_ip_error_code_t
Error Code when IP command Error detected.
-
typedef enum _flexspi_ahb_error_code flexspi_ahb_error_code_t
Error Code when AHB command Error detected.
-
typedef enum _flexspi_port flexspi_port_t
FLEXSPI operation port select.
-
typedef enum _flexspi_arb_command_source flexspi_arb_command_source_t
Trigger source of current command sequence granted by arbitrator.
-
typedef enum _flexspi_command_type flexspi_command_type_t
Command type.
-
typedef struct _flexspi_ahbBuffer_config flexspi_ahbBuffer_config_t
-
typedef struct _flexspi_config flexspi_config_t
FLEXSPI configuration structure.
-
typedef struct _flexspi_device_config flexspi_device_config_t
External device configuration items.
-
typedef struct _flexspi_transfer flexspi_transfer_t
Transfer structure for FLEXSPI.
-
typedef struct _flexspi_handle flexspi_handle_t
-
typedef void (*flexspi_transfer_callback_t)(FLEXSPI_Type *base, flexspi_handle_t *handle, status_t status, void *userData)
FLEXSPI transfer callback function.
-
FSL_FEATURE_FLEXSPI_AHB_BUFFER_COUNT
-
FLEXSPI_LUT_SEQ(cmd0, pad0, op0, cmd1, pad1, op1)
Formula to form FLEXSPI instructions in LUT table.
-
struct _flexspi_ahbBuffer_config
- #include <fsl_flexspi.h>
Public Members
-
uint8_t priority
This priority for AHB Master Read which this AHB RX Buffer is assigned.
-
uint8_t masterIndex
AHB Master ID the AHB RX Buffer is assigned.
-
uint16_t bufferSize
AHB buffer size in byte.
-
bool enablePrefetch
AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master, allows prefetch disable/enable separately for each master.
-
uint8_t priority
-
struct _flexspi_config
- #include <fsl_flexspi.h>
FLEXSPI configuration structure.
Public Members
-
flexspi_read_sample_clock_t rxSampleClock
Sample Clock source selection for Flash Reading.
-
bool enableSckFreeRunning
Enable/disable SCK output free-running.
-
bool enableCombination
Enable/disable combining PORT A and B Data Pins (SIOA[3:0] and SIOB[3:0]) to support Flash Octal mode.
-
bool enableDoze
Enable/disable doze mode support.
-
bool enableHalfSpeedAccess
Enable/disable divide by 2 of the clock for half speed commands.
-
bool enableSckBDiffOpt
Enable/disable SCKB pad use as SCKA differential clock output, when enable, Port B flash access is not available.
-
bool enableSameConfigForAll
Enable/disable same configuration for all connected devices when enabled, same configuration in FLASHA1CRx is applied to all.
-
uint16_t seqTimeoutCycle
Timeout wait cycle for command sequence execution, timeout after ahbGrantTimeoutCyle*1024 serial root clock cycles.
-
uint8_t ipGrantTimeoutCycle
Timeout wait cycle for IP command grant, timeout after ipGrantTimeoutCycle*1024 AHB clock cycles.
-
uint8_t txWatermark
FLEXSPI IP transmit watermark value.
-
uint8_t rxWatermark
FLEXSPI receive watermark value.
-
flexspi_read_sample_clock_t rxSampleClock
-
struct _flexspi_device_config
- #include <fsl_flexspi.h>
External device configuration items.
Public Members
-
uint32_t flexspiRootClk
FLEXSPI serial root clock.
-
bool isSck2Enabled
FLEXSPI use SCK2.
-
uint32_t flashSize
Flash size in KByte.
-
bool addressShift
Address shift.
-
flexspi_cs_interval_cycle_unit_t CSIntervalUnit
CS interval unit, 1 or 256 cycle.
-
uint16_t CSInterval
CS line assert interval, multiply CS interval unit to get the CS line assert interval cycles.
-
uint8_t CSHoldTime
CS line hold time.
-
uint8_t CSSetupTime
CS line setup time.
-
uint8_t dataValidTime
Data valid time for external device.
-
uint8_t columnspace
Column space size.
-
bool enableWordAddress
If enable word address.
-
uint8_t AWRSeqIndex
Sequence ID for AHB write command.
-
uint8_t AWRSeqNumber
Sequence number for AHB write command.
-
uint8_t ARDSeqIndex
Sequence ID for AHB read command.
-
uint8_t ARDSeqNumber
Sequence number for AHB read command.
-
flexspi_ahb_write_wait_unit_t AHBWriteWaitUnit
AHB write wait unit.
-
uint16_t AHBWriteWaitInterval
AHB write wait interval, multiply AHB write interval unit to get the AHB write wait cycles.
-
bool enableWriteMask
Enable/Disable FLEXSPI drive DQS pin as write mask when writing to external device.
-
uint32_t flexspiRootClk
-
struct _flexspi_transfer
- #include <fsl_flexspi.h>
Transfer structure for FLEXSPI.
Public Members
-
uint32_t deviceAddress
Operation device address.
-
flexspi_port_t port
Operation port.
-
flexspi_command_type_t cmdType
Execution command type.
-
uint8_t seqIndex
Sequence ID for command.
-
uint8_t SeqNumber
Sequence number for command.
-
uint32_t *data
Data buffer.
-
size_t dataSize
Data size in bytes.
-
uint32_t deviceAddress
-
struct _flexspi_handle
- #include <fsl_flexspi.h>
Transfer handle structure for FLEXSPI.
Public Members
-
uint32_t state
Internal state for FLEXSPI transfer
-
uint8_t *data
Data buffer.
-
size_t dataSize
Remaining Data size in bytes.
-
size_t transferTotalSize
Total Data size in bytes.
-
flexspi_transfer_callback_t completionCallback
Callback for users while transfer finish or error occurred
-
void *userData
FLEXSPI callback function parameter.
-
uint32_t state
-
struct ahbConfig
Public Members
-
uint8_t ahbGrantTimeoutCycle
Timeout wait cycle for AHB command grant, timeout after ahbGrantTimeoutCyle*1024 AHB clock cycles.
-
uint16_t ahbBusTimeoutCycle
Timeout wait cycle for AHB read/write access, timeout after ahbBusTimeoutCycle*1024 AHB clock cycles.
-
uint8_t resumeWaitCycle
Wait cycle for idle state before suspended command sequence resume, timeout after ahbBusTimeoutCycle AHB clock cycles.
-
flexspi_ahbBuffer_config_t buffer[FSL_FEATURE_FLEXSPI_AHB_BUFFER_COUNTn(0)]
AHB buffer size.
-
bool enableClearAHBBufferOpt
Enable/disable automatically clean AHB RX Buffer and TX Buffer when FLEXSPI returns STOP mode ACK.
-
bool enableReadAddressOpt
Enable/disable remove AHB read burst start address alignment limitation. when enable, there is no AHB read burst start address alignment limitation.
-
bool enableAHBPrefetch
Enable/disable AHB read prefetch feature, when enabled, FLEXSPI will fetch more data than current AHB burst.
-
bool enableAHBBufferable
Enable/disable AHB bufferable write access support, when enabled, FLEXSPI return before waiting for command execution finished.
-
bool enableAHBCachable
Enable AHB bus cachable read access support.
-
uint8_t ahbGrantTimeoutCycle
FLEXSPI eDMA Driver
-
void FLEXSPI_TransferCreateHandleEDMA(FLEXSPI_Type *base, flexspi_edma_handle_t *handle, flexspi_edma_callback_t callback, void *userData, edma_handle_t *txDmaHandle, edma_handle_t *rxDmaHandle)
Initializes the FLEXSPI handle for transfer which is used in transactional functions and set the callback.
- Parameters:
base – FLEXSPI peripheral base address
handle – Pointer to flexspi_edma_handle_t structure
callback – FLEXSPI callback, NULL means no callback.
userData – User callback function data.
txDmaHandle – User requested DMA handle for TX DMA transfer.
rxDmaHandle – User requested DMA handle for RX DMA transfer.
-
void FLEXSPI_TransferUpdateSizeEDMA(FLEXSPI_Type *base, flexspi_edma_handle_t *handle, flexspi_edma_transfer_nsize_t nsize)
Update FLEXSPI EDMA transfer source data transfer size(SSIZE) and destination data transfer size(DSIZE).
See also
flexspi_edma_transfer_nsize_t .
- Parameters:
base – FLEXSPI peripheral base address
handle – Pointer to flexspi_edma_handle_t structure
nsize – FLEXSPI DMA transfer data transfer size(SSIZE/DSIZE), by default the size is kFLEXPSI_EDMAnSize1Bytes(one byte).
-
status_t FLEXSPI_TransferEDMA(FLEXSPI_Type *base, flexspi_edma_handle_t *handle, flexspi_transfer_t *xfer)
Transfers FLEXSPI data using an eDMA non-blocking method.
This function writes/receives data to/from the FLEXSPI transmit/receive FIFO. This function is non-blocking.
- Parameters:
base – FLEXSPI peripheral base address.
handle – Pointer to flexspi_edma_handle_t structure
xfer – FLEXSPI transfer structure.
- Return values:
kStatus_FLEXSPI_Busy – FLEXSPI is busy transfer.
kStatus_InvalidArgument – The watermark configuration is invalid, the watermark should be power of 2 to do successfully EDMA transfer.
kStatus_Success – FLEXSPI successfully start edma transfer.
-
void FLEXSPI_TransferAbortEDMA(FLEXSPI_Type *base, flexspi_edma_handle_t *handle)
Aborts the transfer data using eDMA.
This function aborts the transfer data using eDMA.
- Parameters:
base – FLEXSPI peripheral base address.
handle – Pointer to flexspi_edma_handle_t structure
-
status_t FLEXSPI_TransferGetTransferCountEDMA(FLEXSPI_Type *base, flexspi_edma_handle_t *handle, size_t *count)
Gets the transferred counts of transfer.
- Parameters:
base – FLEXSPI peripheral base address.
handle – Pointer to flexspi_edma_handle_t structure.
count – Bytes transfer.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is not a non-blocking transaction currently in progress.
-
FSL_FLEXSPI_EDMA_DRIVER_VERSION
FLEXSPI EDMA driver version.
-
enum _flexspi_edma_ntransfer_size
eDMA transfer configuration
Values:
-
enumerator kFLEXPSI_EDMAnSize1Bytes
Source/Destination data transfer size is 1 byte every time
-
enumerator kFLEXPSI_EDMAnSize2Bytes
Source/Destination data transfer size is 2 bytes every time
-
enumerator kFLEXPSI_EDMAnSize4Bytes
Source/Destination data transfer size is 4 bytes every time
-
enumerator kFLEXPSI_EDMAnSize8Bytes
Source/Destination data transfer size is 8 bytes every time
-
enumerator kFLEXPSI_EDMAnSize32Bytes
Source/Destination data transfer size is 32 bytes every time
-
enumerator kFLEXPSI_EDMAnSize1Bytes
-
typedef struct _flexspi_edma_handle flexspi_edma_handle_t
-
typedef void (*flexspi_edma_callback_t)(FLEXSPI_Type *base, flexspi_edma_handle_t *handle, status_t status, void *userData)
FLEXSPI eDMA transfer callback function for finish and error.
-
typedef enum _flexspi_edma_ntransfer_size flexspi_edma_transfer_nsize_t
eDMA transfer configuration
-
struct _flexspi_edma_handle
- #include <fsl_flexspi_edma.h>
FLEXSPI DMA transfer handle, users should not touch the content of the handle.
Public Members
-
edma_handle_t *txDmaHandle
eDMA handler for FLEXSPI Tx.
-
edma_handle_t *rxDmaHandle
eDMA handler for FLEXSPI Rx.
-
size_t transferSize
Bytes need to transfer.
-
flexspi_edma_transfer_nsize_t nsize
eDMA SSIZE/DSIZE in each transfer.
-
uint8_t nbytes
eDMA minor byte transfer count initially configured.
-
uint8_t count
The transfer data count in a DMA request.
-
uint32_t state
Internal state for FLEXSPI eDMA transfer.
-
flexspi_edma_callback_t completionCallback
A callback function called after the eDMA transfer is finished.
-
void *userData
User callback parameter
-
edma_handle_t *txDmaHandle
GPC: General Power Controller Driver
-
FSL_GPC_DRIVER_VERSION
GPC driver version 2.1.1.
-
static inline void GPC_AllowIRQs(GPC_Type *base)
Allow all the IRQ/Events within the charge of GPC.
- Parameters:
base – GPC peripheral base address.
-
static inline void GPC_DisallowIRQs(GPC_Type *base)
Disallow all the IRQ/Events within the charge of GPC.
- Parameters:
base – GPC peripheral base address.
-
void GPC_EnableIRQ(GPC_Type *base, uint32_t irqId)
Enable the IRQ.
- Parameters:
base – GPC peripheral base address.
irqId – ID number of IRQ to be enabled, available range is 32-159. 0-31 is available in some platforms.
-
void GPC_DisableIRQ(GPC_Type *base, uint32_t irqId)
Disable the IRQ.
- Parameters:
base – GPC peripheral base address.
irqId – ID number of IRQ to be disabled, available range is 32-159. 0-31 is available in some platforms.
-
bool GPC_GetIRQStatusFlag(GPC_Type *base, uint32_t irqId)
Get the IRQ/Event flag.
- Parameters:
base – GPC peripheral base address.
irqId – ID number of IRQ to be enabled, available range is 32-159. 0-31 is available in some platforms.
- Returns:
Indicated IRQ/Event is asserted or not.
-
static inline void GPC_RequestL2CachePowerDown(GPC_Type *base, bool enable)
L2 Cache Power Gate Enable.
This function configures the L2 cache if it will keep power when in low power mode. When the L2 cache power is OFF, L2 cache will be power down once when CPU core is power down and will be hardware invalidated automatically when CPU core is re-power up. When the L2 cache power is ON, L2 cache will keep power on even if CPU core is power down and will not be hardware invalidated. When CPU core is re-power up, the default setting is OFF.
- Parameters:
base – GPC peripheral base address.
enable – Enable the request or not.
-
static inline void GPC_RequestPdram0PowerDown(GPC_Type *base, bool enable)
FLEXRAM PDRAM0 Power Gate Enable.
This function configures the FLEXRAM PDRAM0 if it will keep power when cpu core is power down. When the PDRAM0 Power is 1, PDRAM0 will be power down once when CPU core is power down. When the PDRAM0 Power is 0, PDRAM0 will keep power on even if CPU core is power down. When CPU core is re-power up, the default setting is 1.
- Parameters:
base – GPC peripheral base address.
enable – Enable the request or not.
-
static inline void GPC_RequestVADCPowerDown(GPC_Type *base, bool enable)
VADC power down.
This function requests the VADC power down.
- Parameters:
base – GPC peripheral base address.
enable – Enable the request or not.
-
static inline bool GPC_GetVADCPowerDownFlag(GPC_Type *base)
Checks if the VADC is power off.
- Parameters:
base – GPC peripheral base address.
- Returns:
Whether the VADC is power off or not.
-
static inline bool GPC_HasDVFS0ChangeRequest(GPC_Type *base)
Checks if the DVFS0 is requesting for frequency/voltage update.
- Parameters:
base – GPC peripheral base address.
- Returns:
Whether the DVFS0 is requesting for frequency/voltage update.
-
static inline void GPC_RequestDisplayPowerOn(GPC_Type *base, bool enable)
Requests the display power switch sequence.
- Parameters:
base – GPC peripheral base address.
enable – Enable the power on sequence, or the power down sequence.
-
static inline void GPC_RequestMEGAPowerOn(GPC_Type *base, bool enable)
Requests the MEGA power switch sequence.
- Parameters:
base – GPC peripheral base address.
enable – Enable the power on sequence, or the power down sequence.
GPIO: General-Purpose Input/Output Driver
-
void GPIO_PinInit(GPIO_Type *base, uint32_t pin, const gpio_pin_config_t *Config)
Initializes the GPIO peripheral according to the specified parameters in the initConfig.
- Parameters:
base – GPIO base pointer.
pin – Specifies the pin number
Config – pointer to a gpio_pin_config_t structure that contains the configuration information.
-
void GPIO_PinWrite(GPIO_Type *base, uint32_t pin, uint8_t output)
Sets the output level of the individual GPIO pin to logic 1 or 0.
- Parameters:
base – GPIO base pointer.
pin – GPIO port pin number.
output – GPIOpin output logic level.
0: corresponding pin output low-logic level.
1: corresponding pin output high-logic level.
-
static inline void GPIO_WritePinOutput(GPIO_Type *base, uint32_t pin, uint8_t output)
Sets the output level of the individual GPIO pin to logic 1 or 0.
- Deprecated:
Do not use this function. It has been superceded by GPIO_PinWrite.
-
static inline void GPIO_PortSet(GPIO_Type *base, uint32_t mask)
Sets the output level of the multiple GPIO pins to the logic 1.
- Parameters:
base – GPIO peripheral base pointer (GPIO1, GPIO2, GPIO3, and so on.)
mask – GPIO pin number macro
-
static inline void GPIO_SetPinsOutput(GPIO_Type *base, uint32_t mask)
Sets the output level of the multiple GPIO pins to the logic 1.
- Deprecated:
Do not use this function. It has been superceded by GPIO_PortSet.
-
static inline void GPIO_PortClear(GPIO_Type *base, uint32_t mask)
Sets the output level of the multiple GPIO pins to the logic 0.
- Parameters:
base – GPIO peripheral base pointer (GPIO1, GPIO2, GPIO3, and so on.)
mask – GPIO pin number macro
-
static inline void GPIO_ClearPinsOutput(GPIO_Type *base, uint32_t mask)
Sets the output level of the multiple GPIO pins to the logic 0.
- Deprecated:
Do not use this function. It has been superceded by GPIO_PortClear.
-
static inline void GPIO_PortToggle(GPIO_Type *base, uint32_t mask)
Reverses the current output logic of the multiple GPIO pins.
- Parameters:
base – GPIO peripheral base pointer (GPIO1, GPIO2, GPIO3, and so on.)
mask – GPIO pin number macro
-
static inline uint32_t GPIO_PinRead(GPIO_Type *base, uint32_t pin)
Reads the current input value of the GPIO port.
- Parameters:
base – GPIO base pointer.
pin – GPIO port pin number.
- Return values:
GPIO – port input value.
-
static inline uint32_t GPIO_ReadPinInput(GPIO_Type *base, uint32_t pin)
Reads the current input value of the GPIO port.
- Deprecated:
Do not use this function. It has been superceded by GPIO_PinRead.
-
static inline uint8_t GPIO_PinReadPadStatus(GPIO_Type *base, uint32_t pin)
Reads the current GPIO pin pad status.
- Parameters:
base – GPIO base pointer.
pin – GPIO port pin number.
- Return values:
GPIO – pin pad status value.
-
static inline uint8_t GPIO_ReadPadStatus(GPIO_Type *base, uint32_t pin)
Reads the current GPIO pin pad status.
- Deprecated:
Do not use this function. It has been superceded by GPIO_PinReadPadStatus.
-
void GPIO_PinSetInterruptConfig(GPIO_Type *base, uint32_t pin, gpio_interrupt_mode_t pinInterruptMode)
Sets the current pin interrupt mode.
- Parameters:
base – GPIO base pointer.
pin – GPIO port pin number.
pinInterruptMode – pointer to a gpio_interrupt_mode_t structure that contains the interrupt mode information.
-
static inline void GPIO_SetPinInterruptConfig(GPIO_Type *base, uint32_t pin, gpio_interrupt_mode_t pinInterruptMode)
Sets the current pin interrupt mode.
- Deprecated:
Do not use this function. It has been superceded by GPIO_PinSetInterruptConfig.
-
static inline void GPIO_PortEnableInterrupts(GPIO_Type *base, uint32_t mask)
Enables the specific pin interrupt.
- Parameters:
base – GPIO base pointer.
mask – GPIO pin number macro.
-
static inline void GPIO_EnableInterrupts(GPIO_Type *base, uint32_t mask)
Enables the specific pin interrupt.
- Parameters:
base – GPIO base pointer.
mask – GPIO pin number macro.
-
static inline void GPIO_PortDisableInterrupts(GPIO_Type *base, uint32_t mask)
Disables the specific pin interrupt.
- Parameters:
base – GPIO base pointer.
mask – GPIO pin number macro.
-
static inline void GPIO_DisableInterrupts(GPIO_Type *base, uint32_t mask)
Disables the specific pin interrupt.
- Deprecated:
Do not use this function. It has been superceded by GPIO_PortDisableInterrupts.
-
static inline uint32_t GPIO_PortGetInterruptFlags(GPIO_Type *base)
Reads individual pin interrupt status.
- Parameters:
base – GPIO base pointer.
- Return values:
current – pin interrupt status flag.
-
static inline uint32_t GPIO_GetPinsInterruptFlags(GPIO_Type *base)
Reads individual pin interrupt status.
- Parameters:
base – GPIO base pointer.
- Return values:
current – pin interrupt status flag.
-
static inline void GPIO_PortClearInterruptFlags(GPIO_Type *base, uint32_t mask)
Clears pin interrupt flag. Status flags are cleared by writing a 1 to the corresponding bit position.
- Parameters:
base – GPIO base pointer.
mask – GPIO pin number macro.
-
static inline void GPIO_ClearPinsInterruptFlags(GPIO_Type *base, uint32_t mask)
Clears pin interrupt flag. Status flags are cleared by writing a 1 to the corresponding bit position.
- Parameters:
base – GPIO base pointer.
mask – GPIO pin number macro.
-
FSL_GPIO_DRIVER_VERSION
GPIO driver version.
-
enum _gpio_pin_direction
GPIO direction definition.
Values:
-
enumerator kGPIO_DigitalInput
Set current pin as digital input.
-
enumerator kGPIO_DigitalOutput
Set current pin as digital output.
-
enumerator kGPIO_DigitalInput
-
enum _gpio_interrupt_mode
GPIO interrupt mode definition.
Values:
-
enumerator kGPIO_NoIntmode
Set current pin general IO functionality.
-
enumerator kGPIO_IntLowLevel
Set current pin interrupt is low-level sensitive.
-
enumerator kGPIO_IntHighLevel
Set current pin interrupt is high-level sensitive.
-
enumerator kGPIO_IntRisingEdge
Set current pin interrupt is rising-edge sensitive.
-
enumerator kGPIO_IntFallingEdge
Set current pin interrupt is falling-edge sensitive.
-
enumerator kGPIO_IntRisingOrFallingEdge
Enable the edge select bit to override the ICR register’s configuration.
-
enumerator kGPIO_NoIntmode
-
typedef enum _gpio_pin_direction gpio_pin_direction_t
GPIO direction definition.
-
typedef enum _gpio_interrupt_mode gpio_interrupt_mode_t
GPIO interrupt mode definition.
-
typedef struct _gpio_pin_config gpio_pin_config_t
GPIO Init structure definition.
-
struct _gpio_pin_config
- #include <fsl_gpio.h>
GPIO Init structure definition.
Public Members
-
gpio_pin_direction_t direction
Specifies the pin direction.
-
uint8_t outputLogic
Set a default output logic, which has no use in input
-
gpio_interrupt_mode_t interruptMode
Specifies the pin interrupt mode, a value of gpio_interrupt_mode_t.
-
gpio_pin_direction_t direction
GPT: General Purpose Timer
-
void GPT_Init(GPT_Type *base, const gpt_config_t *initConfig)
Initialize GPT to reset state and initialize running mode.
- Parameters:
base – GPT peripheral base address.
initConfig – GPT mode setting configuration.
-
void GPT_Deinit(GPT_Type *base)
Disables the module and gates the GPT clock.
- Parameters:
base – GPT peripheral base address.
-
void GPT_GetDefaultConfig(gpt_config_t *config)
Fills in the GPT configuration structure with default settings.
The default values are:
config->clockSource = kGPT_ClockSource_Periph; config->divider = 1U; config->enableRunInStop = true; config->enableRunInWait = true; config->enableRunInDoze = false; config->enableRunInDbg = false; config->enableFreeRun = false; config->enableMode = true;
- Parameters:
config – Pointer to the user configuration structure.
-
static inline void GPT_SoftwareReset(GPT_Type *base)
Software reset of GPT module.
- Parameters:
base – GPT peripheral base address.
-
static inline void GPT_SetClockSource(GPT_Type *base, gpt_clock_source_t gptClkSource)
Set clock source of GPT.
- Parameters:
base – GPT peripheral base address.
gptClkSource – Clock source (see gpt_clock_source_t typedef enumeration).
-
static inline gpt_clock_source_t GPT_GetClockSource(GPT_Type *base)
Get clock source of GPT.
- Parameters:
base – GPT peripheral base address.
- Returns:
clock source (see gpt_clock_source_t typedef enumeration).
-
static inline void GPT_SetClockDivider(GPT_Type *base, uint32_t divider)
Set pre scaler of GPT.
- Parameters:
base – GPT peripheral base address.
divider – Divider of GPT (1-4096).
-
static inline uint32_t GPT_GetClockDivider(GPT_Type *base)
Get clock divider in GPT module.
- Parameters:
base – GPT peripheral base address.
- Returns:
clock divider in GPT module (1-4096).
-
static inline void GPT_SetOscClockDivider(GPT_Type *base, uint32_t divider)
OSC 24M pre-scaler before selected by clock source.
- Parameters:
base – GPT peripheral base address.
divider – OSC Divider(1-16).
-
static inline uint32_t GPT_GetOscClockDivider(GPT_Type *base)
Get OSC 24M clock divider in GPT module.
- Parameters:
base – GPT peripheral base address.
- Returns:
OSC clock divider in GPT module (1-16).
-
static inline void GPT_StartTimer(GPT_Type *base)
Start GPT timer.
- Parameters:
base – GPT peripheral base address.
-
static inline void GPT_StopTimer(GPT_Type *base)
Stop GPT timer.
- Parameters:
base – GPT peripheral base address.
-
static inline uint32_t GPT_GetCurrentTimerCount(GPT_Type *base)
Reads the current GPT counting value.
- Parameters:
base – GPT peripheral base address.
- Returns:
Current GPT counter value.
-
static inline void GPT_SetInputOperationMode(GPT_Type *base, gpt_input_capture_channel_t channel, gpt_input_operation_mode_t mode)
Set GPT operation mode of input capture channel.
- Parameters:
base – GPT peripheral base address.
channel – GPT capture channel (see gpt_input_capture_channel_t typedef enumeration).
mode – GPT input capture operation mode (see gpt_input_operation_mode_t typedef enumeration).
-
static inline gpt_input_operation_mode_t GPT_GetInputOperationMode(GPT_Type *base, gpt_input_capture_channel_t channel)
Get GPT operation mode of input capture channel.
- Parameters:
base – GPT peripheral base address.
channel – GPT capture channel (see gpt_input_capture_channel_t typedef enumeration).
- Returns:
GPT input capture operation mode (see gpt_input_operation_mode_t typedef enumeration).
-
static inline uint32_t GPT_GetInputCaptureValue(GPT_Type *base, gpt_input_capture_channel_t channel)
Get GPT input capture value of certain channel.
- Parameters:
base – GPT peripheral base address.
channel – GPT capture channel (see gpt_input_capture_channel_t typedef enumeration).
- Returns:
GPT input capture value.
-
static inline void GPT_SetOutputOperationMode(GPT_Type *base, gpt_output_compare_channel_t channel, gpt_output_operation_mode_t mode)
Set GPT operation mode of output compare channel.
- Parameters:
base – GPT peripheral base address.
channel – GPT output compare channel (see gpt_output_compare_channel_t typedef enumeration).
mode – GPT output operation mode (see gpt_output_operation_mode_t typedef enumeration).
-
static inline gpt_output_operation_mode_t GPT_GetOutputOperationMode(GPT_Type *base, gpt_output_compare_channel_t channel)
Get GPT operation mode of output compare channel.
- Parameters:
base – GPT peripheral base address.
channel – GPT output compare channel (see gpt_output_compare_channel_t typedef enumeration).
- Returns:
GPT output operation mode (see gpt_output_operation_mode_t typedef enumeration).
-
static inline void GPT_SetOutputCompareValue(GPT_Type *base, gpt_output_compare_channel_t channel, uint32_t value)
Set GPT output compare value of output compare channel.
- Parameters:
base – GPT peripheral base address.
channel – GPT output compare channel (see gpt_output_compare_channel_t typedef enumeration).
value – GPT output compare value.
-
static inline uint32_t GPT_GetOutputCompareValue(GPT_Type *base, gpt_output_compare_channel_t channel)
Get GPT output compare value of output compare channel.
- Parameters:
base – GPT peripheral base address.
channel – GPT output compare channel (see gpt_output_compare_channel_t typedef enumeration).
- Returns:
GPT output compare value.
-
static inline void GPT_ForceOutput(GPT_Type *base, gpt_output_compare_channel_t channel)
Force GPT output action on output compare channel, ignoring comparator.
- Parameters:
base – GPT peripheral base address.
channel – GPT output compare channel (see gpt_output_compare_channel_t typedef enumeration).
-
static inline void GPT_EnableInterrupts(GPT_Type *base, uint32_t mask)
Enables the selected GPT interrupts.
- Parameters:
base – GPT peripheral base address.
mask – The interrupts to enable. This is a logical OR of members of the enumeration gpt_interrupt_enable_t
-
static inline void GPT_DisableInterrupts(GPT_Type *base, uint32_t mask)
Disables the selected GPT interrupts.
- Parameters:
base – GPT peripheral base address
mask – The interrupts to disable. This is a logical OR of members of the enumeration gpt_interrupt_enable_t
-
static inline uint32_t GPT_GetEnabledInterrupts(GPT_Type *base)
Gets the enabled GPT interrupts.
- Parameters:
base – GPT peripheral base address
- Returns:
The enabled interrupts. This is the logical OR of members of the enumeration gpt_interrupt_enable_t
-
static inline uint32_t GPT_GetStatusFlags(GPT_Type *base, gpt_status_flag_t flags)
Get GPT status flags.
- Parameters:
base – GPT peripheral base address.
flags – GPT status flag mask (see gpt_status_flag_t for bit definition).
- Returns:
GPT status, each bit represents one status flag.
-
static inline void GPT_ClearStatusFlags(GPT_Type *base, gpt_status_flag_t flags)
Clears the GPT status flags.
- Parameters:
base – GPT peripheral base address.
flags – GPT status flag mask (see gpt_status_flag_t for bit definition).
-
FSL_GPT_DRIVER_VERSION
-
enum _gpt_clock_source
List of clock sources.
Note
Actual number of clock sources is SoC dependent
Values:
-
enumerator kGPT_ClockSource_Off
GPT Clock Source Off.
-
enumerator kGPT_ClockSource_Periph
GPT Clock Source from Peripheral Clock.
-
enumerator kGPT_ClockSource_HighFreq
GPT Clock Source from High Frequency Reference Clock.
-
enumerator kGPT_ClockSource_Ext
GPT Clock Source from external pin.
-
enumerator kGPT_ClockSource_LowFreq
GPT Clock Source from Low Frequency Reference Clock.
-
enumerator kGPT_ClockSource_Osc
GPT Clock Source from Crystal oscillator.
-
enumerator kGPT_ClockSource_Off
-
enum _gpt_input_capture_channel
List of input capture channel number.
Values:
-
enumerator kGPT_InputCapture_Channel1
GPT Input Capture Channel1.
-
enumerator kGPT_InputCapture_Channel2
GPT Input Capture Channel2.
-
enumerator kGPT_InputCapture_Channel1
-
enum _gpt_input_operation_mode
List of input capture operation mode.
Values:
-
enumerator kGPT_InputOperation_Disabled
Don’t capture.
-
enumerator kGPT_InputOperation_RiseEdge
Capture on rising edge of input pin.
-
enumerator kGPT_InputOperation_FallEdge
Capture on falling edge of input pin.
-
enumerator kGPT_InputOperation_BothEdge
Capture on both edges of input pin.
-
enumerator kGPT_InputOperation_Disabled
-
enum _gpt_output_compare_channel
List of output compare channel number.
Values:
-
enumerator kGPT_OutputCompare_Channel1
Output Compare Channel1.
-
enumerator kGPT_OutputCompare_Channel2
Output Compare Channel2.
-
enumerator kGPT_OutputCompare_Channel3
Output Compare Channel3.
-
enumerator kGPT_OutputCompare_Channel1
-
enum _gpt_output_operation_mode
List of output compare operation mode.
Values:
-
enumerator kGPT_OutputOperation_Disconnected
Don’t change output pin.
-
enumerator kGPT_OutputOperation_Toggle
Toggle output pin.
-
enumerator kGPT_OutputOperation_Clear
Set output pin low.
-
enumerator kGPT_OutputOperation_Set
Set output pin high.
-
enumerator kGPT_OutputOperation_Activelow
Generate a active low pulse on output pin.
-
enumerator kGPT_OutputOperation_Disconnected
-
enum _gpt_interrupt_enable
List of GPT interrupts.
Values:
-
enumerator kGPT_OutputCompare1InterruptEnable
Output Compare Channel1 interrupt enable
-
enumerator kGPT_OutputCompare2InterruptEnable
Output Compare Channel2 interrupt enable
-
enumerator kGPT_OutputCompare3InterruptEnable
Output Compare Channel3 interrupt enable
-
enumerator kGPT_InputCapture1InterruptEnable
Input Capture Channel1 interrupt enable
-
enumerator kGPT_InputCapture2InterruptEnable
Input Capture Channel1 interrupt enable
-
enumerator kGPT_RollOverFlagInterruptEnable
Counter rolled over interrupt enable
-
enumerator kGPT_OutputCompare1InterruptEnable
-
enum _gpt_status_flag
Status flag.
Values:
-
enumerator kGPT_OutputCompare1Flag
Output compare channel 1 event.
-
enumerator kGPT_OutputCompare2Flag
Output compare channel 2 event.
-
enumerator kGPT_OutputCompare3Flag
Output compare channel 3 event.
-
enumerator kGPT_InputCapture1Flag
Input Capture channel 1 event.
-
enumerator kGPT_InputCapture2Flag
Input Capture channel 2 event.
-
enumerator kGPT_RollOverFlag
Counter reaches maximum value and rolled over to 0 event.
-
enumerator kGPT_OutputCompare1Flag
-
typedef enum _gpt_clock_source gpt_clock_source_t
List of clock sources.
Note
Actual number of clock sources is SoC dependent
-
typedef enum _gpt_input_capture_channel gpt_input_capture_channel_t
List of input capture channel number.
-
typedef enum _gpt_input_operation_mode gpt_input_operation_mode_t
List of input capture operation mode.
-
typedef enum _gpt_output_compare_channel gpt_output_compare_channel_t
List of output compare channel number.
-
typedef enum _gpt_output_operation_mode gpt_output_operation_mode_t
List of output compare operation mode.
-
typedef enum _gpt_interrupt_enable gpt_interrupt_enable_t
List of GPT interrupts.
-
typedef enum _gpt_status_flag gpt_status_flag_t
Status flag.
-
typedef struct _gpt_init_config gpt_config_t
Structure to configure the running mode.
-
struct _gpt_init_config
- #include <fsl_gpt.h>
Structure to configure the running mode.
Public Members
-
gpt_clock_source_t clockSource
clock source for GPT module.
-
uint32_t divider
clock divider (prescaler+1) from clock source to counter.
-
bool enableFreeRun
true: FreeRun mode, false: Restart mode.
-
bool enableRunInWait
GPT enabled in wait mode.
-
bool enableRunInStop
GPT enabled in stop mode.
-
bool enableRunInDoze
GPT enabled in doze mode.
-
bool enableRunInDbg
GPT enabled in debug mode.
-
bool enableMode
true: counter reset to 0 when enabled; false: counter retain its value when enabled.
-
gpt_clock_source_t clockSource
IOMUXC: IOMUX Controller
-
enum _iomuxc_gpr_mode
Values:
-
enumerator kIOMUXC_GPR_GlobalInterruptRequest
-
enumerator kIOMUXC_GPR_ENET1RefClkMode
-
enumerator kIOMUXC_GPR_ENET1TxClkOutputDir
-
enumerator kIOMUXC_GPR_SAI1MClkOutputDir
-
enumerator kIOMUXC_GPR_SAI2MClkOutputDir
-
enumerator kIOMUXC_GPR_SAI3MClkOutputDir
-
enumerator kIOMUXC_GPR_ExcMonitorSlavErrResponse
-
enumerator kIOMUXC_GPR_AHBClockEnable
-
enumerator kIOMUXC_GPR_GlobalInterruptRequest
-
enum _iomuxc_gpr_saimclk
Values:
-
enumerator kIOMUXC_GPR_SAI1MClk1Sel
-
enumerator kIOMUXC_GPR_SAI1MClk2Sel
-
enumerator kIOMUXC_GPR_SAI1MClk3Sel
-
enumerator kIOMUXC_GPR_SAI2MClk3Sel
-
enumerator kIOMUXC_GPR_SAI3MClk3Sel
-
enumerator kIOMUXC_GPR_SAI1MClk1Sel
-
enum _iomuxc_mqs_pwm_oversample_rate
Values:
-
enumerator kIOMUXC_MqsPwmOverSampleRate32
-
enumerator kIOMUXC_MqsPwmOverSampleRate64
-
enumerator kIOMUXC_MqsPwmOverSampleRate32
-
typedef enum _iomuxc_gpr_mode iomuxc_gpr_mode_t
-
typedef enum _iomuxc_gpr_saimclk iomuxc_gpr_saimclk_t
-
typedef enum _iomuxc_mqs_pwm_oversample_rate iomuxc_mqs_pwm_oversample_rate_t
-
IOMUXC_GPIO_EMC_00_SEMC_DA00
-
IOMUXC_GPIO_EMC_00_FLEXPWM4_PWM0_A
-
IOMUXC_GPIO_EMC_00_LPSPI2_SCK
-
IOMUXC_GPIO_EMC_00_XBAR1_IN02
-
IOMUXC_GPIO_EMC_00_FLEXIO1_D00
-
IOMUXC_GPIO_EMC_00_GPIO4_IO00
-
IOMUXC_GPIO_EMC_01_SEMC_DA01
-
IOMUXC_GPIO_EMC_01_FLEXPWM4_PWM0_B
-
IOMUXC_GPIO_EMC_01_LPSPI2_PCS0
-
IOMUXC_GPIO_EMC_01_XBAR1_IN03
-
IOMUXC_GPIO_EMC_01_FLEXIO1_D01
-
IOMUXC_GPIO_EMC_01_GPIO4_IO01
-
IOMUXC_GPIO_EMC_02_SEMC_DA02
-
IOMUXC_GPIO_EMC_02_FLEXPWM4_PWM1_A
-
IOMUXC_GPIO_EMC_02_LPSPI2_SDO
-
IOMUXC_GPIO_EMC_02_XBAR1_INOUT04
-
IOMUXC_GPIO_EMC_02_FLEXIO1_D02
-
IOMUXC_GPIO_EMC_02_GPIO4_IO02
-
IOMUXC_GPIO_EMC_03_SEMC_DA03
-
IOMUXC_GPIO_EMC_03_FLEXPWM4_PWM1_B
-
IOMUXC_GPIO_EMC_03_LPSPI2_SDI
-
IOMUXC_GPIO_EMC_03_XBAR1_INOUT05
-
IOMUXC_GPIO_EMC_03_FLEXIO1_D03
-
IOMUXC_GPIO_EMC_03_GPIO4_IO03
-
IOMUXC_GPIO_EMC_04_SEMC_DA04
-
IOMUXC_GPIO_EMC_04_FLEXPWM4_PWM2_A
-
IOMUXC_GPIO_EMC_04_SAI2_TX_DATA
-
IOMUXC_GPIO_EMC_04_XBAR1_INOUT06
-
IOMUXC_GPIO_EMC_04_FLEXIO1_D04
-
IOMUXC_GPIO_EMC_04_GPIO4_IO04
-
IOMUXC_GPIO_EMC_05_SEMC_DA05
-
IOMUXC_GPIO_EMC_05_FLEXPWM4_PWM2_B
-
IOMUXC_GPIO_EMC_05_SAI2_TX_SYNC
-
IOMUXC_GPIO_EMC_05_XBAR1_INOUT07
-
IOMUXC_GPIO_EMC_05_FLEXIO1_D05
-
IOMUXC_GPIO_EMC_05_GPIO4_IO05
-
IOMUXC_GPIO_EMC_06_SEMC_DA06
-
IOMUXC_GPIO_EMC_06_FLEXPWM2_PWM0_A
-
IOMUXC_GPIO_EMC_06_SAI2_TX_BCLK
-
IOMUXC_GPIO_EMC_06_XBAR1_INOUT08
-
IOMUXC_GPIO_EMC_06_FLEXIO1_D06
-
IOMUXC_GPIO_EMC_06_GPIO4_IO06
-
IOMUXC_GPIO_EMC_07_SEMC_DA07
-
IOMUXC_GPIO_EMC_07_FLEXPWM2_PWM0_B
-
IOMUXC_GPIO_EMC_07_SAI2_MCLK
-
IOMUXC_GPIO_EMC_07_XBAR1_INOUT09
-
IOMUXC_GPIO_EMC_07_FLEXIO1_D07
-
IOMUXC_GPIO_EMC_07_GPIO4_IO07
-
IOMUXC_GPIO_EMC_08_SEMC_DM00
-
IOMUXC_GPIO_EMC_08_FLEXPWM2_PWM1_A
-
IOMUXC_GPIO_EMC_08_SAI2_RX_DATA
-
IOMUXC_GPIO_EMC_08_XBAR1_INOUT17
-
IOMUXC_GPIO_EMC_08_FLEXIO1_D08
-
IOMUXC_GPIO_EMC_08_GPIO4_IO08
-
IOMUXC_GPIO_EMC_09_SEMC_ADDR00
-
IOMUXC_GPIO_EMC_09_FLEXPWM2_PWM1_B
-
IOMUXC_GPIO_EMC_09_SAI2_RX_SYNC
-
IOMUXC_GPIO_EMC_09_FLEXCAN2_TX
-
IOMUXC_GPIO_EMC_09_FLEXIO1_D09
-
IOMUXC_GPIO_EMC_09_GPIO4_IO09
-
IOMUXC_GPIO_EMC_10_SEMC_ADDR01
-
IOMUXC_GPIO_EMC_10_FLEXPWM2_PWM2_A
-
IOMUXC_GPIO_EMC_10_SAI2_RX_BCLK
-
IOMUXC_GPIO_EMC_10_FLEXCAN2_RX
-
IOMUXC_GPIO_EMC_10_FLEXIO1_D10
-
IOMUXC_GPIO_EMC_10_GPIO4_IO10
-
IOMUXC_GPIO_EMC_11_SEMC_ADDR02
-
IOMUXC_GPIO_EMC_11_FLEXPWM2_PWM2_B
-
IOMUXC_GPIO_EMC_11_LPI2C4_SDA
-
IOMUXC_GPIO_EMC_11_USDHC2_RESET_B
-
IOMUXC_GPIO_EMC_11_FLEXIO1_D11
-
IOMUXC_GPIO_EMC_11_GPIO4_IO11
-
IOMUXC_GPIO_EMC_12_SEMC_ADDR03
-
IOMUXC_GPIO_EMC_12_XBAR1_IN24
-
IOMUXC_GPIO_EMC_12_LPI2C4_SCL
-
IOMUXC_GPIO_EMC_12_USDHC1_WP
-
IOMUXC_GPIO_EMC_12_FLEXPWM1_PWM3_A
-
IOMUXC_GPIO_EMC_12_GPIO4_IO12
-
IOMUXC_GPIO_EMC_13_SEMC_ADDR04
-
IOMUXC_GPIO_EMC_13_XBAR1_IN25
-
IOMUXC_GPIO_EMC_13_LPUART3_TXD
-
IOMUXC_GPIO_EMC_13_MQS_RIGHT
-
IOMUXC_GPIO_EMC_13_FLEXPWM1_PWM3_B
-
IOMUXC_GPIO_EMC_13_GPIO4_IO13
-
IOMUXC_GPIO_EMC_14_SEMC_ADDR05
-
IOMUXC_GPIO_EMC_14_XBAR1_INOUT19
-
IOMUXC_GPIO_EMC_14_LPUART3_RXD
-
IOMUXC_GPIO_EMC_14_MQS_LEFT
-
IOMUXC_GPIO_EMC_14_LPSPI2_PCS1
-
IOMUXC_GPIO_EMC_14_GPIO4_IO14
-
IOMUXC_GPIO_EMC_15_SEMC_ADDR06
-
IOMUXC_GPIO_EMC_15_XBAR1_IN20
-
IOMUXC_GPIO_EMC_15_LPUART3_CTS_B
-
IOMUXC_GPIO_EMC_15_SPDIF_OUT
-
IOMUXC_GPIO_EMC_15_TMR3_TIMER0
-
IOMUXC_GPIO_EMC_15_GPIO4_IO15
-
IOMUXC_GPIO_EMC_16_SEMC_ADDR07
-
IOMUXC_GPIO_EMC_16_XBAR1_IN21
-
IOMUXC_GPIO_EMC_16_LPUART3_RTS_B
-
IOMUXC_GPIO_EMC_16_SPDIF_IN
-
IOMUXC_GPIO_EMC_16_TMR3_TIMER1
-
IOMUXC_GPIO_EMC_16_GPIO4_IO16
-
IOMUXC_GPIO_EMC_17_SEMC_ADDR08
-
IOMUXC_GPIO_EMC_17_FLEXPWM4_PWM3_A
-
IOMUXC_GPIO_EMC_17_LPUART4_CTS_B
-
IOMUXC_GPIO_EMC_17_FLEXCAN1_TX
-
IOMUXC_GPIO_EMC_17_TMR3_TIMER2
-
IOMUXC_GPIO_EMC_17_GPIO4_IO17
-
IOMUXC_GPIO_EMC_18_SEMC_ADDR09
-
IOMUXC_GPIO_EMC_18_FLEXPWM4_PWM3_B
-
IOMUXC_GPIO_EMC_18_LPUART4_RTS_B
-
IOMUXC_GPIO_EMC_18_FLEXCAN1_RX
-
IOMUXC_GPIO_EMC_18_TMR3_TIMER3
-
IOMUXC_GPIO_EMC_18_GPIO4_IO18
-
IOMUXC_GPIO_EMC_18_SNVS_VIO_5_CTL
-
IOMUXC_GPIO_EMC_19_SEMC_ADDR11
-
IOMUXC_GPIO_EMC_19_FLEXPWM2_PWM3_A
-
IOMUXC_GPIO_EMC_19_LPUART4_TXD
-
IOMUXC_GPIO_EMC_19_ENET_RX_DATA01
-
IOMUXC_GPIO_EMC_19_TMR2_TIMER0
-
IOMUXC_GPIO_EMC_19_GPIO4_IO19
-
IOMUXC_GPIO_EMC_19_SNVS_VIO_5
-
IOMUXC_GPIO_EMC_20_SEMC_ADDR12
-
IOMUXC_GPIO_EMC_20_FLEXPWM2_PWM3_B
-
IOMUXC_GPIO_EMC_20_LPUART4_RXD
-
IOMUXC_GPIO_EMC_20_ENET_RX_DATA00
-
IOMUXC_GPIO_EMC_20_TMR2_TIMER1
-
IOMUXC_GPIO_EMC_20_GPIO4_IO20
-
IOMUXC_GPIO_EMC_21_SEMC_BA0
-
IOMUXC_GPIO_EMC_21_FLEXPWM3_PWM3_A
-
IOMUXC_GPIO_EMC_21_LPI2C3_SDA
-
IOMUXC_GPIO_EMC_21_ENET_TX_DATA01
-
IOMUXC_GPIO_EMC_21_TMR2_TIMER2
-
IOMUXC_GPIO_EMC_21_GPIO4_IO21
-
IOMUXC_GPIO_EMC_22_SEMC_BA1
-
IOMUXC_GPIO_EMC_22_FLEXPWM3_PWM3_B
-
IOMUXC_GPIO_EMC_22_LPI2C3_SCL
-
IOMUXC_GPIO_EMC_22_ENET_TX_DATA00
-
IOMUXC_GPIO_EMC_22_TMR2_TIMER3
-
IOMUXC_GPIO_EMC_22_GPIO4_IO22
-
IOMUXC_GPIO_EMC_23_SEMC_ADDR10
-
IOMUXC_GPIO_EMC_23_FLEXPWM1_PWM0_A
-
IOMUXC_GPIO_EMC_23_LPUART5_TXD
-
IOMUXC_GPIO_EMC_23_ENET_RX_EN
-
IOMUXC_GPIO_EMC_23_GPT1_CAPTURE2
-
IOMUXC_GPIO_EMC_23_GPIO4_IO23
-
IOMUXC_GPIO_EMC_24_SEMC_CAS
-
IOMUXC_GPIO_EMC_24_FLEXPWM1_PWM0_B
-
IOMUXC_GPIO_EMC_24_LPUART5_RXD
-
IOMUXC_GPIO_EMC_24_ENET_TX_EN
-
IOMUXC_GPIO_EMC_24_GPT1_CAPTURE1
-
IOMUXC_GPIO_EMC_24_GPIO4_IO24
-
IOMUXC_GPIO_EMC_25_SEMC_RAS
-
IOMUXC_GPIO_EMC_25_FLEXPWM1_PWM1_A
-
IOMUXC_GPIO_EMC_25_LPUART6_TXD
-
IOMUXC_GPIO_EMC_25_ENET_TX_CLK
-
IOMUXC_GPIO_EMC_25_ENET_REF_CLK
-
IOMUXC_GPIO_EMC_25_GPIO4_IO25
-
IOMUXC_GPIO_EMC_26_SEMC_CLK
-
IOMUXC_GPIO_EMC_26_FLEXPWM1_PWM1_B
-
IOMUXC_GPIO_EMC_26_LPUART6_RXD
-
IOMUXC_GPIO_EMC_26_ENET_RX_ER
-
IOMUXC_GPIO_EMC_26_FLEXIO1_D12
-
IOMUXC_GPIO_EMC_26_GPIO4_IO26
-
IOMUXC_GPIO_EMC_27_SEMC_CKE
-
IOMUXC_GPIO_EMC_27_FLEXPWM1_PWM2_A
-
IOMUXC_GPIO_EMC_27_LPUART5_RTS_B
-
IOMUXC_GPIO_EMC_27_LPSPI1_SCK
-
IOMUXC_GPIO_EMC_27_FLEXIO1_D13
-
IOMUXC_GPIO_EMC_27_GPIO4_IO27
-
IOMUXC_GPIO_EMC_28_SEMC_WE
-
IOMUXC_GPIO_EMC_28_FLEXPWM1_PWM2_B
-
IOMUXC_GPIO_EMC_28_LPUART5_CTS_B
-
IOMUXC_GPIO_EMC_28_LPSPI1_SDO
-
IOMUXC_GPIO_EMC_28_FLEXIO1_D14
-
IOMUXC_GPIO_EMC_28_GPIO4_IO28
-
IOMUXC_GPIO_EMC_29_SEMC_CS0
-
IOMUXC_GPIO_EMC_29_FLEXPWM3_PWM0_A
-
IOMUXC_GPIO_EMC_29_LPUART6_RTS_B
-
IOMUXC_GPIO_EMC_29_LPSPI1_SDI
-
IOMUXC_GPIO_EMC_29_FLEXIO1_D15
-
IOMUXC_GPIO_EMC_29_GPIO4_IO29
-
IOMUXC_GPIO_EMC_30_SEMC_DA08
-
IOMUXC_GPIO_EMC_30_FLEXPWM3_PWM0_B
-
IOMUXC_GPIO_EMC_30_LPUART6_CTS_B
-
IOMUXC_GPIO_EMC_30_LPSPI1_PCS0
-
IOMUXC_GPIO_EMC_30_CSI_DATA23
-
IOMUXC_GPIO_EMC_30_GPIO4_IO30
-
IOMUXC_GPIO_EMC_31_SEMC_DA09
-
IOMUXC_GPIO_EMC_31_FLEXPWM3_PWM1_A
-
IOMUXC_GPIO_EMC_31_LPUART7_TXD
-
IOMUXC_GPIO_EMC_31_LPSPI1_PCS1
-
IOMUXC_GPIO_EMC_31_CSI_DATA22
-
IOMUXC_GPIO_EMC_31_GPIO4_IO31
-
IOMUXC_GPIO_EMC_32_SEMC_DA10
-
IOMUXC_GPIO_EMC_32_FLEXPWM3_PWM1_B
-
IOMUXC_GPIO_EMC_32_LPUART7_RXD
-
IOMUXC_GPIO_EMC_32_CCM_PMIC_READY
-
IOMUXC_GPIO_EMC_32_CSI_DATA21
-
IOMUXC_GPIO_EMC_32_GPIO3_IO18
-
IOMUXC_GPIO_EMC_33_SEMC_DA11
-
IOMUXC_GPIO_EMC_33_FLEXPWM3_PWM2_A
-
IOMUXC_GPIO_EMC_33_USDHC1_RESET_B
-
IOMUXC_GPIO_EMC_33_SAI3_RX_DATA
-
IOMUXC_GPIO_EMC_33_CSI_DATA20
-
IOMUXC_GPIO_EMC_33_GPIO3_IO19
-
IOMUXC_GPIO_EMC_34_SEMC_DA12
-
IOMUXC_GPIO_EMC_34_FLEXPWM3_PWM2_B
-
IOMUXC_GPIO_EMC_34_USDHC1_VSELECT
-
IOMUXC_GPIO_EMC_34_SAI3_RX_SYNC
-
IOMUXC_GPIO_EMC_34_CSI_DATA19
-
IOMUXC_GPIO_EMC_34_GPIO3_IO20
-
IOMUXC_GPIO_EMC_35_SEMC_DA13
-
IOMUXC_GPIO_EMC_35_XBAR1_INOUT18
-
IOMUXC_GPIO_EMC_35_GPT1_COMPARE1
-
IOMUXC_GPIO_EMC_35_SAI3_RX_BCLK
-
IOMUXC_GPIO_EMC_35_CSI_DATA18
-
IOMUXC_GPIO_EMC_35_GPIO3_IO21
-
IOMUXC_GPIO_EMC_35_USDHC1_CD_B
-
IOMUXC_GPIO_EMC_36_SEMC_DA14
-
IOMUXC_GPIO_EMC_36_XBAR1_IN22
-
IOMUXC_GPIO_EMC_36_GPT1_COMPARE2
-
IOMUXC_GPIO_EMC_36_SAI3_TX_DATA
-
IOMUXC_GPIO_EMC_36_CSI_DATA17
-
IOMUXC_GPIO_EMC_36_GPIO3_IO22
-
IOMUXC_GPIO_EMC_36_USDHC1_WP
-
IOMUXC_GPIO_EMC_37_SEMC_DA15
-
IOMUXC_GPIO_EMC_37_XBAR1_IN23
-
IOMUXC_GPIO_EMC_37_GPT1_COMPARE3
-
IOMUXC_GPIO_EMC_37_SAI3_MCLK
-
IOMUXC_GPIO_EMC_37_CSI_DATA16
-
IOMUXC_GPIO_EMC_37_GPIO3_IO23
-
IOMUXC_GPIO_EMC_37_USDHC2_WP
-
IOMUXC_GPIO_EMC_38_SEMC_DM01
-
IOMUXC_GPIO_EMC_38_FLEXPWM1_PWM3_A
-
IOMUXC_GPIO_EMC_38_LPUART8_TXD
-
IOMUXC_GPIO_EMC_38_SAI3_TX_BCLK
-
IOMUXC_GPIO_EMC_38_CSI_FIELD
-
IOMUXC_GPIO_EMC_38_GPIO3_IO24
-
IOMUXC_GPIO_EMC_38_USDHC2_VSELECT
-
IOMUXC_GPIO_EMC_39_SEMC_DQS
-
IOMUXC_GPIO_EMC_39_FLEXPWM1_PWM3_B
-
IOMUXC_GPIO_EMC_39_LPUART8_RXD
-
IOMUXC_GPIO_EMC_39_SAI3_TX_SYNC
-
IOMUXC_GPIO_EMC_39_WDOG1_B
-
IOMUXC_GPIO_EMC_39_GPIO3_IO25
-
IOMUXC_GPIO_EMC_39_USDHC2_CD_B
-
IOMUXC_GPIO_EMC_40_SEMC_RDY
-
IOMUXC_GPIO_EMC_40_GPT2_CAPTURE2
-
IOMUXC_GPIO_EMC_40_LPSPI1_PCS2
-
IOMUXC_GPIO_EMC_40_USB_OTG2_OC
-
IOMUXC_GPIO_EMC_40_ENET_MDC
-
IOMUXC_GPIO_EMC_40_GPIO3_IO26
-
IOMUXC_GPIO_EMC_40_USDHC2_RESET_B
-
IOMUXC_GPIO_EMC_41_SEMC_CSX0
-
IOMUXC_GPIO_EMC_41_GPT2_CAPTURE1
-
IOMUXC_GPIO_EMC_41_LPSPI1_PCS3
-
IOMUXC_GPIO_EMC_41_USB_OTG2_PWR
-
IOMUXC_GPIO_EMC_41_ENET_MDIO
-
IOMUXC_GPIO_EMC_41_GPIO3_IO27
-
IOMUXC_GPIO_EMC_41_USDHC1_VSELECT
-
IOMUXC_GPIO_AD_B0_00_FLEXPWM2_PWM3_A
-
IOMUXC_GPIO_AD_B0_00_XBAR1_INOUT14
-
IOMUXC_GPIO_AD_B0_00_REF_CLK_32K
-
IOMUXC_GPIO_AD_B0_00_USB_OTG2_ID
-
IOMUXC_GPIO_AD_B0_00_LPI2C1_SCLS
-
IOMUXC_GPIO_AD_B0_00_GPIO1_IO00
-
IOMUXC_GPIO_AD_B0_00_USDHC1_RESET_B
-
IOMUXC_GPIO_AD_B0_00_LPSPI3_SCK
-
IOMUXC_GPIO_AD_B0_01_FLEXPWM2_PWM3_B
-
IOMUXC_GPIO_AD_B0_01_XBAR1_INOUT15
-
IOMUXC_GPIO_AD_B0_01_REF_CLK_24M
-
IOMUXC_GPIO_AD_B0_01_USB_OTG1_ID
-
IOMUXC_GPIO_AD_B0_01_LPI2C1_SDAS
-
IOMUXC_GPIO_AD_B0_01_GPIO1_IO01
-
IOMUXC_GPIO_AD_B0_01_EWM_OUT_B
-
IOMUXC_GPIO_AD_B0_01_LPSPI3_SDO
-
IOMUXC_GPIO_AD_B0_02_FLEXCAN2_TX
-
IOMUXC_GPIO_AD_B0_02_XBAR1_INOUT16
-
IOMUXC_GPIO_AD_B0_02_LPUART6_TXD
-
IOMUXC_GPIO_AD_B0_02_USB_OTG1_PWR
-
IOMUXC_GPIO_AD_B0_02_FLEXPWM1_PWM0_X
-
IOMUXC_GPIO_AD_B0_02_GPIO1_IO02
-
IOMUXC_GPIO_AD_B0_02_LPI2C1_HREQ
-
IOMUXC_GPIO_AD_B0_02_LPSPI3_SDI
-
IOMUXC_GPIO_AD_B0_03_FLEXCAN2_RX
-
IOMUXC_GPIO_AD_B0_03_XBAR1_INOUT17
-
IOMUXC_GPIO_AD_B0_03_LPUART6_RXD
-
IOMUXC_GPIO_AD_B0_03_USB_OTG1_OC
-
IOMUXC_GPIO_AD_B0_03_FLEXPWM1_PWM1_X
-
IOMUXC_GPIO_AD_B0_03_GPIO1_IO03
-
IOMUXC_GPIO_AD_B0_03_REF_CLK_24M
-
IOMUXC_GPIO_AD_B0_03_LPSPI3_PCS0
-
IOMUXC_GPIO_AD_B0_04_SRC_BOOT_MODE00
-
IOMUXC_GPIO_AD_B0_04_MQS_RIGHT
-
IOMUXC_GPIO_AD_B0_04_ENET_TX_DATA03
-
IOMUXC_GPIO_AD_B0_04_SAI2_TX_SYNC
-
IOMUXC_GPIO_AD_B0_04_CSI_DATA09
-
IOMUXC_GPIO_AD_B0_04_GPIO1_IO04
-
IOMUXC_GPIO_AD_B0_04_PIT_TRIGGER00
-
IOMUXC_GPIO_AD_B0_04_LPSPI3_PCS1
-
IOMUXC_GPIO_AD_B0_05_SRC_BOOT_MODE01
-
IOMUXC_GPIO_AD_B0_05_MQS_LEFT
-
IOMUXC_GPIO_AD_B0_05_ENET_TX_DATA02
-
IOMUXC_GPIO_AD_B0_05_SAI2_TX_BCLK
-
IOMUXC_GPIO_AD_B0_05_CSI_DATA08
-
IOMUXC_GPIO_AD_B0_05_GPIO1_IO05
-
IOMUXC_GPIO_AD_B0_05_XBAR1_INOUT17
-
IOMUXC_GPIO_AD_B0_05_LPSPI3_PCS2
-
IOMUXC_GPIO_AD_B0_06_JTAG_TMS
-
IOMUXC_GPIO_AD_B0_06_GPT2_COMPARE1
-
IOMUXC_GPIO_AD_B0_06_ENET_RX_CLK
-
IOMUXC_GPIO_AD_B0_06_SAI2_RX_BCLK
-
IOMUXC_GPIO_AD_B0_06_CSI_DATA07
-
IOMUXC_GPIO_AD_B0_06_GPIO1_IO06
-
IOMUXC_GPIO_AD_B0_06_XBAR1_INOUT18
-
IOMUXC_GPIO_AD_B0_06_LPSPI3_PCS3
-
IOMUXC_GPIO_AD_B0_07_JTAG_TCK
-
IOMUXC_GPIO_AD_B0_07_GPT2_COMPARE2
-
IOMUXC_GPIO_AD_B0_07_ENET_TX_ER
-
IOMUXC_GPIO_AD_B0_07_SAI2_RX_SYNC
-
IOMUXC_GPIO_AD_B0_07_CSI_DATA06
-
IOMUXC_GPIO_AD_B0_07_GPIO1_IO07
-
IOMUXC_GPIO_AD_B0_07_XBAR1_INOUT19
-
IOMUXC_GPIO_AD_B0_07_ENET_1588_EVENT3_OUT
-
IOMUXC_GPIO_AD_B0_08_JTAG_MOD
-
IOMUXC_GPIO_AD_B0_08_GPT2_COMPARE3
-
IOMUXC_GPIO_AD_B0_08_ENET_RX_DATA03
-
IOMUXC_GPIO_AD_B0_08_SAI2_RX_DATA
-
IOMUXC_GPIO_AD_B0_08_CSI_DATA05
-
IOMUXC_GPIO_AD_B0_08_GPIO1_IO08
-
IOMUXC_GPIO_AD_B0_08_XBAR1_IN20
-
IOMUXC_GPIO_AD_B0_08_ENET_1588_EVENT3_IN
-
IOMUXC_GPIO_AD_B0_09_JTAG_TDI
-
IOMUXC_GPIO_AD_B0_09_FLEXPWM2_PWM3_A
-
IOMUXC_GPIO_AD_B0_09_ENET_RX_DATA02
-
IOMUXC_GPIO_AD_B0_09_SAI2_TX_DATA
-
IOMUXC_GPIO_AD_B0_09_CSI_DATA04
-
IOMUXC_GPIO_AD_B0_09_GPIO1_IO09
-
IOMUXC_GPIO_AD_B0_09_XBAR1_IN21
-
IOMUXC_GPIO_AD_B0_09_GPT2_CLK
-
IOMUXC_GPIO_AD_B0_10_JTAG_TDO
-
IOMUXC_GPIO_AD_B0_10_FLEXPWM1_PWM3_A
-
IOMUXC_GPIO_AD_B0_10_ENET_CRS
-
IOMUXC_GPIO_AD_B0_10_SAI2_MCLK
-
IOMUXC_GPIO_AD_B0_10_CSI_DATA03
-
IOMUXC_GPIO_AD_B0_10_GPIO1_IO10
-
IOMUXC_GPIO_AD_B0_10_XBAR1_IN22
-
IOMUXC_GPIO_AD_B0_10_ENET_1588_EVENT0_OUT
-
IOMUXC_GPIO_AD_B0_11_JTAG_TRSTB
-
IOMUXC_GPIO_AD_B0_11_FLEXPWM1_PWM3_B
-
IOMUXC_GPIO_AD_B0_11_ENET_COL
-
IOMUXC_GPIO_AD_B0_11_WDOG1_B
-
IOMUXC_GPIO_AD_B0_11_CSI_DATA02
-
IOMUXC_GPIO_AD_B0_11_GPIO1_IO11
-
IOMUXC_GPIO_AD_B0_11_XBAR1_IN23
-
IOMUXC_GPIO_AD_B0_11_ENET_1588_EVENT0_IN
-
IOMUXC_GPIO_AD_B0_12_LPI2C4_SCL
-
IOMUXC_GPIO_AD_B0_12_CCM_PMIC_READY
-
IOMUXC_GPIO_AD_B0_12_LPUART1_TXD
-
IOMUXC_GPIO_AD_B0_12_WDOG2_B
-
IOMUXC_GPIO_AD_B0_12_FLEXPWM1_PWM2_X
-
IOMUXC_GPIO_AD_B0_12_GPIO1_IO12
-
IOMUXC_GPIO_AD_B0_12_ENET_1588_EVENT1_OUT
-
IOMUXC_GPIO_AD_B0_12_NMI
-
IOMUXC_GPIO_AD_B0_13_LPI2C4_SDA
-
IOMUXC_GPIO_AD_B0_13_GPT1_CLK
-
IOMUXC_GPIO_AD_B0_13_LPUART1_RXD
-
IOMUXC_GPIO_AD_B0_13_EWM_OUT_B
-
IOMUXC_GPIO_AD_B0_13_FLEXPWM1_PWM3_X
-
IOMUXC_GPIO_AD_B0_13_GPIO1_IO13
-
IOMUXC_GPIO_AD_B0_13_ENET_1588_EVENT1_IN
-
IOMUXC_GPIO_AD_B0_13_REF_CLK_24M
-
IOMUXC_GPIO_AD_B0_14_USB_OTG2_OC
-
IOMUXC_GPIO_AD_B0_14_XBAR1_IN24
-
IOMUXC_GPIO_AD_B0_14_LPUART1_CTS_B
-
IOMUXC_GPIO_AD_B0_14_ENET_1588_EVENT0_OUT
-
IOMUXC_GPIO_AD_B0_14_CSI_VSYNC
-
IOMUXC_GPIO_AD_B0_14_GPIO1_IO14
-
IOMUXC_GPIO_AD_B0_14_FLEXCAN2_TX
-
IOMUXC_GPIO_AD_B0_15_USB_OTG2_PWR
-
IOMUXC_GPIO_AD_B0_15_XBAR1_IN25
-
IOMUXC_GPIO_AD_B0_15_LPUART1_RTS_B
-
IOMUXC_GPIO_AD_B0_15_ENET_1588_EVENT0_IN
-
IOMUXC_GPIO_AD_B0_15_CSI_HSYNC
-
IOMUXC_GPIO_AD_B0_15_GPIO1_IO15
-
IOMUXC_GPIO_AD_B0_15_FLEXCAN2_RX
-
IOMUXC_GPIO_AD_B0_15_WDOG1_WDOG_RST_B_DEB
-
IOMUXC_GPIO_AD_B1_00_USB_OTG2_ID
-
IOMUXC_GPIO_AD_B1_00_TMR3_TIMER0
-
IOMUXC_GPIO_AD_B1_00_LPUART2_CTS_B
-
IOMUXC_GPIO_AD_B1_00_LPI2C1_SCL
-
IOMUXC_GPIO_AD_B1_00_WDOG1_B
-
IOMUXC_GPIO_AD_B1_00_GPIO1_IO16
-
IOMUXC_GPIO_AD_B1_00_USDHC1_WP
-
IOMUXC_GPIO_AD_B1_00_KPP_ROW07
-
IOMUXC_GPIO_AD_B1_01_USB_OTG1_PWR
-
IOMUXC_GPIO_AD_B1_01_TMR3_TIMER1
-
IOMUXC_GPIO_AD_B1_01_LPUART2_RTS_B
-
IOMUXC_GPIO_AD_B1_01_LPI2C1_SDA
-
IOMUXC_GPIO_AD_B1_01_CCM_PMIC_READY
-
IOMUXC_GPIO_AD_B1_01_GPIO1_IO17
-
IOMUXC_GPIO_AD_B1_01_USDHC1_VSELECT
-
IOMUXC_GPIO_AD_B1_01_KPP_COL07
-
IOMUXC_GPIO_AD_B1_02_USB_OTG1_ID
-
IOMUXC_GPIO_AD_B1_02_TMR3_TIMER2
-
IOMUXC_GPIO_AD_B1_02_LPUART2_TXD
-
IOMUXC_GPIO_AD_B1_02_SPDIF_OUT
-
IOMUXC_GPIO_AD_B1_02_ENET_1588_EVENT2_OUT
-
IOMUXC_GPIO_AD_B1_02_GPIO1_IO18
-
IOMUXC_GPIO_AD_B1_02_USDHC1_CD_B
-
IOMUXC_GPIO_AD_B1_02_KPP_ROW06
-
IOMUXC_GPIO_AD_B1_03_USB_OTG1_OC
-
IOMUXC_GPIO_AD_B1_03_TMR3_TIMER3
-
IOMUXC_GPIO_AD_B1_03_LPUART2_RXD
-
IOMUXC_GPIO_AD_B1_03_SPDIF_IN
-
IOMUXC_GPIO_AD_B1_03_ENET_1588_EVENT2_IN
-
IOMUXC_GPIO_AD_B1_03_GPIO1_IO19
-
IOMUXC_GPIO_AD_B1_03_USDHC2_CD_B
-
IOMUXC_GPIO_AD_B1_03_KPP_COL06
-
IOMUXC_GPIO_AD_B1_04_FLEXSPI_B_DATA3
-
IOMUXC_GPIO_AD_B1_04_ENET_MDC
-
IOMUXC_GPIO_AD_B1_04_LPUART3_CTS_B
-
IOMUXC_GPIO_AD_B1_04_SPDIF_SR_CLK
-
IOMUXC_GPIO_AD_B1_04_CSI_PIXCLK
-
IOMUXC_GPIO_AD_B1_04_GPIO1_IO20
-
IOMUXC_GPIO_AD_B1_04_USDHC2_DATA0
-
IOMUXC_GPIO_AD_B1_04_KPP_ROW05
-
IOMUXC_GPIO_AD_B1_05_FLEXSPI_B_DATA2
-
IOMUXC_GPIO_AD_B1_05_ENET_MDIO
-
IOMUXC_GPIO_AD_B1_05_LPUART3_RTS_B
-
IOMUXC_GPIO_AD_B1_05_SPDIF_OUT
-
IOMUXC_GPIO_AD_B1_05_CSI_MCLK
-
IOMUXC_GPIO_AD_B1_05_GPIO1_IO21
-
IOMUXC_GPIO_AD_B1_05_USDHC2_DATA1
-
IOMUXC_GPIO_AD_B1_05_KPP_COL05
-
IOMUXC_GPIO_AD_B1_06_FLEXSPI_B_DATA1
-
IOMUXC_GPIO_AD_B1_06_LPI2C3_SDA
-
IOMUXC_GPIO_AD_B1_06_LPUART3_TXD
-
IOMUXC_GPIO_AD_B1_06_SPDIF_LOCK
-
IOMUXC_GPIO_AD_B1_06_CSI_VSYNC
-
IOMUXC_GPIO_AD_B1_06_GPIO1_IO22
-
IOMUXC_GPIO_AD_B1_06_USDHC2_DATA2
-
IOMUXC_GPIO_AD_B1_06_KPP_ROW04
-
IOMUXC_GPIO_AD_B1_07_FLEXSPI_B_DATA0
-
IOMUXC_GPIO_AD_B1_07_LPI2C3_SCL
-
IOMUXC_GPIO_AD_B1_07_LPUART3_RXD
-
IOMUXC_GPIO_AD_B1_07_SPDIF_EXT_CLK
-
IOMUXC_GPIO_AD_B1_07_CSI_HSYNC
-
IOMUXC_GPIO_AD_B1_07_GPIO1_IO23
-
IOMUXC_GPIO_AD_B1_07_USDHC2_DATA3
-
IOMUXC_GPIO_AD_B1_07_KPP_COL04
-
IOMUXC_GPIO_AD_B1_08_FLEXSPI_A_SS1_B
-
IOMUXC_GPIO_AD_B1_08_FLEXPWM4_PWM0_A
-
IOMUXC_GPIO_AD_B1_08_FLEXCAN1_TX
-
IOMUXC_GPIO_AD_B1_08_CCM_PMIC_READY
-
IOMUXC_GPIO_AD_B1_08_CSI_DATA09
-
IOMUXC_GPIO_AD_B1_08_GPIO1_IO24
-
IOMUXC_GPIO_AD_B1_08_USDHC2_CMD
-
IOMUXC_GPIO_AD_B1_08_KPP_ROW03
-
IOMUXC_GPIO_AD_B1_09_FLEXSPI_A_DQS
-
IOMUXC_GPIO_AD_B1_09_FLEXPWM4_PWM1_A
-
IOMUXC_GPIO_AD_B1_09_FLEXCAN1_RX
-
IOMUXC_GPIO_AD_B1_09_SAI1_MCLK
-
IOMUXC_GPIO_AD_B1_09_CSI_DATA08
-
IOMUXC_GPIO_AD_B1_09_GPIO1_IO25
-
IOMUXC_GPIO_AD_B1_09_USDHC2_CLK
-
IOMUXC_GPIO_AD_B1_09_KPP_COL03
-
IOMUXC_GPIO_AD_B1_10_FLEXSPI_A_DATA3
-
IOMUXC_GPIO_AD_B1_10_WDOG1_B
-
IOMUXC_GPIO_AD_B1_10_LPUART8_TXD
-
IOMUXC_GPIO_AD_B1_10_SAI1_RX_SYNC
-
IOMUXC_GPIO_AD_B1_10_CSI_DATA07
-
IOMUXC_GPIO_AD_B1_10_GPIO1_IO26
-
IOMUXC_GPIO_AD_B1_10_USDHC2_WP
-
IOMUXC_GPIO_AD_B1_10_KPP_ROW02
-
IOMUXC_GPIO_AD_B1_11_FLEXSPI_A_DATA2
-
IOMUXC_GPIO_AD_B1_11_EWM_OUT_B
-
IOMUXC_GPIO_AD_B1_11_LPUART8_RXD
-
IOMUXC_GPIO_AD_B1_11_SAI1_RX_BCLK
-
IOMUXC_GPIO_AD_B1_11_CSI_DATA06
-
IOMUXC_GPIO_AD_B1_11_GPIO1_IO27
-
IOMUXC_GPIO_AD_B1_11_USDHC2_RESET_B
-
IOMUXC_GPIO_AD_B1_11_KPP_COL02
-
IOMUXC_GPIO_AD_B1_12_FLEXSPI_A_DATA1
-
IOMUXC_GPIO_AD_B1_12_ACMP1_OUT
-
IOMUXC_GPIO_AD_B1_12_LPSPI3_PCS0
-
IOMUXC_GPIO_AD_B1_12_SAI1_RX_DATA00
-
IOMUXC_GPIO_AD_B1_12_CSI_DATA05
-
IOMUXC_GPIO_AD_B1_12_GPIO1_IO28
-
IOMUXC_GPIO_AD_B1_12_USDHC2_DATA4
-
IOMUXC_GPIO_AD_B1_12_KPP_ROW01
-
IOMUXC_GPIO_AD_B1_13_FLEXSPI_A_DATA00
-
IOMUXC_GPIO_AD_B1_13_ACMP2_OUT
-
IOMUXC_GPIO_AD_B1_13_LPSPI3_SDI
-
IOMUXC_GPIO_AD_B1_13_SAI1_TX_DATA00
-
IOMUXC_GPIO_AD_B1_13_CSI_DATA04
-
IOMUXC_GPIO_AD_B1_13_GPIO1_IO29
-
IOMUXC_GPIO_AD_B1_13_USDHC2_DATA5
-
IOMUXC_GPIO_AD_B1_13_KPP_COL01
-
IOMUXC_GPIO_AD_B1_14_FLEXSPI_A_SCLK
-
IOMUXC_GPIO_AD_B1_14_ACMP3_OUT
-
IOMUXC_GPIO_AD_B1_14_LPSPI3_SDO
-
IOMUXC_GPIO_AD_B1_14_SAI1_TX_BCLK
-
IOMUXC_GPIO_AD_B1_14_CSI_DATA03
-
IOMUXC_GPIO_AD_B1_14_GPIO1_IO30
-
IOMUXC_GPIO_AD_B1_14_USDHC2_DATA6
-
IOMUXC_GPIO_AD_B1_14_KPP_ROW00
-
IOMUXC_GPIO_AD_B1_15_FLEXSPI_A_SS0_B
-
IOMUXC_GPIO_AD_B1_15_ACMP4_OUT
-
IOMUXC_GPIO_AD_B1_15_LPSPI3_SCK
-
IOMUXC_GPIO_AD_B1_15_SAI1_TX_SYNC
-
IOMUXC_GPIO_AD_B1_15_CSI_DATA02
-
IOMUXC_GPIO_AD_B1_15_GPIO1_IO31
-
IOMUXC_GPIO_AD_B1_15_USDHC2_DATA7
-
IOMUXC_GPIO_AD_B1_15_KPP_COL00
-
IOMUXC_GPIO_B0_00_LCD_CLK
-
IOMUXC_GPIO_B0_00_TMR1_TIMER0
-
IOMUXC_GPIO_B0_00_MQS_RIGHT
-
IOMUXC_GPIO_B0_00_LPSPI4_PCS0
-
IOMUXC_GPIO_B0_00_FLEXIO2_D00
-
IOMUXC_GPIO_B0_00_GPIO2_IO00
-
IOMUXC_GPIO_B0_00_SEMC_CSX1
-
IOMUXC_GPIO_B0_01_LCD_ENABLE
-
IOMUXC_GPIO_B0_01_TMR1_TIMER1
-
IOMUXC_GPIO_B0_01_MQS_LEFT
-
IOMUXC_GPIO_B0_01_LPSPI4_SDI
-
IOMUXC_GPIO_B0_01_FLEXIO2_D01
-
IOMUXC_GPIO_B0_01_GPIO2_IO01
-
IOMUXC_GPIO_B0_01_SEMC_CSX2
-
IOMUXC_GPIO_B0_02_LCD_HSYNC
-
IOMUXC_GPIO_B0_02_TMR1_TIMER2
-
IOMUXC_GPIO_B0_02_FLEXCAN1_TX
-
IOMUXC_GPIO_B0_02_LPSPI4_SDO
-
IOMUXC_GPIO_B0_02_FLEXIO2_D02
-
IOMUXC_GPIO_B0_02_GPIO2_IO02
-
IOMUXC_GPIO_B0_02_SEMC_CSX3
-
IOMUXC_GPIO_B0_03_LCD_VSYNC
-
IOMUXC_GPIO_B0_03_TMR2_TIMER0
-
IOMUXC_GPIO_B0_03_FLEXCAN1_RX
-
IOMUXC_GPIO_B0_03_LPSPI4_SCK
-
IOMUXC_GPIO_B0_03_FLEXIO2_D03
-
IOMUXC_GPIO_B0_03_GPIO2_IO03
-
IOMUXC_GPIO_B0_03_WDOG2_RESET_B_DEB
-
IOMUXC_GPIO_B0_04_LCD_DATA00
-
IOMUXC_GPIO_B0_04_TMR2_TIMER1
-
IOMUXC_GPIO_B0_04_LPI2C2_SCL
-
IOMUXC_GPIO_B0_04_ARM_TRACE00
-
IOMUXC_GPIO_B0_04_FLEXIO2_D04
-
IOMUXC_GPIO_B0_04_GPIO2_IO04
-
IOMUXC_GPIO_B0_04_SRC_BT_CFG00
-
IOMUXC_GPIO_B0_05_LCD_DATA01
-
IOMUXC_GPIO_B0_05_TMR2_TIMER2
-
IOMUXC_GPIO_B0_05_LPI2C2_SDA
-
IOMUXC_GPIO_B0_05_ARM_TRACE01
-
IOMUXC_GPIO_B0_05_FLEXIO2_D05
-
IOMUXC_GPIO_B0_05_GPIO2_IO05
-
IOMUXC_GPIO_B0_05_SRC_BT_CFG01
-
IOMUXC_GPIO_B0_06_LCD_DATA02
-
IOMUXC_GPIO_B0_06_TMR3_TIMER0
-
IOMUXC_GPIO_B0_06_FLEXPWM2_PWM0_A
-
IOMUXC_GPIO_B0_06_ARM_TRACE02
-
IOMUXC_GPIO_B0_06_FLEXIO2_D06
-
IOMUXC_GPIO_B0_06_GPIO2_IO06
-
IOMUXC_GPIO_B0_06_SRC_BT_CFG02
-
IOMUXC_GPIO_B0_07_LCD_DATA03
-
IOMUXC_GPIO_B0_07_TMR3_TIMER1
-
IOMUXC_GPIO_B0_07_FLEXPWM2_PWM0_B
-
IOMUXC_GPIO_B0_07_ARM_TRACE03
-
IOMUXC_GPIO_B0_07_FLEXIO2_D07
-
IOMUXC_GPIO_B0_07_GPIO2_IO07
-
IOMUXC_GPIO_B0_07_SRC_BT_CFG03
-
IOMUXC_GPIO_B0_08_LCD_DATA04
-
IOMUXC_GPIO_B0_08_TMR3_TIMER2
-
IOMUXC_GPIO_B0_08_FLEXPWM2_PWM1_A
-
IOMUXC_GPIO_B0_08_LPUART3_TXD
-
IOMUXC_GPIO_B0_08_FLEXIO2_D08
-
IOMUXC_GPIO_B0_08_GPIO2_IO08
-
IOMUXC_GPIO_B0_08_SRC_BT_CFG04
-
IOMUXC_GPIO_B0_09_LCD_DATA05
-
IOMUXC_GPIO_B0_09_TMR4_TIMER0
-
IOMUXC_GPIO_B0_09_FLEXPWM2_PWM1_B
-
IOMUXC_GPIO_B0_09_LPUART3_RXD
-
IOMUXC_GPIO_B0_09_FLEXIO2_D09
-
IOMUXC_GPIO_B0_09_GPIO2_IO09
-
IOMUXC_GPIO_B0_09_SRC_BT_CFG05
-
IOMUXC_GPIO_B0_10_LCD_DATA06
-
IOMUXC_GPIO_B0_10_TMR4_TIMER1
-
IOMUXC_GPIO_B0_10_FLEXPWM2_PWM2_A
-
IOMUXC_GPIO_B0_10_SAI1_TX_DATA03
-
IOMUXC_GPIO_B0_10_FLEXIO2_D10
-
IOMUXC_GPIO_B0_10_GPIO2_IO10
-
IOMUXC_GPIO_B0_10_SRC_BT_CFG06
-
IOMUXC_GPIO_B0_11_LCD_DATA07
-
IOMUXC_GPIO_B0_11_TMR4_TIMER2
-
IOMUXC_GPIO_B0_11_FLEXPWM2_PWM2_B
-
IOMUXC_GPIO_B0_11_SAI1_TX_DATA02
-
IOMUXC_GPIO_B0_11_FLEXIO2_D11
-
IOMUXC_GPIO_B0_11_GPIO2_IO11
-
IOMUXC_GPIO_B0_11_SRC_BT_CFG07
-
IOMUXC_GPIO_B0_12_LCD_DATA08
-
IOMUXC_GPIO_B0_12_XBAR1_INOUT10
-
IOMUXC_GPIO_B0_12_ARM_TRACE_CLK
-
IOMUXC_GPIO_B0_12_SAI1_TX_DATA01
-
IOMUXC_GPIO_B0_12_FLEXIO2_D12
-
IOMUXC_GPIO_B0_12_GPIO2_IO12
-
IOMUXC_GPIO_B0_12_SRC_BT_CFG08
-
IOMUXC_GPIO_B0_13_LCD_DATA09
-
IOMUXC_GPIO_B0_13_XBAR1_INOUT11
-
IOMUXC_GPIO_B0_13_ARM_TRACE_SWO
-
IOMUXC_GPIO_B0_13_SAI1_MCLK
-
IOMUXC_GPIO_B0_13_FLEXIO2_D13
-
IOMUXC_GPIO_B0_13_GPIO2_IO13
-
IOMUXC_GPIO_B0_13_SRC_BT_CFG09
-
IOMUXC_GPIO_B0_14_LCD_DATA10
-
IOMUXC_GPIO_B0_14_XBAR1_INOUT12
-
IOMUXC_GPIO_B0_14_ARM_CM7_TXEV
-
IOMUXC_GPIO_B0_14_SAI1_RX_SYNC
-
IOMUXC_GPIO_B0_14_FLEXIO2_D14
-
IOMUXC_GPIO_B0_14_GPIO2_IO14
-
IOMUXC_GPIO_B0_14_SRC_BT_CFG10
-
IOMUXC_GPIO_B0_15_LCD_DATA11
-
IOMUXC_GPIO_B0_15_XBAR1_INOUT13
-
IOMUXC_GPIO_B0_15_ARM_CM7_RXEV
-
IOMUXC_GPIO_B0_15_SAI1_RX_BCLK
-
IOMUXC_GPIO_B0_15_FLEXIO2_D15
-
IOMUXC_GPIO_B0_15_GPIO2_IO15
-
IOMUXC_GPIO_B0_15_SRC_BT_CFG11
-
IOMUXC_GPIO_B1_00_LCD_DATA12
-
IOMUXC_GPIO_B1_00_XBAR1_INOUT14
-
IOMUXC_GPIO_B1_00_LPUART4_TXD
-
IOMUXC_GPIO_B1_00_SAI1_RX_DATA00
-
IOMUXC_GPIO_B1_00_FLEXIO2_D16
-
IOMUXC_GPIO_B1_00_GPIO2_IO16
-
IOMUXC_GPIO_B1_00_FLEXPWM1_PWM3_A
-
IOMUXC_GPIO_B1_01_LCD_DATA13
-
IOMUXC_GPIO_B1_01_XBAR1_INOUT15
-
IOMUXC_GPIO_B1_01_LPUART4_RXD
-
IOMUXC_GPIO_B1_01_SAI1_TX_DATA00
-
IOMUXC_GPIO_B1_01_FLEXIO2_D17
-
IOMUXC_GPIO_B1_01_GPIO2_IO17
-
IOMUXC_GPIO_B1_01_FLEXPWM1_PWM3_B
-
IOMUXC_GPIO_B1_02_LCD_DATA14
-
IOMUXC_GPIO_B1_02_XBAR1_INOUT16
-
IOMUXC_GPIO_B1_02_LPSPI4_PCS2
-
IOMUXC_GPIO_B1_02_SAI1_TX_BCLK
-
IOMUXC_GPIO_B1_02_FLEXIO2_D18
-
IOMUXC_GPIO_B1_02_GPIO2_IO18
-
IOMUXC_GPIO_B1_02_FLEXPWM2_PWM3_A
-
IOMUXC_GPIO_B1_03_LCD_DATA15
-
IOMUXC_GPIO_B1_03_XBAR1_INOUT17
-
IOMUXC_GPIO_B1_03_LPSPI4_PCS1
-
IOMUXC_GPIO_B1_03_SAI1_TX_SYNC
-
IOMUXC_GPIO_B1_03_FLEXIO2_D19
-
IOMUXC_GPIO_B1_03_GPIO2_IO19
-
IOMUXC_GPIO_B1_03_FLEXPWM2_PWM3_B
-
IOMUXC_GPIO_B1_04_LCD_DATA16
-
IOMUXC_GPIO_B1_04_LPSPI4_PCS0
-
IOMUXC_GPIO_B1_04_CSI_DATA15
-
IOMUXC_GPIO_B1_04_ENET_RX_DATA00
-
IOMUXC_GPIO_B1_04_FLEXIO2_D20
-
IOMUXC_GPIO_B1_04_GPIO2_IO20
-
IOMUXC_GPIO_B1_05_LCD_DATA17
-
IOMUXC_GPIO_B1_05_LPSPI4_SDI
-
IOMUXC_GPIO_B1_05_CSI_DATA14
-
IOMUXC_GPIO_B1_05_ENET_RX_DATA01
-
IOMUXC_GPIO_B1_05_FLEXIO2_D21
-
IOMUXC_GPIO_B1_05_GPIO2_IO21
-
IOMUXC_GPIO_B1_06_LCD_DATA18
-
IOMUXC_GPIO_B1_06_LPSPI4_SDO
-
IOMUXC_GPIO_B1_06_CSI_DATA13
-
IOMUXC_GPIO_B1_06_ENET_RX_EN
-
IOMUXC_GPIO_B1_06_FLEXIO2_D22
-
IOMUXC_GPIO_B1_06_GPIO2_IO22
-
IOMUXC_GPIO_B1_07_LCD_DATA19
-
IOMUXC_GPIO_B1_07_LPSPI4_SCK
-
IOMUXC_GPIO_B1_07_CSI_DATA12
-
IOMUXC_GPIO_B1_07_ENET_TX_DATA00
-
IOMUXC_GPIO_B1_07_FLEXIO2_D23
-
IOMUXC_GPIO_B1_07_GPIO2_IO23
-
IOMUXC_GPIO_B1_08_LCD_DATA20
-
IOMUXC_GPIO_B1_08_TMR1_TIMER3
-
IOMUXC_GPIO_B1_08_CSI_DATA11
-
IOMUXC_GPIO_B1_08_ENET_TX_DATA01
-
IOMUXC_GPIO_B1_08_FLEXIO2_D24
-
IOMUXC_GPIO_B1_08_GPIO2_IO24
-
IOMUXC_GPIO_B1_08_FLEXCAN2_TX
-
IOMUXC_GPIO_B1_09_LCD_DATA21
-
IOMUXC_GPIO_B1_09_TMR2_TIMER3
-
IOMUXC_GPIO_B1_09_CSI_DATA10
-
IOMUXC_GPIO_B1_09_ENET_TX_EN
-
IOMUXC_GPIO_B1_09_FLEXIO2_D25
-
IOMUXC_GPIO_B1_09_GPIO2_IO25
-
IOMUXC_GPIO_B1_09_FLEXCAN2_RX
-
IOMUXC_GPIO_B1_10_LCD_DATA22
-
IOMUXC_GPIO_B1_10_TMR3_TIMER3
-
IOMUXC_GPIO_B1_10_CSI_DATA00
-
IOMUXC_GPIO_B1_10_ENET_TX_CLK
-
IOMUXC_GPIO_B1_10_FLEXIO2_D26
-
IOMUXC_GPIO_B1_10_GPIO2_IO26
-
IOMUXC_GPIO_B1_10_ENET_REF_CLK
-
IOMUXC_GPIO_B1_11_LCD_DATA23
-
IOMUXC_GPIO_B1_11_TMR4_TIMER3
-
IOMUXC_GPIO_B1_11_CSI_DATA01
-
IOMUXC_GPIO_B1_11_ENET_RX_ER
-
IOMUXC_GPIO_B1_11_FLEXIO2_D27
-
IOMUXC_GPIO_B1_11_GPIO2_IO27
-
IOMUXC_GPIO_B1_11_LPSPI4_PCS3
-
IOMUXC_GPIO_B1_12_LPUART5_TXD
-
IOMUXC_GPIO_B1_12_CSI_PIXCLK
-
IOMUXC_GPIO_B1_12_ENET_1588_EVENT0_IN
-
IOMUXC_GPIO_B1_12_FLEXIO2_D28
-
IOMUXC_GPIO_B1_12_GPIO2_IO28
-
IOMUXC_GPIO_B1_12_USDHC1_CD_B
-
IOMUXC_GPIO_B1_13_WDOG1_B
-
IOMUXC_GPIO_B1_13_LPUART5_RXD
-
IOMUXC_GPIO_B1_13_CSI_VSYNC
-
IOMUXC_GPIO_B1_13_ENET_1588_EVENT0_OUT
-
IOMUXC_GPIO_B1_13_FLEXIO2_D29
-
IOMUXC_GPIO_B1_13_GPIO2_IO29
-
IOMUXC_GPIO_B1_13_USDHC1_WP
-
IOMUXC_GPIO_B1_14_ENET_MDC
-
IOMUXC_GPIO_B1_14_FLEXPWM4_PWM2_A
-
IOMUXC_GPIO_B1_14_CSI_HSYNC
-
IOMUXC_GPIO_B1_14_XBAR1_IN02
-
IOMUXC_GPIO_B1_14_FLEXIO2_D30
-
IOMUXC_GPIO_B1_14_GPIO2_IO30
-
IOMUXC_GPIO_B1_14_USDHC1_VSELECT
-
IOMUXC_GPIO_B1_15_ENET_MDIO
-
IOMUXC_GPIO_B1_15_FLEXPWM4_PWM3_A
-
IOMUXC_GPIO_B1_15_CSI_MCLK
-
IOMUXC_GPIO_B1_15_XBAR1_IN03
-
IOMUXC_GPIO_B1_15_FLEXIO2_D31
-
IOMUXC_GPIO_B1_15_GPIO2_IO31
-
IOMUXC_GPIO_B1_15_USDHC1_RESET_B
-
IOMUXC_GPIO_SD_B0_00_USDHC1_CMD
-
IOMUXC_GPIO_SD_B0_00_FLEXPWM1_PWM0_A
-
IOMUXC_GPIO_SD_B0_00_LPI2C3_SCL
-
IOMUXC_GPIO_SD_B0_00_XBAR1_INOUT04
-
IOMUXC_GPIO_SD_B0_00_LPSPI1_SCK
-
IOMUXC_GPIO_SD_B0_00_GPIO3_IO12
-
IOMUXC_GPIO_SD_B0_00_FLEXSPI_A_SS1_B
-
IOMUXC_GPIO_SD_B0_01_USDHC1_CLK
-
IOMUXC_GPIO_SD_B0_01_FLEXPWM1_PWM0_B
-
IOMUXC_GPIO_SD_B0_01_LPI2C3_SDA
-
IOMUXC_GPIO_SD_B0_01_XBAR1_INOUT05
-
IOMUXC_GPIO_SD_B0_01_LPSPI1_PCS0
-
IOMUXC_GPIO_SD_B0_01_GPIO3_IO13
-
IOMUXC_GPIO_SD_B0_01_FLEXSPI_B_SS1_B
-
IOMUXC_GPIO_SD_B0_02_USDHC1_DATA0
-
IOMUXC_GPIO_SD_B0_02_FLEXPWM1_PWM1_A
-
IOMUXC_GPIO_SD_B0_02_LPUART8_CTS_B
-
IOMUXC_GPIO_SD_B0_02_XBAR1_INOUT06
-
IOMUXC_GPIO_SD_B0_02_LPSPI1_SDO
-
IOMUXC_GPIO_SD_B0_02_GPIO3_IO14
-
IOMUXC_GPIO_SD_B0_03_USDHC1_DATA1
-
IOMUXC_GPIO_SD_B0_03_FLEXPWM1_PWM1_B
-
IOMUXC_GPIO_SD_B0_03_LPUART8_RTS_B
-
IOMUXC_GPIO_SD_B0_03_XBAR1_INOUT07
-
IOMUXC_GPIO_SD_B0_03_LPSPI1_SDI
-
IOMUXC_GPIO_SD_B0_03_GPIO3_IO15
-
IOMUXC_GPIO_SD_B0_04_USDHC1_DATA2
-
IOMUXC_GPIO_SD_B0_04_FLEXPWM1_PWM2_A
-
IOMUXC_GPIO_SD_B0_04_LPUART8_TXD
-
IOMUXC_GPIO_SD_B0_04_XBAR1_INOUT08
-
IOMUXC_GPIO_SD_B0_04_FLEXSPI_B_SS0_B
-
IOMUXC_GPIO_SD_B0_04_GPIO3_IO16
-
IOMUXC_GPIO_SD_B0_04_CCM_CLKO1
-
IOMUXC_GPIO_SD_B0_05_USDHC1_DATA3
-
IOMUXC_GPIO_SD_B0_05_FLEXPWM1_PWM2_B
-
IOMUXC_GPIO_SD_B0_05_LPUART8_RXD
-
IOMUXC_GPIO_SD_B0_05_XBAR1_INOUT09
-
IOMUXC_GPIO_SD_B0_05_FLEXSPI_B_DQS
-
IOMUXC_GPIO_SD_B0_05_GPIO3_IO17
-
IOMUXC_GPIO_SD_B0_05_CCM_CLKO2
-
IOMUXC_GPIO_SD_B1_00_USDHC2_DATA3
-
IOMUXC_GPIO_SD_B1_00_FLEXSPI_B_DATA3
-
IOMUXC_GPIO_SD_B1_00_FLEXPWM1_PWM3_A
-
IOMUXC_GPIO_SD_B1_00_SAI1_TX_DATA03
-
IOMUXC_GPIO_SD_B1_00_LPUART4_TXD
-
IOMUXC_GPIO_SD_B1_00_GPIO3_IO00
-
IOMUXC_GPIO_SD_B1_01_USDHC2_DATA2
-
IOMUXC_GPIO_SD_B1_01_FLEXSPI_B_DATA2
-
IOMUXC_GPIO_SD_B1_01_FLEXPWM1_PWM3_B
-
IOMUXC_GPIO_SD_B1_01_SAI1_TX_DATA02
-
IOMUXC_GPIO_SD_B1_01_LPUART4_RXD
-
IOMUXC_GPIO_SD_B1_01_GPIO3_IO01
-
IOMUXC_GPIO_SD_B1_02_USDHC2_DATA1
-
IOMUXC_GPIO_SD_B1_02_FLEXSPI_B_DATA1
-
IOMUXC_GPIO_SD_B1_02_FLEXPWM2_PWM3_A
-
IOMUXC_GPIO_SD_B1_02_SAI1_TX_DATA01
-
IOMUXC_GPIO_SD_B1_02_FLEXCAN1_TX
-
IOMUXC_GPIO_SD_B1_02_GPIO3_IO02
-
IOMUXC_GPIO_SD_B1_02_CCM_WAIT
-
IOMUXC_GPIO_SD_B1_03_USDHC2_DATA0
-
IOMUXC_GPIO_SD_B1_03_FLEXSPI_B_DATA0
-
IOMUXC_GPIO_SD_B1_03_FLEXPWM2_PWM3_B
-
IOMUXC_GPIO_SD_B1_03_SAI1_MCLK
-
IOMUXC_GPIO_SD_B1_03_FLEXCAN1_RX
-
IOMUXC_GPIO_SD_B1_03_GPIO3_IO03
-
IOMUXC_GPIO_SD_B1_03_CCM_PMIC_READY
-
IOMUXC_GPIO_SD_B1_04_USDHC2_CLK
-
IOMUXC_GPIO_SD_B1_04_FLEXSPI_B_SCLK
-
IOMUXC_GPIO_SD_B1_04_LPI2C1_SCL
-
IOMUXC_GPIO_SD_B1_04_SAI1_RX_SYNC
-
IOMUXC_GPIO_SD_B1_04_FLEXSPI_A_SS1_B
-
IOMUXC_GPIO_SD_B1_04_GPIO3_IO04
-
IOMUXC_GPIO_SD_B1_04_CCM_STOP
-
IOMUXC_GPIO_SD_B1_05_USDHC2_CMD
-
IOMUXC_GPIO_SD_B1_05_FLEXSPI_A_DQS
-
IOMUXC_GPIO_SD_B1_05_LPI2C1_SDA
-
IOMUXC_GPIO_SD_B1_05_SAI1_RX_BCLK
-
IOMUXC_GPIO_SD_B1_05_FLEXSPI_B_SS0_B
-
IOMUXC_GPIO_SD_B1_05_GPIO3_IO05
-
IOMUXC_GPIO_SD_B1_06_USDHC2_RESET_B
-
IOMUXC_GPIO_SD_B1_06_FLEXSPI_A_SS0_B
-
IOMUXC_GPIO_SD_B1_06_LPUART7_CTS_B
-
IOMUXC_GPIO_SD_B1_06_SAI1_RX_DATA00
-
IOMUXC_GPIO_SD_B1_06_LPSPI2_PCS0
-
IOMUXC_GPIO_SD_B1_06_GPIO3_IO06
-
IOMUXC_GPIO_SD_B1_07_SEMC_CSX1
-
IOMUXC_GPIO_SD_B1_07_FLEXSPI_A_SCLK
-
IOMUXC_GPIO_SD_B1_07_LPUART7_RTS_B
-
IOMUXC_GPIO_SD_B1_07_SAI1_TX_DATA00
-
IOMUXC_GPIO_SD_B1_07_LPSPI2_SCK
-
IOMUXC_GPIO_SD_B1_07_GPIO3_IO07
-
IOMUXC_GPIO_SD_B1_07_CCM_REF_EN_B
-
IOMUXC_GPIO_SD_B1_08_USDHC2_DATA4
-
IOMUXC_GPIO_SD_B1_08_FLEXSPI_A_DATA00
-
IOMUXC_GPIO_SD_B1_08_LPUART7_TXD
-
IOMUXC_GPIO_SD_B1_08_SAI1_TX_BCLK
-
IOMUXC_GPIO_SD_B1_08_LPSPI2_SD0
-
IOMUXC_GPIO_SD_B1_08_GPIO3_IO08
-
IOMUXC_GPIO_SD_B1_08_SEMC_CSX2
-
IOMUXC_GPIO_SD_B1_09_USDHC2_DATA5
-
IOMUXC_GPIO_SD_B1_09_FLEXSPI_A_DATA1
-
IOMUXC_GPIO_SD_B1_09_LPUART7_RXD
-
IOMUXC_GPIO_SD_B1_09_SAI1_TX_SYNC
-
IOMUXC_GPIO_SD_B1_09_LPSPI2_SDI
-
IOMUXC_GPIO_SD_B1_09_GPIO3_IO09
-
IOMUXC_GPIO_SD_B1_10_USDHC2_DATA6
-
IOMUXC_GPIO_SD_B1_10_FLEXSPI_A_DATA2
-
IOMUXC_GPIO_SD_B1_10_LPUART2_RXD
-
IOMUXC_GPIO_SD_B1_10_LPI2C2_SDA
-
IOMUXC_GPIO_SD_B1_10_LPSPI2_PCS2
-
IOMUXC_GPIO_SD_B1_10_GPIO3_IO10
-
IOMUXC_GPIO_SD_B1_11_USDHC2_DATA7
-
IOMUXC_GPIO_SD_B1_11_FLEXSPI_A_DATA3
-
IOMUXC_GPIO_SD_B1_11_LPUART2_TXD
-
IOMUXC_GPIO_SD_B1_11_LPI2C2_SCL
-
IOMUXC_GPIO_SD_B1_11_LPSPI2_PCS3
-
IOMUXC_GPIO_SD_B1_11_GPIO3_IO11
-
IOMUXC_SNVS_WAKEUP_GPIO5_IO00
-
IOMUXC_SNVS_WAKEUP_NMI
-
IOMUXC_SNVS_PMIC_ON_REQ_SNVS_PMIC_ON_REQ
-
IOMUXC_SNVS_PMIC_ON_REQ_GPIO5_IO01
-
IOMUXC_SNVS_PMIC_STBY_REQ_CCM_PMIC_STBY_REQ
-
IOMUXC_SNVS_PMIC_STBY_REQ_GPIO5_IO02
-
IOMUXC_SNVS_TEST_MODE
-
IOMUXC_SNVS_POR_B
-
IOMUXC_SNVS_ONOFF
-
IOMUXC_GPR_SAIMCLK_LOWBITMASK
-
IOMUXC_GPR_SAIMCLK_HIGHBITMASK
-
static inline void IOMUXC_SetPinMux(uint32_t muxRegister, uint32_t muxMode, uint32_t inputRegister, uint32_t inputDaisy, uint32_t configRegister, uint32_t inputOnfield)
Sets the IOMUXC pin mux mode.
This is an example to set the PTA6 as the lpuart0_tx:
IOMUXC_SetPinMux(IOMUXC_PTA6_LPUART0_TX, 0);
This is an example to set the PTA0 as GPIOA0:
IOMUXC_SetPinMux(IOMUXC_PTA0_GPIOA0, 0);
Note
The first five parameters can be filled with the pin function ID macros.
- Parameters:
muxRegister – The pin mux register.
muxMode – The pin mux mode.
inputRegister – The select input register.
inputDaisy – The input daisy.
configRegister – The config register.
inputOnfield – Software input on field.
-
static inline void IOMUXC_SetPinConfig(uint32_t muxRegister, uint32_t muxMode, uint32_t inputRegister, uint32_t inputDaisy, uint32_t configRegister, uint32_t configValue)
Sets the IOMUXC pin configuration.
This is an example to set pin configuration for IOMUXC_PTA3_LPI2C0_SCLS:
IOMUXC_SetPinConfig(IOMUXC_PTA3_LPI2C0_SCLS,IOMUXC_SW_PAD_CTL_PAD_PUS_MASK|IOMUXC_SW_PAD_CTL_PAD_PUS(2U))
Note
The previous five parameters can be filled with the pin function ID macros.
- Parameters:
muxRegister – The pin mux register.
muxMode – The pin mux mode.
inputRegister – The select input register.
inputDaisy – The input daisy.
configRegister – The config register.
configValue – The pin config value.
-
static inline void IOMUXC_EnableMode(IOMUXC_GPR_Type *base, uint32_t mode, bool enable)
Sets IOMUXC general configuration for some mode.
- Parameters:
base – The IOMUXC GPR base address.
mode – The mode for setting. the mode is the logical OR of “iomuxc_gpr_mode”
enable – True enable false disable.
-
static inline void IOMUXC_SetSaiMClkClockSource(IOMUXC_GPR_Type *base, iomuxc_gpr_saimclk_t mclk, uint8_t clkSrc)
Sets IOMUXC general configuration for SAI MCLK selection.
- Parameters:
base – The IOMUXC GPR base address.
mclk – The SAI MCLK.
clkSrc – The clock source. Take refer to register setting details for the clock source in RM.
-
static inline void IOMUXC_MQSEnterSoftwareReset(IOMUXC_GPR_Type *base, bool enable)
Enters or exit MQS software reset.
- Parameters:
base – The IOMUXC GPR base address.
enable – Enter or exit MQS software reset.
-
static inline void IOMUXC_MQSEnable(IOMUXC_GPR_Type *base, bool enable)
Enables or disables MQS.
- Parameters:
base – The IOMUXC GPR base address.
enable – Enable or disable the MQS.
-
static inline void IOMUXC_MQSConfig(IOMUXC_GPR_Type *base, iomuxc_mqs_pwm_oversample_rate_t rate, uint8_t divider)
Configure MQS PWM oversampling rate compared with mclk and divider ratio control for mclk from hmclk.
- Parameters:
base – The IOMUXC GPR base address.
rate – The MQS PWM oversampling rate, refer to “iomuxc_mqs_pwm_oversample_rate_t”.
divider – The divider ratio control for mclk from hmclk. mclk freq = 1 /(divider + 1) * hmclk freq.
-
FSL_IOMUXC_DRIVER_VERSION
IOMUXC driver version 2.0.2.
-
FSL_COMPONENT_ID
KPP: KeyPad Port Driver
-
void KPP_Init(KPP_Type *base, kpp_config_t *configure)
KPP initialize. This function ungates the KPP clock and initializes KPP. This function must be called before calling any other KPP driver functions.
- Parameters:
base – KPP peripheral base address.
configure – The KPP configuration structure pointer.
-
void KPP_Deinit(KPP_Type *base)
Deinitializes the KPP module and gates the clock. This function gates the KPP clock. As a result, the KPP module doesn’t work after calling this function.
- Parameters:
base – KPP peripheral base address.
-
static inline void KPP_EnableInterrupts(KPP_Type *base, uint16_t mask)
Enable the interrupt.
- Parameters:
base – KPP peripheral base address.
mask – KPP interrupts to enable. This is a logical OR of the enumeration :: kpp_interrupt_enable_t.
-
static inline void KPP_DisableInterrupts(KPP_Type *base, uint16_t mask)
Disable the interrupt.
- Parameters:
base – KPP peripheral base address.
mask – KPP interrupts to disable. This is a logical OR of the enumeration :: kpp_interrupt_enable_t.
-
static inline uint16_t KPP_GetStatusFlag(KPP_Type *base)
Gets the KPP interrupt event status.
- Parameters:
base – KPP peripheral base address.
- Returns:
The status of the KPP. Application can use the enum type in the “kpp_interrupt_enable_t” to get the right status of the related event.
-
static inline void KPP_ClearStatusFlag(KPP_Type *base, uint16_t mask)
Clears KPP status flag.
- Parameters:
base – KPP peripheral base address.
mask – KPP mask to be cleared. This is a logical OR of the enumeration :: kpp_interrupt_enable_t.
-
static inline void KPP_SetSynchronizeChain(KPP_Type *base, uint16_t mask)
Set KPP synchronization chain.
- Parameters:
base – KPP peripheral base address.
mask – KPP mask to be cleared. This is a logical OR of the enumeration :: kpp_sync_operation_t.
-
void KPP_keyPressScanning(KPP_Type *base, uint8_t *data, uint32_t clockSrc_Hz)
Keypad press scanning.
This function will scanning all columns and rows. so all scanning data will be stored in the data pointer.
- Parameters:
base – KPP peripheral base address.
data – KPP key press scanning data. The data buffer should be prepared with length at least equal to KPP_KEYPAD_COLUMNNUM_MAX * KPP_KEYPAD_ROWNUM_MAX. the data pointer is recommended to be a array like uint8_t data[KPP_KEYPAD_COLUMNNUM_MAX]. for example the data[2] = 4, that means in column 1 row 2 has a key press event.
clockSrc_Hz – Source clock.
-
FSL_KPP_DRIVER_VERSION
KPP driver version.
-
enum _kpp_interrupt_enable
List of interrupts supported by the peripheral. This enumeration uses one-bot encoding to allow a logical OR of multiple members. Members usually map to interrupt enable bits in one or more peripheral registers.
Values:
-
enumerator kKPP_keyDepressInterrupt
Keypad depress interrupt source
-
enumerator kKPP_keyReleaseInterrupt
Keypad release interrupt source
-
enumerator kKPP_keyDepressInterrupt
-
enum _kpp_sync_operation
Lists of KPP synchronize chain operation.
Values:
-
enumerator kKPP_ClearKeyDepressSyncChain
Keypad depress interrupt status.
-
enumerator kKPP_SetKeyReleasesSyncChain
Keypad release interrupt status.
-
enumerator kKPP_ClearKeyDepressSyncChain
-
typedef enum _kpp_interrupt_enable kpp_interrupt_enable_t
List of interrupts supported by the peripheral. This enumeration uses one-bot encoding to allow a logical OR of multiple members. Members usually map to interrupt enable bits in one or more peripheral registers.
-
typedef enum _kpp_sync_operation kpp_sync_operation_t
Lists of KPP synchronize chain operation.
-
typedef struct _kpp_config kpp_config_t
Lists of KPP status.
-
KPP_KEYPAD_COLUMNNUM_MAX
-
KPP_KEYPAD_ROWNUM_MAX
-
struct _kpp_config
- #include <fsl_kpp.h>
Lists of KPP status.
Public Members
-
uint8_t activeRow
The row number: bit 7 ~ 0 represents the row 7 ~ 0.
-
uint8_t activeColumn
The column number: bit 7 ~ 0 represents the column 7 ~ 0.
-
uint16_t interrupt
KPP interrupt source. A logical OR of “kpp_interrupt_enable_t”.
-
uint8_t activeRow
Common Driver
-
FSL_COMMON_DRIVER_VERSION
common driver version.
-
DEBUG_CONSOLE_DEVICE_TYPE_NONE
No debug console.
-
DEBUG_CONSOLE_DEVICE_TYPE_UART
Debug console based on UART.
-
DEBUG_CONSOLE_DEVICE_TYPE_LPUART
Debug console based on LPUART.
-
DEBUG_CONSOLE_DEVICE_TYPE_LPSCI
Debug console based on LPSCI.
-
DEBUG_CONSOLE_DEVICE_TYPE_USBCDC
Debug console based on USBCDC.
-
DEBUG_CONSOLE_DEVICE_TYPE_FLEXCOMM
Debug console based on FLEXCOMM.
-
DEBUG_CONSOLE_DEVICE_TYPE_IUART
Debug console based on i.MX UART.
-
DEBUG_CONSOLE_DEVICE_TYPE_VUSART
Debug console based on LPC_VUSART.
-
DEBUG_CONSOLE_DEVICE_TYPE_MINI_USART
Debug console based on LPC_USART.
-
DEBUG_CONSOLE_DEVICE_TYPE_SWO
Debug console based on SWO.
-
DEBUG_CONSOLE_DEVICE_TYPE_QSCI
Debug console based on QSCI.
-
MIN(a, b)
Computes the minimum of a and b.
-
MAX(a, b)
Computes the maximum of a and b.
-
UINT16_MAX
Max value of uint16_t type.
-
UINT32_MAX
Max value of uint32_t type.
-
SDK_ATOMIC_LOCAL_ADD(addr, val)
Add value val from the variable at address address.
-
SDK_ATOMIC_LOCAL_SUB(addr, val)
Subtract value val to the variable at address address.
-
SDK_ATOMIC_LOCAL_SET(addr, bits)
Set the bits specifiled by bits to the variable at address address.
-
SDK_ATOMIC_LOCAL_CLEAR(addr, bits)
Clear the bits specifiled by bits to the variable at address address.
-
SDK_ATOMIC_LOCAL_TOGGLE(addr, bits)
Toggle the bits specifiled by bits to the variable at address address.
-
SDK_ATOMIC_LOCAL_CLEAR_AND_SET(addr, clearBits, setBits)
For the variable at address address, clear the bits specifiled by clearBits and set the bits specifiled by setBits.
-
SDK_ATOMIC_LOCAL_COMPARE_AND_SET(addr, expected, newValue)
For the variable at address address, check whether the value equal to expected. If value same as expected then update newValue to address and return true , else return false .
-
SDK_ATOMIC_LOCAL_TEST_AND_SET(addr, newValue)
For the variable at address address, set as newValue value and return old value.
-
USEC_TO_COUNT(us, clockFreqInHz)
Macro to convert a microsecond period to raw count value
-
COUNT_TO_USEC(count, clockFreqInHz)
Macro to convert a raw count value to microsecond
-
MSEC_TO_COUNT(ms, clockFreqInHz)
Macro to convert a millisecond period to raw count value
-
COUNT_TO_MSEC(count, clockFreqInHz)
Macro to convert a raw count value to millisecond
-
SDK_ISR_EXIT_BARRIER
-
SDK_L1DCACHE_ALIGN(var)
Macro to define a variable with L1 d-cache line size alignment
-
SDK_SIZEALIGN(var, alignbytes)
Macro to define a variable with L2 cache line size alignment
Macro to change a value to a given size aligned value
-
CACHE_LINE_DATA
-
enum _status_groups
Status group numbers.
Values:
-
enumerator kStatusGroup_Generic
Group number for generic status codes.
-
enumerator kStatusGroup_FLASH
Group number for FLASH status codes.
-
enumerator kStatusGroup_LPSPI
Group number for LPSPI status codes.
-
enumerator kStatusGroup_FLEXIO_SPI
Group number for FLEXIO SPI status codes.
-
enumerator kStatusGroup_DSPI
Group number for DSPI status codes.
-
enumerator kStatusGroup_FLEXIO_UART
Group number for FLEXIO UART status codes.
-
enumerator kStatusGroup_FLEXIO_I2C
Group number for FLEXIO I2C status codes.
-
enumerator kStatusGroup_LPI2C
Group number for LPI2C status codes.
-
enumerator kStatusGroup_UART
Group number for UART status codes.
-
enumerator kStatusGroup_I2C
Group number for UART status codes.
-
enumerator kStatusGroup_LPSCI
Group number for LPSCI status codes.
-
enumerator kStatusGroup_LPUART
Group number for LPUART status codes.
-
enumerator kStatusGroup_SPI
Group number for SPI status code.
-
enumerator kStatusGroup_XRDC
Group number for XRDC status code.
-
enumerator kStatusGroup_SEMA42
Group number for SEMA42 status code.
-
enumerator kStatusGroup_SDHC
Group number for SDHC status code
-
enumerator kStatusGroup_SDMMC
Group number for SDMMC status code
-
enumerator kStatusGroup_SAI
Group number for SAI status code
-
enumerator kStatusGroup_MCG
Group number for MCG status codes.
-
enumerator kStatusGroup_SCG
Group number for SCG status codes.
-
enumerator kStatusGroup_SDSPI
Group number for SDSPI status codes.
-
enumerator kStatusGroup_FLEXIO_I2S
Group number for FLEXIO I2S status codes
-
enumerator kStatusGroup_FLEXIO_MCULCD
Group number for FLEXIO LCD status codes
-
enumerator kStatusGroup_FLASHIAP
Group number for FLASHIAP status codes
-
enumerator kStatusGroup_FLEXCOMM_I2C
Group number for FLEXCOMM I2C status codes
-
enumerator kStatusGroup_I2S
Group number for I2S status codes
-
enumerator kStatusGroup_IUART
Group number for IUART status codes
-
enumerator kStatusGroup_CSI
Group number for CSI status codes
-
enumerator kStatusGroup_MIPI_DSI
Group number for MIPI DSI status codes
-
enumerator kStatusGroup_SDRAMC
Group number for SDRAMC status codes.
-
enumerator kStatusGroup_POWER
Group number for POWER status codes.
-
enumerator kStatusGroup_ENET
Group number for ENET status codes.
-
enumerator kStatusGroup_PHY
Group number for PHY status codes.
-
enumerator kStatusGroup_TRGMUX
Group number for TRGMUX status codes.
-
enumerator kStatusGroup_SMARTCARD
Group number for SMARTCARD status codes.
-
enumerator kStatusGroup_LMEM
Group number for LMEM status codes.
-
enumerator kStatusGroup_QSPI
Group number for QSPI status codes.
-
enumerator kStatusGroup_DMA
Group number for DMA status codes.
-
enumerator kStatusGroup_EDMA
Group number for EDMA status codes.
-
enumerator kStatusGroup_DMAMGR
Group number for DMAMGR status codes.
-
enumerator kStatusGroup_FLEXCAN
Group number for FlexCAN status codes.
-
enumerator kStatusGroup_LTC
Group number for LTC status codes.
-
enumerator kStatusGroup_FLEXIO_CAMERA
Group number for FLEXIO CAMERA status codes.
-
enumerator kStatusGroup_LPC_SPI
Group number for LPC_SPI status codes.
-
enumerator kStatusGroup_LPC_USART
Group number for LPC_USART status codes.
-
enumerator kStatusGroup_DMIC
Group number for DMIC status codes.
-
enumerator kStatusGroup_SDIF
Group number for SDIF status codes.
-
enumerator kStatusGroup_SPIFI
Group number for SPIFI status codes.
-
enumerator kStatusGroup_OTP
Group number for OTP status codes.
-
enumerator kStatusGroup_MCAN
Group number for MCAN status codes.
-
enumerator kStatusGroup_CAAM
Group number for CAAM status codes.
-
enumerator kStatusGroup_ECSPI
Group number for ECSPI status codes.
-
enumerator kStatusGroup_USDHC
Group number for USDHC status codes.
-
enumerator kStatusGroup_LPC_I2C
Group number for LPC_I2C status codes.
-
enumerator kStatusGroup_DCP
Group number for DCP status codes.
-
enumerator kStatusGroup_MSCAN
Group number for MSCAN status codes.
-
enumerator kStatusGroup_ESAI
Group number for ESAI status codes.
-
enumerator kStatusGroup_FLEXSPI
Group number for FLEXSPI status codes.
-
enumerator kStatusGroup_MMDC
Group number for MMDC status codes.
-
enumerator kStatusGroup_PDM
Group number for MIC status codes.
-
enumerator kStatusGroup_SDMA
Group number for SDMA status codes.
-
enumerator kStatusGroup_ICS
Group number for ICS status codes.
-
enumerator kStatusGroup_SPDIF
Group number for SPDIF status codes.
-
enumerator kStatusGroup_LPC_MINISPI
Group number for LPC_MINISPI status codes.
-
enumerator kStatusGroup_HASHCRYPT
Group number for Hashcrypt status codes
-
enumerator kStatusGroup_LPC_SPI_SSP
Group number for LPC_SPI_SSP status codes.
-
enumerator kStatusGroup_I3C
Group number for I3C status codes
-
enumerator kStatusGroup_LPC_I2C_1
Group number for LPC_I2C_1 status codes.
-
enumerator kStatusGroup_NOTIFIER
Group number for NOTIFIER status codes.
-
enumerator kStatusGroup_DebugConsole
Group number for debug console status codes.
-
enumerator kStatusGroup_SEMC
Group number for SEMC status codes.
-
enumerator kStatusGroup_ApplicationRangeStart
Starting number for application groups.
-
enumerator kStatusGroup_IAP
Group number for IAP status codes
-
enumerator kStatusGroup_SFA
Group number for SFA status codes
-
enumerator kStatusGroup_SPC
Group number for SPC status codes.
-
enumerator kStatusGroup_PUF
Group number for PUF status codes.
-
enumerator kStatusGroup_TOUCH_PANEL
Group number for touch panel status codes
-
enumerator kStatusGroup_VBAT
Group number for VBAT status codes
-
enumerator kStatusGroup_XSPI
Group number for XSPI status codes
-
enumerator kStatusGroup_PNGDEC
Group number for PNGDEC status codes
-
enumerator kStatusGroup_JPEGDEC
Group number for JPEGDEC status codes
-
enumerator kStatusGroup_HAL_GPIO
Group number for HAL GPIO status codes.
-
enumerator kStatusGroup_HAL_UART
Group number for HAL UART status codes.
-
enumerator kStatusGroup_HAL_TIMER
Group number for HAL TIMER status codes.
-
enumerator kStatusGroup_HAL_SPI
Group number for HAL SPI status codes.
-
enumerator kStatusGroup_HAL_I2C
Group number for HAL I2C status codes.
-
enumerator kStatusGroup_HAL_FLASH
Group number for HAL FLASH status codes.
-
enumerator kStatusGroup_HAL_PWM
Group number for HAL PWM status codes.
-
enumerator kStatusGroup_HAL_RNG
Group number for HAL RNG status codes.
-
enumerator kStatusGroup_HAL_I2S
Group number for HAL I2S status codes.
-
enumerator kStatusGroup_HAL_ADC_SENSOR
Group number for HAL ADC SENSOR status codes.
-
enumerator kStatusGroup_TIMERMANAGER
Group number for TiMER MANAGER status codes.
-
enumerator kStatusGroup_SERIALMANAGER
Group number for SERIAL MANAGER status codes.
-
enumerator kStatusGroup_LED
Group number for LED status codes.
-
enumerator kStatusGroup_BUTTON
Group number for BUTTON status codes.
-
enumerator kStatusGroup_EXTERN_EEPROM
Group number for EXTERN EEPROM status codes.
-
enumerator kStatusGroup_SHELL
Group number for SHELL status codes.
-
enumerator kStatusGroup_MEM_MANAGER
Group number for MEM MANAGER status codes.
-
enumerator kStatusGroup_LIST
Group number for List status codes.
-
enumerator kStatusGroup_OSA
Group number for OSA status codes.
-
enumerator kStatusGroup_COMMON_TASK
Group number for Common task status codes.
-
enumerator kStatusGroup_MSG
Group number for messaging status codes.
-
enumerator kStatusGroup_SDK_OCOTP
Group number for OCOTP status codes.
-
enumerator kStatusGroup_SDK_FLEXSPINOR
Group number for FLEXSPINOR status codes.
-
enumerator kStatusGroup_CODEC
Group number for codec status codes.
-
enumerator kStatusGroup_ASRC
Group number for codec status ASRC.
-
enumerator kStatusGroup_OTFAD
Group number for codec status codes.
-
enumerator kStatusGroup_SDIOSLV
Group number for SDIOSLV status codes.
-
enumerator kStatusGroup_MECC
Group number for MECC status codes.
-
enumerator kStatusGroup_ENET_QOS
Group number for ENET_QOS status codes.
-
enumerator kStatusGroup_LOG
Group number for LOG status codes.
-
enumerator kStatusGroup_I3CBUS
Group number for I3CBUS status codes.
-
enumerator kStatusGroup_QSCI
Group number for QSCI status codes.
-
enumerator kStatusGroup_ELEMU
Group number for ELEMU status codes.
-
enumerator kStatusGroup_QUEUEDSPI
Group number for QSPI status codes.
-
enumerator kStatusGroup_POWER_MANAGER
Group number for POWER_MANAGER status codes.
-
enumerator kStatusGroup_IPED
Group number for IPED status codes.
-
enumerator kStatusGroup_ELS_PKC
Group number for ELS PKC status codes.
-
enumerator kStatusGroup_CSS_PKC
Group number for CSS PKC status codes.
-
enumerator kStatusGroup_HOSTIF
Group number for HOSTIF status codes.
-
enumerator kStatusGroup_CLIF
Group number for CLIF status codes.
-
enumerator kStatusGroup_BMA
Group number for BMA status codes.
-
enumerator kStatusGroup_NETC
Group number for NETC status codes.
-
enumerator kStatusGroup_ELE
Group number for ELE status codes.
-
enumerator kStatusGroup_GLIKEY
Group number for GLIKEY status codes.
-
enumerator kStatusGroup_AON_POWER
Group number for AON_POWER status codes.
-
enumerator kStatusGroup_AON_COMMON
Group number for AON_COMMON status codes.
-
enumerator kStatusGroup_ENDAT3
Group number for ENDAT3 status codes.
-
enumerator kStatusGroup_HIPERFACE
Group number for HIPERFACE status codes.
-
enumerator kStatusGroup_Generic
Generic status return codes.
Values:
-
enumerator kStatus_Success
Generic status for Success.
-
enumerator kStatus_Fail
Generic status for Fail.
-
enumerator kStatus_ReadOnly
Generic status for read only failure.
-
enumerator kStatus_OutOfRange
Generic status for out of range access.
-
enumerator kStatus_InvalidArgument
Generic status for invalid argument check.
-
enumerator kStatus_Timeout
Generic status for timeout.
-
enumerator kStatus_NoTransferInProgress
Generic status for no transfer in progress.
-
enumerator kStatus_Busy
Generic status for module is busy.
-
enumerator kStatus_NoData
Generic status for no data is found for the operation.
-
enumerator kStatus_Success
-
typedef int32_t status_t
Type used for all status and error return values.
-
void *SDK_Malloc(size_t size, size_t alignbytes)
Allocate memory with given alignment and aligned size.
This is provided to support the dynamically allocated memory used in cache-able region.
- Parameters:
size – The length required to malloc.
alignbytes – The alignment size.
- Return values:
The – allocated memory.
-
void SDK_Free(void *ptr)
Free memory.
- Parameters:
ptr – The memory to be release.
-
void SDK_DelayAtLeastUs(uint32_t delayTime_us, uint32_t coreClock_Hz)
Delay at least for some time. Please note that, this API uses while loop for delay, different run-time environments make the time not precise, if precise delay count was needed, please implement a new delay function with hardware timer.
- Parameters:
delayTime_us – Delay time in unit of microsecond.
coreClock_Hz – Core clock frequency with Hz.
-
static inline status_t EnableIRQ(IRQn_Type interrupt)
Enable specific interrupt.
Enable LEVEL1 interrupt. For some devices, there might be multiple interrupt levels. For example, there are NVIC and intmux. Here the interrupts connected to NVIC are the LEVEL1 interrupts, because they are routed to the core directly. The interrupts connected to intmux are the LEVEL2 interrupts, they are routed to NVIC first then routed to core.
This function only enables the LEVEL1 interrupts. The number of LEVEL1 interrupts is indicated by the feature macro FSL_FEATURE_NUMBER_OF_LEVEL1_INT_VECTORS.
- Parameters:
interrupt – The IRQ number.
- Return values:
kStatus_Success – Interrupt enabled successfully
kStatus_Fail – Failed to enable the interrupt
-
static inline status_t DisableIRQ(IRQn_Type interrupt)
Disable specific interrupt.
Disable LEVEL1 interrupt. For some devices, there might be multiple interrupt levels. For example, there are NVIC and intmux. Here the interrupts connected to NVIC are the LEVEL1 interrupts, because they are routed to the core directly. The interrupts connected to intmux are the LEVEL2 interrupts, they are routed to NVIC first then routed to core.
This function only disables the LEVEL1 interrupts. The number of LEVEL1 interrupts is indicated by the feature macro FSL_FEATURE_NUMBER_OF_LEVEL1_INT_VECTORS.
- Parameters:
interrupt – The IRQ number.
- Return values:
kStatus_Success – Interrupt disabled successfully
kStatus_Fail – Failed to disable the interrupt
-
static inline status_t EnableIRQWithPriority(IRQn_Type interrupt, uint8_t priNum)
Enable the IRQ, and also set the interrupt priority.
Only handle LEVEL1 interrupt. For some devices, there might be multiple interrupt levels. For example, there are NVIC and intmux. Here the interrupts connected to NVIC are the LEVEL1 interrupts, because they are routed to the core directly. The interrupts connected to intmux are the LEVEL2 interrupts, they are routed to NVIC first then routed to core.
This function only handles the LEVEL1 interrupts. The number of LEVEL1 interrupts is indicated by the feature macro FSL_FEATURE_NUMBER_OF_LEVEL1_INT_VECTORS.
- Parameters:
interrupt – The IRQ to Enable.
priNum – Priority number set to interrupt controller register.
- Return values:
kStatus_Success – Interrupt priority set successfully
kStatus_Fail – Failed to set the interrupt priority.
-
static inline status_t IRQ_SetPriority(IRQn_Type interrupt, uint8_t priNum)
Set the IRQ priority.
Only handle LEVEL1 interrupt. For some devices, there might be multiple interrupt levels. For example, there are NVIC and intmux. Here the interrupts connected to NVIC are the LEVEL1 interrupts, because they are routed to the core directly. The interrupts connected to intmux are the LEVEL2 interrupts, they are routed to NVIC first then routed to core.
This function only handles the LEVEL1 interrupts. The number of LEVEL1 interrupts is indicated by the feature macro FSL_FEATURE_NUMBER_OF_LEVEL1_INT_VECTORS.
- Parameters:
interrupt – The IRQ to set.
priNum – Priority number set to interrupt controller register.
- Return values:
kStatus_Success – Interrupt priority set successfully
kStatus_Fail – Failed to set the interrupt priority.
-
static inline status_t IRQ_ClearPendingIRQ(IRQn_Type interrupt)
Clear the pending IRQ flag.
Only handle LEVEL1 interrupt. For some devices, there might be multiple interrupt levels. For example, there are NVIC and intmux. Here the interrupts connected to NVIC are the LEVEL1 interrupts, because they are routed to the core directly. The interrupts connected to intmux are the LEVEL2 interrupts, they are routed to NVIC first then routed to core.
This function only handles the LEVEL1 interrupts. The number of LEVEL1 interrupts is indicated by the feature macro FSL_FEATURE_NUMBER_OF_LEVEL1_INT_VECTORS.
- Parameters:
interrupt – The flag which IRQ to clear.
- Return values:
kStatus_Success – Interrupt priority set successfully
kStatus_Fail – Failed to set the interrupt priority.
-
static inline uint32_t DisableGlobalIRQ(void)
Disable the global IRQ.
Disable the global interrupt and return the current primask register. User is required to provided the primask register for the EnableGlobalIRQ().
- Returns:
Current primask value.
-
static inline void EnableGlobalIRQ(uint32_t primask)
Enable the global IRQ.
Set the primask register with the provided primask value but not just enable the primask. The idea is for the convenience of integration of RTOS. some RTOS get its own management mechanism of primask. User is required to use the EnableGlobalIRQ() and DisableGlobalIRQ() in pair.
- Parameters:
primask – value of primask register to be restored. The primask value is supposed to be provided by the DisableGlobalIRQ().
-
static inline bool _SDK_AtomicLocalCompareAndSet(uint32_t *addr, uint32_t expected, uint32_t newValue)
-
static inline uint32_t _SDK_AtomicTestAndSet(uint32_t *addr, uint32_t newValue)
-
FSL_DRIVER_TRANSFER_DOUBLE_WEAK_IRQ
Macro to use the default weak IRQ handler in drivers.
-
MAKE_STATUS(group, code)
Construct a status code value from a group and code number.
-
MAKE_VERSION(major, minor, bugfix)
Construct the version number for drivers.
The driver version is a 32-bit number, for both 32-bit platforms(such as Cortex M) and 16-bit platforms(such as DSC).
| Unused || Major Version || Minor Version || Bug Fix | 31 25 24 17 16 9 8 0
-
ARRAY_SIZE(x)
Computes the number of elements in an array.
-
UINT64_H(X)
Macro to get upper 32 bits of a 64-bit value
-
UINT64_L(X)
Macro to get lower 32 bits of a 64-bit value
-
SUPPRESS_FALL_THROUGH_WARNING()
For switch case code block, if case section ends without “break;” statement, there wil be fallthrough warning with compiler flag -Wextra or -Wimplicit-fallthrough=n when using armgcc. To suppress this warning, “SUPPRESS_FALL_THROUGH_WARNING();” need to be added at the end of each case section which misses “break;”statement.
-
MSDK_REG_SECURE_ADDR(x)
Convert the register address to the one used in secure mode.
-
MSDK_REG_NONSECURE_ADDR(x)
Convert the register address to the one used in non-secure mode.
Lin_lpuart_driver
-
FSL_LIN_LPUART_DRIVER_VERSION
LIN LPUART driver version.
-
enum _lin_lpuart_stop_bit_count
Values:
-
enumerator kLPUART_OneStopBit
One stop bit
-
enumerator kLPUART_TwoStopBit
Two stop bits
-
enumerator kLPUART_OneStopBit
-
enum _lin_lpuart_flags
Values:
-
enumerator kLPUART_TxDataRegEmptyFlag
Transmit data register empty flag, sets when transmit buffer is empty
-
enumerator kLPUART_TransmissionCompleteFlag
Transmission complete flag, sets when transmission activity complete
-
enumerator kLPUART_RxDataRegFullFlag
Receive data register full flag, sets when the receive data buffer is full
-
enumerator kLPUART_IdleLineFlag
Idle line detect flag, sets when idle line detected
-
enumerator kLPUART_RxOverrunFlag
Receive Overrun, sets when new data is received before data is read from receive register
-
enumerator kLPUART_NoiseErrorFlag
Receive takes 3 samples of each received bit. If any of these samples differ, noise flag sets
-
enumerator kLPUART_FramingErrorFlag
Frame error flag, sets if logic 0 was detected where stop bit expected
-
enumerator kLPUART_ParityErrorFlag
If parity enabled, sets upon parity error detection
-
enumerator kLPUART_LinBreakFlag
LIN break detect interrupt flag, sets when LIN break char detected and LIN circuit enabled
-
enumerator kLPUART_RxActiveEdgeFlag
Receive pin active edge interrupt flag, sets when active edge detected
-
enumerator kLPUART_RxActiveFlag
Receiver Active Flag (RAF), sets at beginning of valid start bit
-
enumerator kLPUART_DataMatch1Flag
The next character to be read from LPUART_DATA matches MA1
-
enumerator kLPUART_DataMatch2Flag
The next character to be read from LPUART_DATA matches MA2
-
enumerator kLPUART_NoiseErrorInRxDataRegFlag
NOISY bit, sets if noise detected in current data word
-
enumerator kLPUART_ParityErrorInRxDataRegFlag
PARITY bit, sets if noise detected in current data word
-
enumerator kLPUART_TxFifoEmptyFlag
TXEMPT bit, sets if transmit buffer is empty
-
enumerator kLPUART_RxFifoEmptyFlag
RXEMPT bit, sets if receive buffer is empty
-
enumerator kLPUART_TxFifoOverflowFlag
TXOF bit, sets if transmit buffer overflow occurred
-
enumerator kLPUART_RxFifoUnderflowFlag
RXUF bit, sets if receive buffer underflow occurred
-
enumerator kLPUART_TxDataRegEmptyFlag
-
enum _lin_lpuart_interrupt_enable
Values:
-
enumerator kLPUART_LinBreakInterruptEnable
LIN break detect.
-
enumerator kLPUART_RxActiveEdgeInterruptEnable
Receive Active Edge.
-
enumerator kLPUART_TxDataRegEmptyInterruptEnable
Transmit data register empty.
-
enumerator kLPUART_TransmissionCompleteInterruptEnable
Transmission complete.
-
enumerator kLPUART_RxDataRegFullInterruptEnable
Receiver data register full.
-
enumerator kLPUART_IdleLineInterruptEnable
Idle line.
-
enumerator kLPUART_RxOverrunInterruptEnable
Receiver Overrun.
-
enumerator kLPUART_NoiseErrorInterruptEnable
Noise error flag.
-
enumerator kLPUART_FramingErrorInterruptEnable
Framing error flag.
-
enumerator kLPUART_ParityErrorInterruptEnable
Parity error flag.
-
enumerator kLPUART_TxFifoOverflowInterruptEnable
Transmit FIFO Overflow.
-
enumerator kLPUART_RxFifoUnderflowInterruptEnable
Receive FIFO Underflow.
-
enumerator kLPUART_LinBreakInterruptEnable
-
enum _lin_lpuart_status
Values:
-
enumerator kStatus_LPUART_TxBusy
TX busy
-
enumerator kStatus_LPUART_RxBusy
RX busy
-
enumerator kStatus_LPUART_TxIdle
LPUART transmitter is idle.
-
enumerator kStatus_LPUART_RxIdle
LPUART receiver is idle.
-
enumerator kStatus_LPUART_TxWatermarkTooLarge
TX FIFO watermark too large
-
enumerator kStatus_LPUART_RxWatermarkTooLarge
RX FIFO watermark too large
-
enumerator kStatus_LPUART_FlagCannotClearManually
Some flag can’t manually clear
-
enumerator kStatus_LPUART_Error
Error happens on LPUART.
-
enumerator kStatus_LPUART_RxRingBufferOverrun
LPUART RX software ring buffer overrun.
-
enumerator kStatus_LPUART_RxHardwareOverrun
LPUART RX receiver overrun.
-
enumerator kStatus_LPUART_NoiseError
LPUART noise error.
-
enumerator kStatus_LPUART_FramingError
LPUART framing error.
-
enumerator kStatus_LPUART_ParityError
LPUART parity error.
-
enumerator kStatus_LPUART_TxBusy
-
enum lin_lpuart_bit_count_per_char_t
Values:
-
enumerator LPUART_8_BITS_PER_CHAR
8-bit data characters
-
enumerator LPUART_9_BITS_PER_CHAR
9-bit data characters
-
enumerator LPUART_10_BITS_PER_CHAR
10-bit data characters
-
enumerator LPUART_8_BITS_PER_CHAR
-
typedef enum _lin_lpuart_stop_bit_count lin_lpuart_stop_bit_count_t
-
static inline bool LIN_LPUART_GetRxDataPolarity(const LPUART_Type *base)
-
static inline void LIN_LPUART_SetRxDataPolarity(LPUART_Type *base, bool polarity)
-
static inline void LIN_LPUART_WriteByte(LPUART_Type *base, uint8_t data)
-
static inline void LIN_LPUART_ReadByte(const LPUART_Type *base, uint8_t *readData)
-
status_t LIN_LPUART_CalculateBaudRate(LPUART_Type *base, uint32_t baudRate_Bps, uint32_t srcClock_Hz, uint32_t *osr, uint16_t *sbr)
Calculates the best osr and sbr value for configured baudrate.
- Parameters:
base – LPUART peripheral base address
baudRate_Bps – user configuration structure of type #lin_user_config_t
srcClock_Hz – pointer to the LIN_LPUART driver state structure
osr – pointer to osr value
sbr – pointer to sbr value
- Returns:
An error code or lin_status_t
-
void LIN_LPUART_SetBaudRate(LPUART_Type *base, uint32_t *osr, uint16_t *sbr)
Configure baudrate according to osr and sbr value.
- Parameters:
base – LPUART peripheral base address
osr – pointer to osr value
sbr – pointer to sbr value
-
lin_status_t LIN_LPUART_Init(LPUART_Type *base, lin_user_config_t *linUserConfig, lin_state_t *linCurrentState, uint32_t linSourceClockFreq)
Initializes an LIN_LPUART instance for LIN Network.
The caller provides memory for the driver state structures during initialization. The user must select the LIN_LPUART clock source in the application to initialize the LIN_LPUART. This function initializes a LPUART instance for operation. This function will initialize the run-time state structure to keep track of the on-going transfers, initialize the module to user defined settings and default settings, set break field length to be 13 bit times minimum, enable the break detect interrupt, Rx complete interrupt, frame error detect interrupt, and enable the LPUART module transmitter and receiver
- Parameters:
base – LPUART peripheral base address
linUserConfig – user configuration structure of type #lin_user_config_t
linCurrentState – pointer to the LIN_LPUART driver state structure
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_Deinit(LPUART_Type *base)
Shuts down the LIN_LPUART by disabling interrupts and transmitter/receiver.
- Parameters:
base – LPUART peripheral base address
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_SendFrameDataBlocking(LPUART_Type *base, const uint8_t *txBuff, uint8_t txSize, uint32_t timeoutMSec)
Sends Frame data out through the LIN_LPUART module using blocking method. This function will calculate the checksum byte and send it with the frame data. Blocking means that the function does not return until the transmission is complete.
- Parameters:
base – LPUART peripheral base address
txBuff – source buffer containing 8-bit data chars to send
txSize – the number of bytes to send
timeoutMSec – timeout value in milli seconds
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_SendFrameData(LPUART_Type *base, const uint8_t *txBuff, uint8_t txSize)
Sends frame data out through the LIN_LPUART module using non-blocking method. This enables an a-sync method for transmitting data. Non-blocking means that the function returns immediately. The application has to get the transmit status to know when the transmit is complete. This function will calculate the checksum byte and send it with the frame data.
- Parameters:
base – LPUART peripheral base address
txBuff – source buffer containing 8-bit data chars to send
txSize – the number of bytes to send
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_GetTransmitStatus(LPUART_Type *base, uint8_t *bytesRemaining)
Get status of an on-going non-blocking transmission While sending frame data using non-blocking method, users can use this function to get status of that transmission. This function return LIN_TX_BUSY while sending, or LIN_TIMEOUT if timeout has occurred, or return LIN_SUCCESS when the transmission is complete. The bytesRemaining shows number of bytes that still needed to transmit.
- Parameters:
base – LPUART peripheral base address
bytesRemaining – Number of bytes still needed to transmit
- Returns:
lin_status_t LIN_TX_BUSY, LIN_SUCCESS or LIN_TIMEOUT
-
lin_status_t LIN_LPUART_RecvFrmDataBlocking(LPUART_Type *base, uint8_t *rxBuff, uint8_t rxSize, uint32_t timeoutMSec)
Receives frame data through the LIN_LPUART module using blocking method. This function will check the checksum byte. If the checksum is correct, it will receive the frame data. Blocking means that the function does not return until the reception is complete.
- Parameters:
base – LPUART peripheral base address
rxBuff – buffer containing 8-bit received data
rxSize – the number of bytes to receive
timeoutMSec – timeout value in milli seconds
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_RecvFrmData(LPUART_Type *base, uint8_t *rxBuff, uint8_t rxSize)
Receives frame data through the LIN_LPUART module using non-blocking method. This function will check the checksum byte. If the checksum is correct, it will receive it with the frame data. Non-blocking means that the function returns immediately. The application has to get the receive status to know when the reception is complete.
- Parameters:
base – LPUART peripheral base address
rxBuff – buffer containing 8-bit received data
rxSize – the number of bytes to receive
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_AbortTransferData(LPUART_Type *base)
Aborts an on-going non-blocking transmission/reception. While performing a non-blocking transferring data, users can call this function to terminate immediately the transferring.
- Parameters:
base – LPUART peripheral base address
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_GetReceiveStatus(LPUART_Type *base, uint8_t *bytesRemaining)
Get status of an on-going non-blocking reception While receiving frame data using non-blocking method, users can use this function to get status of that receiving. This function return the current event ID, LIN_RX_BUSY while receiving and return LIN_SUCCESS, or timeout (LIN_TIMEOUT) when the reception is complete. The bytesRemaining shows number of bytes that still needed to receive.
- Parameters:
base – LPUART peripheral base address
bytesRemaining – Number of bytes still needed to receive
- Returns:
lin_status_t LIN_RX_BUSY, LIN_TIMEOUT or LIN_SUCCESS
-
lin_status_t LIN_LPUART_GoToSleepMode(LPUART_Type *base)
This function puts current node to sleep mode This function changes current node state to LIN_NODE_STATE_SLEEP_MODE.
- Parameters:
base – LPUART peripheral base address
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_GotoIdleState(LPUART_Type *base)
Puts current LIN node to Idle state This function changes current node state to LIN_NODE_STATE_IDLE.
- Parameters:
base – LPUART peripheral base address
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_SendWakeupSignal(LPUART_Type *base)
Sends a wakeup signal through the LIN_LPUART interface.
- Parameters:
base – LPUART peripheral base address
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_MasterSendHeader(LPUART_Type *base, uint8_t id)
Sends frame header out through the LIN_LPUART module using a non-blocking method. This function sends LIN Break field, sync field then the ID with correct parity.
- Parameters:
base – LPUART peripheral base address
id – Frame Identifier
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_EnableIRQ(LPUART_Type *base)
Enables LIN_LPUART hardware interrupts.
- Parameters:
base – LPUART peripheral base address
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_DisableIRQ(LPUART_Type *base)
Disables LIN_LPUART hardware interrupts.
- Parameters:
base – LPUART peripheral base address
- Returns:
An error code or lin_status_t
-
lin_status_t LIN_LPUART_AutoBaudCapture(uint32_t instance)
This function capture bits time to detect break char, calculate baudrate from sync bits and enable transceiver if autobaud successful. This function should only be used in Slave. The timer should be in mode input capture of both rising and falling edges. The timer input capture pin should be externally connected to RXD pin.
- Parameters:
instance – LPUART instance
- Returns:
lin_status_t
-
void LIN_LPUART_IRQHandler(LPUART_Type *base)
LIN_LPUART RX TX interrupt handler.
- Parameters:
base – LPUART peripheral base address
- Returns:
void
-
AUTOBAUD_BAUDRATE_TOLERANCE
-
BIT_RATE_TOLERANCE_UNSYNC
-
BIT_DURATION_MAX_19200
-
BIT_DURATION_MIN_19200
-
BIT_DURATION_MAX_14400
-
BIT_DURATION_MIN_14400
-
BIT_DURATION_MAX_9600
-
BIT_DURATION_MIN_9600
-
BIT_DURATION_MAX_4800
-
BIT_DURATION_MIN_4800
-
BIT_DURATION_MAX_2400
-
BIT_DURATION_MIN_2400
-
TWO_BIT_DURATION_MAX_19200
-
TWO_BIT_DURATION_MIN_19200
-
TWO_BIT_DURATION_MAX_14400
-
TWO_BIT_DURATION_MIN_14400
-
TWO_BIT_DURATION_MAX_9600
-
TWO_BIT_DURATION_MIN_9600
-
TWO_BIT_DURATION_MAX_4800
-
TWO_BIT_DURATION_MIN_4800
-
TWO_BIT_DURATION_MAX_2400
-
TWO_BIT_DURATION_MIN_2400
-
AUTOBAUD_BREAK_TIME_MIN
LPI2C: Low Power Inter-Integrated Circuit Driver
-
FSL_LPI2C_DRIVER_VERSION
LPI2C driver version.
LPI2C status return codes.
Values:
-
enumerator kStatus_LPI2C_Busy
The master is already performing a transfer.
-
enumerator kStatus_LPI2C_Idle
The slave driver is idle.
-
enumerator kStatus_LPI2C_Nak
The slave device sent a NAK in response to a byte.
-
enumerator kStatus_LPI2C_FifoError
FIFO under run or overrun.
-
enumerator kStatus_LPI2C_BitError
Transferred bit was not seen on the bus.
-
enumerator kStatus_LPI2C_ArbitrationLost
Arbitration lost error.
-
enumerator kStatus_LPI2C_PinLowTimeout
SCL or SDA were held low longer than the timeout.
-
enumerator kStatus_LPI2C_NoTransferInProgress
Attempt to abort a transfer when one is not in progress.
-
enumerator kStatus_LPI2C_DmaRequestFail
DMA request failed.
-
enumerator kStatus_LPI2C_Timeout
Timeout polling status flags.
-
enumerator kStatus_LPI2C_Busy
-
IRQn_Type const kLpi2cIrqs[]
Array to map LPI2C instance number to IRQ number, used internally for LPI2C master interrupt and EDMA transactional APIs.
-
lpi2c_master_isr_t s_lpi2cMasterIsr
Pointer to master IRQ handler for each instance, used internally for LPI2C master interrupt and EDMA transactional APIs.
-
void *s_lpi2cMasterHandle[]
Pointers to master handles for each instance, used internally for LPI2C master interrupt and EDMA transactional APIs.
-
uint32_t LPI2C_GetInstance(LPI2C_Type *base)
Returns an instance number given a base address.
If an invalid base address is passed, debug builds will assert. Release builds will just return instance number 0.
- Parameters:
base – The LPI2C peripheral base address.
- Returns:
LPI2C instance number starting from 0.
-
I2C_RETRY_TIMES
Retry times for waiting flag.
LPI2C Master Driver
-
void LPI2C_MasterGetDefaultConfig(lpi2c_master_config_t *masterConfig)
Provides a default configuration for the LPI2C master peripheral.
This function provides the following default configuration for the LPI2C master peripheral:
masterConfig->enableMaster = true; masterConfig->debugEnable = false; masterConfig->ignoreAck = false; masterConfig->pinConfig = kLPI2C_2PinOpenDrain; masterConfig->baudRate_Hz = 100000U; masterConfig->busIdleTimeout_ns = 0; masterConfig->pinLowTimeout_ns = 0; masterConfig->sdaGlitchFilterWidth_ns = 0; masterConfig->sclGlitchFilterWidth_ns = 0; masterConfig->hostRequest.enable = false; masterConfig->hostRequest.source = kLPI2C_HostRequestExternalPin; masterConfig->hostRequest.polarity = kLPI2C_HostRequestPinActiveHigh;
After calling this function, you can override any settings in order to customize the configuration, prior to initializing the master driver with LPI2C_MasterInit().
- Parameters:
masterConfig – [out] User provided configuration structure for default values. Refer to lpi2c_master_config_t.
-
void LPI2C_MasterInit(LPI2C_Type *base, const lpi2c_master_config_t *masterConfig, uint32_t sourceClock_Hz)
Initializes the LPI2C master peripheral.
This function enables the peripheral clock and initializes the LPI2C master peripheral as described by the user provided configuration. A software reset is performed prior to configuration.
- Parameters:
base – The LPI2C peripheral base address.
masterConfig – User provided peripheral configuration. Use LPI2C_MasterGetDefaultConfig() to get a set of defaults that you can override.
sourceClock_Hz – Frequency in Hertz of the LPI2C functional clock. Used to calculate the baud rate divisors, filter widths, and timeout periods.
-
void LPI2C_MasterDeinit(LPI2C_Type *base)
Deinitializes the LPI2C master peripheral.
This function disables the LPI2C master peripheral and gates the clock. It also performs a software reset to restore the peripheral to reset conditions.
- Parameters:
base – The LPI2C peripheral base address.
-
void LPI2C_MasterConfigureDataMatch(LPI2C_Type *base, const lpi2c_data_match_config_t *matchConfig)
Configures LPI2C master data match feature.
- Parameters:
base – The LPI2C peripheral base address.
matchConfig – Settings for the data match feature.
-
status_t LPI2C_MasterCheckAndClearError(LPI2C_Type *base, uint32_t status)
Convert provided flags to status code, and clear any errors if present.
- Parameters:
base – The LPI2C peripheral base address.
status – Current status flags value that will be checked.
- Return values:
kStatus_Success –
kStatus_LPI2C_PinLowTimeout –
kStatus_LPI2C_ArbitrationLost –
kStatus_LPI2C_Nak –
kStatus_LPI2C_FifoError –
-
status_t LPI2C_CheckForBusyBus(LPI2C_Type *base)
Make sure the bus isn’t already busy.
A busy bus is allowed if we are the one driving it.
- Parameters:
base – The LPI2C peripheral base address.
- Return values:
kStatus_Success –
kStatus_LPI2C_Busy –
-
static inline void LPI2C_MasterReset(LPI2C_Type *base)
Performs a software reset.
Restores the LPI2C master peripheral to reset conditions.
- Parameters:
base – The LPI2C peripheral base address.
-
static inline void LPI2C_MasterEnable(LPI2C_Type *base, bool enable)
Enables or disables the LPI2C module as master.
- Parameters:
base – The LPI2C peripheral base address.
enable – Pass true to enable or false to disable the specified LPI2C as master.
-
static inline uint32_t LPI2C_MasterGetStatusFlags(LPI2C_Type *base)
Gets the LPI2C master status flags.
A bit mask with the state of all LPI2C master status flags is returned. For each flag, the corresponding bit in the return value is set if the flag is asserted.
See also
_lpi2c_master_flags
- Parameters:
base – The LPI2C peripheral base address.
- Returns:
State of the status flags:
1: related status flag is set.
0: related status flag is not set.
-
static inline void LPI2C_MasterClearStatusFlags(LPI2C_Type *base, uint32_t statusMask)
Clears the LPI2C master status flag state.
The following status register flags can be cleared:
kLPI2C_MasterEndOfPacketFlag
kLPI2C_MasterStopDetectFlag
kLPI2C_MasterNackDetectFlag
kLPI2C_MasterArbitrationLostFlag
kLPI2C_MasterFifoErrFlag
kLPI2C_MasterPinLowTimeoutFlag
kLPI2C_MasterDataMatchFlag
Attempts to clear other flags has no effect.
See also
_lpi2c_master_flags.
- Parameters:
base – The LPI2C peripheral base address.
statusMask – A bitmask of status flags that are to be cleared. The mask is composed of _lpi2c_master_flags enumerators OR’d together. You may pass the result of a previous call to LPI2C_MasterGetStatusFlags().
-
static inline void LPI2C_MasterEnableInterrupts(LPI2C_Type *base, uint32_t interruptMask)
Enables the LPI2C master interrupt requests.
All flags except kLPI2C_MasterBusyFlag and kLPI2C_MasterBusBusyFlag can be enabled as interrupts.
- Parameters:
base – The LPI2C peripheral base address.
interruptMask – Bit mask of interrupts to enable. See _lpi2c_master_flags for the set of constants that should be OR’d together to form the bit mask.
-
static inline void LPI2C_MasterDisableInterrupts(LPI2C_Type *base, uint32_t interruptMask)
Disables the LPI2C master interrupt requests.
All flags except kLPI2C_MasterBusyFlag and kLPI2C_MasterBusBusyFlag can be enabled as interrupts.
- Parameters:
base – The LPI2C peripheral base address.
interruptMask – Bit mask of interrupts to disable. See _lpi2c_master_flags for the set of constants that should be OR’d together to form the bit mask.
-
static inline uint32_t LPI2C_MasterGetEnabledInterrupts(LPI2C_Type *base)
Returns the set of currently enabled LPI2C master interrupt requests.
- Parameters:
base – The LPI2C peripheral base address.
- Returns:
A bitmask composed of _lpi2c_master_flags enumerators OR’d together to indicate the set of enabled interrupts.
-
static inline void LPI2C_MasterEnableDMA(LPI2C_Type *base, bool enableTx, bool enableRx)
Enables or disables LPI2C master DMA requests.
- Parameters:
base – The LPI2C peripheral base address.
enableTx – Enable flag for transmit DMA request. Pass true for enable, false for disable.
enableRx – Enable flag for receive DMA request. Pass true for enable, false for disable.
-
static inline uint32_t LPI2C_MasterGetTxFifoAddress(LPI2C_Type *base)
Gets LPI2C master transmit data register address for DMA transfer.
- Parameters:
base – The LPI2C peripheral base address.
- Returns:
The LPI2C Master Transmit Data Register address.
-
static inline uint32_t LPI2C_MasterGetRxFifoAddress(LPI2C_Type *base)
Gets LPI2C master receive data register address for DMA transfer.
- Parameters:
base – The LPI2C peripheral base address.
- Returns:
The LPI2C Master Receive Data Register address.
-
static inline void LPI2C_MasterSetWatermarks(LPI2C_Type *base, size_t txWords, size_t rxWords)
Sets the watermarks for LPI2C master FIFOs.
- Parameters:
base – The LPI2C peripheral base address.
txWords – Transmit FIFO watermark value in words. The kLPI2C_MasterTxReadyFlag flag is set whenever the number of words in the transmit FIFO is equal or less than txWords. Writing a value equal or greater than the FIFO size is truncated.
rxWords – Receive FIFO watermark value in words. The kLPI2C_MasterRxReadyFlag flag is set whenever the number of words in the receive FIFO is greater than rxWords. Writing a value equal or greater than the FIFO size is truncated.
-
static inline void LPI2C_MasterGetFifoCounts(LPI2C_Type *base, size_t *rxCount, size_t *txCount)
Gets the current number of words in the LPI2C master FIFOs.
- Parameters:
base – The LPI2C peripheral base address.
txCount – [out] Pointer through which the current number of words in the transmit FIFO is returned. Pass NULL if this value is not required.
rxCount – [out] Pointer through which the current number of words in the receive FIFO is returned. Pass NULL if this value is not required.
-
void LPI2C_MasterSetBaudRate(LPI2C_Type *base, uint32_t sourceClock_Hz, uint32_t baudRate_Hz)
Sets the I2C bus frequency for master transactions.
The LPI2C master is automatically disabled and re-enabled as necessary to configure the baud rate. Do not call this function during a transfer, or the transfer is aborted.
Note
Please note that the second parameter is the clock frequency of LPI2C module, the third parameter means user configured bus baudrate, this implementation is different from other I2C drivers which use baudrate configuration as second parameter and source clock frequency as third parameter.
- Parameters:
base – The LPI2C peripheral base address.
sourceClock_Hz – LPI2C functional clock frequency in Hertz.
baudRate_Hz – Requested bus frequency in Hertz.
-
static inline bool LPI2C_MasterGetBusIdleState(LPI2C_Type *base)
Returns whether the bus is idle.
Requires the master mode to be enabled.
- Parameters:
base – The LPI2C peripheral base address.
- Return values:
true – Bus is busy.
false – Bus is idle.
-
status_t LPI2C_MasterStart(LPI2C_Type *base, uint8_t address, lpi2c_direction_t dir)
Sends a START signal and slave address on the I2C bus.
This function is used to initiate a new master mode transfer. First, the bus state is checked to ensure that another master is not occupying the bus. Then a START signal is transmitted, followed by the 7-bit address specified in the address parameter. Note that this function does not actually wait until the START and address are successfully sent on the bus before returning.
- Parameters:
base – The LPI2C peripheral base address.
address – 7-bit slave device address, in bits [6:0].
dir – Master transfer direction, either kLPI2C_Read or kLPI2C_Write. This parameter is used to set the R/w bit (bit 0) in the transmitted slave address.
- Return values:
kStatus_Success – START signal and address were successfully enqueued in the transmit FIFO.
kStatus_LPI2C_Busy – Another master is currently utilizing the bus.
-
static inline status_t LPI2C_MasterRepeatedStart(LPI2C_Type *base, uint8_t address, lpi2c_direction_t dir)
Sends a repeated START signal and slave address on the I2C bus.
This function is used to send a Repeated START signal when a transfer is already in progress. Like LPI2C_MasterStart(), it also sends the specified 7-bit address.
Note
This function exists primarily to maintain compatible APIs between LPI2C and I2C drivers, as well as to better document the intent of code that uses these APIs.
- Parameters:
base – The LPI2C peripheral base address.
address – 7-bit slave device address, in bits [6:0].
dir – Master transfer direction, either kLPI2C_Read or kLPI2C_Write. This parameter is used to set the R/w bit (bit 0) in the transmitted slave address.
- Return values:
kStatus_Success – Repeated START signal and address were successfully enqueued in the transmit FIFO.
kStatus_LPI2C_Busy – Another master is currently utilizing the bus.
-
status_t LPI2C_MasterSend(LPI2C_Type *base, void *txBuff, size_t txSize)
Performs a polling send transfer on the I2C bus.
Sends up to txSize number of bytes to the previously addressed slave device. The slave may reply with a NAK to any byte in order to terminate the transfer early. If this happens, this function returns kStatus_LPI2C_Nak.
- Parameters:
base – The LPI2C peripheral base address.
txBuff – The pointer to the data to be transferred.
txSize – The length in bytes of the data to be transferred.
- Return values:
kStatus_Success – Data was sent successfully.
kStatus_LPI2C_Busy – Another master is currently utilizing the bus.
kStatus_LPI2C_Nak – The slave device sent a NAK in response to a byte.
kStatus_LPI2C_FifoError – FIFO under run or over run.
kStatus_LPI2C_ArbitrationLost – Arbitration lost error.
kStatus_LPI2C_PinLowTimeout – SCL or SDA were held low longer than the timeout.
-
status_t LPI2C_MasterReceive(LPI2C_Type *base, void *rxBuff, size_t rxSize)
Performs a polling receive transfer on the I2C bus.
- Parameters:
base – The LPI2C peripheral base address.
rxBuff – The pointer to the data to be transferred.
rxSize – The length in bytes of the data to be transferred.
- Return values:
kStatus_Success – Data was received successfully.
kStatus_LPI2C_Busy – Another master is currently utilizing the bus.
kStatus_LPI2C_Nak – The slave device sent a NAK in response to a byte.
kStatus_LPI2C_FifoError – FIFO under run or overrun.
kStatus_LPI2C_ArbitrationLost – Arbitration lost error.
kStatus_LPI2C_PinLowTimeout – SCL or SDA were held low longer than the timeout.
-
status_t LPI2C_MasterStop(LPI2C_Type *base)
Sends a STOP signal on the I2C bus.
This function does not return until the STOP signal is seen on the bus, or an error occurs.
- Parameters:
base – The LPI2C peripheral base address.
- Return values:
kStatus_Success – The STOP signal was successfully sent on the bus and the transaction terminated.
kStatus_LPI2C_Busy – Another master is currently utilizing the bus.
kStatus_LPI2C_Nak – The slave device sent a NAK in response to a byte.
kStatus_LPI2C_FifoError – FIFO under run or overrun.
kStatus_LPI2C_ArbitrationLost – Arbitration lost error.
kStatus_LPI2C_PinLowTimeout – SCL or SDA were held low longer than the timeout.
-
status_t LPI2C_MasterTransferBlocking(LPI2C_Type *base, lpi2c_master_transfer_t *transfer)
Performs a master polling transfer on the I2C bus.
Note
The API does not return until the transfer succeeds or fails due to error happens during transfer.
- Parameters:
base – The LPI2C peripheral base address.
transfer – Pointer to the transfer structure.
- Return values:
kStatus_Success – Data was received successfully.
kStatus_LPI2C_Busy – Another master is currently utilizing the bus.
kStatus_LPI2C_Nak – The slave device sent a NAK in response to a byte.
kStatus_LPI2C_FifoError – FIFO under run or overrun.
kStatus_LPI2C_ArbitrationLost – Arbitration lost error.
kStatus_LPI2C_PinLowTimeout – SCL or SDA were held low longer than the timeout.
-
void LPI2C_MasterTransferCreateHandle(LPI2C_Type *base, lpi2c_master_handle_t *handle, lpi2c_master_transfer_callback_t callback, void *userData)
Creates a new handle for the LPI2C master non-blocking APIs.
The creation of a handle is for use with the non-blocking APIs. Once a handle is created, there is not a corresponding destroy handle. If the user wants to terminate a transfer, the LPI2C_MasterTransferAbort() API shall be called.
Note
The function also enables the NVIC IRQ for the input LPI2C. Need to notice that on some SoCs the LPI2C IRQ is connected to INTMUX, in this case user needs to enable the associated INTMUX IRQ in application.
- Parameters:
base – The LPI2C peripheral base address.
handle – [out] Pointer to the LPI2C master driver handle.
callback – User provided pointer to the asynchronous callback function.
userData – User provided pointer to the application callback data.
-
status_t LPI2C_MasterTransferNonBlocking(LPI2C_Type *base, lpi2c_master_handle_t *handle, lpi2c_master_transfer_t *transfer)
Performs a non-blocking transaction on the I2C bus.
- Parameters:
base – The LPI2C peripheral base address.
handle – Pointer to the LPI2C master driver handle.
transfer – The pointer to the transfer descriptor.
- Return values:
kStatus_Success – The transaction was started successfully.
kStatus_LPI2C_Busy – Either another master is currently utilizing the bus, or a non-blocking transaction is already in progress.
-
status_t LPI2C_MasterTransferGetCount(LPI2C_Type *base, lpi2c_master_handle_t *handle, size_t *count)
Returns number of bytes transferred so far.
- Parameters:
base – The LPI2C peripheral base address.
handle – Pointer to the LPI2C master driver handle.
count – [out] Number of bytes transferred so far by the non-blocking transaction.
- Return values:
kStatus_Success –
kStatus_NoTransferInProgress – There is not a non-blocking transaction currently in progress.
-
void LPI2C_MasterTransferAbort(LPI2C_Type *base, lpi2c_master_handle_t *handle)
Terminates a non-blocking LPI2C master transmission early.
Note
It is not safe to call this function from an IRQ handler that has a higher priority than the LPI2C peripheral’s IRQ priority.
- Parameters:
base – The LPI2C peripheral base address.
handle – Pointer to the LPI2C master driver handle.
-
void LPI2C_MasterTransferHandleIRQ(LPI2C_Type *base, void *lpi2cMasterHandle)
Reusable routine to handle master interrupts.
Note
This function does not need to be called unless you are reimplementing the nonblocking API’s interrupt handler routines to add special functionality.
- Parameters:
base – The LPI2C peripheral base address.
lpi2cMasterHandle – Pointer to the LPI2C master driver handle.
-
enum _lpi2c_master_flags
LPI2C master peripheral flags.
The following status register flags can be cleared:
kLPI2C_MasterEndOfPacketFlag
kLPI2C_MasterStopDetectFlag
kLPI2C_MasterNackDetectFlag
kLPI2C_MasterArbitrationLostFlag
kLPI2C_MasterFifoErrFlag
kLPI2C_MasterPinLowTimeoutFlag
kLPI2C_MasterDataMatchFlag
All flags except kLPI2C_MasterBusyFlag and kLPI2C_MasterBusBusyFlag can be enabled as interrupts.
Note
These enums are meant to be OR’d together to form a bit mask.
Values:
-
enumerator kLPI2C_MasterTxReadyFlag
Transmit data flag
-
enumerator kLPI2C_MasterRxReadyFlag
Receive data flag
-
enumerator kLPI2C_MasterEndOfPacketFlag
End Packet flag
-
enumerator kLPI2C_MasterStopDetectFlag
Stop detect flag
-
enumerator kLPI2C_MasterNackDetectFlag
NACK detect flag
-
enumerator kLPI2C_MasterArbitrationLostFlag
Arbitration lost flag
-
enumerator kLPI2C_MasterFifoErrFlag
FIFO error flag
-
enumerator kLPI2C_MasterPinLowTimeoutFlag
Pin low timeout flag
-
enumerator kLPI2C_MasterDataMatchFlag
Data match flag
-
enumerator kLPI2C_MasterBusyFlag
Master busy flag
-
enumerator kLPI2C_MasterBusBusyFlag
Bus busy flag
-
enumerator kLPI2C_MasterClearFlags
All flags which are cleared by the driver upon starting a transfer.
-
enumerator kLPI2C_MasterIrqFlags
IRQ sources enabled by the non-blocking transactional API.
-
enumerator kLPI2C_MasterErrorFlags
Errors to check for.
-
enum _lpi2c_direction
Direction of master and slave transfers.
Values:
-
enumerator kLPI2C_Write
Master transmit.
-
enumerator kLPI2C_Read
Master receive.
-
enumerator kLPI2C_Write
-
enum _lpi2c_master_pin_config
LPI2C pin configuration.
Values:
-
enumerator kLPI2C_2PinOpenDrain
LPI2C Configured for 2-pin open drain mode
-
enumerator kLPI2C_2PinOutputOnly
LPI2C Configured for 2-pin output only mode (ultra-fast mode)
-
enumerator kLPI2C_2PinPushPull
LPI2C Configured for 2-pin push-pull mode
-
enumerator kLPI2C_4PinPushPull
LPI2C Configured for 4-pin push-pull mode
-
enumerator kLPI2C_2PinOpenDrainWithSeparateSlave
LPI2C Configured for 2-pin open drain mode with separate LPI2C slave
-
enumerator kLPI2C_2PinOutputOnlyWithSeparateSlave
LPI2C Configured for 2-pin output only mode(ultra-fast mode) with separate LPI2C slave
-
enumerator kLPI2C_2PinPushPullWithSeparateSlave
LPI2C Configured for 2-pin push-pull mode with separate LPI2C slave
-
enumerator kLPI2C_4PinPushPullWithInvertedOutput
LPI2C Configured for 4-pin push-pull mode(inverted outputs)
-
enumerator kLPI2C_2PinOpenDrain
-
enum _lpi2c_host_request_source
LPI2C master host request selection.
Values:
-
enumerator kLPI2C_HostRequestExternalPin
Select the LPI2C_HREQ pin as the host request input
-
enumerator kLPI2C_HostRequestInputTrigger
Select the input trigger as the host request input
-
enumerator kLPI2C_HostRequestExternalPin
-
enum _lpi2c_host_request_polarity
LPI2C master host request pin polarity configuration.
Values:
-
enumerator kLPI2C_HostRequestPinActiveLow
Configure the LPI2C_HREQ pin active low
-
enumerator kLPI2C_HostRequestPinActiveHigh
Configure the LPI2C_HREQ pin active high
-
enumerator kLPI2C_HostRequestPinActiveLow
-
enum _lpi2c_data_match_config_mode
LPI2C master data match configuration modes.
Values:
-
enumerator kLPI2C_MatchDisabled
LPI2C Match Disabled
-
enumerator kLPI2C_1stWordEqualsM0OrM1
LPI2C Match Enabled and 1st data word equals MATCH0 OR MATCH1
-
enumerator kLPI2C_AnyWordEqualsM0OrM1
LPI2C Match Enabled and any data word equals MATCH0 OR MATCH1
-
enumerator kLPI2C_1stWordEqualsM0And2ndWordEqualsM1
LPI2C Match Enabled and 1st data word equals MATCH0, 2nd data equals MATCH1
-
enumerator kLPI2C_AnyWordEqualsM0AndNextWordEqualsM1
LPI2C Match Enabled and any data word equals MATCH0, next data equals MATCH1
-
enumerator kLPI2C_1stWordAndM1EqualsM0AndM1
LPI2C Match Enabled and 1st data word and MATCH0 equals MATCH0 and MATCH1
-
enumerator kLPI2C_AnyWordAndM1EqualsM0AndM1
LPI2C Match Enabled and any data word and MATCH0 equals MATCH0 and MATCH1
-
enumerator kLPI2C_MatchDisabled
-
enum _lpi2c_master_transfer_flags
Transfer option flags.
Note
These enumerations are intended to be OR’d together to form a bit mask of options for the _lpi2c_master_transfer::flags field.
Values:
-
enumerator kLPI2C_TransferDefaultFlag
Transfer starts with a start signal, stops with a stop signal.
-
enumerator kLPI2C_TransferNoStartFlag
Don’t send a start condition, address, and sub address
-
enumerator kLPI2C_TransferRepeatedStartFlag
Send a repeated start condition
-
enumerator kLPI2C_TransferNoStopFlag
Don’t send a stop condition.
-
enumerator kLPI2C_TransferDefaultFlag
-
typedef enum _lpi2c_direction lpi2c_direction_t
Direction of master and slave transfers.
-
typedef enum _lpi2c_master_pin_config lpi2c_master_pin_config_t
LPI2C pin configuration.
-
typedef enum _lpi2c_host_request_source lpi2c_host_request_source_t
LPI2C master host request selection.
-
typedef enum _lpi2c_host_request_polarity lpi2c_host_request_polarity_t
LPI2C master host request pin polarity configuration.
-
typedef struct _lpi2c_master_config lpi2c_master_config_t
Structure with settings to initialize the LPI2C master module.
This structure holds configuration settings for the LPI2C peripheral. To initialize this structure to reasonable defaults, call the LPI2C_MasterGetDefaultConfig() function and pass a pointer to your configuration structure instance.
The configuration structure can be made constant so it resides in flash.
-
typedef enum _lpi2c_data_match_config_mode lpi2c_data_match_config_mode_t
LPI2C master data match configuration modes.
-
typedef struct _lpi2c_match_config lpi2c_data_match_config_t
LPI2C master data match configuration structure.
-
typedef struct _lpi2c_master_transfer lpi2c_master_transfer_t
LPI2C master descriptor of the transfer.
-
typedef struct _lpi2c_master_handle lpi2c_master_handle_t
LPI2C master handle of the transfer.
-
typedef void (*lpi2c_master_transfer_callback_t)(LPI2C_Type *base, lpi2c_master_handle_t *handle, status_t completionStatus, void *userData)
Master completion callback function pointer type.
This callback is used only for the non-blocking master transfer API. Specify the callback you wish to use in the call to LPI2C_MasterTransferCreateHandle().
- Param base:
The LPI2C peripheral base address.
- Param handle:
Pointer to the LPI2C master driver handle.
- Param completionStatus:
Either kStatus_Success or an error code describing how the transfer completed.
- Param userData:
Arbitrary pointer-sized value passed from the application.
-
typedef void (*lpi2c_master_isr_t)(LPI2C_Type *base, void *handle)
Typedef for master interrupt handler, used internally for LPI2C master interrupt and EDMA transactional APIs.
-
struct _lpi2c_master_config
- #include <fsl_lpi2c.h>
Structure with settings to initialize the LPI2C master module.
This structure holds configuration settings for the LPI2C peripheral. To initialize this structure to reasonable defaults, call the LPI2C_MasterGetDefaultConfig() function and pass a pointer to your configuration structure instance.
The configuration structure can be made constant so it resides in flash.
Public Members
-
bool enableMaster
Whether to enable master mode.
-
bool enableDoze
Whether master is enabled in doze mode.
-
bool debugEnable
Enable transfers to continue when halted in debug mode.
-
bool ignoreAck
Whether to ignore ACK/NACK.
-
lpi2c_master_pin_config_t pinConfig
The pin configuration option.
-
uint32_t baudRate_Hz
Desired baud rate in Hertz.
-
uint32_t busIdleTimeout_ns
Bus idle timeout in nanoseconds. Set to 0 to disable.
-
uint32_t pinLowTimeout_ns
Pin low timeout in nanoseconds. Set to 0 to disable.
-
uint8_t sdaGlitchFilterWidth_ns
Width in nanoseconds of glitch filter on SDA pin. Set to 0 to disable.
-
uint8_t sclGlitchFilterWidth_ns
Width in nanoseconds of glitch filter on SCL pin. Set to 0 to disable.
-
struct _lpi2c_master_config hostRequest
Host request options.
-
bool enableMaster
-
struct _lpi2c_match_config
- #include <fsl_lpi2c.h>
LPI2C master data match configuration structure.
Public Members
-
lpi2c_data_match_config_mode_t matchMode
Data match configuration setting.
-
bool rxDataMatchOnly
When set to true, received data is ignored until a successful match.
-
uint32_t match0
Match value 0.
-
uint32_t match1
Match value 1.
-
lpi2c_data_match_config_mode_t matchMode
-
struct _lpi2c_master_transfer
- #include <fsl_lpi2c.h>
Non-blocking transfer descriptor structure.
This structure is used to pass transaction parameters to the LPI2C_MasterTransferNonBlocking() API.
Public Members
-
uint32_t flags
Bit mask of options for the transfer. See enumeration _lpi2c_master_transfer_flags for available options. Set to 0 or kLPI2C_TransferDefaultFlag for normal transfers.
-
uint16_t slaveAddress
The 7-bit slave address.
-
lpi2c_direction_t direction
Either kLPI2C_Read or kLPI2C_Write.
-
uint32_t subaddress
Sub address. Transferred MSB first.
-
size_t subaddressSize
Length of sub address to send in bytes. Maximum size is 4 bytes.
-
void *data
Pointer to data to transfer.
-
size_t dataSize
Number of bytes to transfer.
-
uint32_t flags
-
struct _lpi2c_master_handle
- #include <fsl_lpi2c.h>
Driver handle for master non-blocking APIs.
Note
The contents of this structure are private and subject to change.
Public Members
-
uint8_t state
Transfer state machine current state.
-
uint16_t remainingBytes
Remaining byte count in current state.
-
uint8_t *buf
Buffer pointer for current state.
-
uint16_t commandBuffer[6]
LPI2C command sequence. When all 6 command words are used: Start&addr&write[1 word] + subaddr[4 words] + restart&addr&read[1 word]
-
lpi2c_master_transfer_t transfer
Copy of the current transfer info.
-
lpi2c_master_transfer_callback_t completionCallback
Callback function pointer.
-
void *userData
Application data passed to callback.
-
uint8_t state
-
struct hostRequest
Public Members
-
bool enable
Enable host request.
-
lpi2c_host_request_source_t source
Host request source.
-
lpi2c_host_request_polarity_t polarity
Host request pin polarity.
-
bool enable
LPI2C Master DMA Driver
-
void LPI2C_MasterCreateEDMAHandle(LPI2C_Type *base, lpi2c_master_edma_handle_t *handle, edma_handle_t *rxDmaHandle, edma_handle_t *txDmaHandle, lpi2c_master_edma_transfer_callback_t callback, void *userData)
Create a new handle for the LPI2C master DMA APIs.
The creation of a handle is for use with the DMA APIs. Once a handle is created, there is not a corresponding destroy handle. If the user wants to terminate a transfer, the LPI2C_MasterTransferAbortEDMA() API shall be called.
For devices where the LPI2C send and receive DMA requests are OR’d together, the txDmaHandle parameter is ignored and may be set to NULL.
- Parameters:
base – The LPI2C peripheral base address.
handle – [out] Pointer to the LPI2C master driver handle.
rxDmaHandle – Handle for the eDMA receive channel. Created by the user prior to calling this function.
txDmaHandle – Handle for the eDMA transmit channel. Created by the user prior to calling this function.
callback – User provided pointer to the asynchronous callback function.
userData – User provided pointer to the application callback data.
-
status_t LPI2C_MasterTransferEDMA(LPI2C_Type *base, lpi2c_master_edma_handle_t *handle, lpi2c_master_transfer_t *transfer)
Performs a non-blocking DMA-based transaction on the I2C bus.
The callback specified when the handle was created is invoked when the transaction has completed.
- Parameters:
base – The LPI2C peripheral base address.
handle – Pointer to the LPI2C master driver handle.
transfer – The pointer to the transfer descriptor.
- Return values:
kStatus_Success – The transaction was started successfully.
kStatus_LPI2C_Busy – Either another master is currently utilizing the bus, or another DMA transaction is already in progress.
-
status_t LPI2C_MasterTransferGetCountEDMA(LPI2C_Type *base, lpi2c_master_edma_handle_t *handle, size_t *count)
Returns number of bytes transferred so far.
- Parameters:
base – The LPI2C peripheral base address.
handle – Pointer to the LPI2C master driver handle.
count – [out] Number of bytes transferred so far by the non-blocking transaction.
- Return values:
kStatus_Success –
kStatus_NoTransferInProgress – There is not a DMA transaction currently in progress.
-
status_t LPI2C_MasterTransferAbortEDMA(LPI2C_Type *base, lpi2c_master_edma_handle_t *handle)
Terminates a non-blocking LPI2C master transmission early.
Note
It is not safe to call this function from an IRQ handler that has a higher priority than the eDMA peripheral’s IRQ priority.
- Parameters:
base – The LPI2C peripheral base address.
handle – Pointer to the LPI2C master driver handle.
- Return values:
kStatus_Success – A transaction was successfully aborted.
kStatus_LPI2C_Idle – There is not a DMA transaction currently in progress.
-
typedef struct _lpi2c_master_edma_handle lpi2c_master_edma_handle_t
LPI2C master EDMA handle of the transfer.
-
typedef void (*lpi2c_master_edma_transfer_callback_t)(LPI2C_Type *base, lpi2c_master_edma_handle_t *handle, status_t completionStatus, void *userData)
Master DMA completion callback function pointer type.
This callback is used only for the non-blocking master transfer API. Specify the callback you wish to use in the call to LPI2C_MasterCreateEDMAHandle().
- Param base:
The LPI2C peripheral base address.
- Param handle:
Handle associated with the completed transfer.
- Param completionStatus:
Either kStatus_Success or an error code describing how the transfer completed.
- Param userData:
Arbitrary pointer-sized value passed from the application.
-
struct _lpi2c_master_edma_handle
- #include <fsl_lpi2c_edma.h>
Driver handle for master DMA APIs.
Note
The contents of this structure are private and subject to change.
Public Members
-
LPI2C_Type *base
LPI2C base pointer.
-
bool isBusy
Transfer state machine current state.
-
uint8_t nbytes
eDMA minor byte transfer count initially configured.
-
uint16_t commandBuffer[10]
LPI2C command sequence. When all 10 command words are used: Start&addr&write[1 word] + subaddr[4 words] + restart&addr&read[1 word] + receive&Size[4 words]
-
lpi2c_master_transfer_t transfer
Copy of the current transfer info.
-
lpi2c_master_edma_transfer_callback_t completionCallback
Callback function pointer.
-
void *userData
Application data passed to callback.
-
edma_handle_t *rx
Handle for receive DMA channel.
-
edma_handle_t *tx
Handle for transmit DMA channel.
-
edma_tcd_t tcds[3]
Software TCD. Three are allocated to provide enough room to align to 32-bytes.
-
LPI2C_Type *base
LPI2C Slave Driver
-
void LPI2C_SlaveGetDefaultConfig(lpi2c_slave_config_t *slaveConfig)
Provides a default configuration for the LPI2C slave peripheral.
This function provides the following default configuration for the LPI2C slave peripheral:
slaveConfig->enableSlave = true; slaveConfig->address0 = 0U; slaveConfig->address1 = 0U; slaveConfig->addressMatchMode = kLPI2C_MatchAddress0; slaveConfig->filterDozeEnable = true; slaveConfig->filterEnable = true; slaveConfig->enableGeneralCall = false; slaveConfig->sclStall.enableAck = false; slaveConfig->sclStall.enableTx = true; slaveConfig->sclStall.enableRx = true; slaveConfig->sclStall.enableAddress = true; slaveConfig->ignoreAck = false; slaveConfig->enableReceivedAddressRead = false; slaveConfig->sdaGlitchFilterWidth_ns = 0; slaveConfig->sclGlitchFilterWidth_ns = 0; slaveConfig->dataValidDelay_ns = 0; slaveConfig->clockHoldTime_ns = 0;
After calling this function, override any settings to customize the configuration, prior to initializing the master driver with LPI2C_SlaveInit(). Be sure to override at least the address0 member of the configuration structure with the desired slave address.
- Parameters:
slaveConfig – [out] User provided configuration structure that is set to default values. Refer to lpi2c_slave_config_t.
-
void LPI2C_SlaveInit(LPI2C_Type *base, const lpi2c_slave_config_t *slaveConfig, uint32_t sourceClock_Hz)
Initializes the LPI2C slave peripheral.
This function enables the peripheral clock and initializes the LPI2C slave peripheral as described by the user provided configuration.
- Parameters:
base – The LPI2C peripheral base address.
slaveConfig – User provided peripheral configuration. Use LPI2C_SlaveGetDefaultConfig() to get a set of defaults that you can override.
sourceClock_Hz – Frequency in Hertz of the LPI2C functional clock. Used to calculate the filter widths, data valid delay, and clock hold time.
-
void LPI2C_SlaveDeinit(LPI2C_Type *base)
Deinitializes the LPI2C slave peripheral.
This function disables the LPI2C slave peripheral and gates the clock. It also performs a software reset to restore the peripheral to reset conditions.
- Parameters:
base – The LPI2C peripheral base address.
-
static inline void LPI2C_SlaveReset(LPI2C_Type *base)
Performs a software reset of the LPI2C slave peripheral.
- Parameters:
base – The LPI2C peripheral base address.
-
static inline void LPI2C_SlaveEnable(LPI2C_Type *base, bool enable)
Enables or disables the LPI2C module as slave.
- Parameters:
base – The LPI2C peripheral base address.
enable – Pass true to enable or false to disable the specified LPI2C as slave.
-
static inline uint32_t LPI2C_SlaveGetStatusFlags(LPI2C_Type *base)
Gets the LPI2C slave status flags.
A bit mask with the state of all LPI2C slave status flags is returned. For each flag, the corresponding bit in the return value is set if the flag is asserted.
See also
_lpi2c_slave_flags
- Parameters:
base – The LPI2C peripheral base address.
- Returns:
State of the status flags:
1: related status flag is set.
0: related status flag is not set.
-
static inline void LPI2C_SlaveClearStatusFlags(LPI2C_Type *base, uint32_t statusMask)
Clears the LPI2C status flag state.
The following status register flags can be cleared:
kLPI2C_SlaveRepeatedStartDetectFlag
kLPI2C_SlaveStopDetectFlag
kLPI2C_SlaveBitErrFlag
kLPI2C_SlaveFifoErrFlag
Attempts to clear other flags has no effect.
See also
_lpi2c_slave_flags.
- Parameters:
base – The LPI2C peripheral base address.
statusMask – A bitmask of status flags that are to be cleared. The mask is composed of _lpi2c_slave_flags enumerators OR’d together. You may pass the result of a previous call to LPI2C_SlaveGetStatusFlags().
-
static inline void LPI2C_SlaveEnableInterrupts(LPI2C_Type *base, uint32_t interruptMask)
Enables the LPI2C slave interrupt requests.
All flags except kLPI2C_SlaveBusyFlag and kLPI2C_SlaveBusBusyFlag can be enabled as interrupts.
- Parameters:
base – The LPI2C peripheral base address.
interruptMask – Bit mask of interrupts to enable. See _lpi2c_slave_flags for the set of constants that should be OR’d together to form the bit mask.
-
static inline void LPI2C_SlaveDisableInterrupts(LPI2C_Type *base, uint32_t interruptMask)
Disables the LPI2C slave interrupt requests.
All flags except kLPI2C_SlaveBusyFlag and kLPI2C_SlaveBusBusyFlag can be enabled as interrupts.
- Parameters:
base – The LPI2C peripheral base address.
interruptMask – Bit mask of interrupts to disable. See _lpi2c_slave_flags for the set of constants that should be OR’d together to form the bit mask.
-
static inline uint32_t LPI2C_SlaveGetEnabledInterrupts(LPI2C_Type *base)
Returns the set of currently enabled LPI2C slave interrupt requests.
- Parameters:
base – The LPI2C peripheral base address.
- Returns:
A bitmask composed of _lpi2c_slave_flags enumerators OR’d together to indicate the set of enabled interrupts.
-
static inline void LPI2C_SlaveEnableDMA(LPI2C_Type *base, bool enableAddressValid, bool enableRx, bool enableTx)
Enables or disables the LPI2C slave peripheral DMA requests.
- Parameters:
base – The LPI2C peripheral base address.
enableAddressValid – Enable flag for the address valid DMA request. Pass true for enable, false for disable. The address valid DMA request is shared with the receive data DMA request.
enableRx – Enable flag for the receive data DMA request. Pass true for enable, false for disable.
enableTx – Enable flag for the transmit data DMA request. Pass true for enable, false for disable.
-
static inline bool LPI2C_SlaveGetBusIdleState(LPI2C_Type *base)
Returns whether the bus is idle.
Requires the slave mode to be enabled.
- Parameters:
base – The LPI2C peripheral base address.
- Return values:
true – Bus is busy.
false – Bus is idle.
-
static inline void LPI2C_SlaveTransmitAck(LPI2C_Type *base, bool ackOrNack)
Transmits either an ACK or NAK on the I2C bus in response to a byte from the master.
Use this function to send an ACK or NAK when the kLPI2C_SlaveTransmitAckFlag is asserted. This only happens if you enable the sclStall.enableAck field of the lpi2c_slave_config_t configuration structure used to initialize the slave peripheral.
- Parameters:
base – The LPI2C peripheral base address.
ackOrNack – Pass true for an ACK or false for a NAK.
-
static inline void LPI2C_SlaveEnableAckStall(LPI2C_Type *base, bool enable)
Enables or disables ACKSTALL.
When enables ACKSTALL, software can transmit either an ACK or NAK on the I2C bus in response to a byte from the master.
- Parameters:
base – The LPI2C peripheral base address.
enable – True will enable ACKSTALL,false will disable ACKSTALL.
-
static inline uint32_t LPI2C_SlaveGetReceivedAddress(LPI2C_Type *base)
Returns the slave address sent by the I2C master.
This function should only be called if the kLPI2C_SlaveAddressValidFlag is asserted.
- Parameters:
base – The LPI2C peripheral base address.
- Returns:
The 8-bit address matched by the LPI2C slave. Bit 0 contains the R/w direction bit, and the 7-bit slave address is in the upper 7 bits.
-
status_t LPI2C_SlaveSend(LPI2C_Type *base, void *txBuff, size_t txSize, size_t *actualTxSize)
Performs a polling send transfer on the I2C bus.
- Parameters:
base – The LPI2C peripheral base address.
txBuff – The pointer to the data to be transferred.
txSize – The length in bytes of the data to be transferred.
actualTxSize – [out]
- Returns:
Error or success status returned by API.
-
status_t LPI2C_SlaveReceive(LPI2C_Type *base, void *rxBuff, size_t rxSize, size_t *actualRxSize)
Performs a polling receive transfer on the I2C bus.
- Parameters:
base – The LPI2C peripheral base address.
rxBuff – The pointer to the data to be transferred.
rxSize – The length in bytes of the data to be transferred.
actualRxSize – [out]
- Returns:
Error or success status returned by API.
-
void LPI2C_SlaveTransferCreateHandle(LPI2C_Type *base, lpi2c_slave_handle_t *handle, lpi2c_slave_transfer_callback_t callback, void *userData)
Creates a new handle for the LPI2C slave non-blocking APIs.
The creation of a handle is for use with the non-blocking APIs. Once a handle is created, there is not a corresponding destroy handle. If the user wants to terminate a transfer, the LPI2C_SlaveTransferAbort() API shall be called.
Note
The function also enables the NVIC IRQ for the input LPI2C. Need to notice that on some SoCs the LPI2C IRQ is connected to INTMUX, in this case user needs to enable the associated INTMUX IRQ in application.
- Parameters:
base – The LPI2C peripheral base address.
handle – [out] Pointer to the LPI2C slave driver handle.
callback – User provided pointer to the asynchronous callback function.
userData – User provided pointer to the application callback data.
-
status_t LPI2C_SlaveTransferNonBlocking(LPI2C_Type *base, lpi2c_slave_handle_t *handle, uint32_t eventMask)
Starts accepting slave transfers.
Call this API after calling I2C_SlaveInit() and LPI2C_SlaveTransferCreateHandle() to start processing transactions driven by an I2C master. The slave monitors the I2C bus and pass events to the callback that was passed into the call to LPI2C_SlaveTransferCreateHandle(). The callback is always invoked from the interrupt context.
The set of events received by the callback is customizable. To do so, set the eventMask parameter to the OR’d combination of lpi2c_slave_transfer_event_t enumerators for the events you wish to receive. The kLPI2C_SlaveTransmitEvent and kLPI2C_SlaveReceiveEvent events are always enabled and do not need to be included in the mask. Alternatively, you can pass 0 to get a default set of only the transmit and receive events that are always enabled. In addition, the kLPI2C_SlaveAllEvents constant is provided as a convenient way to enable all events.
- Parameters:
base – The LPI2C peripheral base address.
handle – Pointer to lpi2c_slave_handle_t structure which stores the transfer state.
eventMask – Bit mask formed by OR’ing together lpi2c_slave_transfer_event_t enumerators to specify which events to send to the callback. Other accepted values are 0 to get a default set of only the transmit and receive events, and kLPI2C_SlaveAllEvents to enable all events.
- Return values:
kStatus_Success – Slave transfers were successfully started.
kStatus_LPI2C_Busy – Slave transfers have already been started on this handle.
-
status_t LPI2C_SlaveTransferGetCount(LPI2C_Type *base, lpi2c_slave_handle_t *handle, size_t *count)
Gets the slave transfer status during a non-blocking transfer.
- Parameters:
base – The LPI2C peripheral base address.
handle – Pointer to i2c_slave_handle_t structure.
count – [out] Pointer to a value to hold the number of bytes transferred. May be NULL if the count is not required.
- Return values:
kStatus_Success –
kStatus_NoTransferInProgress –
-
void LPI2C_SlaveTransferAbort(LPI2C_Type *base, lpi2c_slave_handle_t *handle)
Aborts the slave non-blocking transfers.
Note
This API could be called at any time to stop slave for handling the bus events.
- Parameters:
base – The LPI2C peripheral base address.
handle – Pointer to lpi2c_slave_handle_t structure which stores the transfer state.
-
void LPI2C_SlaveTransferHandleIRQ(LPI2C_Type *base, lpi2c_slave_handle_t *handle)
Reusable routine to handle slave interrupts.
Note
This function does not need to be called unless you are reimplementing the non blocking API’s interrupt handler routines to add special functionality.
- Parameters:
base – The LPI2C peripheral base address.
handle – Pointer to lpi2c_slave_handle_t structure which stores the transfer state.
-
enum _lpi2c_slave_flags
LPI2C slave peripheral flags.
The following status register flags can be cleared:
kLPI2C_SlaveRepeatedStartDetectFlag
kLPI2C_SlaveStopDetectFlag
kLPI2C_SlaveBitErrFlag
kLPI2C_SlaveFifoErrFlag
All flags except kLPI2C_SlaveBusyFlag and kLPI2C_SlaveBusBusyFlag can be enabled as interrupts.
Note
These enumerations are meant to be OR’d together to form a bit mask.
Values:
-
enumerator kLPI2C_SlaveTxReadyFlag
Transmit data flag
-
enumerator kLPI2C_SlaveRxReadyFlag
Receive data flag
-
enumerator kLPI2C_SlaveAddressValidFlag
Address valid flag
-
enumerator kLPI2C_SlaveTransmitAckFlag
Transmit ACK flag
-
enumerator kLPI2C_SlaveRepeatedStartDetectFlag
Repeated start detect flag
-
enumerator kLPI2C_SlaveStopDetectFlag
Stop detect flag
-
enumerator kLPI2C_SlaveBitErrFlag
Bit error flag
-
enumerator kLPI2C_SlaveFifoErrFlag
FIFO error flag
-
enumerator kLPI2C_SlaveAddressMatch0Flag
Address match 0 flag
-
enumerator kLPI2C_SlaveAddressMatch1Flag
Address match 1 flag
-
enumerator kLPI2C_SlaveGeneralCallFlag
General call flag
-
enumerator kLPI2C_SlaveBusyFlag
Master busy flag
-
enumerator kLPI2C_SlaveBusBusyFlag
Bus busy flag
-
enumerator kLPI2C_SlaveClearFlags
All flags which are cleared by the driver upon starting a transfer.
-
enumerator kLPI2C_SlaveIrqFlags
IRQ sources enabled by the non-blocking transactional API.
-
enumerator kLPI2C_SlaveErrorFlags
Errors to check for.
-
enum _lpi2c_slave_address_match
LPI2C slave address match options.
Values:
-
enumerator kLPI2C_MatchAddress0
Match only address 0.
-
enumerator kLPI2C_MatchAddress0OrAddress1
Match either address 0 or address 1.
-
enumerator kLPI2C_MatchAddress0ThroughAddress1
Match a range of slave addresses from address 0 through address 1.
-
enumerator kLPI2C_MatchAddress0
-
enum _lpi2c_slave_transfer_event
Set of events sent to the callback for non blocking slave transfers.
These event enumerations are used for two related purposes. First, a bit mask created by OR’ing together events is passed to LPI2C_SlaveTransferNonBlocking() in order to specify which events to enable. Then, when the slave callback is invoked, it is passed the current event through its transfer parameter.
Note
These enumerations are meant to be OR’d together to form a bit mask of events.
Values:
-
enumerator kLPI2C_SlaveAddressMatchEvent
Received the slave address after a start or repeated start.
-
enumerator kLPI2C_SlaveTransmitEvent
Callback is requested to provide data to transmit (slave-transmitter role).
-
enumerator kLPI2C_SlaveReceiveEvent
Callback is requested to provide a buffer in which to place received data (slave-receiver role).
-
enumerator kLPI2C_SlaveTransmitAckEvent
Callback needs to either transmit an ACK or NACK.
-
enumerator kLPI2C_SlaveRepeatedStartEvent
A repeated start was detected.
-
enumerator kLPI2C_SlaveCompletionEvent
A stop was detected, completing the transfer.
-
enumerator kLPI2C_SlaveAllEvents
Bit mask of all available events.
-
enumerator kLPI2C_SlaveAddressMatchEvent
-
typedef enum _lpi2c_slave_address_match lpi2c_slave_address_match_t
LPI2C slave address match options.
-
typedef struct _lpi2c_slave_config lpi2c_slave_config_t
Structure with settings to initialize the LPI2C slave module.
This structure holds configuration settings for the LPI2C slave peripheral. To initialize this structure to reasonable defaults, call the LPI2C_SlaveGetDefaultConfig() function and pass a pointer to your configuration structure instance.
The configuration structure can be made constant so it resides in flash.
-
typedef enum _lpi2c_slave_transfer_event lpi2c_slave_transfer_event_t
Set of events sent to the callback for non blocking slave transfers.
These event enumerations are used for two related purposes. First, a bit mask created by OR’ing together events is passed to LPI2C_SlaveTransferNonBlocking() in order to specify which events to enable. Then, when the slave callback is invoked, it is passed the current event through its transfer parameter.
Note
These enumerations are meant to be OR’d together to form a bit mask of events.
-
typedef struct _lpi2c_slave_transfer lpi2c_slave_transfer_t
LPI2C slave transfer structure.
-
typedef struct _lpi2c_slave_handle lpi2c_slave_handle_t
LPI2C slave handle structure.
-
typedef void (*lpi2c_slave_transfer_callback_t)(LPI2C_Type *base, lpi2c_slave_transfer_t *transfer, void *userData)
Slave event callback function pointer type.
This callback is used only for the slave non-blocking transfer API. To install a callback, use the LPI2C_SlaveSetCallback() function after you have created a handle.
- Param base:
Base address for the LPI2C instance on which the event occurred.
- Param transfer:
Pointer to transfer descriptor containing values passed to and/or from the callback.
- Param userData:
Arbitrary pointer-sized value passed from the application.
-
struct _lpi2c_slave_config
- #include <fsl_lpi2c.h>
Structure with settings to initialize the LPI2C slave module.
This structure holds configuration settings for the LPI2C slave peripheral. To initialize this structure to reasonable defaults, call the LPI2C_SlaveGetDefaultConfig() function and pass a pointer to your configuration structure instance.
The configuration structure can be made constant so it resides in flash.
Public Members
-
bool enableSlave
Enable slave mode.
-
uint8_t address0
Slave’s 7-bit address.
-
uint8_t address1
Alternate slave 7-bit address.
-
lpi2c_slave_address_match_t addressMatchMode
Address matching options.
-
bool filterDozeEnable
Enable digital glitch filter in doze mode.
-
bool filterEnable
Enable digital glitch filter.
-
bool enableGeneralCall
Enable general call address matching.
-
struct _lpi2c_slave_config sclStall
SCL stall enable options.
-
bool ignoreAck
Continue transfers after a NACK is detected.
-
bool enableReceivedAddressRead
Enable reading the address received address as the first byte of data.
-
uint32_t sdaGlitchFilterWidth_ns
Width in nanoseconds of the digital filter on the SDA signal. Set to 0 to disable.
-
uint32_t sclGlitchFilterWidth_ns
Width in nanoseconds of the digital filter on the SCL signal. Set to 0 to disable.
-
uint32_t dataValidDelay_ns
Width in nanoseconds of the data valid delay.
-
uint32_t clockHoldTime_ns
Width in nanoseconds of the clock hold time.
-
bool enableSlave
-
struct _lpi2c_slave_transfer
- #include <fsl_lpi2c.h>
LPI2C slave transfer structure.
Public Members
-
lpi2c_slave_transfer_event_t event
Reason the callback is being invoked.
-
uint8_t receivedAddress
Matching address send by master.
-
uint8_t *data
Transfer buffer
-
size_t dataSize
Transfer size
-
status_t completionStatus
Success or error code describing how the transfer completed. Only applies for kLPI2C_SlaveCompletionEvent.
-
size_t transferredCount
Number of bytes actually transferred since start or last repeated start.
-
lpi2c_slave_transfer_event_t event
-
struct _lpi2c_slave_handle
- #include <fsl_lpi2c.h>
LPI2C slave handle structure.
Note
The contents of this structure are private and subject to change.
Public Members
-
lpi2c_slave_transfer_t transfer
LPI2C slave transfer copy.
-
bool isBusy
Whether transfer is busy.
-
bool wasTransmit
Whether the last transfer was a transmit.
-
uint32_t eventMask
Mask of enabled events.
-
uint32_t transferredCount
Count of bytes transferred.
-
lpi2c_slave_transfer_callback_t callback
Callback function called at transfer event.
-
void *userData
Callback parameter passed to callback.
-
lpi2c_slave_transfer_t transfer
-
struct sclStall
Public Members
-
bool enableAck
Enables SCL clock stretching during slave-transmit address byte(s) and slave-receiver address and data byte(s) to allow software to write the Transmit ACK Register before the ACK or NACK is transmitted. Clock stretching occurs when transmitting the 9th bit. When enableAckSCLStall is enabled, there is no need to set either enableRxDataSCLStall or enableAddressSCLStall.
-
bool enableTx
Enables SCL clock stretching when the transmit data flag is set during a slave-transmit transfer.
-
bool enableRx
Enables SCL clock stretching when receive data flag is set during a slave-receive transfer.
-
bool enableAddress
Enables SCL clock stretching when the address valid flag is asserted.
-
bool enableAck
LPSPI: Low Power Serial Peripheral Interface
LPSPI Peripheral driver
-
void LPSPI_MasterInit(LPSPI_Type *base, const lpspi_master_config_t *masterConfig, uint32_t srcClock_Hz)
Initializes the LPSPI master.
- Parameters:
base – LPSPI peripheral address.
masterConfig – Pointer to structure lpspi_master_config_t.
srcClock_Hz – Module source input clock in Hertz
-
void LPSPI_MasterGetDefaultConfig(lpspi_master_config_t *masterConfig)
Sets the lpspi_master_config_t structure to default values.
This API initializes the configuration structure for LPSPI_MasterInit(). The initialized structure can remain unchanged in LPSPI_MasterInit(), or can be modified before calling the LPSPI_MasterInit(). Example:
lpspi_master_config_t masterConfig; LPSPI_MasterGetDefaultConfig(&masterConfig);
- Parameters:
masterConfig – pointer to lpspi_master_config_t structure
-
void LPSPI_SlaveInit(LPSPI_Type *base, const lpspi_slave_config_t *slaveConfig)
LPSPI slave configuration.
- Parameters:
base – LPSPI peripheral address.
slaveConfig – Pointer to a structure lpspi_slave_config_t.
-
void LPSPI_SlaveGetDefaultConfig(lpspi_slave_config_t *slaveConfig)
Sets the lpspi_slave_config_t structure to default values.
This API initializes the configuration structure for LPSPI_SlaveInit(). The initialized structure can remain unchanged in LPSPI_SlaveInit() or can be modified before calling the LPSPI_SlaveInit(). Example:
lpspi_slave_config_t slaveConfig; LPSPI_SlaveGetDefaultConfig(&slaveConfig);
- Parameters:
slaveConfig – pointer to lpspi_slave_config_t structure.
-
void LPSPI_Deinit(LPSPI_Type *base)
De-initializes the LPSPI peripheral. Call this API to disable the LPSPI clock.
- Parameters:
base – LPSPI peripheral address.
-
void LPSPI_Reset(LPSPI_Type *base)
Restores the LPSPI peripheral to reset state. Note that this function sets all registers to reset state. As a result, the LPSPI module can’t work after calling this API.
- Parameters:
base – LPSPI peripheral address.
-
uint32_t LPSPI_GetInstance(LPSPI_Type *base)
Get the LPSPI instance from peripheral base address.
- Parameters:
base – LPSPI peripheral base address.
- Returns:
LPSPI instance.
-
static inline void LPSPI_Enable(LPSPI_Type *base, bool enable)
Enables the LPSPI peripheral and sets the MCR MDIS to 0.
- Parameters:
base – LPSPI peripheral address.
enable – Pass true to enable module, false to disable module.
-
static inline uint32_t LPSPI_GetStatusFlags(LPSPI_Type *base)
Gets the LPSPI status flag state.
- Parameters:
base – LPSPI peripheral address.
- Returns:
The LPSPI status(in SR register).
-
static inline uint8_t LPSPI_GetTxFifoSize(LPSPI_Type *base)
Gets the LPSPI Tx FIFO size.
- Parameters:
base – LPSPI peripheral address.
- Returns:
The LPSPI Tx FIFO size.
-
static inline uint8_t LPSPI_GetRxFifoSize(LPSPI_Type *base)
Gets the LPSPI Rx FIFO size.
- Parameters:
base – LPSPI peripheral address.
- Returns:
The LPSPI Rx FIFO size.
-
static inline uint32_t LPSPI_GetTxFifoCount(LPSPI_Type *base)
Gets the LPSPI Tx FIFO count.
- Parameters:
base – LPSPI peripheral address.
- Returns:
The number of words in the transmit FIFO.
-
static inline uint32_t LPSPI_GetRxFifoCount(LPSPI_Type *base)
Gets the LPSPI Rx FIFO count.
- Parameters:
base – LPSPI peripheral address.
- Returns:
The number of words in the receive FIFO.
-
static inline void LPSPI_ClearStatusFlags(LPSPI_Type *base, uint32_t statusFlags)
Clears the LPSPI status flag.
This function clears the desired status bit by using a write-1-to-clear. The user passes in the base and the desired status flag bit to clear. The list of status flags is defined in the _lpspi_flags. Example usage:
LPSPI_ClearStatusFlags(base, kLPSPI_TxDataRequestFlag|kLPSPI_RxDataReadyFlag);
- Parameters:
base – LPSPI peripheral address.
statusFlags – The status flag used from type _lpspi_flags.
-
static inline uint32_t LPSPI_GetTcr(LPSPI_Type *base)
-
static inline void LPSPI_EnableInterrupts(LPSPI_Type *base, uint32_t mask)
Enables the LPSPI interrupts.
This function configures the various interrupt masks of the LPSPI. The parameters are base and an interrupt mask. Note that, for Tx fill and Rx FIFO drain requests, enabling the interrupt request disables the DMA request.
LPSPI_EnableInterrupts(base, kLPSPI_TxInterruptEnable | kLPSPI_RxInterruptEnable );
- Parameters:
base – LPSPI peripheral address.
mask – The interrupt mask; Use the enum _lpspi_interrupt_enable.
-
static inline void LPSPI_DisableInterrupts(LPSPI_Type *base, uint32_t mask)
Disables the LPSPI interrupts.
LPSPI_DisableInterrupts(base, kLPSPI_TxInterruptEnable | kLPSPI_RxInterruptEnable );
- Parameters:
base – LPSPI peripheral address.
mask – The interrupt mask; Use the enum _lpspi_interrupt_enable.
-
static inline void LPSPI_EnableDMA(LPSPI_Type *base, uint32_t mask)
Enables the LPSPI DMA request.
This function configures the Rx and Tx DMA mask of the LPSPI. The parameters are base and a DMA mask.
LPSPI_EnableDMA(base, kLPSPI_TxDmaEnable | kLPSPI_RxDmaEnable);
- Parameters:
base – LPSPI peripheral address.
mask – The interrupt mask; Use the enum _lpspi_dma_enable.
-
static inline void LPSPI_DisableDMA(LPSPI_Type *base, uint32_t mask)
Disables the LPSPI DMA request.
This function configures the Rx and Tx DMA mask of the LPSPI. The parameters are base and a DMA mask.
SPI_DisableDMA(base, kLPSPI_TxDmaEnable | kLPSPI_RxDmaEnable);
- Parameters:
base – LPSPI peripheral address.
mask – The interrupt mask; Use the enum _lpspi_dma_enable.
-
static inline uint32_t LPSPI_GetTxRegisterAddress(LPSPI_Type *base)
Gets the LPSPI Transmit Data Register address for a DMA operation.
This function gets the LPSPI Transmit Data Register address because this value is needed for the DMA operation. This function can be used for either master or slave mode.
- Parameters:
base – LPSPI peripheral address.
- Returns:
The LPSPI Transmit Data Register address.
-
static inline uint32_t LPSPI_GetRxRegisterAddress(LPSPI_Type *base)
Gets the LPSPI Receive Data Register address for a DMA operation.
This function gets the LPSPI Receive Data Register address because this value is needed for the DMA operation. This function can be used for either master or slave mode.
- Parameters:
base – LPSPI peripheral address.
- Returns:
The LPSPI Receive Data Register address.
-
bool LPSPI_CheckTransferArgument(LPSPI_Type *base, lpspi_transfer_t *transfer, bool isEdma)
Check the argument for transfer .
- Parameters:
base – LPSPI peripheral address.
transfer – the transfer struct to be used.
isEdma – True to check for EDMA transfer, false to check interrupt non-blocking transfer
- Returns:
Return true for right and false for wrong.
-
static inline void LPSPI_SetMasterSlaveMode(LPSPI_Type *base, lpspi_master_slave_mode_t mode)
Configures the LPSPI for either master or slave.
Note that the CFGR1 should only be written when the LPSPI is disabled (LPSPIx_CR_MEN = 0).
- Parameters:
base – LPSPI peripheral address.
mode – Mode setting (master or slave) of type lpspi_master_slave_mode_t.
-
static inline void LPSPI_SelectTransferPCS(LPSPI_Type *base, lpspi_which_pcs_t select)
Configures the peripheral chip select used for the transfer.
- Parameters:
base – LPSPI peripheral address.
select – LPSPI Peripheral Chip Select (PCS) configuration.
-
static inline void LPSPI_SetPCSContinous(LPSPI_Type *base, bool IsContinous)
Set the PCS signal to continuous or uncontinuous mode.
Note
In master mode, continuous transfer will keep the PCS asserted at the end of the frame size, until a command word is received that starts a new frame. So PCS must be set back to uncontinuous when transfer finishes. In slave mode, when continuous transfer is enabled, the LPSPI will only transmit the first frame size bits, after that the LPSPI will transmit received data back (assuming a 32-bit shift register).
- Parameters:
base – LPSPI peripheral address.
IsContinous – True to set the transfer PCS to continuous mode, false to set to uncontinuous mode.
-
static inline bool LPSPI_IsMaster(LPSPI_Type *base)
Returns whether the LPSPI module is in master mode.
- Parameters:
base – LPSPI peripheral address.
- Returns:
Returns true if the module is in master mode or false if the module is in slave mode.
-
static inline void LPSPI_FlushFifo(LPSPI_Type *base, bool flushTxFifo, bool flushRxFifo)
Flushes the LPSPI FIFOs.
- Parameters:
base – LPSPI peripheral address.
flushTxFifo – Flushes (true) the Tx FIFO, else do not flush (false) the Tx FIFO.
flushRxFifo – Flushes (true) the Rx FIFO, else do not flush (false) the Rx FIFO.
-
static inline void LPSPI_SetFifoWatermarks(LPSPI_Type *base, uint32_t txWater, uint32_t rxWater)
Sets the transmit and receive FIFO watermark values.
This function allows the user to set the receive and transmit FIFO watermarks. The function does not compare the watermark settings to the FIFO size. The FIFO watermark should not be equal to or greater than the FIFO size. It is up to the higher level driver to make this check.
- Parameters:
base – LPSPI peripheral address.
txWater – The TX FIFO watermark value. Writing a value equal or greater than the FIFO size is truncated.
rxWater – The RX FIFO watermark value. Writing a value equal or greater than the FIFO size is truncated.
-
static inline void LPSPI_SetAllPcsPolarity(LPSPI_Type *base, uint32_t mask)
Configures all LPSPI peripheral chip select polarities simultaneously.
Note that the CFGR1 should only be written when the LPSPI is disabled (LPSPIx_CR_MEN = 0).
This is an example: PCS0 and PCS1 set to active low and other PCSs set to active high. Note that the number of PCS is device-specific.
LPSPI_SetAllPcsPolarity(base, kLPSPI_Pcs0ActiveLow | kLPSPI_Pcs1ActiveLow);
- Parameters:
base – LPSPI peripheral address.
mask – The PCS polarity mask; Use the enum _lpspi_pcs_polarity.
-
static inline void LPSPI_SetFrameSize(LPSPI_Type *base, uint32_t frameSize)
Configures the frame size.
The minimum frame size is 8-bits and the maximum frame size is 4096-bits. If the frame size is less than or equal to 32-bits, the word size and frame size are identical. If the frame size is greater than 32-bits, the word size is 32-bits for each word except the last (the last word contains the remainder bits if the frame size is not divisible by 32). The minimum word size is 2-bits. A frame size of 33-bits (or similar) is not supported.
Note 1: The transmit command register should be initialized before enabling the LPSPI in slave mode, although the command register does not update until after the LPSPI is enabled. After it is enabled, the transmit command register should only be changed if the LPSPI is idle.
Note 2: The transmit and command FIFO is a combined FIFO that includes both transmit data and command words. That means the TCR register should be written to when the Tx FIFO is not full.
- Parameters:
base – LPSPI peripheral address.
frameSize – The frame size in number of bits.
-
uint32_t LPSPI_MasterSetBaudRate(LPSPI_Type *base, uint32_t baudRate_Bps, uint32_t srcClock_Hz, uint32_t *tcrPrescaleValue)
Sets the LPSPI baud rate in bits per second.
This function takes in the desired bitsPerSec (baud rate) and calculates the nearest possible baud rate without exceeding the desired baud rate and returns the calculated baud rate in bits-per-second. It requires the caller to provide the frequency of the module source clock (in Hertz). Note that the baud rate does not go into effect until the Transmit Control Register (TCR) is programmed with the prescale value. Hence, this function returns the prescale tcrPrescaleValue parameter for later programming in the TCR. The higher level peripheral driver should alert the user of an out of range baud rate input.
Note that the LPSPI module must first be disabled before configuring this. Note that the LPSPI module must be configured for master mode before configuring this.
- Parameters:
base – LPSPI peripheral address.
baudRate_Bps – The desired baud rate in bits per second.
srcClock_Hz – Module source input clock in Hertz.
tcrPrescaleValue – The TCR prescale value needed to program the TCR.
- Returns:
The actual calculated baud rate. This function may also return a “0” if the LPSPI is not configured for master mode or if the LPSPI module is not disabled.
-
void LPSPI_MasterSetDelayScaler(LPSPI_Type *base, uint32_t scaler, lpspi_delay_type_t whichDelay)
Manually configures a specific LPSPI delay parameter (module must be disabled to change the delay values).
This function configures the following: SCK to PCS delay, or PCS to SCK delay, or The configurations must occur between the transfer delay.
The delay names are available in type lpspi_delay_type_t.
The user passes the desired delay along with the delay value. This allows the user to directly set the delay values if they have pre-calculated them or if they simply wish to manually increment the value.
Note that the LPSPI module must first be disabled before configuring this. Note that the LPSPI module must be configured for master mode before configuring this.
- Parameters:
base – LPSPI peripheral address.
scaler – The 8-bit delay value 0x00 to 0xFF (255).
whichDelay – The desired delay to configure, must be of type lpspi_delay_type_t.
-
uint32_t LPSPI_MasterSetDelayTimes(LPSPI_Type *base, uint32_t delayTimeInNanoSec, lpspi_delay_type_t whichDelay, uint32_t srcClock_Hz)
Calculates the delay based on the desired delay input in nanoseconds (module must be disabled to change the delay values).
This function calculates the values for the following: SCK to PCS delay, or PCS to SCK delay, or The configurations must occur between the transfer delay.
The delay names are available in type lpspi_delay_type_t.
The user passes the desired delay and the desired delay value in nano-seconds. The function calculates the value needed for the desired delay parameter and returns the actual calculated delay because an exact delay match may not be possible. In this case, the closest match is calculated without going below the desired delay value input. It is possible to input a very large delay value that exceeds the capability of the part, in which case the maximum supported delay is returned. It is up to the higher level peripheral driver to alert the user of an out of range delay input.
Note that the LPSPI module must be configured for master mode before configuring this. And note that the delayTime = LPSPI_clockSource / (PRESCALE * Delay_scaler).
- Parameters:
base – LPSPI peripheral address.
delayTimeInNanoSec – The desired delay value in nano-seconds.
whichDelay – The desired delay to configuration, which must be of type lpspi_delay_type_t.
srcClock_Hz – Module source input clock in Hertz.
- Returns:
actual Calculated delay value in nano-seconds.
-
static inline void LPSPI_WriteData(LPSPI_Type *base, uint32_t data)
Writes data into the transmit data buffer.
This function writes data passed in by the user to the Transmit Data Register (TDR). The user can pass up to 32-bits of data to load into the TDR. If the frame size exceeds 32-bits, the user has to manage sending the data one 32-bit word at a time. Any writes to the TDR result in an immediate push to the transmit FIFO. This function can be used for either master or slave modes.
- Parameters:
base – LPSPI peripheral address.
data – The data word to be sent.
-
static inline uint32_t LPSPI_ReadData(LPSPI_Type *base)
Reads data from the data buffer.
This function reads the data from the Receive Data Register (RDR). This function can be used for either master or slave mode.
- Parameters:
base – LPSPI peripheral address.
- Returns:
The data read from the data buffer.
-
void LPSPI_SetDummyData(LPSPI_Type *base, uint8_t dummyData)
Set up the dummy data.
- Parameters:
base – LPSPI peripheral address.
dummyData – Data to be transferred when tx buffer is NULL. Note: This API has no effect when LPSPI in slave interrupt mode, because driver will set the TXMSK bit to 1 if txData is NULL, no data is loaded from transmit FIFO and output pin is tristated.
-
void LPSPI_MasterTransferCreateHandle(LPSPI_Type *base, lpspi_master_handle_t *handle, lpspi_master_transfer_callback_t callback, void *userData)
Initializes the LPSPI master handle.
This function initializes the LPSPI handle, which can be used for other LPSPI transactional APIs. Usually, for a specified LPSPI instance, call this API once to get the initialized handle.
- Parameters:
base – LPSPI peripheral address.
handle – LPSPI handle pointer to lpspi_master_handle_t.
callback – DSPI callback.
userData – callback function parameter.
-
status_t LPSPI_MasterTransferBlocking(LPSPI_Type *base, lpspi_transfer_t *transfer)
LPSPI master transfer data using a polling method.
This function transfers data using a polling method. This is a blocking function, which does not return until all transfers have been completed.
Note: The transfer data size should be integer multiples of bytesPerFrame if bytesPerFrame is less than or equal to 4. For bytesPerFrame greater than 4: The transfer data size should be equal to bytesPerFrame if the bytesPerFrame is not integer multiples of 4. Otherwise, the transfer data size can be an integer multiple of bytesPerFrame.
- Parameters:
base – LPSPI peripheral address.
transfer – pointer to lpspi_transfer_t structure.
- Returns:
status of status_t.
-
status_t LPSPI_MasterTransferNonBlocking(LPSPI_Type *base, lpspi_master_handle_t *handle, lpspi_transfer_t *transfer)
LPSPI master transfer data using an interrupt method.
This function transfers data using an interrupt method. This is a non-blocking function, which returns right away. When all data is transferred, the callback function is called.
Note: The transfer data size should be integer multiples of bytesPerFrame if bytesPerFrame is less than or equal to 4. For bytesPerFrame greater than 4: The transfer data size should be equal to bytesPerFrame if the bytesPerFrame is not integer multiples of 4. Otherwise, the transfer data size can be an integer multiple of bytesPerFrame.
- Parameters:
base – LPSPI peripheral address.
handle – pointer to lpspi_master_handle_t structure which stores the transfer state.
transfer – pointer to lpspi_transfer_t structure.
- Returns:
status of status_t.
-
status_t LPSPI_MasterTransferGetCount(LPSPI_Type *base, lpspi_master_handle_t *handle, size_t *count)
Gets the master transfer remaining bytes.
This function gets the master transfer remaining bytes.
- Parameters:
base – LPSPI peripheral address.
handle – pointer to lpspi_master_handle_t structure which stores the transfer state.
count – Number of bytes transferred so far by the non-blocking transaction.
- Returns:
status of status_t.
-
void LPSPI_MasterTransferAbort(LPSPI_Type *base, lpspi_master_handle_t *handle)
LPSPI master abort transfer which uses an interrupt method.
This function aborts a transfer which uses an interrupt method.
- Parameters:
base – LPSPI peripheral address.
handle – pointer to lpspi_master_handle_t structure which stores the transfer state.
-
void LPSPI_MasterTransferHandleIRQ(LPSPI_Type *base, lpspi_master_handle_t *handle)
LPSPI Master IRQ handler function.
This function processes the LPSPI transmit and receive IRQ.
- Parameters:
base – LPSPI peripheral address.
handle – pointer to lpspi_master_handle_t structure which stores the transfer state.
-
void LPSPI_SlaveTransferCreateHandle(LPSPI_Type *base, lpspi_slave_handle_t *handle, lpspi_slave_transfer_callback_t callback, void *userData)
Initializes the LPSPI slave handle.
This function initializes the LPSPI handle, which can be used for other LPSPI transactional APIs. Usually, for a specified LPSPI instance, call this API once to get the initialized handle.
- Parameters:
base – LPSPI peripheral address.
handle – LPSPI handle pointer to lpspi_slave_handle_t.
callback – DSPI callback.
userData – callback function parameter.
-
status_t LPSPI_SlaveTransferNonBlocking(LPSPI_Type *base, lpspi_slave_handle_t *handle, lpspi_transfer_t *transfer)
LPSPI slave transfer data using an interrupt method.
This function transfer data using an interrupt method. This is a non-blocking function, which returns right away. When all data is transferred, the callback function is called.
Note: The transfer data size should be integer multiples of bytesPerFrame if bytesPerFrame is less than or equal to 4. For bytesPerFrame greater than 4: The transfer data size should be equal to bytesPerFrame if the bytesPerFrame is not an integer multiple of 4. Otherwise, the transfer data size can be an integer multiple of bytesPerFrame.
- Parameters:
base – LPSPI peripheral address.
handle – pointer to lpspi_slave_handle_t structure which stores the transfer state.
transfer – pointer to lpspi_transfer_t structure.
- Returns:
status of status_t.
-
status_t LPSPI_SlaveTransferGetCount(LPSPI_Type *base, lpspi_slave_handle_t *handle, size_t *count)
Gets the slave transfer remaining bytes.
This function gets the slave transfer remaining bytes.
- Parameters:
base – LPSPI peripheral address.
handle – pointer to lpspi_slave_handle_t structure which stores the transfer state.
count – Number of bytes transferred so far by the non-blocking transaction.
- Returns:
status of status_t.
-
void LPSPI_SlaveTransferAbort(LPSPI_Type *base, lpspi_slave_handle_t *handle)
LPSPI slave aborts a transfer which uses an interrupt method.
This function aborts a transfer which uses an interrupt method.
- Parameters:
base – LPSPI peripheral address.
handle – pointer to lpspi_slave_handle_t structure which stores the transfer state.
-
void LPSPI_SlaveTransferHandleIRQ(LPSPI_Type *base, lpspi_slave_handle_t *handle)
LPSPI Slave IRQ handler function.
This function processes the LPSPI transmit and receives an IRQ.
- Parameters:
base – LPSPI peripheral address.
handle – pointer to lpspi_slave_handle_t structure which stores the transfer state.
-
bool LPSPI_WaitTxFifoEmpty(LPSPI_Type *base)
Wait for tx FIFO to be empty.
This function wait the tx fifo empty
- Parameters:
base – LPSPI peripheral address.
- Returns:
true for the tx FIFO is ready, false is not.
-
FSL_LPSPI_DRIVER_VERSION
LPSPI driver version.
Status for the LPSPI driver.
Values:
-
enumerator kStatus_LPSPI_Busy
LPSPI transfer is busy.
-
enumerator kStatus_LPSPI_Error
LPSPI driver error.
-
enumerator kStatus_LPSPI_Idle
LPSPI is idle.
-
enumerator kStatus_LPSPI_OutOfRange
LPSPI transfer out Of range.
-
enumerator kStatus_LPSPI_Timeout
LPSPI timeout polling status flags.
-
enumerator kStatus_LPSPI_Busy
-
enum _lpspi_flags
LPSPI status flags in SPIx_SR register.
Values:
-
enumerator kLPSPI_TxDataRequestFlag
Transmit data flag
-
enumerator kLPSPI_RxDataReadyFlag
Receive data flag
-
enumerator kLPSPI_WordCompleteFlag
Word Complete flag
-
enumerator kLPSPI_FrameCompleteFlag
Frame Complete flag
-
enumerator kLPSPI_TransferCompleteFlag
Transfer Complete flag
-
enumerator kLPSPI_TransmitErrorFlag
Transmit Error flag (FIFO underrun)
-
enumerator kLPSPI_ReceiveErrorFlag
Receive Error flag (FIFO overrun)
-
enumerator kLPSPI_DataMatchFlag
Data Match flag
-
enumerator kLPSPI_ModuleBusyFlag
Module Busy flag
-
enumerator kLPSPI_AllStatusFlag
Used for clearing all w1c status flags
-
enumerator kLPSPI_TxDataRequestFlag
-
enum _lpspi_interrupt_enable
LPSPI interrupt source.
Values:
-
enumerator kLPSPI_TxInterruptEnable
Transmit data interrupt enable
-
enumerator kLPSPI_RxInterruptEnable
Receive data interrupt enable
-
enumerator kLPSPI_WordCompleteInterruptEnable
Word complete interrupt enable
-
enumerator kLPSPI_FrameCompleteInterruptEnable
Frame complete interrupt enable
-
enumerator kLPSPI_TransferCompleteInterruptEnable
Transfer complete interrupt enable
-
enumerator kLPSPI_TransmitErrorInterruptEnable
Transmit error interrupt enable(FIFO underrun)
-
enumerator kLPSPI_ReceiveErrorInterruptEnable
Receive Error interrupt enable (FIFO overrun)
-
enumerator kLPSPI_DataMatchInterruptEnable
Data Match interrupt enable
-
enumerator kLPSPI_AllInterruptEnable
All above interrupts enable.
-
enumerator kLPSPI_TxInterruptEnable
-
enum _lpspi_dma_enable
LPSPI DMA source.
Values:
-
enumerator kLPSPI_TxDmaEnable
Transmit data DMA enable
-
enumerator kLPSPI_RxDmaEnable
Receive data DMA enable
-
enumerator kLPSPI_TxDmaEnable
-
enum _lpspi_master_slave_mode
LPSPI master or slave mode configuration.
Values:
-
enumerator kLPSPI_Master
LPSPI peripheral operates in master mode.
-
enumerator kLPSPI_Slave
LPSPI peripheral operates in slave mode.
-
enumerator kLPSPI_Master
-
enum _lpspi_which_pcs_config
LPSPI Peripheral Chip Select (PCS) configuration (which PCS to configure).
Values:
-
enumerator kLPSPI_Pcs0
PCS[0]
-
enumerator kLPSPI_Pcs1
PCS[1]
-
enumerator kLPSPI_Pcs2
PCS[2]
-
enumerator kLPSPI_Pcs3
PCS[3]
-
enumerator kLPSPI_Pcs0
-
enum _lpspi_pcs_polarity_config
LPSPI Peripheral Chip Select (PCS) Polarity configuration.
Values:
-
enumerator kLPSPI_PcsActiveHigh
PCS Active High (idles low)
-
enumerator kLPSPI_PcsActiveLow
PCS Active Low (idles high)
-
enumerator kLPSPI_PcsActiveHigh
-
enum _lpspi_pcs_polarity
LPSPI Peripheral Chip Select (PCS) Polarity.
Values:
-
enumerator kLPSPI_Pcs0ActiveLow
Pcs0 Active Low (idles high).
-
enumerator kLPSPI_Pcs1ActiveLow
Pcs1 Active Low (idles high).
-
enumerator kLPSPI_Pcs2ActiveLow
Pcs2 Active Low (idles high).
-
enumerator kLPSPI_Pcs3ActiveLow
Pcs3 Active Low (idles high).
-
enumerator kLPSPI_PcsAllActiveLow
Pcs0 to Pcs5 Active Low (idles high).
-
enumerator kLPSPI_Pcs0ActiveLow
-
enum _lpspi_clock_polarity
LPSPI clock polarity configuration.
Values:
-
enumerator kLPSPI_ClockPolarityActiveHigh
CPOL=0. Active-high LPSPI clock (idles low)
-
enumerator kLPSPI_ClockPolarityActiveLow
CPOL=1. Active-low LPSPI clock (idles high)
-
enumerator kLPSPI_ClockPolarityActiveHigh
-
enum _lpspi_clock_phase
LPSPI clock phase configuration.
Values:
-
enumerator kLPSPI_ClockPhaseFirstEdge
CPHA=0. Data is captured on the leading edge of the SCK and changed on the following edge.
-
enumerator kLPSPI_ClockPhaseSecondEdge
CPHA=1. Data is changed on the leading edge of the SCK and captured on the following edge.
-
enumerator kLPSPI_ClockPhaseFirstEdge
-
enum _lpspi_shift_direction
LPSPI data shifter direction options.
Values:
-
enumerator kLPSPI_MsbFirst
Data transfers start with most significant bit.
-
enumerator kLPSPI_LsbFirst
Data transfers start with least significant bit.
-
enumerator kLPSPI_MsbFirst
-
enum _lpspi_host_request_select
LPSPI Host Request select configuration.
Values:
-
enumerator kLPSPI_HostReqExtPin
Host Request is an ext pin.
-
enumerator kLPSPI_HostReqInternalTrigger
Host Request is an internal trigger.
-
enumerator kLPSPI_HostReqExtPin
-
enum _lpspi_match_config
LPSPI Match configuration options.
Values:
-
enumerator kLPSI_MatchDisabled
LPSPI Match Disabled.
-
enumerator kLPSI_1stWordEqualsM0orM1
LPSPI Match Enabled.
-
enumerator kLPSI_AnyWordEqualsM0orM1
LPSPI Match Enabled.
-
enumerator kLPSI_1stWordEqualsM0and2ndWordEqualsM1
LPSPI Match Enabled.
-
enumerator kLPSI_AnyWordEqualsM0andNxtWordEqualsM1
LPSPI Match Enabled.
-
enumerator kLPSI_1stWordAndM1EqualsM0andM1
LPSPI Match Enabled.
-
enumerator kLPSI_AnyWordAndM1EqualsM0andM1
LPSPI Match Enabled.
-
enumerator kLPSI_MatchDisabled
-
enum _lpspi_pin_config
LPSPI pin (SDO and SDI) configuration.
Values:
-
enumerator kLPSPI_SdiInSdoOut
LPSPI SDI input, SDO output.
-
enumerator kLPSPI_SdiInSdiOut
LPSPI SDI input, SDI output.
-
enumerator kLPSPI_SdoInSdoOut
LPSPI SDO input, SDO output.
-
enumerator kLPSPI_SdoInSdiOut
LPSPI SDO input, SDI output.
-
enumerator kLPSPI_SdiInSdoOut
-
enum _lpspi_data_out_config
LPSPI data output configuration.
Values:
-
enumerator kLpspiDataOutRetained
Data out retains last value when chip select is de-asserted
-
enumerator kLpspiDataOutTristate
Data out is tristated when chip select is de-asserted
-
enumerator kLpspiDataOutRetained
-
enum _lpspi_transfer_width
LPSPI transfer width configuration.
Values:
-
enumerator kLPSPI_SingleBitXfer
1-bit shift at a time, data out on SDO, in on SDI (normal mode)
-
enumerator kLPSPI_TwoBitXfer
2-bits shift out on SDO/SDI and in on SDO/SDI
-
enumerator kLPSPI_FourBitXfer
4-bits shift out on SDO/SDI/PCS[3:2] and in on SDO/SDI/PCS[3:2]
-
enumerator kLPSPI_SingleBitXfer
-
enum _lpspi_delay_type
LPSPI delay type selection.
Values:
-
enumerator kLPSPI_PcsToSck
PCS-to-SCK delay.
-
enumerator kLPSPI_LastSckToPcs
Last SCK edge to PCS delay.
-
enumerator kLPSPI_BetweenTransfer
Delay between transfers.
-
enumerator kLPSPI_PcsToSck
-
enum _lpspi_transfer_config_flag_for_master
Use this enumeration for LPSPI master transfer configFlags.
Values:
-
enumerator kLPSPI_MasterPcs0
LPSPI master PCS shift macro , internal used. LPSPI master transfer use PCS0 signal
-
enumerator kLPSPI_MasterPcs1
LPSPI master PCS shift macro , internal used. LPSPI master transfer use PCS1 signal
-
enumerator kLPSPI_MasterPcs2
LPSPI master PCS shift macro , internal used. LPSPI master transfer use PCS2 signal
-
enumerator kLPSPI_MasterPcs3
LPSPI master PCS shift macro , internal used. LPSPI master transfer use PCS3 signal
-
enumerator kLPSPI_MasterPcsContinuous
Is PCS signal continuous
-
enumerator kLPSPI_MasterByteSwap
Is master swap the byte. For example, when want to send data 1 2 3 4 5 6 7 8 (suppose you set lpspi_shift_direction_t to MSB).
If you set bitPerFrame = 8 , no matter the kLPSPI_MasterByteSwapyou flag is used or not, the waveform is 1 2 3 4 5 6 7 8.
If you set bitPerFrame = 16 : (1) the waveform is 2 1 4 3 6 5 8 7 if you do not use the kLPSPI_MasterByteSwap flag. (2) the waveform is 1 2 3 4 5 6 7 8 if you use the kLPSPI_MasterByteSwap flag.
If you set bitPerFrame = 32 : (1) the waveform is 4 3 2 1 8 7 6 5 if you do not use the kLPSPI_MasterByteSwap flag. (2) the waveform is 1 2 3 4 5 6 7 8 if you use the kLPSPI_MasterByteSwap flag.
-
enumerator kLPSPI_MasterPcs0
-
enum _lpspi_transfer_config_flag_for_slave
Use this enumeration for LPSPI slave transfer configFlags.
Values:
-
enumerator kLPSPI_SlavePcs0
LPSPI slave PCS shift macro , internal used. LPSPI slave transfer use PCS0 signal
-
enumerator kLPSPI_SlavePcs1
LPSPI slave PCS shift macro , internal used. LPSPI slave transfer use PCS1 signal
-
enumerator kLPSPI_SlavePcs2
LPSPI slave PCS shift macro , internal used. LPSPI slave transfer use PCS2 signal
-
enumerator kLPSPI_SlavePcs3
LPSPI slave PCS shift macro , internal used. LPSPI slave transfer use PCS3 signal
-
enumerator kLPSPI_SlaveByteSwap
Is slave swap the byte. For example, when want to send data 1 2 3 4 5 6 7 8 (suppose you set lpspi_shift_direction_t to MSB).
If you set bitPerFrame = 8 , no matter the kLPSPI_SlaveByteSwap flag is used or not, the waveform is 1 2 3 4 5 6 7 8.
If you set bitPerFrame = 16 : (1) the waveform is 2 1 4 3 6 5 8 7 if you do not use the kLPSPI_SlaveByteSwap flag. (2) the waveform is 1 2 3 4 5 6 7 8 if you use the kLPSPI_SlaveByteSwap flag.
If you set bitPerFrame = 32 : (1) the waveform is 4 3 2 1 8 7 6 5 if you do not use the kLPSPI_SlaveByteSwap flag. (2) the waveform is 1 2 3 4 5 6 7 8 if you use the kLPSPI_SlaveByteSwap flag.
-
enumerator kLPSPI_SlavePcs0
-
enum _lpspi_transfer_state
LPSPI transfer state, which is used for LPSPI transactional API state machine.
Values:
-
enumerator kLPSPI_Idle
Nothing in the transmitter/receiver.
-
enumerator kLPSPI_Busy
Transfer queue is not finished.
-
enumerator kLPSPI_Error
Transfer error.
-
enumerator kLPSPI_Idle
-
typedef enum _lpspi_master_slave_mode lpspi_master_slave_mode_t
LPSPI master or slave mode configuration.
-
typedef enum _lpspi_which_pcs_config lpspi_which_pcs_t
LPSPI Peripheral Chip Select (PCS) configuration (which PCS to configure).
-
typedef enum _lpspi_pcs_polarity_config lpspi_pcs_polarity_config_t
LPSPI Peripheral Chip Select (PCS) Polarity configuration.
-
typedef enum _lpspi_clock_polarity lpspi_clock_polarity_t
LPSPI clock polarity configuration.
-
typedef enum _lpspi_clock_phase lpspi_clock_phase_t
LPSPI clock phase configuration.
-
typedef enum _lpspi_shift_direction lpspi_shift_direction_t
LPSPI data shifter direction options.
-
typedef enum _lpspi_host_request_select lpspi_host_request_select_t
LPSPI Host Request select configuration.
-
typedef enum _lpspi_match_config lpspi_match_config_t
LPSPI Match configuration options.
-
typedef enum _lpspi_pin_config lpspi_pin_config_t
LPSPI pin (SDO and SDI) configuration.
-
typedef enum _lpspi_data_out_config lpspi_data_out_config_t
LPSPI data output configuration.
-
typedef enum _lpspi_transfer_width lpspi_transfer_width_t
LPSPI transfer width configuration.
-
typedef enum _lpspi_delay_type lpspi_delay_type_t
LPSPI delay type selection.
-
typedef struct _lpspi_master_config lpspi_master_config_t
LPSPI master configuration structure.
-
typedef struct _lpspi_slave_config lpspi_slave_config_t
LPSPI slave configuration structure.
-
typedef struct _lpspi_master_handle lpspi_master_handle_t
Forward declaration of the _lpspi_master_handle typedefs.
-
typedef struct _lpspi_slave_handle lpspi_slave_handle_t
Forward declaration of the _lpspi_slave_handle typedefs.
-
typedef void (*lpspi_master_transfer_callback_t)(LPSPI_Type *base, lpspi_master_handle_t *handle, status_t status, void *userData)
Master completion callback function pointer type.
- Param base:
LPSPI peripheral address.
- Param handle:
Pointer to the handle for the LPSPI master.
- Param status:
Success or error code describing whether the transfer is completed.
- Param userData:
Arbitrary pointer-dataSized value passed from the application.
-
typedef void (*lpspi_slave_transfer_callback_t)(LPSPI_Type *base, lpspi_slave_handle_t *handle, status_t status, void *userData)
Slave completion callback function pointer type.
- Param base:
LPSPI peripheral address.
- Param handle:
Pointer to the handle for the LPSPI slave.
- Param status:
Success or error code describing whether the transfer is completed.
- Param userData:
Arbitrary pointer-dataSized value passed from the application.
-
typedef struct _lpspi_transfer lpspi_transfer_t
LPSPI master/slave transfer structure.
-
volatile uint8_t g_lpspiDummyData[]
Global variable for dummy data value setting.
-
LPSPI_DUMMY_DATA
LPSPI dummy data if no Tx data.
Dummy data used for tx if there is not txData.
-
SPI_RETRY_TIMES
Retry times for waiting flag.
-
LPSPI_MASTER_PCS_SHIFT
LPSPI master PCS shift macro , internal used.
-
LPSPI_MASTER_PCS_MASK
LPSPI master PCS shift macro , internal used.
-
LPSPI_SLAVE_PCS_SHIFT
LPSPI slave PCS shift macro , internal used.
-
LPSPI_SLAVE_PCS_MASK
LPSPI slave PCS shift macro , internal used.
-
struct _lpspi_master_config
- #include <fsl_lpspi.h>
LPSPI master configuration structure.
Public Members
-
uint32_t baudRate
Baud Rate for LPSPI.
-
uint32_t bitsPerFrame
Bits per frame, minimum 8, maximum 4096.
-
lpspi_clock_polarity_t cpol
Clock polarity.
-
lpspi_clock_phase_t cpha
Clock phase.
-
lpspi_shift_direction_t direction
MSB or LSB data shift direction.
-
uint32_t pcsToSckDelayInNanoSec
PCS to SCK delay time in nanoseconds, setting to 0 sets the minimum delay. It sets the boundary value if out of range.
-
uint32_t lastSckToPcsDelayInNanoSec
Last SCK to PCS delay time in nanoseconds, setting to 0 sets the minimum delay. It sets the boundary value if out of range.
-
uint32_t betweenTransferDelayInNanoSec
After the SCK delay time with nanoseconds, setting to 0 sets the minimum delay. It sets the boundary value if out of range.
-
lpspi_which_pcs_t whichPcs
Desired Peripheral Chip Select (PCS).
-
lpspi_pcs_polarity_config_t pcsActiveHighOrLow
Desired PCS active high or low
-
lpspi_pin_config_t pinCfg
Configures which pins are used for input and output data during single bit transfers.
-
lpspi_data_out_config_t dataOutConfig
Configures if the output data is tristated between accesses (LPSPI_PCS is negated).
-
bool enableInputDelay
Enable master to sample the input data on a delayed SCK. This can help improve slave setup time. Refer to device data sheet for specific time length.
-
uint32_t baudRate
-
struct _lpspi_slave_config
- #include <fsl_lpspi.h>
LPSPI slave configuration structure.
Public Members
-
uint32_t bitsPerFrame
Bits per frame, minimum 8, maximum 4096.
-
lpspi_clock_polarity_t cpol
Clock polarity.
-
lpspi_clock_phase_t cpha
Clock phase.
-
lpspi_shift_direction_t direction
MSB or LSB data shift direction.
-
lpspi_which_pcs_t whichPcs
Desired Peripheral Chip Select (pcs)
-
lpspi_pcs_polarity_config_t pcsActiveHighOrLow
Desired PCS active high or low
-
lpspi_pin_config_t pinCfg
Configures which pins are used for input and output data during single bit transfers.
-
lpspi_data_out_config_t dataOutConfig
Configures if the output data is tristated between accesses (LPSPI_PCS is negated).
-
uint32_t bitsPerFrame
-
struct _lpspi_transfer
- #include <fsl_lpspi.h>
LPSPI master/slave transfer structure.
Public Members
-
const uint8_t *txData
Send buffer.
-
uint8_t *rxData
Receive buffer.
-
volatile size_t dataSize
Transfer bytes.
-
uint32_t configFlags
Transfer transfer configuration flags. Set from _lpspi_transfer_config_flag_for_master if the transfer is used for master or _lpspi_transfer_config_flag_for_slave enumeration if the transfer is used for slave.
-
const uint8_t *txData
-
struct _lpspi_master_handle
- #include <fsl_lpspi.h>
LPSPI master transfer handle structure used for transactional API.
Public Members
-
volatile bool isPcsContinuous
Is PCS continuous in transfer.
-
volatile bool writeTcrInIsr
A flag that whether should write TCR in ISR.
-
volatile bool isByteSwap
A flag that whether should byte swap.
-
volatile bool isTxMask
A flag that whether TCR[TXMSK] is set.
-
volatile uint16_t bytesPerFrame
Number of bytes in each frame
-
volatile uint8_t fifoSize
FIFO dataSize.
-
volatile uint8_t rxWatermark
Rx watermark.
-
volatile uint8_t bytesEachWrite
Bytes for each write TDR.
-
volatile uint8_t bytesEachRead
Bytes for each read RDR.
-
const uint8_t *volatile txData
Send buffer.
-
uint8_t *volatile rxData
Receive buffer.
-
volatile size_t txRemainingByteCount
Number of bytes remaining to send.
-
volatile size_t rxRemainingByteCount
Number of bytes remaining to receive.
-
volatile uint32_t writeRegRemainingTimes
Write TDR register remaining times.
-
volatile uint32_t readRegRemainingTimes
Read RDR register remaining times.
-
uint32_t totalByteCount
Number of transfer bytes
-
uint32_t txBuffIfNull
Used if the txData is NULL.
-
volatile uint8_t state
LPSPI transfer state , _lpspi_transfer_state.
-
lpspi_master_transfer_callback_t callback
Completion callback.
-
void *userData
Callback user data.
-
volatile bool isPcsContinuous
-
struct _lpspi_slave_handle
- #include <fsl_lpspi.h>
LPSPI slave transfer handle structure used for transactional API.
Public Members
-
volatile bool isByteSwap
A flag that whether should byte swap.
-
volatile uint8_t fifoSize
FIFO dataSize.
-
volatile uint8_t rxWatermark
Rx watermark.
-
volatile uint8_t bytesEachWrite
Bytes for each write TDR.
-
volatile uint8_t bytesEachRead
Bytes for each read RDR.
-
const uint8_t *volatile txData
Send buffer.
-
uint8_t *volatile rxData
Receive buffer.
-
volatile size_t txRemainingByteCount
Number of bytes remaining to send.
-
volatile size_t rxRemainingByteCount
Number of bytes remaining to receive.
-
volatile uint32_t writeRegRemainingTimes
Write TDR register remaining times.
-
volatile uint32_t readRegRemainingTimes
Read RDR register remaining times.
-
uint32_t totalByteCount
Number of transfer bytes
-
volatile uint8_t state
LPSPI transfer state , _lpspi_transfer_state.
-
volatile uint32_t errorCount
Error count for slave transfer.
-
lpspi_slave_transfer_callback_t callback
Completion callback.
-
void *userData
Callback user data.
-
volatile bool isByteSwap
LPSPI eDMA Driver
-
FSL_LPSPI_EDMA_DRIVER_VERSION
LPSPI EDMA driver version.
-
DMA_MAX_TRANSFER_COUNT
DMA max transfer size.
-
typedef struct _lpspi_master_edma_handle lpspi_master_edma_handle_t
Forward declaration of the _lpspi_master_edma_handle typedefs.
-
typedef struct _lpspi_slave_edma_handle lpspi_slave_edma_handle_t
Forward declaration of the _lpspi_slave_edma_handle typedefs.
-
typedef void (*lpspi_master_edma_transfer_callback_t)(LPSPI_Type *base, lpspi_master_edma_handle_t *handle, status_t status, void *userData)
Completion callback function pointer type.
- Param base:
LPSPI peripheral base address.
- Param handle:
Pointer to the handle for the LPSPI master.
- Param status:
Success or error code describing whether the transfer completed.
- Param userData:
Arbitrary pointer-dataSized value passed from the application.
-
typedef void (*lpspi_slave_edma_transfer_callback_t)(LPSPI_Type *base, lpspi_slave_edma_handle_t *handle, status_t status, void *userData)
Completion callback function pointer type.
- Param base:
LPSPI peripheral base address.
- Param handle:
Pointer to the handle for the LPSPI slave.
- Param status:
Success or error code describing whether the transfer completed.
- Param userData:
Arbitrary pointer-dataSized value passed from the application.
-
void LPSPI_MasterTransferCreateHandleEDMA(LPSPI_Type *base, lpspi_master_edma_handle_t *handle, lpspi_master_edma_transfer_callback_t callback, void *userData, edma_handle_t *edmaRxRegToRxDataHandle, edma_handle_t *edmaTxDataToTxRegHandle)
Initializes the LPSPI master eDMA handle.
This function initializes the LPSPI eDMA handle which can be used for other LPSPI transactional APIs. Usually, for a specified LPSPI instance, call this API once to get the initialized handle.
Note that the LPSPI eDMA has a separated (Rx and Tx as two sources) or shared (Rx and Tx are the same source) DMA request source. (1) For a separated DMA request source, enable and set the Rx DMAMUX source for edmaRxRegToRxDataHandle and Tx DMAMUX source for edmaTxDataToTxRegHandle. (2) For a shared DMA request source, enable and set the Rx/Tx DMAMUX source for edmaRxRegToRxDataHandle.
- Parameters:
base – LPSPI peripheral base address.
handle – LPSPI handle pointer to lpspi_master_edma_handle_t.
callback – LPSPI callback.
userData – callback function parameter.
edmaRxRegToRxDataHandle – edmaRxRegToRxDataHandle pointer to edma_handle_t.
edmaTxDataToTxRegHandle – edmaTxDataToTxRegHandle pointer to edma_handle_t.
-
status_t LPSPI_MasterTransferEDMA(LPSPI_Type *base, lpspi_master_edma_handle_t *handle, lpspi_transfer_t *transfer)
LPSPI master transfer data using eDMA.
This function transfers data using eDMA. This is a non-blocking function, which returns right away. When all data is transferred, the callback function is called.
Note: The transfer data size should be an integer multiple of bytesPerFrame if bytesPerFrame is less than or equal to 4. For bytesPerFrame greater than 4: The transfer data size should be equal to bytesPerFrame if the bytesPerFrame is not an integer multiple of 4. Otherwise, the transfer data size can be an integer multiple of bytesPerFrame.
- Parameters:
base – LPSPI peripheral base address.
handle – pointer to lpspi_master_edma_handle_t structure which stores the transfer state.
transfer – pointer to lpspi_transfer_t structure.
- Returns:
status of status_t.
-
status_t LPSPI_MasterTransferPrepareEDMALite(LPSPI_Type *base, lpspi_master_edma_handle_t *handle, uint32_t configFlags)
LPSPI master config transfer parameter while using eDMA.
This function is preparing to transfer data using eDMA, work with LPSPI_MasterTransferEDMALite.
- Parameters:
base – LPSPI peripheral base address.
handle – pointer to lpspi_master_edma_handle_t structure which stores the transfer state.
configFlags – transfer configuration flags. _lpspi_transfer_config_flag_for_master.
- Return values:
kStatus_Success – Execution successfully.
kStatus_LPSPI_Busy – The LPSPI device is busy.
- Returns:
Indicates whether LPSPI master transfer was successful or not.
-
status_t LPSPI_MasterTransferEDMALite(LPSPI_Type *base, lpspi_master_edma_handle_t *handle, lpspi_transfer_t *transfer)
LPSPI master transfer data using eDMA without configs.
This function transfers data using eDMA. This is a non-blocking function, which returns right away. When all data is transferred, the callback function is called.
Note: This API is only for transfer through DMA without configuration. Before calling this API, you must call LPSPI_MasterTransferPrepareEDMALite to configure it once. The transfer data size should be an integer multiple of bytesPerFrame if bytesPerFrame is less than or equal to 4. For bytesPerFrame greater than 4: The transfer data size should be equal to bytesPerFrame if the bytesPerFrame is not an integer multiple of 4. Otherwise, the transfer data size can be an integer multiple of bytesPerFrame.
- Parameters:
base – LPSPI peripheral base address.
handle – pointer to lpspi_master_edma_handle_t structure which stores the transfer state.
transfer – pointer to lpspi_transfer_t structure, config field is not uesed.
- Return values:
kStatus_Success – Execution successfully.
kStatus_LPSPI_Busy – The LPSPI device is busy.
kStatus_InvalidArgument – The transfer structure is invalid.
- Returns:
Indicates whether LPSPI master transfer was successful or not.
-
void LPSPI_MasterTransferAbortEDMA(LPSPI_Type *base, lpspi_master_edma_handle_t *handle)
LPSPI master aborts a transfer which is using eDMA.
This function aborts a transfer which is using eDMA.
- Parameters:
base – LPSPI peripheral base address.
handle – pointer to lpspi_master_edma_handle_t structure which stores the transfer state.
-
status_t LPSPI_MasterTransferGetCountEDMA(LPSPI_Type *base, lpspi_master_edma_handle_t *handle, size_t *count)
Gets the master eDMA transfer remaining bytes.
This function gets the master eDMA transfer remaining bytes.
- Parameters:
base – LPSPI peripheral base address.
handle – pointer to lpspi_master_edma_handle_t structure which stores the transfer state.
count – Number of bytes transferred so far by the EDMA transaction.
- Returns:
status of status_t.
-
void LPSPI_SlaveTransferCreateHandleEDMA(LPSPI_Type *base, lpspi_slave_edma_handle_t *handle, lpspi_slave_edma_transfer_callback_t callback, void *userData, edma_handle_t *edmaRxRegToRxDataHandle, edma_handle_t *edmaTxDataToTxRegHandle)
Initializes the LPSPI slave eDMA handle.
This function initializes the LPSPI eDMA handle which can be used for other LPSPI transactional APIs. Usually, for a specified LPSPI instance, call this API once to get the initialized handle.
Note that LPSPI eDMA has a separated (Rx and Tx as two sources) or shared (Rx and Tx as the same source) DMA request source.
(1) For a separated DMA request source, enable and set the Rx DMAMUX source for edmaRxRegToRxDataHandle and Tx DMAMUX source for edmaTxDataToTxRegHandle. (2) For a shared DMA request source, enable and set the Rx/Rx DMAMUX source for edmaRxRegToRxDataHandle .
- Parameters:
base – LPSPI peripheral base address.
handle – LPSPI handle pointer to lpspi_slave_edma_handle_t.
callback – LPSPI callback.
userData – callback function parameter.
edmaRxRegToRxDataHandle – edmaRxRegToRxDataHandle pointer to edma_handle_t.
edmaTxDataToTxRegHandle – edmaTxDataToTxRegHandle pointer to edma_handle_t.
-
status_t LPSPI_SlaveTransferEDMA(LPSPI_Type *base, lpspi_slave_edma_handle_t *handle, lpspi_transfer_t *transfer)
LPSPI slave transfers data using eDMA.
This function transfers data using eDMA. This is a non-blocking function, which return right away. When all data is transferred, the callback function is called.
Note: The transfer data size should be an integer multiple of bytesPerFrame if bytesPerFrame is less than or equal to 4. For bytesPerFrame greater than 4: The transfer data size should be equal to bytesPerFrame if the bytesPerFrame is not an integer multiple of 4. Otherwise, the transfer data size can be an integer multiple of bytesPerFrame.
- Parameters:
base – LPSPI peripheral base address.
handle – pointer to lpspi_slave_edma_handle_t structure which stores the transfer state.
transfer – pointer to lpspi_transfer_t structure.
- Returns:
status of status_t.
-
void LPSPI_SlaveTransferAbortEDMA(LPSPI_Type *base, lpspi_slave_edma_handle_t *handle)
LPSPI slave aborts a transfer which is using eDMA.
This function aborts a transfer which is using eDMA.
- Parameters:
base – LPSPI peripheral base address.
handle – pointer to lpspi_slave_edma_handle_t structure which stores the transfer state.
-
status_t LPSPI_SlaveTransferGetCountEDMA(LPSPI_Type *base, lpspi_slave_edma_handle_t *handle, size_t *count)
Gets the slave eDMA transfer remaining bytes.
This function gets the slave eDMA transfer remaining bytes.
- Parameters:
base – LPSPI peripheral base address.
handle – pointer to lpspi_slave_edma_handle_t structure which stores the transfer state.
count – Number of bytes transferred so far by the eDMA transaction.
- Returns:
status of status_t.
-
struct _lpspi_master_edma_handle
- #include <fsl_lpspi_edma.h>
LPSPI master eDMA transfer handle structure used for transactional API.
Public Members
-
volatile bool isPcsContinuous
Is PCS continuous in transfer.
-
volatile bool isByteSwap
A flag that whether should byte swap.
-
volatile uint8_t fifoSize
FIFO dataSize.
-
volatile uint8_t rxWatermark
Rx watermark.
-
volatile uint8_t bytesEachWrite
Bytes for each write TDR.
-
volatile uint8_t bytesEachRead
Bytes for each read RDR.
-
volatile uint8_t bytesLastRead
Bytes for last read RDR.
-
volatile bool isThereExtraRxBytes
Is there extra RX byte.
-
const uint8_t *volatile txData
Send buffer.
-
uint8_t *volatile rxData
Receive buffer.
-
volatile size_t txRemainingByteCount
Number of bytes remaining to send.
-
volatile size_t rxRemainingByteCount
Number of bytes remaining to receive.
-
volatile uint32_t writeRegRemainingTimes
Write TDR register remaining times.
-
volatile uint32_t readRegRemainingTimes
Read RDR register remaining times.
-
uint32_t totalByteCount
Number of transfer bytes
-
edma_tcd_t *lastTimeTCD
Pointer to the lastTime TCD
-
bool isMultiDMATransmit
Is there multi DMA transmit
-
volatile uint8_t dmaTransmitTime
DMA Transfer times.
-
uint32_t lastTimeDataBytes
DMA transmit last Time data Bytes
-
uint32_t dataBytesEveryTime
Bytes in a time for DMA transfer, default is DMA_MAX_TRANSFER_COUNT
-
edma_transfer_config_t transferConfigRx
Config of DMA rx channel.
-
edma_transfer_config_t transferConfigTx
Config of DMA tx channel.
-
uint32_t txBuffIfNull
Used if there is not txData for DMA purpose.
-
uint32_t rxBuffIfNull
Used if there is not rxData for DMA purpose.
-
uint32_t transmitCommand
Used to write TCR for DMA purpose.
-
volatile uint8_t state
LPSPI transfer state , _lpspi_transfer_state.
-
uint8_t nbytes
eDMA minor byte transfer count initially configured.
-
lpspi_master_edma_transfer_callback_t callback
Completion callback.
-
void *userData
Callback user data.
-
edma_handle_t *edmaRxRegToRxDataHandle
edma_handle_t handle point used for RxReg to RxData buff
-
edma_handle_t *edmaTxDataToTxRegHandle
edma_handle_t handle point used for TxData to TxReg buff
-
edma_tcd_t lpspiSoftwareTCD[3]
SoftwareTCD, internal used
-
volatile bool isPcsContinuous
-
struct _lpspi_slave_edma_handle
- #include <fsl_lpspi_edma.h>
LPSPI slave eDMA transfer handle structure used for transactional API.
Public Members
-
volatile bool isByteSwap
A flag that whether should byte swap.
-
volatile uint8_t fifoSize
FIFO dataSize.
-
volatile uint8_t rxWatermark
Rx watermark.
-
volatile uint8_t bytesEachWrite
Bytes for each write TDR.
-
volatile uint8_t bytesEachRead
Bytes for each read RDR.
-
volatile uint8_t bytesLastRead
Bytes for last read RDR.
-
volatile bool isThereExtraRxBytes
Is there extra RX byte.
-
uint8_t nbytes
eDMA minor byte transfer count initially configured.
-
const uint8_t *volatile txData
Send buffer.
-
uint8_t *volatile rxData
Receive buffer.
-
volatile size_t txRemainingByteCount
Number of bytes remaining to send.
-
volatile size_t rxRemainingByteCount
Number of bytes remaining to receive.
-
volatile uint32_t writeRegRemainingTimes
Write TDR register remaining times.
-
volatile uint32_t readRegRemainingTimes
Read RDR register remaining times.
-
uint32_t totalByteCount
Number of transfer bytes
-
uint32_t txBuffIfNull
Used if there is not txData for DMA purpose.
-
uint32_t rxBuffIfNull
Used if there is not rxData for DMA purpose.
-
volatile uint8_t state
LPSPI transfer state.
-
uint32_t errorCount
Error count for slave transfer.
-
lpspi_slave_edma_transfer_callback_t callback
Completion callback.
-
void *userData
Callback user data.
-
edma_handle_t *edmaRxRegToRxDataHandle
edma_handle_t handle point used for RxReg to RxData buff
-
edma_handle_t *edmaTxDataToTxRegHandle
edma_handle_t handle point used for TxData to TxReg
-
edma_tcd_t lpspiSoftwareTCD[2]
SoftwareTCD, internal used
-
volatile bool isByteSwap
LPUART: Low Power Universal Asynchronous Receiver/Transmitter Driver
LPUART Driver
-
static inline void LPUART_SoftwareReset(LPUART_Type *base)
Resets the LPUART using software.
This function resets all internal logic and registers except the Global Register. Remains set until cleared by software.
- Parameters:
base – LPUART peripheral base address.
-
status_t LPUART_Init(LPUART_Type *base, const lpuart_config_t *config, uint32_t srcClock_Hz)
Initializes an LPUART instance with the user configuration structure and the peripheral clock.
This function configures the LPUART module with user-defined settings. Call the LPUART_GetDefaultConfig() function to configure the configuration structure and get the default configuration. The example below shows how to use this API to configure the LPUART.
lpuart_config_t lpuartConfig; lpuartConfig.baudRate_Bps = 115200U; lpuartConfig.parityMode = kLPUART_ParityDisabled; lpuartConfig.dataBitsCount = kLPUART_EightDataBits; lpuartConfig.isMsb = false; lpuartConfig.stopBitCount = kLPUART_OneStopBit; lpuartConfig.txFifoWatermark = 0; lpuartConfig.rxFifoWatermark = 1; LPUART_Init(LPUART1, &lpuartConfig, 20000000U);
- Parameters:
base – LPUART peripheral base address.
config – Pointer to a user-defined configuration structure.
srcClock_Hz – LPUART clock source frequency in HZ.
- Return values:
kStatus_LPUART_BaudrateNotSupport – Baudrate is not support in current clock source.
kStatus_Success – LPUART initialize succeed
-
void LPUART_Deinit(LPUART_Type *base)
Deinitializes a LPUART instance.
This function waits for transmit to complete, disables TX and RX, and disables the LPUART clock.
- Parameters:
base – LPUART peripheral base address.
-
void LPUART_GetDefaultConfig(lpuart_config_t *config)
Gets the default configuration structure.
This function initializes the LPUART configuration structure to a default value. The default values are: lpuartConfig->baudRate_Bps = 115200U; lpuartConfig->parityMode = kLPUART_ParityDisabled; lpuartConfig->dataBitsCount = kLPUART_EightDataBits; lpuartConfig->isMsb = false; lpuartConfig->stopBitCount = kLPUART_OneStopBit; lpuartConfig->txFifoWatermark = 0; lpuartConfig->rxFifoWatermark = 1; lpuartConfig->rxIdleType = kLPUART_IdleTypeStartBit; lpuartConfig->rxIdleConfig = kLPUART_IdleCharacter1; lpuartConfig->enableTx = false; lpuartConfig->enableRx = false;
- Parameters:
config – Pointer to a configuration structure.
-
status_t LPUART_SetBaudRate(LPUART_Type *base, uint32_t baudRate_Bps, uint32_t srcClock_Hz)
Sets the LPUART instance baudrate.
This function configures the LPUART module baudrate. This function is used to update the LPUART module baudrate after the LPUART module is initialized by the LPUART_Init.
LPUART_SetBaudRate(LPUART1, 115200U, 20000000U);
- Parameters:
base – LPUART peripheral base address.
baudRate_Bps – LPUART baudrate to be set.
srcClock_Hz – LPUART clock source frequency in HZ.
- Return values:
kStatus_LPUART_BaudrateNotSupport – Baudrate is not supported in the current clock source.
kStatus_Success – Set baudrate succeeded.
-
void LPUART_Enable9bitMode(LPUART_Type *base, bool enable)
Enable 9-bit data mode for LPUART.
This function set the 9-bit mode for LPUART module. The 9th bit is not used for parity thus can be modified by user.
- Parameters:
base – LPUART peripheral base address.
enable – true to enable, flase to disable.
-
static inline void LPUART_SetMatchAddress(LPUART_Type *base, uint16_t address1, uint16_t address2)
Set the LPUART address.
This function configures the address for LPUART module that works as slave in 9-bit data mode. One or two address fields can be configured. When the address field’s match enable bit is set, the frame it receices with MSB being 1 is considered as an address frame, otherwise it is considered as data frame. Once the address frame matches one of slave’s own addresses, this slave is addressed. This address frame and its following data frames are stored in the receive buffer, otherwise the frames will be discarded. To un-address a slave, just send an address frame with unmatched address.
Note
Any LPUART instance joined in the multi-slave system can work as slave. The position of the address mark is the same as the parity bit when parity is enabled for 8 bit and 9 bit data formats.
- Parameters:
base – LPUART peripheral base address.
address1 – LPUART slave address1.
address2 – LPUART slave address2.
-
static inline void LPUART_EnableMatchAddress(LPUART_Type *base, bool match1, bool match2)
Enable the LPUART match address feature.
- Parameters:
base – LPUART peripheral base address.
match1 – true to enable match address1, false to disable.
match2 – true to enable match address2, false to disable.
-
static inline void LPUART_SetRxFifoWatermark(LPUART_Type *base, uint8_t water)
Sets the rx FIFO watermark.
- Parameters:
base – LPUART peripheral base address.
water – Rx FIFO watermark.
-
static inline void LPUART_SetTxFifoWatermark(LPUART_Type *base, uint8_t water)
Sets the tx FIFO watermark.
- Parameters:
base – LPUART peripheral base address.
water – Tx FIFO watermark.
-
static inline void LPUART_TransferEnable16Bit(lpuart_handle_t *handle, bool enable)
Sets the LPUART using 16bit transmit, only for 9bit or 10bit mode.
This function Enable 16bit Data transmit in lpuart_handle_t.
- Parameters:
handle – LPUART handle pointer.
enable – true to enable, false to disable.
-
uint32_t LPUART_GetStatusFlags(LPUART_Type *base)
Gets LPUART status flags.
This function gets all LPUART status flags. The flags are returned as the logical OR value of the enumerators _lpuart_flags. To check for a specific status, compare the return value with enumerators in the _lpuart_flags. For example, to check whether the TX is empty:
if (kLPUART_TxDataRegEmptyFlag & LPUART_GetStatusFlags(LPUART1)) { ... }
- Parameters:
base – LPUART peripheral base address.
- Returns:
LPUART status flags which are ORed by the enumerators in the _lpuart_flags.
-
status_t LPUART_ClearStatusFlags(LPUART_Type *base, uint32_t mask)
Clears status flags with a provided mask.
This function clears LPUART status flags with a provided mask. Automatically cleared flags can’t be cleared by this function. Flags that can only cleared or set by hardware are: kLPUART_TxDataRegEmptyFlag, kLPUART_TransmissionCompleteFlag, kLPUART_RxDataRegFullFlag, kLPUART_RxActiveFlag, kLPUART_NoiseErrorFlag, kLPUART_ParityErrorFlag, kLPUART_TxFifoEmptyFlag,kLPUART_RxFifoEmptyFlag Note: This API should be called when the Tx/Rx is idle, otherwise it takes no effects.
- Parameters:
base – LPUART peripheral base address.
mask – the status flags to be cleared. The user can use the enumerators in the _lpuart_status_flag_t to do the OR operation and get the mask.
- Return values:
kStatus_LPUART_FlagCannotClearManually – The flag can’t be cleared by this function but it is cleared automatically by hardware.
kStatus_Success – Status in the mask are cleared.
- Returns:
0 succeed, others failed.
-
void LPUART_EnableInterrupts(LPUART_Type *base, uint32_t mask)
Enables LPUART interrupts according to a provided mask.
This function enables the LPUART interrupts according to a provided mask. The mask is a logical OR of enumeration members. See the _lpuart_interrupt_enable. This examples shows how to enable TX empty interrupt and RX full interrupt:
LPUART_EnableInterrupts(LPUART1,kLPUART_TxDataRegEmptyInterruptEnable | kLPUART_RxDataRegFullInterruptEnable);
- Parameters:
base – LPUART peripheral base address.
mask – The interrupts to enable. Logical OR of _lpuart_interrupt_enable.
-
void LPUART_DisableInterrupts(LPUART_Type *base, uint32_t mask)
Disables LPUART interrupts according to a provided mask.
This function disables the LPUART interrupts according to a provided mask. The mask is a logical OR of enumeration members. See _lpuart_interrupt_enable. This example shows how to disable the TX empty interrupt and RX full interrupt:
LPUART_DisableInterrupts(LPUART1,kLPUART_TxDataRegEmptyInterruptEnable | kLPUART_RxDataRegFullInterruptEnable);
- Parameters:
base – LPUART peripheral base address.
mask – The interrupts to disable. Logical OR of _lpuart_interrupt_enable.
-
uint32_t LPUART_GetEnabledInterrupts(LPUART_Type *base)
Gets enabled LPUART interrupts.
This function gets the enabled LPUART interrupts. The enabled interrupts are returned as the logical OR value of the enumerators _lpuart_interrupt_enable. To check a specific interrupt enable status, compare the return value with enumerators in _lpuart_interrupt_enable. For example, to check whether the TX empty interrupt is enabled:
uint32_t enabledInterrupts = LPUART_GetEnabledInterrupts(LPUART1); if (kLPUART_TxDataRegEmptyInterruptEnable & enabledInterrupts) { ... }
- Parameters:
base – LPUART peripheral base address.
- Returns:
LPUART interrupt flags which are logical OR of the enumerators in _lpuart_interrupt_enable.
-
static inline uintptr_t LPUART_GetDataRegisterAddress(LPUART_Type *base)
Gets the LPUART data register address.
This function returns the LPUART data register address, which is mainly used by the DMA/eDMA.
- Parameters:
base – LPUART peripheral base address.
- Returns:
LPUART data register addresses which are used both by the transmitter and receiver.
-
static inline void LPUART_EnableTxDMA(LPUART_Type *base, bool enable)
Enables or disables the LPUART transmitter DMA request.
This function enables or disables the transmit data register empty flag, STAT[TDRE], to generate DMA requests.
- Parameters:
base – LPUART peripheral base address.
enable – True to enable, false to disable.
-
static inline void LPUART_EnableRxDMA(LPUART_Type *base, bool enable)
Enables or disables the LPUART receiver DMA.
This function enables or disables the receiver data register full flag, STAT[RDRF], to generate DMA requests.
- Parameters:
base – LPUART peripheral base address.
enable – True to enable, false to disable.
-
uint32_t LPUART_GetInstance(LPUART_Type *base)
Get the LPUART instance from peripheral base address.
- Parameters:
base – LPUART peripheral base address.
- Returns:
LPUART instance.
-
static inline void LPUART_EnableTx(LPUART_Type *base, bool enable)
Enables or disables the LPUART transmitter.
This function enables or disables the LPUART transmitter.
- Parameters:
base – LPUART peripheral base address.
enable – True to enable, false to disable.
-
static inline void LPUART_EnableRx(LPUART_Type *base, bool enable)
Enables or disables the LPUART receiver.
This function enables or disables the LPUART receiver.
- Parameters:
base – LPUART peripheral base address.
enable – True to enable, false to disable.
-
static inline void LPUART_WriteByte(LPUART_Type *base, uint8_t data)
Writes to the transmitter register.
This function writes data to the transmitter register directly. The upper layer must ensure that the TX register is empty or that the TX FIFO has room before calling this function.
- Parameters:
base – LPUART peripheral base address.
data – Data write to the TX register.
-
static inline uint8_t LPUART_ReadByte(LPUART_Type *base)
Reads the receiver register.
This function reads data from the receiver register directly. The upper layer must ensure that the receiver register is full or that the RX FIFO has data before calling this function.
- Parameters:
base – LPUART peripheral base address.
- Returns:
Data read from data register.
-
static inline uint8_t LPUART_GetRxFifoCount(LPUART_Type *base)
Gets the rx FIFO data count.
- Parameters:
base – LPUART peripheral base address.
- Returns:
rx FIFO data count.
-
static inline uint8_t LPUART_GetTxFifoCount(LPUART_Type *base)
Gets the tx FIFO data count.
- Parameters:
base – LPUART peripheral base address.
- Returns:
tx FIFO data count.
-
void LPUART_SendAddress(LPUART_Type *base, uint8_t address)
Transmit an address frame in 9-bit data mode.
- Parameters:
base – LPUART peripheral base address.
address – LPUART slave address.
-
status_t LPUART_WriteBlocking(LPUART_Type *base, const uint8_t *data, size_t length)
Writes to the transmitter register using a blocking method.
This function polls the transmitter register, first waits for the register to be empty or TX FIFO to have room, and writes data to the transmitter buffer, then waits for the dat to be sent out to the bus.
- Parameters:
base – LPUART peripheral base address.
data – Start address of the data to write.
length – Size of the data to write.
- Return values:
kStatus_LPUART_Timeout – Transmission timed out and was aborted.
kStatus_Success – Successfully wrote all data.
-
status_t LPUART_WriteBlocking16bit(LPUART_Type *base, const uint16_t *data, size_t length)
Writes to the transmitter register using a blocking method in 9bit or 10bit mode.
Note
This function only support 9bit or 10bit transfer. Please make sure only 10bit of data is valid and other bits are 0.
- Parameters:
base – LPUART peripheral base address.
data – Start address of the data to write.
length – Size of the data to write.
- Return values:
kStatus_LPUART_Timeout – Transmission timed out and was aborted.
kStatus_Success – Successfully wrote all data.
-
status_t LPUART_ReadBlocking(LPUART_Type *base, uint8_t *data, size_t length)
Reads the receiver data register using a blocking method.
This function polls the receiver register, waits for the receiver register full or receiver FIFO has data, and reads data from the TX register.
- Parameters:
base – LPUART peripheral base address.
data – Start address of the buffer to store the received data.
length – Size of the buffer.
- Return values:
kStatus_LPUART_RxHardwareOverrun – Receiver overrun happened while receiving data.
kStatus_LPUART_NoiseError – Noise error happened while receiving data.
kStatus_LPUART_FramingError – Framing error happened while receiving data.
kStatus_LPUART_ParityError – Parity error happened while receiving data.
kStatus_LPUART_Timeout – Transmission timed out and was aborted.
kStatus_Success – Successfully received all data.
-
status_t LPUART_ReadBlocking16bit(LPUART_Type *base, uint16_t *data, size_t length)
Reads the receiver data register in 9bit or 10bit mode.
Note
This function only support 9bit or 10bit transfer.
- Parameters:
base – LPUART peripheral base address.
data – Start address of the buffer to store the received data by 16bit, only 10bit is valid.
length – Size of the buffer.
- Return values:
kStatus_LPUART_RxHardwareOverrun – Receiver overrun happened while receiving data.
kStatus_LPUART_NoiseError – Noise error happened while receiving data.
kStatus_LPUART_FramingError – Framing error happened while receiving data.
kStatus_LPUART_ParityError – Parity error happened while receiving data.
kStatus_LPUART_Timeout – Transmission timed out and was aborted.
kStatus_Success – Successfully received all data.
-
void LPUART_TransferCreateHandle(LPUART_Type *base, lpuart_handle_t *handle, lpuart_transfer_callback_t callback, void *userData)
Initializes the LPUART handle.
This function initializes the LPUART handle, which can be used for other LPUART transactional APIs. Usually, for a specified LPUART instance, call this API once to get the initialized handle.
The LPUART driver supports the “background” receiving, which means that user can set up an RX ring buffer optionally. Data received is stored into the ring buffer even when the user doesn’t call the LPUART_TransferReceiveNonBlocking() API. If there is already data received in the ring buffer, the user can get the received data from the ring buffer directly. The ring buffer is disabled if passing NULL as
ringBuffer
.- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
callback – Callback function.
userData – User data.
-
status_t LPUART_TransferSendNonBlocking(LPUART_Type *base, lpuart_handle_t *handle, lpuart_transfer_t *xfer)
Transmits a buffer of data using the interrupt method.
This function send data using an interrupt method. This is a non-blocking function, which returns directly without waiting for all data written to the transmitter register. When all data is written to the TX register in the ISR, the LPUART driver calls the callback function and passes the kStatus_LPUART_TxIdle as status parameter.
Note
The kStatus_LPUART_TxIdle is passed to the upper layer when all data are written to the TX register. However, there is no check to ensure that all the data sent out. Before disabling the TX, check the kLPUART_TransmissionCompleteFlag to ensure that the transmit is finished.
- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
xfer – LPUART transfer structure, see lpuart_transfer_t.
- Return values:
kStatus_Success – Successfully start the data transmission.
kStatus_LPUART_TxBusy – Previous transmission still not finished, data not all written to the TX register.
kStatus_InvalidArgument – Invalid argument.
-
void LPUART_TransferStartRingBuffer(LPUART_Type *base, lpuart_handle_t *handle, uint8_t *ringBuffer, size_t ringBufferSize)
Sets up the RX ring buffer.
This function sets up the RX ring buffer to a specific UART handle.
When the RX ring buffer is used, data received is stored into the ring buffer even when the user doesn’t call the UART_TransferReceiveNonBlocking() API. If there is already data received in the ring buffer, the user can get the received data from the ring buffer directly.
Note
When using RX ring buffer, one byte is reserved for internal use. In other words, if
ringBufferSize
is 32, then only 31 bytes are used for saving data.- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
ringBuffer – Start address of ring buffer for background receiving. Pass NULL to disable the ring buffer.
ringBufferSize – size of the ring buffer.
-
void LPUART_TransferStopRingBuffer(LPUART_Type *base, lpuart_handle_t *handle)
Aborts the background transfer and uninstalls the ring buffer.
This function aborts the background transfer and uninstalls the ring buffer.
- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
-
size_t LPUART_TransferGetRxRingBufferLength(LPUART_Type *base, lpuart_handle_t *handle)
Get the length of received data in RX ring buffer.
- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
- Returns:
Length of received data in RX ring buffer.
-
void LPUART_TransferAbortSend(LPUART_Type *base, lpuart_handle_t *handle)
Aborts the interrupt-driven data transmit.
This function aborts the interrupt driven data sending. The user can get the remainBtyes to find out how many bytes are not sent out.
- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
-
status_t LPUART_TransferGetSendCount(LPUART_Type *base, lpuart_handle_t *handle, uint32_t *count)
Gets the number of bytes that have been sent out to bus.
This function gets the number of bytes that have been sent out to bus by an interrupt method.
- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
count – Send bytes count.
- Return values:
kStatus_NoTransferInProgress – No send in progress.
kStatus_InvalidArgument – Parameter is invalid.
kStatus_Success – Get successfully through the parameter
count
;
-
status_t LPUART_TransferReceiveNonBlocking(LPUART_Type *base, lpuart_handle_t *handle, lpuart_transfer_t *xfer, size_t *receivedBytes)
Receives a buffer of data using the interrupt method.
This function receives data using an interrupt method. This is a non-blocking function which returns without waiting to ensure that all data are received. If the RX ring buffer is used and not empty, the data in the ring buffer is copied and the parameter
receivedBytes
shows how many bytes are copied from the ring buffer. After copying, if the data in the ring buffer is not enough for read, the receive request is saved by the LPUART driver. When the new data arrives, the receive request is serviced first. When all data is received, the LPUART driver notifies the upper layer through a callback function and passes a status parameter kStatus_UART_RxIdle. For example, the upper layer needs 10 bytes but there are only 5 bytes in ring buffer. The 5 bytes are copied to xfer->data, which returns with the parameterreceivedBytes
set to 5. For the remaining 5 bytes, the newly arrived data is saved from xfer->data[5]. When 5 bytes are received, the LPUART driver notifies the upper layer. If the RX ring buffer is not enabled, this function enables the RX and RX interrupt to receive data to xfer->data. When all data is received, the upper layer is notified.- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
xfer – LPUART transfer structure, see uart_transfer_t.
receivedBytes – Bytes received from the ring buffer directly.
- Return values:
kStatus_Success – Successfully queue the transfer into the transmit queue.
kStatus_LPUART_RxBusy – Previous receive request is not finished.
kStatus_InvalidArgument – Invalid argument.
-
void LPUART_TransferAbortReceive(LPUART_Type *base, lpuart_handle_t *handle)
Aborts the interrupt-driven data receiving.
This function aborts the interrupt-driven data receiving. The user can get the remainBytes to find out how many bytes not received yet.
- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
-
status_t LPUART_TransferGetReceiveCount(LPUART_Type *base, lpuart_handle_t *handle, uint32_t *count)
Gets the number of bytes that have been received.
This function gets the number of bytes that have been received.
- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
count – Receive bytes count.
- Return values:
kStatus_NoTransferInProgress – No receive in progress.
kStatus_InvalidArgument – Parameter is invalid.
kStatus_Success – Get successfully through the parameter
count
;
-
void LPUART_TransferHandleIRQ(LPUART_Type *base, void *irqHandle)
LPUART IRQ handle function.
This function handles the LPUART transmit and receive IRQ request.
- Parameters:
base – LPUART peripheral base address.
irqHandle – LPUART handle pointer.
-
void LPUART_TransferHandleErrorIRQ(LPUART_Type *base, void *irqHandle)
LPUART Error IRQ handle function.
This function handles the LPUART error IRQ request.
- Parameters:
base – LPUART peripheral base address.
irqHandle – LPUART handle pointer.
-
FSL_LPUART_DRIVER_VERSION
LPUART driver version.
Error codes for the LPUART driver.
Values:
-
enumerator kStatus_LPUART_TxBusy
TX busy
-
enumerator kStatus_LPUART_RxBusy
RX busy
-
enumerator kStatus_LPUART_TxIdle
LPUART transmitter is idle.
-
enumerator kStatus_LPUART_RxIdle
LPUART receiver is idle.
-
enumerator kStatus_LPUART_TxWatermarkTooLarge
TX FIFO watermark too large
-
enumerator kStatus_LPUART_RxWatermarkTooLarge
RX FIFO watermark too large
-
enumerator kStatus_LPUART_FlagCannotClearManually
Some flag can’t manually clear
-
enumerator kStatus_LPUART_Error
Error happens on LPUART.
-
enumerator kStatus_LPUART_RxRingBufferOverrun
LPUART RX software ring buffer overrun.
-
enumerator kStatus_LPUART_RxHardwareOverrun
LPUART RX receiver overrun.
-
enumerator kStatus_LPUART_NoiseError
LPUART noise error.
-
enumerator kStatus_LPUART_FramingError
LPUART framing error.
-
enumerator kStatus_LPUART_ParityError
LPUART parity error.
-
enumerator kStatus_LPUART_BaudrateNotSupport
Baudrate is not support in current clock source
-
enumerator kStatus_LPUART_IdleLineDetected
IDLE flag.
-
enumerator kStatus_LPUART_Timeout
LPUART times out.
-
enumerator kStatus_LPUART_TxBusy
-
enum _lpuart_parity_mode
LPUART parity mode.
Values:
-
enumerator kLPUART_ParityDisabled
Parity disabled
-
enumerator kLPUART_ParityEven
Parity enabled, type even, bit setting: PE|PT = 10
-
enumerator kLPUART_ParityOdd
Parity enabled, type odd, bit setting: PE|PT = 11
-
enumerator kLPUART_ParityDisabled
-
enum _lpuart_data_bits
LPUART data bits count.
Values:
-
enumerator kLPUART_EightDataBits
Eight data bit
-
enumerator kLPUART_SevenDataBits
Seven data bit
-
enumerator kLPUART_EightDataBits
-
enum _lpuart_stop_bit_count
LPUART stop bit count.
Values:
-
enumerator kLPUART_OneStopBit
One stop bit
-
enumerator kLPUART_TwoStopBit
Two stop bits
-
enumerator kLPUART_OneStopBit
-
enum _lpuart_transmit_cts_source
LPUART transmit CTS source.
Values:
-
enumerator kLPUART_CtsSourcePin
CTS resource is the LPUART_CTS pin.
-
enumerator kLPUART_CtsSourceMatchResult
CTS resource is the match result.
-
enumerator kLPUART_CtsSourcePin
-
enum _lpuart_transmit_cts_config
LPUART transmit CTS configure.
Values:
-
enumerator kLPUART_CtsSampleAtStart
CTS input is sampled at the start of each character.
-
enumerator kLPUART_CtsSampleAtIdle
CTS input is sampled when the transmitter is idle
-
enumerator kLPUART_CtsSampleAtStart
-
enum _lpuart_idle_type_select
LPUART idle flag type defines when the receiver starts counting.
Values:
-
enumerator kLPUART_IdleTypeStartBit
Start counting after a valid start bit.
-
enumerator kLPUART_IdleTypeStopBit
Start counting after a stop bit.
-
enumerator kLPUART_IdleTypeStartBit
-
enum _lpuart_idle_config
LPUART idle detected configuration. This structure defines the number of idle characters that must be received before the IDLE flag is set.
Values:
-
enumerator kLPUART_IdleCharacter1
the number of idle characters.
-
enumerator kLPUART_IdleCharacter2
the number of idle characters.
-
enumerator kLPUART_IdleCharacter4
the number of idle characters.
-
enumerator kLPUART_IdleCharacter8
the number of idle characters.
-
enumerator kLPUART_IdleCharacter16
the number of idle characters.
-
enumerator kLPUART_IdleCharacter32
the number of idle characters.
-
enumerator kLPUART_IdleCharacter64
the number of idle characters.
-
enumerator kLPUART_IdleCharacter128
the number of idle characters.
-
enumerator kLPUART_IdleCharacter1
-
enum _lpuart_interrupt_enable
LPUART interrupt configuration structure, default settings all disabled.
This structure contains the settings for all LPUART interrupt configurations.
Values:
-
enumerator kLPUART_LinBreakInterruptEnable
LIN break detect. bit 7
-
enumerator kLPUART_RxActiveEdgeInterruptEnable
Receive Active Edge. bit 6
-
enumerator kLPUART_TxDataRegEmptyInterruptEnable
Transmit data register empty. bit 23
-
enumerator kLPUART_TransmissionCompleteInterruptEnable
Transmission complete. bit 22
-
enumerator kLPUART_RxDataRegFullInterruptEnable
Receiver data register full. bit 21
-
enumerator kLPUART_IdleLineInterruptEnable
Idle line. bit 20
-
enumerator kLPUART_RxOverrunInterruptEnable
Receiver Overrun. bit 27
-
enumerator kLPUART_NoiseErrorInterruptEnable
Noise error flag. bit 26
-
enumerator kLPUART_FramingErrorInterruptEnable
Framing error flag. bit 25
-
enumerator kLPUART_ParityErrorInterruptEnable
Parity error flag. bit 24
-
enumerator kLPUART_Match1InterruptEnable
Parity error flag. bit 15
-
enumerator kLPUART_Match2InterruptEnable
Parity error flag. bit 14
-
enumerator kLPUART_TxFifoOverflowInterruptEnable
Transmit FIFO Overflow. bit 9
-
enumerator kLPUART_RxFifoUnderflowInterruptEnable
Receive FIFO Underflow. bit 8
-
enumerator kLPUART_AllInterruptEnable
-
enumerator kLPUART_LinBreakInterruptEnable
-
enum _lpuart_flags
LPUART status flags.
This provides constants for the LPUART status flags for use in the LPUART functions.
Values:
-
enumerator kLPUART_TxDataRegEmptyFlag
Transmit data register empty flag, sets when transmit buffer is empty. bit 23
-
enumerator kLPUART_TransmissionCompleteFlag
Transmission complete flag, sets when transmission activity complete. bit 22
-
enumerator kLPUART_RxDataRegFullFlag
Receive data register full flag, sets when the receive data buffer is full. bit 21
-
enumerator kLPUART_IdleLineFlag
Idle line detect flag, sets when idle line detected. bit 20
-
enumerator kLPUART_RxOverrunFlag
Receive Overrun, sets when new data is received before data is read from receive register. bit 19
-
enumerator kLPUART_NoiseErrorFlag
Receive takes 3 samples of each received bit. If any of these samples differ, noise flag sets. bit 18
-
enumerator kLPUART_FramingErrorFlag
Frame error flag, sets if logic 0 was detected where stop bit expected. bit 17
-
enumerator kLPUART_ParityErrorFlag
If parity enabled, sets upon parity error detection. bit 16
-
enumerator kLPUART_LinBreakFlag
LIN break detect interrupt flag, sets when LIN break char detected and LIN circuit enabled. bit 31
-
enumerator kLPUART_RxActiveEdgeFlag
Receive pin active edge interrupt flag, sets when active edge detected. bit 30
-
enumerator kLPUART_RxActiveFlag
Receiver Active Flag (RAF), sets at beginning of valid start. bit 24
-
enumerator kLPUART_DataMatch1Flag
The next character to be read from LPUART_DATA matches MA1. bit 15
-
enumerator kLPUART_DataMatch2Flag
The next character to be read from LPUART_DATA matches MA2. bit 14
-
enumerator kLPUART_TxFifoEmptyFlag
TXEMPT bit, sets if transmit buffer is empty. bit 7
-
enumerator kLPUART_RxFifoEmptyFlag
RXEMPT bit, sets if receive buffer is empty. bit 6
-
enumerator kLPUART_TxFifoOverflowFlag
TXOF bit, sets if transmit buffer overflow occurred. bit 1
-
enumerator kLPUART_RxFifoUnderflowFlag
RXUF bit, sets if receive buffer underflow occurred. bit 0
-
enumerator kLPUART_AllClearFlags
-
enumerator kLPUART_AllFlags
-
enumerator kLPUART_TxDataRegEmptyFlag
-
typedef enum _lpuart_parity_mode lpuart_parity_mode_t
LPUART parity mode.
-
typedef enum _lpuart_data_bits lpuart_data_bits_t
LPUART data bits count.
-
typedef enum _lpuart_stop_bit_count lpuart_stop_bit_count_t
LPUART stop bit count.
-
typedef enum _lpuart_transmit_cts_source lpuart_transmit_cts_source_t
LPUART transmit CTS source.
-
typedef enum _lpuart_transmit_cts_config lpuart_transmit_cts_config_t
LPUART transmit CTS configure.
-
typedef enum _lpuart_idle_type_select lpuart_idle_type_select_t
LPUART idle flag type defines when the receiver starts counting.
-
typedef enum _lpuart_idle_config lpuart_idle_config_t
LPUART idle detected configuration. This structure defines the number of idle characters that must be received before the IDLE flag is set.
-
typedef struct _lpuart_config lpuart_config_t
LPUART configuration structure.
-
typedef struct _lpuart_transfer lpuart_transfer_t
LPUART transfer structure.
-
typedef struct _lpuart_handle lpuart_handle_t
-
typedef void (*lpuart_transfer_callback_t)(LPUART_Type *base, lpuart_handle_t *handle, status_t status, void *userData)
LPUART transfer callback function.
-
typedef void (*lpuart_isr_t)(LPUART_Type *base, void *handle)
-
void *s_lpuartHandle[]
-
const IRQn_Type s_lpuartTxIRQ[]
-
lpuart_isr_t s_lpuartIsr[]
-
UART_RETRY_TIMES
Retry times for waiting flag.
-
struct _lpuart_config
- #include <fsl_lpuart.h>
LPUART configuration structure.
Public Members
-
uint32_t baudRate_Bps
LPUART baud rate
-
lpuart_parity_mode_t parityMode
Parity mode, disabled (default), even, odd
-
lpuart_data_bits_t dataBitsCount
Data bits count, eight (default), seven
-
bool isMsb
Data bits order, LSB (default), MSB
-
lpuart_stop_bit_count_t stopBitCount
Number of stop bits, 1 stop bit (default) or 2 stop bits
-
uint8_t txFifoWatermark
TX FIFO watermark
-
uint8_t rxFifoWatermark
RX FIFO watermark
-
bool enableRxRTS
RX RTS enable
-
bool enableTxCTS
TX CTS enable
-
lpuart_transmit_cts_source_t txCtsSource
TX CTS source
-
lpuart_transmit_cts_config_t txCtsConfig
TX CTS configure
-
lpuart_idle_type_select_t rxIdleType
RX IDLE type.
-
lpuart_idle_config_t rxIdleConfig
RX IDLE configuration.
-
bool enableTx
Enable TX
-
bool enableRx
Enable RX
-
uint32_t baudRate_Bps
-
struct _lpuart_transfer
- #include <fsl_lpuart.h>
LPUART transfer structure.
Public Members
-
size_t dataSize
The byte count to be transfer.
-
size_t dataSize
-
struct _lpuart_handle
- #include <fsl_lpuart.h>
LPUART handle structure.
Public Members
-
volatile size_t txDataSize
Size of the remaining data to send.
-
size_t txDataSizeAll
Size of the data to send out.
-
volatile size_t rxDataSize
Size of the remaining data to receive.
-
size_t rxDataSizeAll
Size of the data to receive.
-
size_t rxRingBufferSize
Size of the ring buffer.
-
volatile uint16_t rxRingBufferHead
Index for the driver to store received data into ring buffer.
-
volatile uint16_t rxRingBufferTail
Index for the user to get data from the ring buffer.
-
lpuart_transfer_callback_t callback
Callback function.
-
void *userData
LPUART callback function parameter.
-
volatile uint8_t txState
TX transfer state.
-
volatile uint8_t rxState
RX transfer state.
-
bool isSevenDataBits
Seven data bits flag.
-
bool is16bitData
16bit data bits flag, only used for 9bit or 10bit data
-
volatile size_t txDataSize
-
union __unnamed67__
Public Members
-
uint8_t *data
The buffer of data to be transfer.
-
uint8_t *rxData
The buffer to receive data.
-
uint16_t *rxData16
The buffer to receive data.
-
const uint8_t *txData
The buffer of data to be sent.
-
const uint16_t *txData16
The buffer of data to be sent.
-
uint8_t *data
-
union __unnamed69__
Public Members
-
const uint8_t *volatile txData
Address of remaining data to send.
-
const uint16_t *volatile txData16
Address of remaining data to send.
-
const uint8_t *volatile txData
-
union __unnamed71__
Public Members
-
uint8_t *volatile rxData
Address of remaining data to receive.
-
uint16_t *volatile rxData16
Address of remaining data to receive.
-
uint8_t *volatile rxData
-
union __unnamed73__
Public Members
-
uint8_t *rxRingBuffer
Start address of the receiver ring buffer.
-
uint16_t *rxRingBuffer16
Start address of the receiver ring buffer.
-
uint8_t *rxRingBuffer
LPUART eDMA Driver
-
void LPUART_TransferCreateHandleEDMA(LPUART_Type *base, lpuart_edma_handle_t *handle, lpuart_edma_transfer_callback_t callback, void *userData, edma_handle_t *txEdmaHandle, edma_handle_t *rxEdmaHandle)
Initializes the LPUART handle which is used in transactional functions.
Note
This function disables all LPUART interrupts.
- Parameters:
base – LPUART peripheral base address.
handle – Pointer to lpuart_edma_handle_t structure.
callback – Callback function.
userData – User data.
txEdmaHandle – User requested DMA handle for TX DMA transfer.
rxEdmaHandle – User requested DMA handle for RX DMA transfer.
-
status_t LPUART_SendEDMA(LPUART_Type *base, lpuart_edma_handle_t *handle, lpuart_transfer_t *xfer)
Sends data using eDMA.
This function sends data using eDMA. This is a non-blocking function, which returns right away. When all data is sent, the send callback function is called.
- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
xfer – LPUART eDMA transfer structure. See lpuart_transfer_t.
- Return values:
kStatus_Success – if succeed, others failed.
kStatus_LPUART_TxBusy – Previous transfer on going.
kStatus_InvalidArgument – Invalid argument.
-
status_t LPUART_ReceiveEDMA(LPUART_Type *base, lpuart_edma_handle_t *handle, lpuart_transfer_t *xfer)
Receives data using eDMA.
This function receives data using eDMA. This is non-blocking function, which returns right away. When all data is received, the receive callback function is called.
- Parameters:
base – LPUART peripheral base address.
handle – Pointer to lpuart_edma_handle_t structure.
xfer – LPUART eDMA transfer structure, see lpuart_transfer_t.
- Return values:
kStatus_Success – if succeed, others fail.
kStatus_LPUART_RxBusy – Previous transfer ongoing.
kStatus_InvalidArgument – Invalid argument.
-
void LPUART_TransferAbortSendEDMA(LPUART_Type *base, lpuart_edma_handle_t *handle)
Aborts the sent data using eDMA.
This function aborts the sent data using eDMA.
- Parameters:
base – LPUART peripheral base address.
handle – Pointer to lpuart_edma_handle_t structure.
-
void LPUART_TransferAbortReceiveEDMA(LPUART_Type *base, lpuart_edma_handle_t *handle)
Aborts the received data using eDMA.
This function aborts the received data using eDMA.
- Parameters:
base – LPUART peripheral base address.
handle – Pointer to lpuart_edma_handle_t structure.
-
status_t LPUART_TransferGetSendCountEDMA(LPUART_Type *base, lpuart_edma_handle_t *handle, uint32_t *count)
Gets the number of bytes written to the LPUART TX register.
This function gets the number of bytes written to the LPUART TX register by DMA.
- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
count – Send bytes count.
- Return values:
kStatus_NoTransferInProgress – No send in progress.
kStatus_InvalidArgument – Parameter is invalid.
kStatus_Success – Get successfully through the parameter
count
;
-
status_t LPUART_TransferGetReceiveCountEDMA(LPUART_Type *base, lpuart_edma_handle_t *handle, uint32_t *count)
Gets the number of received bytes.
This function gets the number of received bytes.
- Parameters:
base – LPUART peripheral base address.
handle – LPUART handle pointer.
count – Receive bytes count.
- Return values:
kStatus_NoTransferInProgress – No receive in progress.
kStatus_InvalidArgument – Parameter is invalid.
kStatus_Success – Get successfully through the parameter
count
;
-
void LPUART_TransferEdmaHandleIRQ(LPUART_Type *base, void *lpuartEdmaHandle)
LPUART eDMA IRQ handle function.
This function handles the LPUART tx complete IRQ request and invoke user callback. It is not set to static so that it can be used in user application.
Note
This function is used as default IRQ handler by double weak mechanism. If user’s specific IRQ handler is implemented, make sure this function is invoked in the handler.
- Parameters:
base – LPUART peripheral base address.
lpuartEdmaHandle – LPUART handle pointer.
-
FSL_LPUART_EDMA_DRIVER_VERSION
LPUART EDMA driver version.
-
typedef struct _lpuart_edma_handle lpuart_edma_handle_t
-
typedef void (*lpuart_edma_transfer_callback_t)(LPUART_Type *base, lpuart_edma_handle_t *handle, status_t status, void *userData)
LPUART transfer callback function.
-
struct _lpuart_edma_handle
- #include <fsl_lpuart_edma.h>
LPUART eDMA handle.
Public Members
-
lpuart_edma_transfer_callback_t callback
Callback function.
-
void *userData
LPUART callback function parameter.
-
size_t rxDataSizeAll
Size of the data to receive.
-
size_t txDataSizeAll
Size of the data to send out.
-
edma_handle_t *txEdmaHandle
The eDMA TX channel used.
-
edma_handle_t *rxEdmaHandle
The eDMA RX channel used.
-
uint8_t nbytes
eDMA minor byte transfer count initially configured.
-
volatile uint8_t txState
TX transfer state.
-
volatile uint8_t rxState
RX transfer state
-
lpuart_edma_transfer_callback_t callback
Nic301
-
enum _nic_reg
Values:
-
enumerator kNIC_REG_READ_QOS_LCD
-
enumerator kNIC_REG_READ_QOS_CSI
-
enumerator kNIC_REG_READ_QOS_PXP
-
enumerator kNIC_REG_READ_QOS_DCP
-
enumerator kNIC_REG_READ_QOS_ENET
-
enumerator kNIC_REG_READ_QOS_USBO2
-
enumerator kNIC_REG_READ_QOS_USDHC1
-
enumerator kNIC_REG_READ_QOS_USDHC2
-
enumerator kNIC_REG_READ_QOS_TestPort
-
enumerator kNIC_REG_READ_QOS_CM7
-
enumerator kNIC_REG_READ_QOS_DMA
-
enumerator kNIC_REG_WRITE_QOS_LCD
-
enumerator kNIC_REG_WRITE_QOS_CSI
-
enumerator kNIC_REG_WRITE_QOS_PXP
-
enumerator kNIC_REG_WRITE_QOS_DCP
-
enumerator kNIC_REG_WRITE_QOS_ENET
-
enumerator kNIC_REG_WRITE_QOS_USBO2
-
enumerator kNIC_REG_WRITE_QOS_USDHC1
-
enumerator kNIC_REG_WRITE_QOS_USDHC2
-
enumerator kNIC_REG_WRITE_QOS_TestPort
-
enumerator kNIC_REG_WRITE_QOS_CM7
-
enumerator kNIC_REG_WRITE_QOS_DMA
-
enumerator kNIC_REG_FN_MOD_LCD
-
enumerator kNIC_REG_FN_MOD_CSI
-
enumerator kNIC_REG_FN_MOD_PXP
-
enumerator kNIC_REG_FN_MOD_DCP
-
enumerator kNIC_REG_FN_MOD_ENET
-
enumerator kNIC_REG_FN_MOD_USBO2
-
enumerator kNIC_REG_FN_MOD_USDHC1
-
enumerator kNIC_REG_FN_MOD_USDHC2
-
enumerator kNIC_REG_FN_MOD_TestPort
-
enumerator kNIC_REG_FN_MOD_CM7
-
enumerator kNIC_REG_FN_MOD_DMA
-
enumerator kNIC_REG_FN_MOD2_DCP
-
enumerator kNIC_REG_FN_MOD_AHB_ENET
-
enumerator kNIC_REG_FN_MOD_AHB_TestPort
-
enumerator kNIC_REG_FN_MOD_AHB_DMA
-
enumerator kNIC_REG_WR_TIDEMARK_CM7
-
enumerator kNIC_REG_READ_QOS_LCD
-
enum _nic_fn_mod2
Values:
-
enumerator kNIC_FN_MOD2_ENABLE
-
enumerator kNIC_FN_MOD2_BYPASS
-
enumerator kNIC_FN_MOD2_ENABLE
-
enum _nic_fn_mod_ahb
Values:
-
enumerator kNIC_FN_MOD_AHB_RD_INCR_OVERRIDE
-
enumerator kNIC_FN_MOD_AHB_WR_INCR_OVERRIDE
-
enumerator kNIC_FN_MOD_AHB_LOCK_OVERRIDE
-
enumerator kNIC_FN_MOD_AHB_RD_INCR_OVERRIDE
-
enum _nic_fn_mod
Values:
-
enumerator kNIC_FN_MOD_ReadIssue
-
enumerator kNIC_FN_MOD_WriteIssue
-
enumerator kNIC_FN_MOD_ReadIssue
-
enum _nic_qos
Values:
-
enumerator kNIC_QOS_0
-
enumerator kNIC_QOS_1
-
enumerator kNIC_QOS_2
-
enumerator kNIC_QOS_3
-
enumerator kNIC_QOS_4
-
enumerator kNIC_QOS_5
-
enumerator kNIC_QOS_6
-
enumerator kNIC_QOS_7
-
enumerator kNIC_QOS_8
-
enumerator kNIC_QOS_9
-
enumerator kNIC_QOS_10
-
enumerator kNIC_QOS_11
-
enumerator kNIC_QOS_12
-
enumerator kNIC_QOS_13
-
enumerator kNIC_QOS_14
-
enumerator kNIC_QOS_15
-
enumerator kNIC_QOS_0
-
typedef enum _nic_reg nic_reg_t
-
typedef enum _nic_fn_mod2 nic_fn_mod2_t
-
typedef enum _nic_fn_mod_ahb nic_fn_mod_ahb_t
-
typedef enum _nic_fn_mod nic_fn_mod_t
-
typedef enum _nic_qos nic_qos_t
-
static inline void NIC_SetReadQos(nic_reg_t base, nic_qos_t value)
Set read_qos Value.
- Parameters:
base – Base address of GPV address
value – Target value (0 - 15)
-
static inline nic_qos_t NIC_GetReadQos(nic_reg_t base)
Get read_qos Value.
- Parameters:
base – Base address of GPV address
- Returns:
Current value configured
-
static inline void NIC_SetWriteQos(nic_reg_t base, nic_qos_t value)
Set write_qos Value.
- Parameters:
base – Base address of GPV address
value – Target value (0 - 15)
-
static inline nic_qos_t NIC_GetWriteQos(nic_reg_t base)
Get write_qos Value.
- Parameters:
base – Base address of GPV address
- Returns:
Current value configured
-
static inline void NIC_SetFnModAhb(nic_reg_t base, nic_fn_mod_ahb_t value)
Set fn_mod_ahb Value.
- Parameters:
base – Base address of GPV address
value – Target value
-
static inline nic_fn_mod_ahb_t NIC_GetFnModAhb(nic_reg_t base)
Get fn_mod_ahb Value.
- Parameters:
base – Base address of GPV address
- Returns:
Current value configured
-
static inline void NIC_SetWrTideMark(nic_reg_t base, uint8_t value)
Set wr_tidemark Value.
- Parameters:
base – Base address of GPV address
value – Target value (0 - 7)
-
static inline uint8_t NIC_GetWrTideMark(nic_reg_t base)
Get wr_tidemark Value.
- Parameters:
base – Base address of GPV address
- Returns:
Current value configured
-
static inline void NIC_SetFnMod(nic_reg_t base, nic_fn_mod_t value)
Set fn_mod Value.
- Parameters:
base – Base address of GPV address
value – Target value
-
static inline nic_fn_mod_t NIC_GetFnMod(nic_reg_t base)
Get fn_mod Value.
- Parameters:
base – Base address of GPV address
- Returns:
Current value configured
-
static inline void NIC_SetFnMod2(nic_reg_t base, nic_fn_mod_t value)
Set fn_mod2 Value.
- Parameters:
base – Base address of GPV address
value – Target value
-
static inline nic_fn_mod2_t NIC_GetFnMod2(nic_reg_t base)
Get fn_mod2 Value.
- Parameters:
base – Base address of GPV address
- Returns:
Current value configured
-
FSL_NIC301_DRIVER_VERSION
NIC301 driver version 2.0.1.
-
GPV0_BASE
-
GPV1_BASE
-
GPV4_BASE
-
NIC_FN_MOD2_OFFSET
-
NIC_FN_MOD_AHB_OFFSET
-
NIC_WR_TIDEMARK_OFFSET
-
NIC_READ_QOS_OFFSET
-
NIC_WRITE_QOS_OFFSET
-
NIC_FN_MOD_OFFSET
-
NIC_LCD_BASE
-
NIC_CSI_BASE
-
NIC_PXP_BASE
-
NIC_DCP_BASE
-
NIC_ENET_BASE
-
NIC_USBO2_BASE
-
NIC_USDHC1_BASE
-
NIC_USDHC2_BASE
-
NIC_TestPort_BASE
-
NIC_CM7_BASE
-
NIC_DMA_BASE
-
NIC_QOS_MASK
-
NIC_WR_TIDEMARK_MASK
-
NIC_FN_MOD_AHB_MASK
-
NIC_FN_MOD_MASK
-
NIC_FN_MOD2_MASK
-
FSL_COMPONENT_ID
OCOTP: On Chip One-Time Programmable controller.
-
FSL_OCOTP_DRIVER_VERSION
OCOTP driver version.
_ocotp_status Error codes for the OCOTP driver.
Values:
-
enumerator kStatus_OCOTP_AccessError
eFuse and shadow register access error.
-
enumerator kStatus_OCOTP_CrcFail
CRC check failed.
-
enumerator kStatus_OCOTP_ReloadError
Error happens during reload shadow register.
-
enumerator kStatus_OCOTP_ProgramFail
Fuse programming failed.
-
enumerator kStatus_OCOTP_Locked
Fuse is locked and cannot be programmed.
-
enumerator kStatus_OCOTP_AccessError
-
typedef struct _ocotp_timing ocotp_timing_t
OCOTP timing structure. Note that, these value are used for calcalating the read/write timings. And the values should statisfy below rules:
Tsp_rd=(WAIT+1)/ipg_clk_freq should be >= 150ns; Tsp_pgm=(RELAX+1)/ipg_clk_freq should be >= 100ns; Trd = ((STROBE_READ+1)- 2*(RELAX_READ+1)) /ipg_clk_freq, The Trd is required to be larger than 40 ns. Tpgm = ((STROBE_PROG+1)- 2*(RELAX_PROG+1)) /ipg_clk_freq; The Tpgm should be configured within the range of 9000 ns < Tpgm < 11000 ns;
-
void OCOTP_Init(OCOTP_Type *base, uint32_t srcClock_Hz)
Initializes OCOTP controller.
- Parameters:
base – OCOTP peripheral base address.
srcClock_Hz – source clock frequency in unit of Hz. When the macro FSL_FEATURE_OCOTP_HAS_TIMING_CTRL is defined as 0, this parameter is not used, application could pass in 0 in this case.
-
void OCOTP_Deinit(OCOTP_Type *base)
De-initializes OCOTP controller.
- Return values:
kStatus_Success – upon successful execution, error status otherwise.
-
static inline bool OCOTP_CheckBusyStatus(OCOTP_Type *base)
Checking the BUSY bit in CTRL register. Checking this BUSY bit will help confirm if the OCOTP controller is ready for access.
- Parameters:
base – OCOTP peripheral base address.
- Return values:
true – for bit set and false for cleared.
-
static inline bool OCOTP_CheckErrorStatus(OCOTP_Type *base)
Checking the ERROR bit in CTRL register.
- Parameters:
base – OCOTP peripheral base address.
- Return values:
true – for bit set and false for cleared.
-
static inline void OCOTP_ClearErrorStatus(OCOTP_Type *base)
Clear the error bit if this bit is set.
- Parameters:
base – OCOTP peripheral base address.
-
status_t OCOTP_ReloadShadowRegister(OCOTP_Type *base)
Reload the shadow register. This function will help reload the shadow register without reseting the OCOTP module. Please make sure the OCOTP has been initialized before calling this API.
- Parameters:
base – OCOTP peripheral base addess.
- Return values:
kStatus_Success – Reload success.
kStatus_OCOTP_ReloadError – Reload failed.
-
uint32_t OCOTP_ReadFuseShadowRegister(OCOTP_Type *base, uint32_t address)
Read the fuse shadow register with the fuse addess.
- Deprecated:
Use OCOTP_ReadFuseShadowRegisterExt instead of this function.
- Parameters:
base – OCOTP peripheral base address.
address – the fuse address to be read from.
- Returns:
The read out data.
-
status_t OCOTP_ReadFuseShadowRegisterExt(OCOTP_Type *base, uint32_t address, uint32_t *data, uint8_t fuseWords)
Read the fuse shadow register from the fuse addess.
This function reads fuse from
address
, how many words to read is specified by the parameterfuseWords
. This function could read at most OCOTP_READ_FUSE_DATA_COUNT fuse word one time.- Parameters:
base – OCOTP peripheral base address.
address – the fuse address to be read from.
data – Data array to save the readout fuse value.
fuseWords – How many words to read.
- Return values:
kStatus_Success – Read success.
kStatus_Fail – Error occurs during read.
-
status_t OCOTP_WriteFuseShadowRegister(OCOTP_Type *base, uint32_t address, uint32_t data)
Write the fuse shadow register with the fuse addess and data. Please make sure the wrtie address is not locked while calling this API.
- Parameters:
base – OCOTP peripheral base address.
address – the fuse address to be written.
data – the value will be writen to fuse address.
- Return values:
write – status, kStatus_Success for success and kStatus_Fail for failed.
-
status_t OCOTP_WriteFuseShadowRegisterWithLock(OCOTP_Type *base, uint32_t address, uint32_t data, bool lock)
Write the fuse shadow register and lock it.
Please make sure the wrtie address is not locked while calling this API.
Some OCOTP controller supports ECC mode and redundancy mode (see reference mananual for more details). OCOTP controller will auto select ECC or redundancy mode to program the fuse word according to fuse map definition. In ECC mode, the 32 fuse bits in one word can only be written once. In redundancy mode, the word can be written more than once as long as they are different fuse bits. Set parameter
lock
as true to force use ECC mode.- Parameters:
base – OCOTP peripheral base address.
address – The fuse address to be written.
data – The value will be writen to fuse address.
lock – Lock or unlock write fuse shadow register operation.
- Return values:
kStatus_Success – Program and reload success.
kStatus_OCOTP_Locked – The eFuse word is locked and cannot be programmed.
kStatus_OCOTP_ProgramFail – eFuse word programming failed.
kStatus_OCOTP_ReloadError – eFuse word programming success, but error happens during reload the values.
kStatus_OCOTP_AccessError – Cannot access eFuse word.
-
static inline uint32_t OCOTP_GetVersion(OCOTP_Type *base)
Get the OCOTP controller version from the register.
- Parameters:
base – OCOTP peripheral base address.
- Return values:
return – the version value.
-
OCOTP_READ_FUSE_DATA_COUNT
-
struct _ocotp_timing
- #include <fsl_ocotp.h>
OCOTP timing structure. Note that, these value are used for calcalating the read/write timings. And the values should statisfy below rules:
Tsp_rd=(WAIT+1)/ipg_clk_freq should be >= 150ns; Tsp_pgm=(RELAX+1)/ipg_clk_freq should be >= 100ns; Trd = ((STROBE_READ+1)- 2*(RELAX_READ+1)) /ipg_clk_freq, The Trd is required to be larger than 40 ns. Tpgm = ((STROBE_PROG+1)- 2*(RELAX_PROG+1)) /ipg_clk_freq; The Tpgm should be configured within the range of 9000 ns < Tpgm < 11000 ns;
Public Members
-
uint32_t wait
Wait time value to fill in the TIMING register.
-
uint32_t relax
Relax time value to fill in the TIMING register.
-
uint32_t strobe_prog
Storbe program time value to fill in the TIMING register.
-
uint32_t strobe_read
Storbe read time value to fill in the TIMING register.
-
uint32_t wait
PIT: Periodic Interrupt Timer
-
void PIT_Init(PIT_Type *base, const pit_config_t *config)
Ungates the PIT clock, enables the PIT module, and configures the peripheral for basic operations.
Note
This API should be called at the beginning of the application using the PIT driver.
- Parameters:
base – PIT peripheral base address
config – Pointer to the user’s PIT config structure
-
void PIT_Deinit(PIT_Type *base)
Gates the PIT clock and disables the PIT module.
- Parameters:
base – PIT peripheral base address
-
static inline void PIT_GetDefaultConfig(pit_config_t *config)
Fills in the PIT configuration structure with the default settings.
The default values are as follows.
config->enableRunInDebug = false;
- Parameters:
config – Pointer to the configuration structure.
-
static inline void PIT_SetTimerChainMode(PIT_Type *base, pit_chnl_t channel, bool enable)
Enables or disables chaining a timer with the previous timer.
When a timer has a chain mode enabled, it only counts after the previous timer has expired. If the timer n-1 has counted down to 0, counter n decrements the value by one. Each timer is 32-bits, which allows the developers to chain timers together and form a longer timer (64-bits and larger). The first timer (timer 0) can’t be chained to any other timer.
- Parameters:
base – PIT peripheral base address
channel – Timer channel number which is chained with the previous timer
enable – Enable or disable chain. true: Current timer is chained with the previous timer. false: Timer doesn’t chain with other timers.
-
static inline void PIT_EnableInterrupts(PIT_Type *base, pit_chnl_t channel, uint32_t mask)
Enables the selected PIT interrupts.
- Parameters:
base – PIT peripheral base address
channel – Timer channel number
mask – The interrupts to enable. This is a logical OR of members of the enumeration pit_interrupt_enable_t
-
static inline void PIT_DisableInterrupts(PIT_Type *base, pit_chnl_t channel, uint32_t mask)
Disables the selected PIT interrupts.
- Parameters:
base – PIT peripheral base address
channel – Timer channel number
mask – The interrupts to disable. This is a logical OR of members of the enumeration pit_interrupt_enable_t
-
static inline uint32_t PIT_GetEnabledInterrupts(PIT_Type *base, pit_chnl_t channel)
Gets the enabled PIT interrupts.
- Parameters:
base – PIT peripheral base address
channel – Timer channel number
- Returns:
The enabled interrupts. This is the logical OR of members of the enumeration pit_interrupt_enable_t
-
static inline uint32_t PIT_GetStatusFlags(PIT_Type *base, pit_chnl_t channel)
Gets the PIT status flags.
- Parameters:
base – PIT peripheral base address
channel – Timer channel number
- Returns:
The status flags. This is the logical OR of members of the enumeration pit_status_flags_t
-
static inline void PIT_ClearStatusFlags(PIT_Type *base, pit_chnl_t channel, uint32_t mask)
Clears the PIT status flags.
- Parameters:
base – PIT peripheral base address
channel – Timer channel number
mask – The status flags to clear. This is a logical OR of members of the enumeration pit_status_flags_t
-
static inline void PIT_SetTimerPeriod(PIT_Type *base, pit_chnl_t channel, uint32_t count)
Sets the timer period in units of count.
Timers begin counting from the value set by this function until it reaches 0, then it generates an interrupt and load this register value again. Writing a new value to this register does not restart the timer. Instead, the value is loaded after the timer expires.
Note
Users can call the utility macros provided in fsl_common.h to convert to ticks.
- Parameters:
base – PIT peripheral base address
channel – Timer channel number
count – Timer period in units of ticks
-
static inline uint32_t PIT_GetCurrentTimerCount(PIT_Type *base, pit_chnl_t channel)
Reads the current timer counting value.
This function returns the real-time timer counting value, in a range from 0 to a timer period.
Note
Users can call the utility macros provided in fsl_common.h to convert ticks to usec or msec.
- Parameters:
base – PIT peripheral base address
channel – Timer channel number
- Returns:
Current timer counting value in ticks
-
static inline void PIT_StartTimer(PIT_Type *base, pit_chnl_t channel)
Starts the timer counting.
After calling this function, timers load period value, count down to 0 and then load the respective start value again. Each time a timer reaches 0, it generates a trigger pulse and sets the timeout interrupt flag.
- Parameters:
base – PIT peripheral base address
channel – Timer channel number.
-
static inline void PIT_StopTimer(PIT_Type *base, pit_chnl_t channel)
Stops the timer counting.
This function stops every timer counting. Timers reload their periods respectively after the next time they call the PIT_DRV_StartTimer.
- Parameters:
base – PIT peripheral base address
channel – Timer channel number.
-
FSL_PIT_DRIVER_VERSION
PIT Driver Version 2.0.5.
-
enum _pit_chnl
List of PIT channels.
Note
Actual number of available channels is SoC dependent
Values:
-
enumerator kPIT_Chnl_0
PIT channel number 0
-
enumerator kPIT_Chnl_1
PIT channel number 1
-
enumerator kPIT_Chnl_2
PIT channel number 2
-
enumerator kPIT_Chnl_3
PIT channel number 3
-
enumerator kPIT_Chnl_0
-
enum _pit_interrupt_enable
List of PIT interrupts.
Values:
-
enumerator kPIT_TimerInterruptEnable
Timer interrupt enable
-
enumerator kPIT_TimerInterruptEnable
-
enum _pit_status_flags
List of PIT status flags.
Values:
-
enumerator kPIT_TimerFlag
Timer flag
-
enumerator kPIT_TimerFlag
-
typedef enum _pit_chnl pit_chnl_t
List of PIT channels.
Note
Actual number of available channels is SoC dependent
-
typedef enum _pit_interrupt_enable pit_interrupt_enable_t
List of PIT interrupts.
-
typedef enum _pit_status_flags pit_status_flags_t
List of PIT status flags.
-
typedef struct _pit_config pit_config_t
PIT configuration structure.
This structure holds the configuration settings for the PIT peripheral. To initialize this structure to reasonable defaults, call the PIT_GetDefaultConfig() function and pass a pointer to your config structure instance.
The configuration structure can be made constant so it resides in flash.
-
uint64_t PIT_GetLifetimeTimerCount(PIT_Type *base)
Reads the current lifetime counter value.
The lifetime timer is a 64-bit timer which chains timer 0 and timer 1 together. Timer 0 and 1 are chained by calling the PIT_SetTimerChainMode before using this timer. The period of lifetime timer is equal to the “period of timer 0 * period of timer 1”. For the 64-bit value, the higher 32-bit has the value of timer 1, and the lower 32-bit has the value of timer 0.
- Parameters:
base – PIT peripheral base address
- Returns:
Current lifetime timer value
-
struct _pit_config
- #include <fsl_pit.h>
PIT configuration structure.
This structure holds the configuration settings for the PIT peripheral. To initialize this structure to reasonable defaults, call the PIT_GetDefaultConfig() function and pass a pointer to your config structure instance.
The configuration structure can be made constant so it resides in flash.
Public Members
-
bool enableRunInDebug
true: Timers run in debug mode; false: Timers stop in debug mode
-
bool enableRunInDebug
PMU: Power Management Unit
-
uint32_t PMU_GetStatusFlags(PMU_Type *base)
Get PMU status flags.
- Parameters:
base – PMU peripheral base address.
- Returns:
PMU status flags.It indicate if regulator output of 1P1,3P0 and 2P5 is ok and brownout output of 1P1,3P0 and 2P5 is detected.
-
static inline void PMU_1P1SetWeakReferenceSource(PMU_Type *base, pmu_1p1_weak_reference_source_t option)
Selects the source for the reference voltage of the weak 1P1 regulator.
- Parameters:
base – PMU peripheral base address.
option – The option for reference voltage source, see to pmu_1p1_weak_reference_source_t.
-
static inline void PMU_1P1EnableWeakRegulator(PMU_Type *base, bool enable)
Enables the weak 1P1 regulator.
This regulator can be used when the main 1P1 regulator is disabled, under low-power conditions.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_1P1SetRegulatorOutputVoltage(PMU_Type *base, uint32_t value)
Adjust the 1P1 regulator output voltage.
Each LSB is worth 25mV. Programming examples are detailed below. Other output target voltages may be interpolated from these examples. Choices must be in this range:
0x1b(1.375V) >= output_trg >= 0x04(0.8V)
0x04 : 0.8V
0x10 : 1.1V (typical)
0x1b : 1.375V NOTE: There may be reduced chip functionality or reliability at the extremes of the programming range.
- Parameters:
base – PMU peripheral base address.
value – Setting value for the output.
-
static inline void PMU_1P1SetBrownoutOffsetVoltage(PMU_Type *base, uint32_t value)
Adjust the 1P1 regulator brownout offset voltage.
Control bits to adjust the regulator brownout offset voltage in 25mV steps. The reset brown-offset is 175mV below the programmed target code. Brownout target = OUTPUT_TRG - BO_OFFSET. Some steps may be irrelevant because of input supply limitations or load operation.
- Parameters:
base – PMU peripheral base address.
value – Setting value for the brownout offset. The available range is in 3-bit.
-
static inline void PMU_1P1EnablePullDown(PMU_Type *base, bool enable)
Enable the pull-down circuitry in the regulator.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_1P1EnableCurrentLimit(PMU_Type *base, bool enable)
Enable the current-limit circuitry in the regulator.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_1P1EnableBrownout(PMU_Type *base, bool enable)
Enable the brownout circuitry in the regulator.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_1P1EnableOutput(PMU_Type *base, bool enable)
Enable the regulator output.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_3P0SetRegulatorOutputVoltage(PMU_Type *base, uint32_t value)
Adjust the 3P0 regulator output voltage.
Each LSB is worth 25mV. Programming examples are detailed below. Other output target voltages may be interpolated from these examples. Choices must be in this range:
0x00(2.625V) >= output_trg >= 0x1f(3.4V)
0x00 : 2.625V
0x0f : 3.0V (typical)
0x1f : 3.4V
- Parameters:
base – PMU peripheral base address.
value – Setting value for the output.
-
static inline void PMU_3P0SetVBusVoltageSource(PMU_Type *base, pmu_3p0_vbus_voltage_source_t option)
Select input voltage source for LDO_3P0.
Select input voltage source for LDO_3P0 from either USB_OTG1_VBUS or USB_OTG2_VBUS. If only one of the two VBUS voltages is present, it is automatically selected.
- Parameters:
base – PMU peripheral base address.
option – User-defined input voltage source for LDO_3P0.
-
static inline void PMU_3P0SetBrownoutOffsetVoltage(PMU_Type *base, uint32_t value)
Adjust the 3P0 regulator brownout offset voltage.
Control bits to adjust the 3P0 regulator brownout offset voltage in 25mV steps. The reset brown-offset is 175mV below the programmed target code. Brownout target = OUTPUT_TRG - BO_OFFSET. Some steps may be irrelevant because of input supply limitations or load operation.
- Parameters:
base – PMU peripheral base address.
value – Setting value for the brownout offset. The available range is in 3-bit.
-
static inline void PMU_3P0EnableCurrentLimit(PMU_Type *base, bool enable)
Enable the current-limit circuitry in the 3P0 regulator.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_3P0EnableBrownout(PMU_Type *base, bool enable)
Enable the brownout circuitry in the 3P0 regulator.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_3P0EnableOutput(PMU_Type *base, bool enable)
Enable the 3P0 regulator output.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_2P5EnableWeakRegulator(PMU_Type *base, bool enable)
Enables the weak 2P5 regulator.
This low power regulator is used when the main 2P5 regulator is disabled to keep the 2.5V output roughly at 2.5V. Scales directly with the value of VDDHIGH_IN.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_2P5SetRegulatorOutputVoltage(PMU_Type *base, uint32_t value)
Adjust the 1P1 regulator output voltage.
Each LSB is worth 25mV. Programming examples are detailed below. Other output target voltages may be interpolated from these examples. Choices must be in this range:
0x00(2.1V) >= output_trg >= 0x1f(2.875V)
0x00 : 2.1V
0x10 : 2.5V (typical)
0x1f : 2.875V NOTE: There may be reduced chip functionality or reliability at the extremes of the programming range.
- Parameters:
base – PMU peripheral base address.
value – Setting value for the output.
-
static inline void PMU_2P5SetBrownoutOffsetVoltage(PMU_Type *base, uint32_t value)
Adjust the 2P5 regulator brownout offset voltage.
Adjust the regulator brownout offset voltage in 25mV steps. The reset brown-offset is 175mV below the programmed target code. Brownout target = OUTPUT_TRG - BO_OFFSET. Some steps may be irrelevant because of input supply limitations or load operation.
- Parameters:
base – PMU peripheral base address.
value – Setting value for the brownout offset. The available range is in 3-bit.
-
static inline void PMU_2P5EnablePullDown(PMU_Type *base, bool enable)
Enable the pull-down circuitry in the 2P5 regulator.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_2P1EnablePullDown(PMU_Type *base, bool enable)
Enable the pull-down circuitry in the 2P5 regulator.
- Deprecated:
Do not use this function. It has been superceded by PMU_2P5EnablePullDown.
-
static inline void PMU_2P5EnableCurrentLimit(PMU_Type *base, bool enable)
Enable the current-limit circuitry in the 2P5 regulator.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_2P5nableBrownout(PMU_Type *base, bool enable)
Enable the brownout circuitry in the 2P5 regulator.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_2P5EnableOutput(PMU_Type *base, bool enable)
Enable the 2P5 regulator output.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_CoreEnableIncreaseGateDrive(PMU_Type *base, bool enable)
Increase the gate drive on power gating FETs.
If set, increases the gate drive on power gating FETs to reduce leakage in the off state. Care must be taken to apply this bit only when the input supply voltage to the power FET is less than 1.1V. NOTE: This bit should only be used in low-power modes where the external input supply voltage is nominally 0.9V.
- Parameters:
base – PMU peripheral base address.
enable – Enable the feature or not.
-
static inline void PMU_CoreSetRegulatorVoltageRampRate(PMU_Type *base, pmu_core_reg_voltage_ramp_rate_t option)
Set the CORE regulator voltage ramp rate.
- Parameters:
base – PMU peripheral base address.
option – User-defined option for voltage ramp rate, see to pmu_core_reg_voltage_ramp_rate_t.
-
static inline void PMU_CoreSetSOCDomainVoltage(PMU_Type *base, uint32_t value)
Define the target voltage for the SOC power domain.
Define the target voltage for the SOC power domain. Single-bit increments reflect 25mV core voltage steps. Some steps may not be relevant because of input supply limitations or load operation.
0x00 : Power gated off.
0x01 : Target core voltage = 0.725V
0x02 : Target core voltage = 0.750V
…
0x10 : Target core voltage = 1.100V
…
0x1e : Target core voltage = 1.450V
0x1F : Power FET switched full on. No regulation. NOTE: This register is capable of programming an over-voltage condition on the device. Consult the datasheet Operating Ranges table for the allowed voltages.
- Parameters:
base – PMU peripheral base address.
value – Setting value for target voltage. 5-bit available
-
static inline void PMU_CoreSetARMCoreDomainVoltage(PMU_Type *base, uint32_t value)
Define the target voltage for the ARM Core power domain.
Define the target voltage for the ARM Core power domain. Single-bit increments reflect 25mV core voltage steps. Some steps may not be relevant because of input supply limitations or load operation.
0x00 : Power gated off.
0x01 : Target core voltage = 0.725V
0x02 : Target core voltage = 0.750V
…
0x10 : Target core voltage = 1.100V
…
0x1e : Target core voltage = 1.450V
0x1F : Power FET switched full on. No regulation. NOTE: This register is capable of programming an over-voltage condition on the device. Consult the datasheet Operating Ranges table for the allowed voltages.
- Parameters:
base – PMU peripheral base address.
value – Setting value for target voltage. 5-bit available
-
static inline void PMU_GatePower(PMU_Type *base, uint32_t gates)
Gate the power to modules.
- Parameters:
base – PMU peripheral base address.
gates – Mask value for the module to be gated. See to _pmu_power_gate.
-
static inline void PMU_UngatePower(PMU_Type *base, uint32_t gates)
Ungate the power to modules.
- Parameters:
base – PMU peripheral base address.
gates – Mask value for the module to be gated. See to _pmu_power_gate.
-
static inline void PMU_EnableLowPowerBandgap(PMU_Type *base, bool enable)
Enable the low power bandgap.
- Parameters:
base – PMU peripheral base address.
enable – Enable the low power bandgap or use the normal power bandgap. @
-
FSL_PMU_DRIVER_VERSION
PMU driver version.
Version 2.1.1.
PMU Status flags.
Values:
-
enumerator kPMU_1P1RegulatorOutputOK
Status bit that signals when the 1p1 regulator output is ok. 1 = regulator output > brownout target.
-
enumerator kPMU_1P1BrownoutOnOutput
Status bit that signals when a 1p1 brownout is detected on the regulator output.
-
enumerator kPMU_3P0RegulatorOutputOK
Status bit that signals when the 3p0 regulator output is ok. 1 = regulator output > brownout target.
-
enumerator kPMU_3P0BrownoutOnOutput
Status bit that signals when a 3p0 brownout is detected on the regulator output.
-
enumerator kPMU_2P5RegulatorOutputOK
Status bit that signals when the 2p5 regulator output is ok. 1 = regulator output > brownout target.
-
enumerator kPMU_2P5BrownoutOnOutput
Status bit that signals when a 2p5 brownout is detected on the regulator output.
-
enumerator kPMU_1P1RegulatorOutputOK
-
enum _pmu_1p1_weak_reference_source
The source for the reference voltage of the weak 1P1 regulator.
Values:
-
enumerator kPMU_1P1WeakReferenceSourceAlt0
Weak-linreg output tracks low-power-bandgap voltage.
-
enumerator kPMU_1P1WeakReferenceSourceAlt1
Weak-linreg output tracks VDD_SOC_CAP voltage.
-
enumerator kPMU_1P1WeakReferenceSourceAlt0
-
enum _pmu_3p0_vbus_voltage_source
Input voltage source for LDO_3P0 from USB VBus.
Values:
-
enumerator kPMU_3P0VBusVoltageSourceAlt0
USB_OTG1_VBUS - Utilize VBUS OTG1 for power.
-
enumerator kPMU_3P0VBusVoltageSourceAlt1
USB_OTG2_VBUS - Utilize VBUS OTG2 for power.
-
enumerator kPMU_3P0VBusVoltageSourceAlt0
-
enum _pmu_core_reg_voltage_ramp_rate
Regulator voltage ramp rate.
Values:
-
enumerator kPMU_CoreRegVoltageRampRateFast
Fast.
-
enumerator kPMU_CoreRegVoltageRampRateMediumFast
Medium Fast.
-
enumerator kPMU_CoreRegVoltageRampRateMediumSlow
Medium Slow.
-
enumerator kPMU_CoreRegVoltageRampRateSlow
Slow.
-
enumerator kPMU_CoreRegVoltageRampRateFast
-
enum _pmu_power_gate
Mask values of power gate.
Values:
-
enumerator kPMU_PowerGateDisplay
Display power gate control.
-
enumerator kPMU_PowerGateDisplayLogic
Display logic power gate control.
-
enumerator kPMU_PowerGateL2
L2 power gate control.
-
enumerator kPMU_PowerGateL1
L1 power gate control.
-
enumerator kPMU_PowerGateRefTopIBias
Low power reftop ibias disable.
-
enumerator kPMU_PowerGateDisplay
-
enum _pmu_power_bandgap
Bandgap select.
Values:
-
enumerator kPMU_NormalPowerBandgap
Normal power bandgap.
-
enumerator kPMU_LowPowerBandgap
Low power bandgap.
-
enumerator kPMU_NormalPowerBandgap
-
typedef enum _pmu_1p1_weak_reference_source pmu_1p1_weak_reference_source_t
The source for the reference voltage of the weak 1P1 regulator.
-
typedef enum _pmu_3p0_vbus_voltage_source pmu_3p0_vbus_voltage_source_t
Input voltage source for LDO_3P0 from USB VBus.
-
typedef enum _pmu_core_reg_voltage_ramp_rate pmu_core_reg_voltage_ramp_rate_t
Regulator voltage ramp rate.
-
typedef enum _pmu_power_bandgap pmu_power_bandgap_t
Bandgap select.
PWM: Pulse Width Modulator
-
status_t PWM_Init(PWM_Type *base, pwm_submodule_t subModule, const pwm_config_t *config)
Ungates the PWM submodule clock and configures the peripheral for basic operation.
This API should be called at the beginning of the application using the PWM driver. When user select PWMX, user must choose edge aligned output, becasue there are some limitation on center aligned PWMX output. When output PWMX in center aligned mode, VAL1 register controls both PWM period and PWMX duty cycle, PWMA and PWMB output will be corrupted. But edge aligned PWMX output do not have such limit. In master reload counter initialization mode, PWM period is depended by period of set LDOK in submodule 0 because this operation will reload register. Submodule 0 counter initialization cannot be master sync or master reload.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
config – Pointer to user’s PWM config structure.
- Returns:
kStatus_Success means success; else failed.
-
void PWM_Deinit(PWM_Type *base, pwm_submodule_t subModule)
Gate the PWM submodule clock.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to deinitialize
-
void PWM_GetDefaultConfig(pwm_config_t *config)
Fill in the PWM config struct with the default settings.
The default values are:
config->enableDebugMode = false; config->enableWait = false; config->reloadSelect = kPWM_LocalReload; config->clockSource = kPWM_BusClock; config->prescale = kPWM_Prescale_Divide_1; config->initializationControl = kPWM_Initialize_LocalSync; config->forceTrigger = kPWM_Force_Local; config->reloadFrequency = kPWM_LoadEveryOportunity; config->reloadLogic = kPWM_ReloadImmediate; config->pairOperation = kPWM_Independent;
- Parameters:
config – Pointer to user’s PWM config structure.
-
status_t PWM_SetupPwm(PWM_Type *base, pwm_submodule_t subModule, const pwm_signal_param_t *chnlParams, uint8_t numOfChnls, pwm_mode_t mode, uint32_t pwmFreq_Hz, uint32_t srcClock_Hz)
Sets up the PWM signals for a PWM submodule.
The function initializes the submodule according to the parameters passed in by the user. The function also sets up the value compare registers to match the PWM signal requirements. If the dead time insertion logic is enabled, the pulse period is reduced by the dead time period specified by the user. When user select PWMX, user must choose edge aligned output, becasue there are some limitation on center aligned PWMX output. Due to edge aligned PWMX is negative true signal, need to configure PWMX active low true level to get correct duty cycle. The half cycle point will not be exactly in the middle of the PWM cycle when PWMX enabled.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
chnlParams – Array of PWM channel parameters to configure the channel(s).
numOfChnls – Number of channels to configure, this should be the size of the array passed in. Array size should not be more than 3 as each submodule has 3 pins to output PWM.
mode – PWM operation mode, options available in enumeration pwm_mode_t
pwmFreq_Hz – PWM signal frequency in Hz
srcClock_Hz – PWM source clock of correspond submodule in Hz. If source clock of submodule1,2,3 is from submodule0 AUX_CLK, its source clock is submodule0 source clock divided with submodule0 prescaler value instead of submodule0 source clock.
- Returns:
Returns kStatus_Fail if there was error setting up the signal; kStatus_Success otherwise
-
status_t PWM_SetupPwmPhaseShift(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel, uint32_t pwmFreq_Hz, uint32_t srcClock_Hz, uint8_t shiftvalue, bool doSync)
Set PWM phase shift for PWM channel running on channel PWM_A, PWM_B which with 50% duty cycle.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmChannel – PWM channel to configure
pwmFreq_Hz – PWM signal frequency in Hz
srcClock_Hz – PWM main counter clock in Hz.
shiftvalue – Phase shift value, range in 0 ~ 50
doSync – true: Set LDOK bit for the submodule list; false: LDOK bit don’t set, need to call PWM_SetPwmLdok to sync update.
- Returns:
Returns kStatus_Fail if there was error setting up the signal; kStatus_Success otherwise
-
void PWM_UpdatePwmDutycycle(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmSignal, pwm_mode_t currPwmMode, uint8_t dutyCyclePercent)
Updates the PWM signal’s dutycycle.
The function updates the PWM dutycyle to the new value that is passed in. If the dead time insertion logic is enabled then the pulse period is reduced by the dead time period specified by the user.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmSignal – Signal (PWM A, PWM B, PWM X) to update
currPwmMode – The current PWM mode set during PWM setup
dutyCyclePercent – New PWM pulse width, value should be between 0 to 100 0=inactive signal(0% duty cycle)… 100=active signal (100% duty cycle)
-
void PWM_UpdatePwmDutycycleHighAccuracy(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmSignal, pwm_mode_t currPwmMode, uint16_t dutyCycle)
Updates the PWM signal’s dutycycle with 16-bit accuracy.
The function updates the PWM dutycyle to the new value that is passed in. If the dead time insertion logic is enabled then the pulse period is reduced by the dead time period specified by the user.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmSignal – Signal (PWM A, PWM B, PWM X) to update
currPwmMode – The current PWM mode set during PWM setup
dutyCycle – New PWM pulse width, value should be between 0 to 65535 0=inactive signal(0% duty cycle)… 65535=active signal (100% duty cycle)
-
void PWM_UpdatePwmPeriodAndDutycycle(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmSignal, pwm_mode_t currPwmMode, uint16_t pulseCnt, uint16_t dutyCycle)
Update the PWM signal’s period and dutycycle for a PWM submodule.
The function updates PWM signal period generated by a specific submodule according to the parameters passed in by the user. This function can also set dutycycle weather you want to keep original dutycycle or update new dutycycle. Call this function in local sync control mode because PWM period is depended by
INIT and VAL1 register of each submodule. In master sync initialization control mode, call this function to update INIT and VAL1 register of all submodule because PWM period is depended by INIT and VAL1 register in submodule0. If the dead time insertion logic is enabled, the pulse period is reduced by the dead time period specified by the user. PWM signal will not be generated if its period is less than dead time duration.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmSignal – Signal (PWM A or PWM B) to update
currPwmMode – The current PWM mode set during PWM setup, options available in enumeration pwm_mode_t
pulseCnt – New PWM period, value should be between 0 to 65535 0=minimum PWM period… 65535=maximum PWM period
dutyCycle – New PWM pulse width of channel, value should be between 0 to 65535 0=inactive signal(0% duty cycle)… 65535=active signal (100% duty cycle) You can keep original duty cycle or update new duty cycle
-
static inline void PWM_EnableInterrupts(PWM_Type *base, pwm_submodule_t subModule, uint32_t mask)
Enables the selected PWM interrupts.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
mask – The interrupts to enable. This is a logical OR of members of the enumeration pwm_interrupt_enable_t
-
static inline void PWM_DisableInterrupts(PWM_Type *base, pwm_submodule_t subModule, uint32_t mask)
Disables the selected PWM interrupts.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
mask – The interrupts to enable. This is a logical OR of members of the enumeration pwm_interrupt_enable_t
-
static inline uint32_t PWM_GetEnabledInterrupts(PWM_Type *base, pwm_submodule_t subModule)
Gets the enabled PWM interrupts.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
- Returns:
The enabled interrupts. This is the logical OR of members of the enumeration pwm_interrupt_enable_t
-
static inline void PWM_DMAFIFOWatermarkControl(PWM_Type *base, pwm_submodule_t subModule, pwm_watermark_control_t pwm_watermark_control)
Capture DMA Enable Source Select.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwm_watermark_control – PWM FIFO watermark and control
-
static inline void PWM_DMACaptureSourceSelect(PWM_Type *base, pwm_submodule_t subModule, pwm_dma_source_select_t pwm_dma_source_select)
Capture DMA Enable Source Select.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwm_dma_source_select – PWM capture DMA enable source select
-
static inline void PWM_EnableDMACapture(PWM_Type *base, pwm_submodule_t subModule, uint16_t mask, bool activate)
Enables or disables the selected PWM DMA Capture read request.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
mask – The DMA to enable or disable. This is a logical OR of members of the enumeration pwm_dma_enable_t
activate – true: Enable DMA read request; false: Disable DMA read request
-
static inline void PWM_EnableDMAWrite(PWM_Type *base, pwm_submodule_t subModule, bool activate)
Enables or disables the PWM DMA write request.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
activate – true: Enable DMA write request; false: Disable DMA write request
-
static inline uint32_t PWM_GetStatusFlags(PWM_Type *base, pwm_submodule_t subModule)
Gets the PWM status flags.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
- Returns:
The status flags. This is the logical OR of members of the enumeration pwm_status_flags_t
-
static inline void PWM_ClearStatusFlags(PWM_Type *base, pwm_submodule_t subModule, uint32_t mask)
Clears the PWM status flags.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
mask – The status flags to clear. This is a logical OR of members of the enumeration pwm_status_flags_t
-
static inline void PWM_StartTimer(PWM_Type *base, uint8_t subModulesToStart)
Starts the PWM counter for a single or multiple submodules.
Sets the Run bit which enables the clocks to the PWM submodule. This function can start multiple submodules at the same time.
- Parameters:
base – PWM peripheral base address
subModulesToStart – PWM submodules to start. This is a logical OR of members of the enumeration pwm_module_control_t
-
static inline void PWM_StopTimer(PWM_Type *base, uint8_t subModulesToStop)
Stops the PWM counter for a single or multiple submodules.
Clears the Run bit which resets the submodule’s counter. This function can stop multiple submodules at the same time.
- Parameters:
base – PWM peripheral base address
subModulesToStop – PWM submodules to stop. This is a logical OR of members of the enumeration pwm_module_control_t
-
FSL_PWM_DRIVER_VERSION
Version 2.9.0
-
enum _pwm_submodule
List of PWM submodules.
Values:
-
enumerator kPWM_Module_0
Submodule 0
-
enumerator kPWM_Module_1
Submodule 1
-
enumerator kPWM_Module_2
Submodule 2
-
enumerator kPWM_Module_0
-
enum _pwm_channels
List of PWM channels in each module.
Values:
-
enumerator kPWM_PwmB
-
enumerator kPWM_PwmA
-
enumerator kPWM_PwmX
-
enumerator kPWM_PwmB
-
enum _pwm_value_register
List of PWM value registers.
Values:
-
enumerator kPWM_ValueRegister_0
PWM Value0 register
-
enumerator kPWM_ValueRegister_1
PWM Value1 register
-
enumerator kPWM_ValueRegister_2
PWM Value2 register
-
enumerator kPWM_ValueRegister_3
PWM Value3 register
-
enumerator kPWM_ValueRegister_4
PWM Value4 register
-
enumerator kPWM_ValueRegister_5
PWM Value5 register
-
enumerator kPWM_ValueRegister_0
-
enum _pwm_value_register_mask
List of PWM value registers mask.
Values:
-
enumerator kPWM_ValueRegisterMask_0
PWM Value0 register mask
-
enumerator kPWM_ValueRegisterMask_1
PWM Value1 register mask
-
enumerator kPWM_ValueRegisterMask_2
PWM Value2 register mask
-
enumerator kPWM_ValueRegisterMask_3
PWM Value3 register mask
-
enumerator kPWM_ValueRegisterMask_4
PWM Value4 register mask
-
enumerator kPWM_ValueRegisterMask_5
PWM Value5 register mask
-
enumerator kPWM_ValueRegisterMask_0
-
enum _pwm_clock_source
PWM clock source selection.
Values:
-
enumerator kPWM_BusClock
The IPBus clock is used as the clock
-
enumerator kPWM_ExternalClock
EXT_CLK is used as the clock
-
enumerator kPWM_Submodule0Clock
Clock of the submodule 0 (AUX_CLK) is used as the source clock
-
enumerator kPWM_BusClock
-
enum _pwm_clock_prescale
PWM prescaler factor selection for clock source.
Values:
-
enumerator kPWM_Prescale_Divide_1
PWM clock frequency = fclk/1
-
enumerator kPWM_Prescale_Divide_2
PWM clock frequency = fclk/2
-
enumerator kPWM_Prescale_Divide_4
PWM clock frequency = fclk/4
-
enumerator kPWM_Prescale_Divide_8
PWM clock frequency = fclk/8
-
enumerator kPWM_Prescale_Divide_16
PWM clock frequency = fclk/16
-
enumerator kPWM_Prescale_Divide_32
PWM clock frequency = fclk/32
-
enumerator kPWM_Prescale_Divide_64
PWM clock frequency = fclk/64
-
enumerator kPWM_Prescale_Divide_128
PWM clock frequency = fclk/128
-
enumerator kPWM_Prescale_Divide_1
-
enum _pwm_force_output_trigger
Options that can trigger a PWM FORCE_OUT.
Values:
-
enumerator kPWM_Force_Local
The local force signal, CTRL2[FORCE], from the submodule is used to force updates
-
enumerator kPWM_Force_Master
The master force signal from submodule 0 is used to force updates
-
enumerator kPWM_Force_LocalReload
The local reload signal from this submodule is used to force updates without regard to the state of LDOK
-
enumerator kPWM_Force_MasterReload
The master reload signal from submodule 0 is used to force updates if LDOK is set
-
enumerator kPWM_Force_LocalSync
The local sync signal from this submodule is used to force updates
-
enumerator kPWM_Force_MasterSync
The master sync signal from submodule0 is used to force updates
-
enumerator kPWM_Force_External
The external force signal, EXT_FORCE, from outside the PWM module causes updates
-
enumerator kPWM_Force_ExternalSync
The external sync signal, EXT_SYNC, from outside the PWM module causes updates
-
enumerator kPWM_Force_Local
-
enum _pwm_output_state
PWM channel output status.
Values:
-
enumerator kPWM_HighState
The output state of PWM channel is high
-
enumerator kPWM_LowState
The output state of PWM channel is low
-
enumerator kPWM_NormalState
The output state of PWM channel is normal
-
enumerator kPWM_InvertState
The output state of PWM channel is invert
-
enumerator kPWM_MaskState
The output state of PWM channel is mask
-
enumerator kPWM_HighState
-
enum _pwm_init_source
PWM counter initialization options.
Values:
-
enumerator kPWM_Initialize_LocalSync
Local sync causes initialization
-
enumerator kPWM_Initialize_MasterReload
Master reload from submodule 0 causes initialization
-
enumerator kPWM_Initialize_MasterSync
Master sync from submodule 0 causes initialization
-
enumerator kPWM_Initialize_ExtSync
EXT_SYNC causes initialization
-
enumerator kPWM_Initialize_LocalSync
-
enum _pwm_load_frequency
PWM load frequency selection.
Values:
-
enumerator kPWM_LoadEveryOportunity
Every PWM opportunity
-
enumerator kPWM_LoadEvery2Oportunity
Every 2 PWM opportunities
-
enumerator kPWM_LoadEvery3Oportunity
Every 3 PWM opportunities
-
enumerator kPWM_LoadEvery4Oportunity
Every 4 PWM opportunities
-
enumerator kPWM_LoadEvery5Oportunity
Every 5 PWM opportunities
-
enumerator kPWM_LoadEvery6Oportunity
Every 6 PWM opportunities
-
enumerator kPWM_LoadEvery7Oportunity
Every 7 PWM opportunities
-
enumerator kPWM_LoadEvery8Oportunity
Every 8 PWM opportunities
-
enumerator kPWM_LoadEvery9Oportunity
Every 9 PWM opportunities
-
enumerator kPWM_LoadEvery10Oportunity
Every 10 PWM opportunities
-
enumerator kPWM_LoadEvery11Oportunity
Every 11 PWM opportunities
-
enumerator kPWM_LoadEvery12Oportunity
Every 12 PWM opportunities
-
enumerator kPWM_LoadEvery13Oportunity
Every 13 PWM opportunities
-
enumerator kPWM_LoadEvery14Oportunity
Every 14 PWM opportunities
-
enumerator kPWM_LoadEvery15Oportunity
Every 15 PWM opportunities
-
enumerator kPWM_LoadEvery16Oportunity
Every 16 PWM opportunities
-
enumerator kPWM_LoadEveryOportunity
-
enum _pwm_fault_input
List of PWM fault selections.
Values:
-
enumerator kPWM_Fault_0
Fault 0 input pin
-
enumerator kPWM_Fault_1
Fault 1 input pin
-
enumerator kPWM_Fault_2
Fault 2 input pin
-
enumerator kPWM_Fault_3
Fault 3 input pin
-
enumerator kPWM_Fault_0
-
enum _pwm_fault_disable
List of PWM fault disable mapping selections.
Values:
-
enumerator kPWM_FaultDisable_0
Fault 0 disable mapping
-
enumerator kPWM_FaultDisable_1
Fault 1 disable mapping
-
enumerator kPWM_FaultDisable_2
Fault 2 disable mapping
-
enumerator kPWM_FaultDisable_3
Fault 3 disable mapping
-
enumerator kPWM_FaultDisable_0
-
enum _pwm_fault_channels
List of PWM fault channels.
Values:
-
enumerator kPWM_faultchannel_0
-
enumerator kPWM_faultchannel_1
-
enumerator kPWM_faultchannel_0
-
enum _pwm_input_capture_edge
PWM capture edge select.
Values:
-
enumerator kPWM_Disable
Disabled
-
enumerator kPWM_FallingEdge
Capture on falling edge only
-
enumerator kPWM_RisingEdge
Capture on rising edge only
-
enumerator kPWM_RiseAndFallEdge
Capture on rising or falling edge
-
enumerator kPWM_Disable
-
enum _pwm_force_signal
PWM output options when a FORCE_OUT signal is asserted.
Values:
-
enumerator kPWM_UsePwm
Generated PWM signal is used by the deadtime logic.
-
enumerator kPWM_InvertedPwm
Inverted PWM signal is used by the deadtime logic.
-
enumerator kPWM_SoftwareControl
Software controlled value is used by the deadtime logic.
-
enumerator kPWM_UseExternal
PWM_EXTA signal is used by the deadtime logic.
-
enumerator kPWM_UsePwm
-
enum _pwm_chnl_pair_operation
Options available for the PWM A & B pair operation.
Values:
-
enumerator kPWM_Independent
PWM A & PWM B operate as 2 independent channels
-
enumerator kPWM_ComplementaryPwmA
PWM A & PWM B are complementary channels, PWM A generates the signal
-
enumerator kPWM_ComplementaryPwmB
PWM A & PWM B are complementary channels, PWM B generates the signal
-
enumerator kPWM_Independent
-
enum _pwm_register_reload
Options available on how to load the buffered-registers with new values.
Values:
-
enumerator kPWM_ReloadImmediate
Buffered-registers get loaded with new values as soon as LDOK bit is set
-
enumerator kPWM_ReloadPwmHalfCycle
Registers loaded on a PWM half cycle
-
enumerator kPWM_ReloadPwmFullCycle
Registers loaded on a PWM full cycle
-
enumerator kPWM_ReloadPwmHalfAndFullCycle
Registers loaded on a PWM half & full cycle
-
enumerator kPWM_ReloadImmediate
-
enum _pwm_fault_recovery_mode
Options available on how to re-enable the PWM output when recovering from a fault.
Values:
-
enumerator kPWM_NoRecovery
PWM output will stay inactive
-
enumerator kPWM_RecoverHalfCycle
PWM output re-enabled at the first half cycle
-
enumerator kPWM_RecoverFullCycle
PWM output re-enabled at the first full cycle
-
enumerator kPWM_RecoverHalfAndFullCycle
PWM output re-enabled at the first half or full cycle
-
enumerator kPWM_NoRecovery
-
enum _pwm_interrupt_enable
List of PWM interrupt options.
Values:
-
enumerator kPWM_CompareVal0InterruptEnable
PWM VAL0 compare interrupt
-
enumerator kPWM_CompareVal1InterruptEnable
PWM VAL1 compare interrupt
-
enumerator kPWM_CompareVal2InterruptEnable
PWM VAL2 compare interrupt
-
enumerator kPWM_CompareVal3InterruptEnable
PWM VAL3 compare interrupt
-
enumerator kPWM_CompareVal4InterruptEnable
PWM VAL4 compare interrupt
-
enumerator kPWM_CompareVal5InterruptEnable
PWM VAL5 compare interrupt
-
enumerator kPWM_CaptureX0InterruptEnable
PWM capture X0 interrupt
-
enumerator kPWM_CaptureX1InterruptEnable
PWM capture X1 interrupt
-
enumerator kPWM_CaptureB0InterruptEnable
PWM capture B0 interrupt
-
enumerator kPWM_CaptureB1InterruptEnable
PWM capture B1 interrupt
-
enumerator kPWM_CaptureA0InterruptEnable
PWM capture A0 interrupt
-
enumerator kPWM_CaptureA1InterruptEnable
PWM capture A1 interrupt
-
enumerator kPWM_ReloadInterruptEnable
PWM reload interrupt
-
enumerator kPWM_ReloadErrorInterruptEnable
PWM reload error interrupt
-
enumerator kPWM_Fault0InterruptEnable
PWM fault 0 interrupt
-
enumerator kPWM_Fault1InterruptEnable
PWM fault 1 interrupt
-
enumerator kPWM_Fault2InterruptEnable
PWM fault 2 interrupt
-
enumerator kPWM_Fault3InterruptEnable
PWM fault 3 interrupt
-
enumerator kPWM_CompareVal0InterruptEnable
-
enum _pwm_status_flags
List of PWM status flags.
Values:
-
enumerator kPWM_CompareVal0Flag
PWM VAL0 compare flag
-
enumerator kPWM_CompareVal1Flag
PWM VAL1 compare flag
-
enumerator kPWM_CompareVal2Flag
PWM VAL2 compare flag
-
enumerator kPWM_CompareVal3Flag
PWM VAL3 compare flag
-
enumerator kPWM_CompareVal4Flag
PWM VAL4 compare flag
-
enumerator kPWM_CompareVal5Flag
PWM VAL5 compare flag
-
enumerator kPWM_CaptureX0Flag
PWM capture X0 flag
-
enumerator kPWM_CaptureX1Flag
PWM capture X1 flag
-
enumerator kPWM_CaptureB0Flag
PWM capture B0 flag
-
enumerator kPWM_CaptureB1Flag
PWM capture B1 flag
-
enumerator kPWM_CaptureA0Flag
PWM capture A0 flag
-
enumerator kPWM_CaptureA1Flag
PWM capture A1 flag
-
enumerator kPWM_ReloadFlag
PWM reload flag
-
enumerator kPWM_ReloadErrorFlag
PWM reload error flag
-
enumerator kPWM_RegUpdatedFlag
PWM registers updated flag
-
enumerator kPWM_Fault0Flag
PWM fault 0 flag
-
enumerator kPWM_Fault1Flag
PWM fault 1 flag
-
enumerator kPWM_Fault2Flag
PWM fault 2 flag
-
enumerator kPWM_Fault3Flag
PWM fault 3 flag
-
enumerator kPWM_CompareVal0Flag
-
enum _pwm_dma_enable
List of PWM DMA options.
Values:
-
enumerator kPWM_CaptureX0DMAEnable
PWM capture X0 DMA
-
enumerator kPWM_CaptureX1DMAEnable
PWM capture X1 DMA
-
enumerator kPWM_CaptureB0DMAEnable
PWM capture B0 DMA
-
enumerator kPWM_CaptureB1DMAEnable
PWM capture B1 DMA
-
enumerator kPWM_CaptureA0DMAEnable
PWM capture A0 DMA
-
enumerator kPWM_CaptureA1DMAEnable
PWM capture A1 DMA
-
enumerator kPWM_CaptureX0DMAEnable
-
enum _pwm_dma_source_select
List of PWM capture DMA enable source select.
Values:
-
enumerator kPWM_DMARequestDisable
Read DMA requests disabled
-
enumerator kPWM_DMAWatermarksEnable
Exceeding a FIFO watermark sets the DMA read request
-
enumerator kPWM_DMALocalSync
A local sync (VAL1 matches counter) sets the read DMA request
-
enumerator kPWM_DMALocalReload
A local reload (STS[RF] being set) sets the read DMA request
-
enumerator kPWM_DMARequestDisable
-
enum _pwm_watermark_control
PWM FIFO Watermark AND Control.
Values:
-
enumerator kPWM_FIFOWatermarksOR
Selected FIFO watermarks are OR’ed together
-
enumerator kPWM_FIFOWatermarksAND
Selected FIFO watermarks are AND’ed together
-
enumerator kPWM_FIFOWatermarksOR
-
enum _pwm_mode
PWM operation mode.
Values:
-
enumerator kPWM_SignedCenterAligned
Signed center-aligned
-
enumerator kPWM_CenterAligned
Unsigned cente-aligned
-
enumerator kPWM_SignedEdgeAligned
Signed edge-aligned
-
enumerator kPWM_EdgeAligned
Unsigned edge-aligned
-
enumerator kPWM_SignedCenterAligned
-
enum _pwm_level_select
PWM output pulse mode, high-true or low-true.
Values:
-
enumerator kPWM_HighTrue
High level represents “on” or “active” state
-
enumerator kPWM_LowTrue
Low level represents “on” or “active” state
-
enumerator kPWM_HighTrue
-
enum _pwm_fault_state
PWM output fault status.
Values:
-
enumerator kPWM_PwmFaultState0
Output is forced to logic 0 state prior to consideration of output polarity control.
-
enumerator kPWM_PwmFaultState1
Output is forced to logic 1 state prior to consideration of output polarity control.
-
enumerator kPWM_PwmFaultState2
Output is tristated.
-
enumerator kPWM_PwmFaultState3
Output is tristated.
-
enumerator kPWM_PwmFaultState0
-
enum _pwm_reload_source_select
PWM reload source select.
Values:
-
enumerator kPWM_LocalReload
The local reload signal is used to reload registers
-
enumerator kPWM_MasterReload
The master reload signal (from submodule 0) is used to reload
-
enumerator kPWM_LocalReload
-
enum _pwm_fault_clear
PWM fault clearing options.
Values:
-
enumerator kPWM_Automatic
Automatic fault clearing
-
enumerator kPWM_ManualNormal
Manual fault clearing with no fault safety mode
-
enumerator kPWM_ManualSafety
Manual fault clearing with fault safety mode
-
enumerator kPWM_Automatic
-
enum _pwm_module_control
Options for submodule master control operation.
Values:
-
enumerator kPWM_Control_Module_0
Control submodule 0’s start/stop,buffer reload operation
-
enumerator kPWM_Control_Module_1
Control submodule 1’s start/stop,buffer reload operation
-
enumerator kPWM_Control_Module_2
Control submodule 2’s start/stop,buffer reload operation
-
enumerator kPWM_Control_Module_3
Control submodule 3’s start/stop,buffer reload operation
-
enumerator kPWM_Control_Module_0
-
typedef enum _pwm_submodule pwm_submodule_t
List of PWM submodules.
-
typedef enum _pwm_channels pwm_channels_t
List of PWM channels in each module.
-
typedef enum _pwm_value_register pwm_value_register_t
List of PWM value registers.
-
typedef enum _pwm_clock_source pwm_clock_source_t
PWM clock source selection.
-
typedef enum _pwm_clock_prescale pwm_clock_prescale_t
PWM prescaler factor selection for clock source.
-
typedef enum _pwm_force_output_trigger pwm_force_output_trigger_t
Options that can trigger a PWM FORCE_OUT.
-
typedef enum _pwm_output_state pwm_output_state_t
PWM channel output status.
-
typedef enum _pwm_init_source pwm_init_source_t
PWM counter initialization options.
-
typedef enum _pwm_load_frequency pwm_load_frequency_t
PWM load frequency selection.
-
typedef enum _pwm_fault_input pwm_fault_input_t
List of PWM fault selections.
-
typedef enum _pwm_fault_disable pwm_fault_disable_t
List of PWM fault disable mapping selections.
-
typedef enum _pwm_fault_channels pwm_fault_channels_t
List of PWM fault channels.
-
typedef enum _pwm_input_capture_edge pwm_input_capture_edge_t
PWM capture edge select.
-
typedef enum _pwm_force_signal pwm_force_signal_t
PWM output options when a FORCE_OUT signal is asserted.
-
typedef enum _pwm_chnl_pair_operation pwm_chnl_pair_operation_t
Options available for the PWM A & B pair operation.
-
typedef enum _pwm_register_reload pwm_register_reload_t
Options available on how to load the buffered-registers with new values.
-
typedef enum _pwm_fault_recovery_mode pwm_fault_recovery_mode_t
Options available on how to re-enable the PWM output when recovering from a fault.
-
typedef enum _pwm_interrupt_enable pwm_interrupt_enable_t
List of PWM interrupt options.
-
typedef enum _pwm_status_flags pwm_status_flags_t
List of PWM status flags.
-
typedef enum _pwm_dma_enable pwm_dma_enable_t
List of PWM DMA options.
-
typedef enum _pwm_dma_source_select pwm_dma_source_select_t
List of PWM capture DMA enable source select.
-
typedef enum _pwm_watermark_control pwm_watermark_control_t
PWM FIFO Watermark AND Control.
-
typedef enum _pwm_mode pwm_mode_t
PWM operation mode.
-
typedef enum _pwm_level_select pwm_level_select_t
PWM output pulse mode, high-true or low-true.
-
typedef enum _pwm_fault_state pwm_fault_state_t
PWM output fault status.
-
typedef enum _pwm_reload_source_select pwm_reload_source_select_t
PWM reload source select.
-
typedef enum _pwm_fault_clear pwm_fault_clear_t
PWM fault clearing options.
-
typedef enum _pwm_module_control pwm_module_control_t
Options for submodule master control operation.
-
typedef struct _pwm_signal_param pwm_signal_param_t
Structure for the user to define the PWM signal characteristics.
-
typedef struct _pwm_config pwm_config_t
PWM config structure.
This structure holds the configuration settings for the PWM peripheral. To initialize this structure to reasonable defaults, call the PWM_GetDefaultConfig() function and pass a pointer to your config structure instance.
The config struct can be made const so it resides in flash
-
typedef struct _pwm_fault_input_filter_param pwm_fault_input_filter_param_t
Structure for the user to configure the fault input filter.
-
typedef struct _pwm_fault_param pwm_fault_param_t
Structure is used to hold the parameters to configure a PWM fault.
-
typedef struct _pwm_input_capture_param pwm_input_capture_param_t
Structure is used to hold parameters to configure the capture capability of a signal pin.
-
void PWM_SetupInputCapture(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel, const pwm_input_capture_param_t *inputCaptureParams)
Sets up the PWM input capture.
Each PWM submodule has 3 pins that can be configured for use as input capture pins. This function sets up the capture parameters for each pin and enables the pin for input capture operation.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmChannel – Channel in the submodule to setup
inputCaptureParams – Parameters passed in to set up the input pin
-
void PWM_SetupFaultInputFilter(PWM_Type *base, const pwm_fault_input_filter_param_t *faultInputFilterParams)
Sets up the PWM fault input filter.
- Parameters:
base – PWM peripheral base address
faultInputFilterParams – Parameters passed in to set up the fault input filter.
-
void PWM_SetupFaults(PWM_Type *base, pwm_fault_input_t faultNum, const pwm_fault_param_t *faultParams)
Sets up the PWM fault protection.
PWM has 4 fault inputs.
- Parameters:
base – PWM peripheral base address
faultNum – PWM fault to configure.
faultParams – Pointer to the PWM fault config structure
-
void PWM_FaultDefaultConfig(pwm_fault_param_t *config)
Fill in the PWM fault config struct with the default settings.
The default values are:
config->faultClearingMode = kPWM_Automatic; config->faultLevel = false; config->enableCombinationalPath = true; config->recoverMode = kPWM_NoRecovery;
- Parameters:
config – Pointer to user’s PWM fault config structure.
-
void PWM_SetupForceSignal(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel, pwm_force_signal_t mode)
Selects the signal to output on a PWM pin when a FORCE_OUT signal is asserted.
The user specifies which channel to configure by supplying the submodule number and whether to modify PWM A or PWM B within that submodule.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmChannel – Channel to configure
mode – Signal to output when a FORCE_OUT is triggered
-
static inline void PWM_SetVALxValue(PWM_Type *base, pwm_submodule_t subModule, pwm_value_register_t valueRegister, uint16_t value)
Set the PWM VALx registers.
This function allows the user to write value into VAL registers directly. And it will destroying the PWM clock period set by the PWM_SetupPwm()/PWM_SetupPwmPhaseShift() functions. Due to VALx registers are bufferd, the new value will not active uless call PWM_SetPwmLdok() and the reload point is reached.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
valueRegister – VALx register that will be writen new value
value – Value that will been write into VALx register
-
static inline uint16_t PWM_GetVALxValue(PWM_Type *base, pwm_submodule_t subModule, pwm_value_register_t valueRegister)
Get the PWM VALx registers.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
valueRegister – VALx register that will be read value
- Returns:
The VALx register value
-
static inline void PWM_OutputTriggerEnable(PWM_Type *base, pwm_submodule_t subModule, pwm_value_register_t valueRegister, bool activate)
Enables or disables the PWM output trigger.
This function allows the user to enable or disable the PWM trigger. The PWM has 2 triggers. Trigger 0 is activated when the counter matches VAL 0, VAL 2, or VAL 4 register. Trigger 1 is activated when the counter matches VAL 1, VAL 3, or VAL 5 register.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
valueRegister – Value register that will activate the trigger
activate – true: Enable the trigger; false: Disable the trigger
-
static inline void PWM_ActivateOutputTrigger(PWM_Type *base, pwm_submodule_t subModule, uint16_t valueRegisterMask)
Enables the PWM output trigger.
This function allows the user to enable one or more (VAL0-5) PWM trigger.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
valueRegisterMask – Value register mask that will activate one or more (VAL0-5) trigger enumeration _pwm_value_register_mask
-
static inline void PWM_DeactivateOutputTrigger(PWM_Type *base, pwm_submodule_t subModule, uint16_t valueRegisterMask)
Disables the PWM output trigger.
This function allows the user to disables one or more (VAL0-5) PWM trigger.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
valueRegisterMask – Value register mask that will Deactivate one or more (VAL0-5) trigger enumeration _pwm_value_register_mask
-
static inline void PWM_SetupSwCtrlOut(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel, bool value)
Sets the software control output for a pin to high or low.
The user specifies which channel to modify by supplying the submodule number and whether to modify PWM A or PWM B within that submodule.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmChannel – Channel to configure
value – true: Supply a logic 1, false: Supply a logic 0.
-
static inline void PWM_SetPwmLdok(PWM_Type *base, uint8_t subModulesToUpdate, bool value)
Sets or clears the PWM LDOK bit on a single or multiple submodules.
Set LDOK bit to load buffered values into CTRL[PRSC] and the INIT, FRACVAL and VAL registers. The values are loaded immediately if kPWM_ReloadImmediate option was choosen during config. Else the values are loaded at the next PWM reload point. This function can issue the load command to multiple submodules at the same time.
- Parameters:
base – PWM peripheral base address
subModulesToUpdate – PWM submodules to update with buffered values. This is a logical OR of members of the enumeration pwm_module_control_t
value – true: Set LDOK bit for the submodule list; false: Clear LDOK bit
-
static inline void PWM_SetPwmFaultState(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel, pwm_fault_state_t faultState)
Set PWM output fault status.
These bits determine the fault state for the PWM_A output in fault conditions and STOP mode. It may also define the output state in WAIT and DEBUG modes depending on the settings of CTRL2[WAITEN] and CTRL2[DBGEN]. This function can update PWM output fault status.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmChannel – Channel to configure
faultState – PWM output fault status
-
static inline void PWM_SetupFaultDisableMap(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel, pwm_fault_channels_t pwm_fault_channels, uint16_t value)
Set PWM fault disable mapping.
Each of the four bits of this read/write field is one-to-one associated with the four FAULTx inputs of fault channel 0/1. The PWM output will be turned off if there is a logic 1 on an FAULTx input and a 1 in the corresponding bit of this field. A reset sets all bits in this field.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmChannel – PWM channel to configure
pwm_fault_channels – PWM fault channel to configure
value – Fault disable mapping mask value enumeration pwm_fault_disable_t
-
static inline void PWM_OutputEnable(PWM_Type *base, pwm_channels_t pwmChannel, pwm_submodule_t subModule)
Set PWM output enable.
This feature allows the user to enable the PWM Output. Recommend to invoke this API after PWM and fault configuration. But invoke this API before configure MCTRL register is okay, such as set LDOK or start timer.
- Parameters:
base – PWM peripheral base address
pwmChannel – PWM channel to configure
subModule – PWM submodule to configure
-
static inline void PWM_OutputDisable(PWM_Type *base, pwm_channels_t pwmChannel, pwm_submodule_t subModule)
Set PWM output disable.
This feature allows the user to disable the PWM output. Recommend to invoke this API after PWM and fault configuration. But invoke this API before configure MCTRL register is okay, such as set LDOK or start timer.
- Parameters:
base – PWM peripheral base address
pwmChannel – PWM channel to configure
subModule – PWM submodule to configure
-
uint8_t PWM_GetPwmChannelState(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel)
Get the dutycycle value.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmChannel – PWM channel to configure
- Returns:
Current channel dutycycle value.
-
status_t PWM_SetOutputToIdle(PWM_Type *base, pwm_channels_t pwmChannel, pwm_submodule_t subModule, bool idleStatus)
Set PWM output in idle status (high or low).
Note
This API should call after PWM_SetupPwm() APIs, and PWMX submodule is not supported.
- Parameters:
base – PWM peripheral base address
pwmChannel – PWM channel to configure
subModule – PWM submodule to configure
idleStatus – True: PWM output is high in idle status; false: PWM output is low in idle status.
- Returns:
kStatus_Fail if there was error setting up the signal; kStatus_Success if set output idle success
-
void PWM_SetClockMode(PWM_Type *base, pwm_submodule_t subModule, pwm_clock_prescale_t prescaler)
Set the pwm submodule prescaler.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
prescaler – Set prescaler value
-
void PWM_SetPwmForceOutputToZero(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel, bool forcetozero)
This function enables-disables the forcing of the output of a given eFlexPwm channel to logic 0.
- Parameters:
base – PWM peripheral base address
pwmChannel – PWM channel to configure
subModule – PWM submodule to configure
forcetozero – True: Enable the pwm force output to zero; False: Disable the pwm output resumes normal function.
-
void PWM_SetChannelOutput(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel, pwm_output_state_t outputstate)
This function set the output state of the PWM pin as requested for the current cycle.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmChannel – PWM channel to configure
outputstate – Set pwm output state, see pwm_output_state_t.
-
status_t PWM_SetPhaseDelay(PWM_Type *base, pwm_channels_t pwmChannel, pwm_submodule_t subModule, uint16_t delayCycles)
This function set the phase delay from the master sync signal of submodule 0.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmChannel – PWM channel to configure
delayCycles – Number of cycles delayed from submodule 0.
- Returns:
kStatus_Fail if the number of delay cycles is set larger than the period defined in submodule 0; kStatus_Success if set phase delay success
-
static inline void PWM_SetFilterSampleCount(PWM_Type *base, pwm_channels_t pwmChannel, pwm_submodule_t subModule, uint8_t filterSampleCount)
This function set the number of consecutive samples that must agree prior to the input filter.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmChannel – PWM channel to configure
filterSampleCount – Number of consecutive samples.
-
static inline void PWM_SetFilterSamplePeriod(PWM_Type *base, pwm_channels_t pwmChannel, pwm_submodule_t subModule, uint8_t filterSamplePeriod)
This function set the sampling period of the fault pin input filter.
- Parameters:
base – PWM peripheral base address
subModule – PWM submodule to configure
pwmChannel – PWM channel to configure
filterSamplePeriod – Sampling period of input filter.
-
PWM_SUBMODULE_SWCONTROL_WIDTH
Number of bits per submodule for software output control
-
PWM_SUBMODULE_CHANNEL
Submodule channels include PWMA, PWMB, PWMX.
-
struct _pwm_signal_param
- #include <fsl_pwm.h>
Structure for the user to define the PWM signal characteristics.
Public Members
-
pwm_channels_t pwmChannel
PWM channel being configured; PWM A or PWM B
-
uint8_t dutyCyclePercent
PWM pulse width, value should be between 0 to 100 0=inactive signal(0% duty cycle)… 100=always active signal (100% duty cycle)
-
pwm_level_select_t level
PWM output active level select
-
uint16_t deadtimeValue
The deadtime value; only used if channel pair is operating in complementary mode
-
pwm_fault_state_t faultState
PWM output fault status
-
bool pwmchannelenable
Enable PWM output
-
pwm_channels_t pwmChannel
-
struct _pwm_config
- #include <fsl_pwm.h>
PWM config structure.
This structure holds the configuration settings for the PWM peripheral. To initialize this structure to reasonable defaults, call the PWM_GetDefaultConfig() function and pass a pointer to your config structure instance.
The config struct can be made const so it resides in flash
Public Members
-
bool enableDebugMode
true: PWM continues to run in debug mode; false: PWM is paused in debug mode
-
pwm_init_source_t initializationControl
Option to initialize the counter
-
pwm_clock_source_t clockSource
Clock source for the counter
-
pwm_clock_prescale_t prescale
Pre-scaler to divide down the clock
-
pwm_chnl_pair_operation_t pairOperation
Channel pair in indepedent or complementary mode
-
pwm_register_reload_t reloadLogic
PWM Reload logic setup
-
pwm_reload_source_select_t reloadSelect
Reload source select
-
pwm_load_frequency_t reloadFrequency
Specifies when to reload, used when user’s choice is not immediate reload
-
pwm_force_output_trigger_t forceTrigger
Specify which signal will trigger a FORCE_OUT
-
bool enableDebugMode
-
struct _pwm_fault_input_filter_param
- #include <fsl_pwm.h>
Structure for the user to configure the fault input filter.
Public Members
-
uint8_t faultFilterCount
Fault filter count
-
uint8_t faultFilterPeriod
Fault filter period;value of 0 will bypass the filter
-
bool faultGlitchStretch
Fault Glitch Stretch Enable: A logic 1 means that input fault signals will be stretched to at least 2 IPBus clock cycles
-
uint8_t faultFilterCount
-
struct _pwm_fault_param
- #include <fsl_pwm.h>
Structure is used to hold the parameters to configure a PWM fault.
Public Members
-
pwm_fault_clear_t faultClearingMode
Fault clearing mode to use
-
bool faultLevel
true: Logic 1 indicates fault; false: Logic 0 indicates fault
-
bool enableCombinationalPath
true: Combinational Path from fault input is enabled; false: No combination path is available
-
pwm_fault_recovery_mode_t recoverMode
Specify when to re-enable the PWM output
-
pwm_fault_clear_t faultClearingMode
-
struct _pwm_input_capture_param
- #include <fsl_pwm.h>
Structure is used to hold parameters to configure the capture capability of a signal pin.
Public Members
-
bool captureInputSel
true: Use the edge counter signal as source false: Use the raw input signal from the pin as source
-
uint8_t edgeCompareValue
Compare value, used only if edge counter is used as source
-
pwm_input_capture_edge_t edge0
Specify which edge causes a capture for input circuitry 0
-
pwm_input_capture_edge_t edge1
Specify which edge causes a capture for input circuitry 1
-
bool enableOneShotCapture
true: Use one-shot capture mode; false: Use free-running capture mode
-
uint8_t fifoWatermark
Watermark level for capture FIFO. The capture flags in the status register will set if the word count in the FIFO is greater than this watermark level
-
bool captureInputSel
PXP: Pixel Pipeline
-
void PXP_Init(PXP_Type *base)
Initialize the PXP.
This function enables the PXP peripheral clock, and resets the PXP registers to default status.
- Parameters:
base – PXP peripheral base address.
-
void PXP_Deinit(PXP_Type *base)
De-initialize the PXP.
This function disables the PXP peripheral clock.
- Parameters:
base – PXP peripheral base address.
-
void PXP_Reset(PXP_Type *base)
Reset the PXP.
This function resets the PXP peripheral registers to default status.
- Parameters:
base – PXP peripheral base address.
-
void PXP_ResetControl(PXP_Type *base)
Reset the PXP and the control register to initialized state.
- Parameters:
base – PXP peripheral base address.
-
static inline void PXP_Start(PXP_Type *base)
Start process.
Start PXP process using current configuration.
- Parameters:
base – PXP peripheral base address.
-
static inline void PXP_EnableLcdHandShake(PXP_Type *base, bool enable)
Enable or disable LCD hand shake.
- Parameters:
base – PXP peripheral base address.
enable – True to enable, false to disable.
-
static inline void PXP_EnableContinousRun(PXP_Type *base, bool enable)
Enable or disable continous run.
If continous run not enabled, PXP_Start starts the PXP process. When completed, PXP enters idle mode and flag kPXP_CompleteFlag asserts.
If continous run enabled, the PXP will repeat based on the current configuration register settings.
- Parameters:
base – PXP peripheral base address.
enable – True to enable, false to disable.
-
static inline void PXP_SetProcessBlockSize(PXP_Type *base, pxp_block_size_t size)
Set the PXP processing block size.
This function chooses the pixel block size that PXP using during process. Larger block size means better performace, but be careful that when PXP is rotating, the output must be divisible by the block size selected.
- Parameters:
base – PXP peripheral base address.
size – The pixel block size.
-
static inline void PXP_EnableProcessEngine(PXP_Type *base, uint32_t mask, bool enable)
Enables or disables PXP engines in the process flow.
- Parameters:
base – PXP peripheral base address.
mask – The engines to enable. Logical OR of pxp_process_engine_name_t.
enable – true to enable, false to disable.
-
static inline uint32_t PXP_GetStatusFlags(PXP_Type *base)
Gets PXP status flags.
This function gets all PXP status flags. The flags are returned as the logical OR value of the enumerators _pxp_flags. To check a specific status, compare the return value with enumerators in _pxp_flags. For example, to check whether the PXP has completed process, use like this:
if (kPXP_CompleteFlag & PXP_GetStatusFlags(PXP)) { ... }
- Parameters:
base – PXP peripheral base address.
- Returns:
PXP status flags which are OR’ed by the enumerators in the _pxp_flags.
-
static inline void PXP_ClearStatusFlags(PXP_Type *base, uint32_t statusMask)
Clears status flags with the provided mask.
This function clears PXP status flags with a provided mask.
- Parameters:
base – PXP peripheral base address.
statusMask – The status flags to be cleared; it is logical OR value of _pxp_flags.
-
static inline uint8_t PXP_GetAxiErrorId(PXP_Type *base, uint8_t axiIndex)
Gets the AXI ID of the failing bus operation.
- Parameters:
base – PXP peripheral base address.
axiIndex – Whitch AXI to get
0: AXI0
1: AXI1
- Returns:
The AXI ID of the failing bus operation.
-
static inline void PXP_EnableInterrupts(PXP_Type *base, uint32_t mask)
Enables PXP interrupts according to the provided mask.
This function enables the PXP interrupts according to the provided mask. The mask is a logical OR of enumeration members. See _pxp_interrupt_enable. For example, to enable PXP process complete interrupt and command loaded interrupt, do the following.
PXP_EnableInterrupts(PXP, kPXP_CommandLoadInterruptEnable | kPXP_CompleteInterruptEnable);
- Parameters:
base – PXP peripheral base address.
mask – The interrupts to enable. Logical OR of _pxp_interrupt_enable.
-
static inline void PXP_DisableInterrupts(PXP_Type *base, uint32_t mask)
Disables PXP interrupts according to the provided mask.
This function disables the PXP interrupts according to the provided mask. The mask is a logical OR of enumeration members. See _pxp_interrupt_enable.
- Parameters:
base – PXP peripheral base address.
mask – The interrupts to disable. Logical OR of _pxp_interrupt_enable.
-
void PXP_SetAlphaSurfaceBufferConfig(PXP_Type *base, const pxp_as_buffer_config_t *config)
Set the alpha surface input buffer configuration.
- Parameters:
base – PXP peripheral base address.
config – Pointer to the configuration.
-
void PXP_SetAlphaSurfaceBlendConfig(PXP_Type *base, const pxp_as_blend_config_t *config)
Set the alpha surface blending configuration.
- Parameters:
base – PXP peripheral base address.
config – Pointer to the configuration structure.
-
void PXP_SetAlphaSurfaceBlendSecondaryConfig(PXP_Type *base, const pxp_as_blend_secondary_config_t *config)
Set the alpha surface blending configuration for the secondary engine.
- Parameters:
base – PXP peripheral base address.
config – Pointer to the configuration structure.
-
void PXP_SetAlphaSurfaceOverlayColorKey(PXP_Type *base, uint8_t num, uint32_t colorKeyLow, uint32_t colorKeyHigh)
Set the alpha surface overlay color key.
If a pixel in the current overlay image with a color that falls in the range from the
colorKeyLow
tocolorKeyHigh
range, it will use the process surface pixel value for that location. If no PS image is present or if the PS image also matches its colorkey range, the PS background color is used.Note
Colorkey operations are higher priority than alpha or ROP operations
- Parameters:
base – PXP peripheral base address.
num – instance number. 0 for alpha engine A, 1 for alpha engine B.
colorKeyLow – Color key low range.
colorKeyHigh – Color key high range.
-
static inline void PXP_EnableAlphaSurfaceOverlayColorKey(PXP_Type *base, uint32_t num, bool enable)
Enable or disable the alpha surface color key.
- Parameters:
base – PXP peripheral base address.
num – instance number. 0 for alpha engine A, 1 for alpha engine B.
enable – True to enable, false to disable.
-
void PXP_SetAlphaSurfacePosition(PXP_Type *base, uint16_t upperLeftX, uint16_t upperLeftY, uint16_t lowerRightX, uint16_t lowerRightY)
Set the alpha surface position in output buffer.
- Parameters:
base – PXP peripheral base address.
upperLeftX – X of the upper left corner.
upperLeftY – Y of the upper left corner.
lowerRightX – X of the lower right corner.
lowerRightY – Y of the lower right corner.
-
static inline void PXP_SetProcessSurfaceBackGroundColor(PXP_Type *base, uint8_t num, uint32_t backGroundColor)
Set the back ground color of PS.
- Parameters:
base – PXP peripheral base address.
num – instance number. 0 for alpha engine A, 1 for alpha engine B.
backGroundColor – Pixel value of the background color.
-
void PXP_SetProcessSurfaceBufferConfig(PXP_Type *base, const pxp_ps_buffer_config_t *config)
Set the process surface input buffer configuration.
- Parameters:
base – PXP peripheral base address.
config – Pointer to the configuration.
-
void PXP_SetProcessSurfaceScaler(PXP_Type *base, uint16_t inputWidth, uint16_t inputHeight, uint16_t outputWidth, uint16_t outputHeight)
Set the process surface scaler configuration.
The valid down scale fact is 1/(2^12) ~ 16.
- Parameters:
base – PXP peripheral base address.
inputWidth – Input image width.
inputHeight – Input image height.
outputWidth – Output image width.
outputHeight – Output image height.
-
void PXP_SetProcessSurfacePosition(PXP_Type *base, uint16_t upperLeftX, uint16_t upperLeftY, uint16_t lowerRightX, uint16_t lowerRightY)
Set the process surface position in output buffer.
- Parameters:
base – PXP peripheral base address.
upperLeftX – X of the upper left corner.
upperLeftY – Y of the upper left corner.
lowerRightX – X of the lower right corner.
lowerRightY – Y of the lower right corner.
-
void PXP_SetProcessSurfaceColorKey(PXP_Type *base, uint8_t num, uint32_t colorKeyLow, uint32_t colorKeyHigh)
Set the process surface color key.
If the PS image matches colorkey range, the PS background color is output. Set
colorKeyLow
to 0xFFFFFFFF and p colorKeyHigh to 0 will disable the colorkeying.- Parameters:
base – PXP peripheral base address.
num – instance number. 0 for alpha engine A, 1 for alpha engine B.
colorKeyLow – Color key low range.
colorKeyHigh – Color key high range.
-
static inline void PXP_SetProcessSurfaceYUVFormat(PXP_Type *base, pxp_ps_yuv_format_t format)
Set the process surface input pixel format YUV or YCbCr.
If process surface input pixel format is YUV and CSC1 is not enabled, in other words, the process surface output pixel format is also YUV, then this function should be called to set whether input pixel format is YUV or YCbCr.
- Parameters:
base – PXP peripheral base address.
format – The YUV format.
-
void PXP_SetOutputBufferConfig(PXP_Type *base, const pxp_output_buffer_config_t *config)
Set the PXP outpt buffer configuration.
- Parameters:
base – PXP peripheral base address.
config – Pointer to the configuration.
-
static inline void PXP_SetOverwrittenAlphaValue(PXP_Type *base, uint8_t alpha)
Set the global overwritten alpha value.
If global overwritten alpha is enabled, the alpha component in output buffer pixels will be overwritten, otherwise the computed alpha value is used.
- Parameters:
base – PXP peripheral base address.
alpha – The alpha value.
-
static inline void PXP_EnableOverWrittenAlpha(PXP_Type *base, bool enable)
Enable or disable the global overwritten alpha value.
If global overwritten alpha is enabled, the alpha component in output buffer pixels will be overwritten, otherwise the computed alpha value is used.
- Parameters:
base – PXP peripheral base address.
enable – True to enable, false to disable.
-
static inline void PXP_SetRotateConfig(PXP_Type *base, pxp_rotate_position_t position, pxp_rotate_degree_t degree, pxp_flip_mode_t flipMode)
Set the rotation configuration.
The PXP could rotate the process surface or the output buffer. There are two PXP versions:
Version 1: Only has one rotate sub module, the output buffer and process surface share the same rotate sub module, which means the process surface and output buffer could not be rotate at the same time. When pass in kPXP_RotateOutputBuffer, the process surface could not use the rotate, Also when pass in kPXP_RotateProcessSurface, output buffer could not use the rotate.
Version 2: Has two seperate rotate sub modules, the output buffer and process surface could configure the rotation independently.
Upper layer could use the macro PXP_SHARE_ROTATE to check which version is. PXP_SHARE_ROTATE=1 means version 1.
Note
This function is different depends on the macro PXP_SHARE_ROTATE.
- Parameters:
base – PXP peripheral base address.
position – Rotate process surface or output buffer.
degree – Rotate degree.
flipMode – Flip mode.
-
void PXP_BuildRect(PXP_Type *base, pxp_output_pixel_format_t outFormat, uint32_t value, uint16_t width, uint16_t height, uint16_t pitch, uint32_t outAddr)
Build a solid rectangle of given pixel value.
- Parameters:
base – PXP peripheral base address.
outFormat – output pixel format.
value – The value of the pixel to be filled in the rectangle in ARGB8888 format.
width – width of the rectangle.
height – height of the rectangle.
pitch – output pitch in byte.
outAddr – address of the memory to store the rectangle.
-
void PXP_SetNextCommand(PXP_Type *base, void *commandAddr)
Set the next command.
The PXP supports a primitive ability to queue up one operation while the current operation is running. Workflow:
Prepare the PXP register values except STAT, CSCCOEFn, NEXT in the memory in the order they appear in the register map.
Call this function sets the new operation to PXP.
There are two methods to check whether the PXP has loaded the new operation. The first method is using PXP_IsNextCommandPending. If there is new operation not loaded by the PXP, this function returns true. The second method is checking the flag kPXP_CommandLoadFlag, if command loaded, this flag asserts. User could enable interrupt kPXP_CommandLoadInterruptEnable to get the loaded signal in interrupt way.
When command loaded by PXP, a new command could be set using this function.
uint32_t pxp_command1[48]; uint32_t pxp_command2[48]; pxp_command1[0] = ...; pxp_command1[1] = ...; ... pxp_command2[0] = ...; pxp_command2[1] = ...; ... while (PXP_IsNextCommandPending(PXP)) { } PXP_SetNextCommand(PXP, pxp_command1); while (PXP_IsNextCommandPending(PXP)) { } PXP_SetNextCommand(PXP, pxp_command2);
- Parameters:
base – PXP peripheral base address.
commandAddr – Address of the new command.
-
static inline bool PXP_IsNextCommandPending(PXP_Type *base)
Check whether the next command is pending.
- Parameters:
base – UART peripheral base address.
- Returns:
True is pending, false is not.
-
static inline void PXP_CancelNextCommand(PXP_Type *base)
Cancel command set by PXP_SetNextCommand.
- Parameters:
base – UART peripheral base address.
-
void PXP_SetCsc1Mode(PXP_Type *base, pxp_csc1_mode_t mode)
Set the CSC1 mode.
The CSC1 module receives scaled YUV/YCbCr444 pixels from the scale engine and converts the pixels to the RGB888 color space. It could only be used by process surface.
- Parameters:
base – PXP peripheral base address.
mode – The conversion mode.
-
static inline void PXP_EnableCsc1(PXP_Type *base, bool enable)
Enable or disable the CSC1.
- Parameters:
base – PXP peripheral base address.
enable – True to enable, false to disable.
-
void PXP_SetInternalRamData(PXP_Type *base, pxp_ram_t ram, uint32_t bytesNum, uint8_t *data, uint16_t memStartAddr)
Write data to the PXP internal memory.
- Parameters:
base – PXP peripheral base address.
ram – Which internal memory to write.
bytesNum – How many bytes to write.
data – Pointer to the data to write.
memStartAddr – The start address in the internal memory to write the data.
-
void PXP_SetDitherFinalLutData(PXP_Type *base, const pxp_dither_final_lut_data_t *data)
Set the dither final LUT data.
The dither final LUT is only applicble to dither engine 0. It takes the bits[7:4] of the output pixel and looks up and 8 bit value from the 16 value LUT to generate the final output pixel to the next process module.
- Parameters:
base – PXP peripheral base address.
data – Pointer to the LUT data to set.
-
static inline void PXP_SetDitherConfig(PXP_Type *base, const pxp_dither_config_t *config)
Set the configuration for the dither block.
If the pre-dither LUT, post-dither LUT or ordered dither is used, please call PXP_SetInternalRamData to set the LUT data to internal memory.
If the final LUT is used, please call PXP_SetDitherFinalLutData to set the LUT data.
Note
When using ordered dithering, please set the PXP process block size same with the ordered dithering matrix size using function PXP_SetProcessBlockSize.
- Parameters:
base – PXP peripheral base address.
config – Pointer to the configuration.
-
void PXP_EnableDither(PXP_Type *base, bool enable)
Enable or disable dither engine in the PXP process path.
After the initialize function PXP_Init, the dither engine is disabled and not use in the PXP processing path. This function enables the dither engine and routes the dither engine output to the output buffer. When the dither engine is enabled using this function, PXP_SetDitherConfig must be called to configure dither engine correctly, otherwise there is not output to the output buffer.
- Parameters:
base – PXP peripheral base address.
enable – Pass in true to enable, false to disable.
-
void PXP_SetPorterDuffConfig(PXP_Type *base, uint8_t num, const pxp_porter_duff_config_t *config)
Set the Porter Duff configuration for one of the alpha process engine.
- Parameters:
base – PXP peripheral base address.
num – instance number.
config – Pointer to the configuration.
-
status_t PXP_GetPorterDuffConfigExt(pxp_porter_duff_blend_mode_t mode, pxp_porter_duff_config_t *config, uint8_t dstGlobalAlphaMode, uint8_t dstAlphaMode, uint8_t dstColorMode, uint8_t srcGlobalAlphaMode, uint8_t srcAlphaMode, uint8_t srcColorMode, uint8_t dstGlobalAlpha, uint8_t srcGlobalAlpha)
Get the Porter Duff configuration.
The FactorMode are selected based on blend mode, the other values are set based on input parameters. These values could be modified after calling this function. This function is extened PXP_GetPorterDuffConfig.
- Parameters:
mode – The blend mode.
config – Pointer to the configuration.
dstGlobalAlphaMode – Destination layer (or PS, s0) global alpha mode, see pxp_porter_duff_global_alpha_mode
dstAlphaMode – Destination layer (or PS, s0) alpha mode, see pxp_porter_duff_alpha_mode.
dstColorMode – Destination layer (or PS, s0) color mode, see pxp_porter_duff_color_mode.
srcGlobalAlphaMode – Source layer (or AS, s1) global alpha mode, see pxp_porter_duff_global_alpha_mode
srcAlphaMode – Source layer (or AS, s1) alpha mode, see pxp_porter_duff_alpha_mode.
srcColorMode – Source layer (or AS, s1) color mode, see pxp_porter_duff_color_mode.
dstGlobalAlpha – Destination layer (or PS, s0) global alpha value, 0~255
srcGlobalAlpha – Source layer (or AS, s1) global alpha value, 0~255
- Return values:
kStatus_Success – Successfully get the configuratoin.
kStatus_InvalidArgument – The blend mode not supported.
-
static inline status_t PXP_GetPorterDuffConfig(pxp_porter_duff_blend_mode_t mode, pxp_porter_duff_config_t *config)
Get the Porter Duff configuration by blend mode.
The FactorMode are selected based on blend mode, the AlphaMode are set to kPXP_PorterDuffAlphaStraight, the ColorMode are set to kPXP_PorterDuffColorWithAlpha, the GlobalAlphaMode are set to kPXP_PorterDuffLocalAlpha. These values could be modified after calling this function.
- Parameters:
mode – The blend mode.
config – Pointer to the configuration.
- Return values:
kStatus_Success – Successfully get the configuratoin.
kStatus_InvalidArgument – The blend mode not supported.
-
FSL_PXP_DRIVER_VERSION
-
enum _pxp_interrupt_enable
PXP interrupts to enable.
Values:
-
enumerator kPXP_CompleteInterruptEnable
PXP process completed. bit 1
-
enumerator kPXP_CommandLoadInterruptEnable
Interrupt to show that the command set by PXP_SetNextCommand has been loaded. bit 2
-
enumerator kPXP_CompressDoneInterruptEnable
Compress done interrupt enable. bit 15
-
enumerator kPXP_InputFetchCh0InterruptEnable
Input fetch channel 0 completed. bit 16
-
enumerator kPXP_InputFetchCh1InterruptEnable
Input fetch channel 1 completed. bit 17
-
enumerator kPXP_InputStoreCh0InterruptEnable
Input store channel 0 completed. bit 18
-
enumerator kPXP_InputStoreCh1InterruptEnable
Input store channel 1 completed. bit 19
-
enumerator kPXP_DitherFetchCh0InterruptEnable
Dither fetch channel 0 completed. bit 20
-
enumerator kPXP_DitherFetchCh1InterruptEnable
Dither fetch channel 1 completed. bit 21
-
enumerator kPXP_DitherStoreCh0InterruptEnable
Dither store channle 0 completed. bit 22
-
enumerator kPXP_DitherStoreCh1InterruptEnable
Dither store channle 1 completed. bit 23
-
enumerator kPXP_WfeaStoreCh0InterruptEnable
WFE-A store channel 0 completed. bit 24
-
enumerator kPXP_WfeaStoreCh1InterruptEnable
WFE-A store channel 1 completed. bit 25
-
enumerator kPXP_WfebStoreCh0InterruptEnable
WFE-B store channel 0 completed. bit 26
-
enumerator kPXP_WfebStoreCh1InterruptEnable
WFE-B store channel 1 completed. bit 27
-
enumerator kPXP_InputStoreInterruptEnable
Input store completed. bit 28
-
enumerator kPXP_DitherStoreInterruptEnable
Dither store completed. bit 29
-
enumerator kPXP_WfeaStoreInterruptEnable
WFE-A store completed. bit 30
-
enumerator kPXP_WfebStoreInterruptEnable
WFE-B store completed. bit 31
-
enumerator kPXP_CompleteInterruptEnable
-
enum _pxp_flags
PXP status flags.
Note
These enumerations are meant to be OR’d together to form a bit mask.
Values:
-
enumerator kPXP_CompleteFlag
PXP process completed. bit 0
-
enumerator kPXP_Axi0WriteErrorFlag
PXP encountered an AXI write error and processing has been terminated. bit 1
-
enumerator kPXP_Axi0ReadErrorFlag
PXP encountered an AXI read error and processing has been terminated. bit 2
-
enumerator kPXP_CommandLoadFlag
The command set by PXP_SetNextCommand has been loaded, could set new command. bit 3
-
enumerator kPXP_CompressDoneFlag
Compress done. bit 15
-
enumerator kPXP_InputFetchCh0CompleteFlag
Input fetch channel 0 completed. bit 16
-
enumerator kPXP_InputFetchCh1CompleteFlag
Input fetch channel 1 completed. bit 17
-
enumerator kPXP_InputStoreCh0CompleteFlag
Input store channel 0 completed. bit 18
-
enumerator kPXP_InputStoreCh1CompleteFlag
Input store channel 1 completed. bit 19
-
enumerator kPXP_DitherFetchCh0CompleteFlag
Dither fetch channel 0 completed. bit 20
-
enumerator kPXP_DitherFetchCh1CompleteFlag
Dither fetch channel 1 completed. bit 21
-
enumerator kPXP_DitherStoreCh0CompleteFlag
Dither store channel 0 completed. bit 22
-
enumerator kPXP_DitherStoreCh1CompleteFlag
Dither store channel 1 completed. bit 23
-
enumerator kPXP_WfeaStoreCh0CompleteFlag
WFE-A store channel 0 completed. bit 24
-
enumerator kPXP_WfeaStoreCh1CompleteFlag
WFE-A store channel 1 completed. bit 25
-
enumerator kPXP_WfebStoreCh0CompleteFlag
WFE-B store channel 0 completed. bit 26
-
enumerator kPXP_WfebStoreCh1CompleteFlag
WFE-B store channel 1 completed. bit 27
-
enumerator kPXP_InputStoreCompleteFlag
Input store completed. bit 28
-
enumerator kPXP_DitherStoreCompleteFlag
Dither store completed. bit 29
-
enumerator kPXP_WfeaStoreCompleteFlag
WFE-A store completed. bit 30
-
enumerator kPXP_WfebStoreCompleteFlag
WFE-B store completed. bit 31
-
enumerator kPXP_CompleteFlag
-
enum _pxp_flip_mode
PXP output flip mode.
Values:
-
enumerator kPXP_FlipDisable
Flip disable.
-
enumerator kPXP_FlipHorizontal
Horizontal flip.
-
enumerator kPXP_FlipVertical
Vertical flip.
-
enumerator kPXP_FlipBoth
Flip both directions.
-
enumerator kPXP_FlipDisable
-
enum _pxp_rotate_position
PXP rotate mode.
Values:
-
enumerator kPXP_RotateOutputBuffer
Rotate the output buffer.
-
enumerator kPXP_RotateProcessSurface
Rotate the process surface. Cannot be used together with flip, scale, or decimation function.
-
enumerator kPXP_RotateOutputBuffer
-
enum _pxp_rotate_degree
PXP rotate degree.
Values:
-
enumerator kPXP_Rotate0
Clock wise rotate 0 deg.
-
enumerator kPXP_Rotate90
Clock wise rotate 90 deg.
-
enumerator kPXP_Rotate180
Clock wise rotate 180 deg.
-
enumerator kPXP_Rotate270
Clock wise rotate 270 deg.
-
enumerator kPXP_Rotate0
-
enum _pxp_interlaced_output_mode
PXP interlaced output mode.
Values:
-
enumerator kPXP_OutputProgressive
All data written in progressive format to output buffer 0.
-
enumerator kPXP_OutputField0
Only write field 0 data to output buffer 0.
-
enumerator kPXP_OutputField1
Only write field 1 data to output buffer 0.
-
enumerator kPXP_OutputInterlaced
Field 0 write to buffer 0, field 1 write to buffer 1.
-
enumerator kPXP_OutputProgressive
-
enum _pxp_output_pixel_format
PXP output buffer format.
Values:
-
enumerator kPXP_OutputPixelFormatARGB8888
32-bit pixels with alpha.
-
enumerator kPXP_OutputPixelFormatRGB888
32-bit pixels without alpha (unpacked 24-bit format)
-
enumerator kPXP_OutputPixelFormatRGB888P
24-bit pixels without alpha (packed 24-bit format)
-
enumerator kPXP_OutputPixelFormatARGB1555
16-bit pixels with alpha.
-
enumerator kPXP_OutputPixelFormatARGB4444
16-bit pixels with alpha.
-
enumerator kPXP_OutputPixelFormatRGB555
16-bit pixels without alpha.
-
enumerator kPXP_OutputPixelFormatRGB444
16-bit pixels without alpha.
-
enumerator kPXP_OutputPixelFormatRGB565
16-bit pixels without alpha.
-
enumerator kPXP_OutputPixelFormatYUV1P444
32-bit pixels (1-plane XYUV unpacked).
-
enumerator kPXP_OutputPixelFormatUYVY1P422
16-bit pixels (1-plane U0,Y0,V0,Y1 interleaved bytes)
-
enumerator kPXP_OutputPixelFormatVYUY1P422
16-bit pixels (1-plane V0,Y0,U0,Y1 interleaved bytes)
-
enumerator kPXP_OutputPixelFormatY8
8-bit monochrome pixels (1-plane Y luma output)
-
enumerator kPXP_OutputPixelFormatY4
4-bit monochrome pixels (1-plane Y luma, 4 bit truncation)
-
enumerator kPXP_OutputPixelFormatYUV2P422
16-bit pixels (2-plane UV interleaved bytes)
-
enumerator kPXP_OutputPixelFormatYUV2P420
16-bit pixels (2-plane UV)
-
enumerator kPXP_OutputPixelFormatYVU2P422
16-bit pixels (2-plane VU interleaved bytes)
-
enumerator kPXP_OutputPixelFormatYVU2P420
16-bit pixels (2-plane VU)
-
enumerator kPXP_OutputPixelFormatARGB8888
-
enum _pxp_ps_pixel_format
PXP process surface buffer pixel format.
Values:
-
enumerator kPXP_PsPixelFormatRGB888
32-bit pixels without alpha (unpacked 24-bit format)
-
enumerator kPXP_PsPixelFormatRGB555
16-bit pixels without alpha.
-
enumerator kPXP_PsPixelFormatRGB444
16-bit pixels without alpha.
-
enumerator kPXP_PsPixelFormatRGB565
16-bit pixels without alpha.
-
enumerator kPXP_PsPixelFormatYUV1P444
32-bit pixels (1-plane XYUV unpacked).
-
enumerator kPXP_PsPixelFormatUYVY1P422
16-bit pixels (1-plane U0,Y0,V0,Y1 interleaved bytes)
-
enumerator kPXP_PsPixelFormatVYUY1P422
16-bit pixels (1-plane V0,Y0,U0,Y1 interleaved bytes)
-
enumerator kPXP_PsPixelFormatY8
8-bit monochrome pixels (1-plane Y luma output)
-
enumerator kPXP_PsPixelFormatY4
4-bit monochrome pixels (1-plane Y luma, 4 bit truncation)
-
enumerator kPXP_PsPixelFormatYUV2P422
16-bit pixels (2-plane UV interleaved bytes)
-
enumerator kPXP_PsPixelFormatYUV2P420
16-bit pixels (2-plane UV)
-
enumerator kPXP_PsPixelFormatYVU2P422
16-bit pixels (2-plane VU interleaved bytes)
-
enumerator kPXP_PsPixelFormatYVU2P420
16-bit pixels (2-plane VU)
-
enumerator kPXP_PsPixelFormatYVU422
16-bit pixels (3-plane)
-
enumerator kPXP_PsPixelFormatYVU420
16-bit pixels (3-plane)
-
enumerator kPXP_PsPixelFormatRGB888
-
enum _pxp_ps_yuv_format
PXP process surface buffer YUV format.
Values:
-
enumerator kPXP_PsYUVFormatYUV
YUV format.
-
enumerator kPXP_PsYUVFormatYCbCr
YCbCr format.
-
enumerator kPXP_PsYUVFormatYUV
-
enum _pxp_as_pixel_format
PXP alpha surface buffer pixel format.
Values:
-
enumerator kPXP_AsPixelFormatARGB8888
32-bit pixels with alpha.
-
enumerator kPXP_AsPixelFormatRGB888
32-bit pixels without alpha (unpacked 24-bit format)
-
enumerator kPXP_AsPixelFormatARGB1555
16-bit pixels with alpha.
-
enumerator kPXP_AsPixelFormatARGB4444
16-bit pixels with alpha.
-
enumerator kPXP_AsPixelFormatRGB555
16-bit pixels without alpha.
-
enumerator kPXP_AsPixelFormatRGB444
16-bit pixels without alpha.
-
enumerator kPXP_AsPixelFormatRGB565
16-bit pixels without alpha.
-
enumerator kPXP_AsPixelFormatARGB8888
-
enum _pxp_alpha_mode
PXP alpha mode during blending.
Values:
-
enumerator kPXP_AlphaEmbedded
The alpha surface pixel alpha value will be used for blend.
-
enumerator kPXP_AlphaOverride
The user defined alpha value will be used for blend directly.
-
enumerator kPXP_AlphaMultiply
The alpha surface pixel alpha value scaled the user defined alpha value will be used for blend, for example, pixel alpha set set to 200, user defined alpha set to 100, then the reault alpha is 200 * 100 / 255.
-
enumerator kPXP_AlphaRop
Raster operation.
-
enumerator kPXP_AlphaEmbedded
-
enum _pxp_rop_mode
PXP ROP mode during blending.
Explanation:
AS: Alpha surface
PS: Process surface
nAS: Alpha surface NOT value
nPS: Process surface NOT value
Values:
-
enumerator kPXP_RopMaskAs
AS AND PS.
-
enumerator kPXP_RopMaskNotAs
nAS AND PS.
-
enumerator kPXP_RopMaskAsNot
AS AND nPS.
-
enumerator kPXP_RopMergeAs
AS OR PS.
-
enumerator kPXP_RopMergeNotAs
nAS OR PS.
-
enumerator kPXP_RopMergeAsNot
AS OR nPS.
-
enumerator kPXP_RopNotCopyAs
nAS.
-
enumerator kPXP_RopNot
nPS.
-
enumerator kPXP_RopNotMaskAs
AS NAND PS.
-
enumerator kPXP_RopNotMergeAs
AS NOR PS.
-
enumerator kPXP_RopXorAs
AS XOR PS.
-
enumerator kPXP_RopNotXorAs
AS XNOR PS.
-
enum _pxp_block_size
PXP process block size.
Values:
-
enumerator kPXP_BlockSize8
Process 8x8 pixel blocks.
-
enumerator kPXP_BlockSize16
Process 16x16 pixel blocks.
-
enumerator kPXP_BlockSize8
-
enum _pxp_csc1_mode
PXP CSC1 mode.
Values:
-
enumerator kPXP_Csc1YUV2RGB
YUV to RGB.
-
enumerator kPXP_Csc1YCbCr2RGB
YCbCr to RGB.
-
enumerator kPXP_Csc1YUV2RGB
-
enum _pxp_csc2_mode
PXP CSC2 mode.
Values:
-
enumerator kPXP_Csc2YUV2RGB
YUV to RGB.
-
enumerator kPXP_Csc2YCbCr2RGB
YCbCr to RGB.
-
enumerator kPXP_Csc2RGB2YUV
RGB to YUV.
-
enumerator kPXP_Csc2RGB2YCbCr
RGB to YCbCr.
-
enumerator kPXP_Csc2YUV2RGB
-
enum _pxp_ram
PXP internal memory.
Values:
-
enumerator kPXP_RamDither0Lut
Dither 0 LUT memory.
-
enumerator kPXP_RamDither1Lut
Dither 1 LUT memory.
-
enumerator kPXP_RamDither2Lut
Dither 2 LUT memory.
-
enumerator kPXP_RamDither0Err0
Dither 0 ERR0 memory.
-
enumerator kPXP_RamDither0Err1
Dither 0 ERR1 memory.
-
enumerator kPXP_RamAluA
ALU A instr memory.
-
enumerator kPXP_RamAluB
ALU B instr memory.
-
enumerator kPXP_WfeAFetch
WFE-A fetch memory.
-
enumerator kPXP_WfeBFetch
WFE-B fetch memory.
-
enumerator kPXP_RamDither0Lut
-
enum _pxp_dither_mode
PXP dither mode.
Values:
-
enumerator kPXP_DitherPassThrough
Pass through, no dither.
-
enumerator kPXP_DitherFloydSteinberg
Floyd-Steinberg. For dither engine 0 only.
-
enumerator kPXP_DitherAtkinson
Atkinson. For dither engine 0 only.
-
enumerator kPXP_DitherOrdered
Ordered dither.
-
enumerator kPXP_DitherQuantOnly
No dithering, only quantization.
-
enumerator kPXP_DitherSierra
Sierra. For dither engine 0 only.
-
enumerator kPXP_DitherPassThrough
-
enum _pxp_dither_lut_mode
PXP dither LUT mode.
Values:
-
enumerator kPXP_DitherLutOff
The LUT memory is not used for LUT, could be used as ordered dither index matrix.
-
enumerator kPXP_DitherLutPreDither
Use LUT at the pre-dither stage, The pre-dither LUT could only be used in Floyd mode or Atkinson mode, which are not supported by current PXP module.
-
enumerator kPXP_DitherLutPostDither
Use LUT at the post-dither stage.
-
enumerator kPXP_DitherLutOff
-
enum _pxp_dither_matrix_size
PXP dither matrix size.
Values:
-
enumerator kPXP_DitherMatrix4
The dither index matrix is 4x4.
-
enumerator kPXP_DitherMatrix8
The dither index matrix is 8x8.
-
enumerator kPXP_DitherMatrix16
The dither index matrix is 16x16.
-
enumerator kPXP_DitherMatrix4
Porter Duff factor mode. .
Values:
-
enumerator kPXP_PorterDuffFactorOne
Use 1.
-
enumerator kPXP_PorterDuffFactorZero
Use 0.
-
enumerator kPXP_PorterDuffFactorStraight
Use straight alpha.
-
enumerator kPXP_PorterDuffFactorInversed
Use inversed alpha.
-
enumerator kPXP_PorterDuffFactorOne
Porter Duff global alpha mode. .
Values:
-
enumerator kPXP_PorterDuffGlobalAlpha
Use global alpha.
-
enumerator kPXP_PorterDuffLocalAlpha
Use local alpha in each pixel.
-
enumerator kPXP_PorterDuffScaledAlpha
Use global alpha * local alpha.
-
enumerator kPXP_PorterDuffGlobalAlpha
Porter Duff alpha mode. .
Values:
-
enumerator kPXP_PorterDuffAlphaStraight
Use straight alpha, s0_alpha’ = s0_alpha.
-
enumerator kPXP_PorterDuffAlphaInversed
Use inversed alpha, s0_alpha’ = 0xFF - s0_alpha.
-
enumerator kPXP_PorterDuffAlphaStraight
Porter Duff color mode. .
Values:
-
enumerator kPXP_PorterDuffColorStraight
- Deprecated:
Use kPXP_PorterDuffColorNoAlpha.
-
enumerator kPXP_PorterDuffColorInversed
- Deprecated:
Use kPXP_PorterDuffColorWithAlpha.
-
enumerator kPXP_PorterDuffColorNoAlpha
s0_pixel’ = s0_pixel.
-
enumerator kPXP_PorterDuffColorWithAlpha
s0_pixel’ = s0_pixel * s0_alpha”.
-
enumerator kPXP_PorterDuffColorStraight
-
enum _pxp_porter_duff_blend_mode
PXP Porter Duff blend mode. Note: don’t change the enum item value.
Values:
-
enumerator kPXP_PorterDuffSrc
Source Only
-
enumerator kPXP_PorterDuffAtop
Source Atop
-
enumerator kPXP_PorterDuffOver
Source Over
-
enumerator kPXP_PorterDuffIn
Source In.
-
enumerator kPXP_PorterDuffOut
Source Out.
-
enumerator kPXP_PorterDuffDst
Destination Only.
-
enumerator kPXP_PorterDuffDstAtop
Destination Atop.
-
enumerator kPXP_PorterDuffDstOver
Destination Over.
-
enumerator kPXP_PorterDuffDstIn
Destination In.
-
enumerator kPXP_PorterDuffDstOut
Destination Out.
-
enumerator kPXP_PorterDuffXor
XOR.
-
enumerator kPXP_PorterDuffClear
Clear.
-
enumerator kPXP_PorterDuffMax
-
enumerator kPXP_PorterDuffSrc
-
enum _pxp_process_engine_name
PXP process engine enumeration.
Values:
-
enumerator kPXP_PsAsOutEngine
-
enumerator kPXP_DitherEngine
-
enumerator kPXP_WfeaEngine
-
enumerator kPXP_WfebEngine
-
enumerator kPXP_InputFetchStoreEngine
-
enumerator kPXP_Alpha1Engine
-
enumerator kPXP_Csc2Engine
-
enumerator kPXP_LutEngine
-
enumerator kPXP_Rotate0Engine
-
enumerator kPXP_Rotate1Engine
-
enumerator kPXP_PsAsOutEngine
-
enum _pxp_fetch_engine_name
PXP fetch engine enumeration.
There are actually 4 fetch engine implemented, the others are WFE-A fetch engine and WFE-B fetch engine, whose registers are reserved from developer.
Values:
-
enumerator kPXP_FetchInput
-
enumerator kPXP_FetchDither
-
enumerator kPXP_FetchInput
-
enum _pxp_fetch_interface_mode
PXP fetch engine interface mode with the upstream store engine.
Values:
-
enumerator kPXP_FetchModeNormal
-
enumerator kPXP_FetchModeHandshake
-
enumerator kPXP_FetchModeBypass
-
enumerator kPXP_FetchModeNormal
-
enum _pxp_scanline_burst
PXP fetch/store engine burst length for scanline mode.
Values:
-
enumerator kPXP_Scanline8bytes
-
enumerator kPXP_Scanline16bytes
-
enumerator kPXP_Scanline32bytes
-
enumerator kPXP_Scanline64bytes
-
enumerator kPXP_Scanline8bytes
-
enum _pxp_activeBits
PXP fetch/store engine input/output active bits configuration.
Since fetch engine is 64-bit input and 32-bit output per channel, need to configure both channels to use 64-bit input mode. And expand configuration will have no effect.
Values:
-
enumerator kPXP_Active8Bits
-
enumerator kPXP_Active16Bits
-
enumerator kPXP_Active32Bits
-
enumerator kPXP_Active64Bits
-
enumerator kPXP_Active8Bits
-
enum _pxp_fetch_output_word_order
PXP fetch engine output word order when using 2 channels for 64-bit mode.
Values:
-
enumerator kPXP_FetchOutputChannel1channel0
In 64bit mode, channel 1 output high byte.
-
enumerator kPXP_FetchOutputChannel0channel1
In 64bit mode, channel 0 output high byte.
-
enumerator kPXP_FetchOutputChannel1channel0
-
enum _pxp_fetch_pixel_format
PXP fetch engine input pixel format.
Values:
-
enumerator kPXP_FetchFormatRGB565
-
enumerator kPXP_FetchFormatRGB555
-
enumerator kPXP_FetchFormatARGB1555
-
enumerator kPXP_FetchFormatRGB444
-
enumerator kPXP_FetchFormatARGB4444
-
enumerator kPXP_FetchFormatYUYVorYVYU
-
enumerator kPXP_FetchFormatUYVYorVYUY
-
enumerator kPXP_FetchFormatYUV422_2P
-
enumerator kPXP_FetchFormatRGB565
-
enum _pxp_store_engine_name
PXP store engine enumeration.
There are actually 4 store engine implemented, the others are WFE-A store engine and WFE-B store engine, whose registers are reserved from developer.
Values:
-
enumerator kPXP_StoreInput
-
enumerator kPXP_StoreDither
-
enumerator kPXP_StoreInput
-
enum _pxp_store_interface_mode
PXP store engine interface mode with the downstream fetch engine.
Values:
-
enumerator kPXP_StoreModeBypass
Store engine output the input data, after the shift function directly to the downstream Fetch Engine.
-
enumerator kPXP_StoreModeNormal
Store engine stores the input data to memory.
-
enumerator kPXP_StoreModeHandshake
Downstream fetch engine fetch data per scanline from memory using buffer sharing with store engine.
-
enumerator kPXP_StoreModeDual
Store engine outputs data directly to downstream fetch engine(Bypass) but also storing it to memory at the same time.
-
enumerator kPXP_StoreModeBypass
-
enum _pxp_store_yuv_mode
PXP store engine YUV output mode.
Values:
-
enumerator kPXP_StoreYUVDisable
Do not output YUV pixel format.
-
enumerator kPXP_StoreYUVPlane1
Use channel to output YUV422_1p pixel format, need to use shift operation to make sure each pixel component in its proper position: 64-bits of pixel data format and each 32 bits as {Y0, U0, Y1, V0}.
-
enumerator kPXP_StoreYUVPlane2
Use channel to output YUV422_2p pixel format, need to use shift operation to make sure each pixel component in its proper position: channel 0 {Y0,Y1}, channel 1 {U0,V0}.
-
enumerator kPXP_StoreYUVDisable
-
enum _pxp_cfa_input_format
PXP pre-dither CFA engine input pixel format.
Values:
-
enumerator kPXP_CfaRGB888
-
enumerator kPXP_CfaRGB444
-
enumerator kPXP_CfaRGB888
-
enum _pxp_histogram_mask_condition
PXP histogram mask condition.
Values:
-
enumerator kPXP_HistogramMaskEqual
Value that equal to value0 will pass the mask operation.
-
enumerator kPXP_HistogramMaskNotequal
Value that not equal to value0 will pass the mask operation.
-
enumerator kPXP_HistogramMaskIn
Value that within the range of value0-value1 will pass the mask operation.
-
enumerator kPXP_HistogramMaskOut
Value that without the range of value0-value1 will pass the mask operation.
-
enumerator kPXP_HistogramMaskEqual
-
enum _pxp_histgram_flags
PXP Histogram operation result flags.
Values:
-
enumerator kPXP_Histogram2levelMatch
-
enumerator kPXP_Histogram4levelMatch
-
enumerator kPXP_Histogram8levelMatch
-
enumerator kPXP_Histogram16levelMatch
-
enumerator kPXP_Histogram32levelMatch
-
enumerator kPXP_Histogram2levelMatch
-
typedef enum _pxp_flip_mode pxp_flip_mode_t
PXP output flip mode.
-
typedef enum _pxp_rotate_position pxp_rotate_position_t
PXP rotate mode.
-
typedef enum _pxp_rotate_degree pxp_rotate_degree_t
PXP rotate degree.
-
typedef enum _pxp_interlaced_output_mode pxp_interlaced_output_mode_t
PXP interlaced output mode.
-
typedef enum _pxp_output_pixel_format pxp_output_pixel_format_t
PXP output buffer format.
-
typedef struct _pxp_output_buffer_config pxp_output_buffer_config_t
PXP output buffer configuration.
-
typedef enum _pxp_ps_pixel_format pxp_ps_pixel_format_t
PXP process surface buffer pixel format.
-
typedef enum _pxp_ps_yuv_format pxp_ps_yuv_format_t
PXP process surface buffer YUV format.
-
typedef struct _pxp_ps_buffer_config pxp_ps_buffer_config_t
PXP process surface buffer configuration.
-
typedef enum _pxp_as_pixel_format pxp_as_pixel_format_t
PXP alpha surface buffer pixel format.
-
typedef struct _pxp_as_buffer_config pxp_as_buffer_config_t
PXP alphs surface buffer configuration.
-
typedef enum _pxp_alpha_mode pxp_alpha_mode_t
PXP alpha mode during blending.
-
typedef enum _pxp_rop_mode pxp_rop_mode_t
PXP ROP mode during blending.
Explanation:
AS: Alpha surface
PS: Process surface
nAS: Alpha surface NOT value
nPS: Process surface NOT value
-
typedef struct _pxp_as_blend_config pxp_as_blend_config_t
PXP alpha surface blending configuration.
-
typedef struct _pxp_as_blend_secondary_config pxp_as_blend_secondary_config_t
PXP secondary alpha surface blending engine configuration.
-
typedef enum _pxp_block_size pxp_block_size_t
PXP process block size.
-
typedef enum _pxp_csc1_mode pxp_csc1_mode_t
PXP CSC1 mode.
-
typedef enum _pxp_csc2_mode pxp_csc2_mode_t
PXP CSC2 mode.
-
typedef struct _pxp_csc2_config pxp_csc2_config_t
PXP CSC2 configuration.
Converting from YUV/YCbCr color spaces to the RGB color space uses the following equation structure:
R = A1(Y+D1) + A2(U+D2) + A3(V+D3) G = B1(Y+D1) + B2(U+D2) + B3(V+D3) B = C1(Y+D1) + C2(U+D2) + C3(V+D3)
Converting from the RGB color space to YUV/YCbCr color spaces uses the following equation structure:
Y = A1*R + A2*G + A3*B + D1 U = B1*R + B2*G + B3*B + D2 V = C1*R + C2*G + C3*B + D3
-
typedef enum _pxp_ram pxp_ram_t
PXP internal memory.
-
typedef struct _pxp_dither_final_lut_data pxp_dither_final_lut_data_t
PXP dither final LUT data.
-
typedef struct _pxp_dither_config pxp_dither_config_t
PXP dither configuration.
-
typedef enum _pxp_porter_duff_blend_mode pxp_porter_duff_blend_mode_t
PXP Porter Duff blend mode. Note: don’t change the enum item value.
-
typedef struct _pxp_pic_copy_config pxp_pic_copy_config_t
PXP Porter Duff blend mode. Note: don’t change the enum item value.
-
typedef enum _pxp_process_engine_name pxp_process_engine_name_t
PXP process engine enumeration.
-
typedef enum _pxp_fetch_engine_name pxp_fetch_engine_name_t
PXP fetch engine enumeration.
There are actually 4 fetch engine implemented, the others are WFE-A fetch engine and WFE-B fetch engine, whose registers are reserved from developer.
-
typedef enum _pxp_fetch_interface_mode pxp_fetch_interface_mode_t
PXP fetch engine interface mode with the upstream store engine.
-
typedef enum _pxp_scanline_burst pxp_scanline_burst_t
PXP fetch/store engine burst length for scanline mode.
-
typedef struct _pxp_block_format_config pxp_block_config_t
PXP fetch engine block configuration.
-
typedef enum _pxp_activeBits pxp_active_bits_t
PXP fetch/store engine input/output active bits configuration.
Since fetch engine is 64-bit input and 32-bit output per channel, need to configure both channels to use 64-bit input mode. And expand configuration will have no effect.
-
typedef enum _pxp_fetch_output_word_order pxp_fetch_output_word_order_t
PXP fetch engine output word order when using 2 channels for 64-bit mode.
-
typedef struct _pxp_fetch_shift_component pxp_fetch_shift_component_t
PXP fetch engine shift component configuration.
Fetch engine can divded each word into 4 components and shift them.
-
typedef struct _pxp_fetch_shift_config pxp_fetch_shift_config_t
PXP fetch engine shift configuration.
Fetch engine can divded each word into 4 components and shift them. For example, to change YUV444 to YVU444, U and V positions need to be shifted: OFFSET0=8, OFFSET1=0, OFFSET2=16, OFFSET3=24, WIDTH0/1/2/3=8
-
typedef enum _pxp_fetch_pixel_format pxp_fetch_pixel_format_t
PXP fetch engine input pixel format.
-
typedef struct _pxp_fetch_engine_config pxp_fetch_engine_config_t
PXP fetch engine configuration for one of the channel.
-
typedef enum _pxp_store_engine_name pxp_store_engine_name_t
PXP store engine enumeration.
There are actually 4 store engine implemented, the others are WFE-A store engine and WFE-B store engine, whose registers are reserved from developer.
-
typedef enum _pxp_store_interface_mode pxp_store_interface_mode_t
PXP store engine interface mode with the downstream fetch engine.
-
typedef enum _pxp_store_yuv_mode pxp_store_yuv_mode_t
PXP store engine YUV output mode.
-
typedef struct _pxp_store_shift_config pxp_store_shift_config_t
Shift configuration for PXP store engine.
-
typedef struct _pxp_store_engine_config pxp_store_engine_config_t
PXP store engine configuration for one of the channel.
-
typedef enum _pxp_cfa_input_format pxp_cfa_input_format_t
PXP pre-dither CFA engine input pixel format.
-
typedef struct _pxp_cfa_config pxp_cfa_config_t
PXP pre-dither CFA engine configuration.
-
typedef enum _pxp_histogram_mask_condition pxp_histogram_mask_condition_t
PXP histogram mask condition.
-
typedef struct _pxp_histogram_config pxp_histogram_config_t
PXP Histogram configuration.
-
typedef struct _pxp_histogram_mask_result pxp_histogram_mask_result_t
PXP Histogram mask result.
-
typedef struct _pxp_wfea_engine_config pxp_wfea_engine_config_t
PXP WFE-A engine configuration.
-
PXP_LUT_TABLE_BYTE
-
PXP_INTERNAL_RAM_LUT_BYTE
-
PXP_SHARE_ROTATE
-
PXP_USE_PATH
-
PXP_COMBINE_BYTE_TO_WORD(dataAddr)
-
struct _pxp_output_buffer_config
- #include <fsl_pxp.h>
PXP output buffer configuration.
Public Members
-
pxp_output_pixel_format_t pixelFormat
Output buffer pixel format.
-
pxp_interlaced_output_mode_t interlacedMode
Interlaced output mode.
-
uint32_t buffer0Addr
Output buffer 0 address.
-
uint32_t buffer1Addr
Output buffer 1 address, used for UV data in YUV 2-plane mode, or field 1 in output interlaced mode.
-
uint16_t pitchBytes
Number of bytes between two vertically adjacent pixels.
-
uint16_t width
Pixels per line.
-
uint16_t height
How many lines in output buffer.
-
pxp_output_pixel_format_t pixelFormat
-
struct _pxp_ps_buffer_config
- #include <fsl_pxp.h>
PXP process surface buffer configuration.
Public Members
-
pxp_ps_pixel_format_t pixelFormat
PS buffer pixel format.
-
bool swapByte
For each 16 bit word, set true to swap the two bytes.
-
uint32_t bufferAddr
Input buffer address for the first panel.
-
uint32_t bufferAddrU
Input buffer address for the second panel.
-
uint32_t bufferAddrV
Input buffer address for the third panel.
-
uint16_t pitchBytes
Number of bytes between two vertically adjacent pixels.
-
pxp_ps_pixel_format_t pixelFormat
-
struct _pxp_as_buffer_config
- #include <fsl_pxp.h>
PXP alphs surface buffer configuration.
Public Members
-
pxp_as_pixel_format_t pixelFormat
AS buffer pixel format.
-
uint32_t bufferAddr
Input buffer address.
-
uint16_t pitchBytes
Number of bytes between two vertically adjacent pixels.
-
pxp_as_pixel_format_t pixelFormat
-
struct _pxp_as_blend_config
- #include <fsl_pxp.h>
PXP alpha surface blending configuration.
Public Members
-
uint8_t alpha
User defined alpha value, only used when alphaMode is kPXP_AlphaOverride or kPXP_AlphaRop.
-
bool invertAlpha
Set true to invert the alpha.
-
pxp_alpha_mode_t alphaMode
Alpha mode.
-
pxp_rop_mode_t ropMode
ROP mode, only valid when alphaMode is kPXP_AlphaRop.
-
uint8_t alpha
-
struct _pxp_as_blend_secondary_config
- #include <fsl_pxp.h>
PXP secondary alpha surface blending engine configuration.
Public Members
-
bool invertAlpha
Set true to invert the alpha.
-
bool ropEnable
Enable rop mode.
-
pxp_rop_mode_t ropMode
ROP mode, only valid when ropEnable is true.
-
bool invertAlpha
-
struct _pxp_csc2_config
- #include <fsl_pxp.h>
PXP CSC2 configuration.
Converting from YUV/YCbCr color spaces to the RGB color space uses the following equation structure:
R = A1(Y+D1) + A2(U+D2) + A3(V+D3) G = B1(Y+D1) + B2(U+D2) + B3(V+D3) B = C1(Y+D1) + C2(U+D2) + C3(V+D3)
Converting from the RGB color space to YUV/YCbCr color spaces uses the following equation structure:
Y = A1*R + A2*G + A3*B + D1 U = B1*R + B2*G + B3*B + D2 V = C1*R + C2*G + C3*B + D3
Public Members
-
pxp_csc2_mode_t mode
Convertion mode.
-
float A1
A1.
-
float A2
A2.
-
float A3
A3.
-
float B1
B1.
-
float B2
B2.
-
float B3
B3.
-
float C1
C1.
-
float C2
C2.
-
float C3
C3.
-
int16_t D1
D1.
-
int16_t D2
D2.
-
int16_t D3
D3.
-
pxp_csc2_mode_t mode
-
struct _pxp_dither_final_lut_data
- #include <fsl_pxp.h>
PXP dither final LUT data.
Public Members
-
uint32_t data_3_0
Data 3 to data 0. Data 0 is the least significant byte.
-
uint32_t data_7_4
Data 7 to data 4. Data 4 is the least significant byte.
-
uint32_t data_11_8
Data 11 to data 8. Data 8 is the least significant byte.
-
uint32_t data_15_12
Data 15 to data 12. Data 12 is the least significant byte.
-
uint32_t data_3_0
-
struct _pxp_dither_config
- #include <fsl_pxp.h>
PXP dither configuration.
Public Members
-
uint32_t enableDither0
Enable dither engine 0 or not, set 1 to enable, 0 to disable.
-
uint32_t enableDither1
Enable dither engine 1 or not, set 1 to enable, 0 to disable.
-
uint32_t enableDither2
Enable dither engine 2 or not, set 1 to enable, 0 to disable.
-
uint32_t ditherMode0
Dither mode for dither engine 0. See _pxp_dither_mode.
-
uint32_t ditherMode1
Dither mode for dither engine 1. See _pxp_dither_mode.
-
uint32_t ditherMode2
Dither mode for dither engine 2. See _pxp_dither_mode.
-
uint32_t quantBitNum
Number of bits quantize down to, the valid value is 1~7.
-
uint32_t lutMode
How to use the memory LUT, see _pxp_dither_lut_mode. This must be set to kPXP_DitherLutOff if any dither engine uses kPXP_DitherOrdered mode.
-
uint32_t idxMatrixSize0
Size of index matrix used for dither for dither engine 0, see _pxp_dither_matrix_size.
-
uint32_t idxMatrixSize1
Size of index matrix used for dither for dither engine 1, see _pxp_dither_matrix_size.
-
uint32_t idxMatrixSize2
Size of index matrix used for dither for dither engine 2, see _pxp_dither_matrix_size.
-
uint32_t enableFinalLut
Enable the final LUT, set 1 to enable, 0 to disable.
-
uint32_t enableDither0
-
struct pxp_porter_duff_config_t
- #include <fsl_pxp.h>
PXP Porter Duff configuration.
Public Members
-
uint32_t enable
Enable or disable Porter Duff.
-
uint32_t srcFactorMode
Source layer (or AS, s1) factor mode, see pxp_porter_duff_factor_mode.
-
uint32_t dstGlobalAlphaMode
Destination layer (or PS, s0) global alpha mode, see pxp_porter_duff_global_alpha_mode.
-
uint32_t dstAlphaMode
Destination layer (or PS, s0) alpha mode, see pxp_porter_duff_alpha_mode.
-
uint32_t dstColorMode
Destination layer (or PS, s0) color mode, see pxp_porter_duff_color_mode.
-
uint32_t dstFactorMode
Destination layer (or PS, s0) factor mode, see pxp_porter_duff_factor_mode.
-
uint32_t srcGlobalAlphaMode
Source layer (or AS, s1) global alpha mode, see pxp_porter_duff_global_alpha_mode.
-
uint32_t srcAlphaMode
Source layer (or AS, s1) alpha mode, see pxp_porter_duff_alpha_mode.
-
uint32_t srcColorMode
Source layer (or AS, s1) color mode, see pxp_porter_duff_color_mode.
-
uint32_t dstGlobalAlpha
Destination layer (or PS, s0) global alpha value, 0~255.
-
uint32_t srcGlobalAlpha
Source layer (or AS, s1) global alpha value, 0~255.
-
uint32_t enable
-
struct _pxp_pic_copy_config
- #include <fsl_pxp.h>
PXP Porter Duff blend mode. Note: don’t change the enum item value.
Public Members
-
uint32_t srcPicBaseAddr
Source picture base address.
-
uint16_t srcPitchBytes
Pitch of the source buffer.
-
uint16_t srcOffsetX
Copy position in source picture.
-
uint16_t srcOffsetY
Copy position in source picture.
-
uint32_t destPicBaseAddr
Destination picture base address.
-
uint16_t destPitchBytes
Pitch of the destination buffer.
-
uint16_t destOffsetX
Copy position in destination picture.
-
uint16_t destOffsetY
Copy position in destination picture.
-
uint16_t width
Pixel number each line to copy.
-
uint16_t height
Lines to copy.
-
pxp_as_pixel_format_t pixelFormat
Buffer pixel format.
-
uint32_t srcPicBaseAddr
-
struct _pxp_block_format_config
- #include <fsl_pxp.h>
PXP fetch engine block configuration.
Public Members
-
bool enableblock
Enable to use block mode instead of scanline mode. Note: 1.Make sure to enable if rotate or flip mode is enabled. 2.Block mode cannot work on 64bpp data stream where activeBits = 64. 3. If LUT processing is in the path between the fetch and store engind, block mode must be enabled.
-
bool blockSize16
Enable to use 16*16 block, otherwise it will be 8*8 block.
-
pxp_scanline_burst_t burstLength
When using scanline mode, configure this for burst length.
-
bool enableblock
-
struct _pxp_fetch_shift_component
- #include <fsl_pxp.h>
PXP fetch engine shift component configuration.
Fetch engine can divded each word into 4 components and shift them.
-
struct _pxp_fetch_shift_config
- #include <fsl_pxp.h>
PXP fetch engine shift configuration.
Fetch engine can divded each word into 4 components and shift them. For example, to change YUV444 to YVU444, U and V positions need to be shifted: OFFSET0=8, OFFSET1=0, OFFSET2=16, OFFSET3=24, WIDTH0/1/2/3=8
-
struct _pxp_fetch_engine_config
- #include <fsl_pxp.h>
PXP fetch engine configuration for one of the channel.
Public Members
-
bool channelEnable
Enable channel.
-
uint32_t inputBaseAddr0
The input base address. Used for Y plane input when pixel format is YUV422_2p.
-
uint32_t inputBaseAddr1
Must configure this for UV plane when input pixel format is YUV422_2p.
-
uint16_t totalHeight
Total height for the actual fetch size.
-
uint16_t totalWidth
Total width for the actual fetch size.
-
uint16_t pitchBytes
Channel input pitch
-
uint16_t ulcX
X coordinate of upper left coordinate in pixels of the active area of the total input memory
-
uint16_t ulcY
Y coordinate of upper left coordinate in pixels of the active area of the total input memory
-
uint16_t lrcX
X coordinate of Lower right coordinate in pixels of the active area of the total input memory
-
uint16_t lrcY
Y coordinate of Lower right coordinate in pixels of the active area of the total input memory
-
uint32_t backGroundColor
Pixel value of the background color for the space outside the active area.
-
pxp_fetch_interface_mode_t interface
Interface mode, normal/bypass/handshake
-
pxp_active_bits_t activeBits
Input active bits.
-
pxp_fetch_pixel_format_t pixelFormat
Input pixel fetch format
-
bool expandEnable
If enabled, input pixel will be expanded to ARGB8888, RGB888 or YUV444 of 32-bit format at the output.
-
pxp_flip_mode_t flipMode
Flip the fetched input.
-
pxp_rotate_degree_t rotateDegree
Rotate the fetched input.
-
pxp_block_config_t fetchFormat
Block mode configuration. Make sure to enable block if rotate or flip mode is enabled.
-
pxp_fetch_shift_config_t shiftConfig
Shift operation configuration.
-
pxp_fetch_output_word_order_t wordOrder
Output word order when using 2 channels for 64-bit mode.
-
bool channelEnable
-
struct _pxp_store_shift_config
- #include <fsl_pxp.h>
Shift configuration for PXP store engine.
Public Members
-
bool shiftBypass
Bypass the data shift
-
uint64_t *pDataShiftMask
Pointer to mask0~mask7 to mask the 64-bit of output data, data is masked first then shifted according to width.
-
uint8_t *pDataShiftWidth
Pointer to width0~width7. Bit 7 is for shifted direction, 0 to right. Bit0~5 is for shift width.
-
uint8_t *pFlagShiftMask
Pointer to mask0~mask7 to mask the 8-bit of output flag, flag is masked first then shifted according to width.
-
uint8_t *pFlagShiftWidth
Pointer to width0~width7. Bit 6 is for shifted direction, 0 to right. Bit0~5 is for shift width.
-
bool shiftBypass
-
struct _pxp_store_engine_config
- #include <fsl_pxp.h>
PXP store engine configuration for one of the channel.
Public Members
-
bool channelEnable
Enable channel.
-
uint32_t outputBaseAddr0
The channel 0 output address if using 2 channels. If using 1 channel(must be channel
0) and YUV422_2p output format, is for Y plane address.
-
uint32_t outputBaseAddr1
The channel 1 output address if using 2 channels. If using 1 channel(must be channel
0) and YUV422_2p output format, is for UV plane address.
-
uint16_t totalHeight
Total height for the actual store size.
-
uint16_t totalWidth
Total width for the actual store size.
-
uint16_t pitchBytes
Channel input pitch
-
pxp_store_interface_mode_t interface
Interface mode, normal/bypass/handshake/dual. Make sure 2 channels use the same mode if both enabled.
-
pxp_active_bits_t activeBits
Output active bits.
-
pxp_store_yuv_mode_t yuvMode
Whether to output YUV pixel format.
-
bool useFixedData
Whether to use fixed value for the output data. Can be used to write fixed value to specific memory location for memory initialization.
-
uint32_t fixedData
The value of the fixed data.
-
bool packInSelect
When enabled, channel 0 will select low 32 bit shift out data to pack while channel i select high 32 bit, otherwise all 64-bit of data will be selected.
-
pxp_block_config_t storeFormat
The format to store data, block or otherwise.
-
pxp_store_shift_config_t shiftConfig
Shift operation configuration.
-
bool channelEnable
-
struct _pxp_cfa_config
- #include <fsl_pxp.h>
PXP pre-dither CFA engine configuration.
Public Members
-
bool bypass
Bypass the CFA process
-
pxp_cfa_input_format_t pixelInFormat
The pixel input format for CFA.
-
uint8_t arrayWidth
CFA array vertical size in pixels, min 3 max 15.
-
uint8_t arrayHeight
CFA array horizontal size in pixels, min 3 max 15.
-
uint16_t totalHeight
Total height for the buffer size, make sure it is aligned with the dither fetch engine and dither engine.
-
uint16_t totalWidth
Total width for the buffer size, make sure it is aligned with the dither fetch engine and dither engine.
-
uint32_t *cfaValue
Pointer to the value for the CFA array. 2-bit per component: 00-R,01-G,10-B,11-W. For a 4x4 array, 32 bits are need.
-
bool bypass
-
struct _pxp_histogram_config
- #include <fsl_pxp.h>
PXP Histogram configuration.
Public Members
-
bool enable
Enable histogram process.
-
uint8_t *pParamValue
Pointer to the 62(2+4+8+16+32) byte of param value for 2-level, 4-level…..32-level parameters. Only low 5-bit of each byte is valid.
-
uint8_t lutValueOffset
The starting bit position of the LUT value.
-
uint8_t lutValueWidth
The bit width of the LUT value, should be no more than 6 bits since only 63 LUTs are supported.
-
bool enableMask
Enable mask operation.
-
uint8_t maskValue0
Value 0 for the condition judgement.
-
uint8_t maskValue1
Value 1 for the condition judgement.
-
uint8_t maskOffset
The starting bit position of the field to be checked against mask condition.
-
uint8_t maskWidth
The width of the field to be checked against mask condition.
-
pxp_histogram_mask_condition_t condition
The mask condition.
-
uint16_t totalHeight
Total height for the buffer size, make sure it is aligned with the output of legacy flow or the WFE-A/B engine.
-
uint16_t totalWidth
Total width for the buffer size, make sure it is aligned with the output of legacy flow or the WFE-A/B engine.
-
bool enable
-
struct _pxp_histogram_mask_result
- #include <fsl_pxp.h>
PXP Histogram mask result.
Public Members
-
uint32_t pixelCount
The total count of the pixels that pass the mask(collided pixels).
-
uint32_t minX
The x offset of the ULC of the minimal histogram that covers all passed pixels.
-
uint32_t minY
The y offset of the ULC of the minimal histogram that covers all passed pixels.
-
uint32_t maxX
The x offset of the LRC of the minimal histogram that covers all passed pixels.
-
uint32_t maxY
The y offset of the LRC of the minimal histogram that covers all passed pixels.
-
uint64_t lutlist
The 64-bit LUT list of collided pixels, if pixel of LUT17 is collided, bit17 in the list is set.
-
uint32_t pixelCount
-
struct _pxp_wfea_engine_config
- #include <fsl_pxp.h>
PXP WFE-A engine configuration.
Public Members
-
uint32_t y4Addr
Address for Y4 buffer.
-
uint32_t y4cAddr
Address for Y4C buffer, {Y4[3:0],3’b000,collision}, 8bpp.
-
uint32_t wbAddr
Address for EPDC working buffer.
-
uint16_t updateWidth
Width of the update area.
-
uint16_t updateHeight
Height of the update area.
-
uint16_t updatePitch
Pitch of the update area.
-
uint16_t ulcX
X coordinate of upper left coordinate of the total input memory
-
uint16_t ulcY
Y coordinate of upper left coordinate of the total input memory
-
uint16_t resX
Horizontal resolution in pixels.
-
uint8_t lutNum
The EPDC LUT number for the update.
-
bool fullUpdateEnable
Enable full update.
-
bool alphaEnable
Enable alpha field, upd is {Y4[3:0],3’b000,alpha} format, otherwise its {Y4[3:0],4’b0000}.
-
bool detectionOnly
Detection only, do not write working buffer.
-
uint32_t y4Addr
QTMR: Quad Timer Driver
-
void QTMR_Init(TMR_Type *base, qtmr_channel_selection_t channel, const qtmr_config_t *config)
Ungates the Quad Timer clock and configures the peripheral for basic operation.
Note
This API should be called at the beginning of the application using the Quad Timer driver.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
config – Pointer to user’s Quad Timer config structure
-
void QTMR_Deinit(TMR_Type *base, qtmr_channel_selection_t channel)
Stops the counter and gates the Quad Timer clock.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
-
void QTMR_GetDefaultConfig(qtmr_config_t *config)
Fill in the Quad Timer config struct with the default settings.
The default values are:
config->debugMode = kQTMR_RunNormalInDebug; config->enableExternalForce = false; config->enableMasterMode = false; config->faultFilterCount = 0; config->faultFilterPeriod = 0; config->primarySource = kQTMR_ClockDivide_2; config->secondarySource = kQTMR_Counter0InputPin;
- Parameters:
config – Pointer to user’s Quad Timer config structure.
-
void QTMR_EnableInterrupts(TMR_Type *base, qtmr_channel_selection_t channel, uint32_t mask)
Enables the selected Quad Timer interrupts.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
mask – The interrupts to enable. This is a logical OR of members of the enumeration qtmr_interrupt_enable_t
-
void QTMR_DisableInterrupts(TMR_Type *base, qtmr_channel_selection_t channel, uint32_t mask)
Disables the selected Quad Timer interrupts.
- Parameters:
base – Quad Timer peripheral base addres
channel – Quad Timer channel number
mask – The interrupts to enable. This is a logical OR of members of the enumeration qtmr_interrupt_enable_t
-
uint32_t QTMR_GetEnabledInterrupts(TMR_Type *base, qtmr_channel_selection_t channel)
Gets the enabled Quad Timer interrupts.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
- Returns:
The enabled interrupts. This is the logical OR of members of the enumeration qtmr_interrupt_enable_t
-
uint32_t QTMR_GetStatus(TMR_Type *base, qtmr_channel_selection_t channel)
Gets the Quad Timer status flags.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
- Returns:
The status flags. This is the logical OR of members of the enumeration qtmr_status_flags_t
-
void QTMR_ClearStatusFlags(TMR_Type *base, qtmr_channel_selection_t channel, uint32_t mask)
Clears the Quad Timer status flags.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
mask – The status flags to clear. This is a logical OR of members of the enumeration qtmr_status_flags_t
-
void QTMR_SetTimerPeriod(TMR_Type *base, qtmr_channel_selection_t channel, uint16_t ticks)
Sets the timer period in ticks.
Timers counts from initial value till it equals the count value set here. The counter will then reinitialize to the value specified in the Load register.
Note
This function will write the time period in ticks to COMP1 or COMP2 register depending on the count direction
User can call the utility macros provided in fsl_common.h to convert to ticks
This function supports cases, providing only primary source clock without secondary source clock.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
ticks – Timer period in units of ticks
-
void QTMR_SetCompareValue(TMR_Type *base, qtmr_channel_selection_t channel, uint16_t ticks)
Set compare value.
This function sets the value used for comparison with the counter value.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
ticks – Timer period in units of ticks.
-
static inline void QTMR_SetLoadValue(TMR_Type *base, qtmr_channel_selection_t channel, uint16_t value)
Set load value.
This function sets the value used to initialize the counter after a counter comparison.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
value – Load register initialization value.
-
static inline uint16_t QTMR_GetCurrentTimerCount(TMR_Type *base, qtmr_channel_selection_t channel)
Reads the current timer counting value.
This function returns the real-time timer counting value, in a range from 0 to a timer period.
Note
User can call the utility macros provided in fsl_common.h to convert ticks to usec or msec
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
- Returns:
Current counter value in ticks
-
static inline void QTMR_StartTimer(TMR_Type *base, qtmr_channel_selection_t channel, qtmr_counting_mode_t clockSource)
Starts the Quad Timer counter.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
clockSource – Quad Timer clock source
-
static inline void QTMR_StopTimer(TMR_Type *base, qtmr_channel_selection_t channel)
Stops the Quad Timer counter.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
-
void QTMR_EnableDma(TMR_Type *base, qtmr_channel_selection_t channel, uint32_t mask)
Enable the Quad Timer DMA.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
mask – The DMA to enable. This is a logical OR of members of the enumeration qtmr_dma_enable_t
-
void QTMR_DisableDma(TMR_Type *base, qtmr_channel_selection_t channel, uint32_t mask)
Disable the Quad Timer DMA.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
mask – The DMA to enable. This is a logical OR of members of the enumeration qtmr_dma_enable_t
-
void QTMR_SetPwmOutputToIdle(TMR_Type *base, qtmr_channel_selection_t channel, bool idleStatus)
Set PWM output in idle status (high or low).
Note
When the PWM is set again, the counting needs to be restarted.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
idleStatus – True: PWM output is high in idle status; false: PWM output is low in idle status.
-
static inline qtmr_pwm_out_state_t QTMR_GetPwmOutputStatus(TMR_Type *base, qtmr_channel_selection_t channel)
Get the channel output status.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
- Returns:
Current channel output status.
-
uint8_t QTMR_GetPwmChannelStatus(TMR_Type *base, qtmr_channel_selection_t channel)
Get the PWM channel dutycycle value.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
- Returns:
Current channel dutycycle value.
-
void QTMR_SetPwmClockMode(TMR_Type *base, qtmr_channel_selection_t channel, qtmr_primary_count_source_t prescaler)
This function set the value of the prescaler on QTimer channels.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
prescaler – Set prescaler value
-
FSL_QTMR_DRIVER_VERSION
Version
-
enum _qtmr_primary_count_source
Quad Timer primary clock source selection.
Values:
-
enumerator kQTMR_ClockCounter0InputPin
Use counter 0 input pin
-
enumerator kQTMR_ClockCounter1InputPin
Use counter 1 input pin
-
enumerator kQTMR_ClockCounter2InputPin
Use counter 2 input pin
-
enumerator kQTMR_ClockCounter3InputPin
Use counter 3 input pin
-
enumerator kQTMR_ClockCounter0Output
Use counter 0 output
-
enumerator kQTMR_ClockCounter1Output
Use counter 1 output
-
enumerator kQTMR_ClockCounter2Output
Use counter 2 output
-
enumerator kQTMR_ClockCounter3Output
Use counter 3 output
-
enumerator kQTMR_ClockDivide_1
IP bus clock divide by 1 prescaler
-
enumerator kQTMR_ClockDivide_2
IP bus clock divide by 2 prescaler
-
enumerator kQTMR_ClockDivide_4
IP bus clock divide by 4 prescaler
-
enumerator kQTMR_ClockDivide_8
IP bus clock divide by 8 prescaler
-
enumerator kQTMR_ClockDivide_16
IP bus clock divide by 16 prescaler
-
enumerator kQTMR_ClockDivide_32
IP bus clock divide by 32 prescaler
-
enumerator kQTMR_ClockDivide_64
IP bus clock divide by 64 prescaler
-
enumerator kQTMR_ClockDivide_128
IP bus clock divide by 128 prescaler
-
enumerator kQTMR_ClockCounter0InputPin
-
enum _qtmr_input_source
Quad Timer input sources selection.
Values:
-
enumerator kQTMR_Counter0InputPin
Use counter 0 input pin
-
enumerator kQTMR_Counter1InputPin
Use counter 1 input pin
-
enumerator kQTMR_Counter2InputPin
Use counter 2 input pin
-
enumerator kQTMR_Counter3InputPin
Use counter 3 input pin
-
enumerator kQTMR_Counter0InputPin
-
enum _qtmr_counting_mode
Quad Timer counting mode selection.
Values:
-
enumerator kQTMR_NoOperation
No operation
-
enumerator kQTMR_PriSrcRiseEdge
Count rising edges of primary source
-
enumerator kQTMR_PriSrcRiseAndFallEdge
Count rising and falling edges of primary source
-
enumerator kQTMR_PriSrcRiseEdgeSecInpHigh
Count rise edges of pri SRC while sec inp high active
-
enumerator kQTMR_QuadCountMode
Quadrature count mode, uses pri and sec sources
-
enumerator kQTMR_PriSrcRiseEdgeSecDir
Count rising edges of pri SRC; sec SRC specifies dir
-
enumerator kQTMR_SecSrcTrigPriCnt
Edge of sec SRC trigger primary count until compare
-
enumerator kQTMR_CascadeCount
Cascaded count mode (up/down)
-
enumerator kQTMR_NoOperation
-
enum _qtmr_pwm_out_state
Quad Timer PWM output state.
Values:
-
enumerator kQTMR_PwmLow
The output state of PWM channel is low
-
enumerator kQTMR_PwmHigh
The output state of PWM channel is low
-
enumerator kQTMR_PwmLow
-
enum _qtmr_output_mode
Quad Timer output mode selection.
Values:
-
enumerator kQTMR_AssertWhenCountActive
Assert OFLAG while counter is active
-
enumerator kQTMR_ClearOnCompare
Clear OFLAG on successful compare
-
enumerator kQTMR_SetOnCompare
Set OFLAG on successful compare
-
enumerator kQTMR_ToggleOnCompare
Toggle OFLAG on successful compare
-
enumerator kQTMR_ToggleOnAltCompareReg
Toggle OFLAG using alternating compare registers
-
enumerator kQTMR_SetOnCompareClearOnSecSrcInp
Set OFLAG on compare, clear on sec SRC input edge
-
enumerator kQTMR_SetOnCompareClearOnCountRoll
Set OFLAG on compare, clear on counter rollover
-
enumerator kQTMR_EnableGateClock
Enable gated clock output while count is active
-
enumerator kQTMR_AssertWhenCountActive
-
enum _qtmr_input_capture_edge
Quad Timer input capture edge mode, rising edge, or falling edge.
Values:
-
enumerator kQTMR_NoCapture
Capture is disabled
-
enumerator kQTMR_RisingEdge
Capture on rising edge (IPS=0) or falling edge (IPS=1)
-
enumerator kQTMR_FallingEdge
Capture on falling edge (IPS=0) or rising edge (IPS=1)
-
enumerator kQTMR_RisingAndFallingEdge
Capture on both edges
-
enumerator kQTMR_NoCapture
-
enum _qtmr_preload_control
Quad Timer input capture edge mode, rising edge, or falling edge.
Values:
-
enumerator kQTMR_NoPreload
Never preload
-
enumerator kQTMR_LoadOnComp1
Load upon successful compare with value in COMP1
-
enumerator kQTMR_LoadOnComp2
Load upon successful compare with value in COMP2
-
enumerator kQTMR_NoPreload
-
enum _qtmr_debug_action
List of Quad Timer run options when in Debug mode.
Values:
-
enumerator kQTMR_RunNormalInDebug
Continue with normal operation
-
enumerator kQTMR_HaltCounter
Halt counter
-
enumerator kQTMR_ForceOutToZero
Force output to logic 0
-
enumerator kQTMR_HaltCountForceOutZero
Halt counter and force output to logic 0
-
enumerator kQTMR_RunNormalInDebug
-
enum _qtmr_interrupt_enable
List of Quad Timer interrupts.
Values:
-
enumerator kQTMR_CompareInterruptEnable
Compare interrupt.
-
enumerator kQTMR_Compare1InterruptEnable
Compare 1 interrupt.
-
enumerator kQTMR_Compare2InterruptEnable
Compare 2 interrupt.
-
enumerator kQTMR_OverflowInterruptEnable
Timer overflow interrupt.
-
enumerator kQTMR_EdgeInterruptEnable
Input edge interrupt.
-
enumerator kQTMR_CompareInterruptEnable
-
enum _qtmr_status_flags
List of Quad Timer flags.
Values:
-
enumerator kQTMR_CompareFlag
Compare flag
-
enumerator kQTMR_Compare1Flag
Compare 1 flag
-
enumerator kQTMR_Compare2Flag
Compare 2 flag
-
enumerator kQTMR_OverflowFlag
Timer overflow flag
-
enumerator kQTMR_EdgeFlag
Input edge flag
-
enumerator kQTMR_CompareFlag
-
enum _qtmr_channel_selection
List of channel selection.
Values:
-
enumerator kQTMR_Channel_0
TMR Channel 0
-
enumerator kQTMR_Channel_1
TMR Channel 1
-
enumerator kQTMR_Channel_2
TMR Channel 2
-
enumerator kQTMR_Channel_3
TMR Channel 3
-
enumerator kQTMR_Channel_0
-
enum _qtmr_dma_enable
List of Quad Timer DMA enable.
Values:
-
enumerator kQTMR_InputEdgeFlagDmaEnable
Input Edge Flag DMA Enable.
-
enumerator kQTMR_ComparatorPreload1DmaEnable
Comparator Preload Register 1 DMA Enable.
-
enumerator kQTMR_ComparatorPreload2DmaEnable
Comparator Preload Register 2 DMA Enable.
-
enumerator kQTMR_InputEdgeFlagDmaEnable
-
typedef enum _qtmr_primary_count_source qtmr_primary_count_source_t
Quad Timer primary clock source selection.
-
typedef enum _qtmr_input_source qtmr_input_source_t
Quad Timer input sources selection.
-
typedef enum _qtmr_counting_mode qtmr_counting_mode_t
Quad Timer counting mode selection.
-
typedef enum _qtmr_pwm_out_state qtmr_pwm_out_state_t
Quad Timer PWM output state.
-
typedef enum _qtmr_output_mode qtmr_output_mode_t
Quad Timer output mode selection.
-
typedef enum _qtmr_input_capture_edge qtmr_input_capture_edge_t
Quad Timer input capture edge mode, rising edge, or falling edge.
-
typedef enum _qtmr_preload_control qtmr_preload_control_t
Quad Timer input capture edge mode, rising edge, or falling edge.
-
typedef enum _qtmr_debug_action qtmr_debug_action_t
List of Quad Timer run options when in Debug mode.
-
typedef enum _qtmr_interrupt_enable qtmr_interrupt_enable_t
List of Quad Timer interrupts.
-
typedef enum _qtmr_status_flags qtmr_status_flags_t
List of Quad Timer flags.
-
typedef enum _qtmr_channel_selection qtmr_channel_selection_t
List of channel selection.
-
typedef enum _qtmr_dma_enable qtmr_dma_enable_t
List of Quad Timer DMA enable.
-
typedef struct _qtmr_config qtmr_config_t
Quad Timer config structure.
This structure holds the configuration settings for the Quad Timer peripheral. To initialize this structure to reasonable defaults, call the QTMR_GetDefaultConfig() function and pass a pointer to your config structure instance.
The config struct can be made const so it resides in flash
-
status_t QTMR_SetupPwm(TMR_Type *base, qtmr_channel_selection_t channel, uint32_t pwmFreqHz, uint8_t dutyCyclePercent, bool outputPolarity, uint32_t srcClock_Hz)
Sets up Quad timer module for PWM signal output.
The function initializes the timer module according to the parameters passed in by the user. The function also sets up the value compare registers to match the PWM signal requirements.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
pwmFreqHz – PWM signal frequency in Hz
dutyCyclePercent – PWM pulse width, value should be between 0 to 100 0=inactive signal(0% duty cycle)… 100=active signal (100% duty cycle)
outputPolarity – true: invert polarity of the output signal, false: no inversion
srcClock_Hz – Main counter clock in Hz.
- Returns:
Returns an error if there was error setting up the signal.
-
void QTMR_SetupInputCapture(TMR_Type *base, qtmr_channel_selection_t channel, qtmr_input_source_t capturePin, bool inputPolarity, bool reloadOnCapture, qtmr_input_capture_edge_t captureMode)
Allows the user to count the source clock cycles until a capture event arrives.
The count is stored in the capture register.
- Parameters:
base – Quad Timer peripheral base address
channel – Quad Timer channel number
capturePin – Pin through which we receive the input signal to trigger the capture
inputPolarity – true: invert polarity of the input signal, false: no inversion
reloadOnCapture – true: reload the counter when an input capture occurs, false: no reload
captureMode – Specifies which edge of the input signal triggers a capture
-
TMR_CSCTRL_OFLAG_MASK
-
TMR_CSCTRL_OFLAG_SHIFT
-
struct _qtmr_config
- #include <fsl_qtmr.h>
Quad Timer config structure.
This structure holds the configuration settings for the Quad Timer peripheral. To initialize this structure to reasonable defaults, call the QTMR_GetDefaultConfig() function and pass a pointer to your config structure instance.
The config struct can be made const so it resides in flash
Public Members
-
qtmr_primary_count_source_t primarySource
Specify the primary count source
-
qtmr_input_source_t secondarySource
Specify the secondary count source
-
bool enableMasterMode
true: Broadcast compare function output to other counters; false no broadcast
-
bool enableExternalForce
true: Compare from another counter force state of OFLAG signal false: OFLAG controlled by local counter
-
uint8_t faultFilterCount
Fault filter count
-
uint8_t faultFilterPeriod
Fault filter period;value of 0 will bypass the filter
-
qtmr_debug_action_t debugMode
Operation in Debug mode
-
qtmr_primary_count_source_t primarySource
Romapi
Flash Pad Definitions.
Values:
-
enumerator kSerialFlash_1Pad
-
enumerator kSerialFlash_2Pads
-
enumerator kSerialFlash_4Pads
-
enumerator kSerialFlash_8Pads
-
enumerator kSerialFlash_1Pad
FLEXSPI clock configuration type.
Values:
-
enumerator kFLEXSPIClk_SDR
Clock configure for SDR mode
-
enumerator kFLEXSPIClk_DDR
Clock configurat for DDR mode
-
enumerator kFLEXSPIClk_SDR
-
enum _flexspi_read_sample_clk
FLEXSPI Read Sample Clock Source definition.
Values:
-
enumerator kFLEXSPIReadSampleClk_LoopbackInternally
-
enumerator kFLEXSPIReadSampleClk_LoopbackFromDqsPad
-
enumerator kFLEXSPIReadSampleClk_LoopbackFromSckPad
-
enumerator kFLEXSPIReadSampleClk_ExternalInputFromDqsPad
-
enumerator kFLEXSPIReadSampleClk_LoopbackInternally
Flash Type Definition.
Values:
-
enumerator kFLEXSPIDeviceType_SerialNOR
Flash device is Serial NOR
-
enumerator kFLEXSPIDeviceType_SerialNOR
Flash Configuration Command Type.
Values:
-
enumerator kDeviceConfigCmdType_Generic
Generic command, for example: configure dummy cycles, drive strength, etc
-
enumerator kDeviceConfigCmdType_QuadEnable
Quad Enable command
-
enumerator kDeviceConfigCmdType_Spi2Xpi
Switch from SPI to DPI/QPI/OPI mode
-
enumerator kDeviceConfigCmdType_Xpi2Spi
Switch from DPI/QPI/OPI to SPI mode
-
enumerator kDeviceConfigCmdType_Spi2NoCmd
Switch to 0-4-4/0-8-8 mode
-
enumerator kDeviceConfigCmdType_Reset
Reset device command
-
enumerator kDeviceConfigCmdType_Generic
-
enum _flexspi_serial_clk_freq
Defintions for FLEXSPI Serial Clock Frequency.
Values:
-
enumerator kFLEXSPISerialClk_NoChange
-
enumerator kFLEXSPISerialClk_30MHz
-
enumerator kFLEXSPISerialClk_50MHz
-
enumerator kFLEXSPISerialClk_60MHz
-
enumerator kFLEXSPISerialClk_75MHz
-
enumerator kFLEXSPISerialClk_80MHz
-
enumerator kFLEXSPISerialClk_100MHz
-
enumerator kFLEXSPISerialClk_133MHz
-
enumerator kFLEXSPISerialClk_166MHz
-
enumerator kFLEXSPISerialClk_200MHz
-
enumerator kFLEXSPISerialClk_NoChange
Misc feature bit definitions.
Values:
-
enumerator kFLEXSPIMiscOffset_DiffClkEnable
Bit for Differential clock enable
-
enumerator kFLEXSPIMiscOffset_Ck2Enable
Bit for CK2 enable
-
enumerator kFLEXSPIMiscOffset_ParallelEnable
Bit for Parallel mode enable
-
enumerator kFLEXSPIMiscOffset_WordAddressableEnable
Bit for Word Addressable enable
-
enumerator kFLEXSPIMiscOffset_SafeConfigFreqEnable
Bit for Safe Configuration Frequency enable
-
enumerator kFLEXSPIMiscOffset_PadSettingOverrideEnable
Bit for Pad setting override enable
-
enumerator kFLEXSPIMiscOffset_DdrModeEnable
Bit for DDR clock confiuration indication.
-
enumerator kFLEXSPIMiscOffset_UseValidTimeForAllFreq
Bit for DLLCR settings under all modes
-
enumerator kFLEXSPIMiscOffset_DiffClkEnable
Values:
-
enumerator kSerialNorType_StandardSPI
Device that support Standard SPI and Extended SPI mode
-
enumerator kSerialNorType_HyperBus
Device that supports HyperBus only
-
enumerator kSerialNorType_XPI
Device that works under DPI, QPI or OPI mode
-
enumerator kSerialNorType_NoCmd
Device that works under No command mode (XIP mode/Performance Enhance mode/continous read mode)
-
enumerator kSerialNorType_StandardSPI
Manufacturer ID.
Values:
-
enumerator kSerialFlash_ISSI_ManufacturerID
Manufacturer ID of the ISSI serial flash
-
enumerator kSerialFlash_Adesto_ManufacturerID
Manufacturer ID of the Adesto Technologies serial flash
-
enumerator kSerialFlash_Winbond_ManufacturerID
Manufacturer ID of the Winbond serial flash
-
enumerator kSerialFlash_Cypress_ManufacturerID
Manufacturer ID for Cypress
-
enumerator kSerialFlash_ISSI_ManufacturerID
-
enum _flexspi_nor_status
ROM FLEXSPI NOR flash status.
Values:
-
enumerator kStatus_ROM_FLEXSPI_SequenceExecutionTimeout
Status for Sequence Execution timeout
-
enumerator kStatus_ROM_FLEXSPI_InvalidSequence
Status for Invalid Sequence
-
enumerator kStatus_ROM_FLEXSPI_DeviceTimeout
Status for Device timeout
-
enumerator kStatus_FLEXSPINOR_DTRRead_DummyProbeFailed
Status for DDR Read dummy probe failure
-
enumerator kStatus_ROM_FLEXSPINOR_SFDP_NotFound
Status for SFDP read failure
-
enumerator kStatus_ROM_FLEXSPINOR_Flash_NotFound
Status for Flash detection failure
-
enumerator kStatus_ROM_FLEXSPI_SequenceExecutionTimeout
-
enum _flexspi_operation
FLEXSPI Operation Context.
Values:
-
enumerator kFLEXSPIOperation_Command
FLEXSPI operation: Only command, both TX and RX buffer are ignored.
-
enumerator kFLEXSPIOperation_Config
FLEXSPI operation: Configure device mode, the TX FIFO size is fixed in LUT.
-
enumerator kFLEXSPIOperation_Write
FLEXSPI operation: Write, only TX buffer is effective
-
enumerator kFLEXSPIOperation_Read
FLEXSPI operation: Read, only Rx Buffer is effective.
-
enumerator kFLEXSPIOperation_End
-
enumerator kFLEXSPIOperation_Command
-
typedef struct _flexspi_lut_seq flexspi_lut_seq_t
FLEXSPI LUT Sequence structure.
-
typedef struct _flexspi_mem_config flexspi_mem_config_t
FLEXSPI Memory Configuration Block.
-
typedef struct _flexspi_nor_config flexspi_nor_config_t
Serial NOR configuration block.
-
typedef enum _flexspi_operation flexspi_operation_t
FLEXSPI Operation Context.
-
typedef struct _flexspi_xfer flexspi_xfer_t
FLEXSPI Transfer Context.
-
status_t ROM_FLEXSPI_NorFlash_Init(uint32_t instance, flexspi_nor_config_t *config)
Initialize Serial NOR flash via FLEXSPI.
This function checks and initializes the FLEXSPI module for the other FLEXSPI APIs.
- Parameters:
instance – storage the instance of FLEXSPI.
config – A pointer to the storage for the driver runtime state.
- Return values:
kStatus_Success – Api was executed succesfuly.
kStatus_InvalidArgument – A invalid argument is provided.
kStatus_ROM_FLEXSPI_InvalidSequence – A invalid Sequence is provided.
kStatus_ROM_FLEXSPI_SequenceExecutionTimeout – Sequence Execution timeout.
kStatus_ROM_FLEXSPI_DeviceTimeout – the device timeout
-
status_t ROM_FLEXSPI_NorFlash_ProgramPage(uint32_t instance, flexspi_nor_config_t *config, uint32_t dstAddr, const uint32_t *src)
Program data to Serial NOR flash via FLEXSPI.
This function programs the NOR flash memory with the dest address for a given flash area as determined by the dst address and the length.
- Parameters:
instance – storage the instance of FLEXSPI.
config – A pointer to the storage for the driver runtime state.
dstAddr – A pointer to the desired flash memory to be programmed. NOTE: It is recommended that use page aligned access; If the dstAddr is not aligned to page,the driver automatically aligns address down with the page address.
src – A pointer to the source buffer of data that is to be programmed into the NOR flash.
- Return values:
kStatus_Success – Api was executed succesfuly.
kStatus_InvalidArgument – A invalid argument is provided.
kStatus_ROM_FLEXSPI_InvalidSequence – A invalid Sequence is provided.
kStatus_ROM_FLEXSPI_SequenceExecutionTimeout – Sequence Execution timeout.
kStatus_ROM_FLEXSPI_DeviceTimeout – the device timeout
-
status_t ROM_FLEXSPI_NorFlash_EraseSector(uint32_t instance, flexspi_nor_config_t *config, uint32_t address)
Erase one sector specified by address.
This function erases one of NOR flash sectors based on the desired address.
- Parameters:
instance – storage the index of FLEXSPI.
config – A pointer to the storage for the driver runtime state.
address – The start address of the desired NOR flash memory to be erased. NOTE: It is recommended that use sector-aligned access nor device; If dstAddr is not aligned with the sector,The driver automatically aligns address down with the sector address.
- Return values:
kStatus_Success – Api was executed succesfuly.
kStatus_InvalidArgument – A invalid argument is provided.
kStatus_ROM_FLEXSPI_InvalidSequence – A invalid Sequence is provided.
kStatus_ROM_FLEXSPI_SequenceExecutionTimeout – Sequence Execution timeout.
kStatus_ROM_FLEXSPI_DeviceTimeout – the device timeout
-
status_t ROM_FLEXSPI_NorFlash_EraseAll(uint32_t instance, flexspi_nor_config_t *config)
Erase all the Serial NOR flash connected on FLEXSPI.
- Parameters:
instance – storage the instance of FLEXSPI.
config – A pointer to the storage for the driver runtime state.
- Return values:
kStatus_Success – Api was executed succesfuly.
kStatus_InvalidArgument – A invalid argument is provided.
kStatus_ROM_FLEXSPI_InvalidSequence – A invalid Sequence is provided.
kStatus_ROM_FLEXSPI_SequenceExecutionTimeout – Sequence Execution timeout.
kStatus_ROM_FLEXSPI_DeviceTimeout – the device timeout
-
status_t ROM_FLEXSPI_NorFlash_Erase(uint32_t instance, flexspi_nor_config_t *config, uint32_t start, uint32_t length)
Erase Flash Region specified by address and length.
This function erases the appropriate number of flash sectors based on the desired start address and length.
- Parameters:
instance – storage the index of FLEXSPI.
config – A pointer to the storage for the driver runtime state.
start – The start address of the desired NOR flash memory to be erased. NOTE: It is recommended that use sector-aligned access NOR flash; If dstAddr is not aligned with the sector,the driver automatically aligns address down with the sector address.
length – The length, given in bytes to be erased. NOTE: It is recommended that use sector-aligned access NOR flash; If length is not aligned with the sector,the driver automatically aligns up with the sector.
- Return values:
kStatus_Success – Api was executed succesfuly.
kStatus_InvalidArgument – A invalid argument is provided.
kStatus_ROM_FLEXSPI_InvalidSequence – A invalid Sequence is provided.
kStatus_ROM_FLEXSPI_SequenceExecutionTimeout – Sequence Execution timeout.
kStatus_ROM_FLEXSPI_DeviceTimeout – the device timeout
-
status_t ROM_FLEXSPI_NorFlash_CommandXfer(uint32_t instance, flexspi_xfer_t *xfer)
FLEXSPI command.
This function is used to perform the command write sequence to the NOR flash.
- Parameters:
instance – storage the index of FLEXSPI.
xfer – A pointer to the storage FLEXSPI Transfer Context.
- Return values:
kStatus_Success – Api was executed succesfuly.
kStatus_InvalidArgument – A invalid argument is provided.
kStatus_ROM_FLEXSPI_InvalidSequence – A invalid Sequence is provided.
kStatus_ROM_FLEXSPI_SequenceExecutionTimeout – Sequence Execution timeout.
-
status_t ROM_FLEXSPI_NorFlash_UpdateLut(uint32_t instance, uint32_t seqIndex, const uint32_t *lutBase, uint32_t seqNumber)
Configure FLEXSPI Lookup table.
- Parameters:
instance – storage the index of FLEXSPI.
seqIndex – storage the sequence Id.
lutBase – A pointer to the look-up-table for command sequences.
seqNumber – storage sequence number.
- Return values:
kStatus_Success – Api was executed succesfuly.
kStatus_InvalidArgument – A invalid argument is provided.
kStatus_ROM_FLEXSPI_InvalidSequence – A invalid Sequence is provided.
kStatus_ROM_FLEXSPI_SequenceExecutionTimeout – Sequence Execution timeout.
-
void ROM_FLEXSPI_NorFlash_ClearCache(uint32_t instance)
Software reset for the FLEXSPI logic.
This function sets the software reset flags for both AHB and buffer domain and resets both AHB buffer and also IP FIFOs.
- Parameters:
instance – storage the index of FLEXSPI.
-
FSL_ROM_HAS_FLEXSPINOR_API
-
FSL_ROM_HAS_RUNBOOTLOADER_API
-
FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_GET_CONFIG
-
FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_FLASH_INIT
-
FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE
-
FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_SECTOR
-
FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_BLOCK
-
FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_ALL
-
FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_PAGE_PROGRAM
-
FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_UPDATE_LUT
-
FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_CMD_XFER
-
kROM_StatusGroup_FLEXSPI
ROM FLEXSPI status group number.
-
kROM_StatusGroup_FLEXSPINOR
ROM FLEXSPI NOR status group number.
-
FSL_ROM_FLEXSPI_LUT_SEQ(cmd0, pad0, op0, cmd1, pad1, op1)
-
FSL_ROM_FLEXSPI_BITMASK(bit_offset)
Generate bit mask.
-
FLEXSPI_CFG_BLK_TAG
FLEXSPI memory config block related defintions.
ascii “FCFB” Big Endian
-
FLEXSPI_CFG_BLK_VERSION
V1.4.0
-
CMD_SDR
-
CMD_DDR
-
RADDR_SDR
-
RADDR_DDR
-
CADDR_SDR
-
CADDR_DDR
-
MODE1_SDR
-
MODE1_DDR
-
MODE2_SDR
-
MODE2_DDR
-
MODE4_SDR
-
MODE4_DDR
-
MODE8_SDR
-
MODE8_DDR
-
WRITE_SDR
-
WRITE_DDR
-
READ_SDR
-
READ_DDR
-
LEARN_SDR
-
LEARN_DDR
-
DATSZ_SDR
-
DATSZ_DDR
-
DUMMY_SDR
-
DUMMY_DDR
-
DUMMY_RWDS_SDR
-
DUMMY_RWDS_DDR
-
JMP_ON_CS
-
STOP
-
FLEXSPI_1PAD
-
FLEXSPI_2PAD
-
FLEXSPI_4PAD
-
FLEXSPI_8PAD
-
NOR_CMD_INDEX_READ
-
NOR_CMD_INDEX_READSTATUS
-
NOR_CMD_INDEX_WRITEENABLE
-
NOR_CMD_INDEX_ERASESECTOR
-
NOR_CMD_INDEX_PAGEPROGRAM
-
NOR_CMD_INDEX_CHIPERASE
-
NOR_CMD_INDEX_DUMMY
-
NOR_CMD_INDEX_ERASEBLOCK
-
NOR_CMD_LUT_SEQ_IDX_READ
NOR LUT sequence index used for default LUT assignment NOTE: The will take effect if the lut sequences are not customized. READ LUT sequence id in lookupTable stored in config block
-
NOR_CMD_LUT_SEQ_IDX_READSTATUS
Read Status LUT sequence id in lookupTable stored in config block
-
NOR_CMD_LUT_SEQ_IDX_READSTATUS_XPI
Read status DPI/QPI/OPI sequence id in lookupTable stored in config block
-
NOR_CMD_LUT_SEQ_IDX_WRITEENABLE
Write Enable sequence id in lookupTable stored in config block
-
NOR_CMD_LUT_SEQ_IDX_WRITEENABLE_XPI
Write Enable DPI/QPI/OPI sequence id in lookupTable stored in config block
-
NOR_CMD_LUT_SEQ_IDX_ERASESECTOR
Erase Sector sequence id in lookupTable stored in config block
-
NOR_CMD_LUT_SEQ_IDX_ERASEBLOCK
Erase Block sequence id in lookupTable stored in config block
-
NOR_CMD_LUT_SEQ_IDX_PAGEPROGRAM
Program sequence id in lookupTable stored in config block
-
NOR_CMD_LUT_SEQ_IDX_CHIPERASE
Chip Erase sequence in lookupTable id stored in config block
-
NOR_CMD_LUT_SEQ_IDX_READ_SFDP
Read SFDP sequence in lookupTable id stored in config block
-
NOR_CMD_LUT_SEQ_IDX_RESTORE_NOCMD
Restore 0-4-4/0-8-8 mode sequence id in lookupTable stored in config block
-
NOR_CMD_LUT_SEQ_IDX_EXIT_NOCMD
Exit 0-4-4/0-8-8 mode sequence id in lookupTable stored in config blobk
-
uint8_t seqNum
Sequence Number, valid number: 1-16
-
uint8_t seqId
Sequence Index, valid number: 0-15
-
uint16_t reserved
-
uint8_t time_100ps
Data valid time, in terms of 100ps
-
uint8_t delay_cells
Data valid time, in terms of delay cells
-
uint32_t tag
[0x000-0x003] Tag, fixed value 0x42464346UL
-
uint32_t version
[0x004-0x007] Version,[31:24] -‘V’, [23:16] - Major, [15:8] - Minor, [7:0] - bugfix
-
uint32_t reserved0
[0x008-0x00b] Reserved for future use
-
uint8_t readSampleClkSrc
[0x00c-0x00c] Read Sample Clock Source, valid value: 0/1/3
-
uint8_t csHoldTime
[0x00d-0x00d] Data hold time, default value: 3
-
uint8_t csSetupTime
[0x00e-0x00e] Date setup time, default value: 3
-
uint8_t columnAddressWidth
[0x00f-0x00f] Column Address with, for HyperBus protocol, it is fixed to 3, For Serial NAND, need to refer to datasheet
-
uint8_t deviceModeCfgEnable
[0x010-0x010] Device Mode Configure enable flag, 1 - Enable, 0 - Disable
-
uint8_t deviceModeType
[0x011-0x011] Specify the configuration command type:Quad Enable, DPI/QPI/OPI switch, Generic configuration, etc.
-
uint16_t waitTimeCfgCommands
[0x012-0x013] Wait time for all configuration commands, unit: 100us, Used for DPI/QPI/OPI switch or reset command
-
flexspi_lut_seq_t deviceModeSeq
[0x014-0x017] Device mode sequence info, [7:0] - LUT sequence id, [15:8] - LUt sequence number, [31:16] Reserved
-
uint32_t deviceModeArg
[0x018-0x01b] Argument/Parameter for device configuration
-
uint8_t configCmdEnable
[0x01c-0x01c] Configure command Enable Flag, 1 - Enable, 0 - Disable
-
uint8_t configModeType[3]
[0x01d-0x01f] Configure Mode Type, similar as deviceModeTpe
-
flexspi_lut_seq_t configCmdSeqs[3]
[0x020-0x02b] Sequence info for Device Configuration command, similar as deviceModeSeq
-
uint32_t reserved1
[0x02c-0x02f] Reserved for future use
-
uint32_t configCmdArgs[3]
[0x030-0x03b] Arguments/Parameters for device Configuration commands
-
uint32_t reserved2
[0x03c-0x03f] Reserved for future use
-
uint32_t controllerMiscOption
[0x040-0x043] Controller Misc Options, see Misc feature bit definitions for more details
-
uint8_t deviceType
[0x044-0x044] Device Type: See Flash Type Definition for more details
-
uint8_t sflashPadType
[0x045-0x045] Serial Flash Pad Type: 1 - Single, 2 - Dual, 4 - Quad, 8 - Octal
-
uint8_t serialClkFreq
[0x046-0x046] Serial Flash Frequencey, device specific definitions, See System Boot Chapter for more details
-
uint8_t lutCustomSeqEnable
[0x047-0x047] LUT customization Enable, it is required if the program/erase cannot be done using 1 LUT sequence, currently, only applicable to HyperFLASH
-
uint32_t reserved3[2]
[0x048-0x04f] Reserved for future use
-
uint32_t sflashA1Size
[0x050-0x053] Size of Flash connected to A1
-
uint32_t sflashA2Size
[0x054-0x057] Size of Flash connected to A2
-
uint32_t sflashB1Size
[0x058-0x05b] Size of Flash connected to B1
-
uint32_t sflashB2Size
[0x05c-0x05f] Size of Flash connected to B2
-
uint32_t csPadSettingOverride
[0x060-0x063] CS pad setting override value
-
uint32_t sclkPadSettingOverride
[0x064-0x067] SCK pad setting override value
-
uint32_t dataPadSettingOverride
[0x068-0x06b] data pad setting override value
-
uint32_t dqsPadSettingOverride
[0x06c-0x06f] DQS pad setting override value
-
uint32_t timeoutInMs
[0x070-0x073] Timeout threshold for read status command
-
uint32_t commandInterval
[0x074-0x077] CS deselect interval between two commands
-
flexspi_dll_time_t dataValidTime[2]
[0x078-0x07b] CLK edge to data valid time for PORT A and PORT B
-
uint16_t busyOffset
[0x07c-0x07d] Busy offset, valid value: 0-31
-
uint16_t busyBitPolarity
[0x07e-0x07f] Busy flag polarity, 0 - busy flag is 1 when flash device is busy, 1 - busy flag is 0 when flash device is busy
-
uint32_t lookupTable[64]
[0x080-0x17f] Lookup table holds Flash command sequences
-
flexspi_lut_seq_t lutCustomSeq[12]
[0x180-0x1af] Customizable LUT Sequences
-
uint32_t reserved4[4]
[0x1b0-0x1bf] Reserved for future use
-
flexspi_mem_config_t memConfig
Common memory configuration info via FLEXSPI
-
uint32_t pageSize
Page size of Serial NOR
-
uint32_t sectorSize
Sector size of Serial NOR
-
uint8_t ipcmdSerialClkFreq
Clock frequency for IP command
-
uint8_t isUniformBlockSize
Sector/Block size is the same
-
uint8_t isDataOrderSwapped
Data order (D0, D1, D2, D3) is swapped (D1,D0, D3, D2)
-
uint8_t reserved0[1]
Reserved for future use
-
uint8_t serialNorType
Serial NOR Flash type: 0/1/2/3
-
uint8_t needExitNoCmdMode
Need to exit NoCmd mode before other IP command
-
uint8_t halfClkForNonReadCmd
Half the Serial Clock for non-read command: true/false
-
uint8_t needRestoreNoCmdMode
Need to Restore NoCmd mode after IP commmand execution
-
uint32_t blockSize
Block size
-
uint32_t reserve2[11]
Reserved for future use
-
flexspi_operation_t operation
FLEXSPI operation
-
uint32_t baseAddress
FLEXSPI operation base address
-
uint32_t seqId
Sequence Id
-
uint32_t seqNum
Sequence Number
-
bool isParallelModeEnable
Is a parallel transfer
-
uint32_t *txBuffer
Tx buffer
-
uint32_t txSize
Tx size in bytes
-
uint32_t *rxBuffer
Rx buffer
-
uint32_t rxSize
Rx size in bytes
-
FSL_ROM_ROMAPI_VERSION
ROMAPI version 1.1.1.
-
FSL_ROM_FLEXSPINOR_DRIVER_VERSION
ROM FLEXSPI NOR driver version 1.4.0.
-
struct _flexspi_lut_seq
- #include <fsl_romapi.h>
FLEXSPI LUT Sequence structure.
-
struct flexspi_dll_time_t
- #include <fsl_romapi.h>
-
struct _flexspi_mem_config
- #include <fsl_romapi.h>
FLEXSPI Memory Configuration Block.
-
struct _flexspi_nor_config
- #include <fsl_romapi.h>
Serial NOR configuration block.
-
struct _flexspi_xfer
- #include <fsl_romapi.h>
FLEXSPI Transfer Context.
RTWDOG: 32-bit Watchdog Timer
-
void RTWDOG_GetDefaultConfig(rtwdog_config_t *config)
Initializes the RTWDOG configuration structure.
This function initializes the RTWDOG configuration structure to default values. The default values are:
rtwdogConfig->enableRtwdog = true; rtwdogConfig->clockSource = kRTWDOG_ClockSource1; rtwdogConfig->prescaler = kRTWDOG_ClockPrescalerDivide1; rtwdogConfig->workMode.enableWait = true; rtwdogConfig->workMode.enableStop = false; rtwdogConfig->workMode.enableDebug = false; rtwdogConfig->testMode = kRTWDOG_TestModeDisabled; rtwdogConfig->enableUpdate = true; rtwdogConfig->enableInterrupt = false; rtwdogConfig->enableWindowMode = false; rtwdogConfig->windowValue = 0U; rtwdogConfig->timeoutValue = 0xFFFFU;
See also
rtwdog_config_t
- Parameters:
config – Pointer to the RTWDOG configuration structure.
- AT_QUICKACCESS_SECTION_CODE (void RTWDOG_Init(RTWDOG_Type *base, const rtwdog_config_t *config))
Initializes the RTWDOG module.
This function initializes the RTWDOG. To reconfigure the RTWDOG without forcing a reset first, enableUpdate must be set to true in the configuration.
Example:
rtwdog_config_t config; RTWDOG_GetDefaultConfig(&config); config.timeoutValue = 0x7ffU; config.enableUpdate = true; RTWDOG_Init(wdog_base,&config);
- Parameters:
base – RTWDOG peripheral base address.
config – The configuration of the RTWDOG.
-
void RTWDOG_Deinit(RTWDOG_Type *base)
De-initializes the RTWDOG module.
This function shuts down the RTWDOG. Ensure that the WDOG_CS.UPDATE is 1, which means that the register update is enabled.
- Parameters:
base – RTWDOG peripheral base address.
-
static inline void RTWDOG_Enable(RTWDOG_Type *base)
Enables the RTWDOG module.
This function writes a value into the WDOG_CS register to enable the RTWDOG. The WDOG_CS register is a write-once register. Ensure that the WCT window is still open and this register has not been written in this WCT while the function is called.
- Parameters:
base – RTWDOG peripheral base address.
-
static inline void RTWDOG_Disable(RTWDOG_Type *base)
Disables the RTWDOG module.
This function writes a value into the WDOG_CS register to disable the RTWDOG. The WDOG_CS register is a write-once register. Ensure that the WCT window is still open and this register has not been written in this WCT while the function is called.
- Parameters:
base – RTWDOG peripheral base address
-
static inline void RTWDOG_EnableInterrupts(RTWDOG_Type *base, uint32_t mask)
Enables the RTWDOG interrupt.
This function writes a value into the WDOG_CS register to enable the RTWDOG interrupt. The WDOG_CS register is a write-once register. Ensure that the WCT window is still open and this register has not been written in this WCT while the function is called.
- Parameters:
base – RTWDOG peripheral base address.
mask – The interrupts to enable. The parameter can be a combination of the following source if defined:
kRTWDOG_InterruptEnable
-
static inline void RTWDOG_DisableInterrupts(RTWDOG_Type *base, uint32_t mask)
Disables the RTWDOG interrupt.
This function writes a value into the WDOG_CS register to disable the RTWDOG interrupt. The WDOG_CS register is a write-once register. Ensure that the WCT window is still open and this register has not been written in this WCT while the function is called.
- Parameters:
base – RTWDOG peripheral base address.
mask – The interrupts to disabled. The parameter can be a combination of the following source if defined:
kRTWDOG_InterruptEnable
-
static inline uint32_t RTWDOG_GetStatusFlags(RTWDOG_Type *base)
Gets the RTWDOG all status flags.
This function gets all status flags.
Example to get the running flag:
uint32_t status; status = RTWDOG_GetStatusFlags(wdog_base) & kRTWDOG_RunningFlag;
See also
_rtwdog_status_flags_t
true: related status flag has been set.
false: related status flag is not set.
- Parameters:
base – RTWDOG peripheral base address
- Returns:
State of the status flag: asserted (true) or not-asserted (false).
-
static inline void RTWDOG_EnableWindowMode(RTWDOG_Type *base, bool enable)
Enables/disables the window mode.
- Parameters:
base – RTWDOG peripheral base address.
enable – Enables(true) or disables(false) the feature.
-
static inline uint32_t RTWDOG_CountToMesec(RTWDOG_Type *base, uint32_t count, uint32_t clockFreqInHz)
Converts raw count value to millisecond.
Note that if the clock frequency is too high the timeout period can be less than 1 ms. In this case this api will return 0 value.
- Parameters:
base – RTWDOG peripheral base address.
count – Raw count value.
clockFreqInHz – The frequency of the clock source RTWDOG uses.
- Returns:
Return converted time. Will return 0 if result is larger than 0xFFFFFFFF.
-
void RTWDOG_ClearStatusFlags(RTWDOG_Type *base, uint32_t mask)
Clears the RTWDOG flag.
This function clears the RTWDOG status flag.
Example to clear an interrupt flag:
RTWDOG_ClearStatusFlags(wdog_base,kRTWDOG_InterruptFlag);
- Parameters:
base – RTWDOG peripheral base address.
mask – The status flags to clear. The parameter can be any combination of the following values:
kRTWDOG_InterruptFlag
-
static inline void RTWDOG_SetTimeoutValue(RTWDOG_Type *base, uint16_t timeoutCount)
Sets the RTWDOG timeout value.
This function writes a timeout value into the WDOG_TOVAL register. The WDOG_TOVAL register is a write-once register. Ensure that the WCT window is still open and this register has not been written in this WCT while the function is called.
- Parameters:
base – RTWDOG peripheral base address
timeoutCount – RTWDOG timeout value, count of RTWDOG clock ticks.
-
static inline void RTWDOG_SetWindowValue(RTWDOG_Type *base, uint16_t windowValue)
Sets the RTWDOG window value.
This function writes a window value into the WDOG_WIN register. The WDOG_WIN register is a write-once register. Ensure that the WCT window is still open and this register has not been written in this WCT while the function is called.
- Parameters:
base – RTWDOG peripheral base address.
windowValue – RTWDOG window value.
- __STATIC_FORCEINLINE void RTWDOG_Unlock (RTWDOG_Type *base)
Unlocks the RTWDOG register written.
This function unlocks the RTWDOG register written.
Before starting the unlock sequence and following the configuration, disable the global interrupts. Otherwise, an interrupt could effectively invalidate the unlock sequence and the WCT may expire. After the configuration finishes, re-enable the global interrupts.
- Parameters:
base – RTWDOG peripheral base address
-
static inline void RTWDOG_Refresh(RTWDOG_Type *base)
Refreshes the RTWDOG timer.
This function feeds the RTWDOG. This function should be called before the Watchdog timer is in timeout. Otherwise, a reset is asserted.
- Parameters:
base – RTWDOG peripheral base address
-
static inline uint32_t RTWDOG_GetCounterValue(RTWDOG_Type *base)
Gets the RTWDOG counter value.
This function gets the RTWDOG counter value.
- Parameters:
base – RTWDOG peripheral base address.
- Returns:
Current RTWDOG counter value.
-
WDOG_FIRST_WORD_OF_UNLOCK
First word of unlock sequence
-
WDOG_SECOND_WORD_OF_UNLOCK
Second word of unlock sequence
-
WDOG_FIRST_WORD_OF_REFRESH
First word of refresh sequence
-
WDOG_SECOND_WORD_OF_REFRESH
Second word of refresh sequence
-
FSL_RTWDOG_DRIVER_VERSION
RTWDOG driver version.
-
enum _rtwdog_clock_source
Describes RTWDOG clock source.
Values:
-
enumerator kRTWDOG_ClockSource0
Clock source 0
-
enumerator kRTWDOG_ClockSource1
Clock source 1
-
enumerator kRTWDOG_ClockSource2
Clock source 2
-
enumerator kRTWDOG_ClockSource3
Clock source 3
-
enumerator kRTWDOG_ClockSource0
-
enum _rtwdog_clock_prescaler
Describes the selection of the clock prescaler.
Values:
-
enumerator kRTWDOG_ClockPrescalerDivide1
Divided by 1
-
enumerator kRTWDOG_ClockPrescalerDivide256
Divided by 256
-
enumerator kRTWDOG_ClockPrescalerDivide1
-
enum _rtwdog_test_mode
Describes RTWDOG test mode.
Values:
-
enumerator kRTWDOG_TestModeDisabled
Test Mode disabled
-
enumerator kRTWDOG_UserModeEnabled
User Mode enabled
-
enumerator kRTWDOG_LowByteTest
Test Mode enabled, only low byte is used
-
enumerator kRTWDOG_HighByteTest
Test Mode enabled, only high byte is used
-
enumerator kRTWDOG_TestModeDisabled
-
enum _rtwdog_interrupt_enable_t
RTWDOG interrupt configuration structure.
This structure contains the settings for all of the RTWDOG interrupt configurations.
Values:
-
enumerator kRTWDOG_InterruptEnable
Interrupt is generated before forcing a reset
-
enumerator kRTWDOG_InterruptEnable
-
enum _rtwdog_status_flags_t
RTWDOG status flags.
This structure contains the RTWDOG status flags for use in the RTWDOG functions.
Values:
-
enumerator kRTWDOG_RunningFlag
Running flag, set when RTWDOG is enabled
-
enumerator kRTWDOG_InterruptFlag
Interrupt flag, set when interrupt occurs
-
enumerator kRTWDOG_RunningFlag
-
typedef enum _rtwdog_clock_source rtwdog_clock_source_t
Describes RTWDOG clock source.
-
typedef enum _rtwdog_clock_prescaler rtwdog_clock_prescaler_t
Describes the selection of the clock prescaler.
-
typedef struct _rtwdog_work_mode rtwdog_work_mode_t
Defines RTWDOG work mode.
-
typedef enum _rtwdog_test_mode rtwdog_test_mode_t
Describes RTWDOG test mode.
-
typedef struct _rtwdog_config rtwdog_config_t
Describes RTWDOG configuration structure.
-
struct _rtwdog_work_mode
- #include <fsl_rtwdog.h>
Defines RTWDOG work mode.
Public Members
-
bool enableWait
Enables or disables RTWDOG in wait mode
-
bool enableStop
Enables or disables RTWDOG in stop mode
-
bool enableDebug
Enables or disables RTWDOG in debug mode
-
bool enableWait
-
struct _rtwdog_config
- #include <fsl_rtwdog.h>
Describes RTWDOG configuration structure.
Public Members
-
bool enableRtwdog
Enables or disables RTWDOG
-
rtwdog_clock_source_t clockSource
Clock source select
-
rtwdog_clock_prescaler_t prescaler
Clock prescaler value
-
rtwdog_work_mode_t workMode
Configures RTWDOG work mode in debug stop and wait mode
-
rtwdog_test_mode_t testMode
Configures RTWDOG test mode
-
bool enableUpdate
Update write-once register enable
-
bool enableInterrupt
Enables or disables RTWDOG interrupt
-
bool enableWindowMode
Enables or disables RTWDOG window mode
-
uint16_t windowValue
Window value
-
uint16_t timeoutValue
Timeout value
-
bool enableRtwdog
SAI: Serial Audio Interface
SAI Driver
-
void SAI_Init(I2S_Type *base)
Initializes the SAI peripheral.
This API gates the SAI clock. The SAI module can’t operate unless SAI_Init is called to enable the clock.
- Parameters:
base – SAI base pointer.
-
void SAI_Deinit(I2S_Type *base)
De-initializes the SAI peripheral.
This API gates the SAI clock. The SAI module can’t operate unless SAI_TxInit or SAI_RxInit is called to enable the clock.
- Parameters:
base – SAI base pointer.
-
void SAI_TxReset(I2S_Type *base)
Resets the SAI Tx.
This function enables the software reset and FIFO reset of SAI Tx. After reset, clear the reset bit.
- Parameters:
base – SAI base pointer
-
void SAI_RxReset(I2S_Type *base)
Resets the SAI Rx.
This function enables the software reset and FIFO reset of SAI Rx. After reset, clear the reset bit.
- Parameters:
base – SAI base pointer
-
void SAI_TxEnable(I2S_Type *base, bool enable)
Enables/disables the SAI Tx.
- Parameters:
base – SAI base pointer.
enable – True means enable SAI Tx, false means disable.
-
void SAI_RxEnable(I2S_Type *base, bool enable)
Enables/disables the SAI Rx.
- Parameters:
base – SAI base pointer.
enable – True means enable SAI Rx, false means disable.
-
static inline void SAI_TxSetBitClockDirection(I2S_Type *base, sai_master_slave_t masterSlave)
Set Rx bit clock direction.
Select bit clock direction, master or slave.
- Parameters:
base – SAI base pointer.
masterSlave – reference sai_master_slave_t.
-
static inline void SAI_RxSetBitClockDirection(I2S_Type *base, sai_master_slave_t masterSlave)
Set Rx bit clock direction.
Select bit clock direction, master or slave.
- Parameters:
base – SAI base pointer.
masterSlave – reference sai_master_slave_t.
-
static inline void SAI_RxSetFrameSyncDirection(I2S_Type *base, sai_master_slave_t masterSlave)
Set Rx frame sync direction.
Select frame sync direction, master or slave.
- Parameters:
base – SAI base pointer.
masterSlave – reference sai_master_slave_t.
-
static inline void SAI_TxSetFrameSyncDirection(I2S_Type *base, sai_master_slave_t masterSlave)
Set Tx frame sync direction.
Select frame sync direction, master or slave.
- Parameters:
base – SAI base pointer.
masterSlave – reference sai_master_slave_t.
-
void SAI_TxSetBitClockRate(I2S_Type *base, uint32_t sourceClockHz, uint32_t sampleRate, uint32_t bitWidth, uint32_t channelNumbers)
Transmitter bit clock rate configurations.
- Parameters:
base – SAI base pointer.
sourceClockHz – Bit clock source frequency.
sampleRate – Audio data sample rate.
bitWidth – Audio data bitWidth.
channelNumbers – Audio channel numbers.
-
void SAI_RxSetBitClockRate(I2S_Type *base, uint32_t sourceClockHz, uint32_t sampleRate, uint32_t bitWidth, uint32_t channelNumbers)
Receiver bit clock rate configurations.
- Parameters:
base – SAI base pointer.
sourceClockHz – Bit clock source frequency.
sampleRate – Audio data sample rate.
bitWidth – Audio data bitWidth.
channelNumbers – Audio channel numbers.
-
void SAI_TxSetBitclockConfig(I2S_Type *base, sai_master_slave_t masterSlave, sai_bit_clock_t *config)
Transmitter Bit clock configurations.
- Parameters:
base – SAI base pointer.
masterSlave – master or slave.
config – bit clock other configurations, can be NULL in slave mode.
-
void SAI_RxSetBitclockConfig(I2S_Type *base, sai_master_slave_t masterSlave, sai_bit_clock_t *config)
Receiver Bit clock configurations.
- Parameters:
base – SAI base pointer.
masterSlave – master or slave.
config – bit clock other configurations, can be NULL in slave mode.
-
void SAI_SetMasterClockConfig(I2S_Type *base, sai_master_clock_t *config)
Master clock configurations.
- Parameters:
base – SAI base pointer.
config – master clock configurations.
-
void SAI_TxSetFifoConfig(I2S_Type *base, sai_fifo_t *config)
SAI transmitter fifo configurations.
- Parameters:
base – SAI base pointer.
config – fifo configurations.
-
void SAI_RxSetFifoConfig(I2S_Type *base, sai_fifo_t *config)
SAI receiver fifo configurations.
- Parameters:
base – SAI base pointer.
config – fifo configurations.
-
void SAI_TxSetFrameSyncConfig(I2S_Type *base, sai_master_slave_t masterSlave, sai_frame_sync_t *config)
SAI transmitter Frame sync configurations.
- Parameters:
base – SAI base pointer.
masterSlave – master or slave.
config – frame sync configurations, can be NULL in slave mode.
-
void SAI_RxSetFrameSyncConfig(I2S_Type *base, sai_master_slave_t masterSlave, sai_frame_sync_t *config)
SAI receiver Frame sync configurations.
- Parameters:
base – SAI base pointer.
masterSlave – master or slave.
config – frame sync configurations, can be NULL in slave mode.
-
void SAI_TxSetSerialDataConfig(I2S_Type *base, sai_serial_data_t *config)
SAI transmitter Serial data configurations.
- Parameters:
base – SAI base pointer.
config – serial data configurations.
-
void SAI_RxSetSerialDataConfig(I2S_Type *base, sai_serial_data_t *config)
SAI receiver Serial data configurations.
- Parameters:
base – SAI base pointer.
config – serial data configurations.
-
void SAI_TxSetConfig(I2S_Type *base, sai_transceiver_t *config)
SAI transmitter configurations.
- Parameters:
base – SAI base pointer.
config – transmitter configurations.
-
void SAI_RxSetConfig(I2S_Type *base, sai_transceiver_t *config)
SAI receiver configurations.
- Parameters:
base – SAI base pointer.
config – receiver configurations.
-
void SAI_GetClassicI2SConfig(sai_transceiver_t *config, sai_word_width_t bitWidth, sai_mono_stereo_t mode, uint32_t saiChannelMask)
Get classic I2S mode configurations.
- Parameters:
config – transceiver configurations.
bitWidth – audio data bitWidth.
mode – audio data channel.
saiChannelMask – mask value of the channel to be enable.
-
void SAI_GetLeftJustifiedConfig(sai_transceiver_t *config, sai_word_width_t bitWidth, sai_mono_stereo_t mode, uint32_t saiChannelMask)
Get left justified mode configurations.
- Parameters:
config – transceiver configurations.
bitWidth – audio data bitWidth.
mode – audio data channel.
saiChannelMask – mask value of the channel to be enable.
-
void SAI_GetRightJustifiedConfig(sai_transceiver_t *config, sai_word_width_t bitWidth, sai_mono_stereo_t mode, uint32_t saiChannelMask)
Get right justified mode configurations.
- Parameters:
config – transceiver configurations.
bitWidth – audio data bitWidth.
mode – audio data channel.
saiChannelMask – mask value of the channel to be enable.
-
void SAI_GetTDMConfig(sai_transceiver_t *config, sai_frame_sync_len_t frameSyncWidth, sai_word_width_t bitWidth, uint32_t dataWordNum, uint32_t saiChannelMask)
Get TDM mode configurations.
- Parameters:
config – transceiver configurations.
frameSyncWidth – length of frame sync.
bitWidth – audio data word width.
dataWordNum – word number in one frame.
saiChannelMask – mask value of the channel to be enable.
-
void SAI_GetDSPConfig(sai_transceiver_t *config, sai_frame_sync_len_t frameSyncWidth, sai_word_width_t bitWidth, sai_mono_stereo_t mode, uint32_t saiChannelMask)
Get DSP mode configurations.
DSP/PCM MODE B configuration flow for TX. RX is similiar but uses SAI_RxSetConfig instead of SAI_TxSetConfig:
SAI_GetDSPConfig(config, kSAI_FrameSyncLenOneBitClk, bitWidth, kSAI_Stereo, channelMask) SAI_TxSetConfig(base, config)
Note
DSP mode is also called PCM mode which support MODE A and MODE B, DSP/PCM MODE A configuration flow. RX is similiar but uses SAI_RxSetConfig instead of SAI_TxSetConfig:
SAI_GetDSPConfig(config, kSAI_FrameSyncLenOneBitClk, bitWidth, kSAI_Stereo, channelMask) config->frameSync.frameSyncEarly = true; SAI_TxSetConfig(base, config)
- Parameters:
config – transceiver configurations.
frameSyncWidth – length of frame sync.
bitWidth – audio data bitWidth.
mode – audio data channel.
saiChannelMask – mask value of the channel to enable.
-
static inline uint32_t SAI_TxGetStatusFlag(I2S_Type *base)
Gets the SAI Tx status flag state.
- Parameters:
base – SAI base pointer
- Returns:
SAI Tx status flag value. Use the Status Mask to get the status value needed.
-
static inline void SAI_TxClearStatusFlags(I2S_Type *base, uint32_t mask)
Clears the SAI Tx status flag state.
- Parameters:
base – SAI base pointer
mask – State mask. It can be a combination of the following source if defined:
kSAI_WordStartFlag
kSAI_SyncErrorFlag
kSAI_FIFOErrorFlag
-
static inline uint32_t SAI_RxGetStatusFlag(I2S_Type *base)
Gets the SAI Tx status flag state.
- Parameters:
base – SAI base pointer
- Returns:
SAI Rx status flag value. Use the Status Mask to get the status value needed.
-
static inline void SAI_RxClearStatusFlags(I2S_Type *base, uint32_t mask)
Clears the SAI Rx status flag state.
- Parameters:
base – SAI base pointer
mask – State mask. It can be a combination of the following sources if defined.
kSAI_WordStartFlag
kSAI_SyncErrorFlag
kSAI_FIFOErrorFlag
-
void SAI_TxSoftwareReset(I2S_Type *base, sai_reset_type_t resetType)
Do software reset or FIFO reset .
FIFO reset means clear all the data in the FIFO, and make the FIFO pointer both to 0. Software reset means clear the Tx internal logic, including the bit clock, frame count etc. But software reset will not clear any configuration registers like TCR1~TCR5. This function will also clear all the error flags such as FIFO error, sync error etc.
- Parameters:
base – SAI base pointer
resetType – Reset type, FIFO reset or software reset
-
void SAI_RxSoftwareReset(I2S_Type *base, sai_reset_type_t resetType)
Do software reset or FIFO reset .
FIFO reset means clear all the data in the FIFO, and make the FIFO pointer both to 0. Software reset means clear the Rx internal logic, including the bit clock, frame count etc. But software reset will not clear any configuration registers like RCR1~RCR5. This function will also clear all the error flags such as FIFO error, sync error etc.
- Parameters:
base – SAI base pointer
resetType – Reset type, FIFO reset or software reset
-
void SAI_TxSetChannelFIFOMask(I2S_Type *base, uint8_t mask)
Set the Tx channel FIFO enable mask.
- Parameters:
base – SAI base pointer
mask – Channel enable mask, 0 means all channel FIFO disabled, 1 means channel 0 enabled, 3 means both channel 0 and channel 1 enabled.
-
void SAI_RxSetChannelFIFOMask(I2S_Type *base, uint8_t mask)
Set the Rx channel FIFO enable mask.
- Parameters:
base – SAI base pointer
mask – Channel enable mask, 0 means all channel FIFO disabled, 1 means channel 0 enabled, 3 means both channel 0 and channel 1 enabled.
-
void SAI_TxSetDataOrder(I2S_Type *base, sai_data_order_t order)
Set the Tx data order.
- Parameters:
base – SAI base pointer
order – Data order MSB or LSB
-
void SAI_RxSetDataOrder(I2S_Type *base, sai_data_order_t order)
Set the Rx data order.
- Parameters:
base – SAI base pointer
order – Data order MSB or LSB
-
void SAI_TxSetBitClockPolarity(I2S_Type *base, sai_clock_polarity_t polarity)
Set the Tx data order.
- Parameters:
base – SAI base pointer
polarity –
-
void SAI_RxSetBitClockPolarity(I2S_Type *base, sai_clock_polarity_t polarity)
Set the Rx data order.
- Parameters:
base – SAI base pointer
polarity –
-
void SAI_TxSetFrameSyncPolarity(I2S_Type *base, sai_clock_polarity_t polarity)
Set the Tx data order.
- Parameters:
base – SAI base pointer
polarity –
-
void SAI_RxSetFrameSyncPolarity(I2S_Type *base, sai_clock_polarity_t polarity)
Set the Rx data order.
- Parameters:
base – SAI base pointer
polarity –
-
void SAI_TxSetFIFOPacking(I2S_Type *base, sai_fifo_packing_t pack)
Set Tx FIFO packing feature.
- Parameters:
base – SAI base pointer.
pack – FIFO pack type. It is element of sai_fifo_packing_t.
-
void SAI_RxSetFIFOPacking(I2S_Type *base, sai_fifo_packing_t pack)
Set Rx FIFO packing feature.
- Parameters:
base – SAI base pointer.
pack – FIFO pack type. It is element of sai_fifo_packing_t.
-
static inline void SAI_TxSetFIFOErrorContinue(I2S_Type *base, bool isEnabled)
Set Tx FIFO error continue.
FIFO error continue mode means SAI will keep running while FIFO error occurred. If this feature not enabled, SAI will hang and users need to clear FEF flag in TCSR register.
- Parameters:
base – SAI base pointer.
isEnabled – Is FIFO error continue enabled, true means enable, false means disable.
-
static inline void SAI_RxSetFIFOErrorContinue(I2S_Type *base, bool isEnabled)
Set Rx FIFO error continue.
FIFO error continue mode means SAI will keep running while FIFO error occurred. If this feature not enabled, SAI will hang and users need to clear FEF flag in RCSR register.
- Parameters:
base – SAI base pointer.
isEnabled – Is FIFO error continue enabled, true means enable, false means disable.
-
static inline void SAI_TxEnableInterrupts(I2S_Type *base, uint32_t mask)
Enables the SAI Tx interrupt requests.
- Parameters:
base – SAI base pointer
mask – interrupt source The parameter can be a combination of the following sources if defined.
kSAI_WordStartInterruptEnable
kSAI_SyncErrorInterruptEnable
kSAI_FIFOWarningInterruptEnable
kSAI_FIFORequestInterruptEnable
kSAI_FIFOErrorInterruptEnable
-
static inline void SAI_RxEnableInterrupts(I2S_Type *base, uint32_t mask)
Enables the SAI Rx interrupt requests.
- Parameters:
base – SAI base pointer
mask – interrupt source The parameter can be a combination of the following sources if defined.
kSAI_WordStartInterruptEnable
kSAI_SyncErrorInterruptEnable
kSAI_FIFOWarningInterruptEnable
kSAI_FIFORequestInterruptEnable
kSAI_FIFOErrorInterruptEnable
-
static inline void SAI_TxDisableInterrupts(I2S_Type *base, uint32_t mask)
Disables the SAI Tx interrupt requests.
- Parameters:
base – SAI base pointer
mask – interrupt source The parameter can be a combination of the following sources if defined.
kSAI_WordStartInterruptEnable
kSAI_SyncErrorInterruptEnable
kSAI_FIFOWarningInterruptEnable
kSAI_FIFORequestInterruptEnable
kSAI_FIFOErrorInterruptEnable
-
static inline void SAI_RxDisableInterrupts(I2S_Type *base, uint32_t mask)
Disables the SAI Rx interrupt requests.
- Parameters:
base – SAI base pointer
mask – interrupt source The parameter can be a combination of the following sources if defined.
kSAI_WordStartInterruptEnable
kSAI_SyncErrorInterruptEnable
kSAI_FIFOWarningInterruptEnable
kSAI_FIFORequestInterruptEnable
kSAI_FIFOErrorInterruptEnable
-
static inline void SAI_TxEnableDMA(I2S_Type *base, uint32_t mask, bool enable)
Enables/disables the SAI Tx DMA requests.
- Parameters:
base – SAI base pointer
mask – DMA source The parameter can be combination of the following sources if defined.
kSAI_FIFOWarningDMAEnable
kSAI_FIFORequestDMAEnable
enable – True means enable DMA, false means disable DMA.
-
static inline void SAI_RxEnableDMA(I2S_Type *base, uint32_t mask, bool enable)
Enables/disables the SAI Rx DMA requests.
- Parameters:
base – SAI base pointer
mask – DMA source The parameter can be a combination of the following sources if defined.
kSAI_FIFOWarningDMAEnable
kSAI_FIFORequestDMAEnable
enable – True means enable DMA, false means disable DMA.
-
static inline uintptr_t SAI_TxGetDataRegisterAddress(I2S_Type *base, uint32_t channel)
Gets the SAI Tx data register address.
This API is used to provide a transfer address for the SAI DMA transfer configuration.
- Parameters:
base – SAI base pointer.
channel – Which data channel used.
- Returns:
data register address.
-
static inline uintptr_t SAI_RxGetDataRegisterAddress(I2S_Type *base, uint32_t channel)
Gets the SAI Rx data register address.
This API is used to provide a transfer address for the SAI DMA transfer configuration.
- Parameters:
base – SAI base pointer.
channel – Which data channel used.
- Returns:
data register address.
-
void SAI_WriteBlocking(I2S_Type *base, uint32_t channel, uint32_t bitWidth, uint8_t *buffer, uint32_t size)
Sends data using a blocking method.
Note
This function blocks by polling until data is ready to be sent.
- Parameters:
base – SAI base pointer.
channel – Data channel used.
bitWidth – How many bits in an audio word; usually 8/16/24/32 bits.
buffer – Pointer to the data to be written.
size – Bytes to be written.
-
void SAI_WriteMultiChannelBlocking(I2S_Type *base, uint32_t channel, uint32_t channelMask, uint32_t bitWidth, uint8_t *buffer, uint32_t size)
Sends data to multi channel using a blocking method.
Note
This function blocks by polling until data is ready to be sent.
- Parameters:
base – SAI base pointer.
channel – Data channel used.
channelMask – channel mask.
bitWidth – How many bits in an audio word; usually 8/16/24/32 bits.
buffer – Pointer to the data to be written.
size – Bytes to be written.
-
static inline void SAI_WriteData(I2S_Type *base, uint32_t channel, uint32_t data)
Writes data into SAI FIFO.
- Parameters:
base – SAI base pointer.
channel – Data channel used.
data – Data needs to be written.
-
void SAI_ReadBlocking(I2S_Type *base, uint32_t channel, uint32_t bitWidth, uint8_t *buffer, uint32_t size)
Receives data using a blocking method.
Note
This function blocks by polling until data is ready to be sent.
- Parameters:
base – SAI base pointer.
channel – Data channel used.
bitWidth – How many bits in an audio word; usually 8/16/24/32 bits.
buffer – Pointer to the data to be read.
size – Bytes to be read.
-
void SAI_ReadMultiChannelBlocking(I2S_Type *base, uint32_t channel, uint32_t channelMask, uint32_t bitWidth, uint8_t *buffer, uint32_t size)
Receives multi channel data using a blocking method.
Note
This function blocks by polling until data is ready to be sent.
- Parameters:
base – SAI base pointer.
channel – Data channel used.
channelMask – channel mask.
bitWidth – How many bits in an audio word; usually 8/16/24/32 bits.
buffer – Pointer to the data to be read.
size – Bytes to be read.
-
static inline uint32_t SAI_ReadData(I2S_Type *base, uint32_t channel)
Reads data from the SAI FIFO.
- Parameters:
base – SAI base pointer.
channel – Data channel used.
- Returns:
Data in SAI FIFO.
-
void SAI_TransferTxCreateHandle(I2S_Type *base, sai_handle_t *handle, sai_transfer_callback_t callback, void *userData)
Initializes the SAI Tx handle.
This function initializes the Tx handle for the SAI Tx transactional APIs. Call this function once to get the handle initialized.
- Parameters:
base – SAI base pointer
handle – SAI handle pointer.
callback – Pointer to the user callback function.
userData – User parameter passed to the callback function
-
void SAI_TransferRxCreateHandle(I2S_Type *base, sai_handle_t *handle, sai_transfer_callback_t callback, void *userData)
Initializes the SAI Rx handle.
This function initializes the Rx handle for the SAI Rx transactional APIs. Call this function once to get the handle initialized.
- Parameters:
base – SAI base pointer.
handle – SAI handle pointer.
callback – Pointer to the user callback function.
userData – User parameter passed to the callback function.
-
void SAI_TransferTxSetConfig(I2S_Type *base, sai_handle_t *handle, sai_transceiver_t *config)
SAI transmitter transfer configurations.
This function initializes the Tx, include bit clock, frame sync, master clock, serial data and fifo configurations.
- Parameters:
base – SAI base pointer.
handle – SAI handle pointer.
config – tranmitter configurations.
-
void SAI_TransferRxSetConfig(I2S_Type *base, sai_handle_t *handle, sai_transceiver_t *config)
SAI receiver transfer configurations.
This function initializes the Rx, include bit clock, frame sync, master clock, serial data and fifo configurations.
- Parameters:
base – SAI base pointer.
handle – SAI handle pointer.
config – receiver configurations.
-
status_t SAI_TransferSendNonBlocking(I2S_Type *base, sai_handle_t *handle, sai_transfer_t *xfer)
Performs an interrupt non-blocking send transfer on SAI.
Note
This API returns immediately after the transfer initiates. Call the SAI_TxGetTransferStatusIRQ to poll the transfer status and check whether the transfer is finished. If the return status is not kStatus_SAI_Busy, the transfer is finished.
- Parameters:
base – SAI base pointer.
handle – Pointer to the sai_handle_t structure which stores the transfer state.
xfer – Pointer to the sai_transfer_t structure.
- Return values:
kStatus_Success – Successfully started the data receive.
kStatus_SAI_TxBusy – Previous receive still not finished.
kStatus_InvalidArgument – The input parameter is invalid.
-
status_t SAI_TransferReceiveNonBlocking(I2S_Type *base, sai_handle_t *handle, sai_transfer_t *xfer)
Performs an interrupt non-blocking receive transfer on SAI.
Note
This API returns immediately after the transfer initiates. Call the SAI_RxGetTransferStatusIRQ to poll the transfer status and check whether the transfer is finished. If the return status is not kStatus_SAI_Busy, the transfer is finished.
- Parameters:
base – SAI base pointer
handle – Pointer to the sai_handle_t structure which stores the transfer state.
xfer – Pointer to the sai_transfer_t structure.
- Return values:
kStatus_Success – Successfully started the data receive.
kStatus_SAI_RxBusy – Previous receive still not finished.
kStatus_InvalidArgument – The input parameter is invalid.
-
status_t SAI_TransferGetSendCount(I2S_Type *base, sai_handle_t *handle, size_t *count)
Gets a set byte count.
- Parameters:
base – SAI base pointer.
handle – Pointer to the sai_handle_t structure which stores the transfer state.
count – Bytes count sent.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is not a non-blocking transaction currently in progress.
-
status_t SAI_TransferGetReceiveCount(I2S_Type *base, sai_handle_t *handle, size_t *count)
Gets a received byte count.
- Parameters:
base – SAI base pointer.
handle – Pointer to the sai_handle_t structure which stores the transfer state.
count – Bytes count received.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is not a non-blocking transaction currently in progress.
-
void SAI_TransferAbortSend(I2S_Type *base, sai_handle_t *handle)
Aborts the current send.
Note
This API can be called any time when an interrupt non-blocking transfer initiates to abort the transfer early.
- Parameters:
base – SAI base pointer.
handle – Pointer to the sai_handle_t structure which stores the transfer state.
-
void SAI_TransferAbortReceive(I2S_Type *base, sai_handle_t *handle)
Aborts the current IRQ receive.
Note
This API can be called when an interrupt non-blocking transfer initiates to abort the transfer early.
- Parameters:
base – SAI base pointer
handle – Pointer to the sai_handle_t structure which stores the transfer state.
-
void SAI_TransferTerminateSend(I2S_Type *base, sai_handle_t *handle)
Terminate all SAI send.
This function will clear all transfer slots buffered in the sai queue. If users only want to abort the current transfer slot, please call SAI_TransferAbortSend.
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
-
void SAI_TransferTerminateReceive(I2S_Type *base, sai_handle_t *handle)
Terminate all SAI receive.
This function will clear all transfer slots buffered in the sai queue. If users only want to abort the current transfer slot, please call SAI_TransferAbortReceive.
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
-
void SAI_TransferTxHandleIRQ(I2S_Type *base, sai_handle_t *handle)
Tx interrupt handler.
- Parameters:
base – SAI base pointer.
handle – Pointer to the sai_handle_t structure.
-
void SAI_TransferRxHandleIRQ(I2S_Type *base, sai_handle_t *handle)
Tx interrupt handler.
- Parameters:
base – SAI base pointer.
handle – Pointer to the sai_handle_t structure.
-
FSL_SAI_DRIVER_VERSION
Version 2.4.4
_sai_status_t, SAI return status.
Values:
-
enumerator kStatus_SAI_TxBusy
SAI Tx is busy.
-
enumerator kStatus_SAI_RxBusy
SAI Rx is busy.
-
enumerator kStatus_SAI_TxError
SAI Tx FIFO error.
-
enumerator kStatus_SAI_RxError
SAI Rx FIFO error.
-
enumerator kStatus_SAI_QueueFull
SAI transfer queue is full.
-
enumerator kStatus_SAI_TxIdle
SAI Tx is idle
-
enumerator kStatus_SAI_RxIdle
SAI Rx is idle
-
enumerator kStatus_SAI_TxBusy
_sai_channel_mask,.sai channel mask value, actual channel numbers is depend soc specific
Values:
-
enumerator kSAI_Channel0Mask
channel 0 mask value
-
enumerator kSAI_Channel1Mask
channel 1 mask value
-
enumerator kSAI_Channel2Mask
channel 2 mask value
-
enumerator kSAI_Channel3Mask
channel 3 mask value
-
enumerator kSAI_Channel4Mask
channel 4 mask value
-
enumerator kSAI_Channel5Mask
channel 5 mask value
-
enumerator kSAI_Channel6Mask
channel 6 mask value
-
enumerator kSAI_Channel7Mask
channel 7 mask value
-
enumerator kSAI_Channel0Mask
-
enum _sai_protocol
Define the SAI bus type.
Values:
-
enumerator kSAI_BusLeftJustified
Uses left justified format.
-
enumerator kSAI_BusRightJustified
Uses right justified format.
-
enumerator kSAI_BusI2S
Uses I2S format.
-
enumerator kSAI_BusPCMA
Uses I2S PCM A format.
-
enumerator kSAI_BusPCMB
Uses I2S PCM B format.
-
enumerator kSAI_BusLeftJustified
-
enum _sai_master_slave
Master or slave mode.
Values:
-
enumerator kSAI_Master
Master mode include bclk and frame sync
-
enumerator kSAI_Slave
Slave mode include bclk and frame sync
-
enumerator kSAI_Bclk_Master_FrameSync_Slave
bclk in master mode, frame sync in slave mode
-
enumerator kSAI_Bclk_Slave_FrameSync_Master
bclk in slave mode, frame sync in master mode
-
enumerator kSAI_Master
-
enum _sai_mono_stereo
Mono or stereo audio format.
Values:
-
enumerator kSAI_Stereo
Stereo sound.
-
enumerator kSAI_MonoRight
Only Right channel have sound.
-
enumerator kSAI_MonoLeft
Only left channel have sound.
-
enumerator kSAI_Stereo
-
enum _sai_data_order
SAI data order, MSB or LSB.
Values:
-
enumerator kSAI_DataLSB
LSB bit transferred first
-
enumerator kSAI_DataMSB
MSB bit transferred first
-
enumerator kSAI_DataLSB
-
enum _sai_clock_polarity
SAI clock polarity, active high or low.
Values:
-
enumerator kSAI_PolarityActiveHigh
Drive outputs on rising edge
-
enumerator kSAI_PolarityActiveLow
Drive outputs on falling edge
-
enumerator kSAI_SampleOnFallingEdge
Sample inputs on falling edge
-
enumerator kSAI_SampleOnRisingEdge
Sample inputs on rising edge
-
enumerator kSAI_PolarityActiveHigh
-
enum _sai_sync_mode
Synchronous or asynchronous mode.
Values:
-
enumerator kSAI_ModeAsync
Asynchronous mode
-
enumerator kSAI_ModeSync
Synchronous mode (with receiver or transmit)
-
enumerator kSAI_ModeSyncWithOtherTx
Synchronous with another SAI transmit
-
enumerator kSAI_ModeSyncWithOtherRx
Synchronous with another SAI receiver
-
enumerator kSAI_ModeAsync
-
enum _sai_bclk_source
Bit clock source.
Values:
-
enumerator kSAI_BclkSourceBusclk
Bit clock using bus clock
-
enumerator kSAI_BclkSourceMclkOption1
Bit clock MCLK option 1
-
enumerator kSAI_BclkSourceMclkOption2
Bit clock MCLK option2
-
enumerator kSAI_BclkSourceMclkOption3
Bit clock MCLK option3
-
enumerator kSAI_BclkSourceMclkDiv
Bit clock using master clock divider
-
enumerator kSAI_BclkSourceOtherSai0
Bit clock from other SAI device
-
enumerator kSAI_BclkSourceOtherSai1
Bit clock from other SAI device
-
enumerator kSAI_BclkSourceBusclk
_sai_interrupt_enable_t, The SAI interrupt enable flag
Values:
-
enumerator kSAI_WordStartInterruptEnable
Word start flag, means the first word in a frame detected
-
enumerator kSAI_SyncErrorInterruptEnable
Sync error flag, means the sync error is detected
-
enumerator kSAI_FIFOWarningInterruptEnable
FIFO warning flag, means the FIFO is empty
-
enumerator kSAI_FIFOErrorInterruptEnable
FIFO error flag
-
enumerator kSAI_FIFORequestInterruptEnable
FIFO request, means reached watermark
-
enumerator kSAI_WordStartInterruptEnable
_sai_dma_enable_t, The DMA request sources
Values:
-
enumerator kSAI_FIFOWarningDMAEnable
FIFO warning caused by the DMA request
-
enumerator kSAI_FIFORequestDMAEnable
FIFO request caused by the DMA request
-
enumerator kSAI_FIFOWarningDMAEnable
_sai_flags, The SAI status flag
Values:
-
enumerator kSAI_WordStartFlag
Word start flag, means the first word in a frame detected
-
enumerator kSAI_SyncErrorFlag
Sync error flag, means the sync error is detected
-
enumerator kSAI_FIFOErrorFlag
FIFO error flag
-
enumerator kSAI_FIFORequestFlag
FIFO request flag.
-
enumerator kSAI_FIFOWarningFlag
FIFO warning flag
-
enumerator kSAI_WordStartFlag
-
enum _sai_reset_type
The reset type.
Values:
-
enumerator kSAI_ResetTypeSoftware
Software reset, reset the logic state
-
enumerator kSAI_ResetTypeFIFO
FIFO reset, reset the FIFO read and write pointer
-
enumerator kSAI_ResetAll
All reset.
-
enumerator kSAI_ResetTypeSoftware
-
enum _sai_fifo_packing
The SAI packing mode The mode includes 8 bit and 16 bit packing.
Values:
-
enumerator kSAI_FifoPackingDisabled
Packing disabled
-
enumerator kSAI_FifoPacking8bit
8 bit packing enabled
-
enumerator kSAI_FifoPacking16bit
16bit packing enabled
-
enumerator kSAI_FifoPackingDisabled
-
enum _sai_sample_rate
Audio sample rate.
Values:
-
enumerator kSAI_SampleRate8KHz
Sample rate 8000 Hz
-
enumerator kSAI_SampleRate11025Hz
Sample rate 11025 Hz
-
enumerator kSAI_SampleRate12KHz
Sample rate 12000 Hz
-
enumerator kSAI_SampleRate16KHz
Sample rate 16000 Hz
-
enumerator kSAI_SampleRate22050Hz
Sample rate 22050 Hz
-
enumerator kSAI_SampleRate24KHz
Sample rate 24000 Hz
-
enumerator kSAI_SampleRate32KHz
Sample rate 32000 Hz
-
enumerator kSAI_SampleRate44100Hz
Sample rate 44100 Hz
-
enumerator kSAI_SampleRate48KHz
Sample rate 48000 Hz
-
enumerator kSAI_SampleRate96KHz
Sample rate 96000 Hz
-
enumerator kSAI_SampleRate192KHz
Sample rate 192000 Hz
-
enumerator kSAI_SampleRate384KHz
Sample rate 384000 Hz
-
enumerator kSAI_SampleRate8KHz
-
enum _sai_word_width
Audio word width.
Values:
-
enumerator kSAI_WordWidth8bits
Audio data width 8 bits
-
enumerator kSAI_WordWidth16bits
Audio data width 16 bits
-
enumerator kSAI_WordWidth24bits
Audio data width 24 bits
-
enumerator kSAI_WordWidth32bits
Audio data width 32 bits
-
enumerator kSAI_WordWidth8bits
-
enum _sai_data_pin_state
sai data pin state definition
Values:
-
enumerator kSAI_DataPinStateTriState
transmit data pins are tri-stated when slots are masked or channels are disabled
-
enumerator kSAI_DataPinStateOutputZero
transmit data pins are never tri-stated and will output zero when slots are masked or channel disabled
-
enumerator kSAI_DataPinStateTriState
-
enum _sai_fifo_combine
sai fifo combine mode definition
Values:
-
enumerator kSAI_FifoCombineDisabled
sai TX/RX fifo combine mode disabled
-
enumerator kSAI_FifoCombineModeEnabledOnRead
sai TX fifo combine mode enabled on FIFO reads
-
enumerator kSAI_FifoCombineModeEnabledOnWrite
sai TX fifo combine mode enabled on FIFO write
-
enumerator kSAI_RxFifoCombineModeEnabledOnWrite
sai RX fifo combine mode enabled on FIFO write
-
enumerator kSAI_RXFifoCombineModeEnabledOnRead
sai RX fifo combine mode enabled on FIFO reads
-
enumerator kSAI_FifoCombineModeEnabledOnReadWrite
sai TX/RX fifo combined mode enabled on FIFO read/writes
-
enumerator kSAI_FifoCombineDisabled
-
enum _sai_transceiver_type
sai transceiver type
Values:
-
enumerator kSAI_Transmitter
sai transmitter
-
enumerator kSAI_Receiver
sai receiver
-
enumerator kSAI_Transmitter
-
enum _sai_frame_sync_len
sai frame sync len
Values:
-
enumerator kSAI_FrameSyncLenOneBitClk
1 bit clock frame sync len for DSP mode
-
enumerator kSAI_FrameSyncLenPerWordWidth
Frame sync length decided by word width
-
enumerator kSAI_FrameSyncLenOneBitClk
-
typedef enum _sai_protocol sai_protocol_t
Define the SAI bus type.
-
typedef enum _sai_master_slave sai_master_slave_t
Master or slave mode.
-
typedef enum _sai_mono_stereo sai_mono_stereo_t
Mono or stereo audio format.
-
typedef enum _sai_data_order sai_data_order_t
SAI data order, MSB or LSB.
-
typedef enum _sai_clock_polarity sai_clock_polarity_t
SAI clock polarity, active high or low.
-
typedef enum _sai_sync_mode sai_sync_mode_t
Synchronous or asynchronous mode.
-
typedef enum _sai_bclk_source sai_bclk_source_t
Bit clock source.
-
typedef enum _sai_reset_type sai_reset_type_t
The reset type.
-
typedef enum _sai_fifo_packing sai_fifo_packing_t
The SAI packing mode The mode includes 8 bit and 16 bit packing.
-
typedef struct _sai_config sai_config_t
SAI user configuration structure.
-
typedef enum _sai_sample_rate sai_sample_rate_t
Audio sample rate.
-
typedef enum _sai_word_width sai_word_width_t
Audio word width.
-
typedef enum _sai_data_pin_state sai_data_pin_state_t
sai data pin state definition
-
typedef enum _sai_fifo_combine sai_fifo_combine_t
sai fifo combine mode definition
-
typedef enum _sai_transceiver_type sai_transceiver_type_t
sai transceiver type
-
typedef enum _sai_frame_sync_len sai_frame_sync_len_t
sai frame sync len
-
typedef struct _sai_transfer_format sai_transfer_format_t
sai transfer format
-
typedef struct _sai_master_clock sai_master_clock_t
master clock configurations
-
typedef struct _sai_fifo sai_fifo_t
sai fifo configurations
-
typedef struct _sai_bit_clock sai_bit_clock_t
sai bit clock configurations
-
typedef struct _sai_frame_sync sai_frame_sync_t
sai frame sync configurations
-
typedef struct _sai_serial_data sai_serial_data_t
sai serial data configurations
-
typedef struct _sai_transceiver sai_transceiver_t
sai transceiver configurations
-
typedef struct _sai_transfer sai_transfer_t
SAI transfer structure.
-
typedef struct _sai_handle sai_handle_t
-
typedef void (*sai_transfer_callback_t)(I2S_Type *base, sai_handle_t *handle, status_t status, void *userData)
SAI transfer callback prototype.
-
SAI_XFER_QUEUE_SIZE
SAI transfer queue size, user can refine it according to use case.
-
FSL_SAI_HAS_FIFO_EXTEND_FEATURE
sai fifo feature
-
struct _sai_config
- #include <fsl_sai.h>
SAI user configuration structure.
Public Members
-
sai_protocol_t protocol
Audio bus protocol in SAI
-
sai_sync_mode_t syncMode
SAI sync mode, control Tx/Rx clock sync
-
bool mclkOutputEnable
Master clock output enable, true means master clock divider enabled
-
sai_bclk_source_t bclkSource
Bit Clock source
-
sai_master_slave_t masterSlave
Master or slave
-
sai_protocol_t protocol
-
struct _sai_transfer_format
- #include <fsl_sai.h>
sai transfer format
Public Members
-
uint32_t sampleRate_Hz
Sample rate of audio data
-
uint32_t bitWidth
Data length of audio data, usually 8/16/24/32 bits
-
sai_mono_stereo_t stereo
Mono or stereo
-
uint32_t masterClockHz
Master clock frequency in Hz
-
uint8_t watermark
Watermark value
-
uint8_t channel
Transfer start channel
-
uint8_t channelMask
enabled channel mask value, reference _sai_channel_mask
-
uint8_t endChannel
end channel number
-
uint8_t channelNums
Total enabled channel numbers
-
sai_protocol_t protocol
Which audio protocol used
-
bool isFrameSyncCompact
True means Frame sync length is configurable according to bitWidth, false means frame sync length is 64 times of bit clock.
-
uint32_t sampleRate_Hz
-
struct _sai_master_clock
- #include <fsl_sai.h>
master clock configurations
Public Members
-
bool mclkOutputEnable
master clock output enable
-
uint32_t mclkHz
target mclk frequency
-
uint32_t mclkSourceClkHz
mclk source frequency
-
bool mclkOutputEnable
-
struct _sai_fifo
- #include <fsl_sai.h>
sai fifo configurations
Public Members
-
bool fifoContinueOneError
fifo continues when error occur
-
sai_fifo_combine_t fifoCombine
fifo combine mode
-
sai_fifo_packing_t fifoPacking
fifo packing mode
-
uint8_t fifoWatermark
fifo watermark
-
bool fifoContinueOneError
-
struct _sai_bit_clock
- #include <fsl_sai.h>
sai bit clock configurations
Public Members
-
bool bclkSrcSwap
bit clock source swap
-
bool bclkInputDelay
bit clock actually used by the transmitter is delayed by the pad output delay, this has effect of decreasing the data input setup time, but increasing the data output valid time .
-
sai_clock_polarity_t bclkPolarity
bit clock polarity
-
sai_bclk_source_t bclkSource
bit Clock source
-
bool bclkSrcSwap
-
struct _sai_frame_sync
- #include <fsl_sai.h>
sai frame sync configurations
Public Members
-
uint8_t frameSyncWidth
frame sync width in number of bit clocks
-
bool frameSyncEarly
TRUE is frame sync assert one bit before the first bit of frame FALSE is frame sync assert with the first bit of the frame
-
bool frameSyncGenerateOnDemand
internal frame sync is generated when FIFO waring flag is clear
-
sai_clock_polarity_t frameSyncPolarity
frame sync polarity
-
uint8_t frameSyncWidth
-
struct _sai_serial_data
- #include <fsl_sai.h>
sai serial data configurations
Public Members
-
sai_data_pin_state_t dataMode
sai data pin state when slots masked or channel disabled
-
sai_data_order_t dataOrder
configure whether the LSB or MSB is transmitted first
-
uint8_t dataWord0Length
configure the number of bits in the first word in each frame
-
uint8_t dataWordNLength
configure the number of bits in the each word in each frame, except the first word
-
uint8_t dataWordLength
used to record the data length for dma transfer
-
uint8_t dataFirstBitShifted
Configure the bit index for the first bit transmitted for each word in the frame
-
uint8_t dataWordNum
configure the number of words in each frame
-
uint32_t dataMaskedWord
configure whether the transmit word is masked
-
sai_data_pin_state_t dataMode
-
struct _sai_transceiver
- #include <fsl_sai.h>
sai transceiver configurations
Public Members
-
sai_serial_data_t serialData
serial data configurations
-
sai_frame_sync_t frameSync
ws configurations
-
sai_bit_clock_t bitClock
bit clock configurations
-
sai_fifo_t fifo
fifo configurations
-
sai_master_slave_t masterSlave
transceiver is master or slave
-
sai_sync_mode_t syncMode
transceiver sync mode
-
uint8_t startChannel
Transfer start channel
-
uint8_t channelMask
enabled channel mask value, reference _sai_channel_mask
-
uint8_t endChannel
end channel number
-
uint8_t channelNums
Total enabled channel numbers
-
sai_serial_data_t serialData
-
struct _sai_transfer
- #include <fsl_sai.h>
SAI transfer structure.
Public Members
-
uint8_t *data
Data start address to transfer.
-
size_t dataSize
Transfer size.
-
uint8_t *data
-
struct _sai_handle
- #include <fsl_sai.h>
SAI handle structure.
Public Members
-
I2S_Type *base
base address
-
uint32_t state
Transfer status
-
sai_transfer_callback_t callback
Callback function called at transfer event
-
void *userData
Callback parameter passed to callback function
-
uint8_t bitWidth
Bit width for transfer, 8/16/24/32 bits
-
uint8_t channel
Transfer start channel
-
uint8_t channelMask
enabled channel mask value, refernece _sai_channel_mask
-
uint8_t endChannel
end channel number
-
uint8_t channelNums
Total enabled channel numbers
-
sai_transfer_t saiQueue[(4U)]
Transfer queue storing queued transfer
-
size_t transferSize[(4U)]
Data bytes need to transfer
-
volatile uint8_t queueUser
Index for user to queue transfer
-
volatile uint8_t queueDriver
Index for driver to get the transfer data and size
-
uint8_t watermark
Watermark value
-
I2S_Type *base
SAI EDMA Driver
-
void SAI_TransferTxCreateHandleEDMA(I2S_Type *base, sai_edma_handle_t *handle, sai_edma_callback_t callback, void *userData, edma_handle_t *txDmaHandle)
Initializes the SAI eDMA handle.
This function initializes the SAI master DMA handle, which can be used for other SAI master transactional APIs. Usually, for a specified SAI instance, call this API once to get the initialized handle.
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
callback – Pointer to user callback function.
userData – User parameter passed to the callback function.
txDmaHandle – eDMA handle pointer, this handle shall be static allocated by users.
-
void SAI_TransferRxCreateHandleEDMA(I2S_Type *base, sai_edma_handle_t *handle, sai_edma_callback_t callback, void *userData, edma_handle_t *rxDmaHandle)
Initializes the SAI Rx eDMA handle.
This function initializes the SAI slave DMA handle, which can be used for other SAI master transactional APIs. Usually, for a specified SAI instance, call this API once to get the initialized handle.
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
callback – Pointer to user callback function.
userData – User parameter passed to the callback function.
rxDmaHandle – eDMA handle pointer, this handle shall be static allocated by users.
-
void SAI_TransferSetInterleaveType(sai_edma_handle_t *handle, sai_edma_interleave_t interleaveType)
Initializes the SAI interleave type.
This function initializes the SAI DMA handle member interleaveType, it shall be called only when application would like to use type kSAI_EDMAInterleavePerChannelBlock, since the default interleaveType is kSAI_EDMAInterleavePerChannelSample always
- Parameters:
handle – SAI eDMA handle pointer.
interleaveType – Multi channel interleave type.
-
void SAI_TransferTxSetConfigEDMA(I2S_Type *base, sai_edma_handle_t *handle, sai_transceiver_t *saiConfig)
Configures the SAI Tx.
Note
SAI eDMA supports data transfer in a multiple SAI channels if the FIFO Combine feature is supported. To activate the multi-channel transfer enable SAI channels by filling the channelMask of sai_transceiver_t with the corresponding values of _sai_channel_mask enum, enable the FIFO Combine mode by assigning kSAI_FifoCombineModeEnabledOnWrite to the fifoCombine member of sai_fifo_combine_t which is a member of sai_transceiver_t. This is an example of multi-channel data transfer configuration step.
sai_transceiver_t config; SAI_GetClassicI2SConfig(&config, kSAI_WordWidth16bits, kSAI_Stereo, kSAI_Channel0Mask|kSAI_Channel1Mask); config.fifo.fifoCombine = kSAI_FifoCombineModeEnabledOnWrite; SAI_TransferTxSetConfigEDMA(I2S0, &edmaHandle, &config);
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
saiConfig – sai configurations.
-
void SAI_TransferRxSetConfigEDMA(I2S_Type *base, sai_edma_handle_t *handle, sai_transceiver_t *saiConfig)
Configures the SAI Rx.
Note
SAI eDMA supports data transfer in a multiple SAI channels if the FIFO Combine feature is supported. To activate the multi-channel transfer enable SAI channels by filling the channelMask of sai_transceiver_t with the corresponding values of _sai_channel_mask enum, enable the FIFO Combine mode by assigning kSAI_FifoCombineModeEnabledOnRead to the fifoCombine member of sai_fifo_combine_t which is a member of sai_transceiver_t. This is an example of multi-channel data transfer configuration step.
sai_transceiver_t config; SAI_GetClassicI2SConfig(&config, kSAI_WordWidth16bits, kSAI_Stereo, kSAI_Channel0Mask|kSAI_Channel1Mask); config.fifo.fifoCombine = kSAI_FifoCombineModeEnabledOnRead; SAI_TransferRxSetConfigEDMA(I2S0, &edmaHandle, &config);
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
saiConfig – sai configurations.
-
status_t SAI_TransferSendEDMA(I2S_Type *base, sai_edma_handle_t *handle, sai_transfer_t *xfer)
Performs a non-blocking SAI transfer using DMA.
This function support multi channel transfer,
for the sai IP support fifo combine mode, application should enable the fifo combine mode, no limitation on channel numbers
for the sai IP not support fifo combine mode, sai edma provide another solution which using EDMA modulo feature, but support 2 or 4 channels only.
Note
This interface returns immediately after the transfer initiates. Call SAI_GetTransferStatus to poll the transfer status and check whether the SAI transfer is finished.
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
xfer – Pointer to the DMA transfer structure.
- Return values:
kStatus_Success – Start a SAI eDMA send successfully.
kStatus_InvalidArgument – The input argument is invalid.
kStatus_TxBusy – SAI is busy sending data.
-
status_t SAI_TransferReceiveEDMA(I2S_Type *base, sai_edma_handle_t *handle, sai_transfer_t *xfer)
Performs a non-blocking SAI receive using eDMA.
This function support multi channel transfer,
for the sai IP support fifo combine mode, application should enable the fifo combine mode, no limitation on channel numbers
for the sai IP not support fifo combine mode, sai edma provide another solution which using EDMA modulo feature, but support 2 or 4 channels only.
Note
This interface returns immediately after the transfer initiates. Call the SAI_GetReceiveRemainingBytes to poll the transfer status and check whether the SAI transfer is finished.
- Parameters:
base – SAI base pointer
handle – SAI eDMA handle pointer.
xfer – Pointer to DMA transfer structure.
- Return values:
kStatus_Success – Start a SAI eDMA receive successfully.
kStatus_InvalidArgument – The input argument is invalid.
kStatus_RxBusy – SAI is busy receiving data.
-
status_t SAI_TransferSendLoopEDMA(I2S_Type *base, sai_edma_handle_t *handle, sai_transfer_t *xfer, uint32_t loopTransferCount)
Performs a non-blocking SAI loop transfer using eDMA.
Once the loop transfer start, application can use function SAI_TransferAbortSendEDMA to stop the loop transfer.
Note
This function support loop transfer only,such as A->B->…->A, application must be aware of that the more counts of the loop transfer, then more tcd memory required, as the function use the tcd pool in sai_edma_handle_t, so application could redefine the SAI_XFER_QUEUE_SIZE to determine the proper TCD pool size. This function support one sai channel only.
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
xfer – Pointer to the DMA transfer structure, should be a array with elements counts >=1(loopTransferCount).
loopTransferCount – the counts of xfer array.
- Return values:
kStatus_Success – Start a SAI eDMA send successfully.
kStatus_InvalidArgument – The input argument is invalid.
-
status_t SAI_TransferReceiveLoopEDMA(I2S_Type *base, sai_edma_handle_t *handle, sai_transfer_t *xfer, uint32_t loopTransferCount)
Performs a non-blocking SAI loop transfer using eDMA.
Once the loop transfer start, application can use function SAI_TransferAbortReceiveEDMA to stop the loop transfer.
Note
This function support loop transfer only,such as A->B->…->A, application must be aware of that the more counts of the loop transfer, then more tcd memory required, as the function use the tcd pool in sai_edma_handle_t, so application could redefine the SAI_XFER_QUEUE_SIZE to determine the proper TCD pool size. This function support one sai channel only.
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
xfer – Pointer to the DMA transfer structure, should be a array with elements counts >=1(loopTransferCount).
loopTransferCount – the counts of xfer array.
- Return values:
kStatus_Success – Start a SAI eDMA receive successfully.
kStatus_InvalidArgument – The input argument is invalid.
-
void SAI_TransferTerminateSendEDMA(I2S_Type *base, sai_edma_handle_t *handle)
Terminate all SAI send.
This function will clear all transfer slots buffered in the sai queue. If users only want to abort the current transfer slot, please call SAI_TransferAbortSendEDMA.
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
-
void SAI_TransferTerminateReceiveEDMA(I2S_Type *base, sai_edma_handle_t *handle)
Terminate all SAI receive.
This function will clear all transfer slots buffered in the sai queue. If users only want to abort the current transfer slot, please call SAI_TransferAbortReceiveEDMA.
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
-
void SAI_TransferAbortSendEDMA(I2S_Type *base, sai_edma_handle_t *handle)
Aborts a SAI transfer using eDMA.
This function only aborts the current transfer slots, the other transfer slots’ information still kept in the handler. If users want to terminate all transfer slots, just call SAI_TransferTerminateSendEDMA.
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
-
void SAI_TransferAbortReceiveEDMA(I2S_Type *base, sai_edma_handle_t *handle)
Aborts a SAI receive using eDMA.
This function only aborts the current transfer slots, the other transfer slots’ information still kept in the handler. If users want to terminate all transfer slots, just call SAI_TransferTerminateReceiveEDMA.
- Parameters:
base – SAI base pointer
handle – SAI eDMA handle pointer.
-
status_t SAI_TransferGetSendCountEDMA(I2S_Type *base, sai_edma_handle_t *handle, size_t *count)
Gets byte count sent by SAI.
- Parameters:
base – SAI base pointer.
handle – SAI eDMA handle pointer.
count – Bytes count sent by SAI.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is no non-blocking transaction in progress.
-
status_t SAI_TransferGetReceiveCountEDMA(I2S_Type *base, sai_edma_handle_t *handle, size_t *count)
Gets byte count received by SAI.
- Parameters:
base – SAI base pointer
handle – SAI eDMA handle pointer.
count – Bytes count received by SAI.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is no non-blocking transaction in progress.
-
uint32_t SAI_TransferGetValidTransferSlotsEDMA(I2S_Type *base, sai_edma_handle_t *handle)
Gets valid transfer slot.
This function can be used to query the valid transfer request slot that the application can submit. It should be called in the critical section, that means the application could call it in the corresponding callback function or disable IRQ before calling it in the application, otherwise, the returned value may not correct.
- Parameters:
base – SAI base pointer
handle – SAI eDMA handle pointer.
- Return values:
valid – slot count that application submit.
-
FSL_SAI_EDMA_DRIVER_VERSION
Version 2.7.1
-
enum _sai_edma_interleave
sai interleave type
Values:
-
enumerator kSAI_EDMAInterleavePerChannelSample
-
enumerator kSAI_EDMAInterleavePerChannelBlock
-
enumerator kSAI_EDMAInterleavePerChannelSample
-
typedef struct sai_edma_handle sai_edma_handle_t
-
typedef void (*sai_edma_callback_t)(I2S_Type *base, sai_edma_handle_t *handle, status_t status, void *userData)
SAI eDMA transfer callback function for finish and error.
-
typedef enum _sai_edma_interleave sai_edma_interleave_t
sai interleave type
-
struct sai_edma_handle
- #include <fsl_sai_edma.h>
SAI DMA transfer handle, users should not touch the content of the handle.
Public Members
-
edma_handle_t *dmaHandle
DMA handler for SAI send
-
uint8_t nbytes
eDMA minor byte transfer count initially configured.
-
uint8_t bytesPerFrame
Bytes in a frame
-
uint8_t channelMask
Enabled channel mask value, reference _sai_channel_mask
-
uint8_t channelNums
total enabled channel nums
-
uint8_t channel
Which data channel
-
uint8_t count
The transfer data count in a DMA request
-
uint32_t state
Internal state for SAI eDMA transfer
-
sai_edma_callback_t callback
Callback for users while transfer finish or error occurs
-
void *userData
User callback parameter
-
uint8_t tcd[((4U) + 1U) * sizeof(edma_tcd_t)]
TCD pool for eDMA transfer.
-
sai_transfer_t saiQueue[(4U)]
Transfer queue storing queued transfer.
-
size_t transferSize[(4U)]
Data bytes need to transfer
-
sai_edma_interleave_t interleaveType
Transfer interleave type
-
volatile uint8_t queueUser
Index for user to queue transfer.
-
volatile uint8_t queueDriver
Index for driver to get the transfer data and size
-
edma_handle_t *dmaHandle
SEMC: Smart External DRAM Controller Driver
-
void SEMC_GetDefaultConfig(semc_config_t *config)
Gets the SEMC default basic configuration structure.
The purpose of this API is to get the default SEMC configure structure for SEMC_Init(). User may use the initialized structure unchanged in SEMC_Init(), or modify some fields of the structure before calling SEMC_Init(). Example:
semc_config_t config; SEMC_GetDefaultConfig(&config);
- Parameters:
config – The SEMC configuration structure pointer.
-
void SEMC_Init(SEMC_Type *base, semc_config_t *configure)
Initializes SEMC. This function ungates the SEMC clock and initializes SEMC. This function must be called before calling any other SEMC driver functions.
- Parameters:
base – SEMC peripheral base address.
configure – The SEMC configuration structure pointer.
-
void SEMC_Deinit(SEMC_Type *base)
Deinitializes the SEMC module and gates the clock.
This function gates the SEMC clock. As a result, the SEMC module doesn’t work after calling this function, for some IDE, calling this API may cause the next downloading operation failed. so, please call this API cautiously. Additional, users can using “#define FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL (1)” to disable the clock control operation in drivers.
- Parameters:
base – SEMC peripheral base address.
-
status_t SEMC_ConfigureSDRAM(SEMC_Type *base, semc_sdram_cs_t cs, semc_sdram_config_t *config, uint32_t clkSrc_Hz)
Configures SDRAM controller in SEMC.
- Parameters:
base – SEMC peripheral base address.
cs – The chip selection.
config – The sdram configuration.
clkSrc_Hz – The SEMC clock frequency.
-
status_t SEMC_ConfigureNAND(SEMC_Type *base, semc_nand_config_t *config, uint32_t clkSrc_Hz)
Configures NAND controller in SEMC.
- Parameters:
base – SEMC peripheral base address.
config – The nand configuration.
clkSrc_Hz – The SEMC clock frequency.
-
status_t SEMC_ConfigureNOR(SEMC_Type *base, semc_nor_config_t *config, uint32_t clkSrc_Hz)
Configures NOR controller in SEMC.
- Parameters:
base – SEMC peripheral base address.
config – The nor configuration.
clkSrc_Hz – The SEMC clock frequency.
-
status_t SEMC_ConfigureSRAMWithChipSelection(SEMC_Type *base, semc_sram_cs_t cs, semc_sram_config_t *config, uint32_t clkSrc_Hz)
Configures SRAM controller in SEMC.
- Parameters:
base – SEMC peripheral base address.
cs – The chip selection.
config – The sram configuration.
clkSrc_Hz – The SEMC clock frequency.
-
status_t SEMC_ConfigureSRAM(SEMC_Type *base, semc_sram_config_t *config, uint32_t clkSrc_Hz)
Configures SRAM controller in SEMC.
- Deprecated:
Do not use this function. It has been superceded by SEMC_ConfigureSRAMWithChipSelection.
- Parameters:
base – SEMC peripheral base address.
config – The sram configuration.
clkSrc_Hz – The SEMC clock frequency.
-
status_t SEMC_ConfigureDBI(SEMC_Type *base, semc_dbi_config_t *config, uint32_t clkSrc_Hz)
Configures DBI controller in SEMC.
- Parameters:
base – SEMC peripheral base address.
config – The dbi configuration.
clkSrc_Hz – The SEMC clock frequency.
-
static inline void SEMC_EnableInterrupts(SEMC_Type *base, uint32_t mask)
Enables the SEMC interrupt.
This function enables the SEMC interrupts according to the provided mask. The mask is a logical OR of enumeration members. See semc_interrupt_enable_t. For example, to enable the IP command done and error interrupt, do the following.
SEMC_EnableInterrupts(ENET, kSEMC_IPCmdDoneInterrupt | kSEMC_IPCmdErrInterrupt);
- Parameters:
base – SEMC peripheral base address.
mask – SEMC interrupts to enable. This is a logical OR of the enumeration :: semc_interrupt_enable_t.
-
static inline void SEMC_DisableInterrupts(SEMC_Type *base, uint32_t mask)
Disables the SEMC interrupt.
This function disables the SEMC interrupts according to the provided mask. The mask is a logical OR of enumeration members. See semc_interrupt_enable_t. For example, to disable the IP command done and error interrupt, do the following.
SEMC_DisableInterrupts(ENET, kSEMC_IPCmdDoneInterrupt | kSEMC_IPCmdErrInterrupt);
- Parameters:
base – SEMC peripheral base address.
mask – SEMC interrupts to disable. This is a logical OR of the enumeration :: semc_interrupt_enable_t.
-
static inline bool SEMC_GetStatusFlag(SEMC_Type *base)
Gets the SEMC status.
This function gets the SEMC interrupts event status. User can use the a logical OR of enumeration member as a mask. See semc_interrupt_enable_t.
- Parameters:
base – SEMC peripheral base address.
- Returns:
status flag, use status flag in semc_interrupt_enable_t to get the related status.
-
static inline void SEMC_ClearStatusFlags(SEMC_Type *base, uint32_t mask)
Clears the SEMC status flag state.
The following status register flags can be cleared SEMC interrupt status.
- Parameters:
base – SEMC base pointer
mask – The status flag mask, a logical OR of enumeration member semc_interrupt_enable_t.
-
static inline bool SEMC_IsInIdle(SEMC_Type *base)
Check if SEMC is in idle.
- Parameters:
base – SEMC peripheral base address.
- Returns:
True SEMC is in idle, false is not in idle.
-
status_t SEMC_SendIPCommand(SEMC_Type *base, semc_mem_type_t memType, uint32_t address, uint32_t command, uint32_t write, uint32_t *read)
SEMC IP command access.
- Parameters:
base – SEMC peripheral base address.
memType – SEMC memory type. refer to “semc_mem_type_t”
address – SEMC device address.
command – SEMC IP command. For NAND device, we should use the SEMC_BuildNandIPCommand to get the right nand command. For NOR/DBI device, take refer to “semc_ipcmd_nor_dbi_t”. For SRAM device, take refer to “semc_ipcmd_sram_t”. For SDRAM device, take refer to “semc_ipcmd_sdram_t”.
write – Data for write access.
read – Data pointer for read data out.
-
static inline uint16_t SEMC_BuildNandIPCommand(uint8_t userCommand, semc_ipcmd_nand_addrmode_t addrMode, semc_ipcmd_nand_cmdmode_t cmdMode)
Build SEMC IP command for NAND.
This function build SEMC NAND IP command. The command is build of user command code, SEMC address mode and SEMC command mode.
- Parameters:
userCommand – NAND device normal command.
addrMode – NAND address mode. Refer to “semc_ipcmd_nand_addrmode_t”.
cmdMode – NAND command mode. Refer to “semc_ipcmd_nand_cmdmode_t”.
-
static inline bool SEMC_IsNandReady(SEMC_Type *base)
Check if the NAND device is ready.
- Parameters:
base – SEMC peripheral base address.
- Returns:
True NAND is ready, false NAND is not ready.
-
status_t SEMC_IPCommandNandWrite(SEMC_Type *base, uint32_t address, uint8_t *data, uint32_t size_bytes)
SEMC NAND device memory write through IP command.
- Parameters:
base – SEMC peripheral base address.
address – SEMC NAND device address.
data – Data for write access.
size_bytes – Data length.
-
status_t SEMC_IPCommandNandRead(SEMC_Type *base, uint32_t address, uint8_t *data, uint32_t size_bytes)
SEMC NAND device memory read through IP command.
- Parameters:
base – SEMC peripheral base address.
address – SEMC NAND device address.
data – Data pointer for data read out.
size_bytes – Data length.
-
status_t SEMC_IPCommandNorWrite(SEMC_Type *base, uint32_t address, uint8_t *data, uint32_t size_bytes)
SEMC NOR device memory write through IP command.
- Parameters:
base – SEMC peripheral base address.
address – SEMC NOR device address.
data – Data for write access.
size_bytes – Data length.
-
status_t SEMC_IPCommandNorRead(SEMC_Type *base, uint32_t address, uint8_t *data, uint32_t size_bytes)
SEMC NOR device memory read through IP command.
- Parameters:
base – SEMC peripheral base address.
address – SEMC NOR device address.
data – Data pointer for data read out.
size_bytes – Data length.
-
FSL_SEMC_DRIVER_VERSION
SEMC driver version.
SEMC status, _semc_status.
Values:
-
enumerator kStatus_SEMC_InvalidDeviceType
Invalid device type.
-
enumerator kStatus_SEMC_IpCommandExecutionError
IP command execution error.
-
enumerator kStatus_SEMC_AxiCommandExecutionError
AXI command execution error.
-
enumerator kStatus_SEMC_InvalidMemorySize
Invalid memory sie.
-
enumerator kStatus_SEMC_InvalidIpcmdDataSize
Invalid IP command data size.
-
enumerator kStatus_SEMC_InvalidAddressPortWidth
Invalid address port width.
-
enumerator kStatus_SEMC_InvalidDataPortWidth
Invalid data port width.
-
enumerator kStatus_SEMC_InvalidSwPinmuxSelection
Invalid SW pinmux selection.
-
enumerator kStatus_SEMC_InvalidBurstLength
Invalid burst length
-
enumerator kStatus_SEMC_InvalidColumnAddressBitWidth
Invalid column address bit width.
-
enumerator kStatus_SEMC_InvalidBaseAddress
Invalid base address.
-
enumerator kStatus_SEMC_InvalidTimerSetting
Invalid timer setting.
-
enumerator kStatus_SEMC_InvalidDeviceType
-
enum _semc_mem_type
SEMC memory device type.
Values:
-
enumerator kSEMC_MemType_SDRAM
SDRAM
-
enumerator kSEMC_MemType_SRAM
SRAM
-
enumerator kSEMC_MemType_NOR
NOR
-
enumerator kSEMC_MemType_NAND
NAND
-
enumerator kSEMC_MemType_8080
-
enumerator kSEMC_MemType_SDRAM
-
enum _semc_waitready_polarity
SEMC WAIT/RDY polarity.
Values:
-
enumerator kSEMC_LowActive
Low active.
-
enumerator kSEMC_HighActive
High active.
-
enumerator kSEMC_LowActive
-
enum _semc_sdram_cs
SEMC SDRAM Chip selection .
Values:
-
enumerator kSEMC_SDRAM_CS0
SEMC SDRAM CS0.
-
enumerator kSEMC_SDRAM_CS1
SEMC SDRAM CS1.
-
enumerator kSEMC_SDRAM_CS2
SEMC SDRAM CS2.
-
enumerator kSEMC_SDRAM_CS3
SEMC SDRAM CS3.
-
enumerator kSEMC_SDRAM_CS0
-
enum _semc_sram_cs
SEMC SRAM Chip selection .
Values:
-
enumerator kSEMC_SRAM_CS0
SEMC SRAM CS0.
-
enumerator kSEMC_SRAM_CS0
-
enum _semc_nand_access_type
SEMC NAND device type.
Values:
-
enumerator kSEMC_NAND_ACCESS_BY_AXI
Access to NAND flash by AXI bus.
-
enumerator kSEMC_NAND_ACCESS_BY_IPCMD
Access to NAND flash by IP bus.
-
enumerator kSEMC_NAND_ACCESS_BY_AXI
-
enum _semc_interrupt_enable
SEMC interrupts .
Values:
-
enumerator kSEMC_IPCmdDoneInterrupt
Ip command done interrupt.
-
enumerator kSEMC_IPCmdErrInterrupt
Ip command error interrupt.
-
enumerator kSEMC_AXICmdErrInterrupt
AXI command error interrupt.
-
enumerator kSEMC_AXIBusErrInterrupt
AXI bus error interrupt.
-
enumerator kSEMC_IPCmdDoneInterrupt
-
enum _semc_ipcmd_datasize
SEMC IP command data size in bytes.
Values:
-
enumerator kSEMC_IPcmdDataSize_1bytes
The IP command data size 1 byte.
-
enumerator kSEMC_IPcmdDataSize_2bytes
The IP command data size 2 byte.
-
enumerator kSEMC_IPcmdDataSize_3bytes
The IP command data size 3 byte.
-
enumerator kSEMC_IPcmdDataSize_4bytes
The IP command data size 4 byte.
-
enumerator kSEMC_IPcmdDataSize_1bytes
-
enum _semc_refresh_time
SEMC auto-refresh timing.
Values:
-
enumerator kSEMC_RefreshThreeClocks
The refresh timing with three bus clocks.
-
enumerator kSEMC_RefreshSixClocks
The refresh timing with six bus clocks.
-
enumerator kSEMC_RefreshNineClocks
The refresh timing with nine bus clocks.
-
enumerator kSEMC_RefreshThreeClocks
-
enum _semc_caslatency
CAS latency.
Values:
-
enumerator kSEMC_LatencyOne
Latency 1.
-
enumerator kSEMC_LatencyTwo
Latency 2.
-
enumerator kSEMC_LatencyThree
Latency 3.
-
enumerator kSEMC_LatencyOne
-
enum _semc_sdram_column_bit_num
SEMC sdram column address bit number.
Values:
-
enumerator kSEMC_SdramColunm_12bit
12 bit.
-
enumerator kSEMC_SdramColunm_11bit
11 bit.
-
enumerator kSEMC_SdramColunm_10bit
10 bit.
-
enumerator kSEMC_SdramColunm_9bit
9 bit.
-
enumerator kSEMC_SdramColunm_8bit
8 bit.
-
enumerator kSEMC_SdramColunm_12bit
-
enum _semc_sdram_burst_len
SEMC sdram burst length.
Values:
-
enumerator kSEMC_Sdram_BurstLen1
According to ERR050577, Auto-refresh command may possibly fail to be triggered during long time back-to-back write (or read) when SDRAM controller’s burst length is greater than 1. Burst length 1
-
enumerator kSEMC_Sdram_BurstLen1
-
enum _semc_nand_column_bit_num
SEMC nand column address bit number.
Values:
-
enumerator kSEMC_NandColum_16bit
16 bit.
-
enumerator kSEMC_NandColum_15bit
15 bit.
-
enumerator kSEMC_NandColum_14bit
14 bit.
-
enumerator kSEMC_NandColum_13bit
13 bit.
-
enumerator kSEMC_NandColum_12bit
12 bit.
-
enumerator kSEMC_NandColum_11bit
11 bit.
-
enumerator kSEMC_NandColum_10bit
10 bit.
-
enumerator kSEMC_NandColum_9bit
9 bit.
-
enumerator kSEMC_NandColum_16bit
-
enum _semc_nand_burst_len
SEMC nand burst length.
Values:
-
enumerator kSEMC_Nand_BurstLen1
Burst length 1
-
enumerator kSEMC_Nand_BurstLen2
Burst length 2
-
enumerator kSEMC_Nand_BurstLen4
Burst length 4
-
enumerator kSEMC_Nand_BurstLen8
Burst length 8
-
enumerator kSEMC_Nand_BurstLen16
Burst length 16
-
enumerator kSEMC_Nand_BurstLen32
Burst length 32
-
enumerator kSEMC_Nand_BurstLen64
Burst length 64
-
enumerator kSEMC_Nand_BurstLen1
-
enum _semc_norsram_column_bit_num
SEMC nor/sram column address bit number.
Values:
-
enumerator kSEMC_NorColum_12bit
12 bit.
-
enumerator kSEMC_NorColum_11bit
11 bit.
-
enumerator kSEMC_NorColum_10bit
10 bit.
-
enumerator kSEMC_NorColum_9bit
9 bit.
-
enumerator kSEMC_NorColum_8bit
8 bit.
-
enumerator kSEMC_NorColum_7bit
7 bit.
-
enumerator kSEMC_NorColum_6bit
6 bit.
-
enumerator kSEMC_NorColum_5bit
5 bit.
-
enumerator kSEMC_NorColum_4bit
4 bit.
-
enumerator kSEMC_NorColum_3bit
3 bit.
-
enumerator kSEMC_NorColum_2bit
2 bit.
-
enumerator kSEMC_NorColum_12bit
-
enum _semc_norsram_burst_len
SEMC nor/sram burst length.
Values:
-
enumerator kSEMC_Nor_BurstLen1
Burst length 1
-
enumerator kSEMC_Nor_BurstLen2
Burst length 2
-
enumerator kSEMC_Nor_BurstLen4
Burst length 4
-
enumerator kSEMC_Nor_BurstLen8
Burst length 8
-
enumerator kSEMC_Nor_BurstLen16
Burst length 16
-
enumerator kSEMC_Nor_BurstLen32
Burst length 32
-
enumerator kSEMC_Nor_BurstLen64
Burst length 64
-
enumerator kSEMC_Nor_BurstLen1
-
enum _semc_dbi_column_bit_num
SEMC dbi column address bit number.
Values:
-
enumerator kSEMC_Dbi_Colum_12bit
12 bit.
-
enumerator kSEMC_Dbi_Colum_11bit
11 bit.
-
enumerator kSEMC_Dbi_Colum_10bit
10 bit.
-
enumerator kSEMC_Dbi_Colum_9bit
9 bit.
-
enumerator kSEMC_Dbi_Colum_8bit
8 bit.
-
enumerator kSEMC_Dbi_Colum_7bit
7 bit.
-
enumerator kSEMC_Dbi_Colum_6bit
6 bit.
-
enumerator kSEMC_Dbi_Colum_5bit
5 bit.
-
enumerator kSEMC_Dbi_Colum_4bit
4 bit.
-
enumerator kSEMC_Dbi_Colum_3bit
3 bit.
-
enumerator kSEMC_Dbi_Colum_2bit
2 bit.
-
enumerator kSEMC_Dbi_Colum_12bit
-
enum _semc_dbi_burst_len
SEMC dbi burst length.
Values:
-
enumerator kSEMC_Dbi_BurstLen1
Burst length 1
-
enumerator kSEMC_Dbi_BurstLen2
Burst length 2
-
enumerator kSEMC_Dbi_Dbi_BurstLen4
Burst length 4
-
enumerator kSEMC_Dbi_BurstLen8
Burst length 8
-
enumerator kSEMC_Dbi_BurstLen16
Burst length 16
-
enumerator kSEMC_Dbi_BurstLen32
Burst length 32
-
enumerator kSEMC_Dbi_BurstLen64
Burst length 64
-
enumerator kSEMC_Dbi_BurstLen1
-
enum _semc_iomux_pin
SEMC IOMUXC.
Values:
-
enumerator kSEMC_MUXA8
MUX A8 pin.
-
enumerator kSEMC_MUXCSX0
MUX CSX0 pin
-
enumerator kSEMC_MUXCSX1
MUX CSX1 Pin.
-
enumerator kSEMC_MUXCSX2
MUX CSX2 Pin.
-
enumerator kSEMC_MUXCSX3
MUX CSX3 Pin.
-
enumerator kSEMC_MUXRDY
MUX RDY pin.
-
enumerator kSEMC_MUXA8
-
enum _semc_iomux_nora27_pin
SEMC NOR/PSRAM Address bit 27 A27.
Values:
-
enumerator kSEMC_MORA27_NONE
No NOR/SRAM A27 pin.
-
enumerator kSEMC_NORA27_MUXCSX3
MUX CSX3 Pin.
-
enumerator kSEMC_NORA27_MUXRDY
MUX RDY pin.
-
enumerator kSEMC_MORA27_NONE
-
enum _semc_port_size
SEMC port size.
Values:
-
enumerator kSEMC_PortSize8Bit
8-Bit port size.
-
enumerator kSEMC_PortSize16Bit
16-Bit port size.
-
enumerator kSEMC_PortSize8Bit
-
enum _semc_addr_mode
SEMC address mode.
Values:
-
enumerator kSEMC_AddrDataMux
SEMC address/data mux mode.
-
enumerator kSEMC_AdvAddrdataMux
Advanced address/data mux mode.
-
enumerator kSEMC_AddrDataNonMux
Address/data non-mux mode.
-
enumerator kSEMC_AddrDataMux
-
enum _semc_dqs_mode
SEMC DQS read strobe mode.
Values:
-
enumerator kSEMC_Loopbackinternal
Dummy read strobe loopbacked internally.
-
enumerator kSEMC_Loopbackdqspad
Dummy read strobe loopbacked from DQS pad.
-
enumerator kSEMC_Loopbackinternal
-
enum _semc_adv_polarity
SEMC ADV signal active polarity.
Values:
-
enumerator kSEMC_AdvActiveLow
Adv active low.
-
enumerator kSEMC_AdvActiveHigh
Adv active high.
-
enumerator kSEMC_AdvActiveLow
-
enum _semc_sync_mode
SEMC sync mode.
Values:
-
enumerator kSEMC_AsyncMode
Async mode.
-
enumerator kSEMC_SyncMode
Sync mode.
-
enumerator kSEMC_AsyncMode
-
enum _semc_adv_level_control
SEMC ADV signal level control.
Values:
-
enumerator kSEMC_AdvHigh
Adv is high during address hold state.
-
enumerator kSEMC_AdvLow
Adv is low during address hold state.
-
enumerator kSEMC_AdvHigh
-
enum _semc_rdy_polarity
SEMC RDY signal active polarity.
Values:
-
enumerator kSEMC_RdyActiveLow
Adv active low.
-
enumerator kSEMC_RdyActivehigh
Adv active low.
-
enumerator kSEMC_RdyActiveLow
-
enum _semc_ipcmd_nand_addrmode
SEMC IP command for NAND: address mode.
Values:
-
enumerator kSEMC_NANDAM_ColumnRow
Address mode: column and row address(5Byte-CA0/CA1/RA0/RA1/RA2).
-
enumerator kSEMC_NANDAM_ColumnCA0
Address mode: column address only(1 Byte-CA0).
-
enumerator kSEMC_NANDAM_ColumnCA0CA1
Address mode: column address only(2 Byte-CA0/CA1).
-
enumerator kSEMC_NANDAM_RawRA0
Address mode: row address only(1 Byte-RA0).
-
enumerator kSEMC_NANDAM_RawRA0RA1
Address mode: row address only(2 Byte-RA0/RA1).
-
enumerator kSEMC_NANDAM_RawRA0RA1RA2
Address mode: row address only(3 Byte-RA0).
-
enumerator kSEMC_NANDAM_ColumnRow
-
enum _semc_ipcmd_nand_cmdmode
SEMC IP command for NAND: command mode.
Values:
-
enumerator kSEMC_NANDCM_Command
command.
-
enumerator kSEMC_NANDCM_CommandHold
Command hold.
-
enumerator kSEMC_NANDCM_CommandAddress
Command address.
-
enumerator kSEMC_NANDCM_CommandAddressHold
Command address hold.
-
enumerator kSEMC_NANDCM_CommandAddressRead
Command address read.
-
enumerator kSEMC_NANDCM_CommandAddressWrite
Command address write.
-
enumerator kSEMC_NANDCM_CommandRead
Command read.
-
enumerator kSEMC_NANDCM_CommandWrite
Command write.
-
enumerator kSEMC_NANDCM_Read
Read.
-
enumerator kSEMC_NANDCM_Write
Write.
-
enumerator kSEMC_NANDCM_Command
-
enum _semc_nand_address_option
SEMC NAND address option.
Values:
-
enumerator kSEMC_NandAddrOption_5byte_CA2RA3
CA0+CA1+RA0+RA1+RA2
-
enumerator kSEMC_NandAddrOption_4byte_CA2RA2
CA0+CA1+RA0+RA1
-
enumerator kSEMC_NandAddrOption_3byte_CA2RA1
CA0+CA1+RA0
-
enumerator kSEMC_NandAddrOption_4byte_CA1RA3
CA0+RA0+RA1+RA2
-
enumerator kSEMC_NandAddrOption_3byte_CA1RA2
CA0+RA0+RA1
-
enumerator kSEMC_NandAddrOption_2byte_CA1RA1
CA0+RA0
-
enumerator kSEMC_NandAddrOption_5byte_CA2RA3
-
enum _semc_ipcmd_nor_dbi
SEMC IP command for NOR.
Values:
-
enumerator kSEMC_NORDBICM_Read
NOR read.
-
enumerator kSEMC_NORDBICM_Write
NOR write.
-
enumerator kSEMC_NORDBICM_Read
-
enum _semc_ipcmd_sram
SEMC IP command for SRAM.
Values:
-
enumerator kSEMC_SRAMCM_ArrayRead
SRAM memory array read.
-
enumerator kSEMC_SRAMCM_ArrayWrite
SRAM memory array write.
-
enumerator kSEMC_SRAMCM_RegRead
SRAM memory register read.
-
enumerator kSEMC_SRAMCM_RegWrite
SRAM memory register write.
-
enumerator kSEMC_SRAMCM_ArrayRead
-
enum _semc_ipcmd_sdram
SEMC IP command for SDARM.
Values:
-
enumerator kSEMC_SDRAMCM_Read
SDRAM memory read.
-
enumerator kSEMC_SDRAMCM_Write
SDRAM memory write.
-
enumerator kSEMC_SDRAMCM_Modeset
SDRAM MODE SET.
-
enumerator kSEMC_SDRAMCM_Active
SDRAM active.
-
enumerator kSEMC_SDRAMCM_AutoRefresh
SDRAM auto-refresh.
-
enumerator kSEMC_SDRAMCM_SelfRefresh
SDRAM self-refresh.
-
enumerator kSEMC_SDRAMCM_Precharge
SDRAM precharge.
-
enumerator kSEMC_SDRAMCM_Prechargeall
SDRAM precharge all.
-
enumerator kSEMC_SDRAMCM_Read
-
typedef enum _semc_mem_type semc_mem_type_t
SEMC memory device type.
-
typedef enum _semc_waitready_polarity semc_waitready_polarity_t
SEMC WAIT/RDY polarity.
-
typedef enum _semc_sdram_cs semc_sdram_cs_t
SEMC SDRAM Chip selection .
-
typedef enum _semc_sram_cs semc_sram_cs_t
SEMC SRAM Chip selection .
-
typedef enum _semc_nand_access_type semc_nand_access_type_t
SEMC NAND device type.
-
typedef enum _semc_interrupt_enable semc_interrupt_enable_t
SEMC interrupts .
-
typedef enum _semc_ipcmd_datasize semc_ipcmd_datasize_t
SEMC IP command data size in bytes.
-
typedef enum _semc_refresh_time semc_refresh_time_t
SEMC auto-refresh timing.
-
typedef enum _semc_caslatency semc_caslatency_t
CAS latency.
-
typedef enum _semc_sdram_column_bit_num semc_sdram_column_bit_num_t
SEMC sdram column address bit number.
-
typedef enum _semc_sdram_burst_len sem_sdram_burst_len_t
SEMC sdram burst length.
-
typedef enum _semc_nand_column_bit_num semc_nand_column_bit_num_t
SEMC nand column address bit number.
-
typedef enum _semc_nand_burst_len sem_nand_burst_len_t
SEMC nand burst length.
-
typedef enum _semc_norsram_column_bit_num semc_norsram_column_bit_num_t
SEMC nor/sram column address bit number.
-
typedef enum _semc_norsram_burst_len sem_norsram_burst_len_t
SEMC nor/sram burst length.
-
typedef enum _semc_dbi_column_bit_num semc_dbi_column_bit_num_t
SEMC dbi column address bit number.
-
typedef enum _semc_dbi_burst_len sem_dbi_burst_len_t
SEMC dbi burst length.
-
typedef enum _semc_iomux_pin semc_iomux_pin
SEMC IOMUXC.
-
typedef enum _semc_iomux_nora27_pin semc_iomux_nora27_pin
SEMC NOR/PSRAM Address bit 27 A27.
-
typedef enum _semc_port_size smec_port_size_t
SEMC port size.
-
typedef enum _semc_addr_mode semc_addr_mode_t
SEMC address mode.
-
typedef enum _semc_dqs_mode semc_dqs_mode_t
SEMC DQS read strobe mode.
-
typedef enum _semc_adv_polarity semc_adv_polarity_t
SEMC ADV signal active polarity.
-
typedef enum _semc_sync_mode semc_sync_mode_t
SEMC sync mode.
-
typedef enum _semc_adv_level_control semc_adv_level_control_t
SEMC ADV signal level control.
-
typedef enum _semc_rdy_polarity semc_rdy_polarity_t
SEMC RDY signal active polarity.
-
typedef enum _semc_ipcmd_nand_addrmode semc_ipcmd_nand_addrmode_t
SEMC IP command for NAND: address mode.
-
typedef enum _semc_ipcmd_nand_cmdmode semc_ipcmd_nand_cmdmode_t
SEMC IP command for NAND: command mode.
-
typedef enum _semc_nand_address_option semc_nand_address_option_t
SEMC NAND address option.
-
typedef enum _semc_ipcmd_nor_dbi semc_ipcmd_nor_dbi_t
SEMC IP command for NOR.
-
typedef enum _semc_ipcmd_sram semc_ipcmd_sram_t
SEMC IP command for SRAM.
-
typedef enum _semc_ipcmd_sdram semc_ipcmd_sdram_t
SEMC IP command for SDARM.
-
typedef struct _semc_sdram_config semc_sdram_config_t
SEMC SDRAM configuration structure.
The memory size in the configuration is in the unit of KB. So memsize_kbytes should be set as 2^2, 2^3, 2^4 .etc which is base 2KB exponential function. Take refer to BR0~BR3 register in RM for details.
The prescalePeriod_N16Cycle is in unit of 16 clock cycle. It is a exception for prescaleTimer_n16cycle = 0, it means the prescaler timer period is 256 * 16 clock cycles. For precalerIf precalerTimer_n16cycle not equal to 0, The prescaler timer period is prescalePeriod_N16Cycle * 16 clock cycles. idleTimeout_NprescalePeriod, refreshUrgThreshold_NprescalePeriod, refreshPeriod_NprescalePeriod are similar to prescalePeriod_N16Cycle.
-
typedef struct _semc_nand_timing_config semc_nand_timing_config_t
SEMC NAND device timing configuration structure.
-
typedef struct _semc_nand_config semc_nand_config_t
SEMC NAND configuration structure.
-
typedef struct _semc_nor_config semc_nor_config_t
SEMC NOR configuration structure.
-
typedef struct _semc_sram_config semc_sram_config_t
SEMC SRAM configuration structure.
-
typedef struct _semc_dbi_config semc_dbi_config_t
SEMC DBI configuration structure.
-
typedef struct _semc_queuea_weight_struct semc_queuea_weight_struct_t
SEMC AXI queue a weight setting structure.
-
typedef union _semc_queuea_weight semc_queuea_weight_t
SEMC AXI queue a weight setting union.
-
typedef struct _semc_queueb_weight_struct semc_queueb_weight_struct_t
SEMC AXI queue b weight setting structure.
-
typedef union _semc_queueb_weight semc_queueb_weight_t
SEMC AXI queue b weight setting union.
-
typedef struct _semc_axi_queueweight semc_axi_queueweight_t
SEMC AXI queue weight setting.
-
typedef struct _semc_config_t semc_config_t
SEMC configuration structure.
busTimeoutCycles: when busTimeoutCycles is zero, the bus timeout cycle is 255*1024. otherwise the bus timeout cycles is busTimeoutCycles*1024. cmdTimeoutCycles: is used for command execution timeout cycles. it’s similar to the busTimeoutCycles.
-
struct _semc_sdram_config
- #include <fsl_semc.h>
SEMC SDRAM configuration structure.
The memory size in the configuration is in the unit of KB. So memsize_kbytes should be set as 2^2, 2^3, 2^4 .etc which is base 2KB exponential function. Take refer to BR0~BR3 register in RM for details.
The prescalePeriod_N16Cycle is in unit of 16 clock cycle. It is a exception for prescaleTimer_n16cycle = 0, it means the prescaler timer period is 256 * 16 clock cycles. For precalerIf precalerTimer_n16cycle not equal to 0, The prescaler timer period is prescalePeriod_N16Cycle * 16 clock cycles. idleTimeout_NprescalePeriod, refreshUrgThreshold_NprescalePeriod, refreshPeriod_NprescalePeriod are similar to prescalePeriod_N16Cycle.
Public Members
-
semc_iomux_pin csxPinMux
CS pin mux. The kSEMC_MUXA8 is not valid in sdram pin mux setting.
-
uint32_t address
The base address.
-
uint32_t memsize_kbytes
The memory size in unit of kbytes.
-
smec_port_size_t portSize
Port size.
-
sem_sdram_burst_len_t burstLen
Burst length.
-
semc_sdram_column_bit_num_t columnAddrBitNum
Column address bit number.
-
semc_caslatency_t casLatency
CAS latency.
-
uint8_t tPrecharge2Act_Ns
Precharge to active wait time in unit of nanosecond.
-
uint8_t tAct2ReadWrite_Ns
Act to read/write wait time in unit of nanosecond.
-
uint8_t tRefreshRecovery_Ns
Refresh recovery time in unit of nanosecond.
-
uint8_t tWriteRecovery_Ns
write recovery time in unit of nanosecond.
-
uint8_t tCkeOff_Ns
CKE off minimum time in unit of nanosecond.
-
uint8_t tAct2Prechage_Ns
Active to precharge in unit of nanosecond.
-
uint8_t tSelfRefRecovery_Ns
Self refresh recovery time in unit of nanosecond.
-
uint8_t tRefresh2Refresh_Ns
Refresh to refresh wait time in unit of nanosecond.
-
uint8_t tAct2Act_Ns
Active to active wait time in unit of nanosecond.
-
uint32_t tPrescalePeriod_Ns
Prescaler timer period should not be larger than 256 * 16 * clock cycle.
-
uint32_t tIdleTimeout_Ns
Idle timeout in unit of prescale time period.
-
uint32_t refreshPeriod_nsPerRow
Refresh timer period like 64ms * 1000000/8192 .
-
uint32_t refreshUrgThreshold
Refresh urgent threshold.
-
uint8_t refreshBurstLen
Refresh burst length.
-
uint8_t delayChain
Delay chain, which adds delays on DQS clock to compensate timings while DQS is faster than read data.
-
uint8_t autofreshTimes
Auto Refresh cycles times.
-
struct _semc_nand_timing_config
- #include <fsl_semc.h>
SEMC NAND device timing configuration structure.
Public Members
-
uint8_t tCeSetup_Ns
CE setup time: tCS.
-
uint8_t tCeHold_Ns
CE hold time: tCH.
-
uint8_t tCeInterval_Ns
CE interval time:tCEITV.
-
uint8_t tWeLow_Ns
WE low time: tWP.
-
uint8_t tWeHigh_Ns
WE high time: tWH.
-
uint8_t tReLow_Ns
RE low time: tRP.
-
uint8_t tReHigh_Ns
RE high time: tREH.
-
uint8_t tTurnAround_Ns
Turnaround time for async mode: tTA.
-
uint8_t tWehigh2Relow_Ns
WE# high to RE# wait time: tWHR.
-
uint8_t tRehigh2Welow_Ns
RE# high to WE# low wait time: tRHW.
-
uint8_t tAle2WriteStart_Ns
ALE to write start wait time: tADL.
-
uint8_t tReady2Relow_Ns
Ready to RE# low min wait time: tRR.
-
uint8_t tWehigh2Busy_Ns
WE# high to busy wait time: tWB.
-
uint8_t tCeSetup_Ns
-
struct _semc_nand_config
- #include <fsl_semc.h>
SEMC NAND configuration structure.
Public Members
-
semc_iomux_pin cePinMux
The CE pin mux setting. The kSEMC_MUXRDY is not valid for CE pin setting.
-
uint32_t axiAddress
The base address for AXI nand.
-
uint32_t axiMemsize_kbytes
The memory size in unit of kbytes for AXI nand.
-
uint32_t ipgAddress
The base address for IPG nand .
-
uint32_t ipgMemsize_kbytes
The memory size in unit of kbytes for IPG nand.
-
semc_rdy_polarity_t rdyactivePolarity
Wait ready polarity.
-
bool edoModeEnabled
EDO mode enabled.
-
semc_nand_column_bit_num_t columnAddrBitNum
Column address bit number.
-
semc_nand_address_option_t arrayAddrOption
Address option.
-
sem_nand_burst_len_t burstLen
Burst length.
-
smec_port_size_t portSize
Port size.
-
semc_nand_timing_config_t *timingConfig
SEMC nand timing configuration.
-
semc_iomux_pin cePinMux
-
struct _semc_nor_config
- #include <fsl_semc.h>
SEMC NOR configuration structure.
Public Members
-
semc_iomux_pin cePinMux
The CE# pin mux setting.
-
semc_iomux_nora27_pin addr27
The Addr bit 27 pin mux setting.
-
uint32_t address
The base address.
-
uint32_t memsize_kbytes
The memory size in unit of kbytes.
-
uint8_t addrPortWidth
The address port width.
-
semc_rdy_polarity_t rdyactivePolarity
Wait ready polarity.
-
semc_adv_polarity_t advActivePolarity
ADV# polarity.
-
semc_norsram_column_bit_num_t columnAddrBitNum
Column address bit number.
-
semc_addr_mode_t addrMode
Address mode.
-
sem_norsram_burst_len_t burstLen
Burst length.
-
smec_port_size_t portSize
Port size.
-
uint8_t tCeSetup_Ns
The CE setup time.
-
uint8_t tCeHold_Ns
The CE hold time.
-
uint8_t tCeInterval_Ns
CE interval minimum time.
-
uint8_t tAddrSetup_Ns
The address setup time.
-
uint8_t tAddrHold_Ns
The address hold time.
-
uint8_t tWeLow_Ns
WE low time for async mode.
-
uint8_t tWeHigh_Ns
WE high time for async mode.
-
uint8_t tReLow_Ns
RE low time for async mode.
-
uint8_t tReHigh_Ns
RE high time for async mode.
-
uint8_t tTurnAround_Ns
Turnaround time for async mode.
-
uint8_t tAddr2WriteHold_Ns
Address to write data hold time for async mode.
-
uint8_t tWriteSetup_Ns
Write data setup time for sync mode.
-
uint8_t tWriteHold_Ns
Write hold time for sync mode.
-
uint8_t latencyCount
Latency count for sync mode.
-
uint8_t readCycle
Read cycle time for sync mode.
-
uint8_t delayChain
Delay chain, which adds delays on DQS clock to compensate timings while DQS is faster than read data.
-
semc_iomux_pin cePinMux
-
struct _semc_sram_config
- #include <fsl_semc.h>
SEMC SRAM configuration structure.
Public Members
-
semc_iomux_pin cePinMux
The CE# pin mux setting.
-
semc_iomux_nora27_pin addr27
The Addr bit 27 pin mux setting.
-
uint32_t address
The base address.
-
uint32_t memsize_kbytes
The memory size in unit of kbytes.
-
uint8_t addrPortWidth
The address port width.
-
semc_adv_polarity_t advActivePolarity
ADV# polarity 1: active high, 0: active low.
-
semc_addr_mode_t addrMode
Address mode.
-
sem_norsram_burst_len_t burstLen
Burst length.
-
smec_port_size_t portSize
Port size.
-
semc_sync_mode_t syncMode
Sync mode.
-
bool waitEnable
Wait enable.
-
uint8_t waitSample
Wait sample.
-
semc_adv_level_control_t advLevelCtrl
ADV# level control during address hold state, 1: low, 0: high.
-
uint8_t tCeSetup_Ns
The CE setup time.
-
uint8_t tCeHold_Ns
The CE hold time.
-
uint8_t tCeInterval_Ns
CE interval minimum time.
-
uint8_t readHoldTime_Ns
read hold time.
-
uint8_t tAddrSetup_Ns
The address setup time.
-
uint8_t tAddrHold_Ns
The address hold time.
-
uint8_t tWeLow_Ns
WE low time for async mode.
-
uint8_t tWeHigh_Ns
WE high time for async mode.
-
uint8_t tReLow_Ns
RE low time for async mode.
-
uint8_t tReHigh_Ns
RE high time for async mode.
-
uint8_t tTurnAround_Ns
Turnaround time for async mode.
-
uint8_t tAddr2WriteHold_Ns
Address to write data hold time for async mode.
-
uint8_t tWriteSetup_Ns
Write data setup time for sync mode.
-
uint8_t tWriteHold_Ns
Write hold time for sync mode.
-
uint8_t latencyCount
Latency count for sync mode.
-
uint8_t readCycle
Read cycle time for sync mode.
-
uint8_t delayChain
Delay chain, which adds delays on DQS clock to compensate timings while DQS is faster than read data.
-
semc_iomux_pin cePinMux
-
struct _semc_dbi_config
- #include <fsl_semc.h>
SEMC DBI configuration structure.
Public Members
-
semc_iomux_pin csxPinMux
The CE# pin mux.
-
uint32_t address
The base address.
-
uint32_t memsize_kbytes
The memory size in unit of 4kbytes.
-
semc_dbi_column_bit_num_t columnAddrBitNum
Column address bit number.
-
sem_dbi_burst_len_t burstLen
Burst length.
-
smec_port_size_t portSize
Port size.
-
uint8_t tCsxSetup_Ns
The CSX setup time.
-
uint8_t tCsxHold_Ns
The CSX hold time.
-
uint8_t tWexLow_Ns
WEX low time.
-
uint8_t tWexHigh_Ns
WEX high time.
-
uint8_t tRdxLow_Ns
RDX low time.
-
uint8_t tRdxHigh_Ns
RDX high time.
-
uint8_t tCsxInterval_Ns
Write data setup time.
-
semc_iomux_pin csxPinMux
-
struct _semc_queuea_weight_struct
- #include <fsl_semc.h>
SEMC AXI queue a weight setting structure.
Public Members
-
uint32_t qos
weight of qos for queue 0 .
-
uint32_t aging
weight of aging for queue 0.
-
uint32_t slaveHitNoswitch
weight of read/write no switch for queue 0 .
-
uint32_t slaveHitSwitch
weight of read/write switch for queue 0.
-
uint32_t qos
-
union _semc_queuea_weight
- #include <fsl_semc.h>
SEMC AXI queue a weight setting union.
Public Members
-
semc_queuea_weight_struct_t queueaConfig
Structure configuration for queueA.
-
uint32_t queueaValue
Configuration value for queueA which could directly write to the reg.
-
semc_queuea_weight_struct_t queueaConfig
-
struct _semc_queueb_weight_struct
- #include <fsl_semc.h>
SEMC AXI queue b weight setting structure.
Public Members
-
uint32_t qos
weight of qos for queue 1.
-
uint32_t aging
weight of aging for queue 1.
-
uint32_t weightPagehit
weight of page hit for queue 1 only .
-
uint32_t slaveHitNoswitch
weight of read/write no switch for queue 1.
-
uint32_t bankRotation
weight of bank rotation for queue 1 only .
-
uint32_t qos
-
union _semc_queueb_weight
- #include <fsl_semc.h>
SEMC AXI queue b weight setting union.
Public Members
-
semc_queueb_weight_struct_t queuebConfig
Structure configuration for queueB.
-
uint32_t queuebValue
Configuration value for queueB which could directly write to the reg.
-
semc_queueb_weight_struct_t queuebConfig
-
struct _semc_axi_queueweight
- #include <fsl_semc.h>
SEMC AXI queue weight setting.
Public Members
-
bool queueaEnable
Enable queue a.
-
semc_queuea_weight_t queueaWeight
Weight settings for queue a.
-
bool queuebEnable
Enable queue b.
-
semc_queueb_weight_t queuebWeight
Weight settings for queue b.
-
bool queueaEnable
-
struct _semc_config_t
- #include <fsl_semc.h>
SEMC configuration structure.
busTimeoutCycles: when busTimeoutCycles is zero, the bus timeout cycle is 255*1024. otherwise the bus timeout cycles is busTimeoutCycles*1024. cmdTimeoutCycles: is used for command execution timeout cycles. it’s similar to the busTimeoutCycles.
Public Members
-
semc_dqs_mode_t dqsMode
Dummy read strobe mode: use enum in “semc_dqs_mode_t”.
-
uint8_t cmdTimeoutCycles
Command execution timeout cycles.
-
uint8_t busTimeoutCycles
Bus timeout cycles.
-
semc_axi_queueweight_t queueWeight
AXI queue weight.
-
semc_dqs_mode_t dqsMode
SNVS: Secure Non-Volatile Storage
Secure Non-Volatile Storage High-Power
-
void SNVS_HP_Init(SNVS_Type *base)
Initialize the SNVS.
Note
This API should be called at the beginning of the application using the SNVS driver.
- Parameters:
base – SNVS peripheral base address
-
void SNVS_HP_Deinit(SNVS_Type *base)
Deinitialize the SNVS.
- Parameters:
base – SNVS peripheral base address
-
void SNVS_HP_RTC_Init(SNVS_Type *base, const snvs_hp_rtc_config_t *config)
Ungates the SNVS clock and configures the peripheral for basic operation.
Note
This API should be called at the beginning of the application using the SNVS driver.
- Parameters:
base – SNVS peripheral base address
config – Pointer to the user’s SNVS configuration structure.
-
void SNVS_HP_RTC_Deinit(SNVS_Type *base)
Stops the RTC and SRTC timers.
- Parameters:
base – SNVS peripheral base address
-
void SNVS_HP_RTC_GetDefaultConfig(snvs_hp_rtc_config_t *config)
Fills in the SNVS config struct with the default settings.
The default values are as follows.
config->rtccalenable = false; config->rtccalvalue = 0U; config->PIFreq = 0U;
- Parameters:
config – Pointer to the user’s SNVS configuration structure.
-
status_t SNVS_HP_RTC_SetDatetime(SNVS_Type *base, const snvs_hp_rtc_datetime_t *datetime)
Sets the SNVS RTC date and time according to the given time structure.
- Parameters:
base – SNVS peripheral base address
datetime – Pointer to the structure where the date and time details are stored.
- Returns:
kStatus_Success: Success in setting the time and starting the SNVS RTC kStatus_InvalidArgument: Error because the datetime format is incorrect
-
void SNVS_HP_RTC_GetDatetime(SNVS_Type *base, snvs_hp_rtc_datetime_t *datetime)
Gets the SNVS RTC time and stores it in the given time structure.
- Parameters:
base – SNVS peripheral base address
datetime – Pointer to the structure where the date and time details are stored.
-
status_t SNVS_HP_RTC_SetAlarm(SNVS_Type *base, const snvs_hp_rtc_datetime_t *alarmTime)
Sets the SNVS RTC alarm time.
The function sets the RTC alarm. It also checks whether the specified alarm time is greater than the present time. If not, the function does not set the alarm and returns an error.
- Parameters:
base – SNVS peripheral base address
alarmTime – Pointer to the structure where the alarm time is stored.
- Returns:
kStatus_Success: success in setting the SNVS RTC alarm kStatus_InvalidArgument: Error because the alarm datetime format is incorrect kStatus_Fail: Error because the alarm time has already passed
-
void SNVS_HP_RTC_GetAlarm(SNVS_Type *base, snvs_hp_rtc_datetime_t *datetime)
Returns the SNVS RTC alarm time.
- Parameters:
base – SNVS peripheral base address
datetime – Pointer to the structure where the alarm date and time details are stored.
-
void SNVS_HP_RTC_TimeSynchronize(SNVS_Type *base)
The function synchronizes RTC counter value with SRTC.
- Parameters:
base – SNVS peripheral base address
-
static inline void SNVS_HP_RTC_EnableInterrupts(SNVS_Type *base, uint32_t mask)
Enables the selected SNVS interrupts.
- Parameters:
base – SNVS peripheral base address
mask – The interrupts to enable. This is a logical OR of members of the enumeration :: _snvs_hp_interrupts_t
-
static inline void SNVS_HP_RTC_DisableInterrupts(SNVS_Type *base, uint32_t mask)
Disables the selected SNVS interrupts.
- Parameters:
base – SNVS peripheral base address
mask – The interrupts to disable. This is a logical OR of members of the enumeration :: _snvs_hp_interrupts_t
-
uint32_t SNVS_HP_RTC_GetEnabledInterrupts(SNVS_Type *base)
Gets the enabled SNVS interrupts.
- Parameters:
base – SNVS peripheral base address
- Returns:
The enabled interrupts. This is the logical OR of members of the enumeration :: _snvs_hp_interrupts_t
-
uint32_t SNVS_HP_RTC_GetStatusFlags(SNVS_Type *base)
Gets the SNVS status flags.
- Parameters:
base – SNVS peripheral base address
- Returns:
The status flags. This is the logical OR of members of the enumeration :: _snvs_hp_status_flags_t
-
static inline void SNVS_HP_RTC_ClearStatusFlags(SNVS_Type *base, uint32_t mask)
Clears the SNVS status flags.
- Parameters:
base – SNVS peripheral base address
mask – The status flags to clear. This is a logical OR of members of the enumeration :: _snvs_hp_status_flags_t
-
static inline void SNVS_HP_RTC_StartTimer(SNVS_Type *base)
Starts the SNVS RTC time counter.
- Parameters:
base – SNVS peripheral base address
-
static inline void SNVS_HP_RTC_StopTimer(SNVS_Type *base)
Stops the SNVS RTC time counter.
- Parameters:
base – SNVS peripheral base address
-
static inline void SNVS_HP_EnableHighAssuranceCounter(SNVS_Type *base, bool enable)
Enable or disable the High Assurance Counter (HAC)
- Parameters:
base – SNVS peripheral base address
enable – Pass true to enable, false to disable.
-
static inline void SNVS_HP_StartHighAssuranceCounter(SNVS_Type *base, bool start)
Start or stop the High Assurance Counter (HAC)
- Parameters:
base – SNVS peripheral base address
start – Pass true to start, false to stop.
-
static inline void SNVS_HP_SetHighAssuranceCounterInitialValue(SNVS_Type *base, uint32_t value)
Set the High Assurance Counter (HAC) initialize value.
- Parameters:
base – SNVS peripheral base address
value – The initial value to set.
-
static inline void SNVS_HP_LoadHighAssuranceCounter(SNVS_Type *base)
Load the High Assurance Counter (HAC)
This function loads the HAC initialize value to counter register.
- Parameters:
base – SNVS peripheral base address
-
static inline uint32_t SNVS_HP_GetHighAssuranceCounter(SNVS_Type *base)
Get the current High Assurance Counter (HAC) value.
- Parameters:
base – SNVS peripheral base address
- Returns:
HAC currnet value.
-
static inline void SNVS_HP_ClearHighAssuranceCounter(SNVS_Type *base)
Clear the High Assurance Counter (HAC)
This function can be called in a functional or soft fail state. When the HAC is enabled:
If the HAC is cleared in the soft fail state, the SSM transitions to the hard fail state immediately;
If the HAC is cleared in functional state, the SSM will transition to hard fail immediately after transitioning to soft fail.
- Parameters:
base – SNVS peripheral base address
-
static inline void SNVS_HP_LockHighAssuranceCounter(SNVS_Type *base)
Lock the High Assurance Counter (HAC)
Once locked, the HAC initialize value could not be changed, the HAC enable status could not be changed. This could only be unlocked by system reset.
- Parameters:
base – SNVS peripheral base address
-
FSL_SNVS_HP_DRIVER_VERSION
Version 2.3.2
-
enum _snvs_hp_interrupts
List of SNVS interrupts.
Values:
-
enumerator kSNVS_RTC_AlarmInterrupt
RTC time alarm
-
enumerator kSNVS_RTC_PeriodicInterrupt
RTC periodic interrupt
-
enumerator kSNVS_RTC_AlarmInterrupt
-
enum _snvs_hp_status_flags
List of SNVS flags.
Values:
-
enumerator kSNVS_RTC_AlarmInterruptFlag
RTC time alarm flag
-
enumerator kSNVS_RTC_PeriodicInterruptFlag
RTC periodic interrupt flag
-
enumerator kSNVS_ZMK_ZeroFlag
The ZMK is zero
-
enumerator kSNVS_OTPMK_ZeroFlag
The OTPMK is zero
-
enumerator kSNVS_RTC_AlarmInterruptFlag
-
enum _snvs_hp_sv_status_flags
List of SNVS security violation flags.
Values:
-
enumerator kSNVS_LP_ViolationFlag
Low Power section Security Violation
-
enumerator kSNVS_ZMK_EccFailFlag
Zeroizable Master Key Error Correcting Code Check Failure
-
enumerator kSNVS_LP_SoftwareViolationFlag
LP Software Security Violation
-
enumerator kSNVS_FatalSoftwareViolationFlag
Software Fatal Security Violation
-
enumerator kSNVS_SoftwareViolationFlag
Software Security Violation
-
enumerator kSNVS_Violation0Flag
Security Violation 0
-
enumerator kSNVS_Violation1Flag
Security Violation 1
-
enumerator kSNVS_Violation2Flag
Security Violation 2
-
enumerator kSNVS_Violation4Flag
Security Violation 4
-
enumerator kSNVS_Violation5Flag
Security Violation 5
-
enumerator kSNVS_LP_ViolationFlag
-
enum _snvs_hp_ssm_state
List of SNVS Security State Machine State.
Values:
-
enumerator kSNVS_SSMInit
Init
-
enumerator kSNVS_SSMHardFail
Hard Fail
-
enumerator kSNVS_SSMSoftFail
Soft Fail
-
enumerator kSNVS_SSMInitInter
Init Intermediate (transition state between Init and Check)
-
enumerator kSNVS_SSMCheck
Check
-
enumerator kSNVS_SSMNonSecure
Non-Secure
-
enumerator kSNVS_SSMTrusted
Trusted
-
enumerator kSNVS_SSMSecure
Secure
-
enumerator kSNVS_SSMInit
-
typedef enum _snvs_hp_interrupts snvs_hp_interrupts_t
List of SNVS interrupts.
-
typedef enum _snvs_hp_status_flags snvs_hp_status_flags_t
List of SNVS flags.
-
typedef enum _snvs_hp_sv_status_flags snvs_hp_sv_status_flags_t
List of SNVS security violation flags.
-
typedef struct _snvs_hp_rtc_datetime snvs_hp_rtc_datetime_t
Structure is used to hold the date and time.
-
typedef struct _snvs_hp_rtc_config snvs_hp_rtc_config_t
SNVS config structure.
This structure holds the configuration settings for the SNVS peripheral. To initialize this structure to reasonable defaults, call the SNVS_GetDefaultConfig() function and pass a pointer to your config structure instance.
The config struct can be made const so it resides in flash
-
typedef enum _snvs_hp_ssm_state snvs_hp_ssm_state_t
List of SNVS Security State Machine State.
-
static inline void SNVS_HP_EnableMasterKeySelection(SNVS_Type *base, bool enable)
Enable or disable master key selection.
- Parameters:
base – SNVS peripheral base address
enable – Pass true to enable, false to disable.
-
static inline void SNVS_HP_ProgramZeroizableMasterKey(SNVS_Type *base)
Trigger to program Zeroizable Master Key.
- Parameters:
base – SNVS peripheral base address
-
static inline void SNVS_HP_ChangeSSMState(SNVS_Type *base)
Trigger SSM State Transition.
Trigger state transition of the system security monitor (SSM). It results only the following transitions of the SSM:
Check State -> Non-Secure (when Non-Secure Boot and not in Fab Configuration)
Check State –> Trusted (when Secure Boot or in Fab Configuration )
Trusted State –> Secure
Secure State –> Trusted
Soft Fail –> Non-Secure
- Parameters:
base – SNVS peripheral base address
-
static inline void SNVS_HP_SetSoftwareFatalSecurityViolation(SNVS_Type *base)
Trigger Software Fatal Security Violation.
The result SSM state transition is:
Check State -> Soft Fail
Non-Secure State -> Soft Fail
Trusted State -> Soft Fail
Secure State -> Soft Fail
- Parameters:
base – SNVS peripheral base address
-
static inline void SNVS_HP_SetSoftwareSecurityViolation(SNVS_Type *base)
Trigger Software Security Violation.
The result SSM state transition is:
Check -> Non-Secure
Trusted -> Soft Fail
Secure -> Soft Fail
- Parameters:
base – SNVS peripheral base address
-
static inline snvs_hp_ssm_state_t SNVS_HP_GetSSMState(SNVS_Type *base)
Get current SSM State.
- Parameters:
base – SNVS peripheral base address
- Returns:
Current SSM state
-
static inline void SNVS_HP_ResetLP(SNVS_Type *base)
Reset the SNVS LP section.
Reset the LP section except SRTC and Time alarm.
- Parameters:
base – SNVS peripheral base address
-
static inline uint32_t SNVS_HP_GetStatusFlags(SNVS_Type *base)
Get the SNVS HP status flags.
The flags are returned as the OR’ed value f the enumeration :: _snvs_hp_status_flags_t.
- Parameters:
base – SNVS peripheral base address
- Returns:
The OR’ed value of status flags.
-
static inline void SNVS_HP_ClearStatusFlags(SNVS_Type *base, uint32_t mask)
Clear the SNVS HP status flags.
The flags to clear are passed in as the OR’ed value of the enumeration :: _snvs_hp_status_flags_t. Only these flags could be cleared using this API.
kSNVS_RTC_PeriodicInterruptFlag
kSNVS_RTC_AlarmInterruptFlag
- Parameters:
base – SNVS peripheral base address
mask – OR’ed value of the flags to clear.
-
static inline uint32_t SNVS_HP_GetSecurityViolationStatusFlags(SNVS_Type *base)
Get the SNVS HP security violation status flags.
The flags are returned as the OR’ed value of the enumeration :: _snvs_hp_sv_status_flags_t.
- Parameters:
base – SNVS peripheral base address
- Returns:
The OR’ed value of security violation status flags.
-
static inline void SNVS_HP_ClearSecurityViolationStatusFlags(SNVS_Type *base, uint32_t mask)
Clear the SNVS HP security violation status flags.
The flags to clear are passed in as the OR’ed value of the enumeration :: _snvs_hp_sv_status_flags_t. Only these flags could be cleared using this API.
kSNVS_ZMK_EccFailFlag
kSNVS_Violation0Flag
kSNVS_Violation1Flag
kSNVS_Violation2Flag
kSNVS_Violation3Flag
kSNVS_Violation4Flag
kSNVS_Violation5Flag
- Parameters:
base – SNVS peripheral base address
mask – OR’ed value of the flags to clear.
-
SNVS_HPSVSR_SV0_MASK
-
SNVS_HPSVSR_SV1_MASK
-
SNVS_HPSVSR_SV2_MASK
-
SNVS_HPSVSR_SV4_MASK
-
SNVS_HPSVSR_SV5_MASK
-
SNVS_MAKE_HP_SV_FLAG(x)
Macro to make security violation flag.
Macro help to make security violation flag kSNVS_Violation0Flag to kSNVS_Violation5Flag, For example, SNVS_MAKE_HP_SV_FLAG(0) is kSNVS_Violation0Flag.
-
struct _snvs_hp_rtc_datetime
- #include <fsl_snvs_hp.h>
Structure is used to hold the date and time.
Public Members
-
uint16_t year
Range from 1970 to 2099.
-
uint8_t month
Range from 1 to 12.
-
uint8_t day
Range from 1 to 31 (depending on month).
-
uint8_t hour
Range from 0 to 23.
-
uint8_t minute
Range from 0 to 59.
-
uint8_t second
Range from 0 to 59.
-
uint16_t year
-
struct _snvs_hp_rtc_config
- #include <fsl_snvs_hp.h>
SNVS config structure.
This structure holds the configuration settings for the SNVS peripheral. To initialize this structure to reasonable defaults, call the SNVS_GetDefaultConfig() function and pass a pointer to your config structure instance.
The config struct can be made const so it resides in flash
Public Members
-
bool rtcCalEnable
true: RTC calibration mechanism is enabled; false:No calibration is used
-
uint32_t rtcCalValue
Defines signed calibration value for nonsecure RTC; This is a 5-bit 2’s complement value, range from -16 to +15
-
uint32_t periodicInterruptFreq
Defines frequency of the periodic interrupt; Range from 0 to 15
-
bool rtcCalEnable
Secure Non-Volatile Storage Low-Power
-
void SNVS_LP_Init(SNVS_Type *base)
Ungates the SNVS clock and configures the peripheral for basic operation.
Note
This API should be called at the beginning of the application using the SNVS driver.
- Parameters:
base – SNVS peripheral base address
-
void SNVS_LP_Deinit(SNVS_Type *base)
Deinit the SNVS LP section.
- Parameters:
base – SNVS peripheral base address
-
status_t SNVS_LP_SRTC_SetDatetime(SNVS_Type *base, const snvs_lp_srtc_datetime_t *datetime)
Sets the SNVS SRTC date and time according to the given time structure.
- Parameters:
base – SNVS peripheral base address
datetime – Pointer to the structure where the date and time details are stored.
- Returns:
kStatus_Success: Success in setting the time and starting the SNVS SRTC kStatus_InvalidArgument: Error because the datetime format is incorrect
-
void SNVS_LP_SRTC_GetDatetime(SNVS_Type *base, snvs_lp_srtc_datetime_t *datetime)
Gets the SNVS SRTC time and stores it in the given time structure.
- Parameters:
base – SNVS peripheral base address
datetime – Pointer to the structure where the date and time details are stored.
-
status_t SNVS_LP_SRTC_SetAlarm(SNVS_Type *base, const snvs_lp_srtc_datetime_t *alarmTime)
Sets the SNVS SRTC alarm time.
The function sets the SRTC alarm. It also checks whether the specified alarm time is greater than the present time. If not, the function does not set the alarm and returns an error. Please note, that SRTC alarm has limited resolution because only 32 most significant bits of SRTC counter are compared to SRTC Alarm register. If the alarm time is beyond SRTC resolution, the function does not set the alarm and returns an error.
- Parameters:
base – SNVS peripheral base address
alarmTime – Pointer to the structure where the alarm time is stored.
- Returns:
kStatus_Success: success in setting the SNVS SRTC alarm kStatus_InvalidArgument: Error because the alarm datetime format is incorrect kStatus_Fail: Error because the alarm time has already passed or is beyond resolution
-
void SNVS_LP_SRTC_GetAlarm(SNVS_Type *base, snvs_lp_srtc_datetime_t *datetime)
Returns the SNVS SRTC alarm time.
- Parameters:
base – SNVS peripheral base address
datetime – Pointer to the structure where the alarm date and time details are stored.
-
static inline void SNVS_LP_SRTC_EnableInterrupts(SNVS_Type *base, uint32_t mask)
Enables the selected SNVS interrupts.
- Parameters:
base – SNVS peripheral base address
mask – The interrupts to enable. This is a logical OR of members of the enumeration :: _snvs_lp_srtc_interrupts
-
static inline void SNVS_LP_SRTC_DisableInterrupts(SNVS_Type *base, uint32_t mask)
Disables the selected SNVS interrupts.
- Parameters:
base – SNVS peripheral base address
mask – The interrupts to enable. This is a logical OR of members of the enumeration :: _snvs_lp_srtc_interrupts
-
uint32_t SNVS_LP_SRTC_GetEnabledInterrupts(SNVS_Type *base)
Gets the enabled SNVS interrupts.
- Parameters:
base – SNVS peripheral base address
- Returns:
The enabled interrupts. This is the logical OR of members of the enumeration :: _snvs_lp_srtc_interrupts
-
uint32_t SNVS_LP_SRTC_GetStatusFlags(SNVS_Type *base)
Gets the SNVS status flags.
- Parameters:
base – SNVS peripheral base address
- Returns:
The status flags. This is the logical OR of members of the enumeration :: _snvs_lp_srtc_status_flags
-
static inline void SNVS_LP_SRTC_ClearStatusFlags(SNVS_Type *base, uint32_t mask)
Clears the SNVS status flags.
- Parameters:
base – SNVS peripheral base address
mask – The status flags to clear. This is a logical OR of members of the enumeration :: _snvs_lp_srtc_status_flags
-
static inline void SNVS_LP_SRTC_StartTimer(SNVS_Type *base)
Starts the SNVS SRTC time counter.
- Parameters:
base – SNVS peripheral base address
-
static inline void SNVS_LP_SRTC_StopTimer(SNVS_Type *base)
Stops the SNVS SRTC time counter.
- Parameters:
base – SNVS peripheral base address
-
void SNVS_LP_EnablePassiveTamper(SNVS_Type *base, snvs_lp_external_tamper_t pin, snvs_lp_passive_tamper_t config)
Enables the specified SNVS external tamper.
- Parameters:
base – SNVS peripheral base address
pin – SNVS external tamper pin
config – Configuration structure of external passive tamper
-
status_t SNVS_LP_EnableTxActiveTamper(SNVS_Type *base, snvs_lp_active_tx_tamper_t pin, tamper_active_tx_config_t config)
Enable active tamper tx external pad.
- Parameters:
base – SNVS peripheral base address
pin – SNVS active tamper pin
config – Configuration structure of external active tamper
-
status_t SNVS_LP_EnableRxActiveTamper(SNVS_Type *base, snvs_lp_external_tamper_t rx, tamper_active_rx_config_t config)
Enable active tamper rx external pad.
- Parameters:
base – SNVS peripheral base address
rx – SNVS external RX tamper pin
config – SNVS RX tamper config structure
-
status_t SNVS_LP_SetVoltageTamper(SNVS_Type *base, bool enable)
Sets voltage tamper detect.
- Parameters:
base – SNVS peripheral base address
enable – True if enable false if disable
-
status_t SNVS_LP_SetTemperatureTamper(SNVS_Type *base, bool enable)
Sets temperature tamper detect.
- Parameters:
base – SNVS peripheral base address
enable – True if enable false if disable
-
status_t SNVS_LP_SetClockTamper(SNVS_Type *base, bool enable)
Sets clock tamper detect.
- Parameters:
base – SNVS peripheral base address
enable – True if enable false if disable
-
snvs_lp_external_tamper_status_t SNVS_LP_CheckVoltageTamper(SNVS_Type *base)
brief Check voltage tamper
param base SNVS peripheral base address
-
snvs_lp_external_tamper_status_t SNVS_LP_CheckTemperatureTamper(SNVS_Type *base)
Check temperature tamper.
- Parameters:
base – SNVS peripheral base address
-
snvs_lp_external_tamper_status_t SNVS_LP_CheckClockTamper(SNVS_Type *base)
brief Check clock tamper
param base SNVS peripheral base address
-
void SNVS_LP_TamperPinTx_GetDefaultConfig(tamper_active_tx_config_t *config)
Fills in the SNVS tamper pin config struct with the default settings.
The default values are as follows. code config->clock = kSNVS_ActiveTamper16HZ; config->seed = 0U; config->polynomial = 0U; endcode
- Parameters:
config – Pointer to the user’s SNVS configuration structure.
-
void SNVS_LP_TamperPinRx_GetDefaultConfig(tamper_active_rx_config_t *config)
brief Fills in the SNVS tamper pin config struct with the default settings.
The default values are as follows. code config->filterenable = 0U; config->filter = 0U; config->tx = kSNVS_ActiveTamper1; endcode param config Pointer to the user’s SNVS configuration structure.
-
void SNVS_LP_PassiveTamperPin_GetDefaultConfig(snvs_lp_passive_tamper_t *config)
Fills in the SNVS tamper pin config struct with the default settings.
The default values are as follows. code config->polarity = 0U; config->filterenable = 0U; if available on SoC config->filter = 0U; if available on SoC endcode
- Parameters:
config – Pointer to the user’s SNVS configuration structure.
-
void SNVS_LP_DisableExternalTamper(SNVS_Type *base, snvs_lp_external_tamper_t pin)
Disables the specified SNVS external tamper.
- Parameters:
base – SNVS peripheral base address
pin – SNVS external tamper pin
-
void SNVS_LP_DisableAllExternalTamper(SNVS_Type *base)
Disable all external tamper.
- Parameters:
base – SNVS peripheral base address
-
snvs_lp_external_tamper_status_t SNVS_LP_GetExternalTamperStatus(SNVS_Type *base, snvs_lp_external_tamper_t pin)
Returns status of the specified external tamper.
- Parameters:
base – SNVS peripheral base address
pin – SNVS external tamper pin
- Returns:
The status flag. This is the enumeration :: _snvs_lp_external_tamper_status
-
void SNVS_LP_ClearExternalTamperStatus(SNVS_Type *base, snvs_lp_external_tamper_t pin)
Clears status of the specified external tamper.
- Parameters:
base – SNVS peripheral base address
pin – SNVS external tamper pin
-
void SNVS_LP_ClearAllExternalTamperStatus(SNVS_Type *base)
Clears status of the all external tamper.
- Parameters:
base – SNVS peripheral base address
-
static inline void SNVS_LP_EnableMonotonicCounter(SNVS_Type *base, bool enable)
Enable or disable the Monotonic Counter.
- Parameters:
base – SNVS peripheral base address
enable – Pass true to enable, false to disable.
-
uint64_t SNVS_LP_GetMonotonicCounter(SNVS_Type *base)
Get the current Monotonic Counter.
- Parameters:
base – SNVS peripheral base address
- Returns:
Current Monotonic Counter value.
-
static inline void SNVS_LP_IncreaseMonotonicCounter(SNVS_Type *base)
Increase the Monotonic Counter.
Increase the Monotonic Counter by 1.
- Parameters:
base – SNVS peripheral base address
-
void SNVS_LP_WriteZeroizableMasterKey(SNVS_Type *base, uint32_t ZMKey[8U])
Write Zeroizable Master Key (ZMK) to the SNVS registers.
- Parameters:
base – SNVS peripheral base address
ZMKey – The ZMK write to the SNVS register.
-
static inline void SNVS_LP_SetZeroizableMasterKeyValid(SNVS_Type *base, bool valid)
Set Zeroizable Master Key valid.
This API could only be called when using software programming mode. After writing ZMK using SNVS_LP_WriteZeroizableMasterKey, call this API to make the ZMK valid.
- Parameters:
base – SNVS peripheral base address
valid – Pass true to set valid, false to set invalid.
-
static inline bool SNVS_LP_GetZeroizableMasterKeyValid(SNVS_Type *base)
Get Zeroizable Master Key valid status.
In hardware programming mode, call this API to check whether the ZMK is valid.
- Parameters:
base – SNVS peripheral base address
- Returns:
true if valid, false if invalid.
-
static inline void SNVS_LP_SetZeroizableMasterKeyProgramMode(SNVS_Type *base, snvs_lp_zmk_program_mode_t mode)
Set Zeroizable Master Key programming mode.
- Parameters:
base – SNVS peripheral base address
mode – ZMK programming mode.
-
static inline void SNVS_LP_EnableZeroizableMasterKeyECC(SNVS_Type *base, bool enable)
Enable or disable Zeroizable Master Key ECC.
- Parameters:
base – SNVS peripheral base address
enable – Pass true to enable, false to disable.
-
static inline void SNVS_LP_SetMasterKeyMode(SNVS_Type *base, snvs_lp_master_key_mode_t mode)
Set SNVS Master Key mode.
Note
When kSNVS_ZMK or kSNVS_CMK used, the SNVS_HP must be configured to enable the master key selection.
- Parameters:
base – SNVS peripheral base address
mode – Master Key mode.
-
FSL_SNVS_LP_DRIVER_VERSION
Version 2.4.6
-
enum _snvs_lp_srtc_interrupts
List of SNVS_LP interrupts.
Values:
-
enumerator kSNVS_SRTC_AlarmInterrupt
SRTC time alarm.
-
enumerator kSNVS_SRTC_AlarmInterrupt
-
enum _snvs_lp_srtc_status_flags
List of SNVS_LP flags.
Values:
-
enumerator kSNVS_SRTC_AlarmInterruptFlag
SRTC time alarm flag
-
enumerator kSNVS_SRTC_AlarmInterruptFlag
-
enum _snvs_lp_external_tamper
List of SNVS_LP external tampers.
Values:
-
enumerator kSNVS_ExternalTamper1
-
enumerator kSNVS_ExternalTamper1
-
enum _snvs_lp_active_tamper
List of SNVS_LP active tampers.
Values:
-
enumerator kSNVS_ActiveTamper1
-
enumerator kSNVS_ActiveTamper2
-
enumerator kSNVS_ActiveTamper3
-
enumerator kSNVS_ActiveTamper4
-
enumerator kSNVS_ActiveTamper5
-
enumerator kSNVS_ActiveTamper1
-
enum _snvs_lp_active_clock
List of SNVS_LP external tampers.
Values:
-
enumerator kSNVS_ActiveTamper16HZ
-
enumerator kSNVS_ActiveTamper8HZ
-
enumerator kSNVS_ActiveTamper4HZ
-
enumerator kSNVS_ActiveTamper2HZ
-
enumerator kSNVS_ActiveTamper16HZ
-
enum _snvs_lp_external_tamper_status
List of SNVS_LP external tampers status.
Values:
-
enumerator kSNVS_TamperNotDetected
-
enumerator kSNVS_TamperDetected
-
enumerator kSNVS_TamperNotDetected
-
enum _snvs_lp_external_tamper_polarity
SNVS_LP external tamper polarity.
Values:
-
enumerator kSNVS_ExternalTamperActiveLow
-
enumerator kSNVS_ExternalTamperActiveHigh
-
enumerator kSNVS_ExternalTamperActiveLow
-
enum _snvs_lp_zmk_program_mode
SNVS_LP Zeroizable Master Key programming mode.
Values:
-
enumerator kSNVS_ZMKSoftwareProgram
Software programming mode.
-
enumerator kSNVS_ZMKHardwareProgram
Hardware programming mode.
-
enumerator kSNVS_ZMKSoftwareProgram
-
enum _snvs_lp_master_key_mode
SNVS_LP Master Key mode.
Values:
-
enumerator kSNVS_OTPMK
One Time Programmable Master Key.
-
enumerator kSNVS_ZMK
Zeroizable Master Key.
-
enumerator kSNVS_CMK
Combined Master Key, it is XOR of OPTMK and ZMK.
-
enumerator kSNVS_OTPMK
-
typedef enum _snvs_lp_srtc_interrupts snvs_lp_srtc_interrupts_t
List of SNVS_LP interrupts.
-
typedef enum _snvs_lp_srtc_status_flags snvs_lp_srtc_status_flags_t
List of SNVS_LP flags.
-
typedef enum _snvs_lp_external_tamper snvs_lp_external_tamper_t
List of SNVS_LP external tampers.
-
typedef enum _snvs_lp_active_tamper snvs_lp_active_tx_tamper_t
List of SNVS_LP active tampers.
-
typedef enum _snvs_lp_active_clock snvs_lp_active_clock_t
List of SNVS_LP external tampers.
-
typedef enum _snvs_lp_external_tamper_status snvs_lp_external_tamper_status_t
List of SNVS_LP external tampers status.
-
typedef enum _snvs_lp_external_tamper_polarity snvs_lp_external_tamper_polarity_t
SNVS_LP external tamper polarity.
-
typedef struct _snvs_lp_srtc_datetime snvs_lp_srtc_datetime_t
Structure is used to hold the date and time.
-
typedef struct _snvs_lp_srtc_config snvs_lp_srtc_config_t
SNVS_LP config structure.
This structure holds the configuration settings for the SNVS_LP peripheral. To initialize this structure to reasonable defaults, call the SNVS_LP_GetDefaultConfig() function and pass a pointer to your config structure instance.
The config struct can be made const so it resides in flash
-
typedef enum _snvs_lp_zmk_program_mode snvs_lp_zmk_program_mode_t
SNVS_LP Zeroizable Master Key programming mode.
-
typedef enum _snvs_lp_master_key_mode snvs_lp_master_key_mode_t
SNVS_LP Master Key mode.
-
void SNVS_LP_SRTC_Init(SNVS_Type *base, const snvs_lp_srtc_config_t *config)
Ungates the SNVS clock and configures the peripheral for basic operation.
Note
This API should be called at the beginning of the application using the SNVS driver.
- Parameters:
base – SNVS peripheral base address
config – Pointer to the user’s SNVS configuration structure.
-
void SNVS_LP_SRTC_Deinit(SNVS_Type *base)
Stops the SRTC timer.
- Parameters:
base – SNVS peripheral base address
-
void SNVS_LP_SRTC_GetDefaultConfig(snvs_lp_srtc_config_t *config)
Fills in the SNVS_LP config struct with the default settings.
The default values are as follows.
config->srtccalenable = false; config->srtccalvalue = 0U;
- Parameters:
config – Pointer to the user’s SNVS configuration structure.
-
SNVS_ZMK_REG_COUNT
Define of SNVS_LP Zeroizable Master Key registers.
-
SNVS_LP_MAX_TAMPER
Define of SNVS_LP Max possible tamper.
-
struct tamper_active_tx_config_t
- #include <fsl_snvs_lp.h>
Structure is used to configure SNVS LP active TX tamper pins.
-
struct tamper_active_rx_config_t
- #include <fsl_snvs_lp.h>
Structure is used to configure SNVS LP active RX tamper pins.
-
struct snvs_lp_passive_tamper_t
- #include <fsl_snvs_lp.h>
Structure is used to configure SNVS LP passive tamper pins.
-
struct _snvs_lp_srtc_datetime
- #include <fsl_snvs_lp.h>
Structure is used to hold the date and time.
Public Members
-
uint16_t year
Range from 1970 to 2099.
-
uint8_t month
Range from 1 to 12.
-
uint8_t day
Range from 1 to 31 (depending on month).
-
uint8_t hour
Range from 0 to 23.
-
uint8_t minute
Range from 0 to 59.
-
uint8_t second
Range from 0 to 59.
-
uint16_t year
-
struct _snvs_lp_srtc_config
- #include <fsl_snvs_lp.h>
SNVS_LP config structure.
This structure holds the configuration settings for the SNVS_LP peripheral. To initialize this structure to reasonable defaults, call the SNVS_LP_GetDefaultConfig() function and pass a pointer to your config structure instance.
The config struct can be made const so it resides in flash
Public Members
-
bool srtcCalEnable
true: SRTC calibration mechanism is enabled; false: No calibration is used
-
uint32_t srtcCalValue
Defines signed calibration value for SRTC; This is a 5-bit 2’s complement value, range from -16 to +15
-
bool srtcCalEnable
SPDIF: Sony/Philips Digital Interface
-
void SPDIF_Init(SPDIF_Type *base, const spdif_config_t *config)
Initializes the SPDIF peripheral.
Ungates the SPDIF clock, resets the module, and configures SPDIF with a configuration structure. The configuration structure can be custom filled or set with default values by SPDIF_GetDefaultConfig().
Note
This API should be called at the beginning of the application to use the SPDIF driver. Otherwise, accessing the SPDIF module can cause a hard fault because the clock is not enabled.
- Parameters:
base – SPDIF base pointer
config – SPDIF configuration structure.
-
void SPDIF_GetDefaultConfig(spdif_config_t *config)
Sets the SPDIF configuration structure to default values.
This API initializes the configuration structure for use in SPDIF_Init. The initialized structure can remain unchanged in SPDIF_Init, or it can be modified before calling SPDIF_Init. This is an example.
spdif_config_t config; SPDIF_GetDefaultConfig(&config);
- Parameters:
config – pointer to master configuration structure
-
void SPDIF_Deinit(SPDIF_Type *base)
De-initializes the SPDIF peripheral.
This API gates the SPDIF clock. The SPDIF module can’t operate unless SPDIF_Init is called to enable the clock.
- Parameters:
base – SPDIF base pointer
-
uint32_t SPDIF_GetInstance(SPDIF_Type *base)
Get the instance number for SPDIF.
- Parameters:
base – SPDIF base pointer.
-
static inline void SPDIF_TxFIFOReset(SPDIF_Type *base)
Resets the SPDIF Tx.
This function makes Tx FIFO in reset mode.
- Parameters:
base – SPDIF base pointer
-
static inline void SPDIF_RxFIFOReset(SPDIF_Type *base)
Resets the SPDIF Rx.
This function enables the software reset and FIFO reset of SPDIF Rx. After reset, clear the reset bit.
- Parameters:
base – SPDIF base pointer
-
void SPDIF_TxEnable(SPDIF_Type *base, bool enable)
Enables/disables the SPDIF Tx.
- Parameters:
base – SPDIF base pointer
enable – True means enable SPDIF Tx, false means disable.
-
static inline void SPDIF_RxEnable(SPDIF_Type *base, bool enable)
Enables/disables the SPDIF Rx.
- Parameters:
base – SPDIF base pointer
enable – True means enable SPDIF Rx, false means disable.
-
static inline uint32_t SPDIF_GetStatusFlag(SPDIF_Type *base)
Gets the SPDIF status flag state.
- Parameters:
base – SPDIF base pointer
- Returns:
SPDIF status flag value. Use the _spdif_interrupt_enable_t to get the status value needed.
-
static inline void SPDIF_ClearStatusFlags(SPDIF_Type *base, uint32_t mask)
Clears the SPDIF status flag state.
- Parameters:
base – SPDIF base pointer
mask – State mask. It can be a combination of the _spdif_interrupt_enable_t member. Notice these members cannot be included, as these flags cannot be cleared by writing 1 to these bits:
kSPDIF_UChannelReceiveRegisterFull
kSPDIF_QChannelReceiveRegisterFull
kSPDIF_TxFIFOEmpty
kSPDIF_RxFIFOFull
-
static inline void SPDIF_EnableInterrupts(SPDIF_Type *base, uint32_t mask)
Enables the SPDIF Tx interrupt requests.
- Parameters:
base – SPDIF base pointer
mask – interrupt source The parameter can be a combination of the following sources if defined.
kSPDIF_WordStartInterruptEnable
kSPDIF_SyncErrorInterruptEnable
kSPDIF_FIFOWarningInterruptEnable
kSPDIF_FIFORequestInterruptEnable
kSPDIF_FIFOErrorInterruptEnable
-
static inline void SPDIF_DisableInterrupts(SPDIF_Type *base, uint32_t mask)
Disables the SPDIF Tx interrupt requests.
- Parameters:
base – SPDIF base pointer
mask – interrupt source The parameter can be a combination of the following sources if defined.
kSPDIF_WordStartInterruptEnable
kSPDIF_SyncErrorInterruptEnable
kSPDIF_FIFOWarningInterruptEnable
kSPDIF_FIFORequestInterruptEnable
kSPDIF_FIFOErrorInterruptEnable
-
static inline void SPDIF_EnableDMA(SPDIF_Type *base, uint32_t mask, bool enable)
Enables/disables the SPDIF DMA requests.
- Parameters:
base – SPDIF base pointer
mask – SPDIF DMA enable mask, The parameter can be a combination of the following sources if defined
kSPDIF_RxDMAEnable
kSPDIF_TxDMAEnable
enable – True means enable DMA, false means disable DMA.
-
static inline uint32_t SPDIF_TxGetLeftDataRegisterAddress(SPDIF_Type *base)
Gets the SPDIF Tx left data register address.
This API is used to provide a transfer address for the SPDIF DMA transfer configuration.
- Parameters:
base – SPDIF base pointer.
- Returns:
data register address.
-
static inline uint32_t SPDIF_TxGetRightDataRegisterAddress(SPDIF_Type *base)
Gets the SPDIF Tx right data register address.
This API is used to provide a transfer address for the SPDIF DMA transfer configuration.
- Parameters:
base – SPDIF base pointer.
- Returns:
data register address.
-
static inline uint32_t SPDIF_RxGetLeftDataRegisterAddress(SPDIF_Type *base)
Gets the SPDIF Rx left data register address.
This API is used to provide a transfer address for the SPDIF DMA transfer configuration.
- Parameters:
base – SPDIF base pointer.
- Returns:
data register address.
-
static inline uint32_t SPDIF_RxGetRightDataRegisterAddress(SPDIF_Type *base)
Gets the SPDIF Rx right data register address.
This API is used to provide a transfer address for the SPDIF DMA transfer configuration.
- Parameters:
base – SPDIF base pointer.
- Returns:
data register address.
-
void SPDIF_TxSetSampleRate(SPDIF_Type *base, uint32_t sampleRate_Hz, uint32_t sourceClockFreq_Hz)
Configures the SPDIF Tx sample rate.
The audio format can be changed at run-time. This function configures the sample rate.
- Parameters:
base – SPDIF base pointer.
sampleRate_Hz – SPDIF sample rate frequency in Hz.
sourceClockFreq_Hz – SPDIF tx clock source frequency in Hz.
-
uint32_t SPDIF_GetRxSampleRate(SPDIF_Type *base, uint32_t clockSourceFreq_Hz)
Configures the SPDIF Rx audio format.
The audio format can be changed at run-time. This function configures the sample rate and audio data format to be transferred.
- Parameters:
base – SPDIF base pointer.
clockSourceFreq_Hz – SPDIF system clock frequency in hz.
-
void SPDIF_WriteBlocking(SPDIF_Type *base, uint8_t *buffer, uint32_t size)
Sends data using a blocking method.
Note
This function blocks by polling until data is ready to be sent.
- Parameters:
base – SPDIF base pointer.
buffer – Pointer to the data to be written.
size – Bytes to be written.
-
static inline void SPDIF_WriteLeftData(SPDIF_Type *base, uint32_t data)
Writes data into SPDIF FIFO.
- Parameters:
base – SPDIF base pointer.
data – Data needs to be written.
-
static inline void SPDIF_WriteRightData(SPDIF_Type *base, uint32_t data)
Writes data into SPDIF FIFO.
- Parameters:
base – SPDIF base pointer.
data – Data needs to be written.
-
static inline void SPDIF_WriteChannelStatusHigh(SPDIF_Type *base, uint32_t data)
Writes data into SPDIF FIFO.
- Parameters:
base – SPDIF base pointer.
data – Data needs to be written.
-
static inline void SPDIF_WriteChannelStatusLow(SPDIF_Type *base, uint32_t data)
Writes data into SPDIF FIFO.
- Parameters:
base – SPDIF base pointer.
data – Data needs to be written.
-
void SPDIF_ReadBlocking(SPDIF_Type *base, uint8_t *buffer, uint32_t size)
Receives data using a blocking method.
Note
This function blocks by polling until data is ready to be sent.
- Parameters:
base – SPDIF base pointer.
buffer – Pointer to the data to be read.
size – Bytes to be read.
-
static inline uint32_t SPDIF_ReadLeftData(SPDIF_Type *base)
Reads data from the SPDIF FIFO.
- Parameters:
base – SPDIF base pointer.
- Returns:
Data in SPDIF FIFO.
-
static inline uint32_t SPDIF_ReadRightData(SPDIF_Type *base)
Reads data from the SPDIF FIFO.
- Parameters:
base – SPDIF base pointer.
- Returns:
Data in SPDIF FIFO.
-
static inline uint32_t SPDIF_ReadChannelStatusHigh(SPDIF_Type *base)
Reads data from the SPDIF FIFO.
- Parameters:
base – SPDIF base pointer.
- Returns:
Data in SPDIF FIFO.
-
static inline uint32_t SPDIF_ReadChannelStatusLow(SPDIF_Type *base)
Reads data from the SPDIF FIFO.
- Parameters:
base – SPDIF base pointer.
- Returns:
Data in SPDIF FIFO.
-
static inline uint32_t SPDIF_ReadQChannel(SPDIF_Type *base)
Reads data from the SPDIF FIFO.
- Parameters:
base – SPDIF base pointer.
- Returns:
Data in SPDIF FIFO.
-
static inline uint32_t SPDIF_ReadUChannel(SPDIF_Type *base)
Reads data from the SPDIF FIFO.
- Parameters:
base – SPDIF base pointer.
- Returns:
Data in SPDIF FIFO.
-
void SPDIF_TransferTxCreateHandle(SPDIF_Type *base, spdif_handle_t *handle, spdif_transfer_callback_t callback, void *userData)
Initializes the SPDIF Tx handle.
This function initializes the Tx handle for the SPDIF Tx transactional APIs. Call this function once to get the handle initialized.
- Parameters:
base – SPDIF base pointer
handle – SPDIF handle pointer.
callback – Pointer to the user callback function.
userData – User parameter passed to the callback function
-
void SPDIF_TransferRxCreateHandle(SPDIF_Type *base, spdif_handle_t *handle, spdif_transfer_callback_t callback, void *userData)
Initializes the SPDIF Rx handle.
This function initializes the Rx handle for the SPDIF Rx transactional APIs. Call this function once to get the handle initialized.
- Parameters:
base – SPDIF base pointer.
handle – SPDIF handle pointer.
callback – Pointer to the user callback function.
userData – User parameter passed to the callback function.
-
status_t SPDIF_TransferSendNonBlocking(SPDIF_Type *base, spdif_handle_t *handle, spdif_transfer_t *xfer)
Performs an interrupt non-blocking send transfer on SPDIF.
Note
This API returns immediately after the transfer initiates. Call the SPDIF_TxGetTransferStatusIRQ to poll the transfer status and check whether the transfer is finished. If the return status is not kStatus_SPDIF_Busy, the transfer is finished.
- Parameters:
base – SPDIF base pointer.
handle – Pointer to the spdif_handle_t structure which stores the transfer state.
xfer – Pointer to the spdif_transfer_t structure.
- Return values:
kStatus_Success – Successfully started the data receive.
kStatus_SPDIF_TxBusy – Previous receive still not finished.
kStatus_InvalidArgument – The input parameter is invalid.
-
status_t SPDIF_TransferReceiveNonBlocking(SPDIF_Type *base, spdif_handle_t *handle, spdif_transfer_t *xfer)
Performs an interrupt non-blocking receive transfer on SPDIF.
Note
This API returns immediately after the transfer initiates. Call the SPDIF_RxGetTransferStatusIRQ to poll the transfer status and check whether the transfer is finished. If the return status is not kStatus_SPDIF_Busy, the transfer is finished.
- Parameters:
base – SPDIF base pointer
handle – Pointer to the spdif_handle_t structure which stores the transfer state.
xfer – Pointer to the spdif_transfer_t structure.
- Return values:
kStatus_Success – Successfully started the data receive.
kStatus_SPDIF_RxBusy – Previous receive still not finished.
kStatus_InvalidArgument – The input parameter is invalid.
-
status_t SPDIF_TransferGetSendCount(SPDIF_Type *base, spdif_handle_t *handle, size_t *count)
Gets a set byte count.
- Parameters:
base – SPDIF base pointer.
handle – Pointer to the spdif_handle_t structure which stores the transfer state.
count – Bytes count sent.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is not a non-blocking transaction currently in progress.
-
status_t SPDIF_TransferGetReceiveCount(SPDIF_Type *base, spdif_handle_t *handle, size_t *count)
Gets a received byte count.
- Parameters:
base – SPDIF base pointer.
handle – Pointer to the spdif_handle_t structure which stores the transfer state.
count – Bytes count received.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is not a non-blocking transaction currently in progress.
-
void SPDIF_TransferAbortSend(SPDIF_Type *base, spdif_handle_t *handle)
Aborts the current send.
Note
This API can be called any time when an interrupt non-blocking transfer initiates to abort the transfer early.
- Parameters:
base – SPDIF base pointer.
handle – Pointer to the spdif_handle_t structure which stores the transfer state.
-
void SPDIF_TransferAbortReceive(SPDIF_Type *base, spdif_handle_t *handle)
Aborts the current IRQ receive.
Note
This API can be called when an interrupt non-blocking transfer initiates to abort the transfer early.
- Parameters:
base – SPDIF base pointer
handle – Pointer to the spdif_handle_t structure which stores the transfer state.
-
void SPDIF_TransferTxHandleIRQ(SPDIF_Type *base, spdif_handle_t *handle)
Tx interrupt handler.
- Parameters:
base – SPDIF base pointer.
handle – Pointer to the spdif_handle_t structure.
-
void SPDIF_TransferRxHandleIRQ(SPDIF_Type *base, spdif_handle_t *handle)
Tx interrupt handler.
- Parameters:
base – SPDIF base pointer.
handle – Pointer to the spdif_handle_t structure.
-
FSL_SPDIF_DRIVER_VERSION
Version 2.0.7
SPDIF return status.
Values:
-
enumerator kStatus_SPDIF_RxDPLLLocked
SPDIF Rx PLL locked.
-
enumerator kStatus_SPDIF_TxFIFOError
SPDIF Tx FIFO error.
-
enumerator kStatus_SPDIF_TxFIFOResync
SPDIF Tx left and right FIFO resync.
-
enumerator kStatus_SPDIF_RxCnew
SPDIF Rx status channel value updated.
-
enumerator kStatus_SPDIF_ValidatyNoGood
SPDIF validaty flag not good.
-
enumerator kStatus_SPDIF_RxIllegalSymbol
SPDIF Rx receive illegal symbol.
-
enumerator kStatus_SPDIF_RxParityBitError
SPDIF Rx parity bit error.
-
enumerator kStatus_SPDIF_UChannelOverrun
SPDIF receive U channel overrun.
-
enumerator kStatus_SPDIF_QChannelOverrun
SPDIF receive Q channel overrun.
-
enumerator kStatus_SPDIF_UQChannelSync
SPDIF U/Q channel sync found.
-
enumerator kStatus_SPDIF_UQChannelFrameError
SPDIF U/Q channel frame error.
-
enumerator kStatus_SPDIF_RxFIFOError
SPDIF Rx FIFO error.
-
enumerator kStatus_SPDIF_RxFIFOResync
SPDIF Rx left and right FIFO resync.
-
enumerator kStatus_SPDIF_LockLoss
SPDIF Rx PLL clock lock loss.
-
enumerator kStatus_SPDIF_TxIdle
SPDIF Tx is idle
-
enumerator kStatus_SPDIF_RxIdle
SPDIF Rx is idle
-
enumerator kStatus_SPDIF_QueueFull
SPDIF queue full
-
enumerator kStatus_SPDIF_RxDPLLLocked
-
enum _spdif_rxfull_select
SPDIF Rx FIFO full falg select, it decides when assert the rx full flag.
Values:
-
enumerator kSPDIF_RxFull1Sample
Rx full at least 1 sample in left and right FIFO
-
enumerator kSPDIF_RxFull4Samples
Rx full at least 4 sample in left and right FIFO
-
enumerator kSPDIF_RxFull8Samples
Rx full at least 8 sample in left and right FIFO
-
enumerator kSPDIF_RxFull16Samples
Rx full at least 16 sample in left and right FIFO
-
enumerator kSPDIF_RxFull1Sample
-
enum _spdif_txempty_select
SPDIF tx FIFO EMPTY falg select, it decides when assert the tx empty flag.
Values:
-
enumerator kSPDIF_TxEmpty0Sample
Tx empty at most 0 sample in left and right FIFO
-
enumerator kSPDIF_TxEmpty4Samples
Tx empty at most 4 sample in left and right FIFO
-
enumerator kSPDIF_TxEmpty8Samples
Tx empty at most 8 sample in left and right FIFO
-
enumerator kSPDIF_TxEmpty12Samples
Tx empty at most 12 sample in left and right FIFO
-
enumerator kSPDIF_TxEmpty0Sample
-
enum _spdif_uchannel_source
SPDIF U channel source.
Values:
-
enumerator kSPDIF_NoUChannel
No embedded U channel
-
enumerator kSPDIF_UChannelFromRx
U channel from receiver, it is CD mode
-
enumerator kSPDIF_UChannelFromTx
U channel from on chip tx
-
enumerator kSPDIF_NoUChannel
-
enum _spdif_gain_select
SPDIF clock gain.
Values:
-
enumerator kSPDIF_GAIN_24
Gain select is 24
-
enumerator kSPDIF_GAIN_16
Gain select is 16
-
enumerator kSPDIF_GAIN_12
Gain select is 12
-
enumerator kSPDIF_GAIN_8
Gain select is 8
-
enumerator kSPDIF_GAIN_6
Gain select is 6
-
enumerator kSPDIF_GAIN_4
Gain select is 4
-
enumerator kSPDIF_GAIN_3
Gain select is 3
-
enumerator kSPDIF_GAIN_24
-
enum _spdif_tx_source
SPDIF tx data source.
Values:
-
enumerator kSPDIF_txFromReceiver
Tx data directly through SPDIF receiver
-
enumerator kSPDIF_txNormal
Normal operation, data from processor
-
enumerator kSPDIF_txFromReceiver
-
enum _spdif_validity_config
SPDIF tx data source.
Values:
-
enumerator kSPDIF_validityFlagAlwaysSet
Outgoing validity flags always set
-
enumerator kSPDIF_validityFlagAlwaysClear
Outgoing validity flags always clear
-
enumerator kSPDIF_validityFlagAlwaysSet
The SPDIF interrupt enable flag.
Values:
-
enumerator kSPDIF_RxDPLLLocked
SPDIF DPLL locked
-
enumerator kSPDIF_TxFIFOError
Tx FIFO underrun or overrun
-
enumerator kSPDIF_TxFIFOResync
Tx FIFO left and right channel resync
-
enumerator kSPDIF_RxControlChannelChange
SPDIF Rx control channel value changed
-
enumerator kSPDIF_ValidityFlagNoGood
SPDIF validity flag no good
-
enumerator kSPDIF_RxIllegalSymbol
SPDIF receiver found illegal symbol
-
enumerator kSPDIF_RxParityBitError
SPDIF receiver found parity bit error
-
enumerator kSPDIF_UChannelReceiveRegisterFull
SPDIF U channel revceive register full
-
enumerator kSPDIF_UChannelReceiveRegisterOverrun
SPDIF U channel receive register overrun
-
enumerator kSPDIF_QChannelReceiveRegisterFull
SPDIF Q channel receive reigster full
-
enumerator kSPDIF_QChannelReceiveRegisterOverrun
SPDIF Q channel receive register overrun
-
enumerator kSPDIF_UQChannelSync
SPDIF U/Q channel sync found
-
enumerator kSPDIF_UQChannelFrameError
SPDIF U/Q channel frame error
-
enumerator kSPDIF_RxFIFOError
SPDIF Rx FIFO underrun/overrun
-
enumerator kSPDIF_RxFIFOResync
SPDIF Rx left and right FIFO resync
-
enumerator kSPDIF_LockLoss
SPDIF receiver loss of lock
-
enumerator kSPDIF_TxFIFOEmpty
SPDIF Tx FIFO empty
-
enumerator kSPDIF_RxFIFOFull
SPDIF Rx FIFO full
-
enumerator kSPDIF_AllInterrupt
all interrupt
-
enumerator kSPDIF_RxDPLLLocked
The DMA request sources.
Values:
-
enumerator kSPDIF_RxDMAEnable
Rx FIFO full
-
enumerator kSPDIF_TxDMAEnable
Tx FIFO empty
-
enumerator kSPDIF_RxDMAEnable
-
typedef enum _spdif_rxfull_select spdif_rxfull_select_t
SPDIF Rx FIFO full falg select, it decides when assert the rx full flag.
-
typedef enum _spdif_txempty_select spdif_txempty_select_t
SPDIF tx FIFO EMPTY falg select, it decides when assert the tx empty flag.
-
typedef enum _spdif_uchannel_source spdif_uchannel_source_t
SPDIF U channel source.
-
typedef enum _spdif_gain_select spdif_gain_select_t
SPDIF clock gain.
-
typedef enum _spdif_tx_source spdif_tx_source_t
SPDIF tx data source.
-
typedef enum _spdif_validity_config spdif_validity_config_t
SPDIF tx data source.
-
typedef struct _spdif_config spdif_config_t
SPDIF user configuration structure.
-
typedef struct _spdif_transfer spdif_transfer_t
SPDIF transfer structure.
-
typedef struct _spdif_handle spdif_handle_t
-
typedef void (*spdif_transfer_callback_t)(SPDIF_Type *base, spdif_handle_t *handle, status_t status, void *userData)
SPDIF transfer callback prototype.
-
SPDIF_XFER_QUEUE_SIZE
SPDIF transfer queue size, user can refine it according to use case.
-
struct _spdif_config
- #include <fsl_spdif.h>
SPDIF user configuration structure.
Public Members
-
bool isTxAutoSync
If auto sync mechanism open
-
bool isRxAutoSync
If auto sync mechanism open
-
uint8_t DPLLClkSource
SPDIF DPLL clock source, range from 0~15, meaning is chip-specific
-
uint8_t txClkSource
SPDIF tx clock source, range from 0~7, meaning is chip-specific
-
spdif_rxfull_select_t rxFullSelect
SPDIF rx buffer full select
-
spdif_txempty_select_t txFullSelect
SPDIF tx buffer empty select
-
spdif_uchannel_source_t uChannelSrc
U channel source
-
spdif_tx_source_t txSource
SPDIF tx data source
-
spdif_validity_config_t validityConfig
Validity flag config
-
spdif_gain_select_t gain
Rx receive clock measure gain parameter.
-
bool isTxAutoSync
-
struct _spdif_transfer
- #include <fsl_spdif.h>
SPDIF transfer structure.
Public Members
-
uint8_t *data
Data start address to transfer.
-
uint8_t *qdata
Data buffer for Q channel
-
uint8_t *udata
Data buffer for C channel
-
size_t dataSize
Transfer size.
-
uint8_t *data
-
struct _spdif_handle
- #include <fsl_spdif.h>
SPDIF handle structure.
Public Members
-
uint32_t state
Transfer status
-
spdif_transfer_callback_t callback
Callback function called at transfer event
-
void *userData
Callback parameter passed to callback function
-
spdif_transfer_t spdifQueue[(4U)]
Transfer queue storing queued transfer
-
size_t transferSize[(4U)]
Data bytes need to transfer
-
volatile uint8_t queueUser
Index for user to queue transfer
-
volatile uint8_t queueDriver
Index for driver to get the transfer data and size
-
uint8_t watermark
Watermark value
-
uint32_t state
SPDIF eDMA Driver
-
void SPDIF_TransferTxCreateHandleEDMA(SPDIF_Type *base, spdif_edma_handle_t *handle, spdif_edma_callback_t callback, void *userData, edma_handle_t *dmaLeftHandle, edma_handle_t *dmaRightHandle)
Initializes the SPDIF eDMA handle.
This function initializes the SPDIF master DMA handle, which can be used for other SPDIF master transactional APIs. Usually, for a specified SPDIF instance, call this API once to get the initialized handle.
- Parameters:
base – SPDIF base pointer.
handle – SPDIF eDMA handle pointer.
callback – Pointer to user callback function.
userData – User parameter passed to the callback function.
dmaLeftHandle – eDMA handle pointer for left channel, this handle shall be static allocated by users.
dmaRightHandle – eDMA handle pointer for right channel, this handle shall be static allocated by users.
-
void SPDIF_TransferRxCreateHandleEDMA(SPDIF_Type *base, spdif_edma_handle_t *handle, spdif_edma_callback_t callback, void *userData, edma_handle_t *dmaLeftHandle, edma_handle_t *dmaRightHandle)
Initializes the SPDIF Rx eDMA handle.
This function initializes the SPDIF slave DMA handle, which can be used for other SPDIF master transactional APIs. Usually, for a specified SPDIF instance, call this API once to get the initialized handle.
- Parameters:
base – SPDIF base pointer.
handle – SPDIF eDMA handle pointer.
callback – Pointer to user callback function.
userData – User parameter passed to the callback function.
dmaLeftHandle – eDMA handle pointer for left channel, this handle shall be static allocated by users.
dmaRightHandle – eDMA handle pointer for right channel, this handle shall be static allocated by users.
-
status_t SPDIF_TransferSendEDMA(SPDIF_Type *base, spdif_edma_handle_t *handle, spdif_edma_transfer_t *xfer)
Performs a non-blocking SPDIF transfer using DMA.
Note
This interface returns immediately after the transfer initiates. Call SPDIF_GetTransferStatus to poll the transfer status and check whether the SPDIF transfer is finished.
- Parameters:
base – SPDIF base pointer.
handle – SPDIF eDMA handle pointer.
xfer – Pointer to the DMA transfer structure.
- Return values:
kStatus_Success – Start a SPDIF eDMA send successfully.
kStatus_InvalidArgument – The input argument is invalid.
kStatus_TxBusy – SPDIF is busy sending data.
-
status_t SPDIF_TransferReceiveEDMA(SPDIF_Type *base, spdif_edma_handle_t *handle, spdif_edma_transfer_t *xfer)
Performs a non-blocking SPDIF receive using eDMA.
Note
This interface returns immediately after the transfer initiates. Call the SPDIF_GetReceiveRemainingBytes to poll the transfer status and check whether the SPDIF transfer is finished.
- Parameters:
base – SPDIF base pointer
handle – SPDIF eDMA handle pointer.
xfer – Pointer to DMA transfer structure.
- Return values:
kStatus_Success – Start a SPDIF eDMA receive successfully.
kStatus_InvalidArgument – The input argument is invalid.
kStatus_RxBusy – SPDIF is busy receiving data.
-
void SPDIF_TransferAbortSendEDMA(SPDIF_Type *base, spdif_edma_handle_t *handle)
Aborts a SPDIF transfer using eDMA.
- Parameters:
base – SPDIF base pointer.
handle – SPDIF eDMA handle pointer.
-
void SPDIF_TransferAbortReceiveEDMA(SPDIF_Type *base, spdif_edma_handle_t *handle)
Aborts a SPDIF receive using eDMA.
- Parameters:
base – SPDIF base pointer
handle – SPDIF eDMA handle pointer.
-
status_t SPDIF_TransferGetSendCountEDMA(SPDIF_Type *base, spdif_edma_handle_t *handle, size_t *count)
Gets byte count sent by SPDIF.
- Parameters:
base – SPDIF base pointer.
handle – SPDIF eDMA handle pointer.
count – Bytes count sent by SPDIF.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is no non-blocking transaction in progress.
-
status_t SPDIF_TransferGetReceiveCountEDMA(SPDIF_Type *base, spdif_edma_handle_t *handle, size_t *count)
Gets byte count received by SPDIF.
- Parameters:
base – SPDIF base pointer
handle – SPDIF eDMA handle pointer.
count – Bytes count received by SPDIF.
- Return values:
kStatus_Success – Succeed get the transfer count.
kStatus_NoTransferInProgress – There is no non-blocking transaction in progress.
-
FSL_SPDIF_EDMA_DRIVER_VERSION
Version 2.0.8
-
typedef struct _spdif_edma_handle spdif_edma_handle_t
-
typedef void (*spdif_edma_callback_t)(SPDIF_Type *base, spdif_edma_handle_t *handle, status_t status, void *userData)
SPDIF eDMA transfer callback function for finish and error.
-
typedef struct _spdif_edma_transfer spdif_edma_transfer_t
SPDIF transfer structure.
-
struct _spdif_edma_transfer
- #include <fsl_spdif_edma.h>
SPDIF transfer structure.
Public Members
-
uint8_t *leftData
Data start address to transfer.
-
uint8_t *rightData
Data start address to transfer.
-
size_t dataSize
Transfer size.
-
uint8_t *leftData
-
struct _spdif_edma_handle
- #include <fsl_spdif_edma.h>
SPDIF DMA transfer handle, users should not touch the content of the handle.
Public Members
-
edma_handle_t *dmaLeftHandle
DMA handler for SPDIF left channel
-
edma_handle_t *dmaRightHandle
DMA handler for SPDIF right channel
-
uint8_t nbytes
eDMA minor byte transfer count initially configured.
-
uint8_t count
The transfer data count in a DMA request
-
uint32_t state
Internal state for SPDIF eDMA transfer
-
spdif_edma_callback_t callback
Callback for users while transfer finish or error occurs
-
void *userData
User callback parameter
-
edma_tcd_t leftTcd[(4U) + 1U]
TCD pool for eDMA transfer.
-
edma_tcd_t rightTcd[(4U) + 1U]
TCD pool for eDMA transfer.
-
spdif_edma_transfer_t spdifQueue[(4U)]
Transfer queue storing queued transfer.
-
size_t transferSize[(4U)]
Data bytes need to transfer, left and right are the same, so use one
-
volatile uint8_t queueUser
Index for user to queue transfer.
-
volatile uint8_t queueDriver
Index for driver to get the transfer data and size
-
edma_handle_t *dmaLeftHandle
SRC: System Reset Controller Driver
-
FSL_SRC_DRIVER_VERSION
SRC driver version 2.0.1.
-
enum _src_reset_status_flags
SRC reset status flags.
Values:
-
enumerator kSRC_ResetOutputEnableFlag
This bit indicates if RESET status is driven out on PTE0 pin.
-
enumerator kSRC_TemperatureSensorResetFlag
Indicates whether the reset was the result of software reset from on-chip Temperature Sensor. Temperature Sensor Interrupt needs to be served before this bit can be cleaned.
-
enumerator kSRC_Wdog3ResetFlag
IC Watchdog3 Time-out reset. Indicates whether the reset was the result of the watchdog3 time-out event.
-
enumerator kSRC_SoftwareResetFlag
Indicates a reset has been caused by software setting of SYSRESETREQ bit in Application Interrupt and Reset Control Register in the ARM core.
-
enumerator kSRC_JTAGSystemResetFlag
Indicates whether the reset was the result of software reset form JTAG
-
enumerator kSRC_JTAGSoftwareResetFlag
Indicates whether the reset was the result of setting SJC_GPCCR bit 31.
-
enumerator kSRC_JTAGGeneratedResetFlag
Indicates a reset has been caused by JTAG selection of certain IR codes: EXTEST or HIGHZ.
-
enumerator kSRC_WatchdogResetFlag
Indicates a reset has been caused by the watchdog timer timing out. This reset source can be blocked by disabling the watchdog.
-
enumerator kSRC_IppUserResetFlag
Indicates whether the reset was the result of the ipp_user_reset_b qualified reset.
-
enumerator kSRC_SNVSFailResetFlag
SNVS hardware failure will always cause a cold reset. This flag indicates whether the reset is a result of SNVS hardware failure.
-
enumerator kSRC_CsuResetFlag
Indicates whether the reset was the result of the csu_reset_b input.
-
enumerator kSRC_CoreLockupResetFlag
Indicates a reset has been caused by the ARM core indication of a LOCKUP event.
-
enumerator kSRC_PowerOnResetFlag
Indicates a reset has been caused by the power-on detection logic.
-
enumerator kSRC_LockupSysResetFlag
Indicates a reset has been caused by CPU lockup or software setting of SYSRESETREQ bit in Application Interrupt and Reset Control Register of the ARM core.
-
enumerator kSRC_IppResetPinFlag
Indicates whether reset was the result of ipp_reset_b pin (Power-up sequence).
-
enumerator kSRC_ResetOutputEnableFlag
-
enum _src_status_flags
SRC interrupt status flag.
Values:
-
enumerator kSRC_Core0WdogResetReqFlag
WDOG reset request from core0. Read-only status bit.
-
enumerator kSRC_Core0WdogResetReqFlag
-
enum _src_mix_reset_stretch_cycles
Selection of SoC mix power reset stretch.
This type defines the SoC mix (Audio, ENET, uSDHC, EIM, QSPI, OCRAM, MMDC, etc) power up reset stretch mix reset width with the optional count of cycles
Values:
-
enumerator kSRC_MixResetStretchCycleAlt0
mix reset width is 1 x 88 ipg_cycle cycles.
-
enumerator kSRC_MixResetStretchCycleAlt1
mix reset width is 2 x 88 ipg_cycle cycles.
-
enumerator kSRC_MixResetStretchCycleAlt2
mix reset width is 3 x 88 ipg_cycle cycles.
-
enumerator kSRC_MixResetStretchCycleAlt3
mix reset width is 4 x 88 ipg_cycle cycles.
-
enumerator kSRC_MixResetStretchCycleAlt0
-
enum _src_wdog3_reset_option
Selection of WDOG3 reset option.
Values:
-
enumerator kSRC_Wdog3ResetOptionAlt0
Wdog3_rst_b asserts M4 reset (default).
-
enumerator kSRC_Wdog3ResetOptionAlt1
Wdog3_rst_b asserts global reset.
-
enumerator kSRC_Wdog3ResetOptionAlt0
-
enum _src_warm_reset_bypass_count
Selection of WARM reset bypass count.
This type defines the 32KHz clock cycles to count before bypassing the MMDC acknowledge for WARM reset. If the MMDC acknowledge is not asserted before this counter is elapsed, a COLD reset will be initiated.
Values:
-
enumerator kSRC_WarmResetWaitAlways
System will wait until MMDC acknowledge is asserted.
-
enumerator kSRC_WarmResetWaitClk16
Wait 16 32KHz clock cycles before switching the reset.
-
enumerator kSRC_WarmResetWaitClk32
Wait 32 32KHz clock cycles before switching the reset.
-
enumerator kSRC_WarmResetWaitClk64
Wait 64 32KHz clock cycles before switching the reset.
-
enumerator kSRC_WarmResetWaitAlways
-
typedef enum _src_mix_reset_stretch_cycles src_mix_reset_stretch_cycles_t
Selection of SoC mix power reset stretch.
This type defines the SoC mix (Audio, ENET, uSDHC, EIM, QSPI, OCRAM, MMDC, etc) power up reset stretch mix reset width with the optional count of cycles
-
typedef enum _src_wdog3_reset_option src_wdog3_reset_option_t
Selection of WDOG3 reset option.
-
typedef enum _src_warm_reset_bypass_count src_warm_reset_bypass_count_t
Selection of WARM reset bypass count.
This type defines the 32KHz clock cycles to count before bypassing the MMDC acknowledge for WARM reset. If the MMDC acknowledge is not asserted before this counter is elapsed, a COLD reset will be initiated.
-
static inline void SRC_EnableWDOG3Reset(SRC_Type *base, bool enable)
Enable the WDOG3 reset.
The WDOG3 reset is enabled by default.
- Parameters:
base – SRC peripheral base address.
enable – Enable the reset or not.
-
static inline void SRC_SetMixResetStretchCycles(SRC_Type *base, src_mix_reset_stretch_cycles_t option)
Set the mix power up reset stretch mix reset width.
- Parameters:
base – SRC peripheral base address.
option – Setting option, see to src_mix_reset_stretch_cycles_t.
-
static inline void SRC_EnableCoreDebugResetAfterPowerGate(SRC_Type *base, bool enable)
Debug reset would be asserted after power gating event.
- Parameters:
base – SRC peripheral base address.
enable – Enable the reset or not.
-
static inline void SRC_SetWdog3ResetOption(SRC_Type *base, src_wdog3_reset_option_t option)
Set the Wdog3_rst_b option.
- Parameters:
base – SRC peripheral base address.
option – Setting option, see to src_wdog3_reset_option_t.
-
static inline void SRC_DoSoftwareResetARMCoreDebug(SRC_Type *base)
Software reset for debug of arm platform only.
- Parameters:
base – SRC peripheral base address.
-
static inline bool SRC_GetSoftwareResetARMCoreDebugDone(SRC_Type *base)
Check if the software reset for debug of arm platform only is done.
- Parameters:
base – SRC peripheral base address.
-
static inline void SRC_EnableTemperatureSensorReset(SRC_Type *base, bool enable)
Enable the temperature sensor reset.
The temperature sersor reset is enabled by default. When the sensor reset happens, an flag bit would be asserted. This flag bit can be cleared only by the hardware reset.
- Parameters:
base – SRC peripheral base address.
enable – Enable the reset or not.
-
static inline void SRC_DoSoftwareResetARMCore0(SRC_Type *base)
Do software reset the ARM core0 only.
- Parameters:
base – SRC peripheral base address.
-
static inline bool SRC_GetSoftwareResetARMCore0Done(SRC_Type *base)
Check if the software for ARM core0 is done.
- Parameters:
base – SRC peripheral base address.
- Returns:
If the reset is done.
-
static inline void SRC_DoSoftwareResetARMCore(SRC_Type *base)
Do software reset for ARM core.
This function can be used to assert the ARM core reset. Once it is called, the reset process will begin. After the reset process is finished, the command bit would be self cleared.
- Parameters:
base – SRC peripheral base address.
-
static inline bool SRC_GetSoftwareResetARMCoreDone(SRC_Type *base)
Check if the software for ARM core is done.
- Parameters:
base – SRC peripheral base address.
- Returns:
If the reset is done.
-
static inline void SRC_AssertEIMReset(SRC_Type *base, bool enable)
Assert the EIM reset.
EIM reset is needed in order to reconfigure the EIM chip select. The software reset bit must de-asserted since this is not self-refresh.
- Parameters:
base – SRC peripheral base address.
enable – Make the assertion or not.
-
static inline void SRC_EnableWDOGReset(SRC_Type *base, bool enable)
Enable the WDOG Reset in SRC.
WDOG Reset is enabled in SRC by default. If the WDOG event to SRC is masked, it would not create a reset to the chip. During the time the WDOG event is masked, when the WDOG event flag is asserted, it would remain asserted regardless of servicing the WDOG module. The only way to clear that bit is the hardware reset.
- Parameters:
base – SRC peripheral base address.
enable – Enable the reset or not.
-
static inline void SRC_EnableLockupReset(SRC_Type *base, bool enable)
Enable the lockup reset.
- Parameters:
base – SRC peripheral base address.
enable – Enable the reset or not.
-
static inline void SRC_EnableCoreLockupReset(SRC_Type *base, bool enable)
Enable the core lockup reset.
When enable the core luckup reset, the system would be reset when core luckup event happens.
- Parameters:
base – SRC peripheral base address.
enable – Enable the reset or not.
-
static inline uint32_t SRC_GetStatusFlags(SRC_Type *base)
Get interrupt status flags.
- Parameters:
base – SRC peripheral base address.
- Returns:
Mask value of status flags. See to $_src_status_flags.
-
static inline uint32_t SRC_GetBootModeWord1(SRC_Type *base)
Get the boot mode register 1 value.
The Boot Mode register contains bits that reflect the status of BOOT_CFGx pins of the chip. See to chip-specific document for detail information about value.
- Parameters:
base – SRC peripheral base address.
- Returns:
status of BOOT_CFGx pins of the chip.
-
static inline uint32_t SRC_GetBootModeWord2(SRC_Type *base)
Get the boot mode register 2 value.
The Boot Mode register contains bits that reflect the status of BOOT_MODEx Pins and fuse values that controls boot of the chip. See to chip-specific document for detail information about value.
- Parameters:
base – SRC peripheral base address.
- Returns:
status of BOOT_MODEx Pins and fuse values that controls boot of the chip.
-
static inline uint32_t SRC_GetResetStatusFlags(SRC_Type *base)
Get the status flags of SRC.
- Parameters:
base – SRC peripheral base address.
- Returns:
Mask value of status flags, see to _src_reset_status_flags.
-
void SRC_ClearResetStatusFlags(SRC_Type *base, uint32_t flags)
Clear the status flags of SRC.
- Parameters:
base – SRC peripheral base address.
flags – value of status flags to be cleared, see to _src_reset_status_flags.
-
static inline void SRC_SetGeneralPurposeRegister(SRC_Type *base, uint32_t index, uint32_t value)
Set value to general purpose registers.
General purpose registers (GPRx) would hold the value during reset process. Wakeup function could be kept in these register. For example, the GPR1 holds the entry function for waking-up from Partial SLEEP mode while the GPR2 holds the argument. Other GPRx register would store the arbitray values.
- Parameters:
base – SRC peripheral base address.
index – The index of GPRx register array. Note index 0 reponses the GPR1 register.
value – Setting value for GPRx register.
-
static inline uint32_t SRC_GetGeneralPurposeRegister(SRC_Type *base, uint32_t index)
Get the value from general purpose registers.
- Parameters:
base – SRC peripheral base address.
index – The index of GPRx register array. Note index 0 reponses the GPR1 register.
- Returns:
The setting value for GPRx register.
TEMPMON: Temperature Monitor Module
-
FSL_TEMPMON_DRIVER_VERSION
TEMPMON driver version.
-
enum _tempmon_alarm_mode
TEMPMON alarm mode.
Values:
-
enumerator kTEMPMON_HighAlarmMode
The high alarm temperature interrupt mode.
-
enumerator kTEMPMON_PanicAlarmMode
The panic alarm temperature interrupt mode.
-
enumerator kTEMPMON_LowAlarmMode
The low alarm temperature interrupt mode.
-
enumerator kTEMPMON_HighAlarmMode
-
typedef struct _tempmon_config tempmon_config_t
TEMPMON temperature structure.
-
typedef enum _tempmon_alarm_mode tempmon_alarm_mode
TEMPMON alarm mode.
-
void TEMPMON_Init(TEMPMON_Type *base, const tempmon_config_t *config)
Initializes the TEMPMON module.
- Parameters:
base – TEMPMON base pointer
config – Pointer to configuration structure.
-
void TEMPMON_Deinit(TEMPMON_Type *base)
Deinitializes the TEMPMON module.
- Parameters:
base – TEMPMON base pointer
-
void TEMPMON_GetDefaultConfig(tempmon_config_t *config)
Gets the default configuration structure.
This function initializes the TEMPMON configuration structure to a default value. The default values are: tempmonConfig->frequency = 0x02U; tempmonConfig->highAlarmTemp = 44U; tempmonConfig->panicAlarmTemp = 90U; tempmonConfig->lowAlarmTemp = 39U;
- Parameters:
config – Pointer to a configuration structure.
-
static inline void TEMPMON_StartMeasure(TEMPMON_Type *base)
start the temperature measurement process.
- Parameters:
base – TEMPMON base pointer.
-
static inline void TEMPMON_StopMeasure(TEMPMON_Type *base)
stop the measurement process.
- Parameters:
base – TEMPMON base pointer
-
float TEMPMON_GetCurrentTemperature(TEMPMON_Type *base)
Get current temperature with the fused temperature calibration data.
- Parameters:
base – TEMPMON base pointer
- Returns:
current temperature with degrees Celsius.
-
void TEMPMON_SetTempAlarm(TEMPMON_Type *base, int16_t tempVal, tempmon_alarm_mode alarmMode)
Set the temperature count (raw sensor output) that will generate an alarm interrupt.
- Parameters:
base – TEMPMON base pointer
tempVal – The alarm temperature with degrees Celsius
alarmMode – The alarm mode.
-
struct _tempmon_config
- #include <fsl_tempmon.h>
TEMPMON temperature structure.
Public Members
-
uint16_t frequency
The temperature measure frequency.
-
int16_t highAlarmTemp
The high alarm temperature.
-
int16_t panicAlarmTemp
The panic alarm temperature.
-
int16_t lowAlarmTemp
The low alarm temperature.
-
uint16_t frequency
TRNG: True Random Number Generator
-
FSL_TRNG_DRIVER_VERSION
TRNG driver version 2.0.17.
Current version: 2.0.17
Change log:
version 2.0.17
Added support for RT700.
version 2.0.16
Added support for Dual oscillator mode.
version 2.0.15
Changed TRNG_USER_CONFIG_DEFAULT_XXX values according to latest reccomended by design team.
version 2.0.14
add support for RW610 and RW612
version 2.0.13
After deepsleep it might return error, added clearing bits in TRNG_GetRandomData() and generating new entropy.
Modified reloading entropy in TRNG_GetRandomData(), for some data length it doesn’t reloading entropy correctly.
version 2.0.12
For KW34A4_SERIES, KW35A4_SERIES, KW36A4_SERIES set TRNG_USER_CONFIG_DEFAULT_OSC_DIV to kTRNG_RingOscDiv8.
version 2.0.11
Add clearing pending errors in TRNG_Init().
version 2.0.10
Fixed doxygen issues.
version 2.0.9
Fix HIS_CCM metrics issues.
version 2.0.8
For K32L2A41A_SERIES set TRNG_USER_CONFIG_DEFAULT_OSC_DIV to kTRNG_RingOscDiv4.
version 2.0.7
Fix MISRA 2004 issue rule 12.5.
version 2.0.6
For KW35Z4_SERIES set TRNG_USER_CONFIG_DEFAULT_OSC_DIV to kTRNG_RingOscDiv8.
version 2.0.5
Add possibility to define default TRNG configuration by device specific preprocessor macros for FRQMIN, FRQMAX and OSCDIV.
version 2.0.4
Fix MISRA-2012 issues.
Version 2.0.3
update TRNG_Init to restart entropy generation
Version 2.0.2
fix MISRA issues
Version 2.0.1
add support for KL8x and KL28Z
update default OSCDIV for K81 to divide by 2
-
enum _trng_sample_mode
TRNG sample mode. Used by trng_config_t.
Values:
-
enumerator kTRNG_SampleModeVonNeumann
Use von Neumann data in both Entropy shifter and Statistical Checker.
-
enumerator kTRNG_SampleModeRaw
Use raw data into both Entropy shifter and Statistical Checker.
-
enumerator kTRNG_SampleModeVonNeumannRaw
Use von Neumann data in Entropy shifter. Use raw data into Statistical Checker.
-
enumerator kTRNG_SampleModeVonNeumann
-
enum _trng_clock_mode
TRNG clock mode. Used by trng_config_t.
Values:
-
enumerator kTRNG_ClockModeRingOscillator
Ring oscillator is used to operate the TRNG (default).
-
enumerator kTRNG_ClockModeSystem
System clock is used to operate the TRNG. This is for test use only, and indeterminate results may occur.
-
enumerator kTRNG_ClockModeRingOscillator
-
enum _trng_ring_osc_div
TRNG ring oscillator divide. Used by trng_config_t.
Values:
-
enumerator kTRNG_RingOscDiv0
Ring oscillator with no divide
-
enumerator kTRNG_RingOscDiv2
Ring oscillator divided-by-2.
-
enumerator kTRNG_RingOscDiv4
Ring oscillator divided-by-4.
-
enumerator kTRNG_RingOscDiv8
Ring oscillator divided-by-8.
-
enumerator kTRNG_RingOscDiv0
-
typedef enum _trng_sample_mode trng_sample_mode_t
TRNG sample mode. Used by trng_config_t.
-
typedef enum _trng_clock_mode trng_clock_mode_t
TRNG clock mode. Used by trng_config_t.
-
typedef enum _trng_ring_osc_div trng_ring_osc_div_t
TRNG ring oscillator divide. Used by trng_config_t.
-
typedef struct _trng_statistical_check_limit trng_statistical_check_limit_t
Data structure for definition of statistical check limits. Used by trng_config_t.
-
typedef struct _trng_user_config trng_config_t
Data structure for the TRNG initialization.
This structure initializes the TRNG by calling the TRNG_Init() function. It contains all TRNG configurations.
-
status_t TRNG_GetDefaultConfig(trng_config_t *userConfig)
Initializes the user configuration structure to default values.
This function initializes the configuration structure to default values. The default values are platform dependent.
- Parameters:
userConfig – User configuration structure.
- Returns:
If successful, returns the kStatus_TRNG_Success. Otherwise, it returns an error.
-
status_t TRNG_Init(TRNG_Type *base, const trng_config_t *userConfig)
Initializes the TRNG.
This function initializes the TRNG. When called, the TRNG entropy generation starts immediately.
- Parameters:
base – TRNG base address
userConfig – Pointer to the initialization configuration structure.
- Returns:
If successful, returns the kStatus_TRNG_Success. Otherwise, it returns an error.
-
void TRNG_Deinit(TRNG_Type *base)
Shuts down the TRNG.
This function shuts down the TRNG.
- Parameters:
base – TRNG base address.
-
status_t TRNG_GetRandomData(TRNG_Type *base, void *data, size_t dataSize)
Gets random data.
This function gets random data from the TRNG.
- Parameters:
base – TRNG base address.
data – Pointer address used to store random data.
dataSize – Size of the buffer pointed by the data parameter.
- Returns:
random data
-
struct _trng_statistical_check_limit
- #include <fsl_trng.h>
Data structure for definition of statistical check limits. Used by trng_config_t.
Public Members
-
uint32_t maximum
Maximum limit.
-
uint32_t minimum
Minimum limit.
-
uint32_t maximum
-
struct _trng_user_config
- #include <fsl_trng.h>
Data structure for the TRNG initialization.
This structure initializes the TRNG by calling the TRNG_Init() function. It contains all TRNG configurations.
Public Members
-
bool lock
Disable programmability of TRNG registers.
-
trng_clock_mode_t clockMode
Clock mode used to operate TRNG.
-
trng_ring_osc_div_t ringOscDiv
Ring oscillator divide used by TRNG.
-
trng_sample_mode_t sampleMode
Sample mode of the TRNG ring oscillator.
-
uint16_t entropyDelay
Entropy Delay. Defines the length (in system clocks) of each Entropy sample taken.
-
uint16_t sampleSize
Sample Size. Defines the total number of Entropy samples that will be taken during Entropy generation.
-
uint16_t sparseBitLimit
Sparse Bit Limit which defines the maximum number of consecutive samples that may be discarded before an error is generated. This limit is used only for during von Neumann sampling (enabled by TRNG_HAL_SetSampleMode()). Samples are discarded if two consecutive raw samples are both 0 or both 1. If this discarding occurs for a long period of time, it indicates that there is insufficient Entropy.
-
uint8_t retryCount
Retry count. It defines the number of times a statistical check may fails during the TRNG Entropy Generation before generating an error.
-
uint8_t longRunMaxLimit
Largest allowable number of consecutive samples of all 1, or all 0, that is allowed during the Entropy generation.
-
trng_statistical_check_limit_t monobitLimit
Maximum and minimum limits for statistical check of number of ones/zero detected during entropy generation.
-
trng_statistical_check_limit_t runBit1Limit
Maximum and minimum limits for statistical check of number of runs of length 1 detected during entropy generation.
-
trng_statistical_check_limit_t runBit2Limit
Maximum and minimum limits for statistical check of number of runs of length 2 detected during entropy generation.
-
trng_statistical_check_limit_t runBit3Limit
Maximum and minimum limits for statistical check of number of runs of length 3 detected during entropy generation.
-
trng_statistical_check_limit_t runBit4Limit
Maximum and minimum limits for statistical check of number of runs of length 4 detected during entropy generation.
-
trng_statistical_check_limit_t runBit5Limit
Maximum and minimum limits for statistical check of number of runs of length 5 detected during entropy generation.
-
trng_statistical_check_limit_t runBit6PlusLimit
Maximum and minimum limits for statistical check of number of runs of length 6 or more detected during entropy generation.
-
trng_statistical_check_limit_t pokerLimit
Maximum and minimum limits for statistical check of “Poker Test”.
-
trng_statistical_check_limit_t frequencyCountLimit
Maximum and minimum limits for statistical check of entropy sample frequency count.
-
bool lock
TSC: Touch Screen Controller Driver
-
enum _tsc_detection_mode
@ Controller detection mode.
Values:
-
enumerator kTSC_Detection4WireMode
4-Wire Detection Mode.
-
enumerator kTSC_Detection5WireMode
5-Wire Detection Mode.
-
enumerator kTSC_Detection4WireMode
-
enum _tsc_corrdinate_value_selection
@ Coordinate value mask.
Values:
-
enumerator kTSC_XCoordinateValueSelection
X coordinate value is selected.
-
enumerator kTSC_YCoordinateValueSelection
Y coordinate value is selected.
-
enumerator kTSC_XCoordinateValueSelection
-
enum _tsc_interrupt_signal_mask
@ Interrupt signal enable/disable mask.
Values:
-
enumerator kTSC_IdleSoftwareSignalEnable
Enable the interrupt signal when the controller has return to idle status. The signal is only valid after using TSC_ReturnToIdleStatus API.
-
enumerator kTSC_ValidSignalEnable
Enable the interrupt signal when controller receives a detect signal after measurement.
-
enumerator kTSC_DetectSignalEnable
Enable the interrupt signal when controller receives a detect signal.
-
enumerator kTSC_MeasureSignalEnable
Enable the interrupt signal after the touch detection which follows measurement.
-
enumerator kTSC_IdleSoftwareSignalEnable
-
enum _tsc_interrupt_mask
@ Interrupt enable/disable mask.
Values:
-
enumerator kTSC_IdleSoftwareInterruptEnable
Enable the interrupt when the controller has return to idle status. The interrupt is only valid after using TSC_ReturnToIdleStatus API.
-
enumerator kTSC_DetectInterruptEnable
Enable the interrupt when controller receive a detect signal.
-
enumerator kTSC_MeasureInterruptEnable
Enable the interrupt after the touch detection which follows measurement.
-
enumerator kTSC_IdleSoftwareInterruptEnable
-
enum _tsc_interrupt_status_flag_mask
@ Interrupt Status flag mask.
Values:
-
enumerator kTSC_IdleSoftwareFlag
This flag is set if the controller has return to idle status. The flag is only valid after using TSC_ReturnToIdleStatus API.
-
enumerator kTSC_ValidSignalFlag
This flag is set if controller receives a detect signal after measurement.
-
enumerator kTSC_DetectSignalFlag
This flag is set if controller receives a detect signal.
-
enumerator kTSC_MeasureSignalFlag
This flag is set after the touch detection which follows measurement. Note: Valid signal falg will be cleared along with measure signal flag.
-
enumerator kTSC_IdleSoftwareFlag
-
enum _tsc_adc_status_flag_mask
@ ADC status flag mask.
Values:
-
enumerator kTSC_ADCCOCOSignalFlag
This signal is generated by ADC when a conversion is completed.
-
enumerator kTSC_ADCConversionValueFlag
This signal is generated by ADC and indicates the result of an ADC conversion.
-
enumerator kTSC_ADCCOCOSignalFlag
-
enum _tsc_status_flag_mask
@ TSC status flag mask.
Values:
-
enumerator kTSC_IntermediateStateFlag
This flag is set if TSC is in intermediate state, between two state machine states.
-
enumerator kTSC_DetectFiveWireFlag
This flag is set if TSC receives a 5-wire detect signal. It is only valid when the TSC in detect state and DETECT_ENABLE_FIVE_WIRE bit is set.
-
enumerator kTSC_DetectFourWireFlag
This flag is set if TSC receives a 4-wire detect signal. It is only valid when the TSC in detect state and DETECT_ENABLE_FOUR_WIRE bit is set.
-
enumerator kTSC_GlitchThresholdFlag
This field indicates glitch threshold.The threshold is defined by number of clock cycles. See “tsc_glitch_threshold_t”. If value = 00, Normal function: 0x1fff ipg clock cycles, Low power mode: 0x9 low power clock cycles. If value = 01, Normal function: 0xfff ipg clock cycles, Low power mode: :0x7 low power clock cycles. If value = 10, Normal function: 0x7ff ipg clock cycles, Low power mode:0x5 low power clock cycles. If value = 11, Normal function: 0x3 ipg clock cycles, Low power mode:0x3 low power clock cycles.
-
enumerator kTSC_StateMachineFlag
This field indicates the state of TSC. See “tsc_state_machine_t”; if value = 000, Controller is in idle state. if value = 001, Controller is in 1st-Pre-charge state. if value = 010, Controller is in 1st-detect state. if value = 011, Controller is in x-measure state. if value = 100, Controller is in y-measure state. if value = 101, Controller is in 2nd-Pre-charge state. if value = 110, Controller is in 2nd-detect state.
-
enumerator kTSC_IntermediateStateFlag
-
enum _tsc_state_machine
TSC state machine. These seven states are TSC complete workflow.
Values:
-
enumerator kTSC_IdleState
Controller is in idle state.
-
enumerator kTSC_1stPreChargeState
Controller is in 1st-Pre-charge state.
-
enumerator kTSC_1stDetectState
Controller is in 1st-detect state.
-
enumerator kTSC_XMeasureState
Controller is in x-measure state.
-
enumerator kTSC_YMeasureState
Controller is in y-measure state.
-
enumerator kTSC_2ndPreChargeState
Controller is in 2nd-Pre-charge state.
-
enumerator kTSC_2ndDetectState
Controller is in 2nd-detect state.
-
enumerator kTSC_IdleState
-
enum _tsc_glitch_threshold
TSC glitch threshold.
Values:
-
enumerator kTSC_glitchThresholdALT0
Normal function: 0x1fff ipg clock cycles, Low power mode: 0x9 low power clock cycles.
-
enumerator kTSC_glitchThresholdALT1
Normal function: 0xfff ipg clock cycles, Low power mode: :0x7 low power clock cycles.
-
enumerator kTSC_glitchThresholdALT2
Normal function: 0x7ff ipg clock cycles, Low power mode: :0x5 low power clock cycles.
-
enumerator kTSC_glitchThresholdALT3
Normal function: 0x3 ipg clock cycles, Low power mode: :0x3 low power clock cycles.
-
enumerator kTSC_glitchThresholdALT0
-
enum _tsc_trigger_signal
@ Hardware trigger select signal, select which ADC channel to start conversion.
Values:
-
enumerator kTSC_TriggerToChannel0
Trigger to ADC channel0. ADC_HC0 register will be used to conversion.
-
enumerator kTSC_TriggerToChannel1
Trigger to ADC channel1. ADC_HC1 register will be used to conversion.
-
enumerator kTSC_TriggerToChannel2
Trigger to ADC channel2. ADC_HC2 register will be used to conversion.
-
enumerator kTSC_TriggerToChannel3
Trigger to ADC channel3. ADC_HC3 register will be used to conversion.
-
enumerator kTSC_TriggerToChannel4
Trigger to ADC channel4. ADC_HC4 register will be used to conversion.
-
enumerator kTSC_TriggerToChannel0
-
enum _tsc_port_source
@ TSC controller ports.
Values:
-
enumerator kTSC_WiperPortSource
TSC controller wiper port.
-
enumerator kTSC_YnlrPortSource
TSC controller ynlr port.
-
enumerator kTSC_YpllPortSource
TSC controller ypll port.
-
enumerator kTSC_XnurPortSource
TSC controller xnur port.
-
enumerator kTSC_XpulPortSource
TSC controller xpul port.
-
enumerator kTSC_WiperPortSource
-
enum _tsc_port_mode
@ TSC port mode.
Values:
-
enumerator kTSC_PortOffMode
Disable pull up/down mode.
-
enumerator kTSC_Port200k_PullUpMode
200k-pull up mode.
-
enumerator kTSC_PortPullUpMode
Pull up mode.
-
enumerator kTSC_PortPullDownMode
Pull down mode.
-
enumerator kTSC_PortOffMode
-
typedef enum _tsc_detection_mode tsc_detection_mode_t
@ Controller detection mode.
-
typedef enum _tsc_corrdinate_value_selection tsc_corrdinate_value_selection_t
@ Coordinate value mask.
-
typedef enum _tsc_state_machine tsc_state_machine_t
TSC state machine. These seven states are TSC complete workflow.
-
typedef enum _tsc_glitch_threshold tsc_glitch_threshold_t
TSC glitch threshold.
-
typedef enum _tsc_trigger_signal tsc_trigger_signal_t
@ Hardware trigger select signal, select which ADC channel to start conversion.
-
typedef enum _tsc_port_source tsc_port_source_t
@ TSC controller ports.
-
typedef enum _tsc_port_mode tsc_port_mode_t
@ TSC port mode.
-
typedef struct _tsc_config tsc_config_t
@ Controller configuration.
-
void TSC_Init(TSC_Type *base, const tsc_config_t *config)
Initialize the TSC module.
- Parameters:
base – TSC peripheral base address.
config – Pointer to “tsc_config_t” structure.
-
void TSC_Deinit(TSC_Type *base)
De-initializes the TSC module.
- Parameters:
base – TSC peripheral base address.
-
void TSC_GetDefaultConfig(tsc_config_t *config)
Gets an available pre-defined settings for the controller’s configuration.
This function initializes the converter configuration structure with available settings. The default values of measureDelayTime and prechargeTime is tested on LCD8000-43T screen and work normally. The default values are:
config->enableAutoMeausre = false; config->measureDelayTime = 0xFFFFU; config->prechargeTime = 0xFFFFU; config->detectionMode = kTSC_4WireDetectionMode;
- Parameters:
config – Pointer to “tsc_config_t” structure.
-
static inline void TSC_ReturnToIdleStatus(TSC_Type *base)
Make the TSC module return to idle status after finish the current state operation. Application could check TSC status to confirm that the controller has return to idle status.
- Parameters:
base – TSC peripheral base address.
-
static inline void TSC_StartSenseDetection(TSC_Type *base)
Start sense detection and (if work in auto-measure mode) measure after detect a touch.
- Parameters:
base – TSC peripheral base address.
-
static inline void TSC_StartMeasure(TSC_Type *base)
start measure X/Y coordinate value after detect a touch.
- Parameters:
base – TSC peripheral base address.
-
static inline void TSC_DropMeasure(TSC_Type *base)
Drop measure X/Y coordinate value after detect a touch and controller return to idle status.
- Parameters:
base – TSC peripheral base address.
-
static inline void TSC_SoftwareReset(TSC_Type *base)
This is a synchronization reset, which resets every register except IPS directly access ones.
- Parameters:
base – TSC peripheral base address.
-
uint32_t TSC_GetMeasureValue(TSC_Type *base, tsc_corrdinate_value_selection_t selection)
Get Y coordinate value or X coordinate value. The value is an ADC conversion value.
- Parameters:
base – TSC peripheral base address.
selection – Select alternative measure value which is Y coordinate value or X coordinate value. See “tsc_corrdinate_value_selection_t”.
- Returns:
If selection is “kTSC_XCoordinateValueSelection”, the API returns x-coordinate vlaue. If selection is “kTSC_YCoordinateValueSelection”, the API returns y-coordinate vlaue.
-
static inline void TSC_EnableInterruptSignals(TSC_Type *base, uint32_t mask)
Enable the interrupt signals. Interrupt signal will be set when corresponding event happens. Specific events point to “_tsc_interrupt_signal_mask” . Specific interrupt signal point to “_tsc_interrupt_status_flag_mask”;.
- Parameters:
base – TSC peripheral base address.
mask – Interrupt signals mask. See “_tsc_interrupt_signal_mask”.
-
static inline void TSC_DisableInterruptSignals(TSC_Type *base, uint32_t mask)
Disable the interrupt signals. Interrupt signal will be set when corresponding event happens. Specific events point to “_tsc_interrupt_signal_mask”. Specific interrupt signal point to “_tsc_interrupt_status_flag_mask”;.
- Parameters:
base – TSC peripheral base address.
mask – Interrupt signals mask. See “_tsc_interrupt_signal_mask”.
-
static inline void TSC_EnableInterrupts(TSC_Type *base, uint32_t mask)
Enable the interrupts. Notice: Only interrupts and signals are all enabled, interrupts could work normally.
- Parameters:
base – TSC peripheral base address.
mask – Interrupts mask. See “_tsc_interrupt_mask”.
-
static inline void TSC_DisableInterrupts(TSC_Type *base, uint32_t mask)
Disable the interrupts.
- Parameters:
base – TSC peripheral base address.
mask – Interrupts mask. See “_tsc_interrupt_mask”.
-
static inline uint32_t TSC_GetInterruptStatusFlags(TSC_Type *base)
Get interrupt status flags. Interrupt status falgs are valid when corresponding interrupt signals are enabled.
- Parameters:
base – TSC peripheral base address.
- Returns:
Status flags asserted mask. See “_tsc_interrupt_status_flag_mask”.
-
static inline void TSC_ClearInterruptStatusFlags(TSC_Type *base, uint32_t mask)
Clear interrupt status flags. Interrupt status falgs are valid when corresponding interrupt signals are enabled.
- Parameters:
base – TSC peripheral base address.
mask – Status flags mask. See “_tsc_interrupt_status_flag_mask”.
-
static inline uint32_t TSC_GetADCStatusFlags(TSC_Type *base)
Get the status flags of ADC working with TSC.
- Parameters:
base – TSC peripheral base address.
- Returns:
Status flags asserted mask. See “_tsc_adc_status_flag_mask”.
-
static inline uint32_t TSC_GetStatusFlags(TSC_Type *base)
Get the status flags of TSC.
- Parameters:
base – TSC peripheral base address.
- Returns:
Status flags asserted mask. See “_tsc_status_flag_mask”.
-
FSL_TSC_DRIVER_VERSION
TSC driver version.
Version 2.0.3.
-
struct _tsc_config
- #include <fsl_tsc.h>
@ Controller configuration.
Public Members
-
bool enableAutoMeasure
Enable the auto-measure. It indicates after detect touch, whether automatic start measurement
-
uint32_t measureDelayTime
Set delay time(0U~0xFFFFFFU) to even potential distribution ready.It is a preparation for measure stage. If measure dalay time is too short, maybe it would have an undesired effect on measure value.
-
uint32_t prechargeTime
Set pre-charge time(1U~0xFFFFFFFFU) to make the upper layer of screen to charge to positive high. It is a preparation for detection stage. Pre-charge time must is greater than 0U, otherwise TSC could not work normally. If pre-charge dalay time is too short, maybe it would have an undesired effect on generation of valid signal(kTSC_ValidSignalFlag).
-
tsc_detection_mode_t detectionMode
Select the detection mode. See “tsc_detection_mode_t”.
-
bool enableAutoMeasure
USDHC: Ultra Secured Digital Host Controller Driver
-
void USDHC_Init(USDHC_Type *base, const usdhc_config_t *config)
USDHC module initialization function.
Configures the USDHC according to the user configuration.
Example:
usdhc_config_t config; config.cardDetectDat3 = false; config.endianMode = kUSDHC_EndianModeLittle; config.dmaMode = kUSDHC_DmaModeAdma2; config.readWatermarkLevel = 128U; config.writeWatermarkLevel = 128U; USDHC_Init(USDHC, &config);
- Parameters:
base – USDHC peripheral base address.
config – USDHC configuration information.
- Return values:
kStatus_Success – Operate successfully.
-
void USDHC_Deinit(USDHC_Type *base)
Deinitializes the USDHC.
- Parameters:
base – USDHC peripheral base address.
-
bool USDHC_Reset(USDHC_Type *base, uint32_t mask, uint32_t timeout)
Resets the USDHC.
- Parameters:
base – USDHC peripheral base address.
mask – The reset type mask(_usdhc_reset).
timeout – Timeout for reset.
- Return values:
true – Reset successfully.
false – Reset failed.
-
status_t USDHC_SetAdmaTableConfig(USDHC_Type *base, usdhc_adma_config_t *dmaConfig, usdhc_data_t *dataConfig, uint32_t flags)
Sets the DMA descriptor table configuration. A high level DMA descriptor configuration function.
- Parameters:
base – USDHC peripheral base address.
dmaConfig – ADMA configuration
dataConfig – Data descriptor
flags – ADAM descriptor flag, used to indicate to create multiple or single descriptor, please refer to enum _usdhc_adma_flag.
- Return values:
kStatus_OutOfRange – ADMA descriptor table length isn’t enough to describe data.
kStatus_Success – Operate successfully.
-
status_t USDHC_SetInternalDmaConfig(USDHC_Type *base, usdhc_adma_config_t *dmaConfig, const uint32_t *dataAddr, bool enAutoCmd23)
Internal DMA configuration. This function is used to config the USDHC DMA related registers.
- Parameters:
base – USDHC peripheral base address.
dmaConfig – ADMA configuration.
dataAddr – Transfer data address, a simple DMA parameter, if ADMA is used, leave it to NULL.
enAutoCmd23 – Flag to indicate Auto CMD23 is enable or not, a simple DMA parameter, if ADMA is used, leave it to false.
- Return values:
kStatus_OutOfRange – ADMA descriptor table length isn’t enough to describe data.
kStatus_Success – Operate successfully.
-
status_t USDHC_SetADMA2Descriptor(uint32_t *admaTable, uint32_t admaTableWords, const uint32_t *dataBufferAddr, uint32_t dataBytes, uint32_t flags)
Sets the ADMA2 descriptor table configuration.
- Parameters:
admaTable – ADMA table address.
admaTableWords – ADMA table length.
dataBufferAddr – Data buffer address.
dataBytes – Data Data length.
flags – ADAM descriptor flag, used to indicate to create multiple or single descriptor, please refer to enum _usdhc_adma_flag.
- Return values:
kStatus_OutOfRange – ADMA descriptor table length isn’t enough to describe data.
kStatus_Success – Operate successfully.
-
status_t USDHC_SetADMA1Descriptor(uint32_t *admaTable, uint32_t admaTableWords, const uint32_t *dataBufferAddr, uint32_t dataBytes, uint32_t flags)
Sets the ADMA1 descriptor table configuration.
- Parameters:
admaTable – ADMA table address.
admaTableWords – ADMA table length.
dataBufferAddr – Data buffer address.
dataBytes – Data length.
flags – ADAM descriptor flag, used to indicate to create multiple or single descriptor, please refer to enum _usdhc_adma_flag.
- Return values:
kStatus_OutOfRange – ADMA descriptor table length isn’t enough to describe data.
kStatus_Success – Operate successfully.
-
static inline void USDHC_EnableInternalDMA(USDHC_Type *base, bool enable)
Enables internal DMA.
- Parameters:
base – USDHC peripheral base address.
enable – enable or disable flag
-
static inline void USDHC_EnableInterruptStatus(USDHC_Type *base, uint32_t mask)
Enables the interrupt status.
- Parameters:
base – USDHC peripheral base address.
mask – Interrupt status flags mask(_usdhc_interrupt_status_flag).
-
static inline void USDHC_DisableInterruptStatus(USDHC_Type *base, uint32_t mask)
Disables the interrupt status.
- Parameters:
base – USDHC peripheral base address.
mask – The interrupt status flags mask(_usdhc_interrupt_status_flag).
-
static inline void USDHC_EnableInterruptSignal(USDHC_Type *base, uint32_t mask)
Enables the interrupt signal corresponding to the interrupt status flag.
- Parameters:
base – USDHC peripheral base address.
mask – The interrupt status flags mask(_usdhc_interrupt_status_flag).
-
static inline void USDHC_DisableInterruptSignal(USDHC_Type *base, uint32_t mask)
Disables the interrupt signal corresponding to the interrupt status flag.
- Parameters:
base – USDHC peripheral base address.
mask – The interrupt status flags mask(_usdhc_interrupt_status_flag).
-
static inline uint32_t USDHC_GetEnabledInterruptStatusFlags(USDHC_Type *base)
Gets the enabled interrupt status.
- Parameters:
base – USDHC peripheral base address.
- Returns:
Current interrupt status flags mask(_usdhc_interrupt_status_flag).
-
static inline uint32_t USDHC_GetInterruptStatusFlags(USDHC_Type *base)
Gets the current interrupt status.
- Parameters:
base – USDHC peripheral base address.
- Returns:
Current interrupt status flags mask(_usdhc_interrupt_status_flag).
-
static inline void USDHC_ClearInterruptStatusFlags(USDHC_Type *base, uint32_t mask)
Clears a specified interrupt status. write 1 clears.
- Parameters:
base – USDHC peripheral base address.
mask – The interrupt status flags mask(_usdhc_interrupt_status_flag).
-
static inline uint32_t USDHC_GetAutoCommand12ErrorStatusFlags(USDHC_Type *base)
Gets the status of auto command 12 error.
- Parameters:
base – USDHC peripheral base address.
- Returns:
Auto command 12 error status flags mask(_usdhc_auto_command12_error_status_flag).
-
static inline uint32_t USDHC_GetAdmaErrorStatusFlags(USDHC_Type *base)
Gets the status of the ADMA error.
- Parameters:
base – USDHC peripheral base address.
- Returns:
ADMA error status flags mask(_usdhc_adma_error_status_flag).
-
static inline uint32_t USDHC_GetPresentStatusFlags(USDHC_Type *base)
Gets a present status.
This function gets the present USDHC’s status except for an interrupt status and an error status.
- Parameters:
base – USDHC peripheral base address.
- Returns:
Present USDHC’s status flags mask(_usdhc_present_status_flag).
-
void USDHC_GetCapability(USDHC_Type *base, usdhc_capability_t *capability)
Gets the capability information.
- Parameters:
base – USDHC peripheral base address.
capability – Structure to save capability information.
-
static inline void USDHC_ForceClockOn(USDHC_Type *base, bool enable)
Forces the card clock on.
- Parameters:
base – USDHC peripheral base address.
enable – enable/disable flag
-
uint32_t USDHC_SetSdClock(USDHC_Type *base, uint32_t srcClock_Hz, uint32_t busClock_Hz)
Sets the SD bus clock frequency.
- Parameters:
base – USDHC peripheral base address.
srcClock_Hz – USDHC source clock frequency united in Hz.
busClock_Hz – SD bus clock frequency united in Hz.
- Returns:
The nearest frequency of busClock_Hz configured for SD bus.
-
bool USDHC_SetCardActive(USDHC_Type *base, uint32_t timeout)
Sends 80 clocks to the card to set it to the active state.
This function must be called each time the card is inserted to ensure that the card can receive the command correctly.
- Parameters:
base – USDHC peripheral base address.
timeout – Timeout to initialize card.
- Return values:
true – Set card active successfully.
false – Set card active failed.
-
static inline void USDHC_AssertHardwareReset(USDHC_Type *base, bool high)
Triggers a hardware reset.
- Parameters:
base – USDHC peripheral base address.
high – 1 or 0 level
-
static inline void USDHC_SetDataBusWidth(USDHC_Type *base, usdhc_data_bus_width_t width)
Sets the data transfer width.
- Parameters:
base – USDHC peripheral base address.
width – Data transfer width.
-
static inline void USDHC_WriteData(USDHC_Type *base, uint32_t data)
Fills the data port.
This function is used to implement the data transfer by Data Port instead of DMA.
- Parameters:
base – USDHC peripheral base address.
data – The data about to be sent.
-
static inline uint32_t USDHC_ReadData(USDHC_Type *base)
Retrieves the data from the data port.
This function is used to implement the data transfer by Data Port instead of DMA.
- Parameters:
base – USDHC peripheral base address.
- Returns:
The data has been read.
-
void USDHC_SendCommand(USDHC_Type *base, usdhc_command_t *command)
Sends command function.
- Parameters:
base – USDHC peripheral base address.
command – configuration
-
static inline void USDHC_EnableWakeupEvent(USDHC_Type *base, uint32_t mask, bool enable)
Enables or disables a wakeup event in low-power mode.
- Parameters:
base – USDHC peripheral base address.
mask – Wakeup events mask(_usdhc_wakeup_event).
enable – True to enable, false to disable.
-
static inline void USDHC_CardDetectByData3(USDHC_Type *base, bool enable)
Detects card insert status.
- Parameters:
base – USDHC peripheral base address.
enable – enable/disable flag
-
static inline bool USDHC_DetectCardInsert(USDHC_Type *base)
Detects card insert status.
- Parameters:
base – USDHC peripheral base address.
-
static inline void USDHC_EnableSdioControl(USDHC_Type *base, uint32_t mask, bool enable)
Enables or disables the SDIO card control.
- Parameters:
base – USDHC peripheral base address.
mask – SDIO card control flags mask(_usdhc_sdio_control_flag).
enable – True to enable, false to disable.
-
static inline void USDHC_SetContinueRequest(USDHC_Type *base)
Restarts a transaction which has stopped at the block GAP for the SDIO card.
- Parameters:
base – USDHC peripheral base address.
-
static inline void USDHC_RequestStopAtBlockGap(USDHC_Type *base, bool enable)
Request stop at block gap function.
- Parameters:
base – USDHC peripheral base address.
enable – True to stop at block gap, false to normal transfer.
-
void USDHC_SetMmcBootConfig(USDHC_Type *base, const usdhc_boot_config_t *config)
Configures the MMC boot feature.
Example:
usdhc_boot_config_t config; config.ackTimeoutCount = 4; config.bootMode = kUSDHC_BootModeNormal; config.blockCount = 5; config.enableBootAck = true; config.enableBoot = true; config.enableAutoStopAtBlockGap = true; USDHC_SetMmcBootConfig(USDHC, &config);
- Parameters:
base – USDHC peripheral base address.
config – The MMC boot configuration information.
-
static inline void USDHC_EnableMmcBoot(USDHC_Type *base, bool enable)
Enables or disables the mmc boot mode.
- Parameters:
base – USDHC peripheral base address.
enable – True to enable, false to disable.
-
static inline void USDHC_SetForceEvent(USDHC_Type *base, uint32_t mask)
Forces generating events according to the given mask.
- Parameters:
base – USDHC peripheral base address.
mask – The force events bit posistion (_usdhc_force_event).
-
static inline bool USDHC_RequestTuningForSDR50(USDHC_Type *base)
Checks the SDR50 mode request tuning bit. When this bit set, application shall perform tuning for SDR50 mode.
- Parameters:
base – USDHC peripheral base address.
-
static inline bool USDHC_RequestReTuning(USDHC_Type *base)
Checks the request re-tuning bit. When this bit is set, user should do manual tuning or standard tuning function.
- Parameters:
base – USDHC peripheral base address.
-
static inline void USDHC_EnableAutoTuning(USDHC_Type *base, bool enable)
The SDR104 mode auto tuning enable and disable. This function should be called after tuning function execute pass, auto tuning will handle by hardware.
- Parameters:
base – USDHC peripheral base address.
enable – enable/disable flag
-
void USDHC_EnableAutoTuningForCmdAndData(USDHC_Type *base)
The auto tuning enbale for CMD/DATA line.
- Parameters:
base – USDHC peripheral base address.
-
void USDHC_EnableManualTuning(USDHC_Type *base, bool enable)
Manual tuning trigger or abort. User should handle the tuning cmd and find the boundary of the delay then calucate a average value which will be configured to the CLK_TUNE_CTRL_STATUS This function should be called before function USDHC_AdjustDelayForManualTuning.
- Parameters:
base – USDHC peripheral base address.
enable – tuning enable flag
-
static inline uint32_t USDHC_GetTuningDelayStatus(USDHC_Type *base)
Get the tuning delay cell setting.
- Parameters:
base – USDHC peripheral base address.
- Return values:
CLK – Tuning Control and Status register value.
-
status_t USDHC_SetTuningDelay(USDHC_Type *base, uint32_t preDelay, uint32_t outDelay, uint32_t postDelay)
The tuning delay cell setting.
- Parameters:
base – USDHC peripheral base address.
preDelay – Set the number of delay cells on the feedback clock between the feedback clock and CLK_PRE.
outDelay – Set the number of delay cells on the feedback clock between CLK_PRE and CLK_OUT.
postDelay – Set the number of delay cells on the feedback clock between CLK_OUT and CLK_POST.
- Return values:
kStatus_Fail – config the delay setting fail
kStatus_Success – config the delay setting success
-
status_t USDHC_AdjustDelayForManualTuning(USDHC_Type *base, uint32_t delay)
Adjusts delay for mannual tuning.
- Deprecated:
Do not use this function. It has been superceded by USDHC_SetTuingDelay
- Parameters:
base – USDHC peripheral base address.
delay – setting configuration
- Return values:
kStatus_Fail – config the delay setting fail
kStatus_Success – config the delay setting success
-
static inline void USDHC_SetStandardTuningCounter(USDHC_Type *base, uint8_t counter)
set tuning counter tuning.
- Parameters:
base – USDHC peripheral base address.
counter – tuning counter
- Return values:
kStatus_Fail – config the delay setting fail
kStatus_Success – config the delay setting success
-
void USDHC_EnableStandardTuning(USDHC_Type *base, uint32_t tuningStartTap, uint32_t step, bool enable)
The enable standard tuning function. The standard tuning window and tuning counter using the default config tuning cmd is sent by the software, user need to check whether the tuning result can be used for SDR50, SDR104, and HS200 mode tuning.
- Parameters:
base – USDHC peripheral base address.
tuningStartTap – start tap
step – tuning step
enable – enable/disable flag
-
static inline uint32_t USDHC_GetExecuteStdTuningStatus(USDHC_Type *base)
Gets execute STD tuning status.
- Parameters:
base – USDHC peripheral base address.
-
static inline uint32_t USDHC_CheckStdTuningResult(USDHC_Type *base)
Checks STD tuning result.
- Parameters:
base – USDHC peripheral base address.
-
static inline uint32_t USDHC_CheckTuningError(USDHC_Type *base)
Checks tuning error.
- Parameters:
base – USDHC peripheral base address.
-
void USDHC_EnableDDRMode(USDHC_Type *base, bool enable, uint32_t nibblePos)
The enable/disable DDR mode.
- Parameters:
base – USDHC peripheral base address.
enable – enable/disable flag
nibblePos – nibble position
-
static inline void USDHC_EnableHS400Mode(USDHC_Type *base, bool enable)
The enable/disable HS400 mode.
- Parameters:
base – USDHC peripheral base address.
enable – enable/disable flag
-
static inline void USDHC_ResetStrobeDLL(USDHC_Type *base)
Resets the strobe DLL.
- Parameters:
base – USDHC peripheral base address.
-
static inline void USDHC_EnableStrobeDLL(USDHC_Type *base, bool enable)
Enables/disables the strobe DLL.
- Parameters:
base – USDHC peripheral base address.
enable – enable/disable flag
-
void USDHC_ConfigStrobeDLL(USDHC_Type *base, uint32_t delayTarget, uint32_t updateInterval)
Configs the strobe DLL delay target and update interval.
- Parameters:
base – USDHC peripheral base address.
delayTarget – delay target
updateInterval – update interval
-
static inline void USDHC_SetStrobeDllOverride(USDHC_Type *base, uint32_t delayTaps)
Enables manual override for slave delay chain using STROBE_SLV_OVERRIDE_VAL.
- Parameters:
base – USDHC peripheral base address.
delayTaps – Valid delay taps range from 1 - 128 taps. A value of 0 selects tap 1, and a value of 0x7F selects tap 128.
-
static inline uint32_t USDHC_GetStrobeDLLStatus(USDHC_Type *base)
Gets the strobe DLL status.
- Parameters:
base – USDHC peripheral base address.
-
void USDHC_SetDataConfig(USDHC_Type *base, usdhc_transfer_direction_t dataDirection, uint32_t blockCount, uint32_t blockSize)
USDHC data configuration.
- Parameters:
base – USDHC peripheral base address.
dataDirection – Data direction, tx or rx.
blockCount – Data block count.
blockSize – Data block size.
-
void USDHC_TransferCreateHandle(USDHC_Type *base, usdhc_handle_t *handle, const usdhc_transfer_callback_t *callback, void *userData)
Creates the USDHC handle.
- Parameters:
base – USDHC peripheral base address.
handle – USDHC handle pointer.
callback – Structure pointer to contain all callback functions.
userData – Callback function parameter.
-
status_t USDHC_TransferNonBlocking(USDHC_Type *base, usdhc_handle_t *handle, usdhc_adma_config_t *dmaConfig, usdhc_transfer_t *transfer)
Transfers the command/data using an interrupt and an asynchronous method.
This function sends a command and data and returns immediately. It doesn’t wait for the transfer to complete or to encounter an error. The application must not call this API in multiple threads at the same time. Because of that this API doesn’t support the re-entry mechanism.
Note
Call API USDHC_TransferCreateHandle when calling this API.
- Parameters:
base – USDHC peripheral base address.
handle – USDHC handle.
dmaConfig – ADMA configuration.
transfer – Transfer content.
- Return values:
kStatus_InvalidArgument – Argument is invalid.
kStatus_USDHC_BusyTransferring – Busy transferring.
kStatus_USDHC_PrepareAdmaDescriptorFailed – Prepare ADMA descriptor failed.
kStatus_Success – Operate successfully.
-
status_t USDHC_TransferBlocking(USDHC_Type *base, usdhc_adma_config_t *dmaConfig, usdhc_transfer_t *transfer)
Transfers the command/data using a blocking method.
This function waits until the command response/data is received or the USDHC encounters an error by polling the status flag.
The application must not call this API in multiple threads at the same time. Because this API doesn’t support the re-entry mechanism.
Note
There is no need to call API USDHC_TransferCreateHandle when calling this API.
- Parameters:
base – USDHC peripheral base address.
dmaConfig – adma configuration
transfer – Transfer content.
- Return values:
kStatus_InvalidArgument – Argument is invalid.
kStatus_USDHC_PrepareAdmaDescriptorFailed – Prepare ADMA descriptor failed.
kStatus_USDHC_SendCommandFailed – Send command failed.
kStatus_USDHC_TransferDataFailed – Transfer data failed.
kStatus_Success – Operate successfully.
-
void USDHC_TransferHandleIRQ(USDHC_Type *base, usdhc_handle_t *handle)
IRQ handler for the USDHC.
This function deals with the IRQs on the given host controller.
- Parameters:
base – USDHC peripheral base address.
handle – USDHC handle.
-
FSL_USDHC_DRIVER_VERSION
Driver version 2.8.4.
Enum _usdhc_status. USDHC status.
Values:
-
enumerator kStatus_USDHC_BusyTransferring
Transfer is on-going.
-
enumerator kStatus_USDHC_PrepareAdmaDescriptorFailed
Set DMA descriptor failed.
-
enumerator kStatus_USDHC_SendCommandFailed
Send command failed.
-
enumerator kStatus_USDHC_TransferDataFailed
Transfer data failed.
-
enumerator kStatus_USDHC_DMADataAddrNotAlign
Data address not aligned.
-
enumerator kStatus_USDHC_ReTuningRequest
Re-tuning request.
-
enumerator kStatus_USDHC_TuningError
Tuning error.
-
enumerator kStatus_USDHC_NotSupport
Not support.
-
enumerator kStatus_USDHC_TransferDataComplete
Transfer data complete.
-
enumerator kStatus_USDHC_SendCommandSuccess
Transfer command complete.
-
enumerator kStatus_USDHC_TransferDMAComplete
Transfer DMA complete.
-
enumerator kStatus_USDHC_BusyTransferring
Enum _usdhc_capability_flag. Host controller capabilities flag mask. .
Values:
-
enumerator kUSDHC_SupportAdmaFlag
Support ADMA.
-
enumerator kUSDHC_SupportHighSpeedFlag
Support high-speed.
-
enumerator kUSDHC_SupportDmaFlag
Support DMA.
-
enumerator kUSDHC_SupportSuspendResumeFlag
Support suspend/resume.
-
enumerator kUSDHC_SupportV330Flag
Support voltage 3.3V.
-
enumerator kUSDHC_SupportV300Flag
Support voltage 3.0V.
-
enumerator kUSDHC_Support4BitFlag
Flag in HTCAPBLT_MBL’s position, supporting 4-bit mode.
-
enumerator kUSDHC_Support8BitFlag
Flag in HTCAPBLT_MBL’s position, supporting 8-bit mode.
-
enumerator kUSDHC_SupportDDR50Flag
SD version 3.0 new feature, supporting DDR50 mode.
-
enumerator kUSDHC_SupportSDR104Flag
Support SDR104 mode.
-
enumerator kUSDHC_SupportSDR50Flag
Support SDR50 mode.
-
enumerator kUSDHC_SupportAdmaFlag
Enum _usdhc_wakeup_event. Wakeup event mask. .
Values:
-
enumerator kUSDHC_WakeupEventOnCardInt
Wakeup on card interrupt.
-
enumerator kUSDHC_WakeupEventOnCardInsert
Wakeup on card insertion.
-
enumerator kUSDHC_WakeupEventOnCardRemove
Wakeup on card removal.
-
enumerator kUSDHC_WakeupEventsAll
All wakeup events
-
enumerator kUSDHC_WakeupEventOnCardInt
Enum _usdhc_reset. Reset type mask. .
Values:
-
enumerator kUSDHC_ResetAll
Reset all except card detection.
-
enumerator kUSDHC_ResetCommand
Reset command line.
-
enumerator kUSDHC_ResetData
Reset data line.
-
enumerator kUSDHC_ResetTuning
Reset tuning circuit.
-
enumerator kUSDHC_ResetsAll
All reset types
-
enumerator kUSDHC_ResetAll
Enum _usdhc_transfer_flag. Transfer flag mask.
Values:
-
enumerator kUSDHC_EnableDmaFlag
Enable DMA.
-
enumerator kUSDHC_CommandTypeSuspendFlag
Suspend command.
-
enumerator kUSDHC_CommandTypeResumeFlag
Resume command.
-
enumerator kUSDHC_CommandTypeAbortFlag
Abort command.
-
enumerator kUSDHC_EnableBlockCountFlag
Enable block count.
-
enumerator kUSDHC_EnableAutoCommand12Flag
Enable auto CMD12.
-
enumerator kUSDHC_DataReadFlag
Enable data read.
-
enumerator kUSDHC_MultipleBlockFlag
Multiple block data read/write.
-
enumerator kUSDHC_EnableAutoCommand23Flag
Enable auto CMD23.
-
enumerator kUSDHC_ResponseLength136Flag
136-bit response length.
-
enumerator kUSDHC_ResponseLength48Flag
48-bit response length.
-
enumerator kUSDHC_ResponseLength48BusyFlag
48-bit response length with busy status.
-
enumerator kUSDHC_EnableCrcCheckFlag
Enable CRC check.
-
enumerator kUSDHC_EnableIndexCheckFlag
Enable index check.
-
enumerator kUSDHC_DataPresentFlag
Data present flag.
-
enumerator kUSDHC_EnableDmaFlag
Enum _usdhc_present_status_flag. Present status flag mask. .
Values:
-
enumerator kUSDHC_CommandInhibitFlag
Command inhibit.
-
enumerator kUSDHC_DataInhibitFlag
Data inhibit.
-
enumerator kUSDHC_DataLineActiveFlag
Data line active.
-
enumerator kUSDHC_SdClockStableFlag
SD bus clock stable.
-
enumerator kUSDHC_WriteTransferActiveFlag
Write transfer active.
-
enumerator kUSDHC_ReadTransferActiveFlag
Read transfer active.
-
enumerator kUSDHC_BufferWriteEnableFlag
Buffer write enable.
-
enumerator kUSDHC_BufferReadEnableFlag
Buffer read enable.
-
enumerator kUSDHC_ReTuningRequestFlag
Re-tuning request flag, only used for SDR104 mode.
-
enumerator kUSDHC_DelaySettingFinishedFlag
Delay setting finished flag.
-
enumerator kUSDHC_CardInsertedFlag
Card inserted.
-
enumerator kUSDHC_CommandLineLevelFlag
Command line signal level.
-
enumerator kUSDHC_Data0LineLevelFlag
Data0 line signal level.
-
enumerator kUSDHC_Data1LineLevelFlag
Data1 line signal level.
-
enumerator kUSDHC_Data2LineLevelFlag
Data2 line signal level.
-
enumerator kUSDHC_Data3LineLevelFlag
Data3 line signal level.
-
enumerator kUSDHC_Data4LineLevelFlag
Data4 line signal level.
-
enumerator kUSDHC_Data5LineLevelFlag
Data5 line signal level.
-
enumerator kUSDHC_Data6LineLevelFlag
Data6 line signal level.
-
enumerator kUSDHC_Data7LineLevelFlag
Data7 line signal level.
-
enumerator kUSDHC_CommandInhibitFlag
Enum _usdhc_interrupt_status_flag. Interrupt status flag mask. .
Values:
-
enumerator kUSDHC_CommandCompleteFlag
Command complete.
-
enumerator kUSDHC_DataCompleteFlag
Data complete.
-
enumerator kUSDHC_BlockGapEventFlag
Block gap event.
-
enumerator kUSDHC_DmaCompleteFlag
DMA interrupt.
-
enumerator kUSDHC_BufferWriteReadyFlag
Buffer write ready.
-
enumerator kUSDHC_BufferReadReadyFlag
Buffer read ready.
-
enumerator kUSDHC_CardInsertionFlag
Card inserted.
-
enumerator kUSDHC_CardRemovalFlag
Card removed.
-
enumerator kUSDHC_CardInterruptFlag
Card interrupt.
-
enumerator kUSDHC_ReTuningEventFlag
Re-Tuning event, only for SD3.0 SDR104 mode.
-
enumerator kUSDHC_TuningPassFlag
SDR104 mode tuning pass flag.
-
enumerator kUSDHC_TuningErrorFlag
SDR104 tuning error flag.
-
enumerator kUSDHC_CommandTimeoutFlag
Command timeout error.
-
enumerator kUSDHC_CommandCrcErrorFlag
Command CRC error.
-
enumerator kUSDHC_CommandEndBitErrorFlag
Command end bit error.
-
enumerator kUSDHC_CommandIndexErrorFlag
Command index error.
-
enumerator kUSDHC_DataTimeoutFlag
Data timeout error.
-
enumerator kUSDHC_DataCrcErrorFlag
Data CRC error.
-
enumerator kUSDHC_DataEndBitErrorFlag
Data end bit error.
-
enumerator kUSDHC_AutoCommand12ErrorFlag
Auto CMD12 error.
-
enumerator kUSDHC_DmaErrorFlag
DMA error.
-
enumerator kUSDHC_CommandErrorFlag
Command error
-
enumerator kUSDHC_DataErrorFlag
Data error
-
enumerator kUSDHC_ErrorFlag
All error
-
enumerator kUSDHC_DataFlag
Data interrupts
-
enumerator kUSDHC_DataDMAFlag
Data interrupts
-
enumerator kUSDHC_CommandFlag
Command interrupts
-
enumerator kUSDHC_CardDetectFlag
Card detection interrupts
-
enumerator kUSDHC_SDR104TuningFlag
SDR104 tuning flag.
-
enumerator kUSDHC_AllInterruptFlags
All flags mask
-
enumerator kUSDHC_CommandCompleteFlag
Enum _usdhc_auto_command12_error_status_flag. Auto CMD12 error status flag mask. .
Values:
-
enumerator kUSDHC_AutoCommand12NotExecutedFlag
Not executed error.
-
enumerator kUSDHC_AutoCommand12TimeoutFlag
Timeout error.
-
enumerator kUSDHC_AutoCommand12EndBitErrorFlag
End bit error.
-
enumerator kUSDHC_AutoCommand12CrcErrorFlag
CRC error.
-
enumerator kUSDHC_AutoCommand12IndexErrorFlag
Index error.
-
enumerator kUSDHC_AutoCommand12NotIssuedFlag
Not issued error.
-
enumerator kUSDHC_AutoCommand12NotExecutedFlag
Enum _usdhc_standard_tuning. Standard tuning flag.
Values:
-
enumerator kUSDHC_ExecuteTuning
Used to start tuning procedure.
-
enumerator kUSDHC_TuningSampleClockSel
When std_tuning_en bit is set, this bit is used to select sampleing clock.
-
enumerator kUSDHC_ExecuteTuning
Enum _usdhc_adma_error_status_flag. ADMA error status flag mask. .
Values:
-
enumerator kUSDHC_AdmaLenghMismatchFlag
Length mismatch error.
-
enumerator kUSDHC_AdmaDescriptorErrorFlag
Descriptor error.
-
enumerator kUSDHC_AdmaLenghMismatchFlag
Enum _usdhc_adma_error_state. ADMA error state.
This state is the detail state when ADMA error has occurred.
Values:
-
enumerator kUSDHC_AdmaErrorStateStopDma
Stop DMA, previous location set in the ADMA system address is errored address.
-
enumerator kUSDHC_AdmaErrorStateFetchDescriptor
Fetch descriptor, current location set in the ADMA system address is errored address.
-
enumerator kUSDHC_AdmaErrorStateChangeAddress
Change address, no DMA error has occurred.
-
enumerator kUSDHC_AdmaErrorStateTransferData
Transfer data, previous location set in the ADMA system address is errored address.
-
enumerator kUSDHC_AdmaErrorStateInvalidLength
Invalid length in ADMA descriptor.
-
enumerator kUSDHC_AdmaErrorStateInvalidDescriptor
Invalid descriptor fetched by ADMA.
-
enumerator kUSDHC_AdmaErrorState
ADMA error state
-
enumerator kUSDHC_AdmaErrorStateStopDma
Enum _usdhc_force_event. Force event bit position. .
Values:
-
enumerator kUSDHC_ForceEventAutoCommand12NotExecuted
Auto CMD12 not executed error.
-
enumerator kUSDHC_ForceEventAutoCommand12Timeout
Auto CMD12 timeout error.
-
enumerator kUSDHC_ForceEventAutoCommand12CrcError
Auto CMD12 CRC error.
-
enumerator kUSDHC_ForceEventEndBitError
Auto CMD12 end bit error.
-
enumerator kUSDHC_ForceEventAutoCommand12IndexError
Auto CMD12 index error.
-
enumerator kUSDHC_ForceEventAutoCommand12NotIssued
Auto CMD12 not issued error.
-
enumerator kUSDHC_ForceEventCommandTimeout
Command timeout error.
-
enumerator kUSDHC_ForceEventCommandCrcError
Command CRC error.
-
enumerator kUSDHC_ForceEventCommandEndBitError
Command end bit error.
-
enumerator kUSDHC_ForceEventCommandIndexError
Command index error.
-
enumerator kUSDHC_ForceEventDataTimeout
Data timeout error.
-
enumerator kUSDHC_ForceEventDataCrcError
Data CRC error.
-
enumerator kUSDHC_ForceEventDataEndBitError
Data end bit error.
-
enumerator kUSDHC_ForceEventAutoCommand12Error
Auto CMD12 error.
-
enumerator kUSDHC_ForceEventCardInt
Card interrupt.
-
enumerator kUSDHC_ForceEventDmaError
Dma error.
-
enumerator kUSDHC_ForceEventTuningError
Tuning error.
-
enumerator kUSDHC_ForceEventsAll
All force event flags mask.
-
enumerator kUSDHC_ForceEventAutoCommand12NotExecuted
-
enum _usdhc_transfer_direction
Data transfer direction.
Values:
-
enumerator kUSDHC_TransferDirectionReceive
USDHC transfer direction receive.
-
enumerator kUSDHC_TransferDirectionSend
USDHC transfer direction send.
-
enumerator kUSDHC_TransferDirectionReceive
-
enum _usdhc_data_bus_width
Data transfer width.
Values:
-
enumerator kUSDHC_DataBusWidth1Bit
1-bit mode
-
enumerator kUSDHC_DataBusWidth4Bit
4-bit mode
-
enumerator kUSDHC_DataBusWidth8Bit
8-bit mode
-
enumerator kUSDHC_DataBusWidth1Bit
-
enum _usdhc_endian_mode
Endian mode.
Values:
-
enumerator kUSDHC_EndianModeBig
Big endian mode.
-
enumerator kUSDHC_EndianModeHalfWordBig
Half word big endian mode.
-
enumerator kUSDHC_EndianModeLittle
Little endian mode.
-
enumerator kUSDHC_EndianModeBig
-
enum _usdhc_dma_mode
DMA mode.
Values:
-
enumerator kUSDHC_DmaModeSimple
External DMA.
-
enumerator kUSDHC_DmaModeAdma1
ADMA1 is selected.
-
enumerator kUSDHC_DmaModeAdma2
ADMA2 is selected.
-
enumerator kUSDHC_ExternalDMA
External DMA mode selected.
-
enumerator kUSDHC_DmaModeSimple
Enum _usdhc_sdio_control_flag. SDIO control flag mask. .
Values:
-
enumerator kUSDHC_StopAtBlockGapFlag
Stop at block gap.
-
enumerator kUSDHC_ReadWaitControlFlag
Read wait control.
-
enumerator kUSDHC_InterruptAtBlockGapFlag
Interrupt at block gap.
-
enumerator kUSDHC_ReadDoneNo8CLK
Read done without 8 clk for block gap.
-
enumerator kUSDHC_ExactBlockNumberReadFlag
Exact block number read.
-
enumerator kUSDHC_StopAtBlockGapFlag
-
enum _usdhc_boot_mode
MMC card boot mode.
Values:
-
enumerator kUSDHC_BootModeNormal
Normal boot
-
enumerator kUSDHC_BootModeAlternative
Alternative boot
-
enumerator kUSDHC_BootModeNormal
-
enum _usdhc_card_command_type
The command type.
Values:
-
enumerator kCARD_CommandTypeNormal
Normal command
-
enumerator kCARD_CommandTypeSuspend
Suspend command
-
enumerator kCARD_CommandTypeResume
Resume command
-
enumerator kCARD_CommandTypeAbort
Abort command
-
enumerator kCARD_CommandTypeEmpty
Empty command
-
enumerator kCARD_CommandTypeNormal
-
enum _usdhc_card_response_type
The command response type.
Defines the command response type from card to host controller.
Values:
-
enumerator kCARD_ResponseTypeNone
Response type: none
-
enumerator kCARD_ResponseTypeR1
Response type: R1
-
enumerator kCARD_ResponseTypeR1b
Response type: R1b
-
enumerator kCARD_ResponseTypeR2
Response type: R2
-
enumerator kCARD_ResponseTypeR3
Response type: R3
-
enumerator kCARD_ResponseTypeR4
Response type: R4
-
enumerator kCARD_ResponseTypeR5
Response type: R5
-
enumerator kCARD_ResponseTypeR5b
Response type: R5b
-
enumerator kCARD_ResponseTypeR6
Response type: R6
-
enumerator kCARD_ResponseTypeR7
Response type: R7
-
enumerator kCARD_ResponseTypeNone
Enum _usdhc_adma1_descriptor_flag. The mask for the control/status field in ADMA1 descriptor.
Values:
-
enumerator kUSDHC_Adma1DescriptorValidFlag
Valid flag.
-
enumerator kUSDHC_Adma1DescriptorEndFlag
End flag.
-
enumerator kUSDHC_Adma1DescriptorInterrupFlag
Interrupt flag.
-
enumerator kUSDHC_Adma1DescriptorActivity1Flag
Activity 1 flag.
-
enumerator kUSDHC_Adma1DescriptorActivity2Flag
Activity 2 flag.
-
enumerator kUSDHC_Adma1DescriptorTypeNop
No operation.
-
enumerator kUSDHC_Adma1DescriptorTypeTransfer
Transfer data.
-
enumerator kUSDHC_Adma1DescriptorTypeLink
Link descriptor.
-
enumerator kUSDHC_Adma1DescriptorTypeSetLength
Set data length.
-
enumerator kUSDHC_Adma1DescriptorValidFlag
Enum _usdhc_adma2_descriptor_flag. ADMA1 descriptor control and status mask.
Values:
-
enumerator kUSDHC_Adma2DescriptorValidFlag
Valid flag.
-
enumerator kUSDHC_Adma2DescriptorEndFlag
End flag.
-
enumerator kUSDHC_Adma2DescriptorInterruptFlag
Interrupt flag.
-
enumerator kUSDHC_Adma2DescriptorActivity1Flag
Activity 1 mask.
-
enumerator kUSDHC_Adma2DescriptorActivity2Flag
Activity 2 mask.
-
enumerator kUSDHC_Adma2DescriptorTypeNop
No operation.
-
enumerator kUSDHC_Adma2DescriptorTypeReserved
Reserved.
-
enumerator kUSDHC_Adma2DescriptorTypeTransfer
Transfer type.
-
enumerator kUSDHC_Adma2DescriptorTypeLink
Link type.
-
enumerator kUSDHC_Adma2DescriptorValidFlag
Enum _usdhc_adma_flag. ADMA descriptor configuration flag. .
Values:
-
enumerator kUSDHC_AdmaDescriptorSingleFlag
Try to finish the transfer in a single ADMA descriptor. If transfer size is bigger than one ADMA descriptor’s ability, new another descriptor for data transfer.
-
enumerator kUSDHC_AdmaDescriptorMultipleFlag
Create multiple ADMA descriptors within the ADMA table, this is used for mmc boot mode specifically, which need to modify the ADMA descriptor on the fly, so the flag should be used combining with stop at block gap feature.
-
enumerator kUSDHC_AdmaDescriptorSingleFlag
-
enum _usdhc_burst_len
DMA transfer burst len config.
Values:
-
enumerator kUSDHC_EnBurstLenForINCR
Enable burst len for INCR.
-
enumerator kUSDHC_EnBurstLenForINCR4816
Enable burst len for INCR4/INCR8/INCR16.
-
enumerator kUSDHC_EnBurstLenForINCR4816WRAP
Enable burst len for INCR4/8/16 WRAP.
-
enumerator kUSDHC_EnBurstLenForINCR
Enum _usdhc_transfer_data_type. Tansfer data type definition.
Values:
-
enumerator kUSDHC_TransferDataNormal
Transfer normal read/write data.
-
enumerator kUSDHC_TransferDataTuning
Transfer tuning data.
-
enumerator kUSDHC_TransferDataBoot
Transfer boot data.
-
enumerator kUSDHC_TransferDataBootcontinous
Transfer boot data continuously.
-
enumerator kUSDHC_TransferDataNormal
-
typedef enum _usdhc_transfer_direction usdhc_transfer_direction_t
Data transfer direction.
-
typedef enum _usdhc_data_bus_width usdhc_data_bus_width_t
Data transfer width.
-
typedef enum _usdhc_endian_mode usdhc_endian_mode_t
Endian mode.
-
typedef enum _usdhc_dma_mode usdhc_dma_mode_t
DMA mode.
-
typedef enum _usdhc_boot_mode usdhc_boot_mode_t
MMC card boot mode.
-
typedef enum _usdhc_card_command_type usdhc_card_command_type_t
The command type.
-
typedef enum _usdhc_card_response_type usdhc_card_response_type_t
The command response type.
Defines the command response type from card to host controller.
-
typedef enum _usdhc_burst_len usdhc_burst_len_t
DMA transfer burst len config.
-
typedef uint32_t usdhc_adma1_descriptor_t
Defines the ADMA1 descriptor structure.
-
typedef struct _usdhc_adma2_descriptor usdhc_adma2_descriptor_t
Defines the ADMA2 descriptor structure.
-
typedef struct _usdhc_capability usdhc_capability_t
USDHC capability information.
Defines a structure to save the capability information of USDHC.
-
typedef struct _usdhc_boot_config usdhc_boot_config_t
Data structure to configure the MMC boot feature.
-
typedef struct _usdhc_config usdhc_config_t
Data structure to initialize the USDHC.
-
typedef struct _usdhc_command usdhc_command_t
Card command descriptor.
Defines card command-related attribute.
-
typedef struct _usdhc_adma_config usdhc_adma_config_t
ADMA configuration.
-
typedef struct _usdhc_scatter_gather_data_list usdhc_scatter_gather_data_list_t
Card scatter gather data list.
Allow application register uncontinuous data buffer for data transfer.
-
typedef struct _usdhc_scatter_gather_data usdhc_scatter_gather_data_t
Card scatter gather data descriptor.
Defines a structure to contain data-related attribute. The ‘enableIgnoreError’ is used when upper card driver wants to ignore the error event to read/write all the data and not to stop read/write immediately when an error event happens. For example, bus testing procedure for MMC card.
-
typedef struct _usdhc_scatter_gather_transfer usdhc_scatter_gather_transfer_t
usdhc scatter gather transfer.
-
typedef struct _usdhc_data usdhc_data_t
Card data descriptor.
Defines a structure to contain data-related attribute. The ‘enableIgnoreError’ is used when upper card driver wants to ignore the error event to read/write all the data and not to stop read/write immediately when an error event happens. For example, bus testing procedure for MMC card.
-
typedef struct _usdhc_transfer usdhc_transfer_t
Transfer state.
-
typedef struct _usdhc_handle usdhc_handle_t
USDHC handle typedef.
-
typedef struct _usdhc_transfer_callback usdhc_transfer_callback_t
USDHC callback functions.
-
typedef status_t (*usdhc_transfer_function_t)(USDHC_Type *base, usdhc_transfer_t *content)
USDHC transfer function.
-
typedef struct _usdhc_host usdhc_host_t
USDHC host descriptor.
-
USDHC_MAX_BLOCK_COUNT
Maximum block count can be set one time.
-
FSL_USDHC_ENABLE_SCATTER_GATHER_TRANSFER
USDHC scatter gather feature control macro.
-
USDHC_ADMA1_ADDRESS_ALIGN
The alignment size for ADDRESS filed in ADMA1’s descriptor.
-
USDHC_ADMA1_LENGTH_ALIGN
The alignment size for LENGTH field in ADMA1’s descriptor.
-
USDHC_ADMA2_ADDRESS_ALIGN
The alignment size for ADDRESS field in ADMA2’s descriptor.
-
USDHC_ADMA2_LENGTH_ALIGN
The alignment size for LENGTH filed in ADMA2’s descriptor.
-
USDHC_ADMA1_DESCRIPTOR_ADDRESS_SHIFT
The bit shift for ADDRESS filed in ADMA1’s descriptor.
Address/page field
Reserved
Attribute
31 12
11 6
05
04
03
02
01
00
address or data length
000000
Act2
Act1
0
Int
End
Valid
Act2
Act1
Comment
31-28
27-12
0
0
No op
Don’t care
0
1
Set data length
0000
Data Length
1
0
Transfer data
Data address
1
1
Link descriptor
Descriptor address
-
USDHC_ADMA1_DESCRIPTOR_ADDRESS_MASK
The bit mask for ADDRESS field in ADMA1’s descriptor.
-
USDHC_ADMA1_DESCRIPTOR_LENGTH_SHIFT
The bit shift for LENGTH filed in ADMA1’s descriptor.
-
USDHC_ADMA1_DESCRIPTOR_LENGTH_MASK
The mask for LENGTH field in ADMA1’s descriptor.
-
USDHC_ADMA1_DESCRIPTOR_MAX_LENGTH_PER_ENTRY
The maximum value of LENGTH filed in ADMA1’s descriptor. Since the max transfer size ADMA1 support is 65535 which is indivisible by 4096, so to make sure a large data load transfer (>64KB) continuously (require the data address be always align with 4096), software will set the maximum data length for ADMA1 to (64 - 4)KB.
-
USDHC_ADMA2_DESCRIPTOR_LENGTH_SHIFT
The bit shift for LENGTH field in ADMA2’s descriptor.
Address field
Length
Reserved
Attribute
63 32
31 16
15 06
05
04
03
02
01
00
32-bit address
16-bit length
0000000000
Act2
Act1
0
Int
End
Valid
Act2
Act1
Comment
Operation
0
0
No op
Don’t care
0
1
Reserved
Read this line and go to next one
1
0
Transfer data
Transfer data with address and length set in this descriptor line
1
1
Link descriptor
Link to another descriptor
-
USDHC_ADMA2_DESCRIPTOR_LENGTH_MASK
The bit mask for LENGTH field in ADMA2’s descriptor.
-
USDHC_ADMA2_DESCRIPTOR_MAX_LENGTH_PER_ENTRY
The maximum value of LENGTH field in ADMA2’s descriptor.
-
struct _usdhc_adma2_descriptor
- #include <fsl_usdhc.h>
Defines the ADMA2 descriptor structure.
Public Members
-
uint32_t attribute
The control and status field.
-
const uint32_t *address
The address field.
-
uint32_t attribute
-
struct _usdhc_capability
- #include <fsl_usdhc.h>
USDHC capability information.
Defines a structure to save the capability information of USDHC.
Public Members
-
uint32_t sdVersion
Support SD card/sdio version.
-
uint32_t mmcVersion
Support EMMC card version.
-
uint32_t maxBlockLength
Maximum block length united as byte.
-
uint32_t maxBlockCount
Maximum block count can be set one time.
-
uint32_t flags
Capability flags to indicate the support information(_usdhc_capability_flag).
-
uint32_t sdVersion
-
struct _usdhc_boot_config
- #include <fsl_usdhc.h>
Data structure to configure the MMC boot feature.
Public Members
-
uint32_t ackTimeoutCount
Timeout value for the boot ACK. The available range is 0 ~ 15.
-
usdhc_boot_mode_t bootMode
Boot mode selection.
-
uint32_t blockCount
Stop at block gap value of automatic mode. Available range is 0 ~ 65535.
-
size_t blockSize
Block size.
-
bool enableBootAck
Enable or disable boot ACK.
-
bool enableAutoStopAtBlockGap
Enable or disable auto stop at block gap function in boot period.
-
uint32_t ackTimeoutCount
-
struct _usdhc_config
- #include <fsl_usdhc.h>
Data structure to initialize the USDHC.
Public Members
-
uint32_t dataTimeout
Data timeout value.
-
usdhc_endian_mode_t endianMode
Endian mode.
-
uint8_t readWatermarkLevel
Watermark level for DMA read operation. Available range is 1 ~ 128.
-
uint8_t writeWatermarkLevel
Watermark level for DMA write operation. Available range is 1 ~ 128.
-
uint32_t dataTimeout
-
struct _usdhc_command
- #include <fsl_usdhc.h>
Card command descriptor.
Defines card command-related attribute.
Public Members
-
uint32_t index
Command index.
-
uint32_t argument
Command argument.
-
usdhc_card_command_type_t type
Command type.
-
usdhc_card_response_type_t responseType
Command response type.
-
uint32_t response[4U]
Response for this command.
-
uint32_t responseErrorFlags
Response error flag, which need to check the command reponse.
-
uint32_t flags
Cmd flags.
-
uint32_t index
-
struct _usdhc_adma_config
- #include <fsl_usdhc.h>
ADMA configuration.
Public Members
-
usdhc_dma_mode_t dmaMode
DMA mode.
-
uint32_t *admaTable
ADMA table address, can’t be null if transfer way is ADMA1/ADMA2.
-
uint32_t admaTableWords
ADMA table length united as words, can’t be 0 if transfer way is ADMA1/ADMA2.
-
usdhc_dma_mode_t dmaMode
-
struct _usdhc_scatter_gather_data_list
- #include <fsl_usdhc.h>
Card scatter gather data list.
Allow application register uncontinuous data buffer for data transfer.
-
struct _usdhc_scatter_gather_data
- #include <fsl_usdhc.h>
Card scatter gather data descriptor.
Defines a structure to contain data-related attribute. The ‘enableIgnoreError’ is used when upper card driver wants to ignore the error event to read/write all the data and not to stop read/write immediately when an error event happens. For example, bus testing procedure for MMC card.
Public Members
-
bool enableAutoCommand12
Enable auto CMD12.
-
bool enableAutoCommand23
Enable auto CMD23.
-
bool enableIgnoreError
Enable to ignore error event to read/write all the data.
-
usdhc_transfer_direction_t dataDirection
data direction
-
uint8_t dataType
this is used to distinguish the normal/tuning/boot data.
-
size_t blockSize
Block size.
-
usdhc_scatter_gather_data_list_t sgData
scatter gather data
-
bool enableAutoCommand12
-
struct _usdhc_scatter_gather_transfer
- #include <fsl_usdhc.h>
usdhc scatter gather transfer.
Public Members
-
usdhc_scatter_gather_data_t *data
Data to transfer.
-
usdhc_command_t *command
Command to send.
-
usdhc_scatter_gather_data_t *data
-
struct _usdhc_data
- #include <fsl_usdhc.h>
Card data descriptor.
Defines a structure to contain data-related attribute. The ‘enableIgnoreError’ is used when upper card driver wants to ignore the error event to read/write all the data and not to stop read/write immediately when an error event happens. For example, bus testing procedure for MMC card.
Public Members
-
bool enableAutoCommand12
Enable auto CMD12.
-
bool enableAutoCommand23
Enable auto CMD23.
-
bool enableIgnoreError
Enable to ignore error event to read/write all the data.
-
uint8_t dataType
this is used to distinguish the normal/tuning/boot data.
-
size_t blockSize
Block size.
-
uint32_t blockCount
Block count.
-
uint32_t *rxData
Buffer to save data read.
-
const uint32_t *txData
Data buffer to write.
-
bool enableAutoCommand12
-
struct _usdhc_transfer
- #include <fsl_usdhc.h>
Transfer state.
-
struct _usdhc_transfer_callback
- #include <fsl_usdhc.h>
USDHC callback functions.
Public Members
-
void (*CardInserted)(USDHC_Type *base, void *userData)
Card inserted occurs when DAT3/CD pin is for card detect
-
void (*CardRemoved)(USDHC_Type *base, void *userData)
Card removed occurs
-
void (*SdioInterrupt)(USDHC_Type *base, void *userData)
SDIO card interrupt occurs
-
void (*BlockGap)(USDHC_Type *base, void *userData)
stopped at block gap event
-
void (*TransferComplete)(USDHC_Type *base, usdhc_handle_t *handle, status_t status, void *userData)
Transfer complete callback.
-
void (*ReTuning)(USDHC_Type *base, void *userData)
Handle the re-tuning.
-
void (*CardInserted)(USDHC_Type *base, void *userData)
-
struct _usdhc_handle
- #include <fsl_usdhc.h>
USDHC handle.
Defines the structure to save the USDHC state information and callback function.
Note
All the fields except interruptFlags and transferredWords must be allocated by the user.
Public Members
-
usdhc_data_t *volatile data
Transfer parameter. Data to transfer.
-
usdhc_command_t *volatile command
Transfer parameter. Command to send.
-
volatile uint32_t transferredWords
Transfer status. Words transferred by DATAPORT way.
-
usdhc_transfer_callback_t callback
Callback function.
-
void *userData
Parameter for transfer complete callback.
-
usdhc_data_t *volatile data
-
struct _usdhc_host
- #include <fsl_usdhc.h>
USDHC host descriptor.
Public Members
-
USDHC_Type *base
USDHC peripheral base address.
-
uint32_t sourceClock_Hz
USDHC source clock frequency united in Hz.
-
usdhc_config_t config
USDHC configuration.
-
usdhc_capability_t capability
USDHC capability information.
-
usdhc_transfer_function_t transfer
USDHC transfer function.
-
USDHC_Type *base
WDOG: Watchdog Timer Driver
-
void WDOG_GetDefaultConfig(wdog_config_t *config)
Initializes the WDOG configuration structure.
This function initializes the WDOG configuration structure to default values. The default values are as follows.
wdogConfig->enableWdog = true; wdogConfig->workMode.enableWait = true; wdogConfig->workMode.enableStop = true; wdogConfig->workMode.enableDebug = true; wdogConfig->enableInterrupt = false; wdogConfig->enablePowerdown = false; wdogConfig->resetExtension = flase; wdogConfig->timeoutValue = 0xFFU; wdogConfig->interruptTimeValue = 0x04u;
See also
wdog_config_t
- Parameters:
config – Pointer to the WDOG configuration structure.
-
void WDOG_Init(WDOG_Type *base, const wdog_config_t *config)
Initializes the WDOG.
This function initializes the WDOG. When called, the WDOG runs according to the configuration.
This is an example.
wdog_config_t config; WDOG_GetDefaultConfig(&config); config.timeoutValue = 0xffU; config->interruptTimeValue = 0x04u; WDOG_Init(wdog_base,&config);
- Parameters:
base – WDOG peripheral base address
config – The configuration of WDOG
-
void WDOG_Deinit(WDOG_Type *base)
Shuts down the WDOG.
This function shuts down the WDOG. Watchdog Enable bit is a write one once only bit. It is not possible to clear this bit by a software write, once the bit is set. This bit(WDE) can be set/reset only in debug mode(exception).
-
static inline void WDOG_Enable(WDOG_Type *base)
Enables the WDOG module.
This function writes a value into the WDOG_WCR register to enable the WDOG. This is a write one once only bit. It is not possible to clear this bit by a software write, once the bit is set. only debug mode exception.
- Parameters:
base – WDOG peripheral base address
-
static inline void WDOG_Disable(WDOG_Type *base)
Disables the WDOG module.
This function writes a value into the WDOG_WCR register to disable the WDOG. This is a write one once only bit. It is not possible to clear this bit by a software write,once the bit is set. only debug mode exception
- Parameters:
base – WDOG peripheral base address
-
static inline void WDOG_TriggerSystemSoftwareReset(WDOG_Type *base)
Trigger the system software reset.
This function will write to the WCR[SRS] bit to trigger a software system reset. This bit will automatically resets to “1” after it has been asserted to “0”. Note: Calling this API will reset the system right now, please using it with more attention.
- Parameters:
base – WDOG peripheral base address
-
static inline void WDOG_TriggerSoftwareSignal(WDOG_Type *base)
Trigger an output assertion.
This function will write to the WCR[WDA] bit to trigger WDOG_B signal assertion. The WDOG_B signal can be routed to external pin of the chip, the output pin will turn to assertion along with WDOG_B signal. Note: The WDOG_B signal will remain assert until a power on reset occurred, so, please take more attention while calling it.
- Parameters:
base – WDOG peripheral base address
-
static inline void WDOG_EnableInterrupts(WDOG_Type *base, uint16_t mask)
Enables the WDOG interrupt.
This bit is a write once only bit. Once the software does a write access to this bit, it will get locked and cannot be reprogrammed until the next system reset assertion
- Parameters:
base – WDOG peripheral base address
mask – The interrupts to enable The parameter can be combination of the following source if defined.
kWDOG_InterruptEnable
-
uint16_t WDOG_GetStatusFlags(WDOG_Type *base)
Gets the WDOG all reset status flags.
This function gets all reset status flags.
uint16_t status; status = WDOG_GetStatusFlags (wdog_base);
See also
_wdog_status_flags
true: a related status flag has been set.
false: a related status flag is not set.
- Parameters:
base – WDOG peripheral base address
- Returns:
State of the status flag: asserted (true) or not-asserted (false).
-
void WDOG_ClearInterruptStatus(WDOG_Type *base, uint16_t mask)
Clears the WDOG flag.
This function clears the WDOG status flag.
This is an example for clearing the interrupt flag.
WDOG_ClearStatusFlags(wdog_base,KWDOG_InterruptFlag);
- Parameters:
base – WDOG peripheral base address
mask – The status flags to clear. The parameter could be any combination of the following values. kWDOG_TimeoutFlag
-
static inline void WDOG_SetTimeoutValue(WDOG_Type *base, uint16_t timeoutCount)
Sets the WDOG timeout value.
This function sets the timeout value. This function writes a value into WCR registers. The time-out value can be written at any point of time but it is loaded to the counter at the time when WDOG is enabled or after the service routine has been performed.
- Parameters:
base – WDOG peripheral base address
timeoutCount – WDOG timeout value; count of WDOG clock tick.
-
static inline void WDOG_SetInterrputTimeoutValue(WDOG_Type *base, uint16_t timeoutCount)
Sets the WDOG interrupt count timeout value.
This function sets the interrupt count timeout value. This function writes a value into WIC registers which are wirte-once. This field is write once only. Once the software does a write access to this field, it will get locked and cannot be reprogrammed until the next system reset assertion.
- Parameters:
base – WDOG peripheral base address
timeoutCount – WDOG timeout value; count of WDOG clock tick.
-
static inline void WDOG_DisablePowerDownEnable(WDOG_Type *base)
Disable the WDOG power down enable bit.
This function disable the WDOG power down enable(PDE). This function writes a value into WMCR registers which are wirte-once. This field is write once only. Once software sets this bit it cannot be reset until the next system reset.
- Parameters:
base – WDOG peripheral base address
-
void WDOG_Refresh(WDOG_Type *base)
Refreshes the WDOG timer.
This function feeds the WDOG. This function should be called before the WDOG timer is in timeout. Otherwise, a reset is asserted.
- Parameters:
base – WDOG peripheral base address
-
FSL_WDOG_DRIVER_VERSION
Defines WDOG driver version.
-
WDOG_REFRESH_KEY
-
enum _wdog_interrupt_enable
WDOG interrupt configuration structure, default settings all disabled.
This structure contains the settings for all of the WDOG interrupt configurations.
Values:
-
enumerator kWDOG_InterruptEnable
WDOG timeout generates an interrupt before reset
-
enumerator kWDOG_InterruptEnable
-
enum _wdog_status_flags
WDOG status flags.
This structure contains the WDOG status flags for use in the WDOG functions.
Values:
-
enumerator kWDOG_RunningFlag
Running flag, set when WDOG is enabled
-
enumerator kWDOG_PowerOnResetFlag
Power On flag, set when reset is the result of a powerOnReset
-
enumerator kWDOG_TimeoutResetFlag
Timeout flag, set when reset is the result of a timeout
-
enumerator kWDOG_SoftwareResetFlag
Software flag, set when reset is the result of a software
-
enumerator kWDOG_InterruptFlag
interrupt flag,whether interrupt has occurred or not
-
enumerator kWDOG_RunningFlag
-
typedef struct _wdog_work_mode wdog_work_mode_t
Defines WDOG work mode.
-
typedef struct _wdog_config wdog_config_t
Describes WDOG configuration structure.
-
struct _wdog_work_mode
- #include <fsl_wdog.h>
Defines WDOG work mode.
Public Members
-
bool enableWait
If set to true, WDOG continues in wait mode
-
bool enableStop
If set to true, WDOG continues in stop mode
-
bool enableDebug
If set to true, WDOG continues in debug mode
-
bool enableWait
-
struct _wdog_config
- #include <fsl_wdog.h>
Describes WDOG configuration structure.
Public Members
-
bool enableWdog
Enables or disables WDOG
-
wdog_work_mode_t workMode
Configures WDOG work mode in debug stop and wait mode
-
bool enableInterrupt
Enables or disables WDOG interrupt
-
uint16_t timeoutValue
Timeout value
-
uint16_t interruptTimeValue
Interrupt count timeout value
-
bool softwareResetExtension
software reset extension
-
bool enablePowerDown
power down enable bit
-
bool enableTimeOutAssert
Enable WDOG_B timeout assertion.
-
bool enableWdog
XBARA: Inter-Peripheral Crossbar Switch
-
void XBARA_Init(XBARA_Type *base)
Initializes the XBARA module.
This function un-gates the XBARA clock.
- Parameters:
base – XBARA peripheral address.
-
void XBARA_Deinit(XBARA_Type *base)
Shuts down the XBARA module.
This function disables XBARA clock.
- Parameters:
base – XBARA peripheral address.
-
void XBARA_SetSignalsConnection(XBARA_Type *base, xbar_input_signal_t input, xbar_output_signal_t output)
Sets a connection between the selected XBARA_IN[*] input and the XBARA_OUT[*] output signal.
This function connects the XBARA input to the selected XBARA output. If more than one XBARA module is available, only the inputs and outputs from the same module can be connected.
Example:
XBARA_SetSignalsConnection(XBARA, kXBARA_InputPIT_TRG0, kXBARA_OutputDMAMUX18);
- Parameters:
base – XBARA peripheral address.
input – XBARA input signal.
output – XBARA output signal.
-
uint32_t XBARA_GetStatusFlags(XBARA_Type *base)
Gets the active edge detection status.
This function gets the active edge detect status of all XBARA_OUTs. If the active edge occurs, the return value is asserted. When the interrupt or the DMA functionality is enabled for the XBARA_OUTx, this field is 1 when the interrupt or DMA request is asserted and 0 when the interrupt or DMA request has been cleared.
- Parameters:
base – XBARA peripheral address.
- Returns:
the mask of these status flag bits.
-
void XBARA_ClearStatusFlags(XBARA_Type *base, uint32_t mask)
Clears the edge detection status flags of relative mask.
- Parameters:
base – XBARA peripheral address.
mask – the status flags to clear.
-
void XBARA_SetOutputSignalConfig(XBARA_Type *base, xbar_output_signal_t output, const xbara_control_config_t *controlConfig)
Configures the XBARA control register.
This function configures an XBARA control register. The active edge detection and the DMA/IRQ function on the corresponding XBARA output can be set.
Example:
xbara_control_config_t userConfig; userConfig.activeEdge = kXBARA_EdgeRising; userConfig.requestType = kXBARA_RequestInterruptEnalbe; XBARA_SetOutputSignalConfig(XBARA, kXBARA_OutputDMAMUX18, &userConfig);
- Parameters:
base – XBARA peripheral address.
output – XBARA output number.
controlConfig – Pointer to structure that keeps configuration of control register.
-
enum _xbara_active_edge
XBARA active edge for detection.
Values:
-
enumerator kXBARA_EdgeNone
Edge detection status bit never asserts.
-
enumerator kXBARA_EdgeRising
Edge detection status bit asserts on rising edges.
-
enumerator kXBARA_EdgeFalling
Edge detection status bit asserts on falling edges.
-
enumerator kXBARA_EdgeRisingAndFalling
Edge detection status bit asserts on rising and falling edges.
-
enumerator kXBARA_EdgeNone
-
enum _xbar_request
Defines the XBARA DMA and interrupt configurations.
Values:
-
enumerator kXBARA_RequestDisable
Interrupt and DMA are disabled.
-
enumerator kXBARA_RequestDMAEnable
DMA enabled, interrupt disabled.
-
enumerator kXBARA_RequestInterruptEnable
Interrupt enabled, DMA disabled.
-
enumerator kXBARA_RequestDisable
-
enum _xbara_status_flag_t
XBARA status flags.
This provides constants for the XBARA status flags for use in the XBARA functions.
Values:
-
enumerator kXBARA_EdgeDetectionOut0
XBAR_OUT0 active edge interrupt flag, sets when active edge detected.
-
enumerator kXBARA_EdgeDetectionOut1
XBAR_OUT1 active edge interrupt flag, sets when active edge detected.
-
enumerator kXBARA_EdgeDetectionOut2
XBAR_OUT2 active edge interrupt flag, sets when active edge detected.
-
enumerator kXBARA_EdgeDetectionOut3
XBAR_OUT3 active edge interrupt flag, sets when active edge detected.
-
enumerator kXBARA_EdgeDetectionOut0
-
typedef enum _xbara_active_edge xbara_active_edge_t
XBARA active edge for detection.
-
typedef enum _xbar_request xbara_request_t
Defines the XBARA DMA and interrupt configurations.
-
typedef enum _xbara_status_flag_t xbara_status_flag_t
XBARA status flags.
This provides constants for the XBARA status flags for use in the XBARA functions.
-
typedef struct XBARAControlConfig xbara_control_config_t
Defines the configuration structure of the XBARA control register.
This structure keeps the configuration of XBARA control register for one output. Control registers are available only for a few outputs. Not every XBARA module has control registers.
-
FSL_XBARA_DRIVER_VERSION
-
XBARA_SELx(base, output)
-
XBARA_WR_SELx_SELx(base, input, output)
-
kXBARA_RequestInterruptEnalbe
-
struct XBARAControlConfig
- #include <fsl_xbara.h>
Defines the configuration structure of the XBARA control register.
This structure keeps the configuration of XBARA control register for one output. Control registers are available only for a few outputs. Not every XBARA module has control registers.
Public Members
-
xbara_active_edge_t activeEdge
Active edge to be detected.
-
xbara_request_t requestType
Selects DMA/Interrupt request.
-
xbara_active_edge_t activeEdge
XBARB: Inter-Peripheral Crossbar Switch
-
void XBARB_Init(XBARB_Type *base)
Initializes the XBARB module.
This function un-gates the XBARB clock.
- Parameters:
base – XBARB peripheral address.
-
void XBARB_Deinit(XBARB_Type *base)
Shuts down the XBARB module.
This function disables XBARB clock.
- Parameters:
base – XBARB peripheral address.
-
void XBARB_SetSignalsConnection(XBARB_Type *base, xbar_input_signal_t input, xbar_output_signal_t output)
Configures a connection between the selected XBARB_IN[*] input and the XBARB_OUT[*] output signal.
This function configures which XBARB input is connected to the selected XBARB output. If more than one XBARB module is available, only the inputs and outputs from the same module can be connected.
- Parameters:
base – XBARB peripheral address.
input – XBARB input signal.
output – XBARB output signal.
-
FSL_XBARB_DRIVER_VERSION
-
XBARB_SELx(base, output)
-
XBARB_WR_SELx_SELx(base, input, output)